diff options
274 files changed, 15385 insertions, 8921 deletions
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 91b7049..808c154 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -21,7 +21,8 @@ Required properties: Optional properties: - ti,no_idle_on_suspend: When present, it prevents the PM to idle the module during suspend. - +- ti,no-reset-on-init: When present, the module should not be reset at init +- ti,no-idle-on-init: When present, the module should not be idled at init Example: diff --git a/Documentation/devicetree/bindings/arm/vic.txt b/Documentation/devicetree/bindings/arm/vic.txt index 266716b..dd52721 100644 --- a/Documentation/devicetree/bindings/arm/vic.txt +++ b/Documentation/devicetree/bindings/arm/vic.txt @@ -18,6 +18,15 @@ Required properties: Optional properties: - interrupts : Interrupt source for parent controllers if the VIC is nested. +- valid-mask : A one cell big bit mask of valid interrupt sources. Each bit + represents single interrupt source, starting from source 0 at LSb and ending + at source 31 at MSb. A bit that is set means that the source is wired and + clear means otherwise. If unspecified, defaults to all valid. +- valid-wakeup-mask : A one cell big bit mask of interrupt sources that can be + configured as wake up source for the system. Order of bits is the same as for + valid-mask property. A set bit means that this interrupt source can be + configured as a wake up source for the system. If unspecied, defaults to all + interrupt sources configurable as wake up sources. Example: @@ -26,4 +35,7 @@ Example: interrupt-controller; #interrupt-cells = <1>; reg = <0x60000 0x1000>; + + valid-mask = <0xffffff7f>; + valid-wakeup-mask = <0x0000ff7f>; }; diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt new file mode 100644 index 0000000..c62391f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt @@ -0,0 +1,19 @@ +* Core Divider Clock bindings for Marvell MVEBU SoCs + +The following is a list of provided IDs and clock names on Armada 370/XP: + 0 = nand (NAND clock) + +Required properties: +- compatible : must be "marvell,armada-370-corediv-clock" +- reg : must be the register address of Core Divider control register +- #clock-cells : from common clock binding; shall be set to 1 +- clocks : must be set to the parent's phandle + +Example: + +corediv_clk: corediv-clocks@18740 { + compatible = "marvell,armada-370-corediv-clock"; + reg = <0x18740 0xc>; + #clock-cells = <1>; + clocks = <&pll>; +}; diff --git a/Documentation/devicetree/bindings/crypto/omap-aes.txt b/Documentation/devicetree/bindings/crypto/omap-aes.txt new file mode 100644 index 0000000..fd97176 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/omap-aes.txt @@ -0,0 +1,31 @@ +OMAP SoC AES crypto Module + +Required properties: + +- compatible : Should contain entries for this and backward compatible + AES versions: + - "ti,omap2-aes" for OMAP2. + - "ti,omap3-aes" for OMAP3. + - "ti,omap4-aes" for OMAP4 and AM33XX. + Note that the OMAP2 and 3 versions are compatible (OMAP3 supports + more algorithms) but they are incompatible with OMAP4. +- ti,hwmods: Name of the hwmod associated with the AES module +- reg : Offset and length of the register set for the module +- interrupts : the interrupt-specifier for the AES module. + +Optional properties: +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "tx" and "rx" if present. + +Example: + /* AM335x */ + aes: aes@53500000 { + compatible = "ti,omap4-aes"; + ti,hwmods = "aes"; + reg = <0x53500000 0xa0>; + interrupts = <102>; + dmas = <&edma 6>, + <&edma 5>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/crypto/omap-sham.txt b/Documentation/devicetree/bindings/crypto/omap-sham.txt new file mode 100644 index 0000000..f839acd --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/omap-sham.txt @@ -0,0 +1,28 @@ +OMAP SoC SHA crypto Module + +Required properties: + +- compatible : Should contain entries for this and backward compatible + SHAM versions: + - "ti,omap2-sham" for OMAP2 & OMAP3. + - "ti,omap4-sham" for OMAP4 and AM33XX. + Note that these two versions are incompatible. +- ti,hwmods: Name of the hwmod associated with the SHAM module +- reg : Offset and length of the register set for the module +- interrupts : the interrupt-specifier for the SHAM module. + +Optional properties: +- dmas: DMA specifiers for the rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request name. Should be "rx" if a dma is present. + +Example: + /* AM335x */ + sham: sham@53100000 { + compatible = "ti,omap4-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x200>; + interrupts = <109>; + dmas = <&edma 36>; + dma-names = "rx"; + }; diff --git a/Documentation/devicetree/bindings/hwrng/omap_rng.txt b/Documentation/devicetree/bindings/hwrng/omap_rng.txt new file mode 100644 index 0000000..6a62acd --- /dev/null +++ b/Documentation/devicetree/bindings/hwrng/omap_rng.txt @@ -0,0 +1,22 @@ +OMAP SoC HWRNG Module + +Required properties: + +- compatible : Should contain entries for this and backward compatible + RNG versions: + - "ti,omap2-rng" for OMAP2. + - "ti,omap4-rng" for OMAP4, OMAP5 and AM33XX. + Note that these two versions are incompatible. +- ti,hwmods: Name of the hwmod associated with the RNG module +- reg : Offset and length of the register set for the module +- interrupts : the interrupt number for the RNG module. + Only used for "ti,omap4-rng". + +Example: +/* AM335x */ +rng: rng@48310000 { + compatible = "ti,omap4-rng"; + ti,hwmods = "rng"; + reg = <0x48310000 0x2000>; + interrupts = <111>; +}; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index ed271fc..8c8908a 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -20,8 +20,29 @@ ti,dual-volt: boolean, supports dual voltage cards ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed +dmas: List of DMA specifiers with the controller specific format +as described in the generic DMA client binding. A tx and rx +specifier is required. +dma-names: List of DMA request names. These strings correspond +1:1 with the DMA specifiers listed in dmas. The string naming is +to be "rx" and "tx" for RX and TX DMA requests, respectively. + +Examples: + +[hwmod populated DMA resources] + + mmc1: mmc@0x4809c000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + ti,dual-volt; + bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + ti,non-removable; + }; + +[generic DMA request binding] -Example: mmc1: mmc@0x4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; @@ -30,4 +51,7 @@ Example: bus-width = <4>; vmmc-supply = <&vmmc>; /* phandle to regulator node */ ti,non-removable; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt index 3077370..1e70a8a 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt @@ -59,16 +59,16 @@ Required subnode-properties: Optional subnode-properties: - fsl,drive-strength: Integer. - 0: 4 mA - 1: 8 mA - 2: 12 mA - 3: 16 mA + 0: MXS_DRIVE_4mA + 1: MXS_DRIVE_8mA + 2: MXS_DRIVE_12mA + 3: MXS_DRIVE_16mA - fsl,voltage: Integer. - 0: 1.8 V - 1: 3.3 V + 0: MXS_VOLTAGE_LOW - 1.8 V + 1: MXS_VOLTAGE_HIGH - 3.3 V - fsl,pull-up: Integer. - 0: Disable the internal pull-up - 1: Enable the internal pull-up + 0: MXS_PULL_DISABLE - Disable the internal pull-up + 1: MXS_PULL_ENABLE - Enable the internal pull-up Note that when enabling the pull-up, the internal pad keeper gets disabled. Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up @@ -85,23 +85,32 @@ pinctrl@80018000 { mmc0_8bit_pins_a: mmc0-8bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2000 0x2010 0x2020 0x2030 - 0x2040 0x2050 0x2060 0x2070 - 0x2080 0x2090 0x20a0>; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + MX28_PAD_SSP0_DATA0__SSP0_D0 + MX28_PAD_SSP0_DATA1__SSP0_D1 + MX28_PAD_SSP0_DATA2__SSP0_D2 + MX28_PAD_SSP0_DATA3__SSP0_D3 + MX28_PAD_SSP0_DATA4__SSP0_D4 + MX28_PAD_SSP0_DATA5__SSP0_D5 + MX28_PAD_SSP0_DATA6__SSP0_D6 + MX28_PAD_SSP0_DATA7__SSP0_D7 + MX28_PAD_SSP0_CMD__SSP0_CMD + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + MX28_PAD_SSP0_SCK__SSP0_SCK + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mmc_cd_cfg: mmc-cd-cfg { - fsl,pinmux-ids = <0x2090>; - fsl,pull-up = <0>; + fsl,pinmux-ids = <MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; mmc_sck_cfg: mmc-sck-cfg { - fsl,pinmux-ids = <0x20a0>; - fsl,drive-strength = <2>; - fsl,pull-up = <0>; + fsl,pinmux-ids = <MX28_PAD_SSP0_SCK__SSP0_SCK>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; @@ -112,811 +121,7 @@ adjusting the configuration for pins card-detection and clock from what group node mmc0-8bit defines. Only the configuration properties to be adjusted need to be listed in the config nodes. -Valid values for i.MX28 pinmux-id: - -pinmux id ------- -- -MX28_PAD_GPMI_D00__GPMI_D0 0x0000 -MX28_PAD_GPMI_D01__GPMI_D1 0x0010 -MX28_PAD_GPMI_D02__GPMI_D2 0x0020 -MX28_PAD_GPMI_D03__GPMI_D3 0x0030 -MX28_PAD_GPMI_D04__GPMI_D4 0x0040 -MX28_PAD_GPMI_D05__GPMI_D5 0x0050 -MX28_PAD_GPMI_D06__GPMI_D6 0x0060 -MX28_PAD_GPMI_D07__GPMI_D7 0x0070 -MX28_PAD_GPMI_CE0N__GPMI_CE0N 0x0100 -MX28_PAD_GPMI_CE1N__GPMI_CE1N 0x0110 -MX28_PAD_GPMI_CE2N__GPMI_CE2N 0x0120 -MX28_PAD_GPMI_CE3N__GPMI_CE3N 0x0130 -MX28_PAD_GPMI_RDY0__GPMI_READY0 0x0140 -MX28_PAD_GPMI_RDY1__GPMI_READY1 0x0150 -MX28_PAD_GPMI_RDY2__GPMI_READY2 0x0160 -MX28_PAD_GPMI_RDY3__GPMI_READY3 0x0170 -MX28_PAD_GPMI_RDN__GPMI_RDN 0x0180 -MX28_PAD_GPMI_WRN__GPMI_WRN 0x0190 -MX28_PAD_GPMI_ALE__GPMI_ALE 0x01a0 -MX28_PAD_GPMI_CLE__GPMI_CLE 0x01b0 -MX28_PAD_GPMI_RESETN__GPMI_RESETN 0x01c0 -MX28_PAD_LCD_D00__LCD_D0 0x1000 -MX28_PAD_LCD_D01__LCD_D1 0x1010 -MX28_PAD_LCD_D02__LCD_D2 0x1020 -MX28_PAD_LCD_D03__LCD_D3 0x1030 -MX28_PAD_LCD_D04__LCD_D4 0x1040 -MX28_PAD_LCD_D05__LCD_D5 0x1050 -MX28_PAD_LCD_D06__LCD_D6 0x1060 -MX28_PAD_LCD_D07__LCD_D7 0x1070 -MX28_PAD_LCD_D08__LCD_D8 0x1080 -MX28_PAD_LCD_D09__LCD_D9 0x1090 -MX28_PAD_LCD_D10__LCD_D10 0x10a0 -MX28_PAD_LCD_D11__LCD_D11 0x10b0 -MX28_PAD_LCD_D12__LCD_D12 0x10c0 -MX28_PAD_LCD_D13__LCD_D13 0x10d0 -MX28_PAD_LCD_D14__LCD_D14 0x10e0 -MX28_PAD_LCD_D15__LCD_D15 0x10f0 -MX28_PAD_LCD_D16__LCD_D16 0x1100 -MX28_PAD_LCD_D17__LCD_D17 0x1110 -MX28_PAD_LCD_D18__LCD_D18 0x1120 -MX28_PAD_LCD_D19__LCD_D19 0x1130 -MX28_PAD_LCD_D20__LCD_D20 0x1140 -MX28_PAD_LCD_D21__LCD_D21 0x1150 -MX28_PAD_LCD_D22__LCD_D22 0x1160 -MX28_PAD_LCD_D23__LCD_D23 0x1170 -MX28_PAD_LCD_RD_E__LCD_RD_E 0x1180 -MX28_PAD_LCD_WR_RWN__LCD_WR_RWN 0x1190 -MX28_PAD_LCD_RS__LCD_RS 0x11a0 -MX28_PAD_LCD_CS__LCD_CS 0x11b0 -MX28_PAD_LCD_VSYNC__LCD_VSYNC 0x11c0 -MX28_PAD_LCD_HSYNC__LCD_HSYNC 0x11d0 -MX28_PAD_LCD_DOTCLK__LCD_DOTCLK 0x11e0 -MX28_PAD_LCD_ENABLE__LCD_ENABLE 0x11f0 -MX28_PAD_SSP0_DATA0__SSP0_D0 0x2000 -MX28_PAD_SSP0_DATA1__SSP0_D1 0x2010 -MX28_PAD_SSP0_DATA2__SSP0_D2 0x2020 -MX28_PAD_SSP0_DATA3__SSP0_D3 0x2030 -MX28_PAD_SSP0_DATA4__SSP0_D4 0x2040 -MX28_PAD_SSP0_DATA5__SSP0_D5 0x2050 -MX28_PAD_SSP0_DATA6__SSP0_D6 0x2060 -MX28_PAD_SSP0_DATA7__SSP0_D7 0x2070 -MX28_PAD_SSP0_CMD__SSP0_CMD 0x2080 -MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT 0x2090 -MX28_PAD_SSP0_SCK__SSP0_SCK 0x20a0 -MX28_PAD_SSP1_SCK__SSP1_SCK 0x20c0 -MX28_PAD_SSP1_CMD__SSP1_CMD 0x20d0 -MX28_PAD_SSP1_DATA0__SSP1_D0 0x20e0 -MX28_PAD_SSP1_DATA3__SSP1_D3 0x20f0 -MX28_PAD_SSP2_SCK__SSP2_SCK 0x2100 -MX28_PAD_SSP2_MOSI__SSP2_CMD 0x2110 -MX28_PAD_SSP2_MISO__SSP2_D0 0x2120 -MX28_PAD_SSP2_SS0__SSP2_D3 0x2130 -MX28_PAD_SSP2_SS1__SSP2_D4 0x2140 -MX28_PAD_SSP2_SS2__SSP2_D5 0x2150 -MX28_PAD_SSP3_SCK__SSP3_SCK 0x2180 -MX28_PAD_SSP3_MOSI__SSP3_CMD 0x2190 -MX28_PAD_SSP3_MISO__SSP3_D0 0x21a0 -MX28_PAD_SSP3_SS0__SSP3_D3 0x21b0 -MX28_PAD_AUART0_RX__AUART0_RX 0x3000 -MX28_PAD_AUART0_TX__AUART0_TX 0x3010 -MX28_PAD_AUART0_CTS__AUART0_CTS 0x3020 -MX28_PAD_AUART0_RTS__AUART0_RTS 0x3030 -MX28_PAD_AUART1_RX__AUART1_RX 0x3040 -MX28_PAD_AUART1_TX__AUART1_TX 0x3050 -MX28_PAD_AUART1_CTS__AUART1_CTS 0x3060 -MX28_PAD_AUART1_RTS__AUART1_RTS 0x3070 -MX28_PAD_AUART2_RX__AUART2_RX 0x3080 -MX28_PAD_AUART2_TX__AUART2_TX 0x3090 -MX28_PAD_AUART2_CTS__AUART2_CTS 0x30a0 -MX28_PAD_AUART2_RTS__AUART2_RTS 0x30b0 -MX28_PAD_AUART3_RX__AUART3_RX 0x30c0 -MX28_PAD_AUART3_TX__AUART3_TX 0x30d0 -MX28_PAD_AUART3_CTS__AUART3_CTS 0x30e0 -MX28_PAD_AUART3_RTS__AUART3_RTS 0x30f0 -MX28_PAD_PWM0__PWM_0 0x3100 -MX28_PAD_PWM1__PWM_1 0x3110 -MX28_PAD_PWM2__PWM_2 0x3120 -MX28_PAD_SAIF0_MCLK__SAIF0_MCLK 0x3140 -MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK 0x3150 -MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK 0x3160 -MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 0x3170 -MX28_PAD_I2C0_SCL__I2C0_SCL 0x3180 -MX28_PAD_I2C0_SDA__I2C0_SDA 0x3190 -MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 0x31a0 -MX28_PAD_SPDIF__SPDIF_TX 0x31b0 -MX28_PAD_PWM3__PWM_3 0x31c0 -MX28_PAD_PWM4__PWM_4 0x31d0 -MX28_PAD_LCD_RESET__LCD_RESET 0x31e0 -MX28_PAD_ENET0_MDC__ENET0_MDC 0x4000 -MX28_PAD_ENET0_MDIO__ENET0_MDIO 0x4010 -MX28_PAD_ENET0_RX_EN__ENET0_RX_EN 0x4020 -MX28_PAD_ENET0_RXD0__ENET0_RXD0 0x4030 -MX28_PAD_ENET0_RXD1__ENET0_RXD1 0x4040 -MX28_PAD_ENET0_TX_CLK__ENET0_TX_CLK 0x4050 -MX28_PAD_ENET0_TX_EN__ENET0_TX_EN 0x4060 -MX28_PAD_ENET0_TXD0__ENET0_TXD0 0x4070 -MX28_PAD_ENET0_TXD1__ENET0_TXD1 0x4080 -MX28_PAD_ENET0_RXD2__ENET0_RXD2 0x4090 -MX28_PAD_ENET0_RXD3__ENET0_RXD3 0x40a0 -MX28_PAD_ENET0_TXD2__ENET0_TXD2 0x40b0 -MX28_PAD_ENET0_TXD3__ENET0_TXD3 0x40c0 -MX28_PAD_ENET0_RX_CLK__ENET0_RX_CLK 0x40d0 -MX28_PAD_ENET0_COL__ENET0_COL 0x40e0 -MX28_PAD_ENET0_CRS__ENET0_CRS 0x40f0 -MX28_PAD_ENET_CLK__CLKCTRL_ENET 0x4100 -MX28_PAD_JTAG_RTCK__JTAG_RTCK 0x4140 -MX28_PAD_EMI_D00__EMI_DATA0 0x5000 -MX28_PAD_EMI_D01__EMI_DATA1 0x5010 -MX28_PAD_EMI_D02__EMI_DATA2 0x5020 -MX28_PAD_EMI_D03__EMI_DATA3 0x5030 -MX28_PAD_EMI_D04__EMI_DATA4 0x5040 -MX28_PAD_EMI_D05__EMI_DATA5 0x5050 -MX28_PAD_EMI_D06__EMI_DATA6 0x5060 -MX28_PAD_EMI_D07__EMI_DATA7 0x5070 -MX28_PAD_EMI_D08__EMI_DATA8 0x5080 -MX28_PAD_EMI_D09__EMI_DATA9 0x5090 -MX28_PAD_EMI_D10__EMI_DATA10 0x50a0 -MX28_PAD_EMI_D11__EMI_DATA11 0x50b0 -MX28_PAD_EMI_D12__EMI_DATA12 0x50c0 -MX28_PAD_EMI_D13__EMI_DATA13 0x50d0 -MX28_PAD_EMI_D14__EMI_DATA14 0x50e0 -MX28_PAD_EMI_D15__EMI_DATA15 0x50f0 -MX28_PAD_EMI_ODT0__EMI_ODT0 0x5100 -MX28_PAD_EMI_DQM0__EMI_DQM0 0x5110 -MX28_PAD_EMI_ODT1__EMI_ODT1 0x5120 -MX28_PAD_EMI_DQM1__EMI_DQM1 0x5130 -MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK 0x5140 -MX28_PAD_EMI_CLK__EMI_CLK 0x5150 -MX28_PAD_EMI_DQS0__EMI_DQS0 0x5160 -MX28_PAD_EMI_DQS1__EMI_DQS1 0x5170 -MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN 0x51a0 -MX28_PAD_EMI_A00__EMI_ADDR0 0x6000 -MX28_PAD_EMI_A01__EMI_ADDR1 0x6010 -MX28_PAD_EMI_A02__EMI_ADDR2 0x6020 -MX28_PAD_EMI_A03__EMI_ADDR3 0x6030 -MX28_PAD_EMI_A04__EMI_ADDR4 0x6040 -MX28_PAD_EMI_A05__EMI_ADDR5 0x6050 -MX28_PAD_EMI_A06__EMI_ADDR6 0x6060 -MX28_PAD_EMI_A07__EMI_ADDR7 0x6070 -MX28_PAD_EMI_A08__EMI_ADDR8 0x6080 -MX28_PAD_EMI_A09__EMI_ADDR9 0x6090 -MX28_PAD_EMI_A10__EMI_ADDR10 0x60a0 -MX28_PAD_EMI_A11__EMI_ADDR11 0x60b0 -MX28_PAD_EMI_A12__EMI_ADDR12 0x60c0 -MX28_PAD_EMI_A13__EMI_ADDR13 0x60d0 -MX28_PAD_EMI_A14__EMI_ADDR14 0x60e0 -MX28_PAD_EMI_BA0__EMI_BA0 0x6100 -MX28_PAD_EMI_BA1__EMI_BA1 0x6110 -MX28_PAD_EMI_BA2__EMI_BA2 0x6120 -MX28_PAD_EMI_CASN__EMI_CASN 0x6130 -MX28_PAD_EMI_RASN__EMI_RASN 0x6140 -MX28_PAD_EMI_WEN__EMI_WEN 0x6150 -MX28_PAD_EMI_CE0N__EMI_CE0N 0x6160 -MX28_PAD_EMI_CE1N__EMI_CE1N 0x6170 -MX28_PAD_EMI_CKE__EMI_CKE 0x6180 -MX28_PAD_GPMI_D00__SSP1_D0 0x0001 -MX28_PAD_GPMI_D01__SSP1_D1 0x0011 -MX28_PAD_GPMI_D02__SSP1_D2 0x0021 -MX28_PAD_GPMI_D03__SSP1_D3 0x0031 -MX28_PAD_GPMI_D04__SSP1_D4 0x0041 -MX28_PAD_GPMI_D05__SSP1_D5 0x0051 -MX28_PAD_GPMI_D06__SSP1_D6 0x0061 -MX28_PAD_GPMI_D07__SSP1_D7 0x0071 -MX28_PAD_GPMI_CE0N__SSP3_D0 0x0101 -MX28_PAD_GPMI_CE1N__SSP3_D3 0x0111 -MX28_PAD_GPMI_CE2N__CAN1_TX 0x0121 -MX28_PAD_GPMI_CE3N__CAN1_RX 0x0131 -MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT 0x0141 -MX28_PAD_GPMI_RDY1__SSP1_CMD 0x0151 -MX28_PAD_GPMI_RDY2__CAN0_TX 0x0161 -MX28_PAD_GPMI_RDY3__CAN0_RX 0x0171 -MX28_PAD_GPMI_RDN__SSP3_SCK 0x0181 -MX28_PAD_GPMI_WRN__SSP1_SCK 0x0191 -MX28_PAD_GPMI_ALE__SSP3_D1 0x01a1 -MX28_PAD_GPMI_CLE__SSP3_D2 0x01b1 -MX28_PAD_GPMI_RESETN__SSP3_CMD 0x01c1 -MX28_PAD_LCD_D03__ETM_DA8 0x1031 -MX28_PAD_LCD_D04__ETM_DA9 0x1041 -MX28_PAD_LCD_D08__ETM_DA3 0x1081 -MX28_PAD_LCD_D09__ETM_DA4 0x1091 -MX28_PAD_LCD_D20__ENET1_1588_EVENT2_OUT 0x1141 -MX28_PAD_LCD_D21__ENET1_1588_EVENT2_IN 0x1151 -MX28_PAD_LCD_D22__ENET1_1588_EVENT3_OUT 0x1161 -MX28_PAD_LCD_D23__ENET1_1588_EVENT3_IN 0x1171 -MX28_PAD_LCD_RD_E__LCD_VSYNC 0x1181 -MX28_PAD_LCD_WR_RWN__LCD_HSYNC 0x1191 -MX28_PAD_LCD_RS__LCD_DOTCLK 0x11a1 -MX28_PAD_LCD_CS__LCD_ENABLE 0x11b1 -MX28_PAD_LCD_VSYNC__SAIF1_SDATA0 0x11c1 -MX28_PAD_LCD_HSYNC__SAIF1_SDATA1 0x11d1 -MX28_PAD_LCD_DOTCLK__SAIF1_MCLK 0x11e1 -MX28_PAD_SSP0_DATA4__SSP2_D0 0x2041 -MX28_PAD_SSP0_DATA5__SSP2_D3 0x2051 -MX28_PAD_SSP0_DATA6__SSP2_CMD 0x2061 -MX28_PAD_SSP0_DATA7__SSP2_SCK 0x2071 -MX28_PAD_SSP1_SCK__SSP2_D1 0x20c1 -MX28_PAD_SSP1_CMD__SSP2_D2 0x20d1 -MX28_PAD_SSP1_DATA0__SSP2_D6 0x20e1 -MX28_PAD_SSP1_DATA3__SSP2_D7 0x20f1 -MX28_PAD_SSP2_SCK__AUART2_RX 0x2101 -MX28_PAD_SSP2_MOSI__AUART2_TX 0x2111 -MX28_PAD_SSP2_MISO__AUART3_RX 0x2121 -MX28_PAD_SSP2_SS0__AUART3_TX 0x2131 -MX28_PAD_SSP2_SS1__SSP2_D1 0x2141 -MX28_PAD_SSP2_SS2__SSP2_D2 0x2151 -MX28_PAD_SSP3_SCK__AUART4_TX 0x2181 -MX28_PAD_SSP3_MOSI__AUART4_RX 0x2191 -MX28_PAD_SSP3_MISO__AUART4_RTS 0x21a1 -MX28_PAD_SSP3_SS0__AUART4_CTS 0x21b1 -MX28_PAD_AUART0_RX__I2C0_SCL 0x3001 -MX28_PAD_AUART0_TX__I2C0_SDA 0x3011 -MX28_PAD_AUART0_CTS__AUART4_RX 0x3021 -MX28_PAD_AUART0_RTS__AUART4_TX 0x3031 -MX28_PAD_AUART1_RX__SSP2_CARD_DETECT 0x3041 -MX28_PAD_AUART1_TX__SSP3_CARD_DETECT 0x3051 -MX28_PAD_AUART1_CTS__USB0_OVERCURRENT 0x3061 -MX28_PAD_AUART1_RTS__USB0_ID 0x3071 -MX28_PAD_AUART2_RX__SSP3_D1 0x3081 -MX28_PAD_AUART2_TX__SSP3_D2 0x3091 -MX28_PAD_AUART2_CTS__I2C1_SCL 0x30a1 -MX28_PAD_AUART2_RTS__I2C1_SDA 0x30b1 -MX28_PAD_AUART3_RX__CAN0_TX 0x30c1 -MX28_PAD_AUART3_TX__CAN0_RX 0x30d1 -MX28_PAD_AUART3_CTS__CAN1_TX 0x30e1 -MX28_PAD_AUART3_RTS__CAN1_RX 0x30f1 -MX28_PAD_PWM0__I2C1_SCL 0x3101 -MX28_PAD_PWM1__I2C1_SDA 0x3111 -MX28_PAD_PWM2__USB0_ID 0x3121 -MX28_PAD_SAIF0_MCLK__PWM_3 0x3141 -MX28_PAD_SAIF0_LRCLK__PWM_4 0x3151 -MX28_PAD_SAIF0_BITCLK__PWM_5 0x3161 -MX28_PAD_SAIF0_SDATA0__PWM_6 0x3171 -MX28_PAD_I2C0_SCL__TIMROT_ROTARYA 0x3181 -MX28_PAD_I2C0_SDA__TIMROT_ROTARYB 0x3191 -MX28_PAD_SAIF1_SDATA0__PWM_7 0x31a1 -MX28_PAD_LCD_RESET__LCD_VSYNC 0x31e1 -MX28_PAD_ENET0_MDC__GPMI_CE4N 0x4001 -MX28_PAD_ENET0_MDIO__GPMI_CE5N 0x4011 -MX28_PAD_ENET0_RX_EN__GPMI_CE6N 0x4021 -MX28_PAD_ENET0_RXD0__GPMI_CE7N 0x4031 -MX28_PAD_ENET0_RXD1__GPMI_READY4 0x4041 -MX28_PAD_ENET0_TX_CLK__HSADC_TRIGGER 0x4051 -MX28_PAD_ENET0_TX_EN__GPMI_READY5 0x4061 -MX28_PAD_ENET0_TXD0__GPMI_READY6 0x4071 -MX28_PAD_ENET0_TXD1__GPMI_READY7 0x4081 -MX28_PAD_ENET0_RXD2__ENET1_RXD0 0x4091 -MX28_PAD_ENET0_RXD3__ENET1_RXD1 0x40a1 -MX28_PAD_ENET0_TXD2__ENET1_TXD0 0x40b1 -MX28_PAD_ENET0_TXD3__ENET1_TXD1 0x40c1 -MX28_PAD_ENET0_RX_CLK__ENET0_RX_ER 0x40d1 -MX28_PAD_ENET0_COL__ENET1_TX_EN 0x40e1 -MX28_PAD_ENET0_CRS__ENET1_RX_EN 0x40f1 -MX28_PAD_GPMI_CE2N__ENET0_RX_ER 0x0122 -MX28_PAD_GPMI_CE3N__SAIF1_MCLK 0x0132 -MX28_PAD_GPMI_RDY0__USB0_ID 0x0142 -MX28_PAD_GPMI_RDY2__ENET0_TX_ER 0x0162 -MX28_PAD_GPMI_RDY3__HSADC_TRIGGER 0x0172 -MX28_PAD_GPMI_ALE__SSP3_D4 0x01a2 -MX28_PAD_GPMI_CLE__SSP3_D5 0x01b2 -MX28_PAD_LCD_D00__ETM_DA0 0x1002 -MX28_PAD_LCD_D01__ETM_DA1 0x1012 -MX28_PAD_LCD_D02__ETM_DA2 0x1022 -MX28_PAD_LCD_D03__ETM_DA3 0x1032 -MX28_PAD_LCD_D04__ETM_DA4 0x1042 -MX28_PAD_LCD_D05__ETM_DA5 0x1052 -MX28_PAD_LCD_D06__ETM_DA6 0x1062 -MX28_PAD_LCD_D07__ETM_DA7 0x1072 -MX28_PAD_LCD_D08__ETM_DA8 0x1082 -MX28_PAD_LCD_D09__ETM_DA9 0x1092 -MX28_PAD_LCD_D10__ETM_DA10 0x10a2 -MX28_PAD_LCD_D11__ETM_DA11 0x10b2 -MX28_PAD_LCD_D12__ETM_DA12 0x10c2 -MX28_PAD_LCD_D13__ETM_DA13 0x10d2 -MX28_PAD_LCD_D14__ETM_DA14 0x10e2 -MX28_PAD_LCD_D15__ETM_DA15 0x10f2 -MX28_PAD_LCD_D16__ETM_DA7 0x1102 -MX28_PAD_LCD_D17__ETM_DA6 0x1112 -MX28_PAD_LCD_D18__ETM_DA5 0x1122 -MX28_PAD_LCD_D19__ETM_DA4 0x1132 -MX28_PAD_LCD_D20__ETM_DA3 0x1142 -MX28_PAD_LCD_D21__ETM_DA2 0x1152 -MX28_PAD_LCD_D22__ETM_DA1 0x1162 -MX28_PAD_LCD_D23__ETM_DA0 0x1172 -MX28_PAD_LCD_RD_E__ETM_TCTL 0x1182 -MX28_PAD_LCD_WR_RWN__ETM_TCLK 0x1192 -MX28_PAD_LCD_HSYNC__ETM_TCTL 0x11d2 -MX28_PAD_LCD_DOTCLK__ETM_TCLK 0x11e2 -MX28_PAD_SSP1_SCK__ENET0_1588_EVENT2_OUT 0x20c2 -MX28_PAD_SSP1_CMD__ENET0_1588_EVENT2_IN 0x20d2 -MX28_PAD_SSP1_DATA0__ENET0_1588_EVENT3_OUT 0x20e2 -MX28_PAD_SSP1_DATA3__ENET0_1588_EVENT3_IN 0x20f2 -MX28_PAD_SSP2_SCK__SAIF0_SDATA1 0x2102 -MX28_PAD_SSP2_MOSI__SAIF0_SDATA2 0x2112 -MX28_PAD_SSP2_MISO__SAIF1_SDATA1 0x2122 -MX28_PAD_SSP2_SS0__SAIF1_SDATA2 0x2132 -MX28_PAD_SSP2_SS1__USB1_OVERCURRENT 0x2142 -MX28_PAD_SSP2_SS2__USB0_OVERCURRENT 0x2152 -MX28_PAD_SSP3_SCK__ENET1_1588_EVENT0_OUT 0x2182 -MX28_PAD_SSP3_MOSI__ENET1_1588_EVENT0_IN 0x2192 -MX28_PAD_SSP3_MISO__ENET1_1588_EVENT1_OUT 0x21a2 -MX28_PAD_SSP3_SS0__ENET1_1588_EVENT1_IN 0x21b2 -MX28_PAD_AUART0_RX__DUART_CTS 0x3002 -MX28_PAD_AUART0_TX__DUART_RTS 0x3012 -MX28_PAD_AUART0_CTS__DUART_RX 0x3022 -MX28_PAD_AUART0_RTS__DUART_TX 0x3032 -MX28_PAD_AUART1_RX__PWM_0 0x3042 -MX28_PAD_AUART1_TX__PWM_1 0x3052 -MX28_PAD_AUART1_CTS__TIMROT_ROTARYA 0x3062 -MX28_PAD_AUART1_RTS__TIMROT_ROTARYB 0x3072 -MX28_PAD_AUART2_RX__SSP3_D4 0x3082 -MX28_PAD_AUART2_TX__SSP3_D5 0x3092 -MX28_PAD_AUART2_CTS__SAIF1_BITCLK 0x30a2 -MX28_PAD_AUART2_RTS__SAIF1_LRCLK 0x30b2 -MX28_PAD_AUART3_RX__ENET0_1588_EVENT0_OUT 0x30c2 -MX28_PAD_AUART3_TX__ENET0_1588_EVENT0_IN 0x30d2 -MX28_PAD_AUART3_CTS__ENET0_1588_EVENT1_OUT 0x30e2 -MX28_PAD_AUART3_RTS__ENET0_1588_EVENT1_IN 0x30f2 -MX28_PAD_PWM0__DUART_RX 0x3102 -MX28_PAD_PWM1__DUART_TX 0x3112 -MX28_PAD_PWM2__USB1_OVERCURRENT 0x3122 -MX28_PAD_SAIF0_MCLK__AUART4_CTS 0x3142 -MX28_PAD_SAIF0_LRCLK__AUART4_RTS 0x3152 -MX28_PAD_SAIF0_BITCLK__AUART4_RX 0x3162 -MX28_PAD_SAIF0_SDATA0__AUART4_TX 0x3172 -MX28_PAD_I2C0_SCL__DUART_RX 0x3182 -MX28_PAD_I2C0_SDA__DUART_TX 0x3192 -MX28_PAD_SAIF1_SDATA0__SAIF0_SDATA1 0x31a2 -MX28_PAD_SPDIF__ENET1_RX_ER 0x31b2 -MX28_PAD_ENET0_MDC__SAIF0_SDATA1 0x4002 -MX28_PAD_ENET0_MDIO__SAIF0_SDATA2 0x4012 -MX28_PAD_ENET0_RX_EN__SAIF1_SDATA1 0x4022 -MX28_PAD_ENET0_RXD0__SAIF1_SDATA2 0x4032 -MX28_PAD_ENET0_TX_CLK__ENET0_1588_EVENT2_OUT 0x4052 -MX28_PAD_ENET0_RXD2__ENET0_1588_EVENT0_OUT 0x4092 -MX28_PAD_ENET0_RXD3__ENET0_1588_EVENT0_IN 0x40a2 -MX28_PAD_ENET0_TXD2__ENET0_1588_EVENT1_OUT 0x40b2 -MX28_PAD_ENET0_TXD3__ENET0_1588_EVENT1_IN 0x40c2 -MX28_PAD_ENET0_RX_CLK__ENET0_1588_EVENT2_IN 0x40d2 -MX28_PAD_ENET0_COL__ENET0_1588_EVENT3_OUT 0x40e2 -MX28_PAD_ENET0_CRS__ENET0_1588_EVENT3_IN 0x40f2 -MX28_PAD_GPMI_D00__GPIO_0_0 0x0003 -MX28_PAD_GPMI_D01__GPIO_0_1 0x0013 -MX28_PAD_GPMI_D02__GPIO_0_2 0x0023 -MX28_PAD_GPMI_D03__GPIO_0_3 0x0033 -MX28_PAD_GPMI_D04__GPIO_0_4 0x0043 -MX28_PAD_GPMI_D05__GPIO_0_5 0x0053 -MX28_PAD_GPMI_D06__GPIO_0_6 0x0063 -MX28_PAD_GPMI_D07__GPIO_0_7 0x0073 -MX28_PAD_GPMI_CE0N__GPIO_0_16 0x0103 -MX28_PAD_GPMI_CE1N__GPIO_0_17 0x0113 -MX28_PAD_GPMI_CE2N__GPIO_0_18 0x0123 -MX28_PAD_GPMI_CE3N__GPIO_0_19 0x0133 -MX28_PAD_GPMI_RDY0__GPIO_0_20 0x0143 -MX28_PAD_GPMI_RDY1__GPIO_0_21 0x0153 -MX28_PAD_GPMI_RDY2__GPIO_0_22 0x0163 -MX28_PAD_GPMI_RDY3__GPIO_0_23 0x0173 -MX28_PAD_GPMI_RDN__GPIO_0_24 0x0183 -MX28_PAD_GPMI_WRN__GPIO_0_25 0x0193 -MX28_PAD_GPMI_ALE__GPIO_0_26 0x01a3 -MX28_PAD_GPMI_CLE__GPIO_0_27 0x01b3 -MX28_PAD_GPMI_RESETN__GPIO_0_28 0x01c3 -MX28_PAD_LCD_D00__GPIO_1_0 0x1003 -MX28_PAD_LCD_D01__GPIO_1_1 0x1013 -MX28_PAD_LCD_D02__GPIO_1_2 0x1023 -MX28_PAD_LCD_D03__GPIO_1_3 0x1033 -MX28_PAD_LCD_D04__GPIO_1_4 0x1043 -MX28_PAD_LCD_D05__GPIO_1_5 0x1053 -MX28_PAD_LCD_D06__GPIO_1_6 0x1063 -MX28_PAD_LCD_D07__GPIO_1_7 0x1073 -MX28_PAD_LCD_D08__GPIO_1_8 0x1083 -MX28_PAD_LCD_D09__GPIO_1_9 0x1093 -MX28_PAD_LCD_D10__GPIO_1_10 0x10a3 -MX28_PAD_LCD_D11__GPIO_1_11 0x10b3 -MX28_PAD_LCD_D12__GPIO_1_12 0x10c3 -MX28_PAD_LCD_D13__GPIO_1_13 0x10d3 -MX28_PAD_LCD_D14__GPIO_1_14 0x10e3 -MX28_PAD_LCD_D15__GPIO_1_15 0x10f3 -MX28_PAD_LCD_D16__GPIO_1_16 0x1103 -MX28_PAD_LCD_D17__GPIO_1_17 0x1113 -MX28_PAD_LCD_D18__GPIO_1_18 0x1123 -MX28_PAD_LCD_D19__GPIO_1_19 0x1133 -MX28_PAD_LCD_D20__GPIO_1_20 0x1143 -MX28_PAD_LCD_D21__GPIO_1_21 0x1153 -MX28_PAD_LCD_D22__GPIO_1_22 0x1163 -MX28_PAD_LCD_D23__GPIO_1_23 0x1173 -MX28_PAD_LCD_RD_E__GPIO_1_24 0x1183 -MX28_PAD_LCD_WR_RWN__GPIO_1_25 0x1193 -MX28_PAD_LCD_RS__GPIO_1_26 0x11a3 -MX28_PAD_LCD_CS__GPIO_1_27 0x11b3 -MX28_PAD_LCD_VSYNC__GPIO_1_28 0x11c3 -MX28_PAD_LCD_HSYNC__GPIO_1_29 0x11d3 -MX28_PAD_LCD_DOTCLK__GPIO_1_30 0x11e3 -MX28_PAD_LCD_ENABLE__GPIO_1_31 0x11f3 -MX28_PAD_SSP0_DATA0__GPIO_2_0 0x2003 -MX28_PAD_SSP0_DATA1__GPIO_2_1 0x2013 -MX28_PAD_SSP0_DATA2__GPIO_2_2 0x2023 -MX28_PAD_SSP0_DATA3__GPIO_2_3 0x2033 -MX28_PAD_SSP0_DATA4__GPIO_2_4 0x2043 -MX28_PAD_SSP0_DATA5__GPIO_2_5 0x2053 -MX28_PAD_SSP0_DATA6__GPIO_2_6 0x2063 -MX28_PAD_SSP0_DATA7__GPIO_2_7 0x2073 -MX28_PAD_SSP0_CMD__GPIO_2_8 0x2083 -MX28_PAD_SSP0_DETECT__GPIO_2_9 0x2093 -MX28_PAD_SSP0_SCK__GPIO_2_10 0x20a3 -MX28_PAD_SSP1_SCK__GPIO_2_12 0x20c3 -MX28_PAD_SSP1_CMD__GPIO_2_13 0x20d3 -MX28_PAD_SSP1_DATA0__GPIO_2_14 0x20e3 -MX28_PAD_SSP1_DATA3__GPIO_2_15 0x20f3 -MX28_PAD_SSP2_SCK__GPIO_2_16 0x2103 -MX28_PAD_SSP2_MOSI__GPIO_2_17 0x2113 -MX28_PAD_SSP2_MISO__GPIO_2_18 0x2123 -MX28_PAD_SSP2_SS0__GPIO_2_19 0x2133 -MX28_PAD_SSP2_SS1__GPIO_2_20 0x2143 -MX28_PAD_SSP2_SS2__GPIO_2_21 0x2153 -MX28_PAD_SSP3_SCK__GPIO_2_24 0x2183 -MX28_PAD_SSP3_MOSI__GPIO_2_25 0x2193 -MX28_PAD_SSP3_MISO__GPIO_2_26 0x21a3 -MX28_PAD_SSP3_SS0__GPIO_2_27 0x21b3 -MX28_PAD_AUART0_RX__GPIO_3_0 0x3003 -MX28_PAD_AUART0_TX__GPIO_3_1 0x3013 -MX28_PAD_AUART0_CTS__GPIO_3_2 0x3023 -MX28_PAD_AUART0_RTS__GPIO_3_3 0x3033 -MX28_PAD_AUART1_RX__GPIO_3_4 0x3043 -MX28_PAD_AUART1_TX__GPIO_3_5 0x3053 -MX28_PAD_AUART1_CTS__GPIO_3_6 0x3063 -MX28_PAD_AUART1_RTS__GPIO_3_7 0x3073 -MX28_PAD_AUART2_RX__GPIO_3_8 0x3083 -MX28_PAD_AUART2_TX__GPIO_3_9 0x3093 -MX28_PAD_AUART2_CTS__GPIO_3_10 0x30a3 -MX28_PAD_AUART2_RTS__GPIO_3_11 0x30b3 -MX28_PAD_AUART3_RX__GPIO_3_12 0x30c3 -MX28_PAD_AUART3_TX__GPIO_3_13 0x30d3 -MX28_PAD_AUART3_CTS__GPIO_3_14 0x30e3 -MX28_PAD_AUART3_RTS__GPIO_3_15 0x30f3 -MX28_PAD_PWM0__GPIO_3_16 0x3103 -MX28_PAD_PWM1__GPIO_3_17 0x3113 -MX28_PAD_PWM2__GPIO_3_18 0x3123 -MX28_PAD_SAIF0_MCLK__GPIO_3_20 0x3143 -MX28_PAD_SAIF0_LRCLK__GPIO_3_21 0x3153 -MX28_PAD_SAIF0_BITCLK__GPIO_3_22 0x3163 -MX28_PAD_SAIF0_SDATA0__GPIO_3_23 0x3173 -MX28_PAD_I2C0_SCL__GPIO_3_24 0x3183 -MX28_PAD_I2C0_SDA__GPIO_3_25 0x3193 -MX28_PAD_SAIF1_SDATA0__GPIO_3_26 0x31a3 -MX28_PAD_SPDIF__GPIO_3_27 0x31b3 -MX28_PAD_PWM3__GPIO_3_28 0x31c3 -MX28_PAD_PWM4__GPIO_3_29 0x31d3 -MX28_PAD_LCD_RESET__GPIO_3_30 0x31e3 -MX28_PAD_ENET0_MDC__GPIO_4_0 0x4003 -MX28_PAD_ENET0_MDIO__GPIO_4_1 0x4013 -MX28_PAD_ENET0_RX_EN__GPIO_4_2 0x4023 -MX28_PAD_ENET0_RXD0__GPIO_4_3 0x4033 -MX28_PAD_ENET0_RXD1__GPIO_4_4 0x4043 -MX28_PAD_ENET0_TX_CLK__GPIO_4_5 0x4053 -MX28_PAD_ENET0_TX_EN__GPIO_4_6 0x4063 -MX28_PAD_ENET0_TXD0__GPIO_4_7 0x4073 -MX28_PAD_ENET0_TXD1__GPIO_4_8 0x4083 -MX28_PAD_ENET0_RXD2__GPIO_4_9 0x4093 -MX28_PAD_ENET0_RXD3__GPIO_4_10 0x40a3 -MX28_PAD_ENET0_TXD2__GPIO_4_11 0x40b3 -MX28_PAD_ENET0_TXD3__GPIO_4_12 0x40c3 -MX28_PAD_ENET0_RX_CLK__GPIO_4_13 0x40d3 -MX28_PAD_ENET0_COL__GPIO_4_14 0x40e3 -MX28_PAD_ENET0_CRS__GPIO_4_15 0x40f3 -MX28_PAD_ENET_CLK__GPIO_4_16 0x4103 -MX28_PAD_JTAG_RTCK__GPIO_4_20 0x4143 - -Valid values for i.MX23 pinmux-id: - -pinmux id ------- -- -MX23_PAD_GPMI_D00__GPMI_D00 0x0000 -MX23_PAD_GPMI_D01__GPMI_D01 0x0010 -MX23_PAD_GPMI_D02__GPMI_D02 0x0020 -MX23_PAD_GPMI_D03__GPMI_D03 0x0030 -MX23_PAD_GPMI_D04__GPMI_D04 0x0040 -MX23_PAD_GPMI_D05__GPMI_D05 0x0050 -MX23_PAD_GPMI_D06__GPMI_D06 0x0060 -MX23_PAD_GPMI_D07__GPMI_D07 0x0070 -MX23_PAD_GPMI_D08__GPMI_D08 0x0080 -MX23_PAD_GPMI_D09__GPMI_D09 0x0090 -MX23_PAD_GPMI_D10__GPMI_D10 0x00a0 -MX23_PAD_GPMI_D11__GPMI_D11 0x00b0 -MX23_PAD_GPMI_D12__GPMI_D12 0x00c0 -MX23_PAD_GPMI_D13__GPMI_D13 0x00d0 -MX23_PAD_GPMI_D14__GPMI_D14 0x00e0 -MX23_PAD_GPMI_D15__GPMI_D15 0x00f0 -MX23_PAD_GPMI_CLE__GPMI_CLE 0x0100 -MX23_PAD_GPMI_ALE__GPMI_ALE 0x0110 -MX23_PAD_GPMI_CE2N__GPMI_CE2N 0x0120 -MX23_PAD_GPMI_RDY0__GPMI_RDY0 0x0130 -MX23_PAD_GPMI_RDY1__GPMI_RDY1 0x0140 -MX23_PAD_GPMI_RDY2__GPMI_RDY2 0x0150 -MX23_PAD_GPMI_RDY3__GPMI_RDY3 0x0160 -MX23_PAD_GPMI_WPN__GPMI_WPN 0x0170 -MX23_PAD_GPMI_WRN__GPMI_WRN 0x0180 -MX23_PAD_GPMI_RDN__GPMI_RDN 0x0190 -MX23_PAD_AUART1_CTS__AUART1_CTS 0x01a0 -MX23_PAD_AUART1_RTS__AUART1_RTS 0x01b0 -MX23_PAD_AUART1_RX__AUART1_RX 0x01c0 -MX23_PAD_AUART1_TX__AUART1_TX 0x01d0 -MX23_PAD_I2C_SCL__I2C_SCL 0x01e0 -MX23_PAD_I2C_SDA__I2C_SDA 0x01f0 -MX23_PAD_LCD_D00__LCD_D00 0x1000 -MX23_PAD_LCD_D01__LCD_D01 0x1010 -MX23_PAD_LCD_D02__LCD_D02 0x1020 -MX23_PAD_LCD_D03__LCD_D03 0x1030 -MX23_PAD_LCD_D04__LCD_D04 0x1040 -MX23_PAD_LCD_D05__LCD_D05 0x1050 -MX23_PAD_LCD_D06__LCD_D06 0x1060 -MX23_PAD_LCD_D07__LCD_D07 0x1070 -MX23_PAD_LCD_D08__LCD_D08 0x1080 -MX23_PAD_LCD_D09__LCD_D09 0x1090 -MX23_PAD_LCD_D10__LCD_D10 0x10a0 -MX23_PAD_LCD_D11__LCD_D11 0x10b0 -MX23_PAD_LCD_D12__LCD_D12 0x10c0 -MX23_PAD_LCD_D13__LCD_D13 0x10d0 -MX23_PAD_LCD_D14__LCD_D14 0x10e0 -MX23_PAD_LCD_D15__LCD_D15 0x10f0 -MX23_PAD_LCD_D16__LCD_D16 0x1100 -MX23_PAD_LCD_D17__LCD_D17 0x1110 -MX23_PAD_LCD_RESET__LCD_RESET 0x1120 -MX23_PAD_LCD_RS__LCD_RS 0x1130 -MX23_PAD_LCD_WR__LCD_WR 0x1140 -MX23_PAD_LCD_CS__LCD_CS 0x1150 -MX23_PAD_LCD_DOTCK__LCD_DOTCK 0x1160 -MX23_PAD_LCD_ENABLE__LCD_ENABLE 0x1170 -MX23_PAD_LCD_HSYNC__LCD_HSYNC 0x1180 -MX23_PAD_LCD_VSYNC__LCD_VSYNC 0x1190 -MX23_PAD_PWM0__PWM0 0x11a0 -MX23_PAD_PWM1__PWM1 0x11b0 -MX23_PAD_PWM2__PWM2 0x11c0 -MX23_PAD_PWM3__PWM3 0x11d0 -MX23_PAD_PWM4__PWM4 0x11e0 -MX23_PAD_SSP1_CMD__SSP1_CMD 0x2000 -MX23_PAD_SSP1_DETECT__SSP1_DETECT 0x2010 -MX23_PAD_SSP1_DATA0__SSP1_DATA0 0x2020 -MX23_PAD_SSP1_DATA1__SSP1_DATA1 0x2030 -MX23_PAD_SSP1_DATA2__SSP1_DATA2 0x2040 -MX23_PAD_SSP1_DATA3__SSP1_DATA3 0x2050 -MX23_PAD_SSP1_SCK__SSP1_SCK 0x2060 -MX23_PAD_ROTARYA__ROTARYA 0x2070 -MX23_PAD_ROTARYB__ROTARYB 0x2080 -MX23_PAD_EMI_A00__EMI_A00 0x2090 -MX23_PAD_EMI_A01__EMI_A01 0x20a0 -MX23_PAD_EMI_A02__EMI_A02 0x20b0 -MX23_PAD_EMI_A03__EMI_A03 0x20c0 -MX23_PAD_EMI_A04__EMI_A04 0x20d0 -MX23_PAD_EMI_A05__EMI_A05 0x20e0 -MX23_PAD_EMI_A06__EMI_A06 0x20f0 -MX23_PAD_EMI_A07__EMI_A07 0x2100 -MX23_PAD_EMI_A08__EMI_A08 0x2110 -MX23_PAD_EMI_A09__EMI_A09 0x2120 -MX23_PAD_EMI_A10__EMI_A10 0x2130 -MX23_PAD_EMI_A11__EMI_A11 0x2140 -MX23_PAD_EMI_A12__EMI_A12 0x2150 -MX23_PAD_EMI_BA0__EMI_BA0 0x2160 -MX23_PAD_EMI_BA1__EMI_BA1 0x2170 -MX23_PAD_EMI_CASN__EMI_CASN 0x2180 -MX23_PAD_EMI_CE0N__EMI_CE0N 0x2190 -MX23_PAD_EMI_CE1N__EMI_CE1N 0x21a0 -MX23_PAD_GPMI_CE1N__GPMI_CE1N 0x21b0 -MX23_PAD_GPMI_CE0N__GPMI_CE0N 0x21c0 -MX23_PAD_EMI_CKE__EMI_CKE 0x21d0 -MX23_PAD_EMI_RASN__EMI_RASN 0x21e0 -MX23_PAD_EMI_WEN__EMI_WEN 0x21f0 -MX23_PAD_EMI_D00__EMI_D00 0x3000 -MX23_PAD_EMI_D01__EMI_D01 0x3010 -MX23_PAD_EMI_D02__EMI_D02 0x3020 -MX23_PAD_EMI_D03__EMI_D03 0x3030 -MX23_PAD_EMI_D04__EMI_D04 0x3040 -MX23_PAD_EMI_D05__EMI_D05 0x3050 -MX23_PAD_EMI_D06__EMI_D06 0x3060 -MX23_PAD_EMI_D07__EMI_D07 0x3070 -MX23_PAD_EMI_D08__EMI_D08 0x3080 -MX23_PAD_EMI_D09__EMI_D09 0x3090 -MX23_PAD_EMI_D10__EMI_D10 0x30a0 -MX23_PAD_EMI_D11__EMI_D11 0x30b0 -MX23_PAD_EMI_D12__EMI_D12 0x30c0 -MX23_PAD_EMI_D13__EMI_D13 0x30d0 -MX23_PAD_EMI_D14__EMI_D14 0x30e0 -MX23_PAD_EMI_D15__EMI_D15 0x30f0 -MX23_PAD_EMI_DQM0__EMI_DQM0 0x3100 -MX23_PAD_EMI_DQM1__EMI_DQM1 0x3110 -MX23_PAD_EMI_DQS0__EMI_DQS0 0x3120 -MX23_PAD_EMI_DQS1__EMI_DQS1 0x3130 -MX23_PAD_EMI_CLK__EMI_CLK 0x3140 -MX23_PAD_EMI_CLKN__EMI_CLKN 0x3150 -MX23_PAD_GPMI_D00__LCD_D8 0x0001 -MX23_PAD_GPMI_D01__LCD_D9 0x0011 -MX23_PAD_GPMI_D02__LCD_D10 0x0021 -MX23_PAD_GPMI_D03__LCD_D11 0x0031 -MX23_PAD_GPMI_D04__LCD_D12 0x0041 -MX23_PAD_GPMI_D05__LCD_D13 0x0051 -MX23_PAD_GPMI_D06__LCD_D14 0x0061 -MX23_PAD_GPMI_D07__LCD_D15 0x0071 -MX23_PAD_GPMI_D08__LCD_D18 0x0081 -MX23_PAD_GPMI_D09__LCD_D19 0x0091 -MX23_PAD_GPMI_D10__LCD_D20 0x00a1 -MX23_PAD_GPMI_D11__LCD_D21 0x00b1 -MX23_PAD_GPMI_D12__LCD_D22 0x00c1 -MX23_PAD_GPMI_D13__LCD_D23 0x00d1 -MX23_PAD_GPMI_D14__AUART2_RX 0x00e1 -MX23_PAD_GPMI_D15__AUART2_TX 0x00f1 -MX23_PAD_GPMI_CLE__LCD_D16 0x0101 -MX23_PAD_GPMI_ALE__LCD_D17 0x0111 -MX23_PAD_GPMI_CE2N__ATA_A2 0x0121 -MX23_PAD_AUART1_RTS__IR_CLK 0x01b1 -MX23_PAD_AUART1_RX__IR_RX 0x01c1 -MX23_PAD_AUART1_TX__IR_TX 0x01d1 -MX23_PAD_I2C_SCL__GPMI_RDY2 0x01e1 -MX23_PAD_I2C_SDA__GPMI_CE2N 0x01f1 -MX23_PAD_LCD_D00__ETM_DA8 0x1001 -MX23_PAD_LCD_D01__ETM_DA9 0x1011 -MX23_PAD_LCD_D02__ETM_DA10 0x1021 -MX23_PAD_LCD_D03__ETM_DA11 0x1031 -MX23_PAD_LCD_D04__ETM_DA12 0x1041 -MX23_PAD_LCD_D05__ETM_DA13 0x1051 -MX23_PAD_LCD_D06__ETM_DA14 0x1061 -MX23_PAD_LCD_D07__ETM_DA15 0x1071 -MX23_PAD_LCD_D08__ETM_DA0 0x1081 -MX23_PAD_LCD_D09__ETM_DA1 0x1091 -MX23_PAD_LCD_D10__ETM_DA2 0x10a1 -MX23_PAD_LCD_D11__ETM_DA3 0x10b1 -MX23_PAD_LCD_D12__ETM_DA4 0x10c1 -MX23_PAD_LCD_D13__ETM_DA5 0x10d1 -MX23_PAD_LCD_D14__ETM_DA6 0x10e1 -MX23_PAD_LCD_D15__ETM_DA7 0x10f1 -MX23_PAD_LCD_RESET__ETM_TCTL 0x1121 -MX23_PAD_LCD_RS__ETM_TCLK 0x1131 -MX23_PAD_LCD_DOTCK__GPMI_RDY3 0x1161 -MX23_PAD_LCD_ENABLE__I2C_SCL 0x1171 -MX23_PAD_LCD_HSYNC__I2C_SDA 0x1181 -MX23_PAD_LCD_VSYNC__LCD_BUSY 0x1191 -MX23_PAD_PWM0__ROTARYA 0x11a1 -MX23_PAD_PWM1__ROTARYB 0x11b1 -MX23_PAD_PWM2__GPMI_RDY3 0x11c1 -MX23_PAD_PWM3__ETM_TCTL 0x11d1 -MX23_PAD_PWM4__ETM_TCLK 0x11e1 -MX23_PAD_SSP1_DETECT__GPMI_CE3N 0x2011 -MX23_PAD_SSP1_DATA1__I2C_SCL 0x2031 -MX23_PAD_SSP1_DATA2__I2C_SDA 0x2041 -MX23_PAD_ROTARYA__AUART2_RTS 0x2071 -MX23_PAD_ROTARYB__AUART2_CTS 0x2081 -MX23_PAD_GPMI_D00__SSP2_DATA0 0x0002 -MX23_PAD_GPMI_D01__SSP2_DATA1 0x0012 -MX23_PAD_GPMI_D02__SSP2_DATA2 0x0022 -MX23_PAD_GPMI_D03__SSP2_DATA3 0x0032 -MX23_PAD_GPMI_D04__SSP2_DATA4 0x0042 -MX23_PAD_GPMI_D05__SSP2_DATA5 0x0052 -MX23_PAD_GPMI_D06__SSP2_DATA6 0x0062 -MX23_PAD_GPMI_D07__SSP2_DATA7 0x0072 -MX23_PAD_GPMI_D08__SSP1_DATA4 0x0082 -MX23_PAD_GPMI_D09__SSP1_DATA5 0x0092 -MX23_PAD_GPMI_D10__SSP1_DATA6 0x00a2 -MX23_PAD_GPMI_D11__SSP1_DATA7 0x00b2 -MX23_PAD_GPMI_D15__GPMI_CE3N 0x00f2 -MX23_PAD_GPMI_RDY0__SSP2_DETECT 0x0132 -MX23_PAD_GPMI_RDY1__SSP2_CMD 0x0142 -MX23_PAD_GPMI_WRN__SSP2_SCK 0x0182 -MX23_PAD_AUART1_CTS__SSP1_DATA4 0x01a2 -MX23_PAD_AUART1_RTS__SSP1_DATA5 0x01b2 -MX23_PAD_AUART1_RX__SSP1_DATA6 0x01c2 -MX23_PAD_AUART1_TX__SSP1_DATA7 0x01d2 -MX23_PAD_I2C_SCL__AUART1_TX 0x01e2 -MX23_PAD_I2C_SDA__AUART1_RX 0x01f2 -MX23_PAD_LCD_D08__SAIF2_SDATA0 0x1082 -MX23_PAD_LCD_D09__SAIF1_SDATA0 0x1092 -MX23_PAD_LCD_D10__SAIF_MCLK_BITCLK 0x10a2 -MX23_PAD_LCD_D11__SAIF_LRCLK 0x10b2 -MX23_PAD_LCD_D12__SAIF2_SDATA1 0x10c2 -MX23_PAD_LCD_D13__SAIF2_SDATA2 0x10d2 -MX23_PAD_LCD_D14__SAIF1_SDATA2 0x10e2 -MX23_PAD_LCD_D15__SAIF1_SDATA1 0x10f2 -MX23_PAD_LCD_D16__SAIF_ALT_BITCLK 0x1102 -MX23_PAD_LCD_RESET__GPMI_CE3N 0x1122 -MX23_PAD_PWM0__DUART_RX 0x11a2 -MX23_PAD_PWM1__DUART_TX 0x11b2 -MX23_PAD_PWM3__AUART1_CTS 0x11d2 -MX23_PAD_PWM4__AUART1_RTS 0x11e2 -MX23_PAD_SSP1_CMD__JTAG_TDO 0x2002 -MX23_PAD_SSP1_DETECT__USB_OTG_ID 0x2012 -MX23_PAD_SSP1_DATA0__JTAG_TDI 0x2022 -MX23_PAD_SSP1_DATA1__JTAG_TCLK 0x2032 -MX23_PAD_SSP1_DATA2__JTAG_RTCK 0x2042 -MX23_PAD_SSP1_DATA3__JTAG_TMS 0x2052 -MX23_PAD_SSP1_SCK__JTAG_TRST 0x2062 -MX23_PAD_ROTARYA__SPDIF 0x2072 -MX23_PAD_ROTARYB__GPMI_CE3N 0x2082 -MX23_PAD_GPMI_D00__GPIO_0_0 0x0003 -MX23_PAD_GPMI_D01__GPIO_0_1 0x0013 -MX23_PAD_GPMI_D02__GPIO_0_2 0x0023 -MX23_PAD_GPMI_D03__GPIO_0_3 0x0033 -MX23_PAD_GPMI_D04__GPIO_0_4 0x0043 -MX23_PAD_GPMI_D05__GPIO_0_5 0x0053 -MX23_PAD_GPMI_D06__GPIO_0_6 0x0063 -MX23_PAD_GPMI_D07__GPIO_0_7 0x0073 -MX23_PAD_GPMI_D08__GPIO_0_8 0x0083 -MX23_PAD_GPMI_D09__GPIO_0_9 0x0093 -MX23_PAD_GPMI_D10__GPIO_0_10 0x00a3 -MX23_PAD_GPMI_D11__GPIO_0_11 0x00b3 -MX23_PAD_GPMI_D12__GPIO_0_12 0x00c3 -MX23_PAD_GPMI_D13__GPIO_0_13 0x00d3 -MX23_PAD_GPMI_D14__GPIO_0_14 0x00e3 -MX23_PAD_GPMI_D15__GPIO_0_15 0x00f3 -MX23_PAD_GPMI_CLE__GPIO_0_16 0x0103 -MX23_PAD_GPMI_ALE__GPIO_0_17 0x0113 -MX23_PAD_GPMI_CE2N__GPIO_0_18 0x0123 -MX23_PAD_GPMI_RDY0__GPIO_0_19 0x0133 -MX23_PAD_GPMI_RDY1__GPIO_0_20 0x0143 -MX23_PAD_GPMI_RDY2__GPIO_0_21 0x0153 -MX23_PAD_GPMI_RDY3__GPIO_0_22 0x0163 -MX23_PAD_GPMI_WPN__GPIO_0_23 0x0173 -MX23_PAD_GPMI_WRN__GPIO_0_24 0x0183 -MX23_PAD_GPMI_RDN__GPIO_0_25 0x0193 -MX23_PAD_AUART1_CTS__GPIO_0_26 0x01a3 -MX23_PAD_AUART1_RTS__GPIO_0_27 0x01b3 -MX23_PAD_AUART1_RX__GPIO_0_28 0x01c3 -MX23_PAD_AUART1_TX__GPIO_0_29 0x01d3 -MX23_PAD_I2C_SCL__GPIO_0_30 0x01e3 -MX23_PAD_I2C_SDA__GPIO_0_31 0x01f3 -MX23_PAD_LCD_D00__GPIO_1_0 0x1003 -MX23_PAD_LCD_D01__GPIO_1_1 0x1013 -MX23_PAD_LCD_D02__GPIO_1_2 0x1023 -MX23_PAD_LCD_D03__GPIO_1_3 0x1033 -MX23_PAD_LCD_D04__GPIO_1_4 0x1043 -MX23_PAD_LCD_D05__GPIO_1_5 0x1053 -MX23_PAD_LCD_D06__GPIO_1_6 0x1063 -MX23_PAD_LCD_D07__GPIO_1_7 0x1073 -MX23_PAD_LCD_D08__GPIO_1_8 0x1083 -MX23_PAD_LCD_D09__GPIO_1_9 0x1093 -MX23_PAD_LCD_D10__GPIO_1_10 0x10a3 -MX23_PAD_LCD_D11__GPIO_1_11 0x10b3 -MX23_PAD_LCD_D12__GPIO_1_12 0x10c3 -MX23_PAD_LCD_D13__GPIO_1_13 0x10d3 -MX23_PAD_LCD_D14__GPIO_1_14 0x10e3 -MX23_PAD_LCD_D15__GPIO_1_15 0x10f3 -MX23_PAD_LCD_D16__GPIO_1_16 0x1103 -MX23_PAD_LCD_D17__GPIO_1_17 0x1113 -MX23_PAD_LCD_RESET__GPIO_1_18 0x1123 -MX23_PAD_LCD_RS__GPIO_1_19 0x1133 -MX23_PAD_LCD_WR__GPIO_1_20 0x1143 -MX23_PAD_LCD_CS__GPIO_1_21 0x1153 -MX23_PAD_LCD_DOTCK__GPIO_1_22 0x1163 -MX23_PAD_LCD_ENABLE__GPIO_1_23 0x1173 -MX23_PAD_LCD_HSYNC__GPIO_1_24 0x1183 -MX23_PAD_LCD_VSYNC__GPIO_1_25 0x1193 -MX23_PAD_PWM0__GPIO_1_26 0x11a3 -MX23_PAD_PWM1__GPIO_1_27 0x11b3 -MX23_PAD_PWM2__GPIO_1_28 0x11c3 -MX23_PAD_PWM3__GPIO_1_29 0x11d3 -MX23_PAD_PWM4__GPIO_1_30 0x11e3 -MX23_PAD_SSP1_CMD__GPIO_2_0 0x2003 -MX23_PAD_SSP1_DETECT__GPIO_2_1 0x2013 -MX23_PAD_SSP1_DATA0__GPIO_2_2 0x2023 -MX23_PAD_SSP1_DATA1__GPIO_2_3 0x2033 -MX23_PAD_SSP1_DATA2__GPIO_2_4 0x2043 -MX23_PAD_SSP1_DATA3__GPIO_2_5 0x2053 -MX23_PAD_SSP1_SCK__GPIO_2_6 0x2063 -MX23_PAD_ROTARYA__GPIO_2_7 0x2073 -MX23_PAD_ROTARYB__GPIO_2_8 0x2083 -MX23_PAD_EMI_A00__GPIO_2_9 0x2093 -MX23_PAD_EMI_A01__GPIO_2_10 0x20a3 -MX23_PAD_EMI_A02__GPIO_2_11 0x20b3 -MX23_PAD_EMI_A03__GPIO_2_12 0x20c3 -MX23_PAD_EMI_A04__GPIO_2_13 0x20d3 -MX23_PAD_EMI_A05__GPIO_2_14 0x20e3 -MX23_PAD_EMI_A06__GPIO_2_15 0x20f3 -MX23_PAD_EMI_A07__GPIO_2_16 0x2103 -MX23_PAD_EMI_A08__GPIO_2_17 0x2113 -MX23_PAD_EMI_A09__GPIO_2_18 0x2123 -MX23_PAD_EMI_A10__GPIO_2_19 0x2133 -MX23_PAD_EMI_A11__GPIO_2_20 0x2143 -MX23_PAD_EMI_A12__GPIO_2_21 0x2153 -MX23_PAD_EMI_BA0__GPIO_2_22 0x2163 -MX23_PAD_EMI_BA1__GPIO_2_23 0x2173 -MX23_PAD_EMI_CASN__GPIO_2_24 0x2183 -MX23_PAD_EMI_CE0N__GPIO_2_25 0x2193 -MX23_PAD_EMI_CE1N__GPIO_2_26 0x21a3 -MX23_PAD_GPMI_CE1N__GPIO_2_27 0x21b3 -MX23_PAD_GPMI_CE0N__GPIO_2_28 0x21c3 -MX23_PAD_EMI_CKE__GPIO_2_29 0x21d3 -MX23_PAD_EMI_RASN__GPIO_2_30 0x21e3 -MX23_PAD_EMI_WEN__GPIO_2_31 0x21f3 +Valid values for i.MX28/i.MX23 pinmux-id are defined in +arch/arm/boot/dts/imx28-pinfunc.h and arch/arm/boot/dts/imx23-pinfunc.h. +The definitions for the padconfig properties can be found in +arch/arm/boot/dts/mxs-pinfunc.h. