diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
4 files changed, 81 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt new file mode 100644 index 0000000..cc26080 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt @@ -0,0 +1,22 @@ +* Generic 8-bits shift register GPIO driver + +Required properties: +- compatible : Should be "fairchild,74hc595" +- reg : chip select number +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- registers-number: Number of daisy-chained shift registers + +Example: + +gpio5: gpio5@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <4>; + spi-max-frequency = <100000>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-adnp.txt b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt new file mode 100644 index 0000000..af66b27 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt @@ -0,0 +1,34 @@ +Avionic Design N-bit GPIO expander bindings + +Required properties: +- compatible: should be "ad,gpio-adnp" +- reg: The I2C slave address for this device. +- interrupt-parent: phandle of the parent interrupt controller. +- interrupts: Interrupt specifier for the controllers interrupt. +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + - bit 0: polarity (0: normal, 1: inverted) +- gpio-controller: Marks the device as a GPIO controller +- nr-gpios: The number of pins supported by the controller. + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier as described in +Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + +Example: + + gpioext: gpio-controller@41 { + compatible = "ad,gpio-adnp"; + reg = <0x41>; + + interrupt-parent = <&gpio>; + interrupts = <160 1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + nr-gpios = <64>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt new file mode 100644 index 0000000..f4dc523 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt @@ -0,0 +1,24 @@ +VIA/Wondermedia VT8500 GPIO Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-gpio", "wm,wm8505-gpio" + or "wm,wm8650-gpio" depending on your SoC +- reg : Should contain 1 register range (address and length) +- #gpio-cells : should be <3>. + 1) bank + 2) pin number + 3) flags - should be 0 + +Example: + + gpio: gpio-controller@d8110000 { + compatible = "via,vt8500-gpio"; + gpio-controller; + reg = <0xd8110000 0x10000>; + #gpio-cells = <3>; + }; + + vibrate { + gpios = <&gpio 0 1 0>; /* Bank 0, Pin 1, No flags */ + }; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 9bb308a..edc83c1 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -8,7 +8,7 @@ node's name represents the name of the corresponding LED. LED sub-node properties: - gpios : Should specify the LED's GPIO, see "gpios property" in - Documentation/devicetree/gpio.txt. Active low LEDs should be + Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs should be indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). |