diff options
Diffstat (limited to 'Documentation/devicetree/bindings/powerpc/fsl')
30 files changed, 1661 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt new file mode 100644 index 0000000..39e9415 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt @@ -0,0 +1,63 @@ +* Board Control and Status (BCSR) + +Required properties: + + - compatible : Should be "fsl,<board>-bcsr" + - reg : Offset and length of the register set for the device + +Example: + + bcsr@f8000000 { + compatible = "fsl,mpc8360mds-bcsr"; + reg = <f8000000 8000>; + }; + +* Freescale on board FPGA + +This is the memory-mapped registers for on board FPGA. + +Required properities: +- compatible : should be "fsl,fpga-pixis". +- reg : should contain the address and the length of the FPPGA register + set. +- interrupt-parent: should specify phandle for the interrupt controller. +- interrupts : should specify event (wakeup) IRQ. + +Example (MPC8610HPCD): + + board-control@e8000000 { + compatible = "fsl,fpga-pixis"; + reg = <0xe8000000 32>; + interrupt-parent = <&mpic>; + interrupts = <8 8>; + }; + +* Freescale BCSR GPIO banks + +Some BCSR registers act as simple GPIO controllers, each such +register can be represented by the gpio-controller node. + +Required properities: +- compatible : Should be "fsl,<board>-bcsr-gpio". +- reg : Should contain the address and the length of the GPIO bank + register. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example: + + bcsr@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8360mds-bcsr"; + reg = <1 0 0x8000>; + ranges = <0 1 0 0x8000>; + + bcsr13: gpio-controller@d { + #gpio-cells = <2>; + compatible = "fsl,mpc8360mds-bcsr-gpio"; + reg = <0xd 1>; + gpio-controller; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt new file mode 100644 index 0000000..160c752 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm.txt @@ -0,0 +1,67 @@ +* Freescale Communications Processor Module + +NOTE: This is an interim binding, and will likely change slightly, +as more devices are supported. The QE bindings especially are +incomplete. + +* Root CPM node + +Properties: +- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". +- reg : A 48-byte region beginning with CPCR. + +Example: + cpm@119c0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; + reg = <119c0 30>; + } + +* Properties common to multiple CPM/QE devices + +- fsl,cpm-command : This value is ORed with the opcode and command flag + to specify the device on which a CPM command operates. + +- fsl,cpm-brg : Indicates which baud rate generator the device + is associated with. If absent, an unused BRG + should be dynamically allocated. If zero, the + device uses an external clock rather than a BRG. + +- reg : Unless otherwise specified, the first resource represents the + scc/fcc/ucc registers, and the second represents the device's + parameter RAM region (if it has one). + +* Multi-User RAM (MURAM) + +The multi-user/dual-ported RAM is expressed as a bus under the CPM node. + +Ranges must be set up subject to the following restrictions: + +- Children's reg nodes must be offsets from the start of all muram, even + if the user-data area does not begin at zero. +- If multiple range entries are used, the difference between the parent + address and the child address must be the same in all, so that a single + mapping can cover them all while maintaining the ability to determine + CPM-side offsets with pointer subtraction. It is recommended that + multiple range entries not be used. +- A child address of zero must be translatable, even if no reg resources + contain it. + +A child "data" node must exist, compatible with "fsl,cpm-muram-data", to +indicate the portion of muram that is usable by the OS for arbitrary +purposes. The data node may have an arbitrary number of reg resources, +all of which contribute to the allocatable muram pool. + +Example, based on mpc8272: + muram@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 10000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0 2000 9800 800>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt new file mode 100644 index 0000000..4c7d45e --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/brg.txt @@ -0,0 +1,21 @@ +* Baud Rate Generators + +Currently defined compatibles: +fsl,cpm-brg +fsl,cpm1-brg +fsl,cpm2-brg + +Properties: +- reg : There may be an arbitrary number of reg resources; BRG + numbers are assigned to these in order. +- clock-frequency : Specifies the base frequency driving + the BRG. + +Example: + brg@119f0 { + compatible = "fsl,mpc8272-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <119f0 10 115f0 10>; + clock-frequency = <d#25000000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt new file mode 100644 index 0000000..87bc604 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/i2c.txt @@ -0,0 +1,41 @@ +* I2C + +The I2C controller is expressed as a bus under the CPM node. + +Properties: +- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" +- reg : On CPM2 devices, the second resource doesn't specify the I2C + Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM + (typically 0x8afc 0x2). +- #address-cells : Should be one. The cell is the i2c device address with + the r/w bit set to zero. +- #size-cells : Should be zero. +- clock-frequency : Can be used to set the i2c clock frequency. If + unspecified, a default frequency of 60kHz is being used. +The following two properties are deprecated. They are only used by legacy +i2c drivers to find the bus to probe: +- linux,i2c-index : Can be used to hard code an i2c bus number. By default, + the bus number is dynamically assigned by the i2c core. +- linux,i2c-class : Can be used to override the i2c class. The class is used + by legacy i2c device drivers to find a bus in a specific context like + system management, video or sound. By default, I2C_CLASS_HWMON (1) is + being used. The definition of the classes can be found in + include/i2c/i2c.h + +Example, based on mpc823: + + i2c@860 { + compatible = "fsl,mpc823-i2c", + "fsl,cpm1-i2c"; + reg = <0x860 0x20 0x3c80 0x30>; + interrupts = <16>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt new file mode 100644 index 0000000..8e3ee16 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/pic.txt @@ -0,0 +1,18 @@ +* Interrupt Controllers + +Currently defined compatibles: +- fsl,cpm1-pic + - only one interrupt cell +- fsl,pq1-pic +- fsl,cpm2-pic + - second interrupt cell is level/sense: + - 2 is falling edge + - 8 is active low + +Example: + interrupt-controller@10c00 { + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + compatible = "mpc8272-pic", "fsl,cpm2-pic"; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt new file mode 100644 index 0000000..74bfda4 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/cpm/usb.txt @@ -0,0 +1,15 @@ +* USB (Universal Serial