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt index 5a02e30..7069a0b 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -72,6 +72,13 @@ Optional properties: /* pin base, nr pins & gpio function */ pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>; +- interrupt-controller : standard interrupt controller binding if using + interrupts for wake-up events for example. In this case pinctrl-single + is set up as a chained interrupt controller and the wake-up interrupts + can be requested by the drivers using request_irq(). + +- #interrupt-cells : standard interrupt binding if using interrupts + This driver assumes that there is only one register for each pin (unless the pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as specified in the pinctrl-bindings.txt document in this directory. @@ -121,6 +128,8 @@ pmx_core: pinmux@4a100040 { reg = <0x4a100040 0x0196>; #address-cells = <1>; #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0xffff>; }; @@ -131,6 +140,8 @@ pmx_wkup: pinmux@4a31e040 { reg = <0x4a31e040 0x0038>; #address-cells = <1>; #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0xffff>; }; diff --git a/Documentation/devicetree/bindings/usb/ux500-usb.txt b/Documentation/devicetree/bindings/usb/ux500-usb.txt index 330d6ec..439a41c 100644 --- a/Documentation/devicetree/bindings/usb/ux500-usb.txt +++ b/Documentation/devicetree/bindings/usb/ux500-usb.txt @@ -15,7 +15,7 @@ Optional properties: Example: usb_per5@a03e0000 { - compatible = "stericsson,db8500-musb", "mentor,musb"; + compatible = "stericsson,db8500-musb"; reg = <0xa03e0000 0x10000>; interrupts = <0 23 0x4>; interrupt-names = "mc"; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt index 323983b..50decf8 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt @@ -12,7 +12,19 @@ Required properties: a) phandle of the gpio controller node. b) pin number within the gpio controller. c) optional flags and pull up/down. - +- clocks: list of clock IDs from SoC clock driver. + a) hdmi: Gate of HDMI IP bus clock. + b) sclk_hdmi: Gate of HDMI special clock. + c) sclk_pixel: Pixel special clock, one of the two possible inputs of + HDMI clock mux. + d) sclk_hdmiphy: HDMI PHY clock output, one of two possible inputs of + HDMI clock mux. + e) mout_hdmi: It is required by the driver to switch between the 2 + parents i.e. sclk_pixel and sclk_hdmiphy. If hdmiphy is stable + after configuration, parent is set to sclk_hdmiphy else + sclk_pixel. +- clock-names: aliases as per driver requirements for above clock IDs: + "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". Example: hdmi { diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt index 3334b0a..7bfde9c 100644 --- a/Documentation/devicetree/bindings/video/exynos_mixer.txt +++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt @@ -10,6 +10,10 @@ Required properties: - reg: physical base address of the mixer and length of memory mapped region. - interrupts: interrupt number to the cpu. +- clocks: list of clock IDs from SoC clock driver. + a) mixer: Gate of Mixer IP bus clock. + b) sclk_hdmi: HDMI Special clock, one of the two possible inputs of + mixer mux. Example: diff --git a/MAINTAINERS b/MAINTAINERS index 7a00136..4d66a03 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -933,7 +933,7 @@ M: Javier Martinez Canillas <javier@dowhile0.org> L: linux-omap@vger.kernel.org L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) S: Maintained -F: arch/arm/mach-omap2/board-igep0020.c +F: arch/arm/boot/dts/omap3-igep* ARM/INCOME PXA270 SUPPORT M: Marek Vasut <marek.vasut@gmail.com> @@ -6125,6 +6125,12 @@ L: linux-omap@vger.kernel.org S: Maintained F: drivers/gpio/gpio-omap.c +OMAP/NEWFLOW NANOBONE MACHINE SUPPORT +M: Mark Jackson <mpfj@newflow.co.uk> +L: linux-omap@vger.kernel.org +S: Maintained +F: arch/arm/boot/dts/am335x-nano.dts + OMFS FILESYSTEM M: Bob Copeland <me@bobcopeland.com> L: linux-karma-devel@lists.sourceforge.net diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 7662b71..d57c1a6 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -40,17 +40,17 @@ dtb-$(CONFIG_ARCH_AT91) += sama5d31ek.dtb dtb-$(CONFIG_ARCH_AT91) += sama5d33ek.dtb dtb-$(CONFIG_ARCH_AT91) += sama5d34ek.dtb dtb-$(CONFIG_ARCH_AT91) += sama5d35ek.dtb - dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb - dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb -dtb-$(CONFIG_ARCH_BCM) += bcm11351-brt.dtb \ +dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm11351-brt.dtb \ bcm28155-ap.dtb +dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \ dove-cubox.dtb \ dove-d2plug.dtb \ + dove-d3plug.dtb \ dove-dove-db.dtb dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ @@ -96,22 +96,25 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-ns2mini.dtb \ kirkwood-nsa310.dtb \ kirkwood-nsa310a.dtb \ + kirkwood-openblocks_a6.dtb \ + kirkwood-openblocks_a7.dtb \ kirkwood-sheevaplug.dtb \ kirkwood-sheevaplug-esata.dtb \ kirkwood-topkick.dtb \ kirkwood-ts219-6281.dtb \ - kirkwood-ts219-6282.dtb \ - kirkwood-openblocks_a6.dtb + kirkwood-ts219-6282.dtb dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb dtb-$(CONFIG_ARCH_MSM) += qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \ armada-370-mirabox.dtb \ armada-370-netgear-rn102.dtb \ + armada-370-netgear-rn104.dtb \ armada-370-rd.dtb \ armada-xp-axpwifiap.dtb \ armada-xp-db.dtb \ armada-xp-gp.dtb \ + armada-xp-matrix.dtb \ armada-xp-openblocks-ax3-4.dtb dtb-$(CONFIG_ARCH_MXC) += \ imx25-karo-tx25.dtb \ @@ -142,8 +145,10 @@ dtb-$(CONFIG_ARCH_MXC) += \ imx6q-sabrelite.dtb \ imx6q-sabresd.dtb \ imx6q-sbc6x.dtb \ + imx6q-udoo.dtb \ imx6q-wandboard.dtb \ imx6sl-evk.dtb \ + vf610-cosmic.dtb \ vf610-twr.dtb dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ imx23-olinuxino.dtb \ @@ -159,6 +164,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ imx28-cfa10057.dtb \ imx28-cfa10058.dtb \ imx28-evk.dtb \ + imx28-m28cu3.dtb \ imx28-m28evk.dtb \ imx28-sps1.dtb \ imx28-tx28.dtb @@ -172,9 +178,15 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ omap3-devkit8000.dtb \ omap3-beagle-xm.dtb \ omap3-evm.dtb \ + omap3-evm-37xx.dtb \ + omap3-n900.dtb \ + omap3-n9.dtb \ + omap3-n950.dtb \ omap3-tobi.dtb \ + omap3-gta04.dtb \ omap3-igep0020.dtb \ omap3-igep0030.dtb \ + omap3-zoom3.dtb \ omap4-panda.dtb \ omap4-panda-a4.dtb \ omap4-panda-es.dtb \ @@ -186,17 +198,24 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ am335x-evmsk.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-nano.dtb \ + am335x-base0033.dtb \ am3517-evm.dtb \ am3517_mt_ventoux.dtb \ - am43x-epos-evm.dtb + am43x-epos-evm.dtb \ + dra7-evm.dtb dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \ - ste-hrefprev60.dtb \ - ste-hrefv60plus.dtb \ + ste-hrefprev60-stuib.dtb \ + ste-hrefprev60-tvk.dtb \ + ste-hrefv60plus-stuib.dtb \ + ste-hrefv60plus-tvk.dtb \ ste-ccu8540.dtb \ ste-ccu9540.dtb dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb +dtb-$(CONFIG_ARCH_S3C64XX) += s3c6410-mini6410.dtb \ + s3c6410-smdk6410.dtb dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \ r7s72100-genmai.dtb \ r8a7740-armadillo800eva.dtb \ @@ -214,7 +233,9 @@ dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \ r8a73a4-ape6evm-reference.dtb \ sh7372-mackerel.dtb dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += emev2-kzm9d.dtb -dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_cyclone5.dtb \ +dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_arria5_socdk.dtb \ + socfpga_cyclone5_socdk.dtb \ + socfpga_cyclone5_sockit.dtb \ socfpga_vt.dtb dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \ spear1340-evb.dtb @@ -236,6 +257,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += \ sun5i-a13-olinuxino.dtb \ sun6i-a31-colombus.dtb \ sun7i-a20-cubieboard2.dtb \ + sun7i-a20-cubietruck.dtb \ sun7i-a20-olinuxino-micro.dtb dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \ tegra20-iris-512.dtb \ @@ -250,7 +272,8 @@ dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \ tegra30-beaver.dtb \ tegra30-cardhu-a02.dtb \ tegra30-cardhu-a04.dtb \ - tegra114-dalmore.dtb + tegra114-dalmore.dtb \ + tegra124-venice2.dtb dtb-$(CONFIG_ARCH_VERSATILE) += versatile-ab.dtb \ versatile-pb.dtb dtb-$(CONFIG_ARCH_U300) += ste-u300.dtb diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts new file mode 100644 index 0000000..b4f95c2 --- /dev/null +++ b/arch/arm/boot/dts/am335x-base0033.dts @@ -0,0 +1,16 @@ +/* + * am335x-base0033.dts - Device Tree file for IGEP AQUILA EXPANSION + * + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "am335x-igep0033.dtsi" + +/ { + model = "IGEP COM AM335x on AQUILA Expansion"; + compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx"; +}; diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 2f66ded..e3f27ec 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -21,177 +21,205 @@ reg = <0x80000000 0x10000000>; /* 256 MB */ }; - am33xx_pinmux: pinmux@44e10800 { + leds { pinctrl-names = "default"; - pinctrl-0 = <&clkout2_pin>; - - user_leds_s0: user_leds_s0 { - pinctrl-single,pins = < - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ - 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ - 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ - 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ - >; - }; + pinctrl-0 = <&user_leds_s0>; - i2c0_pins: pinmux_i2c0_pins { - pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ - >; - }; + compatible = "gpio-leds"; - uart0_pins: pinmux_uart0_pins { - pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ - >; + led@2 { + label = "beaglebone:green:heartbeat"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; }; - clkout2_pin: pinmux_clkout2_pin { - pinctrl-single,pins = < - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; + led@3 { + label = "beaglebone:green:mmc0"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; }; - cpsw_default: cpsw_default { - pinctrl-single,pins = < - /* Slave 1 */ - 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ - 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ - 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ - 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ - 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ - >; + led@4 { + label = "beaglebone:green:usr2"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu0"; + default-state = "off"; }; - cpsw_sleep: cpsw_sleep { - pinctrl-single,pins = < - /* Slave 1 reset value */ - 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; + led@5 { + label = "beaglebone:green:usr3"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; }; + }; - davinci_mdio_default: davinci_mdio_default { - pinctrl-single,pins = < - /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ - >; - }; + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; - davinci_mdio_sleep: davinci_mdio_sleep { - pinctrl-single,pins = < - /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; - }; +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin>; + + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */ + >; }; - ocp { - uart0: serial@44e09000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins>; + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; - status = "okay"; - }; + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; - musb: usb@47400000 { - status = "okay"; + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; - control@44e10000 { - status = "okay"; - }; + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxerr.mii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txen.mii1_txen */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd3.mii1_txd3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd2.mii1_txd2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd1.mii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mii1_txd0.mii1_txd0 */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_txclk.mii1_txclk */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxclk.mii1_rxclk */ + 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */ + 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */ + 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */ + 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */ + >; + }; - usb-phy@47401300 { - status = "okay"; - }; + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; - usb-phy@47401b00 { - status = "okay"; - }; + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; - usb@47401000 { - status = "okay"; - }; + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; - usb@47401800 { - status = "okay"; - dr_mode = "host"; - }; + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */ + >; + }; - dma-controller@07402000 { - status = "okay"; - }; - }; + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + >; + }; +}; - i2c0: i2c@44e0b000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; - status = "okay"; - clock-frequency = <400000>; + status = "okay"; +}; - tps: tps@24 { - reg = <0x24>; - }; +&usb { + status = "okay"; - }; + control@44e10000 { + status = "okay"; }; - leds { - pinctrl-names = "default"; - pinctrl-0 = <&user_leds_s0>; + usb-phy@47401300 { + status = "okay"; + }; - compatible = "gpio-leds"; + usb-phy@47401b00 { + status = "okay"; + }; - led@2 { - label = "beaglebone:green:heartbeat"; - gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; + usb@47401000 { + status = "okay"; + }; - led@3 { - label = "beaglebone:green:mmc0"; - gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; - led@4 { - label = "beaglebone:green:usr2"; - gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; + dma-controller@07402000 { + status = "okay"; + }; +}; - led@5 { - label = "beaglebone:green:usr3"; - gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; }; + }; /include/ "tps65217.dtsi" @@ -260,3 +288,12 @@ pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; }; + +&mmc1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cd-inverted; +}; diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts index 7993c48..94ee427a 100644 --- a/arch/arm/boot/dts/am335x-bone.dts +++ b/arch/arm/boot/dts/am335x-bone.dts @@ -9,3 +9,21 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&ldo3_reg>; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index 197cadf..6b71ad9 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -15,3 +15,64 @@ regulator-max-microvolt = <1800000>; regulator-always-on; }; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; + ti,vcc-aux-disable-is-sleep; +}; + +&am33xx_pinmux { + nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { + pinctrl-single,pins = < + 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */ + 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */ + >; + }; + nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { + pinctrl-single,pins = < + 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ + >; + }; +}; + +&lcdc { + status = "okay"; +}; + +/ { + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index e8ec875..9874294 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -24,324 +24,6 @@ reg = <0x80000000 0x10000000>; /* 256 MB */ }; - am33xx_pinmux: pinmux@44e10800 { - pinctrl-names = "default"; - pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>; - - matrix_keypad_s0: matrix_keypad_s0 { - pinctrl-single,pins = < - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ - 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */ - >; - }; - - volume_keys_s0: volume_keys_s0 { - pinctrl-single,pins = < - 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */ - 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */ - >; - }; - - i2c0_pins: pinmux_i2c0_pins { - pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ - >; - }; - - i2c1_pins: pinmux_i2c1_pins { - pinctrl-single,pins = < - 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */ - 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */ - >; - }; - - uart0_pins: pinmux_uart0_pins { - pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ - >; - }; - - clkout2_pin: pinmux_clkout2_pin { - pinctrl-single,pins = < - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; - }; - - nandflash_pins_s0: nandflash_pins_s0 { - pinctrl-single,pins = < - 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ - >; - }; - - ecap0_pins: backlight_pins { - pinctrl-single,pins = < - 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ - >; - }; - - cpsw_default: cpsw_default { - pinctrl-single,pins = < - /* Slave 1 */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ - 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ - >; - }; - - cpsw_sleep: cpsw_sleep { - pinctrl-single,pins = < - /* Slave 1 reset value */ - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; - }; - - davinci_mdio_default: davinci_mdio_default { - pinctrl-single,pins = < - /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ - >; - }; - - davinci_mdio_sleep: davinci_mdio_sleep { - pinctrl-single,pins = < - /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; - }; - }; - - ocp { - uart0: serial@44e09000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins>; - - status = "okay"; - }; - - i2c0: i2c@44e0b000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; - - status = "okay"; - clock-frequency = <400000>; - - tps: tps@2d { - reg = <0x2d>; - }; - }; - - musb: usb@47400000 { - status = "okay"; - - control@44e10000 { - status = "okay"; - }; - - usb-phy@47401300 { - status = "okay"; - }; - - usb-phy@47401b00 { - status = "okay"; - }; - - usb@47401000 { - status = "okay"; - }; - - usb@47401800 { - status = "okay"; - dr_mode = "host"; - }; - - dma-controller@07402000 { - status = "okay"; - }; - }; - - i2c1: i2c@4802a000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; - - status = "okay"; - clock-frequency = <100000>; - - lis331dlh: lis331dlh@18 { - compatible = "st,lis331dlh", "st,lis3lv02d"; - reg = <0x18>; - Vdd-supply = <&lis3_reg>; - Vdd_IO-supply = <&lis3_reg>; - - st,click-single-x; - st,click-single-y; - st,click-single-z; - st,click-thresh-x = <10>; - st,click-thresh-y = <10>; - st,click-thresh-z = <10>; - st,irq1-click; - st,irq2-click; - st,wakeup-x-lo; - st,wakeup-x-hi; - st,wakeup-y-lo; - st,wakeup-y-hi; - st,wakeup-z-lo; - st,wakeup-z-hi; - st,min-limit-x = <120>; - st,min-limit-y = <120>; - st,min-limit-z = <140>; - st,max-limit-x = <550>; - st,max-limit-y = <550>; - st,max-limit-z = <750>; - }; - - tsl2550: tsl2550@39 { - compatible = "taos,tsl2550"; - reg = <0x39>; - }; - - tmp275: tmp275@48 { - compatible = "ti,tmp275"; - reg = <0x48>; - }; - }; - - elm: elm@48080000 { - status = "okay"; - }; - - epwmss0: epwmss@48300000 { - status = "okay"; - - ecap0: ecap@48300100 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&ecap0_pins>; - }; - }; - - gpmc: gpmc@50000000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&nandflash_pins_s0>; - ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ - nand@0,0 { - reg = <0 0 0>; /* CS0, offset 0 */ - nand-bus-width = <8>; - ti,nand-ecc-opt = "bch8"; - gpmc,device-nand = "true"; - gpmc,device-width = <1>; - gpmc,sync-clk-ps = <0>; - gpmc,cs-on-ns = <0>; - gpmc,cs-rd-off-ns = <44>; - gpmc,cs-wr-off-ns = <44>; - gpmc,adv-on-ns = <6>; - gpmc,adv-rd-off-ns = <34>; - gpmc,adv-wr-off-ns = <44>; - gpmc,we-on-ns = <0>; - gpmc,we-off-ns = <40>; - gpmc,oe-on-ns = <0>; - gpmc,oe-off-ns = <54>; - gpmc,access-ns = <64>; - gpmc,rd-cycle-ns = <82>; - gpmc,wr-cycle-ns = <82>; - gpmc,wait-on-read = "true"; - gpmc,wait-on-write = "true"; - gpmc,bus-turnaround-ns = <0>; - gpmc,cycle2cycle-delay-ns = <0>; - gpmc,clk-activation-ns = <0>; - gpmc,wait-monitoring-ns = <0>; - gpmc,wr-access-ns = <40>; - gpmc,wr-data-mux-bus-ns = <0>; - - #address-cells = <1>; - #size-cells = <1>; - elm_id = <&elm>; - - /* MTD partition table */ - partition@0 { - label = "SPL1"; - reg = <0x00000000 0x000020000>; - }; - - partition@1 { - label = "SPL2"; - reg = <0x00020000 0x00020000>; - }; - - partition@2 { - label = "SPL3"; - reg = <0x00040000 0x00020000>; - }; - - partition@3 { - label = "SPL4"; - reg = <0x00060000 0x00020000>; - }; - - partition@4 { - label = "U-boot"; - reg = <0x00080000 0x001e0000>; - }; - - partition@5 { - label = "environment"; - reg = <0x00260000 0x00020000>; - }; - - partition@6 { - label = "Kernel"; - reg = <0x00280000 0x00500000>; - }; - - partition@7 { - label = "File-System"; - reg = <0x00780000 0x0F880000>; - }; - }; - }; - }; - vbat: fixedregulator@0 { compatible = "regulator-fixed"; regulator-name = "vbat"; @@ -403,10 +85,447 @@ brightness-levels = <0 51 53 56 62 75 101 152 255>; default-brightness-level = <8>; }; + + panel { + compatible = "ti,tilcdc,panel"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins_s0>; + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + + display-timings { + 800x480p62 { + clock-frequency = <30000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <39>; + hback-porch = <39>; + hsync-len = <47>; + vback-porch = <29>; + vfront-porch = <13>; + vsync-len = <2>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "AM335x-EVM"; + ti,audio-codec = <&tlv320aic3106>; + ti,mcasp-controller = <&mcasp1>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "LINE1L", "Line In", + "LINE1R", "Line In"; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>; + + matrix_keypad_s0: matrix_keypad_s0 { + pinctrl-single,pins = < + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */ + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */ + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */ + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */ + >; + }; + + volume_keys_s0: volume_keys_s0 { + pinctrl-single,pins = < + 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */ + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */ + 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; + + nandflash_pins_s0: nandflash_pins_s0 { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + + ecap0_pins: backlight_pins { + pinctrl-single,pins = < + 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + lcd_pins_s0: lcd_pins_s0 { + pinctrl-single,pins = < + 0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */ + 0x24 0x01 /* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */ + 0x28 0x01 /* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */ + 0x2c 0x01 /* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */ + 0x30 0x01 /* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */ + 0x34 0x01 /* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */ + 0x38 0x01 /* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */ + 0x3c 0x01 /* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */ + 0xa0 0x00 /* lcd_data0.lcd_data0, OUTPUT | MODE0 */ + 0xa4 0x00 /* lcd_data1.lcd_data1, OUTPUT | MODE0 */ + 0xa8 0x00 /* lcd_data2.lcd_data2, OUTPUT | MODE0 */ + 0xac 0x00 /* lcd_data3.lcd_data3, OUTPUT | MODE0 */ + 0xb0 0x00 /* lcd_data4.lcd_data4, OUTPUT | MODE0 */ + 0xb4 0x00 /* lcd_data5.lcd_data5, OUTPUT | MODE0 */ + 0xb8 0x00 /* lcd_data6.lcd_data6, OUTPUT | MODE0 */ + 0xbc 0x00 /* lcd_data7.lcd_data7, OUTPUT | MODE0 */ + 0xc0 0x00 /* lcd_data8.lcd_data8, OUTPUT | MODE0 */ + 0xc4 0x00 /* lcd_data9.lcd_data9, OUTPUT | MODE0 */ + 0xc8 0x00 /* lcd_data10.lcd_data10, OUTPUT | MODE0 */ + 0xcc 0x00 /* lcd_data11.lcd_data11, OUTPUT | MODE0 */ + 0xd0 0x00 /* lcd_data12.lcd_data12, OUTPUT | MODE0 */ + 0xd4 0x00 /* lcd_data13.lcd_data13, OUTPUT | MODE0 */ + 0xd8 0x00 /* lcd_data14.lcd_data14, OUTPUT | MODE0 */ + 0xdc 0x00 /* lcd_data15.lcd_data15, OUTPUT | MODE0 */ + 0xe0 0x00 /* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */ + 0xe4 0x00 /* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */ + 0xe8 0x00 /* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */ + 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */ + >; + }; + + am335x_evm_audio_pins: am335x_evm_audio_pins { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */ + 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@2d { + reg = <0x2d>; + }; +}; + +&usb { + status = "okay"; + + control@44e10000 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb-phy@47401b00 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@07402000 { + status = "okay"; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + status = "okay"; + clock-frequency = <100000>; + + lis331dlh: lis331dlh@18 { + compatible = "st,lis331dlh", "st,lis3lv02d"; + reg = <0x18>; + Vdd-supply = <&lis3_reg>; + Vdd_IO-supply = <&lis3_reg>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + st,min-limit-x = <120>; + st,min-limit-y = <120>; + st,min-limit-z = <140>; + st,max-limit-x = <550>; + st,max-limit-y = <550>; + st,max-limit-z = <750>; + }; + + tsl2550: tsl2550@39 { + compatible = "taos,tsl2550"; + reg = <0x39>; + }; + + tmp275: tmp275@48 { + compatible = "ti,tmp275"; + reg = <0x48>; + }; + + tlv320aic3106: tlv320aic3106@1b { + compatible = "ti,tlv320aic3106"; + reg = <0x1b>; + status = "okay"; + + /* Regulators */ + AVDD-supply = <&vaux2_reg>; + IOVDD-supply = <&vaux2_reg>; + DRVDD-supply = <&vaux2_reg>; + DVDD-supply = <&vbat>; + }; +}; + +&lcdc { + status = "okay"; +}; + +&elm { + status = "okay"; +}; + +&epwmss0 { + status = "okay"; + + ecap0: ecap@48300100 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins>; + }; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins_s0>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + elm_id = <&elm>; + + /* MTD partition table */ + partition@0 { + label = "SPL1"; + reg = <0x00000000 0x000020000>; + }; + + partition@1 { + label = "SPL2"; + reg = <0x00020000 0x00020000>; + }; + + partition@2 { + label = "SPL3"; + reg = <0x00040000 0x00020000>; + }; + + partition@3 { + label = "SPL4"; + reg = <0x00060000 0x00020000>; + }; + + partition@4 { + label = "U-boot"; + reg = <0x00080000 0x001e0000>; + }; + + partition@5 { + label = "environment"; + reg = <0x00260000 0x00020000>; + }; + + partition@6 { + label = "Kernel"; + reg = <0x00280000 0x00500000>; + }; + + partition@7 { + label = "File-System"; + reg = <0x00780000 0x0F880000>; + }; + }; }; #include "tps65910.dtsi" +&mcasp1 { + pinctrl-names = "default"; + pinctrl-0 = <&am335x_evm_audio_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializers */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 2 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + &tps { vcc1-supply = <&vbat>; vcc2-supply = <&vbat>; @@ -477,6 +596,8 @@ }; vmmc_reg: regulator@12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; regulator-always-on; }; }; @@ -517,3 +638,17 @@ ti,adc-channels = <4 5 6 7>; }; }; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmc_reg>; + bus-width = <4>; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 4f339fa..03febf8 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -31,210 +31,6 @@ reg = <0x80000000 0x10000000>; /* 256 MB */ }; - am33xx_pinmux: pinmux@44e10800 { - pinctrl-names = "default"; - pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>; - - user_leds_s0: user_leds_s0 { - pinctrl-single,pins = < - 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */ - 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */ - 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */ - 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */ - >; - }; - - gpio_keys_s0: gpio_keys_s0 { - pinctrl-single,pins = < - 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */ - 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */ - 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ - 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */ - >; - }; - - i2c0_pins: pinmux_i2c0_pins { - pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ - >; - }; - - uart0_pins: pinmux_uart0_pins { - pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ - >; - }; - - clkout2_pin: pinmux_clkout2_pin { - pinctrl-single,pins = < - 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; - }; - - ecap2_pins: backlight_pins { - pinctrl-single,pins = < - 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */ - >; - }; - - cpsw_default: cpsw_default { - pinctrl-single,pins = < - /* Slave 1 */ - 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ - 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ - 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ - 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ - 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ - 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ - - /* Slave 2 */ - 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */ - 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ - 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ - 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ - 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ - >; - }; - - cpsw_sleep: cpsw_sleep { - pinctrl-single,pins = < - /* Slave 1 reset value */ - 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) - - /* Slave 2 reset value*/ - 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; - }; - - davinci_mdio_default: davinci_mdio_default { - pinctrl-single,pins = < - /* MDIO */ - 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ - 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ - >; - }; - - davinci_mdio_sleep: davinci_mdio_sleep { - pinctrl-single,pins = < - /* MDIO reset value */ - 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) - 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) - >; - }; - }; - - ocp { - uart0: serial@44e09000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins>; - - status = "okay"; - }; - - i2c0: i2c@44e0b000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; - - status = "okay"; - clock-frequency = <400000>; - - tps: tps@2d { - reg = <0x2d>; - }; - - lis331dlh: lis331dlh@18 { - compatible = "st,lis331dlh", "st,lis3lv02d"; - reg = <0x18>; - Vdd-supply = <&lis3_reg>; - Vdd_IO-supply = <&lis3_reg>; - - st,click-single-x; - st,click-single-y; - st,click-single-z; - st,click-thresh-x = <10>; - st,click-thresh-y = <10>; - st,click-thresh-z = <10>; - st,irq1-click; - st,irq2-click; - st,wakeup-x-lo; - st,wakeup-x-hi; - st,wakeup-y-lo; - st,wakeup-y-hi; - st,wakeup-z-lo; - st,wakeup-z-hi; - st,min-limit-x = <120>; - st,min-limit-y = <120>; - st,min-limit-z = <140>; - st,max-limit-x = <550>; - st,max-limit-y = <550>; - st,max-limit-z = <750>; - }; - }; - - musb: usb@47400000 { - status = "okay"; - - control@44e10000 { - status = "okay"; - }; - - usb-phy@47401300 { - status = "okay"; - }; - - usb@47401000 { - status = "okay"; - }; - }; - - epwmss2: epwmss@48304000 { - status = "okay"; - - ecap2: ecap@48304100 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&ecap2_pins>; - }; - }; - }; - vbat: fixedregulator@0 { compatible = "regulator-fixed"; regulator-name = "vbat"; @@ -319,6 +115,240 @@ brightness-levels = <0 58 61 66 75 90 125 170 255>; default-brightness-level = <8>; }; + + sound { + compatible = "ti,da830-evm-audio"; + ti,model = "AM335x-EVMSK"; + ti,audio-codec = <&tlv320aic3106>; + ti,mcasp-controller = <&mcasp1>; + ti,codec-clock-rate = <24576000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT"; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>; + + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */ + 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */ + 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */ + 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */ + >; + }; + + gpio_keys_s0: gpio_keys_s0 { + pinctrl-single,pins = < + 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_oen_ren.gpio2_3 */ + 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_advn_ale.gpio2_2 */ + 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */ + 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ben0_cle.gpio2_5 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; + + ecap2_pins: backlight_pins { + pinctrl-single,pins = < + 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rctl */ + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd3.rgmii1_td3 */ + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd2.rgmii1_td2 */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */ + 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rgmii1_tclk */ + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rgmii1_rclk */ + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd3.rgmii1_rd3 */ + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd2.rgmii1_rd2 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */ + + /* Slave 2 */ + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */ + 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */ + 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */ + 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */ + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */ + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */ + 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */ + 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */ + 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */ + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */ + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */ + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + + /* Slave 2 reset value*/ + 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + mcasp1_pins: mcasp1_pins { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */ + 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@2d { + reg = <0x2d>; + }; + + lis331dlh: lis331dlh@18 { + compatible = "st,lis331dlh", "st,lis3lv02d"; + reg = <0x18>; + Vdd-supply = <&lis3_reg>; + Vdd_IO-supply = <&lis3_reg>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + st,min-limit-x = <120>; + st,min-limit-y = <120>; + st,min-limit-z = <140>; + st,max-limit-x = <550>; + st,max-limit-y = <550>; + st,max-limit-z = <750>; + }; + + tlv320aic3106: tlv320aic3106@1b { + compatible = "ti,tlv320aic3106"; + reg = <0x1b>; + status = "okay"; + + /* Regulators */ + AVDD-supply = <&vaux2_reg>; + IOVDD-supply = <&vaux2_reg>; + DRVDD-supply = <&vaux2_reg>; + DVDD-supply = <&vbat>; + }; +}; + +&usb { + status = "okay"; + + control@44e10000 { + status = "okay"; + }; + + usb-phy@47401300 { + status = "okay"; + }; + + usb@47401000 { + status = "okay"; + }; +}; + +&epwmss2 { + status = "okay"; + + ecap2: ecap@48304100 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap2_pins>; + }; }; #include "tps65910.dtsi" @@ -393,6 +423,8 @@ }; vmmc_reg: regulator@12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; regulator-always-on; }; }; @@ -419,3 +451,37 @@ phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii-txid"; }; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmc_reg>; + bus-width = <4>; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; + +&gpio0 { + ti,no-reset-on-init; +}; + +&mcasp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcasp1_pins>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializers */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 2 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi new file mode 100644 index 0000000..6196244 --- /dev/null +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi @@ -0,0 +1,278 @@ +/* + * am335x-igep0033.dtsi - Device Tree file for IGEP COM AQUILA AM335x + * + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vdd1_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins>; + + compatible = "gpio-leds"; + + led@0 { + label = "com:green:user"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + vbat: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + vmmc: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&am33xx_pinmux { + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + nandflash_pins: pinmux_nandflash_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + leds_pins: pinmux_leds_pins { + pinctrl-single,pins = < + 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + >; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + elm_id = <&elm>; + + /* MTD partition table */ + partition@0 { + label = "SPL"; + reg = <0x00000000 0x000080000>; + }; + + partition@1 { + label = "U-boot"; + reg = <0x00080000 0x001e0000>; + }; + + partition@2 { + label = "U-Boot Env"; + reg = <0x00260000 0x00020000>; + }; + + partition@3 { + label = "Kernel"; + reg = <0x00280000 0x00500000>; + }; + + partition@4 { + label = "File System"; + reg = <0x00780000 0x007880000>; + }; + }; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + clock-frequency = <400000>; + + tps: tps@2d { + reg = <0x2d>; + }; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmc>; + bus-width = <4>; +}; + +&uart0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; +}; + +#include "tps65910.dtsi" + +&tps { + vcc1-supply = <&vbat>; + vcc2-supply = <&vbat>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vrtc_reg: regulator@0 { + regulator-always-on; + }; + + vio_reg: regulator@1 { + regulator-always-on; + }; + + vdd1_reg: regulator@2 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1312500>; + regulator-boot-on; + regulator-always-on; + }; + + vdd2_reg: regulator@3 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd3_reg: regulator@4 { + regulator-always-on; + }; + + vdig1_reg: regulator@5 { + regulator-always-on; + }; + + vdig2_reg: regulator@6 { + regulator-always-on; + }; + + vpll_reg: regulator@7 { + regulator-always-on; + }; + + vdac_reg: regulator@8 { + regulator-always-on; + }; + + vaux1_reg: regulator@9 { + regulator-always-on; + }; + + vaux2_reg: regulator@10 { + regulator-always-on; + }; + + vaux33_reg: regulator@11 { + regulator-always-on; + }; + + vmmc_reg: regulator@12 { + regulator-always-on; + }; + }; +}; + diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts new file mode 100644 index 0000000..9907b49 --- /dev/null +++ b/arch/arm/boot/dts/am335x-nano.dts @@ -0,0 +1,431 @@ +/* + * Copyright (C) 2013 Newflow Ltd - http://www.newflow.co.uk/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + model = "Newflow AM335x NanoBone"; + compatible = "ti,am33xx"; + + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + leds { + compatible = "gpio-leds"; + + led@0 { + label = "nanobone:green:usr1"; + gpios = <&gpio1 5 0>; + default-state = "off"; + }; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&misc_pins>; + + misc_pins: misc_pins { + pinctrl-single,pins = < + 0x15c (PIN_OUTPUT | MUX_MODE7) /* spi0_cs0.gpio0_5 */ + >; + }; + + gpmc_pins: gpmc_pins { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x20 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad8.gpmc_ad8 */ + 0x24 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad9.gpmc_ad9 */ + 0x28 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad10.gpmc_ad10 */ + 0x2c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad11.gpmc_ad11 */ + 0x30 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad12.gpmc_ad12 */ + 0x34 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad13.gpmc_ad13 */ + 0x38 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad14.gpmc_ad14 */ + 0x3c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad15.gpmc_ad15 */ + + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x80 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn1.gpmc_csn1 */ + 0x84 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn2.gpmc_csn2 */ + 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn3.gpmc_csn3 */ + + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0_cle.gpmc_ben0_cle */ + + 0xa4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data1.gpmc_a1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data2.gpmc_a2 */ + 0xac (PIN_OUTPUT | MUX_MODE1) /* lcd_data3.gpmc_a3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE1) /* lcd_data4.gpmc_a4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data5.gpmc_a5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data6.gpmc_a6 */ + 0xbc (PIN_OUTPUT | MUX_MODE1) /* lcd_data7.gpmc_a7 */ + + 0xe0 (PIN_OUTPUT | MUX_MODE1) /* lcd_vsync.gpmc_a8 */ + 0xe4 (PIN_OUTPUT | MUX_MODE1) /* lcd_hsync.gpmc_a9 */ + 0xe8 (PIN_OUTPUT | MUX_MODE1) /* lcd_pclk.gpmc_a10 */ + >; + }; + + i2c0_pins: i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + uart0_pins: uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + uart1_pins: uart1_pins { + pinctrl-single,pins = < + 0x178 (PIN_OUTPUT | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */ + 0x17c (PIN_OUTPUT | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */ + 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + 0x184 (PIN_OUTPUT | MUX_MODE0) /* uart1_txd.uart1_txd */ + >; + }; + + uart2_pins: uart2_pins { + pinctrl-single,pins = < + 0xc0 (PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_data8.gpio2[14] */ + 0xc4 (PIN_OUTPUT | MUX_MODE7) /* lcd_data9.gpio2[15] */ + 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */ + 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */ + >; + }; + + uart3_pins: uart3_pins { + pinctrl-single,pins = < + 0xc8 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data10.uart3_ctsn */ + 0xcc (PIN_OUTPUT | MUX_MODE6) /* lcd_data11.uart3_rtsn */ + 0x160 (PIN_INPUT | MUX_MODE1) /* spi0_cs1.uart3_rxd */ + 0x164 (PIN_OUTPUT | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */ + >; + }; + + uart4_pins: uart4_pins { + pinctrl-single,pins = < + 0xd0 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data12.uart4_ctsn */ + 0xd4 (PIN_OUTPUT | MUX_MODE6) /* lcd_data13.uart4_rtsn */ + 0x168 (PIN_INPUT | MUX_MODE1) /* uart0_ctsn.uart4_rxd */ + 0x16c (PIN_OUTPUT | MUX_MODE1) /* uart0_rtsn.uart4_txd */ + >; + }; + + uart5_pins: uart5_pins { + pinctrl-single,pins = < + 0xd8 (PIN_INPUT | MUX_MODE4) /* lcd_data14.uart5_rxd */ + 0x144 (PIN_OUTPUT | MUX_MODE3) /* rmiii1_refclk.uart5_txd */ + >; + }; + + mmc1_pins: mmc1_pins { + pinctrl-single,pins = < + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + 0x1e8 (PIN_INPUT_PULLUP | MUX_MODE7) /* emu1.gpio3[8] */ + 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7) /* mcasp0_aclkr.gpio3[18] */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; + rts-gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>; + rs485-rts-active-high; + rs485-rx-during-tx; + rs485-rts-delay = <1 1>; + linux,rs485-enabled-at-boot-time; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; + rts-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>; + rs485-rts-active-high; + rs485-rts-delay = <1 1>; + linux,rs485-enabled-at-boot-time; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&uart5_pins>; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + gpio@20 { + compatible = "mcp,mcp23017"; + reg = <0x20>; + }; + + tps: tps@24 { + reg = <0x24>; + }; + + eeprom@53 { + compatible = "mcp,24c02"; + reg = <0x53>; + pagesize = <8>; + }; + + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + }; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + status = "okay"; + gpmc,num-waitpins = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&gpmc_pins>; + + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x08000000>; /* CS0: NOR 128M */ + + nor@0,0 { + reg = <0 0x00000000 0x08000000>; + compatible = "cfi-flash"; + linux,mtd-name = "spansion,s29gl010p11t"; + bank-width = <2>; + + gpmc,mux-add-data = <2>; + + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <160>; + gpmc,cs-wr-off-ns = <160>; + gpmc,adv-on-ns = <10>; + gpmc,adv-rd-off-ns = <30>; + gpmc,adv-wr-off-ns = <30>; + gpmc,oe-on-ns = <40>; + gpmc,oe-off-ns = <160>; + gpmc,we-on-ns = <40>; + gpmc,we-off-ns = <160>; + gpmc,rd-cycle-ns = <160>; + gpmc,wr-cycle-ns = <160>; + gpmc,access-ns = <150>; + gpmc,page-burst-access-ns = <10>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-delay-ns = <20>; + gpmc,wr-data-mux-bus-ns = <70>; + gpmc,wr-access-ns = <80>; + + #address-cells = <1>; + #size-cells = <1>; + + /* + MTD partition table + =================== + +------------+-->0x00000000-> U-Boot start + | | + | |-->0x000BFFFF-> U-Boot end + | |-->0x000C0000-> ENV1 start + | | + | |-->0x000DFFFF-> ENV1 end + | |-->0x000E0000-> ENV2 start + | | + | |-->0x000FFFFF-> ENV2 end + | |-->0x00100000-> Kernel start + | | + | |-->0x004FFFFF-> Kernel end + | |-->0x00500000-> File system start + | | + | |-->0x014FFFFF-> File system end + | |-->0x01500000-> User data start + | | + | |-->0x03FFFFFF-> User data end + | |-->0x04000000-> Data storage start + | | + +------------+-->0x08000000-> NOR end (Free end) + */ + partition@0 { + label = "boot"; + reg = <0x00000000 0x000c0000>; /* 768KB */ + }; + + partition@1 { + label = "env1"; + reg = <0x000c0000 0x00020000>; /* 128KB */ + }; + + partition@2 { + label = "env2"; + reg = <0x000e0000 0x00020000>; /* 128KB */ + }; + + partition@3 { + label = "kernel"; + reg = <0x00100000 0x00400000>; /* 4MB */ + }; + + partition@4 { + label = "rootfs"; + reg = <0x00500000 0x01000000>; /* 16MB */ + }; + + partition@5 { + label = "user"; + reg = <0x01500000 0x02b00000>; /* 43MB */ + }; + + partition@6 { + label = "data"; + reg = <0x04000000 0x04000000>; /* 64MB */ + }; + }; +}; + +&mac { + dual_emac = <1>; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + dual_emac_res_vlan = <1>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + dual_emac_res_vlan = <2>; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&ldo4_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + bus-width = <4>; + cd-gpios = <&gpio3 8 0>; + wp-gpios = <&gpio3 18 0>; +}; + +#include "tps65217.dtsi" + +&tps { + regulators { + dcdc1_reg: regulator@0 { + /* +1.5V voltage with ±4% tolerance */ + regulator-min-microvolt = <1450000>; + regulator-max-microvolt = <1550000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <915000>; + regulator-max-microvolt = <1140000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <915000>; + regulator-max-microvolt = <1140000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + /* +1.8V voltage with ±4% tolerance */ + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <1870000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + /* +3.3V voltage with ±4% tolerance */ + regulator-min-microvolt = <3175000>; + regulator-max-microvolt = <3430000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + /* +1.8V voltage with ±4% tolerance */ + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <1870000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + /* +3.3V voltage with ±4% tolerance */ + regulator-min-microvolt = <3175000>; + regulator-max-microvolt = <3430000>; + regulator-boot-on; + regulator-always-on; + }; + }; +}; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index f9c5da9..fcb9c8e 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -18,6 +18,9 @@ interrupt-parent = <&intc>; aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; @@ -30,6 +33,8 @@ usb1 = &usb1; phy0 = &usb0_phy; phy1 = &usb1_phy; + ethernet0 = &cpsw_emac0; + ethernet1 = &cpsw_emac1; }; cpus { @@ -57,6 +62,11 @@ }; }; + pmu { + compatible = "arm,cortex-a8-pmu"; + interrupts = <3>; + }; + /* * The soc node represents the soc top level view. It is uses for IPs * that are not memory mapped in the MPU view or for the MPU itself. @@ -100,13 +110,25 @@ reg = <0x48200000 0x1000>; }; + edma: edma@49000000 { + compatible = "ti,edma3"; + ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; + reg = <0x49000000 0x10000>, + <0x44e10f90 0x10>; + interrupts = <12 13 14>; + #dma-cells = <1>; + dma-channels = <64>; + ti,edma-regions = <4>; + ti,edma-slots = <256>; + }; + gpio0: gpio@44e07000 { compatible = "ti,omap4-gpio"; ti,hwmods = "gpio1"; gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x44e07000 0x1000>; interrupts = <96>; }; @@ -117,7 +139,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x4804c000 0x1000>; interrupts = <98>; }; @@ -128,7 +150,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x481ac000 0x1000>; interrupts = <32>; }; @@ -139,7 +161,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x481ae000 0x1000>; interrupts = <62>; }; @@ -228,6 +250,50 @@ status = "disabled"; }; + mmc1: mmc@48060000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + ti,needs-special-hs-handling; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; + interrupts = <64>; + interrupt-parent = <&intc>; + reg = <0x48060000 0x1000>; + status = "disabled"; + }; + + mmc2: mmc@481d8000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + dmas = <&edma 2 + &edma 3>; + dma-names = "tx", "rx"; + interrupts = <28>; + interrupt-parent = <&intc>; + reg = <0x481d8000 0x1000>; + status = "disabled"; + }; + + mmc3: mmc@47810000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + interrupts = <29>; + interrupt-parent = <&intc>; + reg = <0x47810000 0x1000>; + status = "disabled"; + }; + + hwspinlock: spinlock@480ca000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x480ca000 0x1000>; + ti,hwmods = "spinlock"; + }; + wdt2: wdt@44e35000 { compatible = "ti,omap3-wdt"; ti,hwmods = "wd_timer2"; @@ -323,6 +389,11 @@ interrupts = <65>; ti,spi-num-cs = <2>; ti,hwmods = "spi0"; + dmas = <&edma 16 + &edma 17 + &edma 18 + &edma 19>; + dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; @@ -334,6 +405,11 @@ interrupts = <125>; ti,spi-num-cs = <2>; ti,hwmods = "spi1"; + dmas = <&edma 42 + &edma 43 + &edma 44 + &edma 45>; + dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; @@ -346,7 +422,7 @@ ti,hwmods = "usb_otg_hs"; status = "disabled"; - ctrl_mod: control@44e10000 { + usb_ctrl_mod: control@44e10000 { compatible = "ti,am335x-usb-ctrl-module"; reg = <0x44e10620 0x10 0x44e10648 0x4>; @@ -359,7 +435,7 @@ reg = <0x47401300 0x100>; reg-names = "phy"; status = "disabled"; - ti,ctrl_mod = <&ctrl_mod>; + ti,ctrl_mod = <&usb_ctrl_mod>; }; usb0: usb@47401000 { @@ -407,7 +483,7 @@ reg = <0x47401b00 0x100>; reg-names = "phy"; status = "disabled"; - ti,ctrl_mod = <&ctrl_mod>; + ti,ctrl_mod = <&usb_ctrl_mod>; }; usb1: usb@47401800 { @@ -607,6 +683,7 @@ reg = <0x44d00000 0x4000 /* M3 UMEM */ 0x44d80000 0x2000>; /* M3 DMEM */ ti,hwmods = "wkup_m3"; + ti,no-reset-on-init; }; elm: elm@48080000 { @@ -617,6 +694,15 @@ status = "disabled"; }; + lcdc: lcdc@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + status = "disabled"; + }; + tscadc: tscadc@44e0d000 { compatible = "ti,am3359-tscadc"; reg = <0x44e0d000 0x1000>; @@ -637,6 +723,7 @@ gpmc: gpmc@50000000 { compatible = "ti,am3352-gpmc"; ti,hwmods = "gpmc"; + ti,no-idle-on-init; reg = <0x50000000 0x2000>; interrupts = <100>; gpmc,num-cs = <7>; @@ -645,5 +732,59 @@ #size-cells = <1>; status = "disabled"; }; + + sham: sham@53100000 { + compatible = "ti,omap4-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x200>; + interrupts = <109>; + dmas = <&edma 36>; + dma-names = "rx"; + }; + + aes: aes@53500000 { + compatible = "ti,omap4-aes"; + ti,hwmods = "aes"; + reg = <0x53500000 0xa0>; + interrupts = <103>; + dmas = <&edma 6>, + <&edma 5>; + dma-names = "tx", "rx"; + }; + + mcasp0: mcasp@48038000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp0"; + reg = <0x48038000 0x2000>, + <0x46000000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <80>, <81>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 8>, + <&edma 9>; + dma-names = "tx", "rx"; + }; + + mcasp1: mcasp@4803C000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp1"; + reg = <0x4803C000 0x2000>, + <0x46400000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <82>, <83>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 10>, + <&edma 11>; + dma-names = "tx", "rx"; + }; + + rng: rng@48310000 { + compatible = "ti,omap4-rng"; + ti,hwmods = "rng"; + reg = <0x48310000 0x2000>; + interrupts = <111>; + }; }; }; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index ddc1df7..974d103 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -18,12 +18,21 @@ aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; serial0 = &uart0; + ethernet0 = &cpsw_emac0; + ethernet1 = &cpsw_emac1; }; cpus { + #address-cells = <1>; + #size-cells = <0>; cpu@0 { compatible = "arm,cortex-a9"; + device_type = "cpu"; + reg = <0>; }; }; @@ -35,16 +44,100 @@ <0x48240100 0x0100>; }; + l2-cache-controller@48242000 { + compatible = "arm,pl310-cache"; + reg = <0x48242000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + am43xx_pinmux: pinmux@44e10800 { + compatible = "pinctrl-single"; + reg = <0x44e10800 0x31c>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0xffffffff>; + }; + ocp { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; + ti,hwmods = "l3_main"; + + edma: edma@49000000 { + compatible = "ti,edma3"; + ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; + reg = <0x49000000 0x10000>, + <0x44e10f90 0x10>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + dma-channels = <64>; + ti,edma-regions = <4>; + ti,edma-slots = <256>; + }; uart0: serial@44e09000 { compatible = "ti,am4372-uart","ti,omap2-uart"; reg = <0x44e09000 0x2000>; interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart1"; + }; + + uart1: serial@48022000 { + compatible = "ti,am4372-uart","ti,omap2-uart"; + reg = <0x48022000 0x2000>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart2"; + status = "disabled"; + }; + + uart2: serial@48024000 { + compatible = "ti,am4372-uart","ti,omap2-uart"; + reg = <0x48024000 0x2000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart3"; + status = "disabled"; + }; + + uart3: serial@481a6000 { + compatible = "ti,am4372-uart","ti,omap2-uart"; + reg = <0x481a6000 0x2000>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart4"; + status = "disabled"; + }; + + uart4: serial@481a8000 { + compatible = "ti,am4372-uart","ti,omap2-uart"; + reg = <0x481a8000 0x2000>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart5"; + status = "disabled"; + }; + + uart5: serial@481aa000 { + compatible = "ti,am4372-uart","ti,omap2-uart"; + reg = <0x481aa000 0x2000>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart6"; + status = "disabled"; + }; + + mailbox: mailbox@480C8000 { + compatible = "ti,omap4-mailbox"; + reg = <0x480C8000 0x200>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mailbox"; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <8>; + ti,mbox-names = "wkup_m3"; + ti,mbox-data = <0 0 0 0>; + status = "disabled"; }; timer1: timer@44e31000 { @@ -52,17 +145,523 @@ reg = <0x44e31000 0x400>; interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; ti,timer-alwon; + ti,hwmods = "timer1"; }; timer2: timer@48040000 { compatible = "ti,am4372-timer","ti,am335x-timer"; reg = <0x48040000 0x400>; interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer2"; + }; + + timer3: timer@48042000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x48042000 0x400>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer3"; + status = "disabled"; + }; + + timer4: timer@48044000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x48044000 0x400>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + ti,timer-pwm; + ti,hwmods = "timer4"; + status = "disabled"; + }; + + timer5: timer@48046000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x48046000 0x400>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + ti,timer-pwm; + ti,hwmods = "timer5"; + status = "disabled"; + }; + + timer6: timer@48048000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x48048000 0x400>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + ti,timer-pwm; + ti,hwmods = "timer6"; + status = "disabled"; + }; + + timer7: timer@4804a000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x4804a000 0x400>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + ti,timer-pwm; + ti,hwmods = "timer7"; + status = "disabled"; + }; + + timer8: timer@481c1000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x481c1000 0x400>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer8"; + status = "disabled"; + }; + + timer9: timer@4833d000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x4833d000 0x400>; + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer9"; + status = "disabled"; + }; + + timer10: timer@4833f000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x4833f000 0x400>; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer10"; + status = "disabled"; + }; + + timer11: timer@48341000 { + compatible = "ti,am4372-timer","ti,am335x-timer"; + reg = <0x48341000 0x400>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer11"; + status = "disabled"; }; counter32k: counter@44e86000 { compatible = "ti,am4372-counter32k","ti,omap-counter32k"; reg = <0x44e86000 0x40>; + ti,hwmods = "counter_32k"; + }; + + rtc@44e3e000 { + compatible = "ti,am4372-rtc","ti,da830-rtc"; + reg = <0x44e3e000 0x1000>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "rtc"; + status = "disabled"; + }; + + wdt@44e35000 { + compatible = "ti,am4372-wdt","ti,omap3-wdt"; + reg = <0x44e35000 0x1000>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "wd_timer2"; + }; + + gpio0: gpio@44e07000 { + compatible = "ti,am4372-gpio","ti,omap4-gpio"; + reg = <0x44e07000 0x1000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + ti,hwmods = "gpio1"; + status = "disabled"; + }; + + gpio1: gpio@4804c000 { + compatible = "ti,am4372-gpio","ti,omap4-gpio"; + reg = <0x4804c000 0x1000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + ti,hwmods = "gpio2"; + status = "disabled"; + }; + + gpio2: gpio@481ac000 { + compatible = "ti,am4372-gpio","ti,omap4-gpio"; + reg = <0x481ac000 0x1000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + ti,hwmods = "gpio3"; + status = "disabled"; + }; + + gpio3: gpio@481ae000 { + compatible = "ti,am4372-gpio","ti,omap4-gpio"; + reg = <0x481ae000 0x1000>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + ti,hwmods = "gpio4"; + status = "disabled"; + }; + + gpio4: gpio@48320000 { + compatible = "ti,am4372-gpio","ti,omap4-gpio"; + reg = <0x48320000 0x1000>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + ti,hwmods = "gpio5"; + status = "disabled"; + }; + + gpio5: gpio@48322000 { + compatible = "ti,am4372-gpio","ti,omap4-gpio"; + reg = <0x48322000 0x1000>; + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + ti,hwmods = "gpio6"; + status = "disabled"; + }; + + i2c0: i2c@44e0b000 { + compatible = "ti,am4372-i2c","ti,omap4-i2c"; + reg = <0x44e0b000 0x1000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "i2c1"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@4802a000 { + compatible = "ti,am4372-i2c","ti,omap4-i2c"; + reg = <0x4802a000 0x1000>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "i2c2"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@4819c000 { + compatible = "ti,am4372-i2c","ti,omap4-i2c"; + reg = <0x4819c000 0x1000>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "i2c3"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi0: spi@48030000 { + compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; + reg = <0x48030000 0x400>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "spi0"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + mmc1: mmc@48060000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x48060000 0x1000>; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + mmc2: mmc@481d8000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x481d8000 0x1000>; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + dmas = <&edma 2 + &edma 3>; + dma-names = "tx", "rx"; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + mmc3: mmc@47810000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x47810000 0x1000>; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + spi1: spi@481a0000 { + compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; + reg = <0x481a0000 0x400>; + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "spi1"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi2: spi@481a2000 { + compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; + reg = <0x481a2000 0x400>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "spi2"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi3: spi@481a4000 { + compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; + reg = <0x481a4000 0x400>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "spi3"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi4: spi@48345000 { + compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; + reg = <0x48345000 0x400>; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "spi4"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + mac: ethernet@4a100000 { + compatible = "ti,am4372-cpsw","ti,cpsw"; + reg = <0x4a100000 0x800 + 0x4a101200 0x100>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <1>; + ti,hwmods = "cpgmac0"; + status = "disabled"; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + ranges; + + davinci_mdio: mdio@4a101000 { + compatible = "ti,am4372-mdio","ti,davinci_mdio"; + reg = <0x4a101000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + status = "disabled"; + }; + + cpsw_emac0: slave@4a100200 { + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + + cpsw_emac1: slave@4a100300 { + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + + epwmss0: epwmss@48300000 { + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "epwmss0"; + status = "disabled"; + + ecap0: ecap@48300100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; + status = "disabled"; + }; + + ehrpwm0: ehrpwm@48300200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48300200 0x80>; + ti,hwmods = "ehrpwm0"; + status = "disabled"; + }; + }; + + epwmss1: epwmss@48302000 { + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + reg = <0x48302000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "epwmss1"; + status = "disabled"; + + ecap1: ecap@48302100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48302100 0x80>; + ti,hwmods = "ecap1"; + status = "disabled"; + }; + + ehrpwm1: ehrpwm@48302200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48302200 0x80>; + ti,hwmods = "ehrpwm1"; + status = "disabled"; + }; + }; + + epwmss2: epwmss@48304000 { + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + reg = <0x48304000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "epwmss2"; + status = "disabled"; + + ecap2: ecap@48304100 { + compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + reg = <0x48304100 0x80>; + ti,hwmods = "ecap2"; + status = "disabled"; + }; + + ehrpwm2: ehrpwm@48304200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48304200 0x80>; + ti,hwmods = "ehrpwm2"; + status = "disabled"; + }; + }; + + epwmss3: epwmss@48306000 { + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + reg = <0x48306000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "epwmss3"; + status = "disabled"; + + ehrpwm3: ehrpwm@48306200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48306200 0x80>; + ti,hwmods = "ehrpwm3"; + status = "disabled"; + }; + }; + + epwmss4: epwmss@48308000 { + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + reg = <0x48308000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "epwmss4"; + status = "disabled"; + + ehrpwm4: ehrpwm@48308200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x48308200 0x80>; + ti,hwmods = "ehrpwm4"; + status = "disabled"; + }; + }; + + epwmss5: epwmss@4830a000 { + compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; + reg = <0x4830a000 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "epwmss5"; + status = "disabled"; + + ehrpwm5: ehrpwm@4830a200 { + compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + reg = <0x4830a200 0x80>; + ti,hwmods = "ehrpwm5"; + status = "disabled"; + }; + }; + + sham: sham@53100000 { + compatible = "ti,omap5-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x300>; + dmas = <&edma 36>; + dma-names = "rx"; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + }; + + aes: aes@53501000 { + compatible = "ti,omap4-aes"; + ti,hwmods = "aes"; + reg = <0x53501000 0xa0>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&edma 6 + &edma 5>; + dma-names = "tx", "rx"; + }; + + des: des@53701000 { + compatible = "ti,omap4-des"; + ti,hwmods = "des"; + reg = <0x53701000 0xa0>; + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&edma 34 + &edma 33>; + dma-names = "tx", "rx"; + }; + + mcasp0: mcasp@48038000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp0"; + reg = <0x48038000 0x2000>, + <0x46000000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <80>, <81>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 8>, + <&edma 9>; + dma-names = "tx", "rx"; + }; + + mcasp1: mcasp@4803C000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp1"; + reg = <0x4803C000 0x2000>, + <0x46400000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <82>, <83>; + interrupts-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 10>, + <&edma 11>; + dma-names = "tx", "rx"; }; }; }; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index 74174d4..fbf9c4c 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -11,8 +11,176 @@ /dts-v1/; #include "am4372.dtsi" +#include <dt-bindings/pinctrl/am43xx.h> +#include <dt-bindings/gpio/gpio.h> / { model = "TI AM43x EPOS EVM"; compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43"; + + vmmcsd_fixed: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + }; + + am43xx_pinmux: pinmux@44e10800 { + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + }; + + matrix_keypad: matrix_keypad@0 { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */ + &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */ + &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */ + &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */ + + col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */ + &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */ + &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */ + &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */ + + linux,keymap = <0x00000201 /* P1 */ + 0x01000204 /* P4 */ + 0x02000207 /* P7 */ + 0x0300020a /* NUMERIC_STAR */ + 0x00010202 /* P2 */ + 0x01010205 /* P5 */ + 0x02010208 /* P8 */ + 0x03010200 /* P0 */ + 0x00020203 /* P3 */ + 0x01020206 /* P6 */ + 0x02020209 /* P9 */ + 0x0302020b /* NUMERIC_POUND */ + 0x00030067 /* UP */ + 0x0103006a /* RIGHT */ + 0x0203006c /* DOWN */ + 0x03030069>; /* LEFT */ + }; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <16>; + phy-mode = "rmii"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rmii"; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + at24@50 { + compatible = "at24,24c256"; + pagesize = <64>; + reg = <0x50>; + }; + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>; + + x-size = <1024>; + y-size = <768>; + }; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts new file mode 100644 index 0000000..b0b32f5 --- /dev/null +++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts @@ -0,0 +1,193 @@ +/* + * Device Tree file for NETGEAR ReadyNAS 104 + * + * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +/dts-v1/; + +#include "armada-370.dtsi" + +/ { + model = "NETGEAR ReadyNAS 104"; + compatible = "netgear,readynas-104", "marvell,armada370", "marvell,armada-370-xp"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; /* 512 MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000 + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; + + pcie-controller { + status = "okay"; + + /* Connected to FL1009 USB 3.0 controller */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + + /* Connected to Marvell 88SE9215 SATA controller */ + pcie@2,0 { + /* Port 1, Lane 0 */ + status = "okay"; + }; + }; + + internal-regs { + serial@12000 { + clock-frequency = <200000000>; + status = "okay"; + }; + + pinctrl { + poweroff: poweroff { + marvell,pins = "mpp60"; + marvell,function = "gpio"; + }; + + backup_key_pin: backup-key-pin { + marvell,pins = "mpp52"; + marvell,function = "gpio"; + }; + + power_key_pin: power-key-pin { + marvell,pins = "mpp62"; + marvell,function = "gpio"; + }; + + backup_led_pin: backup-led-pin { + marvell,pins = "mpp63"; + marvell,function = "gpo"; + }; + + power_led_pin: power-led-pin { + marvell,pins = "mpp64"; + marvell,function = "gpio"; + }; + + reset_key_pin: reset-key-pin { + marvell,pins = "mpp65"; + marvell,function = "gpio"; + }; + }; + + mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + + ethernet@74000 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; + }; + + usb@50000 { + status = "okay"; + }; + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + clock-frequency = <100000>; + status = "okay"; + + g762: g762@3e { + compatible = "gmt,g762"; + reg = <0x3e>; + clocks = <&g762_clk>; /* input clock */ + fan_gear_mode = <0>; + fan_startv = <1>; + pwm_polarity = <0>; + }; + }; + }; + }; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + g762_clk: fixedclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <8192>; + }; + }; + + gpio_leds { + compatible = "gpio-leds"; + pinctrl-0 = <&backup_led_pin &power_led_pin>; + pinctrl-names = "default"; + + blue_backup_led { + label = "rn104:blue:backup"; + gpios = <&gpio1 31 0>; /* GPIO 63 Active High */ + default-state = "off"; + }; + + blue_power_led { + label = "rn104:blue:pwr"; + gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */ + linux,default-trigger = "keep"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&backup_key_pin + &power_key_pin + &reset_key_pin>; + pinctrl-names = "default"; + + button@1 { + label = "Backup Button"; + linux,code = <133>; /* KEY_COPY */ + gpios = <&gpio1 20 1>; + }; + + button@2 { + label = "Power Button"; + linux,code = <116>; /* KEY_POWER */ + gpios = <&gpio1 30 0>; + }; + + button@3 { + label = "Reset Button"; + linux,code = <0x198>; /* KEY_RESTART */ + gpios = <&gpio2 1 1>; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + pinctrl-0 = <&poweroff>; + pinctrl-names = "default"; + gpios = <&gpio1 28 1>; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 1de2dae..00d6a79 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -113,6 +113,7 @@ #interrupt-cells = <1>; #size-cells = <1>; interrupt-controller; + msi-controller; }; coherency-fabric@20200 { @@ -137,6 +138,14 @@ status = "disabled"; }; + coredivclk: corediv-clock@18740 { + compatible = "marvell,armada-370-corediv-clock"; + reg = <0x18740 0xc>; + #clock-cells = <1>; + clocks = <&mainpll>; + clock-output-names = "nand"; + }; + timer@20300 { reg = <0x20300 0x30>, <0x21040 0x30>; interrupts = <37>, <38>, <39>, <40>, <5>, <6>; @@ -176,7 +185,6 @@ i2c0: i2c@11000 { compatible = "marvell,mv64xxx-i2c"; - reg = <0x11000 0x20>; #address-cells = <1>; #size-cells = <0>; interrupts = <31>; @@ -187,7 +195,6 @@ i2c1: i2c@11100 { compatible = "marvell,mv64xxx-i2c"; - reg = <0x11100 0x20>; #address-cells = <1>; #size-cells = <0>; interrupts = <32>; @@ -252,4 +259,13 @@ }; }; + + clocks { + /* 2 GHz fixed main PLL */ + mainpll: mainpll { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <2000000000>; + }; + }; }; diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi index e134d7a..7a4b82e 100644 --- a/arch/arm/boot/dts/armada-370.dtsi +++ b/arch/arm/boot/dts/armada-370.dtsi @@ -44,6 +44,7 @@ #address-cells = <3>; #size-cells = <2>; + msi-parent = <&mpic>; bus-range = <0x00 0xff>; ranges = @@ -218,6 +219,14 @@ }; }; + i2c0: i2c@11000 { + reg = <0x11000 0x20>; + }; + + i2c1: i2c@11100 { + reg = <0x11100 0x20>; + }; + usb@50000 { clocks = <&coreclk 0>; }; diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/armada-xp-matrix.dts new file mode 100644 index 0000000..e47c49e --- /dev/null +++ b/arch/arm/boot/dts/armada-xp-matrix.dts @@ -0,0 +1,75 @@ +/* + * Device Tree file for Marvell Armada XP Matrix board + * + * Copyright (C) 2013 Marvell + * + * Lior Amsalem <alior@marvell.