3 files changed, 58 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/mfd/bfticu.txt b/Documentation/devicetree/bindings/mfd/bfticu.txt
new file mode 100644
index 0000000..65c9077
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/bfticu.txt
@@ -0,0 +1,25 @@
+KEYMILE bfticu Chassis Management FPGA
+
+The bfticu is a multifunction device that manages the whole chassis.
+Its main functionality is to collect IRQs from the whole chassis and signals
+them to a single controller.
+
+Required properties:
+- compatible: "keymile,bfticu"
+- interrupt-controller: the bfticu FPGA is an interrupt controller
+- interrupts: the main IRQ line to signal the collected IRQs
+- #interrupt-cells : is 2 and their usage is compliant to the 2 cells variant
+  of Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+- interrupt-parent: the parent IRQ ctrl the main IRQ is connected to
+- reg: access on the parent local bus (chip select, offset in chip select, size)
+
+Example:
+
+	chassis-mgmt@3,0 {
+		compatible = "keymile,bfticu";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <3 0 0x100>;
+		interrupt-parent = <&mpic>;
+		interrupts = <6 1 0 0>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/qriox.txt b/Documentation/devicetree/bindings/mfd/qriox.txt
new file mode 100644
index 0000000..f301e2d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qriox.txt
@@ -0,0 +1,17 @@
+KEYMILE qrio Board Control CPLD
+
+The qrio is a multifunction device that controls the KEYMILE boards based on
+the kmp204x design.
+It is consists of a reset controller, watchdog timer, LEDs, and 2 IRQ capable
+GPIO blocks.
+
+Required properties:
+- compatible: "keymile,qriox"
+- reg: access on the parent local bus (chip select, offset in chip select, size)
+
+Example:
+
+	board-control@1,0 {
+		compatible = "keymile,qriox";
+		reg = <1 0 0x80>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
index 8e15ec3..b9ee7b9 100644
--- a/Documentation/devicetree/bindings/mfd/twl4030-power.txt
+++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
@@ -5,7 +5,22 @@ to control the power resources, including power scripts. For now, the
 binding only supports the complete shutdown of the system after poweroff.
 
 Required properties:
-- compatible : must be "ti,twl4030-power"
+- compatible : must be one of the following
+	"ti,twl4030-power"
+	"ti,twl4030-power-reset"
+	"ti,twl4030-power-idle"
+	"ti,twl4030-power-idle-osc-off"
+
+The use of ti,twl4030-power-reset is recommended at least on
+3530 that needs a special configuration for warm reset to work.
+
+When using ti,twl4030-power-idle, the TI recommended configuration
+for idle modes is loaded to the tlw4030 PMIC.
+
+When using ti,twl4030-power-idle-osc-off, the TI recommended
+configuration is used with the external oscillator being shut
+down during off-idle. Note that this does not work on all boards
+depending on how the external oscillator is wired.
 
 Optional properties:
 - ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or