Bus Controller) + +Properties: +- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" + +Example: + usb@11bc0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,cpm2-usb"; + reg = <11b60 18 8b00 100>; + interrupts = <b 8>; + interrupt-parent = <&PIC>; + fsl,cpm-command = <2e600000>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt new file mode 100644 index 0000000..349f79f --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/gpio.txt @@ -0,0 +1,38 @@ +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. + +On CPM1 devices, all ports are using slightly different register layouts. +Ports A, C and D are 16bit ports and Ports B and E are 32bit ports. + +On CPM2 devices, all ports are 32bit ports and use a common register layout. + +Required properties: +- compatible : "fsl,cpm1-pario-bank-a", "fsl,cpm1-pario-bank-b", + "fsl,cpm1-pario-bank-c", "fsl,cpm1-pario-bank-d", + "fsl,cpm1-pario-bank-e", "fsl,cpm2-pario-bank" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the port as GPIO controller. + +Example of three SOC GPIO banks defined as gpio-controller nodes: + + CPM1_PIO_A: gpio-controller@950 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-a"; + reg = <0x950 0x10>; + gpio-controller; + }; + + CPM1_PIO_B: gpio-controller@ab8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-b"; + reg = <0xab8 0x10>; + gpio-controller; + }; + + CPM1_PIO_E: gpio-controller@ac8 { + #gpio-cells = <2>; + compatible = "fsl,cpm1-pario-bank-e"; + reg = <0xac8 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt new file mode 100644 index 0000000..0e42694 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/network.txt @@ -0,0 +1,45 @@ +* Network + +Currently defined compatibles: +- fsl,cpm1-scc-enet +- fsl,cpm2-scc-enet +- fsl,cpm1-fec-enet +- fsl,cpm2-fcc-enet (third resource is GFEMR) +- fsl,qe-enet + +Example: + + ethernet@11300 { + device_type = "network"; + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <11300 20 8400 100 11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY0>; + fsl,cpm-command = <12000300>; + }; + +* MDIO + +Currently defined compatibles: +fsl,pq1-fec-mdio (reg is same as first resource of FEC device) +fsl,cpm2-mdio-bitbang (reg is port C registers) + +Properties for fsl,cpm2-mdio-bitbang: +fsl,mdio-pin : pin of port C controlling mdio data +fsl,mdc-pin : pin of port C controlling mdio clock + +Example: + mdio@10d40 { + device_type = "mdio"; + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <10d40 14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt new file mode 100644 index 0000000..4f89302 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe.txt @@ -0,0 +1,115 @@ +* Freescale QUICC Engine module (QE) +This represents qe module that is installed on PowerQUICC II Pro. + +NOTE: This is an interim binding; it should be updated to fit +in with the CPM binding later in this document. + +Basically, it is a bus of devices, that could act more or less +as a complete entity (UCC, USB etc ). All of them should be siblings on +the "root" qe node, using the common properties from there. +The description below applies to the qe of MPC8360 and +more nodes and properties would be extended in the future. + +i) Root QE device + +Required properties: +- compatible : should be "fsl,qe"; +- model : precise model of the QE, Can be "QE", "CPM", or "CPM2" +- reg : offset and length of the device registers. +- bus-frequency : the clock frequency for QUICC Engine. +- fsl,qe-num-riscs: define how many RISC engines the QE has. +- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the + threads. + +Optional properties: +- fsl,firmware-phandle: + Usage: required only if there is no fsl,qe-firmware child node + Value type: <phandle> + Definition: Points to a firmware node (see "QE Firmware Node" below) + that contains the firmware that should be uploaded for this QE. + The compatible property for the firmware node should say, + "fsl,qe-firmware". + +Recommended properties +- brg-frequency : the internal clock source frequency for baud-rate + generators in Hz. + +Example: + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + compatible = "fsl,qe"; + ranges = <0 e0100000 00100000>; + reg = <e0100000 480>; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + } + +* Multi-User RAM (MURAM) + +Required properties: +- compatible : should be "fsl,qe-muram", "fsl,cpm-muram". +- mode : the could be "host" or "slave". +- ranges : Should be defined as specified in 1) to describe the + translation of MURAM addresses. +- data-only : sub-node which defines the address area under MURAM + bus that can be allocated as data/parameter + +Example: + + muram@10000 { + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0 c000>; + }; + }; + +* QE Firmware Node + +This node defines a firmware binary that is embedded in the device tree, for +the purpose of passing the firmware from bootloader to the kernel, or from +the hypervisor to the guest. + +The firmware node itself contains the firmware binary contents, a compatible +property, and any firmware-specific properties. The node should be placed +inside a QE node that needs it. Doing so eliminates the need for a +fsl,firmware-phandle property. Other QE nodes that need the same firmware +should define an fsl,firmware-phandle property that points to the firmware node +in the first QE node. + +The fsl,firmware property can be specified in the DTS (possibly using incbin) +or can be inserted by the boot loader at boot time. + +Required properties: + - compatible + Usage: required + Value type: <string> + Definition: A standard property. Specify a string that indicates what + kind of firmware it is. For QE, this should be "fsl,qe-firmware". + + - fsl,firmware + Usage: required + Value type: <prop-encoded-array>, encoded as an array of bytes + Definition: A standard property. This property contains the firmware + binary "blob". + +Example: + qe1@e0080000 { + compatible = "fsl,qe"; + qe_firmware:qe-firmware { + compatible = "fsl,qe-firmware"; + fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...]; + }; + ... + }; + + qe2@e0090000 { + compatible = "fsl,qe"; + fsl,firmware-phandle = <&qe_firmware>; + ... + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt new file mode 100644 index 0000000..249db3a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/firmware.txt @@ -0,0 +1,24 @@ +* Uploaded QE firmware + + If a new firmware has been uploaded to the QE (usually by the + boot loader), then a 'firmware' child node should be added to the QE + node. This node provides information on the uploaded firmware that + device drivers may need. + + Required properties: + - id: The string name of the firmware. This is taken from the 'id' + member of the qe_firmware structure of the uploaded firmware. + Device drivers can search this string to determine if the + firmware