diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/msm-hsusb.txt')
-rw-r--r-- | Documentation/devicetree/bindings/usb/msm-hsusb.txt | 67 |
1 files changed, 67 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index 5ea26c6..ee4123d 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -15,3 +15,70 @@ Example EHCI controller device node: usb-phy = <&usb_otg>; }; +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + }; |