diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
8 files changed, 351 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt new file mode 100644 index 0000000..0a85c70 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -0,0 +1,68 @@ +* Atmel High Speed MultiMedia Card Interface + +This controller on atmel products provides an interface for MMC, SD and SDIO +types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the atmel-mci driver. + +1) MCI node + +Required properties: +- compatible: should be "atmel,hsmci" +- #address-cells: should be one. The cell is the slot id. +- #size-cells: should be zero. +- at least one slot node + +The node contains child nodes for each slot that the platform uses + +Example MCI node: + +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + + [ child node definitions...] +}; + +2) slot nodes + +Required properties: +- reg: should contain the slot id. +- bus-width: number of data lines connected to the controller + +Optional properties: +- cd-gpios: specify GPIOs for card detection +- cd-inverted: invert the value of external card detect gpio line +- wp-gpios: specify GPIOs for write protection + +Example slot node: + +slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; +}; + +Example full MCI node: +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; + }; + slot@1 { + reg = <1>; + bus-width = <4>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt new file mode 100644 index 0000000..7927689 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -0,0 +1,87 @@ +* Samsung Exynos specific extensions to the Synopsis Designware Mobile + Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsis dw mshc controller properties described +by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific +extensions to the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210 + specific extentions. + - "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412 + specific extentions. + - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250 + specific extentions. + +* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface + unit (ciu) clock. This property is applicable only for Exynos5 SoC's and + ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7. + +* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for single + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + +* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for double + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + + Notes for the sdr-timing and ddr-timing values: + + The order of the cells should be + - First Cell: CIU clock phase shift value for tx mode. + - Second Cell: CIU clock phase shift value for rx mode. + + Valid values for SDR and DDR CIU clock timing for Exynos5250: + - valid value for tx phase shift and rx phase shift is 0 to 7. + - when CIU clock divider value is set to 3, all possible 8 phase shift + values can be used. + - if CIU clock divider value is 0 (that is divide by 1), both tx and rx + phase shift clocks should be 0. + +Required properties for a slot: + +* gpios: specifies a list of gpios used for command, clock and data bus. The + first gpio is the command line and the second gpio is the clock line. The + rest of the gpios (depending on the bus-width property) are the data lines in + no particular order. The format of the gpio specifier depends on the gpio + controller. + +Example: + + The MSHC controller node can be split into two portions, SoC specific and + board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + + slot@0 { + reg = <0>; + bus-width = <8>; + gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>, + <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>, + <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>, + <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>, + <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8a6811f..8e2e0ba 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -9,12 +9,17 @@ Interpreted by the OF core: Required properties: - bus-width: Number of data lines, can be <1>, <4>, or <8> +Card detection: +If no property below is supplied, standard SDHCI card detect is used. +Only one of the properties in this section should be supplied: + - broken-cd: There is no card detection available; polling must be used. + - cd-gpios: Specify GPIOs for card detection, see gpio binding + - non-removable: non-removable slot (like eMMC); assume always present. + Optional properties: -- cd-gpios: Specify GPIOs for card detection, see gpio binding - wp-gpios: Specify GPIOs for write protection, see gpio binding - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted -- non-removable: non-removable slot (like eMMC) - max-frequency: maximum operating clock frequency Example: diff --git a/Documentation/devicetree/bindings/mmc/pxa-mmc.txt b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt new file mode 100644 index 0000000..b7025de --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt @@ -0,0 +1,25 @@ +* PXA MMC drivers + +Driver bindings for the PXA MCI (MMC/SDIO) interfaces + +Required properties: +- compatible: Should be "marvell,pxa-mmc". +- vmmc-supply: A regulator for VMMC + +Optional properties: +- marvell,detect-delay-ms: sets the detection delay timeout in ms. +- marvell,gpio-power: GPIO spec for the card power enable pin + +This file documents differences between the core properties in mmc.txt +and the properties used by the pxa-mmc driver. + +Examples: + +mmc0: mmc@41100000 { + compatible = "marvell,pxa-mmc"; + reg = <0x41100000 0x1000>; + interrupts = <23>; + cd-gpios = <&gpio 23 0>; + wp-gpios = <&gpio 24 0>; +}; + diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt new file mode 100644 index 0000000..630a7d7 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -0,0 +1,53 @@ +* Samsung's SDHCI Controller device tree bindings + +Samsung's SDHCI controller is used as a connectivity interface with external +MMC, SD and eMMC storage mediums. This file documents differences between the +core mmc properties described by mmc.txt and the properties used by the +Samsung implmentation of the SDHCI controller. + +Note: The mmc core bindings documentation states that if none of the core +card-detect bindings are used, then the standard sdhci card detect mechanism +is used. The Samsung's SDHCI controller bindings extends this as listed below. + +[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the + "Optional Board Specific Properties" section below. + +[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property + is not specified, it is assumed that there is no card detection + mechanism used. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci + controller. + - "samsung,exynos4210-sdhci": For controllers compatible with Exynos4 sdhci + controller. + +Required Board Specific Properties: +- gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. + +Optional Board Specific Properties: +- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed + through a pinmux to the card-detect pin of the card slot. This property + should be used only if none of the mmc core card-detect properties are + used. + +Example: + sdhci@12530000 { + compatible = "samsung,exynos4210-sdhci"; + reg = <0x12530000 0x100>; + interrupts = <0 75 0>; + bus-width = <4>; + cd-gpios = <&gpk2 2 2 3 3>; + gpios = <&gpk2 0 2 0 3>, /* clock line */ + <&gpk2 1 2 0 3>, /* command line */ + <&gpk2 3 2 3 3>, /* data line 0 */ + <&gpk2 4 2 3 3>, /* data line 1 */ + <&gpk2 5 2 3 3>, /* data line 2 */ + <&gpk2 6 2 3 3>; /* data line 3 */ + }; + + Note: This example shows both SoC specific and board specific properties + in a single device node. The properties can be actually be seperated + into SoC specific node and board specific node. diff --git a/Documentation/devicetree/bindings/mmc/sdhci-dove.txt b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt new file mode 100644 index 0000000..ae9aab9 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt @@ -0,0 +1,14 @@ +* Marvell sdhci-dove controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. + +- compatible: Should be "marvell,dove-sdhci". + +Example: + +sdio0: sdio@92000 { + compatible = "marvell,dove-sdhci"; + reg = <0x92000 0x100>; + interrupts = <35>; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-spear.txt b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt new file mode 100644 index 0000000..fd3643e --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt @@ -0,0 +1,18 @@ +* SPEAr SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-spear driver. + +Required properties: +- compatible: "st,spear300-sdhci" + +Optional properties: +- cd-gpios: card detect gpio, with zero flags. + +Example: + + sdhci@fc000000 { + compatible = "st,spear300-sdhci"; + reg = <0xfc000000 0x1000>; + cd-gpios = <&gpio0 6 0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt new file mode 100644 index 0000000..06cd32d08 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt @@ -0,0 +1,79 @@ +* Synopsis Designware Mobile Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core mmc properties described by mmc.txt and the +properties used by the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - snps,dw-mshc: for controllers compliant with synopsis dw-mshc. +* #address-cells: should be 1. +* #size-cells: should be 0. + +# Slots: The slot specific information are contained within child-nodes with + each child-node representing a supported slot. There should be atleast one + child node representing a card slot. The name of the child node representing + the slot is recommended to be slot@n where n is the unique number of the slot + connnected to the controller. The following are optional properties which + can be included in the slot child node. + + * reg: specifies the physical slot number. The valid values of this + property is 0 to (num-slots -1), where num-slots is the value + specified by the num-slots property. + + * bus-width: as documented in mmc core bindings. + + * wp-gpios: specifies the write protect gpio line. The format of the + gpio specifier depends on the gpio controller. If the write-protect + line is not available, this property is optional. + +Optional properties: + +* num-slots: specifies the number of slots supported by the controller. + The number of physical slots actually used could be equal or less than the + value specified by num-slots. If this property is not specified, the value + of num-slot property is assumed to be 1. + +* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not + specified, the default value of the fifo size is determined from the + controller registers. + +* card-detect-delay: Delay in milli-seconds before detecting card after card + insert event. The default value is 0. + +* supports-highspeed: Enables support for high speed cards (upto 50MHz) + +* broken-cd: as documented in mmc core bindings. + +Aliases: + +- All the MSHC controller nodes should be represented in the aliases node using + the following format 'mshc{n}' where n is a unique number for the alias. + +Example: + +The MSHC controller node can be split into two portions, SoC specific and +board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "snps,dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + + slot@0 { + reg = <0>; + bus-width = <8>; + }; + }; |