they want is already present. + - extended-modes: The Extended Modes bitfield, taken from the + firmware binary. It is a 64-bit number represented + as an array of two 32-bit numbers. + - virtual-traps: The virtual traps, taken from the firmware binary. + It is an array of 8 32-bit numbers. + +Example: + firmware { + id = "Soft-UART"; + extended-modes = <0 0>; + virtual-traps = <0 0 0 0 0 0 0 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt new file mode 100644 index 0000000..6098426 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/par_io.txt @@ -0,0 +1,51 @@ +* Parallel I/O Ports + +This node configures Parallel I/O ports for CPUs with QE support. +The node should reside in the "soc" node of the tree. For each +device that using parallel I/O ports, a child node should be created. +See the definition of the Pin configuration nodes below for more +information. + +Required properties: +- device_type : should be "par_io". +- reg : offset to the register set and its length. +- num-ports : number of Parallel I/O ports + +Example: +par_io@1400 { + reg = <1400 100>; + #address-cells = <1>; + #size-cells = <0>; + device_type = "par_io"; + num-ports = <7>; + ucc_pin@01 { + ...... + }; + +Note that "par_io" nodes are obsolete, and should not be used for +the new device trees. Instead, each Par I/O bank should be represented +via its own gpio-controller node: + +Required properties: +- #gpio-cells : should be "2". +- compatible : should be "fsl,<chip>-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank". +- reg : offset to the register set and its length. +- gpio-controller : node to identify gpio controllers. + +Example: + qe_pio_a: gpio-controller@1400 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + }; + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt new file mode 100644 index 0000000..c5b4306 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/pincfg.txt @@ -0,0 +1,60 @@ +* Pin configuration nodes + +Required properties: +- linux,phandle : phandle of this node; likely referenced by a QE + device. +- pio-map : array of pin configurations. Each pin is defined by 6 + integers. The six numbers are respectively: port, pin, dir, + open_drain, assignment, has_irq. + - port : port number of the pin; 0-6 represent port A-G in UM. + - pin : pin number in the port. + - dir : direction of the pin, should encode as follows: + + 0 = The pin is disabled + 1 = The pin is an output + 2 = The pin is an input + 3 = The pin is I/O + + - open_drain : indicates the pin is normal or wired-OR: + + 0 = The pin is actively driven as an output + 1 = The pin is an open-drain driver. As an output, the pin is + driven active-low, otherwise it is three-stated. + + - assignment : function number of the pin according to the Pin Assignment + tables in User Manual. Each pin can have up to 4 possible functions in + QE and two options for CPM. + - has_irq : indicates if the pin is used as source of external + interrupts. + +Example: + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt new file mode 100644 index 0000000..e47734b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt @@ -0,0 +1,70 @@ +* UCC (Unified Communications Controllers) + +Required properties: +- device_type : should be "network", "hldc", "uart", "transparent" + "bisync", "atm", or "serial". +- compatible : could be "ucc_geth" or "fsl_atm" and so on. +- cell-index : the ucc number(1-8), corresponding to UCCx in UM. +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- pio-handle : The phandle for the Parallel I/O port configuration. +- port-number : for UART drivers, the port number to use, between 0 and 3. + This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. + The port number is added to the minor number of the device. Unlike the + CPM UART driver, the port-number is required for the QE UART driver. +- soft-uart : for UART drivers, if specified this means the QE UART device + driver should use "Soft-UART" mode, which is needed on some SOCs that have + broken UART hardware. Soft-UART is provided via a microcode upload. +- rx-clock-name: the UCC receive clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- tx-clock-name: the UCC transmit clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +The following two properties are deprecated. rx-clock has been replaced +with rx-clock-name, and tx-clock has been replaced with tx-clock-name. +Drivers that currently use the deprecated properties should continue to +do so, in order to support older device trees, but they should be updated +to check for the new properties first. +- rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + +Required properties for network device_type: +- mac-address : list of bytes representing the ethernet address. +- phy-handle : The phandle for the PHY connected to this controller. + +Recommended properties: +- phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal + Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), + "tbi", or "rtbi". + +Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <2000 200>; + interrupts = <a0 0>; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + phy-connection-type = "gmii"; + pio-handle = <140001>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt new file mode 100644 index 0000000..9ccd5f3 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/usb.txt @@ -0,0 +1,37 @@ +Freescale QUICC Engine USB Controller + +Required properties: +- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb". +- reg : the first two cells should contain usb registers location and + length, the next two two cells should contain PRAM location and + length. +- interrupts : should contain USB interrupt. +- interrupt-parent : interrupt source phandle. +- fsl,fullspeed-clock : specifies the full speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- fsl,lowspeed-clock : specifies the low speed USB clock source: + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- hub-power-budget : USB power budget for the root hub, in mA. +- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP, + USBRN, SPEED (optional), and POWER (optional). + +Example: + +usb@6c0 { + compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb"; + reg = <0x6c0 0x40 0x8b00 0x100>; + interrupts = <11>; + interrupt-parent = <&qeic>; + fsl,fullspeed-clock = "clk21"; + gpios = <&qe_pio_b 2 0 /* USBOE */ + &qe_pio_b 3 0 /* USBTP */ + &qe_pio_b 8 0 /* USBTN */ + &qe_pio_b 9 0 /* USBRP */ + &qe_pio_b 11 0 /* USBRN */ + &qe_pio_e 20 0 /* SPEED */ + &qe_pio_e 21 0 /* POWER */>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt new file mode 100644 index 0000000..2ea76d9 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/serial.txt @@ -0,0 +1,32 @@ +* Serial + +Currently defined compatibles: +- fsl,cpm1-smc-uart +- fsl,cpm2-smc-uart +- fsl,cpm1-scc-uart +- fsl,cpm2-scc-uart +- fsl,qe-uart + +Modem control lines connected to GPIO controllers are listed in the gpios +property as described in booting-without-of.txt, section IX.1 in the following +order: + +CTS, RTS, DCD, DSR, DTR, and RI. + +The gpios property is optional and can be left out when control lines are +not used. + +Example: + + serial@11a00 { + device_type = "serial"; + compatible = "fsl,mpc8272-scc-uart", + "fsl,cpm2-scc-uart"; + reg = <11a00 20 8000 100>; + interrupts = <28 8>; + interrupt-parent = <&PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <00800000>; + gpios = <&gpio_c 15 0 + &gpio_d 29 0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/diu.txt b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt new file mode 100644 index 0000000..b66cb6d --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/diu.txt @@ -0,0 +1,34 @@ +* Freescale Display Interface Unit + +The Freescale DIU is a LCD controller, with proper hardware, it can also +drive DVI monitors. + +Required properties: +- compatible : should be "fsl,diu" or "fsl,mpc5121-diu". +- reg : should contain at least address and length of the DIU register + set. +- interrupts : one DIU interrupt should be described here. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- edid : verbatim EDID data block describing attached display. + Data from the detailed timing descriptor will be used to + program the display controller. + +Example (MPC8610HPCD): + display@2c000 { + compatible = "fsl,diu"; + reg = <0x2c000 100>; + interrupts = <72 2>; + interrupt-parent = <&mpic>; + }; + +Example for MPC5121: + display@2100 { + compatible = "fsl,mpc5121-diu"; + reg = <0x2100 0x100>; + interrupts = <64 0x8>; + interrupt-parent = <&ipic>; + edid = [edid-data]; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt new file mode 100644 index 0000000..2a4b4bc --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -0,0 +1,144 @@ +* Freescale 83xx DMA Controller + +Freescale PowerPC 83xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8349, mpc8360, etc.) and the second is + "fsl,elo-dma" +- reg : <registers mapping for DMA general status reg> +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. +- cell-index : controller index. 0 for controller @ 0x8100 +- interrupts : <interrupt mapping for DMA IRQ> +- interrupt-parent : optional, if needed for interrupt mapping + + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8349, mpc8350, etc.) and the second is + "fsl,elo-dma-channel". However, see note below. + - reg : <registers mapping for channel> + - cell-index : dma channel index starts at 0. + +Optional properties: + - interrupts : <interrupt mapping for DMA channel IRQ> + (on 83xx this is expected to be identical to + the interrupts property of the parent node) + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; + reg = <0x82a8 4>; + ranges = <0 0x8100 0x1a4>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <0>; + reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@80 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <1>; + reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@100 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <2>; + reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@180 { + compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; + cell-index = <3>; + reg = <0x180 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + }; + +* Freescale 85xx/86xx DMA Controller + +Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. + +Required properties: + +- compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma", where CHIP is the processor + (mpc8540, mpc8540, etc.) and the second is + "fsl,eloplus-dma" +- reg : <registers mapping for DMA general status reg> +- cell-index : controller index. 0 for controller @ 0x21000, + 1 for controller @ 0xc000 +- ranges : Should be defined as specified in 1) to describe the + DMA controller channels. + +- DMA channel nodes: + - compatible : compatible list, contains 2 entries, first is + "fsl,CHIP-dma-channel", where CHIP is the processor + (mpc8540, mpc8560, etc.) and the second is + "fsl,eloplus-dma-channel". However, see note below. + - cell-index : dma channel index starts at 0. + - reg : <registers mapping for channel> + - interrupts : <interrupt mapping for DMA channel IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + +Example: + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; + reg = <0x21300 4>; + ranges = <0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + +Note on DMA channel compatible properties: The compatible property must say +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA +driver (fsldma). Any DMA channel used by fsldma cannot be used by another +DMA driver, such as the SSI sound drivers for the MPC8610. Therefore, any DMA +channel that should be used for another driver should not use +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel". For the SSI drivers, for +example, the compatible property should be "fsl,ssi-dma-channel". See ssi.txt +for more information. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt new file mode 100644 index 0000000..f514f29 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ecm.txt @@ -0,0 +1,64 @@ +===================================================================== +E500 LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For ECM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,ecm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +E500 Coherency Module Node + +The E500 LAW node represents the region of CCSR space where ECM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-ecm", "fsl,ecm" where + CHIP is the processor (mpc8572, mpc8544, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt new file mode 100644 index 0000000..9a33efd --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/gtm.txt @@ -0,0 +1,31 @@ +* Freescale General-purpose Timers Module + +Required properties: + - compatible : should be + "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs + "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs + "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs + - reg : should contain gtm registers location and length (0x40). + - interrupts : should contain four interrupts. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies the frequency driving the timer. + +Example: + +timer@500 { + compatible = "fsl,mpc8360-gtm", "fsl,gtm"; + reg = <0x500 0x40>; + interrupts = <90 8 78 8 84 8 72 8>; + interrupt-parent = <&ipic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; + +timer@440 { + compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; + reg = <0x440 0x40>; + interrupts = <12 13 14 15>; + interrupt-parent = <&qeic>; + /* filled by u-boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt new file mode 100644 index 0000000..9e7a241 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt @@ -0,0 +1,25 @@ +* Global Utilities Block + +The global utilities block controls power management, I/O device +enabling, power-on-reset configuration monitoring, general-purpose +I/O signal configuration, alternate function selection for multiplexed +signals, and clock control. + +Required properties: + + - compatible : Should define the compatible device type for + global-utilities. + - reg : Offset and length of the register set for the device. + +Recommended properties: + + - fsl,has-rstcr : Indicates that the global utilities register set + contains a functioning "reset control register" (i.e. the board + is wired to reset upon setting the HRESET_REQ bit in this register). + +Example: + global-utilities@e0000 { /* global utilities block */ + compatible = "fsl,mpc8548-guts"; + reg = <e0000 1000>; + fsl,has-rstcr; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt new file mode 100644 index 0000000..3300fec --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/lbc.txt @@ -0,0 +1,35 @@ +* Chipselect/Local Bus + +Properties: +- name : Should be localbus +- #address-cells : Should be either two or three. The first cell is the + chipselect number, and the remaining cells are the + offset into the chipselect. +- #size-cells : Either one or two, depending on how large each chipselect + can be. +- ranges : Each range corresponds to a single chipselect, and cover + the entire access window as configured. + +Example: + localbus@f0010100 { + compatible = "fsl,mpc8272-localbus", + "fsl,pq2-localbus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <f0010100 40>; + + ranges = <0 0 fe000000 02000000 + 1 0 f4500000 00008000>; + + flash@0,0 { + compatible = "jedec-flash"; + reg = <0 0 2000000>; + bank-width = <4>; + device-width = <1>; + }; + + board-control@1,0 { + reg = <1 0 20>; + compatible = "fsl,mpc8272ads-bcsr"; + }; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt new file mode 100644 index 0000000..4ceda9b --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcm.txt @@ -0,0 +1,64 @@ +===================================================================== +MPX LAW & Coherency Module Device Tree Binding +Copyright (C) 2009 Freescale Semiconductor Inc. +===================================================================== + +Local Access Window (LAW) Node + +The LAW node represents the region of CCSR space where local access +windows are configured. For MCM based devices this is the first 4k +of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some +number of local access windows as specified by fsl,num-laws. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,mcm-law" + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - fsl,num-laws + Usage: required + Value type: <u32> + Definition: The value specifies the number of local access + windows for this device. + +===================================================================== + +MPX Coherency Module Node + +The MPX LAW node represents the region of CCSR space where MCM config +and error reporting registers exist, this is the second 4k (0x1000) +of CCSR space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,CHIP-mcm", "fsl,mcm" where + CHIP is the processor (mpc8641, mpc8610, etc.) + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The value specifies the + physical address offset and length of the CCSR space + registers. + + - interrupts + Usage: required + Value type: <prop-encoded-array> + + - interrupt-parent + Usage: required + Value type: <phandle> + +===================================================================== diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt new file mode 100644 index 0000000..0f76633 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mcu-mpc8349emitx.txt @@ -0,0 +1,17 @@ +Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU) + +Required properties: +- compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx". +- reg : should specify I2C address (0x0a). +- #gpio-cells : should be 2. +- gpio-controller : should be present. + +Example: + +mcu@0a { + #gpio-cells = <2>; + compatible = "fsl,mc9s08qg8-mpc8349emitx", + "fsl,mcu-mpc8349emitx"; + reg = <0x0a>; + gpio-controller; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt new file mode 100644 index 0000000..8832e87 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt @@ -0,0 +1,70 @@ +MPC5121 PSC Device Tree Bindings + +PSC in UART mode +---------------- + +For PSC in UART mode the needed PSC serial devices +are specified by fsl,mpc5121-psc-uart nodes in the +fsl,mpc5121-immr SoC node. Additionally the PSC FIFO +Controller node fsl,mpc5121-psc-fifo is requered there: + +fsl,mpc5121-psc-uart nodes +-------------------------- + +Required properties : + - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" + - cell-index : Index of the PSC in hardware + - reg : Offset and length of the register set for the PSC device + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Recommended properties : + - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) + - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) + + +fsl,mpc5121-psc-fifo node +------------------------- + +Required properties : + - compatible : Should be "fsl,mpc5121-psc-fifo" + - reg : Offset and length of the register set for the PSC + FIFO Controller + - interrupts : <a b> where a is the interrupt number of the + PSC FIFO Controller and b is a field that represents an + encoding of the sense and level information for the interrupt. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + + +Example for a board using PSC0 and PSC1 devices in serial mode: + +serial@11000 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <0>; + reg = <0x11000 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +serial@11100 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <1>; + reg = <0x11100 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; +}; + +pscfifo@11f00 { + compatible = "fsl,mpc5121-psc-fifo"; + reg = <0x11f00 0x100>; + interrupts = <40 0x8>; + interrupt-parent = < &ipic >; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt new file mode 100644 index 0000000..4ccb2cd --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt @@ -0,0 +1,198 @@ +MPC5200 Device Tree Bindings +---------------------------- + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +Naming conventions +------------------ +For mpc5200 on-chip devices, the format for each compatible value is +<chip>-<device>[-<mode>]. The OS should be able to match a device driver +to the device based solely on the compatible value. If two drivers +match on the compatible list; the 'most compatible' driver should be +selected. + +The split between the MPC5200 and the MPC5200B leaves a bit of a +conundrum. How should the compatible property be set up to provide +maximum compatibility information; but