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; +#include "armada-xp-mv78460.dtsi" + +/ { + model = "Marvell Armada XP Matrix Board"; + compatible = "marvell,axp-matrix", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { + device_type = "memory"; + reg = <0 0x00000000 0 0x80000000>; /* 2 GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + + internal-regs { + serial@12000 { + clock-frequency = <250000000>; + status = "okay"; + }; + serial@12100 { + clock-frequency = <250000000>; + status = "okay"; + }; + serial@12200 { + clock-frequency = <250000000>; + status = "okay"; + }; + serial@12300 { + clock-frequency = <250000000>; + status = "okay"; + }; + + sata@a0000 { + nr-ports = <2>; + status = "okay"; + }; + + ethernet@30000 { + status = "okay"; + phy-mode = "sgmii"; + }; + + pcie-controller { + status = "okay"; + + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + }; + + usb@50000 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi index 0358a33..3f5e612 100644 --- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi @@ -57,6 +57,7 @@ #address-cells = <3>; #size-cells = <2>; + msi-parent = <&mpic>; bus-range = <0x00 0xff>; ranges = diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index 0e82c50..3e9fd13 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi @@ -58,6 +58,7 @@ #address-cells = <3>; #size-cells = <2>; + msi-parent = <&mpic>; bus-range = <0x00 0xff>; ranges = diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi index e82c1b8..31ba6d8 100644 --- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi @@ -74,6 +74,7 @@ #address-cells = <3>; #size-cells = <2>; + msi-parent = <&mpic>; bus-range = <0x00 0xff>; ranges = diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi index 3058522..281c644 100644 --- a/arch/arm/boot/dts/armada-xp.dtsi +++ b/arch/arm/boot/dts/armada-xp.dtsi @@ -147,6 +147,16 @@ }; }; + i2c0: i2c@11000 { + compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c"; + reg = <0x11000 0x100>; + }; + + i2c1: i2c@11100 { + compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c"; + reg = <0x11100 0x100>; + }; + usb@50000 { clocks = <&gateclk 18>; }; diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi index 1373546..cb2c010 100644 --- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi +++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi @@ -96,7 +96,6 @@ }; spi0: spi@fffc8000 { - status = "okay"; cs-gpios = <0>, <&pioC 11 0>, <0>, <0>; mtd_dataflash@0 { compatible = "atmel,at45", "atmel,dataflash"; diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index 9fb7ffd..6224f9f 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -437,6 +437,9 @@ compatible = "atmel,at91sam9g45-ssc"; reg = <0xf0010000 0x4000>; interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>; + dmas = <&dma 0 AT91_DMA_CFG_PER_ID(21)>, + <&dma 0 AT91_DMA_CFG_PER_ID(22)>; + dma-names = "tx", "rx"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; status = "disabled"; diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index 27a9352..e9487f6 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -38,9 +38,18 @@ status = "okay"; }; + ssc0: ssc@f0010000 { + status = "okay"; + }; + i2c0: i2c@f8010000 { status = "okay"; + wm8904: codec@1a { + compatible = "wm8904"; + reg = <0x1a>; + }; + qt1070: keyboard@1b { compatible = "qt1070"; reg = <0x1b>; @@ -82,6 +91,13 @@ <AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; }; }; + + sound { + pinctrl_pck0_as_audio_mck: pck0_as_audio_mck { + atmel,pins = + <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; }; spi0: spi@f0000000 { @@ -142,4 +158,22 @@ gpio-key,wakeup; }; }; + + sound { + compatible = "atmel,asoc-wm8904"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_audio_mck>; + + atmel,model = "wm8904 @ AT91SAM9N12"; + atmel,audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "IN2L", "Line In Jack", + "IN2R", "Line In Jack", + "Mic", "MICBIAS", + "IN1L", "Mic"; + + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8904>; + }; }; diff --git a/arch/arm/boot/dts/atlas6.dtsi b/arch/arm/boot/dts/atlas6.dtsi index 6db4f81..a49032c 100644 --- a/arch/arm/boot/dts/atlas6.dtsi +++ b/arch/arm/boot/dts/atlas6.dtsi @@ -65,6 +65,11 @@ compatible = "sirf,prima2-rsc"; reg = <0x88020000 0x1000>; }; + + cphifbg@88030000 { + compatible = "sirf,prima2-cphifbg"; + reg = <0x88030000 0x1000>; + }; }; mem-iobg { @@ -75,10 +80,17 @@ memory-controller@90000000 { compatible = "sirf,prima2-memc"; - reg = <0x90000000 0x10000>; + reg = <0x90000000 0x2000>; interrupts = <27>; clocks = <&clks 5>; }; + + memc-monitor { + compatible = "sirf,prima2-memcmon"; + reg = <0x90002000 0x200>; + interrupts = <4>; + clocks = <&clks 32>; + }; }; disp-iobg { @@ -120,6 +132,20 @@ }; }; + graphics2d-iobg { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0xa0000000 0xa0000000 0x8000000>; + + ble@a0000000 { + compatible = "sirf,atlas6-ble"; + reg = <0xa0000000 0x2000>; + interrupts = <5>; + clocks = <&clks 33>; + }; + }; + dsp-iobg { compatible = "simple-bus"; #address-cells = <1>; @@ -271,6 +297,11 @@ compatible = "sirf,prima2-spi"; reg = <0xb0170000 0x10000>; interrupts = <16>; + sirf,spi-num-chipselects = <1>; + sirf,spi-dma-rx-channel = <12>; + sirf,spi-dma-tx-channel = <13>; + #address-cells = <1>; + #size-cells = <0>; clocks = <&clks 20>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/bcm11351-brt.dts b/arch/arm/boot/dts/bcm11351-brt.dts index 9d36eb4..23cd16d 100644 --- a/arch/arm/boot/dts/bcm11351-brt.dts +++ b/arch/arm/boot/dts/bcm11351-brt.dts @@ -40,6 +40,7 @@ sdio4: sdio@3f1b0000 { max-frequency = <48000000>; + cd-gpios = <&gpio 14 0>; status = "okay"; }; diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi index 05a5aab..b0c0610 100644 --- a/arch/arm/boot/dts/bcm11351.dtsi +++ b/arch/arm/boot/dts/bcm11351.dtsi @@ -49,6 +49,36 @@ reg-io-width = <4>; }; + uart@3e001000 { + compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; + status = "disabled"; + reg = <0x3e001000 0x1000>; + clock-frequency = <13000000>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + uart@3e002000 { + compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; + status = "disabled"; + reg = <0x3e002000 0x1000>; + clock-frequency = <13000000>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + uart@3e003000 { + compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; + status = "disabled"; + reg = <0x3e003000 0x1000>; + clock-frequency = <13000000>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + L2: l2-cache { compatible = "brcm,bcm11351-a2-pl310-cache"; reg = <0x3ff20000 0x1000>; @@ -68,31 +98,47 @@ clock-frequency = <32768>; }; + gpio: gpio@35003000 { + compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio"; + reg = <0x35003000 0x800>; + interrupts = + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-controller; + interrupt-controller; + }; + sdio1: sdio@3f180000 { compatible = "brcm,kona-sdhci"; reg = <0x3f180000 0x10000>; - interrupts = <0x0 77 0x4>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; sdio2: sdio@3f190000 { compatible = "brcm,kona-sdhci"; reg = <0x3f190000 0x10000>; - interrupts = <0x0 76 0x4>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; sdio3: sdio@3f1a0000 { compatible = "brcm,kona-sdhci"; reg = <0x3f1a0000 0x10000>; - interrupts = <0x0 74 0x4>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; sdio4: sdio@3f1b0000 { compatible = "brcm,kona-sdhci"; reg = <0x3f1b0000 0x10000>; - interrupts = <0x0 73 0x4>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts index 96ae67a..08e47c2 100644 --- a/arch/arm/boot/dts/bcm28155-ap.dts +++ b/arch/arm/boot/dts/bcm28155-ap.dts @@ -40,6 +40,7 @@ sdio4: sdio@3f1b0000 { max-frequency = <48000000>; + cd-gpios = <&gpio 14 0>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/dove-cm-a510.dts b/arch/arm/boot/dts/dove-cm-a510.dts index 61a8062..50c0d69 100644 --- a/arch/arm/boot/dts/dove-cm-a510.dts +++ b/arch/arm/boot/dts/dove-cm-a510.dts @@ -1,6 +1,6 @@ /dts-v1/; -/include/ "dove.dtsi" +#include "dove.dtsi" / { model = "Compulab CM-A510"; diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts index 022646e..8349a24 100644 --- a/arch/arm/boot/dts/dove-cubox.dts +++ b/arch/arm/boot/dts/dove-cubox.dts @@ -1,6 +1,6 @@ /dts-v1/; -/include/ "dove.dtsi" +#include "dove.dtsi" / { model = "SolidRun CuBox"; @@ -99,18 +99,12 @@ silabs,pll-master; }; - clkout1 { - reg = <1>; - silabs,drive-strength = <8>; - silabs,multisynth-source = <1>; - silabs,clock-source = <0>; - silabs,pll-master; - }; - clkout2 { reg = <2>; + silabs,drive-strength = <8>; silabs,multisynth-source = <1>; silabs,clock-source = <0>; + silabs,pll-master; }; }; }; @@ -132,3 +126,11 @@ reg = <0>; }; }; + +&audio1 { + status = "okay"; + clocks = <&gate_clk 13>, <&si5351 2>; + clock-names = "internal", "extclk"; + pinctrl-0 = <&pmx_audio1_i2s1_spdifo &pmx_audio1_extclk>; + pinctrl-names = "default"; +}; diff --git a/arch/arm/boot/dts/dove-d2plug.dts b/arch/arm/boot/dts/dove-d2plug.dts index e2222ce..c11d363 100644 --- a/arch/arm/boot/dts/dove-d2plug.dts +++ b/arch/arm/boot/dts/dove-d2plug.dts @@ -1,6 +1,6 @@ /dts-v1/; -/include/ "dove.dtsi" +#include "dove.dtsi" / { model = "Globalscale D2Plug"; diff --git a/arch/arm/boot/dts/dove-d3plug.dts b/arch/arm/boot/dts/dove-d3plug.dts new file mode 100644 index 0000000..f5f59bb --- /dev/null +++ b/arch/arm/boot/dts/dove-d3plug.dts @@ -0,0 +1,103 @@ +/dts-v1/; + +#include "dove.dtsi" + +/ { + model = "Globalscale D3Plug"; + compatible = "globalscale,d3plug", "marvell,dove"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x40000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>; + pinctrl-names = "default"; + + wlan-act { + label = "wlan-act"; + gpios = <&gpio0 0 1>; + }; + + wlan-ap { + label = "wlan-ap"; + gpios = <&gpio0 1 1>; + }; + + status { + label = "status"; + gpios = <&gpio0 2 1>; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + usb_power: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 8 0>; + pinctrl-0 = <&pmx_gpio_8>; + pinctrl-names = "default"; + }; + }; +}; + +&uart0 { status = "okay"; }; +&sata0 { status = "okay"; }; +&i2c0 { status = "okay"; }; + +/* Samsung M8G2F eMMC */ +&sdio0 { + status = "okay"; + non-removable; + bus-width = <4>; +}; + +/* Marvell SD8787 WLAN/BT */ +&sdio1 { + status = "okay"; + non-removable; +}; + +&spi0 { + status = "okay"; + + /* spi0.0: 2M Flash Macronix MX25L1605D */ + spi-flash@0 { + compatible = "st,m25l1605d"; + spi-max-frequency = <86000000>; + reg = <0>; + }; +}; + +&pcie { + status = "okay"; + /* Fresco Logic USB3.0 xHCI controller */ + pcie-port@0 { + status = "okay"; + reset-gpios = <&gpio0 26 1>; + reset-delay-us = <20000>; + pinctrl-0 = <&pmx_camera_gpio>; + pinctrl-names = "default"; + }; + /* Mini-PCIe slot */ + pcie-port@1 { + status = "okay"; + reset-gpios = <&gpio0 25 1>; + }; +}; diff --git a/arch/arm/boot/dts/dove-dove-db.dts b/arch/arm/boot/dts/dove-dove-db.dts index e5a920b..bb725dc 100644 --- a/arch/arm/boot/dts/dove-dove-db.dts +++ b/arch/arm/boot/dts/dove-dove-db.dts @@ -1,6 +1,6 @@ /dts-v1/; -/include/ "dove.dtsi" +#include "dove.dtsi" / { model = "Marvell DB-MV88AP510-BP Development Board"; diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index cc27916..113a8bc 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -1,8 +1,11 @@ /include/ "skeleton.dtsi" +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + / { compatible = "marvell,dove"; model = "Marvell Armada 88AP510 SoC"; + interrupt-parent = <&intc>; aliases { gpio0 = &gpio0; @@ -27,482 +30,576 @@ marvell,tauros2-cache-features = <0>; }; - soc@f1000000 { - compatible = "simple-bus"; - #address-cells = <1>; + mbus { + compatible = "marvell,dove-mbus", "marvell,mbus", "simple-bus"; + #address-cells = <2>; #size-cells = <1>; - interrupt-parent = <&intc>; - - ranges = <0xc8000000 0xc8000000 0x0100000 /* CESA SRAM 1M */ - 0xe0000000 0xe0000000 0x8000000 /* PCIe0 Mem 128M */ - 0xe8000000 0xe8000000 0x8000000 /* PCIe1 Mem 128M */ - 0xf0000000 0xf0000000 0x0100000 /* ScratchPad 1M */ - 0x00000000 0xf1000000 0x1000000 /* SB/NB regs 16M */ - 0xf2000000 0xf2000000 0x0100000 /* PCIe0 I/O 1M */ - 0xf2100000 0xf2100000 0x0100000 /* PCIe0 I/O 1M */ - 0xf8000000 0xf8000000 0x8000000>; /* BootROM 128M */ - - timer: timer@20300 { - compatible = "marvell,orion-timer"; - reg = <0x20300 0x20>; - interrupt-parent = <&bridge_intc>; - interrupts = <1>, <2>; - clocks = <&core_clk 0>; - }; - - intc: main-interrupt-ctrl@20200 { - compatible = "marvell,orion-intc"; - interrupt-controller; - #interrupt-cells = <1>; - reg = <0x20200 0x10>, <0x20210 0x10>; - }; - - bridge_intc: bridge-interrupt-ctrl@20110 { - compatible = "marvell,orion-bridge-intc"; - interrupt-controller; - #interrupt-cells = <1>; - reg = <0x20110 0x8>; - interrupts = <0>; - marvell,#interrupts = <5>; - }; - - core_clk: core-clocks@d0214 { - compatible = "marvell,dove-core-clock"; - reg = <0xd0214 0x4>; - #clock-cells = <1>; - }; - - gate_clk: clock-gating-ctrl@d0038 { - compatible = "marvell,dove-gating-clock"; - reg = <0xd0038 0x4>; - clocks = <&core_clk 0>; - #clock-cells = <1>; - }; - - thermal: thermal-diode@d001c { - compatible = "marvell,dove-thermal"; - reg = <0xd001c 0x0c>, <0xd005c 0x08>; - }; - - uart0: serial@12000 { - compatible = "ns16550a"; - reg = <0x12000 0x100>; - reg-shift = <2>; - interrupts = <7>; - clocks = <&core_clk 0>; - status = "disabled"; - }; - - uart1: serial@12100 { - compatible = "ns16550a"; - reg = <0x12100 0x100>; - reg-shift = <2>; - interrupts = <8>; - clocks = <&core_clk 0>; - pinctrl-0 = <&pmx_uart1>; - pinctrl-names = "default"; - status = "disabled"; - }; - - uart2: serial@12200 { - compatible = "ns16550a"; - reg = <0x12000 0x100>; - reg-shift = <2>; - interrupts = <9>; - clocks = <&core_clk 0>; + controller = <&mbusc>; + pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256M MEM space */ + pcie-io-aperture = <0xf2000000 0x00200000>; /* 2M I/O space */ + + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x0100000 /* MBUS regs 1M */ + MBUS_ID(0xf0, 0x02) 0 0xf1800000 0x1000000 /* AXI regs 16M */ + MBUS_ID(0x01, 0xfd) 0 0xf8000000 0x8000000 /* BootROM 128M */ + MBUS_ID(0x03, 0x01) 0 0xc8000000 0x0100000 /* CESA SRAM 1M */ + MBUS_ID(0x0d, 0x00) 0 0xf0000000 0x0100000>; /* PMU SRAM 1M */ + + pcie: pcie-controller { + compatible = "marvell,dove-pcie"; status = "disabled"; - }; - - uart3: serial@12300 { - compatible = "ns16550a"; - reg = <0x12100 0x100>; - reg-shift = <2>; - interrupts = <10>; - clocks = <&core_clk 0>; - status = "disabled"; - }; - - gpio0: gpio-ctrl@d0400 { - compatible = "marvell,orion-gpio"; - #gpio-cells = <2>; - gpio-controller; - reg = <0xd0400 0x20>; - ngpios = <32>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = <12>, <13>, <14>, <60>; - }; - - gpio1: gpio-ctrl@d0420 { - compatible = "marvell,orion-gpio"; - #gpio-cells = <2>; - gpio-controller; - reg = <0xd0420 0x20>; - ngpios = <32>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = <61>; - }; - - gpio2: gpio-ctrl@e8400 { - compatible = "marvell,orion-gpio"; - #gpio-cells = <2>; - gpio-controller; - reg = <0xe8400 0x0c>; - ngpios = <8>; - }; - - pinctrl: pin-ctrl@d0200 { - compatible = "marvell,dove-pinctrl"; - reg = <0xd0200 0x10>; - clocks = <&gate_clk 22>; - - pmx_gpio_0: pmx-gpio-0 { - marvell,pins = "mpp0"; - marvell,function = "gpio"; - }; - - pmx_gpio_1: pmx-gpio-1 { - marvell,pins = "mpp1"; - marvell,function = "gpio"; - }; - - pmx_gpio_2: pmx-gpio-2 { - marvell,pins = "mpp2"; - marvell,function = "gpio"; - }; - - pmx_gpio_3: pmx-gpio-3 { - marvell,pins = "mpp3"; - marvell,function = "gpio"; + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&intc>; + bus-range = <0x00 0xff>; + + ranges = <0x82000000 0x0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x2000 + 0x82000000 0x0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x2000 + 0x82000000 0x1 0x0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 Mem */ + 0x81000000 0x1 0x0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 I/O */ + 0x82000000 0x2 0x0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 Mem */ + 0x81000000 0x2 0x0 MBUS_ID(0x08, 0xe0) 0 1 0>; /* Port 1.0 I/O */ + + pcie-port@0 { + device_type = "pci"; + status = "disabled"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + clocks = <&gate_clk 4>; + marvell,pcie-port = <0>; + + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc 16>; + }; + + pcie-port@1 { + device_type = "pci"; + status = "disabled"; + assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + clocks = <&gate_clk 5>; + marvell,pcie-port = <1>; + + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc 18>; }; - - pmx_gpio_4: pmx-gpio-4 { - marvell,pins = "mpp4"; - marvell,function = "gpio"; - }; - - pmx_gpio_5: pmx-gpio-5 { - marvell,pins = "mpp5"; - marvell,function = "gpio"; - }; - - pmx_gpio_6: pmx-gpio-6 { - marvell,pins = "mpp6"; - marvell,function = "gpio"; - }; - - pmx_gpio_7: pmx-gpio-7 { - marvell,pins = "mpp7"; - marvell,function = "gpio"; - }; - - pmx_gpio_8: pmx-gpio-8 { - marvell,pins = "mpp8"; - marvell,function = "gpio"; - }; - - pmx_gpio_9: pmx-gpio-9 { - marvell,pins = "mpp9"; - marvell,function = "gpio"; - }; - - pmx_gpio_10: pmx-gpio-10 { - marvell,pins = "mpp10"; - marvell,function = "gpio"; - }; - - pmx_gpio_11: pmx-gpio-11 { - marvell,pins = "mpp11"; - marvell,function = "gpio"; - }; - - pmx_gpio_12: pmx-gpio-12 { - marvell,pins = "mpp12"; - marvell,function = "gpio"; - }; - - pmx_gpio_13: pmx-gpio-13 { - marvell,pins = "mpp13"; - marvell,function = "gpio"; - }; - - pmx_gpio_14: pmx-gpio-14 { - marvell,pins = "mpp14"; - marvell,function = "gpio"; - }; - - pmx_gpio_15: pmx-gpio-15 { - marvell,pins = "mpp15"; - marvell,function = "gpio"; - }; - - pmx_gpio_16: pmx-gpio-16 { - marvell,pins = "mpp16"; - marvell,function = "gpio"; - }; - - pmx_gpio_17: pmx-gpio-17 { - marvell,pins = "mpp17"; - marvell,function = "gpio"; - }; - - pmx_gpio_18: pmx-gpio-18 { - marvell,pins = "mpp18"; - marvell,function = "gpio"; - }; - - pmx_gpio_19: pmx-gpio-19 { - marvell,pins = "mpp19"; - marvell,function = "gpio"; - }; - - pmx_gpio_20: pmx-gpio-20 { - marvell,pins = "mpp20"; - marvell,function = "gpio"; - }; - - pmx_gpio_21: pmx-gpio-21 { - marvell,pins = "mpp21"; - marvell,function = "gpio"; - }; - - pmx_camera: pmx-camera { - marvell,pins = "mpp_camera"; - marvell,function = "camera"; - }; - - pmx_camera_gpio: pmx-camera-gpio { - marvell,pins = "mpp_camera"; - marvell,function = "gpio"; - }; - - pmx_sdio0: pmx-sdio0 { - marvell,pins = "mpp_sdio0"; - marvell,function = "sdio0"; - }; - - pmx_sdio0_gpio: pmx-sdio0-gpio { - marvell,pins = "mpp_sdio0"; - marvell,function = "gpio"; - }; - - pmx_sdio1: pmx-sdio1 { - marvell,pins = "mpp_sdio1"; - marvell,function = "sdio1"; - }; - - pmx_sdio1_gpio: pmx-sdio1-gpio { - marvell,pins = "mpp_sdio1"; - marvell,function = "gpio"; - }; - - pmx_audio1_gpio: pmx-audio1-gpio { - marvell,pins = "mpp_audio1"; - marvell,function = "gpio"; - }; - - pmx_spi0: pmx-spi0 { - marvell,pins = "mpp_spi0"; - marvell,function = "spi0"; - }; - - pmx_spi0_gpio: pmx-spi0-gpio { - marvell,pins = "mpp_spi0"; - marvell,function = "gpio"; - }; - - pmx_uart1: pmx-uart1 { - marvell,pins = "mpp_uart1"; - marvell,function = "uart1"; - }; - - pmx_uart1_gpio: pmx-uart1-gpio { - marvell,pins = "mpp_uart1"; - marvell,function = "gpio"; - }; - - pmx_nand: pmx-nand { - marvell,pins = "mpp_nand"; - marvell,function = "nand"; - }; - - pmx_nand_gpo: pmx-nand-gpo { - marvell,pins = "mpp_nand"; - marvell,function = "gpo"; - }; - }; - - spi0: spi-ctrl@10600 { - compatible = "marvell,orion-spi"; - #address-cells = <1>; - #size-cells = <0>; - cell-index = <0>; - interrupts = <6>; - reg = <0x10600 0x28>; - clocks = <&core_clk 0>; - pinctrl-0 = <&pmx_spi0>; - pinctrl-names = "default"; - status = "disabled"; - }; - - spi1: spi-ctrl@14600 { - compatible = "marvell,orion-spi"; - #address-cells = <1>; - #size-cells = <0>; - cell-index = <1>; - interrupts = <5>; - reg = <0x14600 0x28>; - clocks = <&core_clk 0>; - status = "disabled"; - }; - - i2c0: i2c-ctrl@11000 { - compatible = "marvell,mv64xxx-i2c"; - reg = <0x11000 0x20>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <11>; - clock-frequency = <400000>; - timeout-ms = <1000>; - clocks = <&core_clk 0>; - status = "disabled"; }; - ehci0: usb-host@50000 { - compatible = "marvell,orion-ehci"; - reg = <0x50000 0x1000>; - interrupts = <24>; - clocks = <&gate_clk 0>; - status = "okay"; - }; - - ehci1: usb-host@51000 { - compatible = "marvell,orion-ehci"; - reg = <0x51000 0x1000>; - interrupts = <25>; - clocks = <&gate_clk 1>; - status = "okay"; - }; - - sdio0: sdio-host@92000 { - compatible = "marvell,dove-sdhci"; - reg = <0x92000 0x100>; - interrupts = <35>, <37>; - clocks = <&gate_clk 8>; - pinctrl-0 = <&pmx_sdio0>; - pinctrl-names = "default"; - status = "disabled"; - }; - - sdio1: sdio-host@90000 { - compatible = "marvell,dove-sdhci"; - reg = <0x90000 0x100>; - interrupts = <36>, <38>; - clocks = <&gate_clk 9>; - pinctrl-0 = <&pmx_sdio1>; - pinctrl-names = "default"; - status = "disabled"; - }; - - sata0: sata-host@a0000 { - compatible = "marvell,orion-sata"; - reg = <0xa0000 0x2400>; - interrupts = <62>; - clocks = <&gate_clk 3>; - nr-ports = <1>; - status = "disabled"; - }; - - rtc: real-time-clock@d8500 { - compatible = "marvell,orion-rtc"; - reg = <0xd8500 0x20>; - }; - - crypto: crypto-engine@30000 { - compatible = "marvell,orion-crypto"; - reg = <0x30000 0x10000>, - <0xc8000000 0x800>; - reg-names = "regs", "sram"; - interrupts = <31>; - clocks = <&gate_clk 15>; - status = "okay"; - }; - - xor0: dma-engine@60800 { - compatible = "marvell,orion-xor"; - reg = <0x60800 0x100 - 0x60a00 0x100>; - clocks = <&gate_clk 23>; - status = "okay"; - - channel0 { - interrupts = <39>; - dmacap,memcpy; - dmacap,xor; - }; - - channel1 { - interrupts = <40>; - dmacap,memset; - dmacap,memcpy; - dmacap,xor; - }; - }; - - xor1: dma-engine@60900 { - compatible = "marvell,orion-xor"; - reg = <0x60900 0x100 - 0x60b00 0x100>; - clocks = <&gate_clk 24>; - status = "okay"; - - channel0 { - interrupts = <42>; - dmacap,memcpy; - dmacap,xor; - }; - - channel1 { - interrupts = <43>; - dmacap,memset; - dmacap,memcpy; - dmacap,xor; - }; - }; - - mdio: mdio-bus@72004 { - compatible = "marvell,orion-mdio"; + internal-regs { + compatible = "simple-bus"; #address-cells = <1>; - #size-cells = <0>; - reg = <0x72004 0x84>; - interrupts = <30>; - clocks = <&gate_clk 2>; - status = "disabled"; - - ethphy: ethernet-phy { - device-type = "ethernet-phy"; - /* set phy address in board file */ - }; - }; - - eth: ethernet-controller@72000 { - compatible = "marvell,orion-eth"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72000 0x4000>; - clocks = <&gate_clk 2>; - marvell,tx-checksum-limit = <1600>; - status = "disabled"; - - ethernet-port@0 { - device_type = "network"; - compatible = "marvell,orion-eth-port"; - reg = <0>; - interrupts = <29>; - /* overwrite MAC address in bootloader */ - local-mac-address = [00 00 00 00 00 00]; - phy-handle = <ðphy>; + #size-cells = <1>; + ranges = <0x00000000 MBUS_ID(0xf0, 0x01) 0 0x0100000 /* MBUS regs 1M */ + 0x00800000 MBUS_ID(0xf0, 0x02) 0 0x1000000 /* AXI regs 16M */ + 0xffffe000 MBUS_ID(0x03, 0x01) 0 0x0000800 /* CESA SRAM 2k */ + 0xfffff000 MBUS_ID(0x0d, 0x00) 0 0x0000800>; /* PMU SRAM 2k */ + + mbusc: mbus-ctrl@20000 { + compatible = "marvell,mbus-controller"; + reg = <0x20000 0x80>, <0x800100 0x8>; + }; + + timer: timer@20300 { + compatible = "marvell,orion-timer"; + reg = <0x20300 0x20>; + interrupt-parent = <&bridge_intc>; + interrupts = <1>, <2>; + clocks = <&core_clk 0>; + }; + + intc: main-interrupt-ctrl@20200 { + compatible = "marvell,orion-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x20200 0x10>, <0x20210 0x10>; + }; + + bridge_intc: bridge-interrupt-ctrl@20110 { + compatible = "marvell,orion-bridge-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x20110 0x8>; + interrupts = <0>; + marvell,#interrupts = <5>; + }; + + core_clk: core-clocks@d0214 { + compatible = "marvell,dove-core-clock"; + reg = <0xd0214 0x4>; + #clock-cells = <1>; + }; + + gate_clk: clock-gating-ctrl@d0038 { + compatible = "marvell,dove-gating-clock"; + reg = <0xd0038 0x4>; + clocks = <&core_clk 0>; + #clock-cells = <1>; + }; + + thermal: thermal-diode@d001c { + compatible = "marvell,dove-thermal"; + reg = <0xd001c 0x0c>, <0xd005c 0x08>; + }; + + uart0: serial@12000 { + compatible = "ns16550a"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = <7>; + clocks = <&core_clk 0>; + status = "disabled"; + }; + + uart1: serial@12100 { + compatible = "ns16550a"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <8>; + clocks = <&core_clk 0>; + pinctrl-0 = <&pmx_uart1>; + pinctrl-names = "default"; + status = "disabled"; + }; + + uart2: serial@12200 { + compatible = "ns16550a"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = <9>; + clocks = <&core_clk 0>; + status = "disabled"; + }; + + uart3: serial@12300 { + compatible = "ns16550a"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <10>; + clocks = <&core_clk 0>; + status = "disabled"; + }; + + gpio0: gpio-ctrl@d0400 { + compatible = "marvell,orion-gpio"; + #gpio-cells = <2>; + gpio-controller; + reg = <0xd0400 0x20>; + ngpios = <32>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <12>, <13>, <14>, <60>; + }; + + gpio1: gpio-ctrl@d0420 { + compatible = "marvell,orion-gpio"; + #gpio-cells = <2>; + gpio-controller; + reg = <0xd0420 0x20>; + ngpios = <32>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <61>; + }; + + gpio2: gpio-ctrl@e8400 { + compatible = "marvell,orion-gpio"; + #gpio-cells = <2>; + gpio-controller; + reg = <0xe8400 0x0c>; + ngpios = <8>; + }; + + pinctrl: pin-ctrl@d0200 { + compatible = "marvell,dove-pinctrl"; + reg = <0xd0200 0x10>; + clocks = <&gate_clk 22>; + + pmx_gpio_0: pmx-gpio-0 { + marvell,pins = "mpp0"; + marvell,function = "gpio"; + }; + + pmx_gpio_1: pmx-gpio-1 { + marvell,pins = "mpp1"; + marvell,function = "gpio"; + }; + + pmx_gpio_2: pmx-gpio-2 { + marvell,pins = "mpp2"; + marvell,function = "gpio"; + }; + + pmx_gpio_3: pmx-gpio-3 { + marvell,pins = "mpp3"; + marvell,function = "gpio"; + }; + + pmx_gpio_4: pmx-gpio-4 { + marvell,pins = "mpp4"; + marvell,function = "gpio"; + }; + + pmx_gpio_5: pmx-gpio-5 { + marvell,pins = "mpp5"; + marvell,function = "gpio"; + }; + + pmx_gpio_6: pmx-gpio-6 { + marvell,pins = "mpp6"; + marvell,function = "gpio"; + }; + + pmx_gpio_7: pmx-gpio-7 { + marvell,pins = "mpp7"; + marvell,function = "gpio"; + }; + + pmx_gpio_8: pmx-gpio-8 { + marvell,pins = "mpp8"; + marvell,function = "gpio"; + }; + + pmx_gpio_9: pmx-gpio-9 { + marvell,pins = "mpp9"; + marvell,function = "gpio"; + }; + + pmx_gpio_10: pmx-gpio-10 { + marvell,pins = "mpp10"; + marvell,function = "gpio"; + }; + + pmx_gpio_11: pmx-gpio-11 { + marvell,pins = "mpp11"; + marvell,function = "gpio"; + }; + + pmx_gpio_12: pmx-gpio-12 { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_gpio_13: pmx-gpio-13 { + marvell,pins = "mpp13"; + marvell,function = "gpio"; + }; + + pmx_audio1_extclk: pmx-audio1-extclk { + marvell,pins = "mpp13"; + marvell,function = "audio1"; + }; + + pmx_gpio_14: pmx-gpio-14 { + marvell,pins = "mpp14"; + marvell,function = "gpio"; + }; + + pmx_gpio_15: pmx-gpio-15 { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_gpio_16: pmx-gpio-16 { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_gpio_17: pmx-gpio-17 { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; + + pmx_gpio_18: pmx-gpio-18 { + marvell,pins = "mpp18"; + marvell,function = "gpio"; + }; + + pmx_gpio_19: pmx-gpio-19 { + marvell,pins = "mpp19"; + marvell,function = "gpio"; + }; + + pmx_gpio_20: pmx-gpio-20 { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + + pmx_gpio_21: pmx-gpio-21 { + marvell,pins = "mpp21"; + marvell,function = "gpio"; + }; + + pmx_camera: pmx-camera { + marvell,pins = "mpp_camera"; + marvell,function = "camera"; + }; + + pmx_camera_gpio: pmx-camera-gpio { + marvell,pins = "mpp_camera"; + marvell,function = "gpio"; + }; + + pmx_sdio0: pmx-sdio0 { + marvell,pins = "mpp_sdio0"; + marvell,function = "sdio0"; + }; + + pmx_sdio0_gpio: pmx-sdio0-gpio { + marvell,pins = "mpp_sdio0"; + marvell,function = "gpio"; + }; + + pmx_sdio1: pmx-sdio1 { + marvell,pins = "mpp_sdio1"; + marvell,function = "sdio1"; + }; + + pmx_sdio1_gpio: pmx-sdio1-gpio { + marvell,pins = "mpp_sdio1"; + marvell,function = "gpio"; + }; + + pmx_audio1_gpio: pmx-audio1-gpio { + marvell,pins = "mpp_audio1"; + marvell,function = "gpio"; + }; + + pmx_audio1_i2s1_spdifo: pmx-audio1-i2s1-spdifo { + marvell,pins = "mpp_audio1"; + marvell,function = "i2s1/spdifo"; + }; + + pmx_spi0: pmx-spi0 { + marvell,pins = "mpp_spi0"; + marvell,function = "spi0"; + }; + + pmx_spi0_gpio: pmx-spi0-gpio { + marvell,pins = "mpp_spi0"; + marvell,function = "gpio"; + }; + + pmx_uart1: pmx-uart1 { + marvell,pins = "mpp_uart1"; + marvell,function = "uart1"; + }; + + pmx_uart1_gpio: pmx-uart1-gpio { + marvell,pins = "mpp_uart1"; + marvell,function = "gpio"; + }; + + pmx_nand: pmx-nand { + marvell,pins = "mpp_nand"; + marvell,function = "nand"; + }; + + pmx_nand_gpo: pmx-nand-gpo { + marvell,pins = "mpp_nand"; + marvell,function = "gpo"; + }; + }; + + spi0: spi-ctrl@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + interrupts = <6>; + reg = <0x10600 0x28>; + clocks = <&core_clk 0>; + pinctrl-0 = <&pmx_spi0>; + pinctrl-names = "default"; + status = "disabled"; + }; + + spi1: spi-ctrl@14600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + interrupts = <5>; + reg = <0x14600 0x28>; + clocks = <&core_clk 0>; + status = "disabled"; + }; + + i2c0: i2c-ctrl@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <11>; + clock-frequency = <400000>; + timeout-ms = <1000>; + clocks = <&core_clk 0>; + status = "disabled"; + }; + + ehci0: usb-host@50000 { + compatible = "marvell,orion-ehci"; + reg = <0x50000 0x1000>; + interrupts = <24>; + clocks = <&gate_clk 0>; + status = "okay"; + }; + + ehci1: usb-host@51000 { + compatible = "marvell,orion-ehci"; + reg = <0x51000 0x1000>; + interrupts = <25>; + clocks = <&gate_clk 1>; + status = "okay"; + }; + + sdio0: sdio-host@92000 { + compatible = "marvell,dove-sdhci"; + reg = <0x92000 0x100>; + interrupts = <35>, <37>; + clocks = <&gate_clk 8>; + pinctrl-0 = <&pmx_sdio0>; + pinctrl-names = "default"; + status = "disabled"; + }; + + sdio1: sdio-host@90000 { + compatible = "marvell,dove-sdhci"; + reg = <0x90000 0x100>; + interrupts = <36>, <38>; + clocks = <&gate_clk 9>; + pinctrl-0 = <&pmx_sdio1>; + pinctrl-names = "default"; + status = "disabled"; + }; + + sata0: sata-host@a0000 { + compatible = "marvell,orion-sata"; + reg = <0xa0000 0x2400>; + interrupts = <62>; + clocks = <&gate_clk 3>; + nr-ports = <1>; + status = "disabled"; + }; + + rtc: real-time-clock@d8500 { + compatible = "marvell,orion-rtc"; + reg = <0xd8500 0x20>; + }; + + crypto: crypto-engine@30000 { + compatible = "marvell,orion-crypto"; + reg = <0x30000 0x10000>, + <0xffffe000 0x800>; + reg-names = "regs", "sram"; + interrupts = <31>; + clocks = <&gate_clk 15>; + status = "okay"; + }; + + xor0: dma-engine@60800 { + compatible = "marvell,orion-xor"; + reg = <0x60800 0x100 + 0x60a00 0x100>; + clocks = <&gate_clk 23>; + status = "okay"; + + channel0 { + interrupts = <39>; + dmacap,memcpy; + dmacap,xor; + }; + + channel1 { + interrupts = <40>; + dmacap,memcpy; + dmacap,xor; + }; + }; + + xor1: dma-engine@60900 { + compatible = "marvell,orion-xor"; + reg = <0x60900 0x100 + 0x60b00 0x100>; + clocks = <&gate_clk 24>; + status = "okay"; + + channel0 { + interrupts = <42>; + dmacap,memcpy; + dmacap,xor; + }; + + channel1 { + interrupts = <43>; + dmacap,memcpy; + dmacap,xor; + }; + }; + + mdio: mdio-bus@72004 { + compatible = "marvell,orion-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72004 0x84>; + interrupts = <30>; + clocks = <&gate_clk 2>; + status = "disabled"; + + ethphy: ethernet-phy { + device-type = "ethernet-phy"; + /* set phy address in board file */ + }; + }; + + eth: ethernet-ctrl@72000 { + compatible = "marvell,orion-eth"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72000 0x4000>; + clocks = <&gate_clk 2>; + marvell,tx-checksum-limit = <1600>; + status = "disabled"; + + ethernet-port@0 { + device_type = "network"; + compatible = "marvell,orion-eth-port"; + reg = <0>; + interrupts = <29>; + /* overwrite MAC address in bootloader */ + local-mac-address = [00 00 00 00 00 00]; + phy-handle = <ðphy>; + }; + }; + + audio0: audio-controller@b0000 { + compatible = "marvell,dove-audio"; + reg = <0xb0000 0x2210>; + interrupts = <19>, <20>; + clocks = <&gate_clk 12>; + clock-names = "internal"; + status = "disabled"; + }; + + audio1: audio-controller@b4000 { + compatible = "marvell,dove-audio"; + reg = <0xb4000 0x2210>; + interrupts = <21>, <22>; + clocks = <&gate_clk 13>; + clock-names = "internal"; + status = "disabled"; }; }; }; diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts new file mode 100644 index 0000000..5babba0 --- /dev/null +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -0,0 +1,275 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "dra7.dtsi" + +/ { + model = "TI DRA7"; + compatible = "ti,dra7-evm", "ti,dra752", "ti,dra7"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x60000000>; /* 1536 MB */ + }; + + mmc2_3v3: fixedregulator-mmc2 { + compatible = "regulator-fixed"; + regulator-name = "mmc2_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&dra7_pmx_core { + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */ + 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x408 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */ + 0x40c (PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + 0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */ + 0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */ + >; + }; + + mcspi1_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + 0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */ + 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */ + 0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */ + 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */ + 0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */ + 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */ + 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */ + >; + }; + + mcspi2_pins: pinmux_mcspi2_pins { + pinctrl-single,pins = < + 0x3c0 (PIN_INPUT | MUX_MODE0) /* spi2_sclk */ + 0x3c4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */ + 0x3c8 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */ + 0x3cc (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x3e0 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */ + 0x3e4 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */ + 0x3e8 (PIN_INPUT | MUX_MODE3) /* uart1_ctsn */ + 0x3ec (PIN_INPUT | MUX_MODE3) /* uart1_rtsn */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0x3f0 (PIN_INPUT | MUX_MODE0) /* uart2_rxd */ + 0x3f4 (PIN_INPUT | MUX_MODE0) /* uart2_txd */ + 0x3f8 (PIN_INPUT | MUX_MODE0) /* uart2_ctsn */ + 0x3fc (PIN_INPUT | MUX_MODE0) /* uart2_rtsn */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */ + 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ + >; + }; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <400000>; + + tps659038: tps659038@58 { + compatible = "ti,tps659038"; + reg = <0x58>; + + tps659038_pmic { + compatible = "ti,tps659038-pmic"; + + regulators { + smps123_reg: smps123 { + /* VDD_MPU */ + regulator-name = "smps123"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + smps45_reg: smps45 { + /* VDD_DSPEVE */ + regulator-name = "smps45"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + }; + + smps6_reg: smps6 { + /* VDD_GPU - over VDD_SMPS6 */ + regulator-name = "smps6"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <12500000>; + regulator-boot-on; + }; + + smps7_reg: smps7 { + /* CORE_VDD */ + regulator-name = "smps7"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1030000>; + regulator-always-on; + regulator-boot-on; + }; + + smps8_reg: smps8 { + /* VDD_IVAHD */ + regulator-name = "smps8"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-boot-on; + }; + + smps9_reg: smps9 { + /* VDDS1V8 */ + regulator-name = "smps9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1_reg: ldo1 { + /* LDO1_OUT --> SDIO */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo2_reg: ldo2 { + /* VDD_RTCIO */ + /* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */ + regulator-name = "ldo2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo3_reg: ldo3 { + /* VDDA_1V8_PHY */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + ldo9_reg: ldo9 { + /* VDD_RTC */ + regulator-name = "ldo9"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-boot-on; + }; + + ldoln_reg: ldoln { + /* VDDA_1V8_PLL */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + }; + }; + }; +}; + +&i2c2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + clock-frequency = <400000>; +}; + +&i2c3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + clock-frequency = <3400000>; +}; + +&mcspi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcspi1_pins>; +}; + +&mcspi2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcspi2_pins>; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&uart3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&ldo1_reg>; + bus-width = <4>; +}; + +&mmc2 { + status = "okay"; + vmmc-supply = <&mmc2_3v3>; + bus-width = <8>; +}; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi new file mode 100644 index 0000000..d0df4c4 --- /dev/null +++ b/arch/arm/boot/dts/dra7.dtsi @@ -0,0 +1,586 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * Based on "omap4.dtsi" + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/dra.h> + +#include "skeleton.dtsi" + +/ { + #address-cells = <1>; + #size-cells = <1>; + + compatible = "ti,dra7xx"; + interrupt-parent = <&gic>; + + aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; + i2c4 = &i2c5; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + serial5 = &uart6; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0>; + + operating-points = < + /* kHz uV */ + 1000000 1060000 + 1176000 1160000 + >; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <1>; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>; + }; + + gic: interrupt-controller@48211000 { + compatible = "arm,cortex-a15-gic"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x48211000 0x1000>, + <0x48212000 0x1000>, + <0x48214000 0x2000>, + <0x48216000 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + /* + * The soc node represents the soc top level view. It is uses for IPs + * that are not memory mapped in the MPU view or for the MPU itself. + */ + soc { + compatible = "ti,omap-infra"; + mpu { + compatible = "ti,omap5-mpu"; + ti,hwmods = "mpu"; + }; + }; + + /* + * XXX: Use a flat representation of the SOC interconnect. + * The real OMAP interconnect network is quite complex. + * Since that will not bring real advantage to represent that in DT for + * the moment, just use a fake OCP bus entry to represent the whole bus + * hierarchy. + */ + ocp { + compatible = "ti,omap4-l3-noc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "l3_main_1", "l3_main_2"; + reg = <0x44000000 0x2000>, + <0x44800000 0x3000>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + + counter32k: counter@4ae04000 { + compatible = "ti,omap-counter32k"; + reg = <0x4ae04000 0x40>; + ti,hwmods = "counter_32k"; + }; + + dra7_pmx_core: pinmux@4a003400 { + compatible = "pinctrl-single"; + reg = <0x4a003400 0x0464>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x3fffffff>; + }; + + sdma: dma-controller@4a056000 { + compatible = "ti,omap4430-sdma"; + reg = <0x4a056000 0x1000>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + #dma-channels = <32>; + #dma-requests = <127>; + }; + + gpio1: gpio@4ae10000 { + compatible = "ti,omap4-gpio"; + reg = <0x4ae10000 0x200>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio1"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio2: gpio@48055000 { + compatible = "ti,omap4-gpio"; + reg = <0x48055000 0x200>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio2"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio3: gpio@48057000 { + compatible = "ti,omap4-gpio"; + reg = <0x48057000 0x200>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio3"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio4: gpio@48059000 { + compatible = "ti,omap4-gpio"; + reg = <0x48059000 0x200>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio4"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio5: gpio@4805b000 { + compatible = "ti,omap4-gpio"; + reg = <0x4805b000 0x200>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio5"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio6: gpio@4805d000 { + compatible = "ti,omap4-gpio"; + reg = <0x4805d000 0x200>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio6"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio7: gpio@48051000 { + compatible = "ti,omap4-gpio"; + reg = <0x48051000 0x200>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio7"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio8: gpio@48053000 { + compatible = "ti,omap4-gpio"; + reg = <0x48053000 0x200>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "gpio8"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + uart1: serial@4806a000 { + compatible = "ti,omap4-uart"; + reg = <0x4806a000 0x100>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart1"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart2: serial@4806c000 { + compatible = "ti,omap4-uart"; + reg = <0x4806c000 0x100>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart2"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart3: serial@48020000 { + compatible = "ti,omap4-uart"; + reg = <0x48020000 0x100>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart3"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart4: serial@4806e000 { + compatible = "ti,omap4-uart"; + reg = <0x4806e000 0x100>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart5: serial@48066000 { + compatible = "ti,omap4-uart"; + reg = <0x48066000 0x100>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart5"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart6: serial@48068000 { + compatible = "ti,omap4-uart"; + reg = <0x48068000 0x100>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "uart6"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart7: serial@48420000 { + compatible = "ti,omap4-uart"; + reg = <0x48420000 0x100>; + ti,hwmods = "uart7"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart8: serial@48422000 { + compatible = "ti,omap4-uart"; + reg = <0x48422000 0x100>; + ti,hwmods = "uart8"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart9: serial@48424000 { + compatible = "ti,omap4-uart"; + reg = <0x48424000 0x100>; + ti,hwmods = "uart9"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + uart10: serial@4ae2b000 { + compatible = "ti,omap4-uart"; + reg = <0x4ae2b000 0x100>; + ti,hwmods = "uart10"; + clock-frequency = <48000000>; + status = "disabled"; + }; + + timer1: timer@4ae18000 { + compatible = "ti,omap5430-timer"; + reg = <0x4ae18000 0x80>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer1"; + ti,timer-alwon; + }; + + timer2: timer@48032000 { + compatible = "ti,omap5430-timer"; + reg = <0x48032000 0x80>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer2"; + }; + + timer3: timer@48034000 { + compatible = "ti,omap5430-timer"; + reg = <0x48034000 0x80>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer3"; + }; + + timer4: timer@48036000 { + compatible = "ti,omap5430-timer"; + reg = <0x48036000 0x80>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer4"; + }; + + timer5: timer@48820000 { + compatible = "ti,omap5430-timer"; + reg = <0x48820000 0x80>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer5"; + ti,timer-dsp; + }; + + timer6: timer@48822000 { + compatible = "ti,omap5430-timer"; + reg = <0x48822000 0x80>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer6"; + ti,timer-dsp; + ti,timer-pwm; + }; + + timer7: timer@48824000 { + compatible = "ti,omap5430-timer"; + reg = <0x48824000 0x80>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer7"; + ti,timer-dsp; + }; + + timer8: timer@48826000 { + compatible = "ti,omap5430-timer"; + reg = <0x48826000 0x80>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer8"; + ti,timer-dsp; + ti,timer-pwm; + }; + + timer9: timer@4803e000 { + compatible = "ti,omap5430-timer"; + reg = <0x4803e000 0x80>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer9"; + }; + + timer10: timer@48086000 { + compatible = "ti,omap5430-timer"; + reg = <0x48086000 0x80>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer10"; + }; + + timer11: timer@48088000 { + compatible = "ti,omap5430-timer"; + reg = <0x48088000 0x80>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "timer11"; + ti,timer-pwm; + }; + + timer13: timer@48828000 { + compatible = "ti,omap5430-timer"; + reg = <0x48828000 0x80>; + ti,hwmods = "timer13"; + status = "disabled"; + }; + + timer14: timer@4882a000 { + compatible = "ti,omap5430-timer"; + reg = <0x4882a000 0x80>; + ti,hwmods = "timer14"; + status = "disabled"; + }; + + timer15: timer@4882c000 { + compatible = "ti,omap5430-timer"; + reg = <0x4882c000 0x80>; + ti,hwmods = "timer15"; + status = "disabled"; + }; + + timer16: timer@4882e000 { + compatible = "ti,omap5430-timer"; + reg = <0x4882e000 0x80>; + ti,hwmods = "timer16"; + status = "disabled"; + }; + + wdt2: wdt@4ae14000 { + compatible = "ti,omap4-wdt"; + reg = <0x4ae14000 0x80>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "wd_timer2"; + }; + + i2c1: i2c@48070000 { + compatible = "ti,omap4-i2c"; + reg = <0x48070000 0x100>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + status = "disabled"; + }; + + i2c2: i2c@48072000 { + compatible = "ti,omap4-i2c"; + reg = <0x48072000 0x100>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c2"; + status = "disabled"; + }; + + i2c3: i2c@48060000 { + compatible = "ti,omap4-i2c"; + reg = <0x48060000 0x100>; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c3"; + status = "disabled"; + }; + + i2c4: i2c@4807a000 { + compatible = "ti,omap4-i2c"; + reg = <0x4807a000 0x100>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c4"; + status = "disabled"; + }; + + i2c5: i2c@4807c000 { + compatible = "ti,omap4-i2c"; + reg = <0x4807c000 0x100>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c5"; + status = "disabled"; + }; + + mmc1: mmc@4809c000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x4809c000 0x400>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + dmas = <&sdma 61>, <&sdma 62>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + mmc2: mmc@480b4000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x480b4000 0x400>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + dmas = <&sdma 47>, <&sdma 48>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + mmc3: mmc@480ad000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x480ad000 0x400>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + dmas = <&sdma 77>, <&sdma 78>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + mmc4: mmc@480d1000 { + compatible = "ti,omap4-hsmmc"; + reg = <0x480d1000 0x400>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmc4"; + ti,needs-special-reset; + dmas = <&sdma 57>, <&sdma 58>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + mcspi1: spi@48098000 { + compatible = "ti,omap4-mcspi"; + reg = <0x48098000 0x200>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; + dmas = <&sdma 35>, + <&sdma 36>, + <&sdma 37>, + <&sdma 38>, + <&sdma 39>, + <&sdma 40>, + <&sdma 41>, + <&sdma 42>; + dma-names = "tx0", "rx0", "tx1", "rx1", + "tx2", "rx2", "tx3", "rx3"; + status = "disabled"; + }; + + mcspi2: spi@4809a000 { + compatible = "ti,omap4-mcspi"; + reg = <0x4809a000 0x200>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi2"; + ti,spi-num-cs = <2>; + dmas = <&sdma 43>, + <&sdma 44>, + <&sdma 45>, + <&sdma 46>; + dma-names = "tx0", "rx0", "tx1", "rx1"; + status = "disabled"; + }; + + mcspi3: spi@480b8000 { + compatible = "ti,omap4-mcspi"; + reg = <0x480b8000 0x200>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi3"; + ti,spi-num-cs = <2>; + dmas = <&sdma 15>, <&sdma 16>; + dma-names = "tx0", "rx0"; + status = "disabled"; + }; + + mcspi4: spi@480ba000 { + compatible = "ti,omap4-mcspi"; + reg = <0x480ba000 0x200>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi4"; + ti,spi-num-cs = <1>; + dmas = <&sdma 70>, <&sdma 71>; + dma-names = "tx0", "rx0"; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index caadc02..a73eeb5 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -49,6 +49,12 @@ reg = <0x10000000 0x100>; }; + mipi_phy: video-phy@10020710 { + compatible = "samsung,s5pv210-mipi-video-phy"; + reg = <0x10020710 8>; + #phy-cells = <1>; + }; + pd_mfc: mfc-power-domain@10023C40 { compatible = "samsung,exynos4210-pd"; reg = <0x10023C40 0x20>; @@ -161,6 +167,8 @@ clock-names = "csis", "sclk_csis"; bus-width = <4>; samsung,power-domain = <&pd_cam>; + phys = <&mipi_phy 0>; + phy-names = "csis"; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -174,6 +182,8 @@ clock-names = "csis", "sclk_csis"; bus-width = <2>; samsung,power-domain = <&pd_cam>; + phys = <&mipi_phy 2>; + phy-names = "csis"; status = "disabled"; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts index 46378fe..1a12fb2 100644 --- a/arch/arm/boot/dts/exynos4210-origen.dts +++ b/arch/arm/boot/dts/exynos4210-origen.dts @@ -32,13 +32,20 @@ bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc"; }; - mmc_reg: voltage-regulator { - compatible = "regulator-fixed"; - regulator-name = "VMEM_VDD_2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - gpio = <&gpx1 1 0>; - enable-active-high; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + mmc_reg: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpx1 1 0>; + enable-active-high; + }; }; tmu@100C0000 { diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts index 8768b03..d65984c 100644 --- a/arch/arm/boot/dts/exynos4412-origen.dts +++ b/arch/arm/boot/dts/exynos4412-origen.dts @@ -32,13 +32,20 @@ reg = <0x0203F000 0x1000>; }; - mmc_reg: voltage-regulator { - compatible = "regulator-fixed"; - regulator-name = "VMEM_VDD_2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - gpio = <&gpx1 1 0>; - enable-active-high; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + mmc_reg: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpx1 1 0>; + enable-active-high; + }; }; pinctrl@11000000 { diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts index cee55fa..6845270 100644 --- a/arch/arm/boot/dts/exynos5250-arndale.dts +++ b/arch/arm/boot/dts/exynos5250-arndale.dts @@ -324,7 +324,14 @@ }; i2c@12C80000 { - status = "disabled"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + samsung,i2c-slave-addr = <0x50>; + + hdmiddc@50 { + compatible = "samsung,exynos4210-hdmiddc"; + reg = <0x50>; + }; }; i2c@12C90000 { @@ -362,6 +369,17 @@ status = "disabled"; }; + i2c@12CE0000 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + samsung,i2c-slave-addr = <0x38>; + + hdmiphy@38 { + compatible = "samsung,exynos4212-hdmiphy"; + reg = <0x38>; + }; + }; + i2c@121D0000 { status = "disabled"; }; @@ -412,6 +430,10 @@ status = "disabled"; }; + i2s0: i2s@03830000 { + status = "okay"; + }; + spi_0: spi@12d20000 { status = "disabled"; }; @@ -482,13 +504,15 @@ #address-cells = <1>; #size-cells = <0>; - main_dc_reg: fixedregulator@1 { + main_dc_reg: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "MAIN_DC"; }; - mmc_reg: voltage-regulator { + mmc_reg: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "VDD_33ON_2.8V"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; @@ -496,8 +520,9 @@ enable-active-high; }; - reg_hdmi_en: fixedregulator@0 { + reg_hdmi_en: regulator@2 { compatible = "regulator-fixed"; + reg = <2>; regulator-name = "hdmi-en"; }; }; diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts index 2538b32..f86d567 100644 --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts @@ -231,14 +231,6 @@ status = "okay"; }; - i2s1: i2s@12D60000 { - status = "disabled"; - }; - - i2s2: i2s@12D70000 { - status = "disabled"; - }; - sound { compatible = "samsung,smdk-wm8994"; diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index bbac42a..9db5047 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -422,6 +422,7 @@ i2s0: i2s@03830000 { compatible = "samsung,s5pv210-i2s"; + status = "disabled"; reg = <0x03830000 0x100>; dmas = <&pdma0 10 &pdma0 9 @@ -438,6 +439,7 @@ i2s1: i2s@12D60000 { compatible = "samsung,s3c6410-i2s"; + status = "disabled"; reg = <0x12D60000 0x100>; dmas = <&pdma1 12 &pdma1 11>; @@ -450,6 +452,7 @@ i2s2: i2s@12D70000 { compatible = "samsung,s3c6410-i2s"; + status = "disabled"; reg = <0x12D70000 0x100>; dmas = <&pdma0 12 &pdma0 11>; @@ -615,16 +618,18 @@ compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x70000>; interrupts = <0 95 0>; - clocks = <&clock 333>, <&clock 136>, <&clock 137>, - <&clock 333>, <&clock 333>; + clocks = <&clock 344>, <&clock 136>, <&clock 137>, + <&clock 159>, <&clock 1024>; clock-names = "hdmi", "sclk_hdmi", "sclk_pixel", - "sclk_hdmiphy", "hdmiphy"; + "sclk_hdmiphy", "mout_hdmi"; }; mixer { compatible = "samsung,exynos5250-mixer"; reg = <0x14450000 0x10000>; interrupts = <0 94 0>; + clocks = <&clock 343>, <&clock 136>; + clock-names = "mixer", "sclk_hdmi"; }; dp_phy: video-phy@10040720 { diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts index bafba25..79524c7 100644 --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts @@ -61,4 +61,30 @@ }; }; + pinctrl@13400000 { + hdmi_hpd_irq: hdmi-hpd-irq { + samsung,pins = "gpx3-7"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; + }; + + hdmi@14530000 { + status = "okay"; + hpd-gpio = <&gpx3 7 0>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_hpd_irq>; + }; + + i2c_2: i2c@12C80000 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + status = "okay"; + + hdmiddc@50 { + compatible = "samsung,exynos4210-hdmiddc"; + reg = <0x50>; + }; + }; }; diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index d537cd7..09aa06c 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -27,6 +27,10 @@ pinctrl2 = &pinctrl_2; pinctrl3 = &pinctrl_3; pinctrl4 = &pinctrl_4; + i2c0 = &i2c_0; + i2c1 = &i2c_1; + i2c2 = &i2c_2; + i2c3 = &i2c_3; }; cpus { @@ -235,4 +239,75 @@ io-channel-ranges; status = "disabled"; }; + + i2c_0: i2c@12C60000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C60000 0x100>; + interrupts = <0 56 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock 261>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_bus>; + status = "disabled"; + }; + + i2c_1: i2c@12C70000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C70000 0x100>; + interrupts = <0 57 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock 262>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_bus>; + status = "disabled"; + }; + + i2c_2: i2c@12C80000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C80000 0x100>; + interrupts = <0 58 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock 263>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_bus>; + status = "disabled"; + }; + + i2c_3: i2c@12C90000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C90000 0x100>; + interrupts = <0 59 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock 264>; + clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_bus>; + status = "disabled"; + }; + + hdmi@14530000 { + compatible = "samsung,exynos4212-hdmi"; + reg = <0x14530000 0x70000>; + interrupts = <0 95 0>; + clocks = <&clock 413>, <&clock 143>, <&clock 768>, + <&clock 158>, <&clock 640>; + clock-names = "hdmi", "sclk_hdmi", "sclk_pixel", + "sclk_hdmiphy", "mout_hdmi"; + status = "disabled"; + }; + + mixer@14450000 { + compatible = "samsung,exynos5420-mixer"; + reg = <0x14450000 0x10000>; + interrupts = <0 94 0>; + clocks = <&clock 431>, <&clock 143>; + clock-names = "mixer", "sclk_hdmi"; + }; }; diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts index a7cb848..d58cb78 100644 --- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts +++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts @@ -68,9 +68,11 @@ pcie@290000 { reset-gpio = <&pin_ctrl 5 0>; + status = "okay"; }; pcie@2a0000 { reset-gpio = <&pin_ctrl 22 0>; + status = "okay"; }; }; diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi index 5d6cf49..8da1070 100644 --- a/arch/arm/boot/dts/exynos5440.dtsi +++ b/arch/arm/boot/dts/exynos5440.dtsi @@ -276,6 +276,7 @@ interrupt-map-mask = <0 0 0 0>; interrupt-map = <0x0 0 &gic 53>; num-lanes = <4>; + status = "disabled"; }; pcie@2a0000 { @@ -296,5 +297,6 @@ interrupt-map-mask = <0 0 0 0>; interrupt-map = <0x0 0 &gic 56>; num-lanes = <4>; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts index 185c7c01..1f026ad 100644 --- a/arch/arm/boot/dts/imx23-evk.dts +++ b/arch/arm/boot/dts/imx23-evk.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx23.dtsi" +#include "imx23.dtsi" / { model = "Freescale i.MX23 Evaluation Kit"; @@ -45,14 +45,14 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */ - 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */ - 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */ - 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ + MX23_PAD_LCD_RESET__GPIO_1_18 + MX23_PAD_PWM3__GPIO_1_29 + MX23_PAD_PWM4__GPIO_1_30 + MX23_PAD_SSP1_DETECT__SSP1_DETECT >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts index fc766ae..526bfdb 100644 --- a/arch/arm/boot/dts/imx23-olinuxino.dts +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -12,7 +12,7 @@ */ /dts-v1/; -/include/ "imx23.dtsi" +#include "imx23.dtsi" / { model = "i.MX23 Olinuxino Low Cost Board"; @@ -40,21 +40,21 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */ + MX23_PAD_GPMI_ALE__GPIO_0_17 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; led_pin_gpio2_1: led_gpio2_1@0 { reg = <0>; fsl,pinmux-ids = < - 0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */ + MX23_PAD_SSP1_DETECT__GPIO_2_1 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx23-pinfunc.h b/arch/arm/boot/dts/imx23-pinfunc.h new file mode 100644 index 0000000..5c0f32ca --- /dev/null +++ b/arch/arm/boot/dts/imx23-pinfunc.h @@ -0,0 +1,333 @@ +/* + * Header providing constants for i.MX23 pinctrl bindings. + * + * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DT_BINDINGS_MX23_PINCTRL_H__ +#define __DT_BINDINGS_MX23_PINCTRL_H__ + +#include "mxs-pinfunc.h" + +#define MX23_PAD_GPMI_D00__GPMI_D00 0x0000 +#define MX23_PAD_GPMI_D01__GPMI_D01 0x0010 +#define MX23_PAD_GPMI_D02__GPMI_D02 0x0020 +#define MX23_PAD_GPMI_D03__GPMI_D03 0x0030 +#define MX23_PAD_GPMI_D04__GPMI_D04 0x0040 +#define MX23_PAD_GPMI_D05__GPMI_D05 0x0050 +#define MX23_PAD_GPMI_D06__GPMI_D06 0x0060 +#define MX23_PAD_GPMI_D07__GPMI_D07 0x0070 +#define MX23_PAD_GPMI_D08__GPMI_D08 0x0080 +#define MX23_PAD_GPMI_D09__GPMI_D09 0x0090 +#define MX23_PAD_GPMI_D10__GPMI_D10 0x00a0 +#define MX23_PAD_GPMI_D11__GPMI_D11 0x00b0 +#define MX23_PAD_GPMI_D12__GPMI_D12 0x00c0 +#define MX23_PAD_GPMI_D13__GPMI_D13 0x00d0 +#define MX23_PAD_GPMI_D14__GPMI_D14 0x00e0 +#define MX23_PAD_GPMI_D15__GPMI_D15 0x00f0 +#define MX23_PAD_GPMI_CLE__GPMI_CLE 0x0100 +#define MX23_PAD_GPMI_ALE__GPMI_ALE 0x0110 +#define MX23_PAD_GPMI_CE2N__GPMI_CE2N 0x0120 +#define MX23_PAD_GPMI_RDY0__GPMI_RDY0 0x0130 +#define MX23_PAD_GPMI_RDY1__GPMI_RDY1 0x0140 +#define MX23_PAD_GPMI_RDY2__GPMI_RDY2 0x0150 +#define MX23_PAD_GPMI_RDY3__GPMI_RDY3 0x0160 +#define MX23_PAD_GPMI_WPN__GPMI_WPN 0x0170 +#define MX23_PAD_GPMI_WRN__GPMI_WRN 0x0180 +#define MX23_PAD_GPMI_RDN__GPMI_RDN 0x0190 +#define MX23_PAD_AUART1_CTS__AUART1_CTS 0x01a0 +#define MX23_PAD_AUART1_RTS__AUART1_RTS 0x01b0 +#define MX23_PAD_AUART1_RX__AUART1_RX 0x01c0 +#define MX23_PAD_AUART1_TX__AUART1_TX 0x01d0 +#define MX23_PAD_I2C_SCL__I2C_SCL 0x01e0 +#define MX23_PAD_I2C_SDA__I2C_SDA 0x01f0 +#define MX23_PAD_LCD_D00__LCD_D00 0x1000 +#define MX23_PAD_LCD_D01__LCD_D01 0x1010 +#define MX23_PAD_LCD_D02__LCD_D02 0x1020 +#define MX23_PAD_LCD_D03__LCD_D03 0x1030 +#define MX23_PAD_LCD_D04__LCD_D04 0x1040 +#define MX23_PAD_LCD_D05__LCD_D05 0x1050 +#define MX23_PAD_LCD_D06__LCD_D06 0x1060 +#define MX23_PAD_LCD_D07__LCD_D07 0x1070 +#define MX23_PAD_LCD_D08__LCD_D08 0x1080 +#define MX23_PAD_LCD_D09__LCD_D09 0x1090 +#define MX23_PAD_LCD_D10__LCD_D10 0x10a0 +#define MX23_PAD_LCD_D11__LCD_D11 0x10b0 +#define MX23_PAD_LCD_D12__LCD_D12 0x10c0 +#define MX23_PAD_LCD_D13__LCD_D13 0x10d0 +#define MX23_PAD_LCD_D14__LCD_D14 0x10e0 +#define MX23_PAD_LCD_D15__LCD_D15 0x10f0 +#define MX23_PAD_LCD_D16__LCD_D16 0x1100 +#define MX23_PAD_LCD_D17__LCD_D17 0x1110 +#define MX23_PAD_LCD_RESET__LCD_RESET 0x1120 +#define MX23_PAD_LCD_RS__LCD_RS 0x1130 +#define MX23_PAD_LCD_WR__LCD_WR 0x1140 +#define MX23_PAD_LCD_CS__LCD_CS 0x1150 +#define MX23_PAD_LCD_DOTCK__LCD_DOTCK 0x1160 +#define MX23_PAD_LCD_ENABLE__LCD_ENABLE 0x1170 +#define MX23_PAD_LCD_HSYNC__LCD_HSYNC 0x1180 +#define MX23_PAD_LCD_VSYNC__LCD_VSYNC 0x1190 +#define MX23_PAD_PWM0__PWM0 0x11a0 +#define MX23_PAD_PWM1__PWM1 0x11b0 +#define MX23_PAD_PWM2__PWM2 0x11c0 +#define MX23_PAD_PWM3__PWM3 0x11d0 +#define MX23_PAD_PWM4__PWM4 0x11e0 +#define MX23_PAD_SSP1_CMD__SSP1_CMD 0x2000 +#define MX23_PAD_SSP1_DETECT__SSP1_DETECT 0x2010 +#define MX23_PAD_SSP1_DATA0__SSP1_DATA0 0x2020 +#define MX23_PAD_SSP1_DATA1__SSP1_DATA1 0x2030 +#define MX23_PAD_SSP1_DATA2__SSP1_DATA2 0x2040 +#define MX23_PAD_SSP1_DATA3__SSP1_DATA3 0x2050 +#define MX23_PAD_SSP1_SCK__SSP1_SCK 0x2060 +#define MX23_PAD_ROTARYA__ROTARYA 0x2070 +#define MX23_PAD_ROTARYB__ROTARYB 0x2080 +#define MX23_PAD_EMI_A00__EMI_A00 0x2090 +#define MX23_PAD_EMI_A01__EMI_A01 0x20a0 +#define MX23_PAD_EMI_A02__EMI_A02 0x20b0 +#define MX23_PAD_EMI_A03__EMI_A03 0x20c0 +#define MX23_PAD_EMI_A04__EMI_A04 0x20d0 +#define MX23_PAD_EMI_A05__EMI_A05 0x20e0 +#define MX23_PAD_EMI_A06__EMI_A06 0x20f0 +#define MX23_PAD_EMI_A07__EMI_A07 0x2100 +#define MX23_PAD_EMI_A08__EMI_A08 0x2110 +#define MX23_PAD_EMI_A09__EMI_A09 0x2120 +#define MX23_PAD_EMI_A10__EMI_A10 0x2130 +#define MX23_PAD_EMI_A11__EMI_A11 0x2140 +#define MX23_PAD_EMI_A12__EMI_A12 0x2150 +#define MX23_PAD_EMI_BA0__EMI_BA0 0x2160 +#define MX23_PAD_EMI_BA1__EMI_BA1 0x2170 +#define MX23_PAD_EMI_CASN__EMI_CASN 0x2180 +#define MX23_PAD_EMI_CE0N__EMI_CE0N 0x2190 +#define MX23_PAD_EMI_CE1N__EMI_CE1N 0x21a0 +#define MX23_PAD_GPMI_CE1N__GPMI_CE1N 0x21b0 +#define MX23_PAD_GPMI_CE0N__GPMI_CE0N 0x21c0 +#define MX23_PAD_EMI_CKE__EMI_CKE 0x21d0 +#define MX23_PAD_EMI_RASN__EMI_RASN 0x21e0 +#define MX23_PAD_EMI_WEN__EMI_WEN 0x21f0 +#define MX23_PAD_EMI_D00__EMI_D00 0x3000 +#define MX23_PAD_EMI_D01__EMI_D01 0x3010 +#define MX23_PAD_EMI_D02__EMI_D02 0x3020 +#define MX23_PAD_EMI_D03__EMI_D03 0x3030 +#define MX23_PAD_EMI_D04__EMI_D04 0x3040 +#define MX23_PAD_EMI_D05__EMI_D05 0x3050 +#define MX23_PAD_EMI_D06__EMI_D06 0x3060 +#define MX23_PAD_EMI_D07__EMI_D07 0x3070 +#define MX23_PAD_EMI_D08__EMI_D08 0x3080 +#define MX23_PAD_EMI_D09__EMI_D09 0x3090 +#define MX23_PAD_EMI_D10__EMI_D10 0x30a0 +#define MX23_PAD_EMI_D11__EMI_D11 0x30b0 +#define MX23_PAD_EMI_D12__EMI_D12 0x30c0 +#define MX23_PAD_EMI_D13__EMI_D13 0x30d0 +#define MX23_PAD_EMI_D14__EMI_D14 0x30e0 +#define MX23_PAD_EMI_D15__EMI_D15 0x30f0 +#define MX23_PAD_EMI_DQM0__EMI_DQM0 0x3100 +#define MX23_PAD_EMI_DQM1__EMI_DQM1 0x3110 +#define MX23_PAD_EMI_DQS0__EMI_DQS0 0x3120 +#define MX23_PAD_EMI_DQS1__EMI_DQS1 0x3130 +#define MX23_PAD_EMI_CLK__EMI_CLK 0x3140 +#define MX23_PAD_EMI_CLKN__EMI_CLKN 0x3150 +#define MX23_PAD_GPMI_D00__LCD_D8 0x0001 +#define MX23_PAD_GPMI_D01__LCD_D9 0x0011 +#define MX23_PAD_GPMI_D02__LCD_D10 0x0021 +#define MX23_PAD_GPMI_D03__LCD_D11 0x0031 +#define MX23_PAD_GPMI_D04__LCD_D12 0x0041 +#define MX23_PAD_GPMI_D05__LCD_D13 0x0051 +#define MX23_PAD_GPMI_D06__LCD_D14 0x0061 +#define MX23_PAD_GPMI_D07__LCD_D15 0x0071 +#define MX23_PAD_GPMI_D08__LCD_D18 0x0081 +#define MX23_PAD_GPMI_D09__LCD_D19 0x0091 +#define MX23_PAD_GPMI_D10__LCD_D20 0x00a1 +#define MX23_PAD_GPMI_D11__LCD_D21 0x00b1 +#define MX23_PAD_GPMI_D12__LCD_D22 0x00c1 +#define MX23_PAD_GPMI_D13__LCD_D23 0x00d1 +#define MX23_PAD_GPMI_D14__AUART2_RX 0x00e1 +#define MX23_PAD_GPMI_D15__AUART2_TX 0x00f1 +#define MX23_PAD_GPMI_CLE__LCD_D16 0x0101 +#define MX23_PAD_GPMI_ALE__LCD_D17 0x0111 +#define MX23_PAD_GPMI_CE2N__ATA_A2 0x0121 +#define MX23_PAD_AUART1_RTS__IR_CLK 0x01b1 +#define MX23_PAD_AUART1_RX__IR_RX 0x01c1 +#define MX23_PAD_AUART1_TX__IR_TX 0x01d1 +#define MX23_PAD_I2C_SCL__GPMI_RDY2 0x01e1 +#define MX23_PAD_I2C_SDA__GPMI_CE2N 0x01f1 +#define MX23_PAD_LCD_D00__ETM_DA8 0x1001 +#define MX23_PAD_LCD_D01__ETM_DA9 0x1011 +#define MX23_PAD_LCD_D02__ETM_DA10 0x1021 +#define MX23_PAD_LCD_D03__ETM_DA11 0x1031 +#define MX23_PAD_LCD_D04__ETM_DA12 0x1041 +#define MX23_PAD_LCD_D05__ETM_DA13 0x1051 +#define MX23_PAD_LCD_D06__ETM_DA14 0x1061 +#define MX23_PAD_LCD_D07__ETM_DA15 0x1071 +#define MX23_PAD_LCD_D08__ETM_DA0 0x1081 +#define MX23_PAD_LCD_D09__ETM_DA1 0x1091 +#define MX23_PAD_LCD_D10__ETM_DA2 0x10a1 +#define MX23_PAD_LCD_D11__ETM_DA3 0x10b1 +#define MX23_PAD_LCD_D12__ETM_DA4 0x10c1 +#define MX23_PAD_LCD_D13__ETM_DA5 0x10d1 +#define MX23_PAD_LCD_D14__ETM_DA6 0x10e1 +#define MX23_PAD_LCD_D15__ETM_DA7 0x10f1 +#define MX23_PAD_LCD_RESET__ETM_TCTL 0x1121 +#define MX23_PAD_LCD_RS__ETM_TCLK 0x1131 +#define MX23_PAD_LCD_DOTCK__GPMI_RDY3 0x1161 +#define MX23_PAD_LCD_ENABLE__I2C_SCL 0x1171 +#define MX23_PAD_LCD_HSYNC__I2C_SDA 0x1181 +#define MX23_PAD_LCD_VSYNC__LCD_BUSY 0x1191 +#define MX23_PAD_PWM0__ROTARYA 0x11a1 +#define MX23_PAD_PWM1__ROTARYB 0x11b1 +#define MX23_PAD_PWM2__GPMI_RDY3 0x11c1 +#define MX23_PAD_PWM3__ETM_TCTL 0x11d1 +#define MX23_PAD_PWM4__ETM_TCLK 0x11e1 +#define MX23_PAD_SSP1_DETECT__GPMI_CE3N 0x2011 +#define MX23_PAD_SSP1_DATA1__I2C_SCL 0x2031 +#define MX23_PAD_SSP1_DATA2__I2C_SDA 0x2041 +#define MX23_PAD_ROTARYA__AUART2_RTS 0x2071 +#define MX23_PAD_ROTARYB__AUART2_CTS 0x2081 +#define MX23_PAD_GPMI_D00__SSP2_DATA0 0x0002 +#define MX23_PAD_GPMI_D01__SSP2_DATA1 0x0012 +#define MX23_PAD_GPMI_D02__SSP2_DATA2 0x0022 +#define MX23_PAD_GPMI_D03__SSP2_DATA3 0x0032 +#define MX23_PAD_GPMI_D04__SSP2_DATA4 0x0042 +#define MX23_PAD_GPMI_D05__SSP2_DATA5 0x0052 +#define MX23_PAD_GPMI_D06__SSP2_DATA6 0x0062 +#define MX23_PAD_GPMI_D07__SSP2_DATA7 0x0072 +#define MX23_PAD_GPMI_D08__SSP1_DATA4 0x0082 +#define MX23_PAD_GPMI_D09__SSP1_DATA5 0x0092 +#define MX23_PAD_GPMI_D10__SSP1_DATA6 0x00a2 +#define MX23_PAD_GPMI_D11__SSP1_DATA7 0x00b2 +#define MX23_PAD_GPMI_D15__GPMI_CE3N 0x00f2 +#define MX23_PAD_GPMI_RDY0__SSP2_DETECT 0x0132 +#define MX23_PAD_GPMI_RDY1__SSP2_CMD 0x0142 +#define MX23_PAD_GPMI_WRN__SSP2_SCK 0x0182 +#define MX23_PAD_AUART1_CTS__SSP1_DATA4 0x01a2 +#define MX23_PAD_AUART1_RTS__SSP1_DATA5 0x01b2 +#define MX23_PAD_AUART1_RX__SSP1_DATA6 0x01c2 +#define MX23_PAD_AUART1_TX__SSP1_DATA7 0x01d2 +#define MX23_PAD_I2C_SCL__AUART1_TX 0x01e2 +#define MX23_PAD_I2C_SDA__AUART1_RX 0x01f2 +#define MX23_PAD_LCD_D08__SAIF2_SDATA0 0x1082 +#define MX23_PAD_LCD_D09__SAIF1_SDATA0 0x1092 +#define MX23_PAD_LCD_D10__SAIF_MCLK_BITCLK 0x10a2 +#define MX23_PAD_LCD_D11__SAIF_LRCLK 0x10b2 +#define MX23_PAD_LCD_D12__SAIF2_SDATA1 0x10c2 +#define MX23_PAD_LCD_D13__SAIF2_SDATA2 0x10d2 +#define MX23_PAD_LCD_D14__SAIF1_SDATA2 0x10e2 +#define MX23_PAD_LCD_D15__SAIF1_SDATA1 0x10f2 +#define MX23_PAD_LCD_D16__SAIF_ALT_BITCLK 0x1102 +#define MX23_PAD_LCD_RESET__GPMI_CE3N 0x1122 +#define MX23_PAD_PWM0__DUART_RX 0x11a2 +#define MX23_PAD_PWM1__DUART_TX 0x11b2 +#define MX23_PAD_PWM3__AUART1_CTS 0x11d2 +#define MX23_PAD_PWM4__AUART1_RTS 0x11e2 +#define MX23_PAD_SSP1_CMD__JTAG_TDO 0x2002 +#define MX23_PAD_SSP1_DETECT__USB_OTG_ID 0x2012 +#define MX23_PAD_SSP1_DATA0__JTAG_TDI 0x2022 +#define MX23_PAD_SSP1_DATA1__JTAG_TCLK 0x2032 +#define MX23_PAD_SSP1_DATA2__JTAG_RTCK 0x2042 +#define MX23_PAD_SSP1_DATA3__JTAG_TMS 0x2052 +#define MX23_PAD_SSP1_SCK__JTAG_TRST 0x2062 +#define MX23_PAD_ROTARYA__SPDIF 0x2072 +#define MX23_PAD_ROTARYB__GPMI_CE3N 0x2082 +#define MX23_PAD_GPMI_D00__GPIO_0_0 0x0003 +#define MX23_PAD_GPMI_D01__GPIO_0_1 0x0013 +#define MX23_PAD_GPMI_D02__GPIO_0_2 0x0023 +#define MX23_PAD_GPMI_D03__GPIO_0_3 0x0033 +#define MX23_PAD_GPMI_D04__GPIO_0_4 0x0043 +#define MX23_PAD_GPMI_D05__GPIO_0_5 0x0053 +#define MX23_PAD_GPMI_D06__GPIO_0_6 0x0063 +#define MX23_PAD_GPMI_D07__GPIO_0_7 0x0073 +#define MX23_PAD_GPMI_D08__GPIO_0_8 0x0083 +#define MX23_PAD_GPMI_D09__GPIO_0_9 0x0093 +#define MX23_PAD_GPMI_D10__GPIO_0_10 0x00a3 +#define MX23_PAD_GPMI_D11__GPIO_0_11 0x00b3 +#define MX23_PAD_GPMI_D12__GPIO_0_12 0x00c3 +#define MX23_PAD_GPMI_D13__GPIO_0_13 0x00d3 +#define MX23_PAD_GPMI_D14__GPIO_0_14 0x00e3 +#define MX23_PAD_GPMI_D15__GPIO_0_15 0x00f3 +#define MX23_PAD_GPMI_CLE__GPIO_0_16 0x0103 +#define MX23_PAD_GPMI_ALE__GPIO_0_17 0x0113 +#define MX23_PAD_GPMI_CE2N__GPIO_0_18 0x0123 +#define MX23_PAD_GPMI_RDY0__GPIO_0_19 0x0133 +#define MX23_PAD_GPMI_RDY1__GPIO_0_20 0x0143 +#define MX23_PAD_GPMI_RDY2__GPIO_0_21 0x0153 +#define MX23_PAD_GPMI_RDY3__GPIO_0_22 0x0163 +#define MX23_PAD_GPMI_WPN__GPIO_0_23 0x0173 +#define MX23_PAD_GPMI_WRN__GPIO_0_24 0x0183 +#define MX23_PAD_GPMI_RDN__GPIO_0_25 0x0193 +#define MX23_PAD_AUART1_CTS__GPIO_0_26 0x01a3 +#define MX23_PAD_AUART1_RTS__GPIO_0_27 0x01b3 +#define MX23_PAD_AUART1_RX__GPIO_0_28 0x01c3 +#define MX23_PAD_AUART1_TX__GPIO_0_29 0x01d3 +#define MX23_PAD_I2C_SCL__GPIO_0_30 0x01e3 +#define MX23_PAD_I2C_SDA__GPIO_0_31 0x01f3 +#define MX23_PAD_LCD_D00__GPIO_1_0 0x1003 +#define MX23_PAD_LCD_D01__GPIO_1_1 0x1013 +#define MX23_PAD_LCD_D02__GPIO_1_2 0x1023 +#define MX23_PAD_LCD_D03__GPIO_1_3 0x1033 +#define MX23_PAD_LCD_D04__GPIO_1_4 0x1043 +#define MX23_PAD_LCD_D05__GPIO_1_5 0x1053 +#define MX23_PAD_LCD_D06__GPIO_1_6 0x1063 +#define MX23_PAD_LCD_D07__GPIO_1_7 0x1073 +#define MX23_PAD_LCD_D08__GPIO_1_8 0x1083 +#define MX23_PAD_LCD_D09__GPIO_1_9 0x1093 +#define MX23_PAD_LCD_D10__GPIO_1_10 0x10a3 +#define MX23_PAD_LCD_D11__GPIO_1_11 0x10b3 +#define MX23_PAD_LCD_D12__GPIO_1_12 0x10c3 +#define MX23_PAD_LCD_D13__GPIO_1_13 0x10d3 +#define MX23_PAD_LCD_D14__GPIO_1_14 0x10e3 +#define MX23_PAD_LCD_D15__GPIO_1_15 0x10f3 +#define MX23_PAD_LCD_D16__GPIO_1_16 0x1103 +#define MX23_PAD_LCD_D17__GPIO_1_17 0x1113 +#define MX23_PAD_LCD_RESET__GPIO_1_18 0x1123 +#define MX23_PAD_LCD_RS__GPIO_1_19 0x1133 +#define MX23_PAD_LCD_WR__GPIO_1_20 0x1143 +#define MX23_PAD_LCD_CS__GPIO_1_21 0x1153 +#define MX23_PAD_LCD_DOTCK__GPIO_1_22 0x1163 +#define MX23_PAD_LCD_ENABLE__GPIO_1_23 0x1173 +#define MX23_PAD_LCD_HSYNC__GPIO_1_24 0x1183 +#define MX23_PAD_LCD_VSYNC__GPIO_1_25 0x1193 +#define MX23_PAD_PWM0__GPIO_1_26 0x11a3 +#define MX23_PAD_PWM1__GPIO_1_27 0x11b3 +#define MX23_PAD_PWM2__GPIO_1_28 0x11c3 +#define MX23_PAD_PWM3__GPIO_1_29 0x11d3 +#define MX23_PAD_PWM4__GPIO_1_30 0x11e3 +#define MX23_PAD_SSP1_CMD__GPIO_2_0 0x2003 +#define MX23_PAD_SSP1_DETECT__GPIO_2_1 0x2013 +#define MX23_PAD_SSP1_DATA0__GPIO_2_2 0x2023 +#define MX23_PAD_SSP1_DATA1__GPIO_2_3 0x2033 +#define MX23_PAD_SSP1_DATA2__GPIO_2_4 0x2043 +#define MX23_PAD_SSP1_DATA3__GPIO_2_5 0x2053 +#define MX23_PAD_SSP1_SCK__GPIO_2_6 0x2063 +#define MX23_PAD_ROTARYA__GPIO_2_7 0x2073 +#define MX23_PAD_ROTARYB__GPIO_2_8 0x2083 +#define MX23_PAD_EMI_A00__GPIO_2_9 0x2093 +#define MX23_PAD_EMI_A01__GPIO_2_10 0x20a3 +#define MX23_PAD_EMI_A02__GPIO_2_11 0x20b3 +#define MX23_PAD_EMI_A03__GPIO_2_12 0x20c3 +#define MX23_PAD_EMI_A04__GPIO_2_13 0x20d3 +#define MX23_PAD_EMI_A05__GPIO_2_14 0x20e3 +#define MX23_PAD_EMI_A06__GPIO_2_15 0x20f3 +#define MX23_PAD_EMI_A07__GPIO_2_16 0x2103 +#define MX23_PAD_EMI_A08__GPIO_2_17 0x2113 +#define MX23_PAD_EMI_A09__GPIO_2_18 0x2123 +#define MX23_PAD_EMI_A10__GPIO_2_19 0x2133 +#define MX23_PAD_EMI_A11__GPIO_2_20 0x2143 +#define MX23_PAD_EMI_A12__GPIO_2_21 0x2153 +#define MX23_PAD_EMI_BA0__GPIO_2_22 0x2163 +#define MX23_PAD_EMI_BA1__GPIO_2_23 0x2173 +#define MX23_PAD_EMI_CASN__GPIO_2_24 0x2183 +#define MX23_PAD_EMI_CE0N__GPIO_2_25 0x2193 +#define MX23_PAD_EMI_CE1N__GPIO_2_26 0x21a3 +#define MX23_PAD_GPMI_CE1N__GPIO_2_27 0x21b3 +#define MX23_PAD_GPMI_CE0N__GPIO_2_28 0x21c3 +#define MX23_PAD_EMI_CKE__GPIO_2_29 0x21d3 +#define MX23_PAD_EMI_RASN__GPIO_2_30 0x21e3 +#define MX23_PAD_EMI_WEN__GPIO_2_31 0x21f3 + +#endif /* __DT_BINDINGS_MX23_PINCTRL_H__ */ diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts index 85c3864..cb64e2b 100644 --- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts +++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx23.dtsi" +#include "imx23.dtsi" / { model = "Freescale STMP378x Development Board"; @@ -39,12 +39,12 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */ - 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */ + MX23_PAD_PWM3__GPIO_1_29 + MX23_PAD_PWM4__GPIO_1_30 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; }; diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi index 07caf76..c96ceae 100644 --- a/arch/arm/boot/dts/imx23.dtsi +++ b/arch/arm/boot/dts/imx23.dtsi @@ -9,7 +9,8 @@ * http://www.gnu.org/copyleft/gpl.html */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" +#include "imx23-pinfunc.h" / { interrupt-parent = <&icoll>; @@ -137,174 +138,174 @@ duart_pins_a: duart@0 { reg = <0>; fsl,pinmux-ids = < - 0x11a2 /* MX23_PAD_PWM0__DUART_RX */ - 0x11b2 /* MX23_PAD_PWM1__DUART_TX */ + MX23_PAD_PWM0__DUART_RX + MX23_PAD_PWM1__DUART_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart0_pins_a: auart0@0 { reg = <0>; fsl,pinmux-ids = < - 0x01c0 /* MX23_PAD_AUART1_RX__AUART1_RX */ - 0x01d0 /* MX23_PAD_AUART1_TX__AUART1_TX */ - 0x01a0 /* MX23_PAD_AUART1_CTS__AUART1_CTS */ - 0x01b0 /* MX23_PAD_AUART1_RTS__AUART1_RTS */ + MX23_PAD_AUART1_RX__AUART1_RX + MX23_PAD_AUART1_TX__AUART1_TX + MX23_PAD_AUART1_CTS__AUART1_CTS + MX23_PAD_AUART1_RTS__AUART1_RTS >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart0_2pins_a: auart0-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x01e2 /* MX23_PAD_I2C_SCL__AUART1_TX */ - 0x01f2 /* MX23_PAD_I2C_SDA__AUART1_RX */ + MX23_PAD_I2C_SCL__AUART1_TX + MX23_PAD_I2C_SDA__AUART1_RX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; gpmi_pins_a: gpmi-nand@0 { reg = <0>; fsl,pinmux-ids = < - 0x0000 /* MX23_PAD_GPMI_D00__GPMI_D00 */ - 0x0010 /* MX23_PAD_GPMI_D01__GPMI_D01 */ - 0x0020 /* MX23_PAD_GPMI_D02__GPMI_D02 */ - 0x0030 /* MX23_PAD_GPMI_D03__GPMI_D03 */ - 0x0040 /* MX23_PAD_GPMI_D04__GPMI_D04 */ - 0x0050 /* MX23_PAD_GPMI_D05__GPMI_D05 */ - 0x0060 /* MX23_PAD_GPMI_D06__GPMI_D06 */ - 0x0070 /* MX23_PAD_GPMI_D07__GPMI_D07 */ - 0x0100 /* MX23_PAD_GPMI_CLE__GPMI_CLE */ - 0x0110 /* MX23_PAD_GPMI_ALE__GPMI_ALE */ - 0x0130 /* MX23_PAD_GPMI_RDY0__GPMI_RDY0 */ - 0x0140 /* MX23_PAD_GPMI_RDY1__GPMI_RDY1 */ - 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */ - 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */ - 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */ - 0x21b0 /* MX23_PAD_GPMI_CE1N__GPMI_CE1N */ - 0x21c0 /* MX23_PAD_GPMI_CE0N__GPMI_CE0N */ + MX23_PAD_GPMI_D00__GPMI_D00 + MX23_PAD_GPMI_D01__GPMI_D01 + MX23_PAD_GPMI_D02__GPMI_D02 + MX23_PAD_GPMI_D03__GPMI_D03 + MX23_PAD_GPMI_D04__GPMI_D04 + MX23_PAD_GPMI_D05__GPMI_D05 + MX23_PAD_GPMI_D06__GPMI_D06 + MX23_PAD_GPMI_D07__GPMI_D07 + MX23_PAD_GPMI_CLE__GPMI_CLE + MX23_PAD_GPMI_ALE__GPMI_ALE + MX23_PAD_GPMI_RDY0__GPMI_RDY0 + MX23_PAD_GPMI_RDY1__GPMI_RDY1 + MX23_PAD_GPMI_WPN__GPMI_WPN + MX23_PAD_GPMI_WRN__GPMI_WRN + MX23_PAD_GPMI_RDN__GPMI_RDN + MX23_PAD_GPMI_CE1N__GPMI_CE1N + MX23_PAD_GPMI_CE0N__GPMI_CE0N >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; gpmi_pins_fixup: gpmi-pins-fixup { fsl,pinmux-ids = < - 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */ - 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */ - 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */ + MX23_PAD_GPMI_WPN__GPMI_WPN + MX23_PAD_GPMI_WRN__GPMI_WRN + MX23_PAD_GPMI_RDN__GPMI_RDN >; - fsl,drive-strength = <2>; + fsl,drive-strength = <MXS_DRIVE_12mA>; }; mmc0_4bit_pins_a: mmc0-4bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */ - 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */ - 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */ - 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */ - 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */ - 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + MX23_PAD_SSP1_DATA0__SSP1_DATA0 + MX23_PAD_SSP1_DATA1__SSP1_DATA1 + MX23_PAD_SSP1_DATA2__SSP1_DATA2 + MX23_PAD_SSP1_DATA3__SSP1_DATA3 + MX23_PAD_SSP1_CMD__SSP1_CMD + MX23_PAD_SSP1_SCK__SSP1_SCK >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mmc0_8bit_pins_a: mmc0-8bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */ - 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */ - 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */ - 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */ - 0x0082 /* MX23_PAD_GPMI_D08__SSP1_DATA4 */ - 0x0092 /* MX23_PAD_GPMI_D09__SSP1_DATA5 */ - 0x00a2 /* MX23_PAD_GPMI_D10__SSP1_DATA6 */ - 0x00b2 /* MX23_PAD_GPMI_D11__SSP1_DATA7 */ - 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */ - 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ - 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + MX23_PAD_SSP1_DATA0__SSP1_DATA0 + MX23_PAD_SSP1_DATA1__SSP1_DATA1 + MX23_PAD_SSP1_DATA2__SSP1_DATA2 + MX23_PAD_SSP1_DATA3__SSP1_DATA3 + MX23_PAD_GPMI_D08__SSP1_DATA4 + MX23_PAD_GPMI_D09__SSP1_DATA5 + MX23_PAD_GPMI_D10__SSP1_DATA6 + MX23_PAD_GPMI_D11__SSP1_DATA7 + MX23_PAD_SSP1_CMD__SSP1_CMD + MX23_PAD_SSP1_DETECT__SSP1_DETECT + MX23_PAD_SSP1_SCK__SSP1_SCK >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mmc0_pins_fixup: mmc0-pins-fixup { fsl,pinmux-ids = < - 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ - 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + MX23_PAD_SSP1_DETECT__SSP1_DETECT + MX23_PAD_SSP1_SCK__SSP1_SCK >; - fsl,pull-up = <0>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; pwm2_pins_a: pwm2@0 { reg = <0>; fsl,pinmux-ids = < - 0x11c0 /* MX23_PAD_PWM2__PWM2 */ + MX23_PAD_PWM2__PWM2 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_24bit_pins_a: lcdif-24bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX23_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX23_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX23_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX23_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX23_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX23_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX23_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX23_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX23_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX23_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX23_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX23_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX23_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX23_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX23_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX23_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX23_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX23_PAD_LCD_D17__LCD_D17 */ - 0x0081 /* MX23_PAD_GPMI_D08__LCD_D18 */ - 0x0091 /* MX23_PAD_GPMI_D09__LCD_D19 */ - 0x00a1 /* MX23_PAD_GPMI_D10__LCD_D20 */ - 0x00b1 /* MX23_PAD_GPMI_D11__LCD_D21 */ - 0x00c1 /* MX23_PAD_GPMI_D12__LCD_D22 */ - 0x00d1 /* MX23_PAD_GPMI_D13__LCD_D23 */ - 0x1160 /* MX23_PAD_LCD_DOTCK__LCD_DOTCK */ - 0x1170 /* MX23_PAD_LCD_ENABLE__LCD_ENABLE */ - 0x1180 /* MX23_PAD_LCD_HSYNC__LCD_HSYNC */ - 0x1190 /* MX23_PAD_LCD_VSYNC__LCD_VSYNC */ + MX23_PAD_LCD_D00__LCD_D00 + MX23_PAD_LCD_D01__LCD_D01 + MX23_PAD_LCD_D02__LCD_D02 + MX23_PAD_LCD_D03__LCD_D03 + MX23_PAD_LCD_D04__LCD_D04 + MX23_PAD_LCD_D05__LCD_D05 + MX23_PAD_LCD_D06__LCD_D06 + MX23_PAD_LCD_D07__LCD_D07 + MX23_PAD_LCD_D08__LCD_D08 + MX23_PAD_LCD_D09__LCD_D09 + MX23_PAD_LCD_D10__LCD_D10 + MX23_PAD_LCD_D11__LCD_D11 + MX23_PAD_LCD_D12__LCD_D12 + MX23_PAD_LCD_D13__LCD_D13 + MX23_PAD_LCD_D14__LCD_D14 + MX23_PAD_LCD_D15__LCD_D15 + MX23_PAD_LCD_D16__LCD_D16 + MX23_PAD_LCD_D17__LCD_D17 + MX23_PAD_GPMI_D08__LCD_D18 + MX23_PAD_GPMI_D09__LCD_D19 + MX23_PAD_GPMI_D10__LCD_D20 + MX23_PAD_GPMI_D11__LCD_D21 + MX23_PAD_GPMI_D12__LCD_D22 + MX23_PAD_GPMI_D13__LCD_D23 + MX23_PAD_LCD_DOTCK__LCD_DOTCK + MX23_PAD_LCD_ENABLE__LCD_ENABLE + MX23_PAD_LCD_HSYNC__LCD_HSYNC + MX23_PAD_LCD_VSYNC__LCD_VSYNC >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; spi2_pins_a: spi2@0 { reg = <0>; fsl,pinmux-ids = < - 0x0182 /* MX23_PAD_GPMI_WRN__SSP2_SCK */ - 0x0142 /* MX23_PAD_GPMI_RDY1__SSP2_CMD */ - 0x0002 /* MX23_PAD_GPMI_D00__SSP2_DATA0 */ - 0x0032 /* MX23_PAD_GPMI_D03__SSP2_DATA3 */ + MX23_PAD_GPMI_WRN__SSP2_SCK + MX23_PAD_GPMI_RDY1__SSP2_CMD + MX23_PAD_GPMI_D00__SSP2_DATA0 + MX23_PAD_GPMI_D03__SSP2_DATA3 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; }; diff --git a/arch/arm/boot/dts/imx27-apf27dev.dts b/arch/arm/boot/dts/imx27-apf27dev.dts index 2a377ca..47c8c26 100644 --- a/arch/arm/boot/dts/imx27-apf27dev.dts +++ b/arch/arm/boot/dts/imx27-apf27dev.dts @@ -16,6 +16,26 @@ model = "Armadeus Systems APF27Dev docking/development board"; compatible = "armadeus,imx27-apf27dev", "armadeus,imx27-apf27", "fsl,imx27"; + display: display { + model = "Chimei-LW700AT9003"; + native-mode = <&timing0>; + bits-per-pixel = <16>; /* non-standard but required */ + fsl,pcr = <0xfae80083>; /* non-standard but required */ + display-timings { + timing0: 640x480 { + clock-frequency = <33000033>; + hactive = <800>; + vactive = <640>; + hback-porch = <96>; + hfront-porch = <96>; + vback-porch = <20>; + vfront-porch = <21>; + hsync-len = <64>; + vsync-len = <4>; + }; + }; + }; + gpio-keys { compatible = "gpio-keys"; @@ -50,6 +70,12 @@ status = "okay"; }; +&fb { + display = <&display>; + fsl,dmacr = <0x00020010>; + status = "okay"; +}; + &i2c1 { clock-frequency = <400000>; status = "okay"; diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index b7a1c6d..826231e 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -123,6 +123,7 @@ }; pwm: pwm@10006000 { + #pwm-cells = <2>; compatible = "fsl,imx27-pwm"; reg = <0x10006000 0x1000>; interrupts = <23>; diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts index 7eb0758..7198fe3 100644 --- a/arch/arm/boot/dts/imx28-apf28.dts +++ b/arch/arm/boot/dts/imx28-apf28.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Armadeus Systems APF28 module"; diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts index b602494..e2efd8d 100644 --- a/arch/arm/boot/dts/imx28-apf28dev.dts +++ b/arch/arm/boot/dts/imx28-apf28dev.dts @@ -10,7 +10,7 @@ */ /* APF28Dev is a docking board for the APF28 SOM */ -/include/ "imx28-apf28.dts" +#include "imx28-apf28.dts" / { model = "Armadeus Systems APF28Dev docking/development board"; @@ -41,30 +41,30 @@ hog_pins_apf28dev: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x1103 /* MX28_PAD_LCD_D16__GPIO_1_16 */ - 0x1113 /* MX28_PAD_LCD_D17__GPIO_1_17 */ - 0x1123 /* MX28_PAD_LCD_D18__GPIO_1_18 */ - 0x1133 /* MX28_PAD_LCD_D19__GPIO_1_19 */ - 0x1143 /* MX28_PAD_LCD_D20__GPIO_1_20 */ - 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */ - 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */ + MX28_PAD_LCD_D16__GPIO_1_16 + MX28_PAD_LCD_D17__GPIO_1_17 + MX28_PAD_LCD_D18__GPIO_1_18 + MX28_PAD_LCD_D19__GPIO_1_19 + MX28_PAD_LCD_D20__GPIO_1_20 + MX28_PAD_LCD_D21__GPIO_1_21 + MX28_PAD_LCD_D22__GPIO_1_22 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_apf28dev: lcdif-apf28dev@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts index 0e7fed4..6f254ca 100644 --- a/arch/arm/boot/dts/imx28-apx4devkit.dts +++ b/arch/arm/boot/dts/imx28-apx4devkit.dts @@ -1,5 +1,5 @@ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Bluegiga APX4 Development Kit"; @@ -40,53 +40,53 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */ - 0x0153 /* MX28_PAD_GPMI_RDY1__GPIO_0_21 */ - 0x2123 /* MX28_PAD_SSP2_MISO__GPIO_2_18 */ - 0x2131 /* MX28_PAD_SSP2_SS0__GPIO_2_19 */ - 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ - 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 */ + MX28_PAD_GPMI_CE1N__GPIO_0_17 + MX28_PAD_GPMI_RDY1__GPIO_0_21 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */ + MX28_PAD_PWM3__GPIO_3_28 + MX28_PAD_LCD_RESET__GPIO_3_30 + MX28_PAD_JTAG_RTCK__GPIO_4_20 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_apx4: lcdif-apx4@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 { reg = <0>; fsl,pinmux-ids = < - 0x2041 /* MX28_PAD_SSP0_DATA4__SSP2_D0 */ - 0x2051 /* MX28_PAD_SSP0_DATA5__SSP2_D3 */ - 0x2061 /* MX28_PAD_SSP0_DATA6__SSP2_CMD */ - 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */ - 0x2141 /* MX28_PAD_SSP2_SS1__SSP2_D1 */ - 0x2151 /* MX28_PAD_SSP2_SS2__SSP2_D2 */ + MX28_PAD_SSP0_DATA4__SSP2_D0 + MX28_PAD_SSP0_DATA5__SSP2_D3 + MX28_PAD_SSP0_DATA6__SSP2_CMD + MX28_PAD_SSP0_DATA7__SSP2_SCK + MX28_PAD_SSP2_SS1__SSP2_D1 + MX28_PAD_SSP2_SS2__SSP2_D2 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 { fsl,pinmux-ids = < - 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */ + MX28_PAD_SSP0_DATA7__SSP2_SCK >; - fsl,drive-strength = <2>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts index 1ec8c94..cabb617 100644 --- a/arch/arm/boot/dts/imx28-cfa10036.dts +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Crystalfontz CFA-10036 Board"; @@ -26,31 +26,31 @@ ssd1306_cfa10036: ssd1306-10036@0 { reg = <0>; fsl,pinmux-ids = < - 0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */ + MX28_PAD_SSP0_DATA7__GPIO_2_7 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; led_pins_cfa10036: leds-10036@0 { reg = <0>; fsl,pinmux-ids = < - 0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */ + MX28_PAD_AUART1_RX__GPIO_3_4 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; usb0_otg_cfa10036: otg-10036@0 { reg = <0>; fsl,pinmux-ids = < - 0x0142 /* MX28_PAD_GPMI_READY0__USB0_ID */ + MX28_PAD_GPMI_RDY0__USB0_ID >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts index 182b99f..f93e9a7 100644 --- a/arch/arm/boot/dts/imx28-cfa10037.dts +++ b/arch/arm/boot/dts/imx28-cfa10037.dts @@ -13,7 +13,7 @@ * The CFA-10049 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10037 Board"; @@ -25,21 +25,21 @@ usb_pins_cfa10037: usb-10037@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; mac0_pins_cfa10037: mac0-10037@0 { reg = <0>; fsl,pinmux-ids = < - 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */ + MX28_PAD_SSP2_SS2__GPIO_2_21 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts index 06e4cfa..7087b4b 100644 --- a/arch/arm/boot/dts/imx28-cfa10049.dts +++ b/arch/arm/boot/dts/imx28-cfa10049.dts @@ -13,7 +13,7 @@ * The CFA-10049 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10049 Board"; @@ -25,150 +25,150 @@ usb_pins_cfa10049: usb-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; i2cmux_pins_cfa10049: i2cmux-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */ - 0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */ + MX28_PAD_LCD_D22__GPIO_1_22 + MX28_PAD_LCD_D23__GPIO_1_23 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; mac0_pins_cfa10049: mac0-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */ + MX28_PAD_SSP2_SS2__GPIO_2_21 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; pca_pins_cfa10049: pca-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */ + MX28_PAD_SSP2_SS0__GPIO_2_19 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; rotary_pins_cfa10049: rotary-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */ - 0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */ + MX28_PAD_I2C0_SCL__GPIO_3_24 + MX28_PAD_I2C0_SDA__GPIO_3_25 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; rotary_btn_pins_cfa10049: rotary-btn-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */ + MX28_PAD_SAIF1_SDATA0__GPIO_3_26 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; spi2_pins_cfa10049: spi2-cfa10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */ - 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */ - 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */ - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_SSP2_SCK__GPIO_2_16 + MX28_PAD_SSP2_MOSI__GPIO_2_17 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_AUART1_TX__GPIO_3_5 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; spi3_pins_cfa10049: spi3-cfa10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x0183 /* MX28_PAD_GPMI_RDN__GPIO_0_24 */ - 0x01c3 /* MX28_PAD_GPMI_RESETN__GPIO_0_28 */ - 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */ - 0x01a3 /* MX28_PAD_GPMI_ALE__GPIO_0_26 */ - 0x01b3 /* MX28_PAD_GPMI_CLE__GPIO_0_27 */ + MX28_PAD_GPMI_RDN__GPIO_0_24 + MX28_PAD_GPMI_RESETN__GPIO_0_28 + MX28_PAD_GPMI_CE1N__GPIO_0_17 + MX28_PAD_GPMI_ALE__GPIO_0_26 + MX28_PAD_GPMI_CLE__GPIO_0_27 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; lcdif_18bit_pins_cfa10049: lcdif-18bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_cfa10049: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 { reg = <0>; fsl,pinmux-ids = < - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + MX28_PAD_LCD_RESET__GPIO_3_30 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; w1_gpio_pins: w1-gpio@0 { reg = <0>; fsl,pinmux-ids = < - 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */ + MX28_PAD_LCD_D21__GPIO_1_21 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <0>; /* 0 will enable the keeper */ + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */ }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts index 171bcbe..c3900e7 100644 --- a/arch/arm/boot/dts/imx28-cfa10055.dts +++ b/arch/arm/boot/dts/imx28-cfa10055.dts @@ -14,7 +14,7 @@ * The CFA-10055 is an expansion board for the CFA-10036 module and * CFA-10037, thus we need to include the CFA-10037 DTS. */ -/include/ "imx28-cfa10037.dts" +#include "imx28-cfa10037.dts" / { model = "Crystalfontz CFA-10055 Board"; @@ -26,64 +26,64 @@ spi2_pins_cfa10055: spi2-cfa10055@0 { reg = <0>; fsl,pinmux-ids = < - 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */ - 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */ - 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */ - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_SSP2_SCK__GPIO_2_16 + MX28_PAD_SSP2_MOSI__GPIO_2_17 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_AUART1_TX__GPIO_3_5 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; lcdif_18bit_pins_cfa10055: lcdif-18bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_cfa10055: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 { reg = <0>; fsl,pinmux-ids = < - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + MX28_PAD_LCD_RESET__GPIO_3_30 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts index b45dd0e..cef959a 100644 --- a/arch/arm/boot/dts/imx28-cfa10056.dts +++ b/arch/arm/boot/dts/imx28-cfa10056.dts @@ -13,7 +13,7 @@ * The CFA-10055 is an expansion board for the CFA-10036 module and * CFA-10037, thus we need to include the CFA-10037 DTS. */ -/include/ "imx28-cfa10037.dts" +#include "imx28-cfa10037.dts" / { model = "Crystalfontz CFA-10056 Board"; @@ -25,37 +25,37 @@ spi2_pins_cfa10056: spi2-cfa10056@0 { reg = <0>; fsl,pinmux-ids = < - 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */ - 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */ - 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */ - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_SSP2_SCK__GPIO_2_16 + MX28_PAD_SSP2_MOSI__GPIO_2_17 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_AUART1_TX__GPIO_3_5 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; lcdif_pins_cfa10056: lcdif-10056@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 { reg = <0>; fsl,pinmux-ids = < - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + MX28_PAD_LCD_RESET__GPIO_3_30 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts index 0333c05..3c13128 100644 --- a/arch/arm/boot/dts/imx28-cfa10057.dts +++ b/arch/arm/boot/dts/imx28-cfa10057.dts @@ -14,7 +14,7 @@ * The CFA-10057 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10057 Board"; @@ -26,51 +26,51 @@ usb_pins_cfa10057: usb-10057@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_18bit_pins_cfa10057: lcdif-18bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_cfa10057: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts index 64c64c5..2469d34 100644 --- a/arch/arm/boot/dts/imx28-cfa10058.dts +++ b/arch/arm/boot/dts/imx28-cfa10058.dts @@ -14,7 +14,7 @@ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10058 Board"; @@ -26,24 +26,24 @@ usb_pins_cfa10058: usb-10058@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_cfa10058: lcdif-10058@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index aa33393..4267c2b 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Freescale i.MX28 Evaluation Kit"; @@ -70,52 +70,52 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */ - 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */ - 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */ - 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */ - 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ - 0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */ - 0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */ + MX28_PAD_SSP1_CMD__GPIO_2_13 + MX28_PAD_SSP1_DATA3__GPIO_2_15 + MX28_PAD_ENET0_RX_CLK__GPIO_4_13 + MX28_PAD_SSP1_SCK__GPIO_2_12 + MX28_PAD_PWM3__GPIO_3_28 + MX28_PAD_LCD_RESET__GPIO_3_30 + MX28_PAD_AUART2_RX__GPIO_3_8 + MX28_PAD_AUART2_TX__GPIO_3_9 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; led_pin_gpio3_5: led_gpio3_5@0 { reg = <0>; fsl,pinmux-ids = < - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_AUART1_TX__GPIO_3_5 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; gpmi_pins_evk: gpmi-nand-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */ - 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */ + MX28_PAD_GPMI_CE1N__GPMI_CE1N + MX28_PAD_GPMI_RDY1__GPMI_READY1 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_evk: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; @@ -182,6 +182,7 @@ }; lradc@80050000 { + fsl,lradc-touchscreen-wires = <4>; status = "okay"; fsl,lradc-touchscreen-wires = <4>; fsl,ave-ctrl = <4>; @@ -246,6 +247,8 @@ ahb@80080000 { usb0: usb@80080000 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_pins_a>; vbus-supply = <®_usb0_vbus>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts new file mode 100644 index 0000000..d3958da --- /dev/null +++ b/arch/arm/boot/dts/imx28-m28cu3.dts @@ -0,0 +1,266 @@ +/* + * Copyright (C) 2013 Marek Vasut <marex@denx.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx28.dtsi" + +/ { + model = "MSR M28CU3"; + compatible = "msr,m28cu3", "fsl,imx28"; + + memory { + reg = <0x40000000 0x08000000>; + }; + + apb@80000000 { + apbh@80000000 { + gpmi-nand@8000c000 { + #address-cells = <1>; + #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>; + status = "okay"; + + partition@0 { + label = "gpmi-nfc-0-boot"; + reg = <0x00000000 0x01400000>; + read-only; + }; + + partition@1 { + label = "gpmi-nfc-general-use"; + reg = <0x01400000 0x0ec00000>; + }; + }; + + ssp0: ssp@80010000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a + &mmc0_cd_cfg + &mmc0_sck_cfg>; + bus-width = <4>; + vmmc-supply = <®_vddio_sd0>; + status = "okay"; + }; + + ssp2: ssp@80014000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_4bit_pins_a + &mmc2_cd_cfg + &mmc2_sck_cfg>; + bus-width = <4>; + vmmc-supply = <®_vddio_sd1>; + status = "okay"; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP2_SS0__GPIO_2_19 + MX28_PAD_PWM4__GPIO_3_29 + MX28_PAD_AUART2_RX__GPIO_3_8 + MX28_PAD_ENET0_RX_CLK__GPIO_4_13 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_pins_m28: lcdif-m28@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_VSYNC__LCD_VSYNC + MX28_PAD_LCD_HSYNC__LCD_HSYNC + MX28_PAD_LCD_DOTCLK__LCD_DOTCLK + MX28_PAD_LCD_RESET__LCD_RESET + MX28_PAD_LCD_CS__LCD_ENABLE + MX28_PAD_AUART1_TX__GPIO_3_5 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + led_pins_gpio: leds-m28@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP3_MISO__GPIO_2_26 + MX28_PAD_SSP3_SCK__GPIO_2_24 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + }; + + ocotp@8002c000 { + status = "okay"; + }; + + lcdif@80030000 { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a + &lcdif_pins_m28>; + display = <&display>; + reset-active-high; + status = "okay"; + + display: display0 { + bits-per-pixel = <32>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <6410256>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hfront-porch = <20>; + vback-porch = <15>; + vfront-porch = <5>; + hsync-len = <30>; + vsync-len = <3>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; + }; + }; + + apbx@80040000 { + duart: serial@80074000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_b>; + status = "okay"; + }; + + usbphy1: usbphy@8007e000 { + status = "okay"; + }; + + auart0: serial@8006a000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + status = "okay"; + }; + + auart3: serial@80070000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart3_2pins_b>; + status = "okay"; + }; + + pwm: pwm@80064000 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pins_a>; + status = "okay"; + }; + }; + }; + + ahb@80080000 { + usb1: usb@80090000 { + vbus-supply = <®_usb1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&usbphy1_pins_a>; + disable-over-current; + status = "okay"; + }; + + mac0: ethernet@800f0000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + phy-reset-gpios = <&gpio4 13 0>; + phy-reset-duration = <100>; + status = "okay"; + }; + + mac1: ethernet@800f4000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac1_pins_a>; + status = "okay"; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 3 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_gpio>; + + user1 { + label = "sd0-led"; + gpios = <&gpio2 26 0>; + linux,default-trigger = "mmc0"; + }; + + user2 { + label = "sd1-led"; + gpios = <&gpio2 24 0>; + linux,default-trigger = "mmc2"; + }; + }; + + regulators { + compatible = "simple-bus"; + + reg_3p3v: 3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vddio_sd0: vddio-sd0 { + compatible = "regulator-fixed"; + regulator-name = "vddio-sd0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 29 0>; + }; + + reg_vddio_sd1: vddio-sd1 { + compatible = "regulator-fixed"; + regulator-name = "vddio-sd1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 0>; + }; + + reg_usb1_vbus: usb1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 8 0>; + enable-active-high; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index 0d322a2..8e2477f 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "DENX M28EVK"; @@ -92,26 +92,26 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ - 0x30a3 /* MX28_PAD_AUART2_CTS__GPIO_3_10 */ - 0x30b3 /* MX28_PAD_AUART2_RTS__GPIO_3_11 */ - 0x30c3 /* MX28_PAD_AUART3_RX__GPIO_3_12 */ - 0x30d3 /* MX28_PAD_AUART3_TX__GPIO_3_13 */ + MX28_PAD_PWM3__GPIO_3_28 + MX28_PAD_AUART2_CTS__GPIO_3_10 + MX28_PAD_AUART2_RTS__GPIO_3_11 + MX28_PAD_AUART3_RX__GPIO_3_12 + MX28_PAD_AUART3_TX__GPIO_3_13 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_pins_m28: lcdif-m28@0 { reg = <0>; fsl,pinmux-ids = < - 0x11e0 /* MX28_PAD_LCD_DOTCLK__LCD_DOTCLK */ - 0x11f0 /* MX28_PAD_LCD_ENABLE__LCD_ENABLE */ + MX28_PAD_LCD_DOTCLK__LCD_DOTCLK + MX28_PAD_LCD_ENABLE__LCD_ENABLE >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-pinfunc.h b/arch/arm/boot/dts/imx28-pinfunc.h new file mode 100644 index 0000000..e11f69b --- /dev/null +++ b/arch/arm/boot/dts/imx28-pinfunc.h @@ -0,0 +1,506 @@ +/* + * Header providing constants for i.MX28 pinctrl bindings. + * + * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DT_BINDINGS_MX28_PINCTRL_H__ +#define __DT_BINDINGS_MX28_PINCTRL_H__ + +#include "mxs-pinfunc.h" + +#define MX28_PAD_GPMI_D00__GPMI_D0 0x0000 +#define MX28_PAD_GPMI_D01__GPMI_D1 0x0010 +#define MX28_PAD_GPMI_D02__GPMI_D2 0x0020 +#define MX28_PAD_GPMI_D03__GPMI_D3 0x0030 +#define MX28_PAD_GPMI_D04__GPMI_D4 0x0040 +#define MX28_PAD_GPMI_D05__GPMI_D5 0x0050 +#define MX28_PAD_GPMI_D06__GPMI_D6 0x0060 +#define MX28_PAD_GPMI_D07__GPMI_D7 0x0070 +#define MX28_PAD_GPMI_CE0N__GPMI_CE0N 0x0100 +#define MX28_PAD_GPMI_CE1N__GPMI_CE1N 0x0110 +#define MX28_PAD_GPMI_CE2N__GPMI_CE2N 0x0120 +#define MX28_PAD_GPMI_CE3N__GPMI_CE3N 0x0130 +#define MX28_PAD_GPMI_RDY0__GPMI_READY0 0x0140 +#define MX28_PAD_GPMI_RDY1__GPMI_READY1 0x0150 +#define MX28_PAD_GPMI_RDY2__GPMI_READY2 0x0160 +#define MX28_PAD_GPMI_RDY3__GPMI_READY3 0x0170 +#define MX28_PAD_GPMI_RDN__GPMI_RDN 0x0180 +#define MX28_PAD_GPMI_WRN__GPMI_WRN 0x0190 +#define MX28_PAD_GPMI_ALE__GPMI_ALE 0x01a0 +#define MX28_PAD_GPMI_CLE__GPMI_CLE 0x01b0 +#define MX28_PAD_GPMI_RESETN__GPMI_RESETN 0x01c0 +#define MX28_PAD_LCD_D00__LCD_D0 0x1000 +#define MX28_PAD_LCD_D01__LCD_D1 0x1010 +#define MX28_PAD_LCD_D02__LCD_D2 0x1020 +#define MX28_PAD_LCD_D03__LCD_D3 0x1030 +#define MX28_PAD_LCD_D04__LCD_D4 0x1040 +#define MX28_PAD_LCD_D05__LCD_D5 0x1050 +#define MX28_PAD_LCD_D06__LCD_D6 0x1060 +#define MX28_PAD_LCD_D07__LCD_D7 0x1070 +#define MX28_PAD_LCD_D08__LCD_D8 0x1080 +#define MX28_PAD_LCD_D09__LCD_D9 0x1090 +#define MX28_PAD_LCD_D10__LCD_D10 0x10a0 +#define MX28_PAD_LCD_D11__LCD_D11 0x10b0 +#define MX28_PAD_LCD_D12__LCD_D12 0x10c0 +#define MX28_PAD_LCD_D13__LCD_D13 0x10d0 +#define MX28_PAD_LCD_D14__LCD_D14 0x10e0 +#define MX28_PAD_LCD_D15__LCD_D15 0x10f0 +#define MX28_PAD_LCD_D16__LCD_D16 0x1100 +#define MX28_PAD_LCD_D17__LCD_D17 0x1110 +#define MX28_PAD_LCD_D18__LCD_D18 0x1120 +#define MX28_PAD_LCD_D19__LCD_D19 0x1130 +#define MX28_PAD_LCD_D20__LCD_D20 0x1140 +#define MX28_PAD_LCD_D21__LCD_D21 0x1150 +#define MX28_PAD_LCD_D22__LCD_D22 0x1160 +#define MX28_PAD_LCD_D23__LCD_D23 0x1170 +#define MX28_PAD_LCD_RD_E__LCD_RD_E 0x1180 +#define MX28_PAD_LCD_WR_RWN__LCD_WR_RWN 0x1190 +#define MX28_PAD_LCD_RS__LCD_RS 0x11a0 +#define MX28_PAD_LCD_CS__LCD_CS 0x11b0 +#define MX28_PAD_LCD_VSYNC__LCD_VSYNC 0x11c0 +#define MX28_PAD_LCD_HSYNC__LCD_HSYNC 0x11d0 +#define MX28_PAD_LCD_DOTCLK__LCD_DOTCLK 0x11e0 +#define MX28_PAD_LCD_ENABLE__LCD_ENABLE 0x11f0 +#define MX28_PAD_SSP0_DATA0__SSP0_D0 0x2000 +#define MX28_PAD_SSP0_DATA1__SSP0_D1 0x2010 +#define MX28_PAD_SSP0_DATA2__SSP0_D2 0x2020 +#define MX28_PAD_SSP0_DATA3__SSP0_D3 0x2030 +#define MX28_PAD_SSP0_DATA4__SSP0_D4 0x2040 +#define MX28_PAD_SSP0_DATA5__SSP0_D5 0x2050 +#define MX28_PAD_SSP0_DATA6__SSP0_D6 0x2060 +#define MX28_PAD_SSP0_DATA7__SSP0_D7 0x2070 +#define MX28_PAD_SSP0_CMD__SSP0_CMD 0x2080 +#define MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT 0x2090 +#define MX28_PAD_SSP0_SCK__SSP0_SCK 0x20a0 +#define MX28_PAD_SSP1_SCK__SSP1_SCK 0x20c0 +#define MX28_PAD_SSP1_CMD__SSP1_CMD 0x20d0 +#define MX28_PAD_SSP1_DATA0__SSP1_D0 0x20e0 +#define MX28_PAD_SSP1_DATA3__SSP1_D3 0x20f0 +#define MX28_PAD_SSP2_SCK__SSP2_SCK 0x2100 +#define MX28_PAD_SSP2_MOSI__SSP2_CMD 0x2110 +#define MX28_PAD_SSP2_MISO__SSP2_D0 0x2120 +#define MX28_PAD_SSP2_SS0__SSP2_D3 0x2130 +#define MX28_PAD_SSP2_SS1__SSP2_D4 0x2140 +#define MX28_PAD_SSP2_SS2__SSP2_D5 0x2150 +#define MX28_PAD_SSP3_SCK__SSP3_SCK 0x2180 +#define MX28_PAD_SSP3_MOSI__SSP3_CMD 0x2190 +#define MX28_PAD_SSP3_MISO__SSP3_D0 0x21a0 +#define MX28_PAD_SSP3_SS0__SSP3_D3 0x21b0 +#define MX28_PAD_AUART0_RX__AUART0_RX 0x3000 +#define MX28_PAD_AUART0_TX__AUART0_TX 0x3010 +#define MX28_PAD_AUART0_CTS__AUART0_CTS 0x3020 +#define MX28_PAD_AUART0_RTS__AUART0_RTS 0x3030 +#define MX28_PAD_AUART1_RX__AUART1_RX 0x3040 +#define MX28_PAD_AUART1_TX__AUART1_TX 0x3050 +#define MX28_PAD_AUART1_CTS__AUART1_CTS 0x3060 +#define MX28_PAD_AUART1_RTS__AUART1_RTS 0x3070 +#define MX28_PAD_AUART2_RX__AUART2_RX 0x3080 +#define MX28_PAD_AUART2_TX__AUART2_TX 0x3090 +#define MX28_PAD_AUART2_CTS__AUART2_CTS 0x30a0 +#define MX28_PAD_AUART2_RTS__AUART2_RTS 0x30b0 +#define MX28_PAD_AUART3_RX__AUART3_RX 0x30c0 +#define MX28_PAD_AUART3_TX__AUART3_TX 0x30d0 +#define MX28_PAD_AUART3_CTS__AUART3_CTS 0x30e0 +#define MX28_PAD_AUART3_RTS__AUART3_RTS 0x30f0 +#define MX28_PAD_PWM0__PWM_0 0x3100 +#define MX28_PAD_PWM1__PWM_1 0x3110 +#define MX28_PAD_PWM2__PWM_2 0x3120 +#define MX28_PAD_SAIF0_MCLK__SAIF0_MCLK 0x3140 +#define MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK 0x3150 +#define MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK 0x3160 +#define MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 0x3170 +#define MX28_PAD_I2C0_SCL__I2C0_SCL 0x3180 +#define MX28_PAD_I2C0_SDA__I2C0_SDA 0x3190 +#define MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 0x31a0 +#define MX28_PAD_SPDIF__SPDIF_TX 0x31b0 +#define MX28_PAD_PWM3__PWM_3 0x31c0 +#define MX28_PAD_PWM4__PWM_4 0x31d0 +#define MX28_PAD_LCD_RESET__LCD_RESET 0x31e0 +#define MX28_PAD_ENET0_MDC__ENET0_MDC 0x4000 +#define MX28_PAD_ENET0_MDIO__ENET0_MDIO 0x4010 +#define MX28_PAD_ENET0_RX_EN__ENET0_RX_EN 0x4020 +#define MX28_PAD_ENET0_RXD0__ENET0_RXD0 0x4030 +#define MX28_PAD_ENET0_RXD1__ENET0_RXD1 0x4040 +#define MX28_PAD_ENET0_TX_CLK__ENET0_TX_CLK 0x4050 +#define MX28_PAD_ENET0_TX_EN__ENET0_TX_EN 0x4060 +#define MX28_PAD_ENET0_TXD0__ENET0_TXD0 0x4070 +#define MX28_PAD_ENET0_TXD1__ENET0_TXD1 0x4080 +#define MX28_PAD_ENET0_RXD2__ENET0_RXD2 0x4090 +#define MX28_PAD_ENET0_RXD3__ENET0_RXD3 0x40a0 +#define MX28_PAD_ENET0_TXD2__ENET0_TXD2 0x40b0 +#define MX28_PAD_ENET0_TXD3__ENET0_TXD3 0x40c0 +#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_CLK 0x40d0 +#define MX28_PAD_ENET0_COL__ENET0_COL 0x40e0 +#define MX28_PAD_ENET0_CRS__ENET0_CRS 0x40f0 +#define MX28_PAD_ENET_CLK__CLKCTRL_ENET 0x4100 +#define MX28_PAD_JTAG_RTCK__JTAG_RTCK 0x4140 +#define MX28_PAD_EMI_D00__EMI_DATA0 0x5000 +#define MX28_PAD_EMI_D01__EMI_DATA1 0x5010 +#define MX28_PAD_EMI_D02__EMI_DATA2 0x5020 +#define MX28_PAD_EMI_D03__EMI_DATA3 0x5030 +#define MX28_PAD_EMI_D04__EMI_DATA4 0x5040 +#define MX28_PAD_EMI_D05__EMI_DATA5 0x5050 +#define MX28_PAD_EMI_D06__EMI_DATA6 0x5060 +#define MX28_PAD_EMI_D07__EMI_DATA7 0x5070 +#define MX28_PAD_EMI_D08__EMI_DATA8 0x5080 +#define MX28_PAD_EMI_D09__EMI_DATA9 0x5090 +#define MX28_PAD_EMI_D10__EMI_DATA10 0x50a0 +#define MX28_PAD_EMI_D11__EMI_DATA11 0x50b0 +#define MX28_PAD_EMI_D12__EMI_DATA12 0x50c0 +#define MX28_PAD_EMI_D13__EMI_DATA13 0x50d0 +#define MX28_PAD_EMI_D14__EMI_DATA14 0x50e0 +#define MX28_PAD_EMI_D15__EMI_DATA15 0x50f0 +#define MX28_PAD_EMI_ODT0__EMI_ODT0 0x5100 +#define MX28_PAD_EMI_DQM0__EMI_DQM0 0x5110 +#define MX28_PAD_EMI_ODT1__EMI_ODT1 0x5120 +#define MX28_PAD_EMI_DQM1__EMI_DQM1 0x5130 +#define MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK 0x5140 +#define MX28_PAD_EMI_CLK__EMI_CLK 0x5150 +#define MX28_PAD_EMI_DQS0__EMI_DQS0 0x5160 +#define MX28_PAD_EMI_DQS1__EMI_DQS1 0x5170 +#define MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN 0x51a0 +#define MX28_PAD_EMI_A00__EMI_ADDR0 0x6000 +#define MX28_PAD_EMI_A01__EMI_ADDR1 0x6010 +#define MX28_PAD_EMI_A02__EMI_ADDR2 0x6020 +#define MX28_PAD_EMI_A03__EMI_ADDR3 0x6030 +#define MX28_PAD_EMI_A04__EMI_ADDR4 0x6040 +#define MX28_PAD_EMI_A05__EMI_ADDR5 0x6050 +#define MX28_PAD_EMI_A06__EMI_ADDR6 0x6060 +#define MX28_PAD_EMI_A07__EMI_ADDR7 0x6070 +#define MX28_PAD_EMI_A08__EMI_ADDR8 0x6080 +#define MX28_PAD_EMI_A09__EMI_ADDR9 0x6090 +#define MX28_PAD_EMI_A10__EMI_ADDR10 0x60a0 +#define MX28_PAD_EMI_A11__EMI_ADDR11 0x60b0 +#define MX28_PAD_EMI_A12__EMI_ADDR12 0x60c0 +#define MX28_PAD_EMI_A13__EMI_ADDR13 0x60d0 +#define MX28_PAD_EMI_A14__EMI_ADDR14 0x60e0 +#define MX28_PAD_EMI_BA0__EMI_BA0 0x6100 +#define MX28_PAD_EMI_BA1__EMI_BA1 0x6110 +#define MX28_PAD_EMI_BA2__EMI_BA2 0x6120 +#define MX28_PAD_EMI_CASN__EMI_CASN 0x6130 +#define MX28_PAD_EMI_RASN__EMI_RASN 0x6140 +#define MX28_PAD_EMI_WEN__EMI_WEN 0x6150 +#define MX28_PAD_EMI_CE0N__EMI_CE0N 0x6160 +#define MX28_PAD_EMI_CE1N__EMI_CE1N 0x6170 +#define MX28_PAD_EMI_CKE__EMI_CKE 0x6180 +#define MX28_PAD_GPMI_D00__SSP1_D0 0x0001 +#define MX28_PAD_GPMI_D01__SSP1_D1 0x0011 +#define MX28_PAD_GPMI_D02__SSP1_D2 0x0021 +#define MX28_PAD_GPMI_D03__SSP1_D3 0x0031 +#define MX28_PAD_GPMI_D04__SSP1_D4 0x0041 +#define MX28_PAD_GPMI_D05__SSP1_D5 0x0051 +#define MX28_PAD_GPMI_D06__SSP1_D6 0x0061 +#define MX28_PAD_GPMI_D07__SSP1_D7 0x0071 +#define MX28_PAD_GPMI_CE0N__SSP3_D0 0x0101 +#define MX28_PAD_GPMI_CE1N__SSP3_D3 0x0111 +#define MX28_PAD_GPMI_CE2N__CAN1_TX 0x0121 +#define MX28_PAD_GPMI_CE3N__CAN1_RX 0x0131 +#define MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT 0x0141 +#define MX28_PAD_GPMI_RDY1__SSP1_CMD 0x0151 +#define MX28_PAD_GPMI_RDY2__CAN0_TX 0x0161 +#define MX28_PAD_GPMI_RDY3__CAN0_RX 0x0171 +#define MX28_PAD_GPMI_RDN__SSP3_SCK 0x0181 +#define MX28_PAD_GPMI_WRN__SSP1_SCK 0x0191 +#define MX28_PAD_GPMI_ALE__SSP3_D1 0x01a1 +#define MX28_PAD_GPMI_CLE__SSP3_D2 0x01b1 +#define MX28_PAD_GPMI_RESETN__SSP3_CMD 0x01c1 +#define MX28_PAD_LCD_D03__ETM_DA8 0x1031 +#define MX28_PAD_LCD_D04__ETM_DA9 0x1041 +#define MX28_PAD_LCD_D08__ETM_DA3 0x1081 +#define MX28_PAD_LCD_D09__ETM_DA4 0x1091 +#define MX28_PAD_LCD_D20__ENET1_1588_EVENT2_OUT 0x1141 +#define MX28_PAD_LCD_D21__ENET1_1588_EVENT2_IN 0x1151 +#define MX28_PAD_LCD_D22__ENET1_1588_EVENT3_OUT 0x1161 +#define MX28_PAD_LCD_D23__ENET1_1588_EVENT3_IN 0x1171 +#define MX28_PAD_LCD_RD_E__LCD_VSYNC 0x1181 +#define MX28_PAD_LCD_WR_RWN__LCD_HSYNC 0x1191 +#define MX28_PAD_LCD_RS__LCD_DOTCLK 0x11a1 +#define MX28_PAD_LCD_CS__LCD_ENABLE 0x11b1 +#define MX28_PAD_LCD_VSYNC__SAIF1_SDATA0 0x11c1 +#define MX28_PAD_LCD_HSYNC__SAIF1_SDATA1 0x11d1 +#define MX28_PAD_LCD_DOTCLK__SAIF1_MCLK 0x11e1 +#define MX28_PAD_SSP0_DATA4__SSP2_D0 0x2041 +#define MX28_PAD_SSP0_DATA5__SSP2_D3 0x2051 +#define MX28_PAD_SSP0_DATA6__SSP2_CMD 0x2061 +#define MX28_PAD_SSP0_DATA7__SSP2_SCK 0x2071 +#define MX28_PAD_SSP1_SCK__SSP2_D1 0x20c1 +#define MX28_PAD_SSP1_CMD__SSP2_D2 0x20d1 +#define MX28_PAD_SSP1_DATA0__SSP2_D6 0x20e1 +#define MX28_PAD_SSP1_DATA3__SSP2_D7 0x20f1 +#define MX28_PAD_SSP2_SCK__AUART2_RX 0x2101 +#define MX28_PAD_SSP2_MOSI__AUART2_TX 0x2111 +#define MX28_PAD_SSP2_MISO__AUART3_RX 0x2121 +#define MX28_PAD_SSP2_SS0__AUART3_TX 0x2131 +#define MX28_PAD_SSP2_SS1__SSP2_D1 0x2141 +#define MX28_PAD_SSP2_SS2__SSP2_D2 0x2151 +#define MX28_PAD_SSP3_SCK__AUART4_TX 0x2181 +#define MX28_PAD_SSP3_MOSI__AUART4_RX 0x2191 +#define MX28_PAD_SSP3_MISO__AUART4_RTS 0x21a1 +#define MX28_PAD_SSP3_SS0__AUART4_CTS 0x21b1 +#define MX28_PAD_AUART0_RX__I2C0_SCL 0x3001 +#define MX28_PAD_AUART0_TX__I2C0_SDA 0x3011 +#define MX28_PAD_AUART0_CTS__AUART4_RX 0x3021 +#define MX28_PAD_AUART0_RTS__AUART4_TX 0x3031 +#define MX28_PAD_AUART1_RX__SSP2_CARD_DETECT 0x3041 +#define MX28_PAD_AUART1_TX__SSP3_CARD_DETECT 