diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
3 files changed, 76 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/regulator/pv88080.txt b/Documentation/devicetree/bindings/regulator/pv88080.txt new file mode 100644 index 0000000..38a6142 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pv88080.txt @@ -0,0 +1,49 @@ +* Powerventure Semiconductor PV88080 Voltage Regulator + +Required properties: +- compatible: "pvs,pv88080". +- reg: I2C slave address, usually 0x49. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCK1, BUCK2, and BUCK3. + +Optional properties: +- Any optional property defined in regulator.txt + +Example + + pmic: pv88080@49 { + compatible = "pvs,pv88080"; + reg = <0x49>; + interrupt-parent = <&gpio>; + interrupts = <24 24>; + + regulators { + BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = < 220000>; + regulator-max-microamp = <7040000>; + }; + + BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + }; + + BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <2193750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt index b3c8ca6..1c4bfe7 100644 --- a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt +++ b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt @@ -94,6 +94,28 @@ Following are additional properties: This is applicable if suspend state FPS source is selected as FPS0, FPS1 or FPS2. +- maxim,ramp-rate-setting: integer, ramp rate(uV/us) setting to be + configured to the device. + The platform may have different ramp + rate than advertised ramp rate if it has + design variation from Maxim's + recommended. On this case, platform + specific ramp rate is used for ramp time + calculation and this property is used + for device register configurations. + The measured ramp rate of platform is + provided by the regulator-ramp-delay + as described in <devicetree/bindings/ + regulator/regulator.txt>. + Maxim Max77620 supports following ramp + delay: + SD: 13.75mV/us, 27.5mV/us, 55mV/us + LDOs: 5mV/us, 100mV/us + +Note: If the measured ramp delay is same as advertised ramp delay then it is not +required to provide the ramp delay with property "maxim,ramp-rate-setting". The +ramp rate can be provided by the regulator-ramp-delay which will be used for +ramp time calculation for voltage change as well as for device configuration. Example: -------- diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt index c58db75..c3f6546 100644 --- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -14,8 +14,8 @@ Required Properties: - "setup-address" - contains setup register address of ABB module (ti,abb-v3) - "int-address" - contains address of interrupt register for ABB module (also see Optional properties) -- #address-cell: should be 0 -- #size-cell: should be 0 +- #address-cells: should be 0 +- #size-cells: should be 0 - clocks: should point to the clock node used by ABB module - ti,settling-time: Settling time in uSecs from SoC documentation for ABB module to settle down(target time for SR2_WTCNT_VALUE). @@ -69,7 +69,7 @@ Example #1: Simplest configuration (no efuse data, hard coded ABB table): abb_x: regulator-abb-x { compatible = "ti,abb-v1"; regulator-name = "abb_x"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x483072f0 0x8>, <0x48306818 0x4>; reg-names = "base-address", "int-address"; @@ -89,7 +89,7 @@ Example #2: Efuse bits contain ABB mode setting (no LDO override capability) abb_y: regulator-abb-y { compatible = "ti,abb-v2"; regulator-name = "abb_y"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; reg-names = "base-address", "int-address", "efuse-address"; @@ -110,7 +110,7 @@ Example #3: Efuse bits contain ABB mode setting and LDO override capability abb_z: regulator-abb-z { compatible = "ti,abb-v2"; regulator-name = "abb_z"; - #address-cell = <0>; + #address-cells = <0>; #size-cells = <0>; reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, <0x4a002194 0x8>, <0x4ae0C314 0x4>; |