still accurately describe the +chip? For the MPC5200; the answer is easy. Most of the SoC devices +originally appeared on the MPC5200. Since they didn't exist anywhere +else; the 5200 compatible properties will contain only one item; +"fsl,mpc5200-<device>". + +The 5200B is almost the same as the 5200, but not quite. It fixes +silicon bugs and it adds a small number of enhancements. Most of the +devices either provide exactly the same interface as on the 5200. A few +devices have extra functions but still have a backwards compatible mode. +To express this information as completely as possible, 5200B device trees +should have two items in the compatible list: + compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>"; + +It is *strongly* recommended that 5200B device trees follow this convention +(instead of only listing the base mpc5200 item). + +ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec"; + ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec"; + +Modal devices, like PSCs, also append the configured function to the +end of the compatible field. ie. A PSC in i2s mode would specify +"fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to +avoid naming conflicts with non-psc devices providing the same +function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe +the mpc5200 simple spi device and a PSC spi mode respectively. + +At the time of writing, exact chip may be either 'fsl,mpc5200' or +'fsl,mpc5200b'. + +The soc node +------------ +This node describes the on chip SOC peripherals. Every mpc5200 based +board will have this node, and as such there is a common naming +convention for SOC devices. + +Required properties: +name description +---- ----------- +ranges Memory range of the internal memory mapped registers. + Should be <0 [baseaddr] 0xc000> +reg Should be <[baseaddr] 0x100> +compatible mpc5200: "fsl,mpc5200-immr" + mpc5200b: "fsl,mpc5200b-immr" +system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI + clocks are derived from the fsystem clock. +bus-frequency IPB bus frequency in Hz. Clock rate + used by most of the soc devices. + +soc child nodes +--------------- +Any on chip SOC devices available to Linux must appear as soc5200 child nodes. + +Note: The tables below show the value for the mpc5200. A mpc5200b device +tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form. + +Required soc5200 child nodes: +name compatible Description +---- ---------- ----------- +cdm@<addr> fsl,mpc5200-cdm Clock Distribution +interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt + controller to boot +bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller + +Recommended soc5200 child nodes; populate as needed for your board +name compatible Description +---- ---------- ----------- +timer@<addr> fsl,mpc5200-gpt General purpose timers +gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller +gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller +rtc@<addr> fsl,mpc5200-rtc Real time clock +mscan@<addr> fsl,mpc5200-mscan CAN bus controller +pci@<addr> fsl,mpc5200-pci PCI bridge +serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode +i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode +ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode +spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode +irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode +spi@<addr> fsl,mpc5200-spi MPC5200 spi device +ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device +ata@<addr> fsl,mpc5200-ata IDE ATA interface +i2c@<addr> fsl,mpc5200-i2c I2C controller +usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller +xlb@<addr> fsl,mpc5200-xlb XLB arbitrator + +fsl,mpc5200-gpt nodes +--------------------- +On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board +design supports the internal wdt, then the device node for GPT0 should +include the empty property 'fsl,has-wdt'. Note that this does not activate +the watchdog. The timer will function as a GPT if the timer api is used, and +it will function as watchdog if the watchdog device is used. The watchdog +mode has priority over the gpt mode, i.e. if the watchdog is activated, any +gpt api call to this timer will fail with -EBUSY. + +If you add the property + fsl,wdt-on-boot = <n>; +GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. +If n>0, the watchdog is started with a timeout of n seconds. If n=0, the +configuration of the watchdog is not touched. This is useful in two cases: +- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; +- do not touch a configuration assigned by the boot loader which supervises + the boot process itself. + +The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. + +An mpc5200-gpt can be used as a single line GPIO controller. To do so, +add the following properties to the gpt node: + gpio-controller; + #gpio-cells = <2>; +When referencing the GPIO line from another node, the first cell must always +be zero and the second cell represents the gpio flags and described in the +gpio device tree binding. + +An mpc5200-gpt can be used as a single line edge sensitive interrupt +controller. To do so, add the following properties to the gpt node: + interrupt-controller; + #interrupt-cells = <1>; +When referencing the IRQ line from another node, the cell represents the +sense mode; 1 for edge rising, 2 for edge falling. + +fsl,mpc5200-psc nodes +--------------------- +The PSCs should include a cell-index which is the index of the PSC in +hardware. cell-index is used to determine which shared SoC registers to +use when setting up PSC clocking. cell-index number starts at '0'. ie: + PSC1 has 'cell-index = <0>' + PSC4 has 'cell-index = <3>' + +PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in +i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the +compatible field. + + +fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes +------------------------------------------------ +Each GPIO controller node should have the empty property gpio-controller and +#gpio-cells set to 2. First cell is the GPIO number which is interpreted +according to the bit numbers in the GPIO control registers. The second cell +is for flags which is currently unused. + +fsl,mpc5200-fec nodes +--------------------- +The FEC node can specify one of the following properties to configure +the MII link: +- fsl,7-wire-mode - An empty property that specifies the link uses 7-wire + mode instead of MII +- current-speed - Specifies that the MII should be configured for a fixed + speed. This property should contain two cells. The + first cell specifies the speed in Mbps and the second + should be '0' for half duplex and '1' for full duplex +- phy-handle - Contains a phandle to an Ethernet PHY. + +Interrupt controller (fsl,mpc5200-pic) node +------------------------------------------- +The mpc5200 pic