diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio/gpio.txt')
-rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio.txt | 60 |
1 files changed, 52 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 0c85bb6..3fb8f53 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -13,11 +13,11 @@ properties, each containing a 'gpio-list': gpio-specifier : Array of #gpio-cells specifying specific gpio (controller specific) -GPIO properties should be named "[<name>-]gpios". Exact +GPIO properties should be named "[<name>-]gpios". The exact meaning of each gpios property must be documented in the device tree binding for each device. -For example, the following could be used to describe gpios pins to use +For example, the following could be used to describe GPIO pins used as chip select lines; with chip selects 0, 1 and 3 populated, and chip select 2 left empty: @@ -44,35 +44,79 @@ whether pin is open-drain and whether pin is logically inverted. Exact meaning of each specifier cell is controller specific, and must be documented in the device tree binding for the device. -Example of the node using GPIOs: +Example of a node using GPIOs: node { gpios = <&qe_pio_e 18 0>; }; In this example gpio-specifier is "18 0" and encodes GPIO pin number, -and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. +and GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +1.1) GPIO specifier best practices +---------------------------------- + +A gpio-specifier should contain a flag indicating the GPIO polarity; active- +high or active-low. If it does, the follow best practices should be followed: + +The gpio-specifier's polarity flag should represent the physical level at the +GPIO controller that achieves (or represents, for inputs) a logically asserted +value at the device. The exact definition of logically asserted should be +defined by the binding for the device. If the board inverts the signal between +the GPIO controller and the device, then the gpio-specifier will represent the +opposite physical level than the signal at the device's pin. + +When the device's signal polarity is configurable, the binding for the +device must either: + +a) Define a single static polarity for the signal, with the expectation that +any software using that binding would statically program the device to use +that signal polarity. + +The static choice of polarity may be either: + +a1) (Preferred) Dictated by a binding-specific DT property. + +or: + +a2) Defined statically by the DT binding itself. + +In particular, the polarity cannot be derived from the gpio-specifier, since +that would prevent the DT from separately representing the two orthogonal +concepts of configurable signal polarity in the device, and possible board- +level signal inversion. + +or: + +b) Pick a single option for device signal polarity, and document this choice +in the binding. The gpio-specifier should represent the polarity of the signal +(at the GPIO controller) assuming that the device is configured for this +particular signal polarity choice. If software chooses to program the device +to generate or receive a signal of the opposite polarity, software will be +responsible for correctly interpreting (inverting) the GPIO signal at the GPIO +controller. 2) gpio-controller nodes ------------------------ -Every GPIO controller node must both an empty "gpio-controller" -property, and have #gpio-cells contain the size of the gpio-specifier. +Every GPIO controller node must contain both an empty "gpio-controller" +property, and a #gpio-cells integer property, which indicates the number of +cells in a gpio-specifier. Example of two SOC GPIO banks defined as gpio-controller nodes: qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; reg = <0x1400 0x18>; gpio-controller; + #gpio-cells = <2>; }; qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; reg = <0x1460 0x18>; gpio-controller; + #gpio-cells = <2>; }; 2.1) gpio- and pin-controller interaction |