diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
4 files changed, 27 insertions, 16 deletions
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt index b82a268..bee6ff2 100644 --- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt @@ -23,6 +23,12 @@ Optional properties: - spi-max-frequency: Specifies maximum SPI clock frequency, Units - Hz. Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +- num-cs: total number of chipselects +- cs-gpios: should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child + nodes. If unspecified, a single SPI device without a chip + select can be used. + SPI slave nodes must be children of the SPI master node and can contain properties described in Documentation/devicetree/bindings/spi/spi-bus.txt diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 22d5740..bbaa857 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -63,7 +63,7 @@ contain the following properties. used for MISO. Defaults to 1 if not present. Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD). +It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is only 1(SINGLE), 2(DUAL) and 4(QUAD). Dual/Quad mode is not allowed when 3-wire mode is used. diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index 6d0ac8d..f80887b 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -8,7 +8,8 @@ Required properties: - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family - reg: Offset and length of SPI controller register space -- num-cs: Number of chip selects +- num-cs: Number of chip selects. This includes internal as well as + GPIO chip selects. - ti,davinci-spi-intr-line: interrupt line used to connect the SPI IP to the interrupt controller within the SoC. Possible values are 0 and 1. Manual says one of the two possible interrupt @@ -17,6 +18,12 @@ Required properties: - interrupts: interrupt number mapped to CPU. - clocks: spi clk phandle +Optional: +- cs-gpios: gpio chip selects + For example to have 3 internal CS and 2 GPIO CS, user could define + cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>; + where first three are internal CS and last two are GPIO CS. + Example of a NOR flash slave device (n25q032) connected to DaVinci SPI controller device over the SPI bus. diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index 86aa061..792efba 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -18,14 +18,11 @@ Required SoC Specific Properties: - interrupts: The interrupt number to the cpu. The interrupt specifier format depends on the interrupt controller. -[PRELIMINARY: the dma channel allocation will change once there are -official DMA bindings] +- dmas : Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt -- tx-dma-channel: The dma channel specifier for tx operations. The format of - the dma specifier depends on the dma controller. - -- rx-dma-channel: The dma channel specifier for rx operations. The format of - the dma specifier depends on the dma controller. +- dma-names: Names for the dma channels. There must be at least one channel + named "tx" for transmit and named "rx" for receive. Required Board Specific Properties: @@ -42,15 +39,13 @@ Optional Board Specific Properties: - num-cs: Specifies the number of chip select lines supported. If not specified, the default number of chip select lines is set to 1. +- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt) + SPI Controller specific data in SPI slave nodes: - The spi slave nodes should provide the following information which is required by the spi controller. - - cs-gpio: A gpio specifier that specifies the gpio line used as - the slave select line by the spi controller. The format of the gpio - specifier depends on the gpio controller. - - samsung,spi-feedback-delay: The sampling phase shift to be applied on the miso line (to account for any lag in the miso line). The following are the valid values. @@ -74,8 +69,11 @@ Example: compatible = "samsung,exynos4210-spi"; reg = <0x12d20000 0x100>; interrupts = <0 66 0>; - tx-dma-channel = <&pdma0 5>; - rx-dma-channel = <&pdma0 4>; + dmas = <&pdma0 5 + &pdma0 4>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; }; - Board Specific Portion: @@ -85,6 +83,7 @@ Example: #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&spi0_bus>; + cs-gpios = <&gpa2 5 0>; w25q80bw@0 { #address-cells = <1>; @@ -94,7 +93,6 @@ Example: spi-max-frequency = <10000>; controller-data { - cs-gpio = <&gpa2 5 1 0 3>; samsung,spi-feedback-delay = <0>; }; |