binding splits hardware IRQ numbers into two levels. The +split reflects the layout of the PIC hardware itself, which groups +interrupts into one of three groups; CRIT, MAIN or PERP. Also, the +Bestcomm dma engine has it's own set of interrupt sources which are +cascaded off of peripheral interrupt 0, which the driver interprets as a +fourth group, SDMA. + +The interrupts property for device nodes using the mpc5200 pic consists +of three cells; <L1 L2 level> + + L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3] + L2 := interrupt number; directly mapped from the value in the + "ICTL PerStat, MainStat, CritStat Encoded Register" + level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3] + +For external IRQs, use the following interrupt property values (how to +specify external interrupts is a frequently asked question): +External interrupts: + external irq0: interrupts = <0 0 n>; + external irq1: interrupts = <1 1 n>; + external irq2: interrupts = <1 2 n>; + external irq3: interrupts = <1 3 n>; +'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) + +fsl,mpc5200-mscan nodes +----------------------- +See file can.txt in this directory. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt new file mode 100644 index 0000000..71e39cf --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt @@ -0,0 +1,42 @@ +* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores + +The OpenPIC specification does not specify which interrupt source has to +become which interrupt number. This is up to the software implementation +of the interrupt controller. The only requirement is that every +interrupt source has to have an unique interrupt number / vector number. +To accomplish this the current implementation assigns the number zero to +the first source, the number one to the second source and so on until +all interrupt sources have their unique number. +Usually the assigned vector number equals the interrupt number mentioned +in the documentation for a given core / CPU. This is however not true +for the e500 cores (MPC85XX CPUs) where the documentation distinguishes +between internal and external interrupt sources and starts counting at +zero for both of them. + +So what to write for external interrupt source X or internal interrupt +source Y into the device tree? Here is an example: + +The memory map for the interrupt controller in the MPC8544[0] shows, +that the first interrupt source starts at 0x5_0000 (PIC Register Address +Map-Interrupt Source Configuration Registers). This source becomes the +number zero therefore: + External interrupt 0 = interrupt number 0 + External interrupt 1 = interrupt number 1 + External interrupt 2 = interrupt number 2 + ... +Every interrupt number allocates 0x20 bytes register space. So to get +its number it is sufficient to shift the lower 16bits to right by five. +So for the external interrupt 10 we have: + 0x0140 >> 5 = 10 + +After the external sources, the internal sources follow. The in core I2C +controller on the MPC8544 for instance has the internal source number +27. Oo obtain its interrupt number we take the lower 16bits of its memory +address (0x5_0560) and shift it right: + 0x0560 >> 5 = 43 + +Therefore the I2C device node for the MPC8544 CPU has to have the +interrupt number 43 specified in the device tree. + +[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual + MPC8544ERM Rev. 1 10/2007 diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt new file mode 100644 index 0000000..bcc30ba --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt @@ -0,0 +1,36 @@ +* Freescale MSI interrupt controller + +Required properties: +- compatible : compatible list, contains 2 entries, + first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, + etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on + the parent type. +- reg : should contain the address and the length of the shared message + interrupt register set. +- msi-available-ranges: use <start count> style section to define which + msi interrupt can be used in the 256 msi interrupts. This property is + optional, without this, all the 256 MSI interrupts can be used. +- interrupts : each one of the interrupts here is one entry per 32 MSIs, + and routed to the host interrupt controller. the interrupts should + be set as edge sensitive. +- interrupt-parent: the phandle for the interrupt controller + that services interrupts for this device. for 83xx cpu, the interrupts + are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed + to MPIC. + +Example: + msi@41600 { + compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt new file mode 100644 index 0000000..07256b7 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/pmc.txt @@ -0,0 +1,63 @@ +* Power Management Controller + +Properties: +- compatible: "fsl,<chip>-pmc". + + "fsl,mpc8349-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8313-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8548-pmc" should be listed for any chip whose PMC is + compatible. "fsl,mpc8536-pmc" should also be listed for any chip + whose PMC is compatible, and implies deep-sleep capability. + + "fsl,mpc8641d-pmc" should be listed for any chip whose PMC is + compatible; all statements below that apply to "fsl,mpc8548-pmc" also + apply to "fsl,mpc8641d-pmc". + + Compatibility does not include bit assignments in SCCR/PMCDR/DEVDISR; these + bit assignments are indicated via the sleep specifier in each device's + sleep property. + +- reg: For devices compatible with "fsl,mpc8349-pmc", the first resource + is the PMC block, and the second resource is the Clock Configuration + block. + + For devices compatible with "fsl,mpc8548-pmc", the first resource + is a 32-byte block beginning with DEVDISR. + +- interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first + resource is the PMC block interrupt. + +- fsl,mpc8313-wakeup-timer: For "fsl,mpc8313-pmc"-compatible devices, + this is a phandle to an "fsl,gtm" node on which timer 4 can be used as + a wakeup source from deep sleep. + +Sleep specifiers: + + fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit + that is set in the cell, the corresponding bit in SCCR will be saved + and cleared on suspend, and restored on resume. This sleep controller + supports disabling and resuming devices at any time. + + fsl,mpc8536-pmc: Sleep specifiers consist of three cells, the third of + which will be ORed into PMCDR upon suspend, and cleared from PMCDR + upon resume. The first two cells are as described for fsl,mpc8578-pmc. + This sleep controller only supports disabling devices during system + sleep, or permanently. + + fsl,mpc8548-pmc: Sleep specifiers consist of one or two cells, the + first of which will be ORed into DEVDISR (and the second into + DEVDISR2, if present -- this cell should be zero or absent if the + hardware does not have