diff options
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
5 files changed, 207 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index c6dd3f5..f0ada3b 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -21,7 +21,7 @@ Each regulator is defined using the standard binding for regulators. Example 1: PFUZE100 - pmic: pfuze100@8 { + pfuze100: pmic@8 { compatible = "fsl,pfuze100"; reg = <0x08>; @@ -122,7 +122,7 @@ Example 1: PFUZE100 Example 2: PFUZE200 - pmic: pfuze200@8 { + pfuze200: pmic@8 { compatible = "fsl,pfuze200"; reg = <0x08>; @@ -216,7 +216,7 @@ Example 2: PFUZE200 Example 3: PFUZE3000 - pmic: pfuze3000@8 { + pfuze3000: pmic@8 { compatible = "fsl,pfuze3000"; reg = <0x08>; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 57d2c658..406f2e5 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -110,6 +110,11 @@ Qualcomm SPMI Regulators Definition: Reference to regulator supplying the input pin, as described in the data sheet. +- qcom,saw-reg: + Usage: optional + Value type: <phandle> + Description: Reference to syscon node defining the SAW registers. + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each @@ -201,6 +206,17 @@ see regulator.txt - with additional custom properties described below: 2 = 0.55 uA 3 = 0.75 uA +- qcom,saw-slave: + Usage: optional + Value type: <boo> + Description: SAW controlled gang slave. Will not be configured. + +- qcom,saw-leader: + Usage: optional + Value type: <boo> + Description: SAW controlled gang leader. Will be configured as + SAW regulator. + Example: regulators { @@ -221,3 +237,32 @@ Example: .... }; + +Example 2: + + saw3: syscon@9A10000 { + compatible = "syscon"; + reg = <0x9A10000 0x1000>; + }; + + ... + + spm-regulators { + compatible = "qcom,pm8994-regulators"; + qcom,saw-reg = <&saw3>; + s8 { + qcom,saw-slave; + }; + s9 { + qcom,saw-slave; + }; + s10 { + qcom,saw-slave; + }; + pm8994_s11_saw: s11 { + qcom,saw-leader; + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1140000>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 2babe15b..a7cd368 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -59,6 +59,11 @@ Optional properties: - regulator-initial-mode: initial operating mode. The set of possible operating modes depends on the capabilities of every hardware so each device binding documentation explains which values the regulator supports. +- regulator-allowed-modes: list of operating modes that software is allowed to + configure for the regulator at run-time. Elements may be specified in any + order. The set of possible operating modes depends on the capabilities of + every hardware so each device binding document explains which values the + regulator supports. - regulator-system-load: Load in uA present on regulator that is not captured by any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. @@ -68,6 +73,11 @@ Optional properties: 0: Disable active discharge. 1: Enable active discharge. Absence of this property will leave configuration to default. +- regulator-coupled-with: Regulators with which the regulator + is coupled. The linkage is 2-way - all coupled regulators should be linked + with each other. A regulator should not be coupled with its supplier. +- regulator-coupled-max-spread: Max spread between voltages of coupled regulators + in microvolts. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt new file mode 100644 index 0000000..4edf313 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -0,0 +1,126 @@ +ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings + +BD71837MWV is a programmable Power Management +IC (PMIC) for powering single-core, dual-core, and +quad-core SoC’s such as NXP-i.MX 8M. It is optimized +for low BOM cost and compact solution footprint. It +integrates 8 Buck regulators and 7 LDO’s to provide all +the power rails required by the SoC and the commonly +used peripherals. + +Required properties: + - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" + +List of regulators provided by this controller. BD71837 regulators node +should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at +Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +Regulator nodes should be named to BUCK_<number> and LDO_<number>. The +definition for each of these nodes is defined using the standard +binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. +Note that if BD71837 starts at RUN state you probably want to use +regulator-boot-on at least for BUCK6 and BUCK7 so that those are not +disabled by driver at startup. LDO5 and LDO6 are supplied by those and +if they are disabled at startup the voltage monitoring for LDO5/LDO6 will +cause PMIC to reset. + +The valid names for regulator nodes are: +BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8 +LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: +regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-ramp-delay = <1250>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + }; + buck4: BUCK4 { + regulator-name = "buck4"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + }; + buck5: BUCK5 { + regulator-name = "buck5"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + }; + buck6: BUCK6 { + regulator-name = "buck6"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + buck7: BUCK7 { + regulator-name = "buck7"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + }; + buck8: BUCK8 { + regulator-name = "buck8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + }; + + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + }; + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + ldo4: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + }; + ldo5: LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + ldo6: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + }; + ldo7_reg: LDO7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; +}; + + diff --git a/Documentation/devicetree/bindings/regulator/sy8106a-regulator.txt b/Documentation/devicetree/bindings/regulator/sy8106a-regulator.txt new file mode 100644 index 0000000..39a8ca7 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/sy8106a-regulator.txt @@ -0,0 +1,23 @@ +SY8106A Voltage regulator + +Required properties: +- compatible: Must be "silergy,sy8106a" +- reg: I2C slave address - must be <0x65> +- silergy,fixed-microvolt - the voltage when I2C regulating is disabled (set + by external resistor like a fixed voltage) + +Any property defined as part of the core regulator binding, defined in +./regulator.txt, can also be used. + +Example: + + sy8106a { + compatible = "silergy,sy8106a"; + reg = <0x65>; + regulator-name = "sy8106a-vdd"; + silergy,fixed-microvolt = <1200000>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; |