diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
4 files changed, 76 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index e865855..bdd8395 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -1,7 +1,9 @@ Renesas MSIOF spi controller Required properties: -- compatible : "renesas,msiof-r8a7790" (R-Car H2) +- compatible : "renesas,msiof-r8a7743" (RZ/G1M) + "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) @@ -10,7 +12,7 @@ Required properties: "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-sh73a0" (SH-Mobile AG5) "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) - "renesas,rcar-gen2-msiof" (generic R-Car Gen2 compatible device) + "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device) "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) "renesas,sh-msiof" (deprecated) diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index f5916c9..1925277 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -24,6 +24,16 @@ Required properties: based on a specific SoC configuration. - interrupts: interrupt number mapped to CPU. - clocks: spi clk phandle + For 66AK2G this property should be set per binding, + Documentation/devicetree/bindings/clock/ti,sci-clk.txt + +SoC-specific Required Properties: + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: + +- power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the SPI device id + value. This property is as per the binding, Optional: - cs-gpios: gpio chip selects diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt index 8f4169f..3b02b3a 100644 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -5,11 +5,14 @@ Required properties: "renesas,rspi-<soctype>", "renesas,rspi" as fallback. For Renesas Serial Peripheral Interface on RZ/A1H: "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. - For Quad Serial Peripheral Interface on R-Car Gen2: + For Quad Serial Peripheral Interface on R-Car Gen2 and + RZ/G1 devices: "renesas,qspi-<soctype>", "renesas,qspi" as fallback. Examples with soctypes are: - "renesas,rspi-sh7757" (SH) - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,qspi-r8a7743" (RZ/G1M) + - "renesas,qspi-r8a7745" (RZ/G1E) - "renesas,qspi-r8a7790" (R-Car H2) - "renesas,qspi-r8a7791" (R-Car M2-W) - "renesas,qspi-r8a7792" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt b/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt new file mode 100644 index 0000000..8de589b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sprd-adi.txt @@ -0,0 +1,58 @@ +Spreadtrum ADI controller + +ADI is the abbreviation of Anolog-Digital interface, which is used to access +analog chip (such as PMIC) from digital chip. ADI controller follows the SPI +framework for its hardware implementation is alike to SPI bus and its timing +is compatile to SPI timing. + +ADI controller has 50 channels including 2 software read/write channels and +48 hardware channels to access analog chip. For 2 software read/write channels, +users should set ADI registers to access analog chip. For hardware channels, +we can configure them to allow other hardware components to use it independently, +which means we can just link one analog chip address to one hardware channel, +then users can access the mapped analog chip address by this hardware channel +triggered by hardware components instead of ADI software channels. + +Thus we introduce one property named "sprd,hw-channels" to configure hardware +channels, the first value specifies the hardware channel id which is used to +transfer data triggered by hardware automatically, and the second value specifies +the analog chip address where user want to access by hardware components. + +Since we have multi-subsystems will use unique ADI to access analog chip, when +one system is reading/writing data by ADI software channels, that should be under +one hardware spinlock protection to prevent other systems from reading/writing +data by ADI software channels at the same time, or two parallel routine of setting +ADI registers will make ADI controller registers chaos to lead incorrect results. +Then we need one hardware spinlock to synchronize between the multiple subsystems. + +Required properties: +- compatible: Should be "sprd,sc9860-adi". +- reg: Offset and length of ADI-SPI controller register space. +- hwlocks: Reference to a phandle of a hwlock provider node. +- hwlock-names: Reference to hwlock name strings defined in the same order + as the hwlocks, should be "adi". +- #address-cells: Number of cells required to define a chip select address + on the ADI-SPI bus. Should be set to 1. +- #size-cells: Size of cells required to define a chip select address size + on the ADI-SPI bus. Should be set to 0. + +Optional properties: +- sprd,hw-channels: This is an array of channel values up to 49 channels. + The first value specifies the hardware channel id which is used to + transfer data triggered by hardware automatically, and the second + value specifies the analog chip address where user want to access + by hardware components. + +SPI slave nodes must be children of the SPI controller node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + adi_bus: spi@40030000 { + compatible = "sprd,sc9860-adi"; + reg = <0 0x40030000 0 0x10000>; + hwlocks = <&hwlock1 0>; + hwlock-names = "adi"; + #address-cells = <1>; + #size-cells = <0>; + sprd,hw-channels = <30 0x8c20>; + }; |