DEVDISR2) upon a request for permanent device + disabling. This sleep controller does not support configuring devices + to disable during system sleep (unless supported by another compatible + match), or dynamically. + +Example: + + power@b00 { + compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc"; + reg = <0xb00 0x100 0xa00 0x100>; + interrupts = <80 8>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/sec.txt b/Documentation/devicetree/bindings/powerpc/fsl/sec.txt new file mode 100644 index 0000000..2b6f2d4 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/sec.txt @@ -0,0 +1,68 @@ +Freescale SoC SEC Security Engines + +Required properties: + +- compatible : Should contain entries for this and backward compatible + SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0" +- reg : Offset and length of the register set for the device +- interrupts : the SEC's interrupt number +- fsl,num-channels : An integer representing the number of channels + available. +- fsl,channel-fifo-len : An integer representing the number of + descriptor pointers each channel fetch fifo can hold. +- fsl,exec-units-mask : The bitmask representing what execution units + (EUs) are available. It's a single 32-bit cell. EU information + should be encoded following the SEC's Descriptor Header Dword + EU_SEL0 field documentation, i.e. as follows: + + bit 0 = reserved - should be 0 + bit 1 = set if SEC has the ARC4 EU (AFEU) + bit 2 = set if SEC has the DES/3DES EU (DEU) + bit 3 = set if SEC has the message digest EU (MDEU/MDEU-A) + bit 4 = set if SEC has the random number generator EU (RNG) + bit 5 = set if SEC has the public key EU (PKEU) + bit 6 = set if SEC has the AES EU (AESU) + bit 7 = set if SEC has the Kasumi EU (KEU) + bit 8 = set if SEC has the CRC EU (CRCU) + bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B) + +remaining bits are reserved for future SEC EUs. + +- fsl,descriptor-types-mask : The bitmask representing what descriptors + are available. It's a single 32-bit cell. Descriptor type information + should be encoded following the SEC's Descriptor Header Dword DESC_TYPE + field documentation, i.e. as follows: + + bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type + bit 1 = set if SEC supports the ipsec_esp descriptor type + bit 2 = set if SEC supports the common_nonsnoop desc. type + bit 3 = set if SEC supports the 802.11i AES ccmp desc. type + bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type + bit 5 = set if SEC supports the srtp descriptor type + bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type + bit 7 = set if SEC supports the pkeu_assemble descriptor type + bit 8 = set if SEC supports the aesu_key_expand_output desc.type + bit 9 = set if SEC supports the pkeu_ptmul descriptor type + bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type + bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type + + ..and so on and so forth. + +Optional properties: + +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Example: + + /* MPC8548E */ + crypto@30000 { + compatible = "fsl,sec2.1", "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <29 2>; + interrupt-parent = <&mpic>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0xfe>; + fsl,descriptor-types-mask = <0x12b0ebf>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt new file mode 100644 index 0000000..5ff76c9 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt @@ -0,0 +1,73 @@ +Freescale Synchronous Serial Interface + +The SSI is a serial device that communicates with audio codecs. It can +be programmed in AC97, I2S, left-justified, or right-justified modes. + +Required properties: +- compatible: Compatible list, contains "fsl,ssi". +- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. +- reg: Offset and length of the register set for the device. +- interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and + level information for the interrupt. This should be + encoded based on the information in section 2) + depending on the type of interrupt controller you + have. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this device. +- fsl,mode: The operating mode for the SSI interface. + "i2s-slave" - I2S mode, SSI is clock slave + "i2s-master" - I2S mode, SSI is clock master + "lj-slave" - left-justified mode, SSI is clock slave + "lj-master" - l.j. mode, SSI is clock master + "rj-slave" - right-justified mode, SSI is clock slave + "rj-master" - r.j., SSI is clock master + "ac97-slave" - AC97 mode, SSI is clock slave + "ac97-master" - AC97 mode, SSI is clock master +- fsl,playback-dma: Phandle to a node for the DMA channel to use for + playback of audio. This is typically dictated by SOC + design. See the notes below. +- fsl,capture-dma: Phandle to a node for the DMA channel to use for + capture (recording) of audio. This is typically dictated + by SOC design. See the notes below. +- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. + This number is the maximum allowed value for SFCSR[TFWM0]. +- fsl,ssi-asynchronous: + If specified, the SSI is to be programmed in asynchronous + mode. In this mode, pins SRCK, STCK, SRFS, and STFS must + all be connected to valid signals. In synchronous mode, + SRCK and SRFS are ignored. Asynchronous mode allows + playback and capture to use different sample sizes and + sample rates. Some drivers may require that SRCK and STCK + be connected together, and SRFS and STFS be connected + together. This would still allow different sample sizes, + but not different sample rates. + +Optional properties: +- codec-handle: Phandle to a 'codec' node that defines an audio + codec connected to this SSI. This node is typically + a child of an I2C or other control node. + +Child 'codec' node required properties: +- compatible: Compatible list, contains the name of the codec + +Child 'codec' node optional properties: +- clock-frequency: The frequency of the input clock, which typically comes + from an on-board dedicated oscillator. + +Notes on fsl,playback-dma and fsl,capture-dma: + +On SOCs that have an SSI, specific DMA channels are hard-wired for playback +and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for +playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for +playback and DMA channel 3 for capture. The developer can choose which +DMA controller to use, but the channels themselves are hard-wired. The +purpose of these two properties is to represent this hardware design. + +The device tree nodes for the DMA channels that are referenced by +"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with +"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. +"fsl,mpc8610-dma-channel") can remain. If these nodes are left as +"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA +drivers (fsldma) will attempt to use them, and it will conflict with the +sound drivers. |