0x3051 +#define MX28_PAD_AUART1_CTS__USB0_OVERCURRENT 0x3061 +#define MX28_PAD_AUART1_RTS__USB0_ID 0x3071 +#define MX28_PAD_AUART2_RX__SSP3_D1 0x3081 +#define MX28_PAD_AUART2_TX__SSP3_D2 0x3091 +#define MX28_PAD_AUART2_CTS__I2C1_SCL 0x30a1 +#define MX28_PAD_AUART2_RTS__I2C1_SDA 0x30b1 +#define MX28_PAD_AUART3_RX__CAN0_TX 0x30c1 +#define MX28_PAD_AUART3_TX__CAN0_RX 0x30d1 +#define MX28_PAD_AUART3_CTS__CAN1_TX 0x30e1 +#define MX28_PAD_AUART3_RTS__CAN1_RX 0x30f1 +#define MX28_PAD_PWM0__I2C1_SCL 0x3101 +#define MX28_PAD_PWM1__I2C1_SDA 0x3111 +#define MX28_PAD_PWM2__USB0_ID 0x3121 +#define MX28_PAD_SAIF0_MCLK__PWM_3 0x3141 +#define MX28_PAD_SAIF0_LRCLK__PWM_4 0x3151 +#define MX28_PAD_SAIF0_BITCLK__PWM_5 0x3161 +#define MX28_PAD_SAIF0_SDATA0__PWM_6 0x3171 +#define MX28_PAD_I2C0_SCL__TIMROT_ROTARYA 0x3181 +#define MX28_PAD_I2C0_SDA__TIMROT_ROTARYB 0x3191 +#define MX28_PAD_SAIF1_SDATA0__PWM_7 0x31a1 +#define MX28_PAD_LCD_RESET__LCD_VSYNC 0x31e1 +#define MX28_PAD_ENET0_MDC__GPMI_CE4N 0x4001 +#define MX28_PAD_ENET0_MDIO__GPMI_CE5N 0x4011 +#define MX28_PAD_ENET0_RX_EN__GPMI_CE6N 0x4021 +#define MX28_PAD_ENET0_RXD0__GPMI_CE7N 0x4031 +#define MX28_PAD_ENET0_RXD1__GPMI_READY4 0x4041 +#define MX28_PAD_ENET0_TX_CLK__HSADC_TRIGGER 0x4051 +#define MX28_PAD_ENET0_TX_EN__GPMI_READY5 0x4061 +#define MX28_PAD_ENET0_TXD0__GPMI_READY6 0x4071 +#define MX28_PAD_ENET0_TXD1__GPMI_READY7 0x4081 +#define MX28_PAD_ENET0_RXD2__ENET1_RXD0 0x4091 +#define MX28_PAD_ENET0_RXD3__ENET1_RXD1 0x40a1 +#define MX28_PAD_ENET0_TXD2__ENET1_TXD0 0x40b1 +#define MX28_PAD_ENET0_TXD3__ENET1_TXD1 0x40c1 +#define MX28_PAD_ENET0_RX_CLK__ENET0_RX_ER 0x40d1 +#define MX28_PAD_ENET0_COL__ENET1_TX_EN 0x40e1 +#define MX28_PAD_ENET0_CRS__ENET1_RX_EN 0x40f1 +#define MX28_PAD_GPMI_CE2N__ENET0_RX_ER 0x0122 +#define MX28_PAD_GPMI_CE3N__SAIF1_MCLK 0x0132 +#define MX28_PAD_GPMI_RDY0__USB0_ID 0x0142 +#define MX28_PAD_GPMI_RDY2__ENET0_TX_ER 0x0162 +#define MX28_PAD_GPMI_RDY3__HSADC_TRIGGER 0x0172 +#define MX28_PAD_GPMI_ALE__SSP3_D4 0x01a2 +#define MX28_PAD_GPMI_CLE__SSP3_D5 0x01b2 +#define MX28_PAD_LCD_D00__ETM_DA0 0x1002 +#define MX28_PAD_LCD_D01__ETM_DA1 0x1012 +#define MX28_PAD_LCD_D02__ETM_DA2 0x1022 +#define MX28_PAD_LCD_D03__ETM_DA3 0x1032 +#define MX28_PAD_LCD_D04__ETM_DA4 0x1042 +#define MX28_PAD_LCD_D05__ETM_DA5 0x1052 +#define MX28_PAD_LCD_D06__ETM_DA6 0x1062 +#define MX28_PAD_LCD_D07__ETM_DA7 0x1072 +#define MX28_PAD_LCD_D08__ETM_DA8 0x1082 +#define MX28_PAD_LCD_D09__ETM_DA9 0x1092 +#define MX28_PAD_LCD_D10__ETM_DA10 0x10a2 +#define MX28_PAD_LCD_D11__ETM_DA11 0x10b2 +#define MX28_PAD_LCD_D12__ETM_DA12 0x10c2 +#define MX28_PAD_LCD_D13__ETM_DA13 0x10d2 +#define MX28_PAD_LCD_D14__ETM_DA14 0x10e2 +#define MX28_PAD_LCD_D15__ETM_DA15 0x10f2 +#define MX28_PAD_LCD_D16__ETM_DA7 0x1102 +#define MX28_PAD_LCD_D17__ETM_DA6 0x1112 +#define MX28_PAD_LCD_D18__ETM_DA5 0x1122 +#define MX28_PAD_LCD_D19__ETM_DA4 0x1132 +#define MX28_PAD_LCD_D20__ETM_DA3 0x1142 +#define MX28_PAD_LCD_D21__ETM_DA2 0x1152 +#define MX28_PAD_LCD_D22__ETM_DA1 0x1162 +#define MX28_PAD_LCD_D23__ETM_DA0 0x1172 +#define MX28_PAD_LCD_RD_E__ETM_TCTL 0x1182 +#define MX28_PAD_LCD_WR_RWN__ETM_TCLK 0x1192 +#define MX28_PAD_LCD_HSYNC__ETM_TCTL 0x11d2 +#define MX28_PAD_LCD_DOTCLK__ETM_TCLK 0x11e2 +#define MX28_PAD_SSP1_SCK__ENET0_1588_EVENT2_OUT 0x20c2 +#define MX28_PAD_SSP1_CMD__ENET0_1588_EVENT2_IN 0x20d2 +#define MX28_PAD_SSP1_DATA0__ENET0_1588_EVENT3_OUT 0x20e2 +#define MX28_PAD_SSP1_DATA3__ENET0_1588_EVENT3_IN 0x20f2 +#define MX28_PAD_SSP2_SCK__SAIF0_SDATA1 0x2102 +#define MX28_PAD_SSP2_MOSI__SAIF0_SDATA2 0x2112 +#define MX28_PAD_SSP2_MISO__SAIF1_SDATA1 0x2122 +#define MX28_PAD_SSP2_SS0__SAIF1_SDATA2 0x2132 +#define MX28_PAD_SSP2_SS1__USB1_OVERCURRENT 0x2142 +#define MX28_PAD_SSP2_SS2__USB0_OVERCURRENT 0x2152 +#define MX28_PAD_SSP3_SCK__ENET1_1588_EVENT0_OUT 0x2182 +#define MX28_PAD_SSP3_MOSI__ENET1_1588_EVENT0_IN 0x2192 +#define MX28_PAD_SSP3_MISO__ENET1_1588_EVENT1_OUT 0x21a2 +#define MX28_PAD_SSP3_SS0__ENET1_1588_EVENT1_IN 0x21b2 +#define MX28_PAD_AUART0_RX__DUART_CTS 0x3002 +#define MX28_PAD_AUART0_TX__DUART_RTS 0x3012 +#define MX28_PAD_AUART0_CTS__DUART_RX 0x3022 +#define MX28_PAD_AUART0_RTS__DUART_TX 0x3032 +#define MX28_PAD_AUART1_RX__PWM_0 0x3042 +#define MX28_PAD_AUART1_TX__PWM_1 0x3052 +#define MX28_PAD_AUART1_CTS__TIMROT_ROTARYA 0x3062 +#define MX28_PAD_AUART1_RTS__TIMROT_ROTARYB 0x3072 +#define MX28_PAD_AUART2_RX__SSP3_D4 0x3082 +#define MX28_PAD_AUART2_TX__SSP3_D5 0x3092 +#define MX28_PAD_AUART2_CTS__SAIF1_BITCLK 0x30a2 +#define MX28_PAD_AUART2_RTS__SAIF1_LRCLK 0x30b2 +#define MX28_PAD_AUART3_RX__ENET0_1588_EVENT0_OUT 0x30c2 +#define MX28_PAD_AUART3_TX__ENET0_1588_EVENT0_IN 0x30d2 +#define MX28_PAD_AUART3_CTS__ENET0_1588_EVENT1_OUT 0x30e2 +#define MX28_PAD_AUART3_RTS__ENET0_1588_EVENT1_IN 0x30f2 +#define MX28_PAD_PWM0__DUART_RX 0x3102 +#define MX28_PAD_PWM1__DUART_TX 0x3112 +#define MX28_PAD_PWM2__USB1_OVERCURRENT 0x3122 +#define MX28_PAD_SAIF0_MCLK__AUART4_CTS 0x3142 +#define MX28_PAD_SAIF0_LRCLK__AUART4_RTS 0x3152 +#define MX28_PAD_SAIF0_BITCLK__AUART4_RX 0x3162 +#define MX28_PAD_SAIF0_SDATA0__AUART4_TX 0x3172 +#define MX28_PAD_I2C0_SCL__DUART_RX 0x3182 +#define MX28_PAD_I2C0_SDA__DUART_TX 0x3192 +#define MX28_PAD_SAIF1_SDATA0__SAIF0_SDATA1 0x31a2 +#define MX28_PAD_SPDIF__ENET1_RX_ER 0x31b2 +#define MX28_PAD_ENET0_MDC__SAIF0_SDATA1 0x4002 +#define MX28_PAD_ENET0_MDIO__SAIF0_SDATA2 0x4012 +#define MX28_PAD_ENET0_RX_EN__SAIF1_SDATA1 0x4022 +#define MX28_PAD_ENET0_RXD0__SAIF1_SDATA2 0x4032 +#define MX28_PAD_ENET0_TX_CLK__ENET0_1588_EVENT2_OUT 0x4052 +#define MX28_PAD_ENET0_RXD2__ENET0_1588_EVENT0_OUT 0x4092 +#define MX28_PAD_ENET0_RXD3__ENET0_1588_EVENT0_IN 0x40a2 +#define MX28_PAD_ENET0_TXD2__ENET0_1588_EVENT1_OUT 0x40b2 +#define MX28_PAD_ENET0_TXD3__ENET0_1588_EVENT1_IN 0x40c2 +#define MX28_PAD_ENET0_RX_CLK__ENET0_1588_EVENT2_IN 0x40d2 +#define MX28_PAD_ENET0_COL__ENET0_1588_EVENT3_OUT 0x40e2 +#define MX28_PAD_ENET0_CRS__ENET0_1588_EVENT3_IN 0x40f2 +#define MX28_PAD_GPMI_D00__GPIO_0_0 0x0003 +#define MX28_PAD_GPMI_D01__GPIO_0_1 0x0013 +#define MX28_PAD_GPMI_D02__GPIO_0_2 0x0023 +#define MX28_PAD_GPMI_D03__GPIO_0_3 0x0033 +#define MX28_PAD_GPMI_D04__GPIO_0_4 0x0043 +#define MX28_PAD_GPMI_D05__GPIO_0_5 0x0053 +#define MX28_PAD_GPMI_D06__GPIO_0_6 0x0063 +#define MX28_PAD_GPMI_D07__GPIO_0_7 0x0073 +#define MX28_PAD_GPMI_CE0N__GPIO_0_16 0x0103 +#define MX28_PAD_GPMI_CE1N__GPIO_0_17 0x0113 +#define MX28_PAD_GPMI_CE2N__GPIO_0_18 0x0123 +#define MX28_PAD_GPMI_CE3N__GPIO_0_19 0x0133 +#define MX28_PAD_GPMI_RDY0__GPIO_0_20 0x0143 +#define MX28_PAD_GPMI_RDY1__GPIO_0_21 0x0153 +#define MX28_PAD_GPMI_RDY2__GPIO_0_22 0x0163 +#define MX28_PAD_GPMI_RDY3__GPIO_0_23 0x0173 +#define MX28_PAD_GPMI_RDN__GPIO_0_24 0x0183 +#define MX28_PAD_GPMI_WRN__GPIO_0_25 0x0193 +#define MX28_PAD_GPMI_ALE__GPIO_0_26 0x01a3 +#define MX28_PAD_GPMI_CLE__GPIO_0_27 0x01b3 +#define MX28_PAD_GPMI_RESETN__GPIO_0_28 0x01c3 +#define MX28_PAD_LCD_D00__GPIO_1_0 0x1003 +#define MX28_PAD_LCD_D01__GPIO_1_1 0x1013 +#define MX28_PAD_LCD_D02__GPIO_1_2 0x1023 +#define MX28_PAD_LCD_D03__GPIO_1_3 0x1033 +#define MX28_PAD_LCD_D04__GPIO_1_4 0x1043 +#define MX28_PAD_LCD_D05__GPIO_1_5 0x1053 +#define MX28_PAD_LCD_D06__GPIO_1_6 0x1063 +#define MX28_PAD_LCD_D07__GPIO_1_7 0x1073 +#define MX28_PAD_LCD_D08__GPIO_1_8 0x1083 +#define MX28_PAD_LCD_D09__GPIO_1_9 0x1093 +#define MX28_PAD_LCD_D10__GPIO_1_10 0x10a3 +#define MX28_PAD_LCD_D11__GPIO_1_11 0x10b3 +#define MX28_PAD_LCD_D12__GPIO_1_12 0x10c3 +#define MX28_PAD_LCD_D13__GPIO_1_13 0x10d3 +#define MX28_PAD_LCD_D14__GPIO_1_14 0x10e3 +#define MX28_PAD_LCD_D15__GPIO_1_15 0x10f3 +#define MX28_PAD_LCD_D16__GPIO_1_16 0x1103 +#define MX28_PAD_LCD_D17__GPIO_1_17 0x1113 +#define MX28_PAD_LCD_D18__GPIO_1_18 0x1123 +#define MX28_PAD_LCD_D19__GPIO_1_19 0x1133 +#define MX28_PAD_LCD_D20__GPIO_1_20 0x1143 +#define MX28_PAD_LCD_D21__GPIO_1_21 0x1153 +#define MX28_PAD_LCD_D22__GPIO_1_22 0x1163 +#define MX28_PAD_LCD_D23__GPIO_1_23 0x1173 +#define MX28_PAD_LCD_RD_E__GPIO_1_24 0x1183 +#define MX28_PAD_LCD_WR_RWN__GPIO_1_25 0x1193 +#define MX28_PAD_LCD_RS__GPIO_1_26 0x11a3 +#define MX28_PAD_LCD_CS__GPIO_1_27 0x11b3 +#define MX28_PAD_LCD_VSYNC__GPIO_1_28 0x11c3 +#define MX28_PAD_LCD_HSYNC__GPIO_1_29 0x11d3 +#define MX28_PAD_LCD_DOTCLK__GPIO_1_30 0x11e3 +#define MX28_PAD_LCD_ENABLE__GPIO_1_31 0x11f3 +#define MX28_PAD_SSP0_DATA0__GPIO_2_0 0x2003 +#define MX28_PAD_SSP0_DATA1__GPIO_2_1 0x2013 +#define MX28_PAD_SSP0_DATA2__GPIO_2_2 0x2023 +#define MX28_PAD_SSP0_DATA3__GPIO_2_3 0x2033 +#define MX28_PAD_SSP0_DATA4__GPIO_2_4 0x2043 +#define MX28_PAD_SSP0_DATA5__GPIO_2_5 0x2053 +#define MX28_PAD_SSP0_DATA6__GPIO_2_6 0x2063 +#define MX28_PAD_SSP0_DATA7__GPIO_2_7 0x2073 +#define MX28_PAD_SSP0_CMD__GPIO_2_8 0x2083 +#define MX28_PAD_SSP0_DETECT__GPIO_2_9 0x2093 +#define MX28_PAD_SSP0_SCK__GPIO_2_10 0x20a3 +#define MX28_PAD_SSP1_SCK__GPIO_2_12 0x20c3 +#define MX28_PAD_SSP1_CMD__GPIO_2_13 0x20d3 +#define MX28_PAD_SSP1_DATA0__GPIO_2_14 0x20e3 +#define MX28_PAD_SSP1_DATA3__GPIO_2_15 0x20f3 +#define MX28_PAD_SSP2_SCK__GPIO_2_16 0x2103 +#define MX28_PAD_SSP2_MOSI__GPIO_2_17 0x2113 +#define MX28_PAD_SSP2_MISO__GPIO_2_18 0x2123 +#define MX28_PAD_SSP2_SS0__GPIO_2_19 0x2133 +#define MX28_PAD_SSP2_SS1__GPIO_2_20 0x2143 +#define MX28_PAD_SSP2_SS2__GPIO_2_21 0x2153 +#define MX28_PAD_SSP3_SCK__GPIO_2_24 0x2183 +#define MX28_PAD_SSP3_MOSI__GPIO_2_25 0x2193 +#define MX28_PAD_SSP3_MISO__GPIO_2_26 0x21a3 +#define MX28_PAD_SSP3_SS0__GPIO_2_27 0x21b3 +#define MX28_PAD_AUART0_RX__GPIO_3_0 0x3003 +#define MX28_PAD_AUART0_TX__GPIO_3_1 0x3013 +#define MX28_PAD_AUART0_CTS__GPIO_3_2 0x3023 +#define MX28_PAD_AUART0_RTS__GPIO_3_3 0x3033 +#define MX28_PAD_AUART1_RX__GPIO_3_4 0x3043 +#define MX28_PAD_AUART1_TX__GPIO_3_5 0x3053 +#define MX28_PAD_AUART1_CTS__GPIO_3_6 0x3063 +#define MX28_PAD_AUART1_RTS__GPIO_3_7 0x3073 +#define MX28_PAD_AUART2_RX__GPIO_3_8 0x3083 +#define MX28_PAD_AUART2_TX__GPIO_3_9 0x3093 +#define MX28_PAD_AUART2_CTS__GPIO_3_10 0x30a3 +#define MX28_PAD_AUART2_RTS__GPIO_3_11 0x30b3 +#define MX28_PAD_AUART3_RX__GPIO_3_12 0x30c3 +#define MX28_PAD_AUART3_TX__GPIO_3_13 0x30d3 +#define MX28_PAD_AUART3_CTS__GPIO_3_14 0x30e3 +#define MX28_PAD_AUART3_RTS__GPIO_3_15 0x30f3 +#define MX28_PAD_PWM0__GPIO_3_16 0x3103 +#define MX28_PAD_PWM1__GPIO_3_17 0x3113 +#define MX28_PAD_PWM2__GPIO_3_18 0x3123 +#define MX28_PAD_SAIF0_MCLK__GPIO_3_20 0x3143 +#define MX28_PAD_SAIF0_LRCLK__GPIO_3_21 0x3153 +#define MX28_PAD_SAIF0_BITCLK__GPIO_3_22 0x3163 +#define MX28_PAD_SAIF0_SDATA0__GPIO_3_23 0x3173 +#define MX28_PAD_I2C0_SCL__GPIO_3_24 0x3183 +#define MX28_PAD_I2C0_SDA__GPIO_3_25 0x3193 +#define MX28_PAD_SAIF1_SDATA0__GPIO_3_26 0x31a3 +#define MX28_PAD_SPDIF__GPIO_3_27 0x31b3 +#define MX28_PAD_PWM3__GPIO_3_28 0x31c3 +#define MX28_PAD_PWM4__GPIO_3_29 0x31d3 +#define MX28_PAD_LCD_RESET__GPIO_3_30 0x31e3 +#define MX28_PAD_ENET0_MDC__GPIO_4_0 0x4003 +#define MX28_PAD_ENET0_MDIO__GPIO_4_1 0x4013 +#define MX28_PAD_ENET0_RX_EN__GPIO_4_2 0x4023 +#define MX28_PAD_ENET0_RXD0__GPIO_4_3 0x4033 +#define MX28_PAD_ENET0_RXD1__GPIO_4_4 0x4043 +#define MX28_PAD_ENET0_TX_CLK__GPIO_4_5 0x4053 +#define MX28_PAD_ENET0_TX_EN__GPIO_4_6 0x4063 +#define MX28_PAD_ENET0_TXD0__GPIO_4_7 0x4073 +#define MX28_PAD_ENET0_TXD1__GPIO_4_8 0x4083 +#define MX28_PAD_ENET0_RXD2__GPIO_4_9 0x4093 +#define MX28_PAD_ENET0_RXD3__GPIO_4_10 0x40a3 +#define MX28_PAD_ENET0_TXD2__GPIO_4_11 0x40b3 +#define MX28_PAD_ENET0_TXD3__GPIO_4_12 0x40c3 +#define MX28_PAD_ENET0_RX_CLK__GPIO_4_13 0x40d3 +#define MX28_PAD_ENET0_COL__GPIO_4_14 0x40e3 +#define MX28_PAD_ENET0_CRS__GPIO_4_15 0x40f3 +#define MX28_PAD_ENET_CLK__GPIO_4_16 0x4103 +#define MX28_PAD_JTAG_RTCK__GPIO_4_20 0x4143 + +#endif /* __DT_BINDINGS_MX28_PINCTRL_H__ */ diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts index 6c6a544..4870f07 100644 --- a/arch/arm/boot/dts/imx28-sps1.dts +++ b/arch/arm/boot/dts/imx28-sps1.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "SchulerControl GmbH, SC SPS 1"; @@ -29,13 +29,13 @@ hog_pins_a: hog-gpios@0 { reg = <0>; fsl,pinmux-ids = < - 0x0003 /* MX28_PAD_GPMI_D00__GPIO_0_0 */ - 0x0033 /* MX28_PAD_GPMI_D03__GPIO_0_3 */ - 0x0063 /* MX28_PAD_GPMI_D06__GPIO_0_6 */ + MX28_PAD_GPMI_D00__GPIO_0_0 + MX28_PAD_GPMI_D03__GPIO_0_3 + MX28_PAD_GPMI_D06__GPIO_0_6 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts index 37be532..be5a055 100644 --- a/arch/arm/boot/dts/imx28-tx28.dts +++ b/arch/arm/boot/dts/imx28-tx28.dts @@ -1,106 +1,139 @@ +/* + * Copyright 2012 Shawn Guo <shawn.guo@linaro.org> + * Copyright 2013 Lothar Waßmann <LW@KARO-electronics.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Ka-Ro electronics TX28 module"; compatible = "karo,tx28", "fsl,imx28"; + aliases { + can0 = &can0; + can1 = &can1; + display = &display; + ds1339 = &ds1339; + gpio5 = &gpio5; + lcdif = &lcdif; + lcdif_23bit_pins = &tx28_lcdif_23bit_pins; + lcdif_24bit_pins = &lcdif_24bit_pins_a; + stk5led = &user_led; + usbotg = &usb0; + }; + memory { - reg = <0x40000000 0x08000000>; - }; - - apb@80000000 { - apbh@80000000 { - ssp0: ssp@80010000 { - compatible = "fsl,imx28-mmc"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_4bit_pins_a - &mmc0_cd_cfg - &mmc0_sck_cfg>; - bus-width = <4>; - status = "okay"; - }; + reg = <0 0>; /* will be filled in by U-Boot */ + }; - pinctrl@80018000 { - pinctrl-names = "default"; - pinctrl-0 = <&hog_pins_a>; - - hog_pins_a: hog@0 { - reg = <0>; - fsl,pinmux-ids = < - 0x40a3 /* MX28_PAD_ENET0_RXD3__GPIO_4_10 */ - >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; - }; - - mac0_pins_gpio: mac0-gpio-mode@0 { - reg = <0>; - fsl,pinmux-ids = < - 0x4003 /* MX28_PAD_ENET0_MDC__GPIO_4_0 */ - 0x4013 /* MX28_PAD_ENET0_MDIO__GPIO_4_1 */ - 0x4023 /* MX28_PAD_ENET0_RX_EN__GPIO_4_2 */ - 0x4033 /* MX28_PAD_ENET0_RXD0__GPIO_4_3 */ - 0x4043 /* MX28_PAD_ENET0_RXD1__GPIO_4_4 */ - 0x4063 /* MX28_PAD_ENET0_TX_EN__GPIO_4_6 */ - 0x4073 /* MX28_PAD_ENET0_TXD0__GPIO_4_7 */ - 0x4083 /* MX28_PAD_ENET0_TXD1__GPIO_4_8 */ - 0x4103 /* MX28_PAD_ENET_CLK__GPIO_4_16 */ - >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; - }; - }; + onewire { + compatible = "w1-gpio"; + gpios = <&gpio2 7 0>; + status = "disabled"; + }; + + regulators { + compatible = "simple-bus"; + + reg_usb0_vbus: usb0_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio0 18 0>; + enable-active-high; }; - apbx@80040000 { - i2c0: i2c@80058000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; + reg_usb1_vbus: usb1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 27 0>; + enable-active-high; + }; - ds1339: rtc@68 { - compatible = "mxim,ds1339"; - reg = <0x68>; - }; - }; + reg_2p5v: 2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; - pwm: pwm@80064000 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_pins_a>; - status = "okay"; - }; + reg_3p3v: 3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; - duart: serial@80074000 { - pinctrl-names = "default"; - pinctrl-0 = <&duart_4pins_a>; - status = "okay"; - }; + reg_can_xcvr: can-xcvr { + compatible = "regulator-fixed"; + regulator-name = "CAN XCVR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 0 0>; + enable-active-low; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_flexcan_xcvr_pins>; + }; - auart1: serial@8006c000 { - pinctrl-names = "default"; - pinctrl-0 = <&auart1_pins_a>; - status = "okay"; - }; + reg_lcd: lcd-power { + compatible = "regulator-fixed"; + regulator-name = "LCD POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 31 0>; + enable-active-high; + }; + + reg_lcd_reset: lcd-reset { + compatible = "regulator-fixed"; + regulator-name = "LCD RESET"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 30 0>; + startup-delay-us = <300000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; }; }; - ahb@80080000 { - mac0: ethernet@800f0000 { - phy-mode = "rmii"; - pinctrl-names = "default", "gpio_mode"; - pinctrl-0 = <&mac0_pins_a>; - pinctrl-1 = <&mac0_pins_gpio>; - status = "okay"; + clocks { + #address-cells = <1>; + #size-cells = <0>; + mclk: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <27000000>; }; }; + sound { + compatible = "fsl,imx28-tx28-sgtl5000", + "fsl,mxs-audio-sgtl5000"; + model = "imx28-tx28-sgtl5000"; + saif-controllers = <&saif0 &saif1>; + audio-codec = <&sgtl5000>; + }; + leds { compatible = "gpio-leds"; - user { + user_led: user { label = "Heartbeat"; gpios = <&gpio4 10 0>; linux,default-trigger = "heartbeat"; @@ -109,8 +142,512 @@ backlight { compatible = "pwm-backlight"; - pwms = <&pwm 0 5000000>; - brightness-levels = <0 4 8 16 32 64 128 255>; - default-brightness-level = <6>; + pwms = <&pwm 0 500000>; + /* + * a silly way to create a 1:1 relationship between the + * PWM value and the actual duty cycle + */ + brightness-levels = < 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100>; + default-brightness-level = <50>; + }; + + matrix_keypad: matrix-keypad@0 { + compatible = "gpio-matrix-keypad"; + col-gpios = < + &gpio5 0 0 + &gpio5 1 0 + &gpio5 2 0 + &gpio5 3 0 + >; + row-gpios = < + &gpio5 4 0 + &gpio5 5 0 + &gpio5 6 0 + &gpio5 7 0 + >; + /* sample keymap */ + linux,keymap = < + 0x00000074 /* row 0, col 0, KEY_POWER */ + 0x00010052 /* row 0, col 1, KEY_KP0 */ + 0x0002004f /* row 0, col 2, KEY_KP1 */ + 0x00030050 /* row 0, col 3, KEY_KP2 */ + 0x01000051 /* row 1, col 0, KEY_KP3 */ + 0x0101004b /* row 1, col 1, KEY_KP4 */ + 0x0102004c /* row 1, col 2, KEY_KP5 */ + 0x0103004d /* row 1, col 3, KEY_KP6 */ + 0x02000047 /* row 2, col 0, KEY_KP7 */ + 0x02010048 /* row 2, col 1, KEY_KP8 */ + 0x02020049 /* row 2, col 2, KEY_KP9 */ + >; + gpio-activelow; + linux,wakeup; + debounce-delay-ms = <100>; + col-scan-delay-us = <5000>; + linux,no-autorepeat; + }; +}; + +/* 2nd TX-Std UART - (A)UART1 */ +&auart1 { + pinctrl-names = "default"; + pinctrl-0 = <&auart1_pins_a>; + status = "okay"; +}; + +/* 3rd TX-Std UART - (A)UART3 */ +&auart3 { + pinctrl-names = "default"; + pinctrl-0 = <&auart3_pins_a>; + status = "okay"; +}; + +&can0 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&can1_pins_a>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&digctl { + status = "okay"; +}; + +/* 1st TX-Std UART - (D)UART */ +&duart { + pinctrl-names = "default"; + pinctrl-0 = <&duart_4pins_a>; + status = "okay"; +}; + +&gpmi { + pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>; + nand-on-flash-bbt; + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + clock-frequency = <400000>; + status = "okay"; + + sgtl5000: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + clocks = <&mclk>; + }; + + gpio5: pca953x@20 { + compatible = "nxp,pca9554"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_pca9554_pins>; + interrupt-parent = <&gpio3>; + interrupts = <28 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_edt_ft5x06_pins>; + interrupt-parent = <&gpio2>; + interrupts = <5 0>; + reset-gpios = <&gpio2 6 1>; + wake-gpios = <&gpio4 9 0>; + }; + + touchscreen: tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_tsc2007_pins>; + interrupt-parent = <&gpio3>; + interrupts = <20 0>; + pendown-gpio = <&gpio3 20 1>; + ti,x-plate-ohms = /bits/ 16 <660>; + }; + + ds1339: rtc@68 { + compatible = "mxim,ds1339"; + reg = <0x68>; + }; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a &lcdif_sync_pins_a &tx28_lcdif_ctrl_pins>; + lcd-supply = <®_lcd>; + display = <&display>; + status = "okay"; + + display: display@0 { + bits-per-pixel = <32>; + bus-width = <24>; + display-timings { + native-mode = <&timing5>; + timing0: timing0 { + panel-name = "VGA"; + clock-frequency = <25175000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing1: timing1 { + panel-name = "ETV570"; + clock-frequency = <25175000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing2: timing2 { + panel-name = "ET0350"; + clock-frequency = <6500000>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing3: timing3 { + panel-name = "ET0430"; + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing4: timing4 { + panel-name = "ET0500", "ET0700"; + clock-frequency = <33260000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing5: timing5 { + panel-name = "ETQ570"; + clock-frequency = <6400000>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; +}; + +&lradc { + fsl,lradc-touchscreen-wires = <4>; + status = "okay"; +}; + +&mac0 { + phy-mode = "rmii"; + pinctrl-names = "default", "gpio_mode"; + pinctrl-0 = <&mac0_pins_a>; + pinctrl-1 = <&tx28_mac0_pins_gpio>; + status = "okay"; +}; + +&mac1 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac1_pins_a>; + /* not enabled by default */ +}; + +&mxs_rtc { + status = "okay"; +}; + +&ocotp { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_RXD3__GPIO_4_10 /* module LED */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_edt_ft5x06_pins: tx28-edt-ft5x06-pins { + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA6__GPIO_2_6 /* RESET */ + MX28_PAD_SSP0_DATA5__GPIO_2_5 /* IRQ */ + MX28_PAD_ENET0_RXD2__GPIO_4_9 /* WAKE */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_flexcan_xcvr_pins: tx28-flexcan-xcvr-pins { + fsl,pinmux-ids = < + MX28_PAD_LCD_D00__GPIO_1_0 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_lcdif_23bit_pins: tx28-lcdif-23bit { + fsl,pinmux-ids = < + /* LCD_D00 may be used as Flexcan Transceiver Enable on STK5-V5 */ + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 + MX28_PAD_LCD_D18__LCD_D18 + MX28_PAD_LCD_D19__LCD_D19 + MX28_PAD_LCD_D20__LCD_D20 + MX28_PAD_LCD_D21__LCD_D21 + MX28_PAD_LCD_D22__LCD_D22 + MX28_PAD_LCD_D23__LCD_D23 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_lcdif_ctrl_pins: tx28-lcdif-ctrl { + fsl,pinmux-ids = < + MX28_PAD_LCD_ENABLE__GPIO_1_31 /* Enable */ + MX28_PAD_LCD_RESET__GPIO_3_30 /* Reset */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_mac0_pins_gpio: tx28-mac0-gpio-pins { + fsl,pinmux-ids = < + MX28_PAD_ENET0_MDC__GPIO_4_0 + MX28_PAD_ENET0_MDIO__GPIO_4_1 + MX28_PAD_ENET0_RX_EN__GPIO_4_2 + MX28_PAD_ENET0_RXD0__GPIO_4_3 + MX28_PAD_ENET0_RXD1__GPIO_4_4 + MX28_PAD_ENET0_TX_EN__GPIO_4_6 + MX28_PAD_ENET0_TXD0__GPIO_4_7 + MX28_PAD_ENET0_TXD1__GPIO_4_8 + MX28_PAD_ENET_CLK__GPIO_4_16 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_pca9554_pins: tx28-pca9554-pins { + fsl,pinmux-ids = < + MX28_PAD_PWM3__GPIO_3_28 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_tsc2007_pins: tx28-tsc2007-pins { + fsl,pinmux-ids = < + MX28_PAD_SAIF0_MCLK__GPIO_3_20 /* TSC2007 IRQ */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + + tx28_usbphy0_pins: tx28-usbphy0-pins { + fsl,pinmux-ids = < + MX28_PAD_GPMI_CE2N__GPIO_0_18 /* USBOTG_VBUSEN */ + MX28_PAD_GPMI_CE3N__GPIO_0_19 /* USBOTH_OC */ + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_usbphy1_pins: tx28-usbphy1-pins { + fsl,pinmux-ids = < + MX28_PAD_SPDIF__GPIO_3_27 /* USBH_VBUSEN */ + MX28_PAD_JTAG_RTCK__GPIO_4_20 /* USBH_OC */ + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; +}; + +&saif0 { + pinctrl-names = "default"; + pinctrl-0 = <&saif0_pins_b>; + fsl,saif-master; + status = "okay"; +}; + +&saif1 { + pinctrl-names = "default"; + pinctrl-0 = <&saif1_pins_a>; + status = "okay"; +}; + +&ssp0 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default", "special"; + pinctrl-0 = <&mmc0_4bit_pins_a + &mmc0_cd_cfg + &mmc0_sck_cfg>; + bus-width = <4>; + status = "okay"; +}; + +&ssp3 { + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins_a>; + clock-frequency = <57600000>; + status = "okay"; + + spidev0: spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <57600000>; + }; + + spidev1: spi@1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <57600000>; }; }; + +&usb0 { + vbus-supply = <®_usb0_vbus>; + disable-over-current; + dr_mode = "peripheral"; + status = "okay"; +}; + +&usb1 { + vbus-supply = <®_usb1_vbus>; + disable-over-current; + dr_mode = "host"; + status = "okay"; +}; + +&usbphy0 { + pinctrl-names = "default"; + pinctrl-0 = <&tx28_usbphy0_pins>; + phy_type = "utmi"; + status = "okay"; +}; + +&usbphy1 { + pinctrl-names = "default"; + pinctrl-0 = <&tx28_usbphy1_pins>; + phy_type = "utmi"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 175deef..cda19c8 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -9,7 +9,8 @@ * http://www.gnu.org/copyleft/gpl.html */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" +#include "imx28-pinfunc.h" / { interrupt-parent = <&icoll>; @@ -207,538 +208,579 @@ duart_pins_a: duart@0 { reg = <0>; fsl,pinmux-ids = < - 0x3102 /* MX28_PAD_PWM0__DUART_RX */ - 0x3112 /* MX28_PAD_PWM1__DUART_TX */ + MX28_PAD_PWM0__DUART_RX + MX28_PAD_PWM1__DUART_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; duart_pins_b: duart@1 { reg = <1>; fsl,pinmux-ids = < - 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */ - 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */ + MX28_PAD_AUART0_CTS__DUART_RX + MX28_PAD_AUART0_RTS__DUART_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; duart_4pins_a: duart-4pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */ - 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */ - 0x3002 /* MX28_PAD_AUART0_RX__DUART_CTS */ - 0x3012 /* MX28_PAD_AUART0_TX__DUART_RTS */ + MX28_PAD_AUART0_CTS__DUART_RX + MX28_PAD_AUART0_RTS__DUART_TX + MX28_PAD_AUART0_RX__DUART_CTS + MX28_PAD_AUART0_TX__DUART_RTS >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; gpmi_pins_a: gpmi-nand@0 { reg = <0>; fsl,pinmux-ids = < - 0x0000 /* MX28_PAD_GPMI_D00__GPMI_D0 */ - 0x0010 /* MX28_PAD_GPMI_D01__GPMI_D1 */ - 0x0020 /* MX28_PAD_GPMI_D02__GPMI_D2 */ - 0x0030 /* MX28_PAD_GPMI_D03__GPMI_D3 */ - 0x0040 /* MX28_PAD_GPMI_D04__GPMI_D4 */ - 0x0050 /* MX28_PAD_GPMI_D05__GPMI_D5 */ - 0x0060 /* MX28_PAD_GPMI_D06__GPMI_D6 */ - 0x0070 /* MX28_PAD_GPMI_D07__GPMI_D7 */ - 0x0100 /* MX28_PAD_GPMI_CE0N__GPMI_CE0N */ - 0x0140 /* MX28_PAD_GPMI_RDY0__GPMI_READY0 */ - 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */ - 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */ - 0x01a0 /* MX28_PAD_GPMI_ALE__GPMI_ALE */ - 0x01b0 /* MX28_PAD_GPMI_CLE__GPMI_CLE */ - 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */ + MX28_PAD_GPMI_D00__GPMI_D0 + MX28_PAD_GPMI_D01__GPMI_D1 + MX28_PAD_GPMI_D02__GPMI_D2 + MX28_PAD_GPMI_D03__GPMI_D3 + MX28_PAD_GPMI_D04__GPMI_D4 + MX28_PAD_GPMI_D05__GPMI_D5 + MX28_PAD_GPMI_D06__GPMI_D6 + MX28_PAD_GPMI_D07__GPMI_D7 + MX28_PAD_GPMI_CE0N__GPMI_CE0N + MX28_PAD_GPMI_RDY0__GPMI_READY0 + MX28_PAD_GPMI_RDN__GPMI_RDN + MX28_PAD_GPMI_WRN__GPMI_WRN + MX28_PAD_GPMI_ALE__GPMI_ALE + MX28_PAD_GPMI_CLE__GPMI_CLE + MX28_PAD_GPMI_RESETN__GPMI_RESETN >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; gpmi_status_cfg: gpmi-status-cfg { fsl,pinmux-ids = < - 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */ - 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */ - 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */ + MX28_PAD_GPMI_RDN__GPMI_RDN + MX28_PAD_GPMI_WRN__GPMI_WRN + MX28_PAD_GPMI_RESETN__GPMI_RESETN >; - fsl,drive-strength = <2>; + fsl,drive-strength = <MXS_DRIVE_12mA>; }; auart0_pins_a: auart0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */ - 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */ - 0x3020 /* MX28_PAD_AUART0_CTS__AUART0_CTS */ - 0x3030 /* MX28_PAD_AUART0_RTS__AUART0_RTS */ + MX28_PAD_AUART0_RX__AUART0_RX + MX28_PAD_AUART0_TX__AUART0_TX + MX28_PAD_AUART0_CTS__AUART0_CTS + MX28_PAD_AUART0_RTS__AUART0_RTS >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart0_2pins_a: auart0-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */ - 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */ + MX28_PAD_AUART0_RX__AUART0_RX + MX28_PAD_AUART0_TX__AUART0_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart1_pins_a: auart1@0 { reg = <0>; fsl,pinmux-ids = < - 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */ - 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */ - 0x3060 /* MX28_PAD_AUART1_CTS__AUART1_CTS */ - 0x3070 /* MX28_PAD_AUART1_RTS__AUART1_RTS */ + MX28_PAD_AUART1_RX__AUART1_RX + MX28_PAD_AUART1_TX__AUART1_TX + MX28_PAD_AUART1_CTS__AUART1_CTS + MX28_PAD_AUART1_RTS__AUART1_RTS >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart1_2pins_a: auart1-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */ - 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */ + MX28_PAD_AUART1_RX__AUART1_RX + MX28_PAD_AUART1_TX__AUART1_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart2_2pins_a: auart2-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x2101 /* MX28_PAD_SSP2_SCK__AUART2_RX */ - 0x2111 /* MX28_PAD_SSP2_MOSI__AUART2_TX */ + MX28_PAD_SSP2_SCK__AUART2_RX + MX28_PAD_SSP2_MOSI__AUART2_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart2_2pins_b: auart2-2pins@1 { reg = <1>; fsl,pinmux-ids = < - 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */ - 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */ + MX28_PAD_AUART2_RX__AUART2_RX + MX28_PAD_AUART2_TX__AUART2_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart3_pins_a: auart3@0 { reg = <0>; fsl,pinmux-ids = < - 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */ - 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */ - 0x30e0 /* MX28_PAD_AUART3_CTS__AUART3_CTS */ - 0x30f0 /* MX28_PAD_AUART3_RTS__AUART3_RTS */ + MX28_PAD_AUART3_RX__AUART3_RX + MX28_PAD_AUART3_TX__AUART3_TX + MX28_PAD_AUART3_CTS__AUART3_CTS + MX28_PAD_AUART3_RTS__AUART3_RTS >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart3_2pins_a: auart3-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x2121 /* MX28_PAD_SSP2_MISO__AUART3_RX */ - 0x2131 /* MX28_PAD_SSP2_SS0__AUART3_TX */ + MX28_PAD_SSP2_MISO__AUART3_RX + MX28_PAD_SSP2_SS0__AUART3_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart3_2pins_b: auart3-2pins@1 { reg = <1>; fsl,pinmux-ids = < - 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */ - 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */ + MX28_PAD_AUART3_RX__AUART3_RX + MX28_PAD_AUART3_TX__AUART3_TX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; auart4_2pins_a: auart4@0 { reg = <0>; fsl,pinmux-ids = < - 0x2181 /* MX28_PAD_SSP3_SCK__AUART4_TX */ - 0x2191 /* MX28_PAD_SSP3_MOSI__AUART4_RX */ + MX28_PAD_SSP3_SCK__AUART4_TX + MX28_PAD_SSP3_MOSI__AUART4_RX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; mac0_pins_a: mac0@0 { reg = <0>; fsl,pinmux-ids = < - 0x4000 /* MX28_PAD_ENET0_MDC__ENET0_MDC */ - 0x4010 /* MX28_PAD_ENET0_MDIO__ENET0_MDIO */ - 0x4020 /* MX28_PAD_ENET0_RX_EN__ENET0_RX_EN */ - 0x4030 /* MX28_PAD_ENET0_RXD0__ENET0_RXD0 */ - 0x4040 /* MX28_PAD_ENET0_RXD1__ENET0_RXD1 */ - 0x4060 /* MX28_PAD_ENET0_TX_EN__ENET0_TX_EN */ - 0x4070 /* MX28_PAD_ENET0_TXD0__ENET0_TXD0 */ - 0x4080 /* MX28_PAD_ENET0_TXD1__ENET0_TXD1 */ - 0x4100 /* MX28_PAD_ENET_CLK__CLKCTRL_ENET */ + MX28_PAD_ENET0_MDC__ENET0_MDC + MX28_PAD_ENET0_MDIO__ENET0_MDIO + MX28_PAD_ENET0_RX_EN__ENET0_RX_EN + MX28_PAD_ENET0_RXD0__ENET0_RXD0 + MX28_PAD_ENET0_RXD1__ENET0_RXD1 + MX28_PAD_ENET0_TX_EN__ENET0_TX_EN + MX28_PAD_ENET0_TXD0__ENET0_TXD0 + MX28_PAD_ENET0_TXD1__ENET0_TXD1 + MX28_PAD_ENET_CLK__CLKCTRL_ENET >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mac1_pins_a: mac1@0 { reg = <0>; fsl,pinmux-ids = < - 0x40f1 /* MX28_PAD_ENET0_CRS__ENET1_RX_EN */ - 0x4091 /* MX28_PAD_ENET0_RXD2__ENET1_RXD0 */ - 0x40a1 /* MX28_PAD_ENET0_RXD3__ENET1_RXD1 */ - 0x40e1 /* MX28_PAD_ENET0_COL__ENET1_TX_EN */ - 0x40b1 /* MX28_PAD_ENET0_TXD2__ENET1_TXD0 */ - 0x40c1 /* MX28_PAD_ENET0_TXD3__ENET1_TXD1 */ + MX28_PAD_ENET0_CRS__ENET1_RX_EN + MX28_PAD_ENET0_RXD2__ENET1_RXD0 + MX28_PAD_ENET0_RXD3__ENET1_RXD1 + MX28_PAD_ENET0_COL__ENET1_TX_EN + MX28_PAD_ENET0_TXD2__ENET1_TXD0 + MX28_PAD_ENET0_TXD3__ENET1_TXD1 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mmc0_8bit_pins_a: mmc0-8bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */ - 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */ - 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */ - 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */ - 0x2040 /* MX28_PAD_SSP0_DATA4__SSP0_D4 */ - 0x2050 /* MX28_PAD_SSP0_DATA5__SSP0_D5 */ - 0x2060 /* MX28_PAD_SSP0_DATA6__SSP0_D6 */ - 0x2070 /* MX28_PAD_SSP0_DATA7__SSP0_D7 */ - 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */ - 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ - 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + MX28_PAD_SSP0_DATA0__SSP0_D0 + MX28_PAD_SSP0_DATA1__SSP0_D1 + MX28_PAD_SSP0_DATA2__SSP0_D2 + MX28_PAD_SSP0_DATA3__SSP0_D3 + MX28_PAD_SSP0_DATA4__SSP0_D4 + MX28_PAD_SSP0_DATA5__SSP0_D5 + MX28_PAD_SSP0_DATA6__SSP0_D6 + MX28_PAD_SSP0_DATA7__SSP0_D7 + MX28_PAD_SSP0_CMD__SSP0_CMD + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + MX28_PAD_SSP0_SCK__SSP0_SCK >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mmc0_4bit_pins_a: mmc0-4bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */ - 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */ - 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */ - 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */ - 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */ - 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ - 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + MX28_PAD_SSP0_DATA0__SSP0_D0 + MX28_PAD_SSP0_DATA1__SSP0_D1 + MX28_PAD_SSP0_DATA2__SSP0_D2 + MX28_PAD_SSP0_DATA3__SSP0_D3 + MX28_PAD_SSP0_CMD__SSP0_CMD + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + MX28_PAD_SSP0_SCK__SSP0_SCK >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; mmc0_cd_cfg: mmc0-cd-cfg { fsl,pinmux-ids = < - 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT >; - fsl,pull-up = <0>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; mmc0_sck_cfg: mmc0-sck-cfg { fsl,pinmux-ids = < - 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + MX28_PAD_SSP0_SCK__SSP0_SCK >; - fsl,drive-strength = <2>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc2_4bit_pins_a: mmc2-4bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA4__SSP2_D0 + MX28_PAD_SSP1_SCK__SSP2_D1 + MX28_PAD_SSP1_CMD__SSP2_D2 + MX28_PAD_SSP0_DATA5__SSP2_D3 + MX28_PAD_SSP0_DATA6__SSP2_CMD + MX28_PAD_AUART1_RX__SSP2_CARD_DETECT + MX28_PAD_SSP0_DATA7__SSP2_SCK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc2_cd_cfg: mmc2-cd-cfg { + fsl,pinmux-ids = < + MX28_PAD_AUART1_RX__SSP2_CARD_DETECT + >; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc2_sck_cfg: mmc2-sck-cfg { + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA7__SSP2_SCK + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; i2c0_pins_a: i2c0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3180 /* MX28_PAD_I2C0_SCL__I2C0_SCL */ - 0x3190 /* MX28_PAD_I2C0_SDA__I2C0_SDA */ + MX28_PAD_I2C0_SCL__I2C0_SCL + MX28_PAD_I2C0_SDA__I2C0_SDA >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; i2c0_pins_b: i2c0@1 { reg = <1>; fsl,pinmux-ids = < - 0x3001 /* MX28_PAD_AUART0_RX__I2C0_SCL */ - 0x3011 /* MX28_PAD_AUART0_TX__I2C0_SDA */ + MX28_PAD_AUART0_RX__I2C0_SCL + MX28_PAD_AUART0_TX__I2C0_SDA >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; i2c1_pins_a: i2c1@0 { reg = <0>; fsl,pinmux-ids = < - 0x3101 /* MX28_PAD_PWM0__I2C1_SCL */ - 0x3111 /* MX28_PAD_PWM1__I2C1_SDA */ + MX28_PAD_PWM0__I2C1_SCL + MX28_PAD_PWM1__I2C1_SDA >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; saif0_pins_a: saif0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3140 /* MX28_PAD_SAIF0_MCLK__SAIF0_MCLK */ - 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */ - 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */ - 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */ + MX28_PAD_SAIF0_MCLK__SAIF0_MCLK + MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK + MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK + MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 >; - fsl,drive-strength = <2>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; saif0_pins_b: saif0@1 { reg = <1>; fsl,pinmux-ids = < - 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */ - 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */ - 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */ + MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK + MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK + MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 >; - fsl,drive-strength = <2>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; saif1_pins_a: saif1@0 { reg = <0>; fsl,pinmux-ids = < - 0x31a0 /* MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 */ + MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 >; - fsl,drive-strength = <2>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; pwm0_pins_a: pwm0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3100 /* MX28_PAD_PWM0__PWM_0 */ + MX28_PAD_PWM0__PWM_0 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; pwm2_pins_a: pwm2@0 { reg = <0>; fsl,pinmux-ids = < - 0x3120 /* MX28_PAD_PWM2__PWM_2 */ + MX28_PAD_PWM2__PWM_2 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; pwm3_pins_a: pwm3@0 { reg = <0>; fsl,pinmux-ids = < - 0x31c0 /* MX28_PAD_PWM3__PWM_3 */ + MX28_PAD_PWM3__PWM_3 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; pwm3_pins_b: pwm3@1 { reg = <1>; fsl,pinmux-ids = < - 0x3141 /* MX28_PAD_SAIF0_MCLK__PWM3 */ + MX28_PAD_SAIF0_MCLK__PWM_3 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; pwm4_pins_a: pwm4@0 { reg = <0>; fsl,pinmux-ids = < - 0x31d0 /* MX28_PAD_PWM4__PWM_4 */ + MX28_PAD_PWM4__PWM_4 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_24bit_pins_a: lcdif-24bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ - 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */ - 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */ - 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */ - 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */ - 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */ - 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 + MX28_PAD_LCD_D18__LCD_D18 + MX28_PAD_LCD_D19__LCD_D19 + MX28_PAD_LCD_D20__LCD_D20 + MX28_PAD_LCD_D21__LCD_D21 + MX28_PAD_LCD_D22__LCD_D22 + MX28_PAD_LCD_D23__LCD_D23 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_16bit_pins_a: lcdif-16bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; lcdif_sync_pins_a: lcdif-sync@0 { reg = <0>; fsl,pinmux-ids = < - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; can0_pins_a: can0@0 { reg = <0>; fsl,pinmux-ids = < - 0x0161 /* MX28_PAD_GPMI_RDY2__CAN0_TX */ - 0x0171 /* MX28_PAD_GPMI_RDY3__CAN0_RX */ + MX28_PAD_GPMI_RDY2__CAN0_TX + MX28_PAD_GPMI_RDY3__CAN0_RX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; can1_pins_a: can1@0 { reg = <0>; fsl,pinmux-ids = < - 0x0121 /* MX28_PAD_GPMI_CE2N__CAN1_TX */ - 0x0131 /* MX28_PAD_GPMI_CE3N__CAN1_RX */ + MX28_PAD_GPMI_CE2N__CAN1_TX + MX28_PAD_GPMI_CE3N__CAN1_RX >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; spi2_pins_a: spi2@0 { reg = <0>; fsl,pinmux-ids = < - 0x2100 /* MX28_PAD_SSP2_SCK__SSP2_SCK */ - 0x2110 /* MX28_PAD_SSP2_MOSI__SSP2_CMD */ - 0x2120 /* MX28_PAD_SSP2_MISO__SSP2_D0 */ - 0x2130 /* MX28_PAD_SSP2_SS0__SSP2_D3 */ + MX28_PAD_SSP2_SCK__SSP2_SCK + MX28_PAD_SSP2_MOSI__SSP2_CMD + MX28_PAD_SSP2_MISO__SSP2_D0 + MX28_PAD_SSP2_SS0__SSP2_D3 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <1>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; spi3_pins_a: spi3@0 { reg = <0>; fsl,pinmux-ids = < - 0x3082 /* MX28_PAD_AUART2_RX__SSP3_D4 */ - 0x3092 /* MX28_PAD_AUART2_TX__SSP3_D5 */ - 0x2180 /* MX28_PAD_SSP3_SCK__SSP3_SCK */ - 0x2190 /* MX28_PAD_SSP3_MOSI__SSP3_CMD */ - 0x21A0 /* MX28_PAD_SSP3_MISO__SSP3_D0 */ - 0x21B0 /* MX28_PAD_SSP3_SS0__SSP3_D3 */ + MX28_PAD_AUART2_RX__SSP3_D4 + MX28_PAD_AUART2_TX__SSP3_D5 + MX28_PAD_SSP3_SCK__SSP3_SCK + MX28_PAD_SSP3_MOSI__SSP3_CMD + MX28_PAD_SSP3_MISO__SSP3_D0 + MX28_PAD_SSP3_SS0__SSP3_D3 >; - fsl,drive-strength = <1>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; usbphy0_pins_a: usbphy0@0 { reg = <0>; fsl,pinmux-ids = < - 0x2152 /* MX28_PAD_SSP2_SS2__USB0_OVERCURRENT */ + MX28_PAD_SSP2_SS2__USB0_OVERCURRENT >; - fsl,drive-strength = <2>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; usbphy0_pins_b: usbphy0@1 { reg = <1>; fsl,pinmux-ids = < - 0x3061 /* MX28_PAD_AUART1_CTS__USB0_OVERCURRENT */ + MX28_PAD_AUART1_CTS__USB0_OVERCURRENT >; - fsl,drive-strength = <2>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; usbphy1_pins_a: usbphy1@0 { reg = <0>; fsl,pinmux-ids = < - 0x2142 /* MX28_PAD_SSP2_SS1__USB1_OVERCURRENT */ + MX28_PAD_SSP2_SS1__USB1_OVERCURRENT + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + usb0_id_pins_a: usb0id@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_RTS__USB0_ID >; - fsl,drive-strength = <2>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; }; }; diff --git a/arch/arm/boot/dts/imx51-apf51dev.dts b/arch/arm/boot/dts/imx51-apf51dev.dts index 123fe84..5a7f552 100644 --- a/arch/arm/boot/dts/imx51-apf51dev.dts +++ b/arch/arm/boot/dts/imx51-apf51dev.dts @@ -16,6 +16,33 @@ model = "Armadeus Systems APF51Dev docking/development board"; compatible = "armadeus,imx51-apf51dev", "armadeus,imx51-apf51", "fsl,imx51"; + display@di1 { + compatible = "fsl,imx-parallel-display"; + crtcs = <&ipu 0>; + interface-pix-fmt = "bgr666"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu_disp1_1>; + + display-timings { + lw700 { + native-mode; + clock-frequency = <33000033>; + hactive = <800>; + vactive = <480>; + hback-porch = <96>; + hfront-porch = <96>; + vback-porch = <20>; + vfront-porch = <21>; + hsync-len = <64>; + vsync-len = <4>; + hsync-active = <1>; + vsync-active = <1>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + gpio-keys { compatible = "gpio-keys"; diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts index 1d337d9..be1407c 100644 --- a/arch/arm/boot/dts/imx51-babbage.dts +++ b/arch/arm/boot/dts/imx51-babbage.dts @@ -27,6 +27,20 @@ interface-pix-fmt = "rgb24"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ipu_disp1_1>; + display-timings { + native-mode = <&timing0>; + timing0: dvi { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hfront-porch = <40>; + vback-porch = <21>; + vfront-porch = <7>; + hsync-len = <60>; + vsync-len = <10>; + }; + }; }; display@di1 { @@ -35,6 +49,25 @@ interface-pix-fmt = "rgb565"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ipu_disp2_1>; + status = "disabled"; + display-timings { + native-mode = <&timing1>; + timing1: claawvga { + clock-frequency = <27000000>; + hactive = <800>; + vactive = <480>; + hback-porch = <40>; + hfront-porch = <60>; + vback-porch = <10>; + vfront-porch = <10>; + hsync-len = <20>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; }; gpio-keys { @@ -95,7 +128,7 @@ &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_1>; + pinctrl-0 = <&pinctrl_uart3_1 &pinctrl_uart3_rtscts_1>; fsl,uart-has-rtscts; status = "okay"; }; @@ -252,7 +285,7 @@ &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; fsl,uart-has-rtscts; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi index 54cee65..f4dcff3 100644 --- a/arch/arm/boot/dts/imx51.dtsi +++ b/arch/arm/boot/dts/imx51.dtsi @@ -86,6 +86,11 @@ interrupt-parent = <&tzic>; ranges; + iram: iram@1ffe0000 { + compatible = "mmio-sram"; + reg = <0x1ffe0000 0x20000>; + }; + ipu: ipu@40000000 { #crtc-cells = <1>; compatible = "fsl,imx51-ipu"; @@ -374,6 +379,14 @@ clocks = <&clks 107>; }; + owire: owire@83fa4000 { + compatible = "fsl,imx51-owire", "fsl,imx21-owire"; + reg = <0x83fa4000 0x4000>; + interrupts = <88>; + clocks = <&clks 159>; + status = "disabled"; + }; + ecspi2: ecspi@83fac000 { #address-cells = <1>; #size-cells = <0>; @@ -747,6 +760,11 @@ fsl,pins = < MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 + >; + }; + + pinctrl_uart1_rtscts_1: uart1rtscts-1 { + fsl,pins = < MX51_PAD_UART1_RTS__UART1_RTS 0x1c5 MX51_PAD_UART1_CTS__UART1_CTS 0x1c5 >; @@ -767,6 +785,11 @@ fsl,pins = < MX51_PAD_EIM_D25__UART3_RXD 0x1c5 MX51_PAD_EIM_D26__UART3_TXD 0x1c5 + >; + }; + + pinctrl_uart3_rtscts_1: uart3rtscts-1 { + fsl,pins = < MX51_PAD_EIM_D27__UART3_RTS 0x1c5 MX51_PAD_EIM_D24__UART3_CTS 0x1c5 >; diff --git a/arch/arm/boot/dts/imx53-qsb.dts b/arch/arm/boot/dts/imx53-qsb.dts index e97ddae..91a5935 100644 --- a/arch/arm/boot/dts/imx53-qsb.dts +++ b/arch/arm/boot/dts/imx53-qsb.dts @@ -55,19 +55,20 @@ label = "Power Button"; gpios = <&gpio1 8 0>; linux,code = <116>; /* KEY_POWER */ - gpio-key,wakeup; }; volume-up { label = "Volume Up"; gpios = <&gpio2 14 0>; linux,code = <115>; /* KEY_VOLUMEUP */ + gpio-key,wakeup; }; volume-down { label = "Volume Down"; gpios = <&gpio2 15 0>; linux,code = <114>; /* KEY_VOLUMEDOWN */ + gpio-key,wakeup; }; }; @@ -122,7 +123,6 @@ &esdhc1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1_1>; - cd-gpios = <&gpio3 13 0>; status = "okay"; }; @@ -136,6 +136,7 @@ pinctrl-0 = <&pinctrl_esdhc3_1>; cd-gpios = <&gpio3 11 0>; wp-gpios = <&gpio3 12 0>; + bus-width = <8>; status = "okay"; }; @@ -152,7 +153,6 @@ MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000 MX53_PAD_EIM_DA11__GPIO3_11 0x80000000 MX53_PAD_EIM_DA12__GPIO3_12 0x80000000 - MX53_PAD_EIM_DA13__GPIO3_13 0x80000000 MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 MX53_PAD_PATA_DA_2__GPIO7_8 0x80000000 MX53_PAD_GPIO_16__GPIO7_11 0x80000000 @@ -318,5 +318,6 @@ }; &usbotg { - status = "okay"; + dr_mode = "peripheral"; + status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6q-pinfunc.h b/arch/arm/boot/dts/imx6q-pinfunc.h index 9bbe82b..97ed081 100644 --- a/arch/arm/boot/dts/imx6q-pinfunc.h +++ b/arch/arm/boot/dts/imx6q-pinfunc.h @@ -536,7 +536,7 @@ #define MX6QDL_PAD_ENET_REF_CLK__ESAI_RX_FS 0x1d4 0x4e8 0x85c 0x2 0x0 #define MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1d4 0x4e8 0x000 0x5 0x0 #define MX6QDL_PAD_ENET_REF_CLK__SPDIF_SR_CLK 0x1d4 0x4e8 0x000 0x6 0x0 -#define MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1d8 0x4ec 0x000 0x0 0x0 +#define MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1d8 0x4ec 0x004 0x0 0xff0d0100 #define MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1d8 0x4ec 0x000 0x1 0x0 #define MX6QDL_PAD_ENET_RX_ER__ESAI_RX_HF_CLK 0x1d8 0x4ec 0x864 0x2 0x0 #define MX6QDL_PAD_ENET_RX_ER__SPDIF_IN 0x1d8 0x4ec 0x914 0x3 0x1 @@ -654,7 +654,7 @@ #define MX6QDL_PAD_GPIO_1__ESAI_RX_CLK 0x224 0x5f4 0x86c 0x0 0x1 #define MX6QDL_PAD_GPIO_1__WDOG2_B 0x224 0x5f4 0x000 0x1 0x0 #define MX6QDL_PAD_GPIO_1__KEY_ROW5 0x224 0x5f4 0x8f4 0x2 0x0 -#define MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x224 0x5f4 0x000 0x3 0x0 +#define MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x224 0x5f4 0x004 0x3 0xff0d0101 #define MX6QDL_PAD_GPIO_1__PWM2_OUT 0x224 0x5f4 0x000 0x4 0x0 #define MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x224 0x5f4 0x000 0x5 0x0 #define MX6QDL_PAD_GPIO_1__SD1_CD_B 0x224 0x5f4 0x000 0x6 0x0 diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts index 3530280..f004913 100644 --- a/arch/arm/boot/dts/imx6q-sabrelite.dts +++ b/arch/arm/boot/dts/imx6q-sabrelite.dts @@ -65,8 +65,10 @@ }; }; -&sata { +&audmux { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux_1>; }; &ecspi1 { @@ -83,11 +85,29 @@ }; }; -&ssi1 { - fsl,mode = "i2s-slave"; +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_1>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 23 0>; status = "okay"; }; +&i2c1 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1>; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + }; +}; + &iomuxc { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; @@ -103,28 +123,61 @@ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x80000000 MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0 MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x80000000 + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 >; }; }; }; -&usbotg { - vbus-supply = <®_usb_otg_vbus>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbotg_1>; - disable-over-current; +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + display-timings { + native-mode = <&timing0>; + timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hfront-porch = <40>; + vback-porch = <21>; + vfront-porch = <7>; + hsync-len = <60>; + vsync-len = <10>; + }; + }; + }; +}; + +&sata { + status = "okay"; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; status = "okay"; }; +&uart2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_1>; +}; + &usbh1 { status = "okay"; }; -&fec { +&usbotg { + vbus-supply = <®_usb_otg_vbus>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_1>; - phy-mode = "rgmii"; - phy-reset-gpios = <&gpio3 23 0>; + pinctrl-0 = <&pinctrl_usbotg_1>; + disable-over-current; status = "okay"; }; @@ -145,30 +198,3 @@ vmmc-supply = <®_3p3v>; status = "okay"; }; - -&audmux { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_1>; -}; - -&uart2 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_1>; -}; - -&i2c1 { - status = "okay"; - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_1>; - - codec: sgtl5000@0a { - compatible = "fsl,sgtl5000"; - reg = <0x0a>; - clocks = <&clks 201>; - VDDA-supply = <®_2p5v>; - VDDIO-supply = <®_3p3v>; - }; -}; diff --git a/arch/arm/boot/dts/imx6q-udoo.dts b/arch/arm/boot/dts/imx6q-udoo.dts new file mode 100644 index 0000000..6e1ccdc --- /dev/null +++ b/arch/arm/boot/dts/imx6q-udoo.dts @@ -0,0 +1,39 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * Author: Fabio Estevam <fabio.estevam@freescale.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "Udoo i.MX6 Quad Board"; + compatible = "udoo,imx6q-udoo", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x40000000>; + }; +}; + +&sata { + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_1>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3_2>; + non-removable; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index 1cbbc51..ff6f1e8 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -54,6 +54,7 @@ fsl,pins = < MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000 MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x80000000 + MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x17059 >; }; }; @@ -74,8 +75,10 @@ }; &usdhc3 { - pinctrl-names = "default"; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc3_1>; + pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>; cd-gpios = <&gpio6 15 0>; wp-gpios = <&gpio1 13 0>; status = "okay"; diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi index 39eafc2..e75e11b 100644 --- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi @@ -80,6 +80,14 @@ mux-int-port = <2>; mux-ext-port = <3>; }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + status = "okay"; + }; }; &audmux { @@ -108,6 +116,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet_1>; phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 25 0>; status = "okay"; }; @@ -172,6 +181,7 @@ MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x80000000 MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x80000000 >; }; }; @@ -202,6 +212,12 @@ }; }; +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_1>; + status = "okay"; +}; + &ssi2 { fsl,mode = "i2s-slave"; status = "okay"; @@ -229,6 +245,7 @@ &usdhc2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2_1>; + bus-width = <8>; cd-gpios = <&gpio2 2 0>; wp-gpios = <&gpio2 3 0>; status = "okay"; @@ -237,6 +254,7 @@ &usdhc3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc3_1>; + bus-width = <8>; cd-gpios = <&gpio2 0 0>; wp-gpios = <&gpio2 1 0>; status = "okay"; diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi index a55113e..35f5479 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi @@ -43,6 +43,13 @@ mux-int-port = <1>; mux-ext-port = <3>; }; + + sound-spdif { + compatible = "fsl,imx-audio-spdif"; + model = "imx-spdif"; + spdif-controller = <&spdif>; + spdif-out; + }; }; &audmux { @@ -81,6 +88,7 @@ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000 /* WL_REG_ON */ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* WL_HOST_WAKE */ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* WL_WAKE */ + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x80000000 >; }; }; @@ -90,6 +98,13 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet_1>; phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 29 0>; + status = "okay"; +}; + +&spdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spdif_3>; status = "okay"; }; @@ -115,6 +130,14 @@ status = "okay"; }; +&usbotg { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_1>; + disable-over-current; + dr_mode = "peripheral"; + status = "okay"; +}; + &usdhc1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc1_2>; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index ccd55c2..59154dc 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -116,6 +116,22 @@ arm,data-latency = <4 2 3>; }; + pcie: pcie@0x01000000 { + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; + reg = <0x01ffc000 0x4000>; /* DBI */ + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */ + 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */ + num-lanes = <1>; + interrupts = <0 123 0x04>; + clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>; + clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi"; + status = "disabled"; + }; + pmu { compatible = "arm,cortex-a9-pmu"; interrupts = <0 94 0x04>; @@ -136,8 +152,23 @@ ranges; spdif: spdif@02004000 { + compatible = "fsl,imx35-spdif"; reg = <0x02004000 0x4000>; interrupts = <0 52 0x04>; + dmas = <&sdma 14 18 0>, + <&sdma 15 18 0>; + dma-names = "rx", "tx"; + clocks = <&clks 197>, <&clks 3>, + <&clks 197>, <&clks 107>, + <&clks 0>, <&clks 118>, + <&clks 62>, <&clks 139>, + <&clks 0>; + clock-names = "core", "rxtx0", + "rxtx1", "rxtx2", + "rxtx3", "rxtx4", + "rxtx5", "rxtx6", + "rxtx7"; + status = "disabled"; }; ecspi1: ecspi@02008000 { @@ -1010,6 +1041,12 @@ MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0 >; }; + + pinctrl_spdif_3: spdifgrp-3 { + fsl,pins = < + MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1b0b0 + >; + }; }; uart1 { @@ -1184,6 +1221,36 @@ >; }; + pinctrl_usdhc3_1_100mhz: usdhc3grp-1-100mhz { /* 100Mhz */ + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170b9 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170b9 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170b9 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc3_1_200mhz: usdhc3grp-1-200mhz { /* 200Mhz */ + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170f9 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170f9 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170f9 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170f9 + >; + }; + pinctrl_usdhc3_2: usdhc3grp-2 { fsl,pins = < MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts index 2886a59..cc68e19 100644 --- a/arch/arm/boot/dts/imx6sl-evk.dts +++ b/arch/arm/boot/dts/imx6sl-evk.dts @@ -17,6 +17,44 @@ memory { reg = <0x80000000 0x40000000>; }; + + regulators { + compatible = "simple-bus"; + + reg_usb_otg1_vbus: usb_otg1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 0 0>; + enable-active-high; + }; + + reg_usb_otg2_vbus: usb_otg2_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 2 0>; + enable-active-high; + }; + }; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio4 11 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1_1>; + status = "okay"; + + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p32"; + spi-max-frequency = <20000000>; + reg = <0>; + }; }; &fec { @@ -38,6 +76,8 @@ MX6SL_PAD_SD2_DAT7__GPIO5_IO00 0x17059 MX6SL_PAD_SD2_DAT6__GPIO4_IO29 0x17059 MX6SL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059 + MX6SL_PAD_KEY_COL4__GPIO4_IO00 0x80000000 + MX6SL_PAD_KEY_COL5__GPIO4_IO02 0x80000000 >; }; }; @@ -49,9 +89,26 @@ status = "okay"; }; -&usdhc1 { +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1_1>; + disable-over-current; + status = "okay"; +}; + +&usbotg2 { + vbus-supply = <®_usb_otg2_vbus>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1_1>; + pinctrl-1 = <&pinctrl_usdhc1_1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_1_200mhz>; bus-width = <8>; cd-gpios = <&gpio4 7 0>; wp-gpios = <&gpio4 6 0>; @@ -59,16 +116,20 @@ }; &usdhc2 { - pinctrl-names = "default"; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc2_1>; + pinctrl-1 = <&pinctrl_usdhc2_1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_1_200mhz>; cd-gpios = <&gpio5 0 0>; wp-gpios = <&gpio4 29 0>; status = "okay"; }; &usdhc3 { - pinctrl-names = "default"; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc3_1>; + pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>; cd-gpios = <&gpio3 22 0>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index 177d9e7..28558f1 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -13,16 +13,20 @@ / { aliases { - serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; - serial3 = &uart4; - serial4 = &uart5; gpio0 = &gpio1; gpio1 = &gpio2; gpio2 = &gpio3; gpio3 = &gpio4; gpio4 = &gpio5; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + spi0 = &ecspi1; + spi1 = &ecspi2; + spi2 = &ecspi3; + spi3 = &ecspi4; }; cpus { @@ -530,10 +534,26 @@ interrupts = <0 89 0x04>; }; + gpr: iomuxc-gpr@020e0000 { + compatible = "fsl,imx6sl-iomuxc-gpr", + "fsl,imx6q-iomuxc-gpr", "syscon"; + reg = <0x020e0000 0x38>; + }; + iomuxc: iomuxc@020e0000 { compatible = "fsl,imx6sl-iomuxc"; reg = <0x020e0000 0x4000>; + ecspi1 { + pinctrl_ecspi1_1: ecspi1grp-1 { + fsl,pins = < + MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO 0x100b1 + MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1 + MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK 0x100b1 + >; + }; + }; + fec { pinctrl_fec_1: fecgrp-1 { fsl,pins = < @@ -559,6 +579,64 @@ }; }; + usbotg1 { + pinctrl_usbotg1_1: usbotg1grp-1 { + fsl,pins = < + MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059 + >; + }; + + pinctrl_usbotg1_2: usbotg1grp-2 { + fsl,pins = < + MX6SL_PAD_FEC_RXD0__USB_OTG1_ID 0x17059 + >; + }; + + pinctrl_usbotg1_3: usbotg1grp-3 { + fsl,pins = < + MX6SL_PAD_LCD_DAT1__USB_OTG1_ID 0x17059 + >; + }; + + pinctrl_usbotg1_4: usbotg1grp-4 { + fsl,pins = < + MX6SL_PAD_REF_CLK_32K__USB_OTG1_ID 0x17059 + >; + }; + + pinctrl_usbotg1_5: usbotg1grp-5 { + fsl,pins = < + MX6SL_PAD_SD3_DAT0__USB_OTG1_ID 0x17059 + >; + }; + }; + + usbotg2 { + pinctrl_usbotg2_1: usbotg2grp-1 { + fsl,pins = < + MX6SL_PAD_ECSPI1_SCLK__USB_OTG2_OC 0x17059 + >; + }; + + pinctrl_usbotg2_2: usbotg2grp-2 { + fsl,pins = < + MX6SL_PAD_ECSPI2_SCLK__USB_OTG2_OC 0x17059 + >; + }; + + pinctrl_usbotg2_3: usbotg2grp-3 { + fsl,pins = < + MX6SL_PAD_KEY_ROW5__USB_OTG2_OC 0x17059 + >; + }; + + pinctrl_usbotg2_4: usbotg2grp-4 { + fsl,pins = < + MX6SL_PAD_SD3_DAT2__USB_OTG2_OC 0x17059 + >; + }; + }; + usdhc1 { pinctrl_usdhc1_1: usdhc1grp-1 { fsl,pins = < @@ -574,6 +652,38 @@ MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x17059 >; }; + + pinctrl_usdhc1_1_100mhz: usdhc1grp-1-100mhz { + fsl,pins = < + MX6SL_PAD_SD1_CMD__SD1_CMD 0x170b9 + MX6SL_PAD_SD1_CLK__SD1_CLK 0x100b9 + MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170b9 + MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170b9 + MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170b9 + MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170b9 + MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170b9 + MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170b9 + MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170b9 + MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc1_1_200mhz: usdhc1grp-1-200mhz { + fsl,pins = < + MX6SL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6SL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170f9 + MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170f9 + MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170f9 + MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170f9 + >; + }; + + }; usdhc2 { @@ -587,6 +697,29 @@ MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x17059 >; }; + + pinctrl_usdhc2_1_100mhz: usdhc2grp-1-100mhz { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x170b9 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x100b9 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170b9 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170b9 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170b9 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_1_200mhz: usdhc2grp-1-200mhz { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x170f9 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x100f9 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 + >; + }; + }; usdhc3 { @@ -600,6 +733,28 @@ MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x17059 >; }; + + pinctrl_usdhc3_1_100mhz: usdhc3grp-1-100mhz { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x170b9 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x100b9 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170b9 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170b9 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170b9 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc3_1_200mhz: usdhc3grp-1-200mhz { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x170f9 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x100f9 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 + >; + }; }; }; @@ -621,7 +776,8 @@ <&clks IMX6SL_CLK_SDMA>; clock-names = "ipg", "ahb"; #dma-cells = <3>; - fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6sl.bin"; + /* imx6sl reuses imx6q sdma firmware */ + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin"; }; pxp: pxp@020f0000 { @@ -665,7 +821,7 @@ usbotg2: usb@02184200 { compatible = "fsl,imx6sl-usb", "fsl,imx27-usb"; reg = <0x02184200 0x200>; - interrupts = <0 40 0x04>; + interrupts = <0 42 0x04>; clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; @@ -675,7 +831,7 @@ usbh: usb@02184400 { compatible = "fsl,imx6sl-usb", "fsl,imx27-usb"; reg = <0x02184400 0x200>; - interrupts = <0 42 0x04>; + interrupts = <0 40 0x04>; clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 2>; status = "disabled"; diff --git a/arch/arm/boot/dts/kirkwood-db-88f6281.dts b/arch/arm/boot/dts/kirkwood-db-88f6281.dts index 72c4b0a..c39dd76 100644 --- a/arch/arm/boot/dts/kirkwood-db-88f6281.dts +++ b/arch/arm/boot/dts/kirkwood-db-88f6281.dts @@ -19,7 +19,6 @@ compatible = "marvell,db-88f6281-bp", "marvell,kirkwood-88f6281", "marvell,kirkwood"; mbus { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-db-88f6282.dts b/arch/arm/boot/dts/kirkwood-db-88f6282.dts index 36c411d..701c6b6 100644 --- a/arch/arm/boot/dts/kirkwood-db-88f6282.dts +++ b/arch/arm/boot/dts/kirkwood-db-88f6282.dts @@ -19,7 +19,6 @@ compatible = "marvell,db-88f6282-bp", "marvell,kirkwood-88f6282", "marvell,kirkwood"; mbus { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-db.dtsi b/arch/arm/boot/dts/kirkwood-db.dtsi index c0e2a58..053aa20 100644 --- a/arch/arm/boot/dts/kirkwood-db.dtsi +++ b/arch/arm/boot/dts/kirkwood-db.dtsi @@ -39,28 +39,6 @@ status = "ok"; }; - nand@3000000 { - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - chip-delay = <25>; - status = "okay"; - - partition@0 { - label = "uboot"; - reg = <0x0 0x100000>; - }; - - partition@100000 { - label = "uImage"; - reg = <0x100000 0x400000>; - }; - - partition@500000 { - label = "root"; - reg = <0x500000 0x1fb00000>; - }; - }; - sata@80000 { nr-ports = <2>; status = "okay"; @@ -80,6 +58,28 @@ }; }; +&nand { + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + chip-delay = <25>; + status = "okay"; + + partition@0 { + label = "uboot"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "uImage"; + reg = <0x100000 0x400000>; + }; + + partition@500000 { + label = "root"; + reg = <0x500000 0x1fb00000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/kirkwood-dnskw.dtsi index d544f77..aefa375 100644 --- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi +++ b/arch/arm/boot/dts/kirkwood-dnskw.dtsi @@ -148,44 +148,6 @@ status = "okay"; nr-ports = <2>; }; - - nand@3000000 { - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - status = "okay"; - chip-delay = <35>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x500000>; - }; - - partition@600000 { - label = "ramdisk"; - reg = <0x0600000 0x500000>; - }; - - partition@b00000 { - label = "image"; - reg = <0x0b00000 0x6600000>; - }; - - partition@7100000 { - label = "mini firmware"; - reg = <0x7100000 0xa00000>; - }; - - partition@7b00000 { - label = "config"; - reg = <0x7b00000 0x500000>; - }; - }; }; regulators { @@ -220,6 +182,44 @@ }; }; +&nand { + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + status = "okay"; + chip-delay = <35>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x500000>; + }; + + partition@600000 { + label = "ramdisk"; + reg = <0x0600000 0x500000>; + }; + + partition@b00000 { + label = "image"; + reg = <0x0b00000 0x6600000>; + }; + + partition@7100000 { + label = "mini firmware"; + reg = <0x7100000 0xa00000>; + }; + + partition@7b00000 { + label = "config"; + reg = <0x7b00000 0x500000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts index 59a2117..33ff368 100644 --- a/arch/arm/boot/dts/kirkwood-dockstar.dts +++ b/arch/arm/boot/dts/kirkwood-dockstar.dts @@ -34,26 +34,6 @@ serial@12000 { status = "ok"; }; - - nand@3000000 { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "data"; - reg = <0x0500000 0xfb00000>; - }; - }; }; gpio-leds { compatible = "gpio-leds"; @@ -91,6 +71,26 @@ }; }; +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x400000>; + }; + + partition@500000 { + label = "data"; + reg = <0x0500000 0xfb00000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts index 6f7c7d7..a43bebb 100644 --- a/arch/arm/boot/dts/kirkwood-goflexnet.dts +++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts @@ -67,31 +67,6 @@ status = "ok"; }; - nand@3000000 { - chip-delay = <40>; - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "pogoplug"; - reg = <0x0500000 0x2000000>; - }; - - partition@2500000 { - label = "root"; - reg = <0x02500000 0xd800000>; - }; - }; sata@80000 { status = "okay"; nr-ports = <2>; @@ -171,6 +146,32 @@ }; }; +&nand { + chip-delay = <40>; + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x400000>; + }; + + partition@500000 { + label = "pogoplug"; + reg = <0x0500000 0x2000000>; + }; + + partition@2500000 { + label = "root"; + reg = <0x02500000 0xd800000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts index 6548b9d..d30a91a 100644 --- a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts +++ b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts @@ -40,26 +40,6 @@ status = "ok"; }; - nand@3000000 { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x00000000 0x00100000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x00100000 0x00400000>; - }; - - partition@500000 { - label = "data"; - reg = <0x00500000 0x1fb00000>; - }; - }; - sata@80000 { status = "okay"; nr-ports = <1>; @@ -97,6 +77,26 @@ }; }; +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x00100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x00100000 0x00400000>; + }; + + partition@500000 { + label = "data"; + reg = <0x00500000 0x1fb00000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts index cb711a3..c5fb02f 100644 --- a/arch/arm/boot/dts/kirkwood-ib62x0.dts +++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts @@ -5,7 +5,7 @@ / { model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)"; - compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood"; memory { device_type = "memory"; @@ -43,6 +43,7 @@ marvell,function = "gpio"; }; }; + serial@12000 { status = "okay"; }; @@ -51,28 +52,6 @@ status = "okay"; nr-ports = <2>; }; - - nand@3000000 { - status = "okay"; - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x600000>; - }; - - partition@700000 { - label = "root"; - reg = <0x0700000 0xf900000>; - }; - - }; }; gpio_keys { @@ -93,6 +72,7 @@ gpios = <&gpio0 28 1>; }; }; + gpio-leds { compatible = "gpio-leds"; pinctrl-0 = <&pmx_led_os_red &pmx_led_os_green @@ -113,13 +93,39 @@ gpios = <&gpio0 27 0>; }; }; + gpio_poweroff { compatible = "gpio-poweroff"; pinctrl-0 = <&pmx_power_off>; pinctrl-names = "default"; gpios = <&gpio0 24 0>; }; +}; + +&nand { + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0xe0000>; + }; + partition@e0000 { + label = "u-boot environment"; + reg = <0xe0000 0x100000>; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x600000>; + }; + + partition@700000 { + label = "root"; + reg = <0x0700000 0xf900000>; + }; }; @@ -134,6 +140,7 @@ ð0 { status = "okay"; + ethernet0-port@0 { phy-handle = <ðphy0>; }; diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts index 0323f01..4a62b20 100644 --- a/arch/arm/boot/dts/kirkwood-iconnect.dts +++ b/arch/arm/boot/dts/kirkwood-iconnect.dts @@ -19,7 +19,6 @@ }; mbus { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; pcie-controller { status = "okay"; @@ -83,35 +82,6 @@ serial@12000 { status = "ok"; }; - - nand@3000000 { - status = "okay"; - - partition@0 { - label = "uboot"; - reg = <0x0000000 0xc0000>; - }; - - partition@a0000 { - label = "env"; - reg = <0xa0000 0x20000>; - }; - - partition@100000 { - label = "zImage"; - reg = <0x100000 0x300000>; - }; - - partition@540000 { - label = "initrd"; - reg = <0x540000 0x300000>; - }; - - partition@980000 { - label = "boot"; - reg = <0x980000 0x1f400000>; - }; - }; }; gpio-leds { @@ -180,6 +150,35 @@ }; }; +&nand { + status = "okay"; + + partition@0 { + label = "uboot"; + reg = <0x0000000 0xc0000>; + }; + + partition@a0000 { + label = "env"; + reg = <0xa0000 0x20000>; + }; + + partition@100000 { + label = "zImage"; + reg = <0x100000 0x300000>; + }; + + partition@540000 { + label = "initrd"; + reg = <0x540000 0x300000>; + }; + + partition@980000 { + label = "boot"; + reg = <0x980000 0x1f400000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts index df84474..d15395d 100644 --- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts +++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts @@ -113,31 +113,6 @@ status = "ok"; }; - nand@3000000 { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@a0000 { - label = "env"; - reg = <0xa0000 0x20000>; - read-only; - }; - - partition@100000 { - label = "uImage"; - reg = <0x100000 0x300000>; - }; - - partition@400000 { - label = "uInitrd"; - reg = <0x540000 0x1000000>; - }; - }; sata@80000 { status = "okay"; nr-ports = <2>; @@ -195,6 +170,32 @@ }; }; +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@a0000 { + label = "env"; + reg = <0xa0000 0x20000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x100000 0x300000>; + }; + + partition@400000 { + label = "uInitrd"; + reg = <0x540000 0x1000000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts index 6899408..cd44f37 100644 --- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts +++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts @@ -34,13 +34,6 @@ serial@12000 { status = "ok"; }; - - nand@3000000 { - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - status = "ok"; - chip-delay = <25>; - }; }; i2c@0 { @@ -51,6 +44,13 @@ }; }; +&nand { + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + status = "ok"; + chip-delay = <25>; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts index ce2b94b..6c1ec27 100644 --- a/arch/arm/boot/dts/kirkwood-mplcec4.dts +++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts @@ -17,7 +17,6 @@ }; mbus { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; pcie-controller { status = "okay"; @@ -96,37 +95,6 @@ pinctrl-names = "default"; }; - nand@3000000 { - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - status = "okay"; - - partition@0 { - label = "uboot"; - reg = <0x0000000 0x100000>; - }; - - partition@100000 { - label = "env"; - reg = <0x100000 0x80000>; - }; - - partition@180000 { - label = "fdt"; - reg = <0x180000 0x80000>; - }; - - partition@200000 { - label = "kernel"; - reg = <0x200000 0x400000>; - }; - - partition@600000 { - label = "rootfs"; - reg = <0x600000 0x1fa00000>; - }; - }; - rtc@10300 { status = "disabled"; }; @@ -194,6 +162,37 @@ }; }; +&nand { + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + status = "okay"; + + partition@0 { + label = "uboot"; + reg = <0x0000000 0x100000>; + }; + + partition@100000 { + label = "env"; + reg = <0x100000 0x80000>; + }; + + partition@180000 { + label = "fdt"; + reg = <0x180000 0x80000>; + }; + + partition@200000 { + label = "kernel"; + reg = <0x200000 0x400000>; + }; + + partition@600000 { + label = "rootfs"; + reg = <0x600000 0x1fa00000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts index 874857e..e6a102c 100644 --- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts +++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts @@ -17,7 +17,6 @@ }; mbus { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; pcie-controller { status = "okay"; @@ -98,36 +97,6 @@ status = "okay"; }; - nand@3000000 { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x180000>; - read-only; - }; - - partition@180000 { - label = "u-boot-env"; - reg = <0x180000 0x20000>; - }; - - partition@200000 { - label = "uImage"; - reg = <0x0200000 0x600000>; - }; - - partition@800000 { - label = "minirootfs"; - reg = <0x0800000 0x1000000>; - }; - - partition@1800000 { - label = "jffs2"; - reg = <0x1800000 0x6800000>; - }; - }; - sata@80000 { status = "okay"; nr-ports = <2>; @@ -208,6 +177,36 @@ }; }; +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x180000>; + read-only; + }; + + partition@180000 { + label = "u-boot-env"; + reg = <0x180000 0x20000>; + }; + + partition@200000 { + label = "uImage"; + reg = <0x0200000 0x600000>; + }; + + partition@800000 { + label = "minirootfs"; + reg = <0x0800000 0x1000000>; + }; + + partition@1800000 { + label = "jffs2"; + reg = <0x1800000 0x6800000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi index 06267a9..e3f915d 100644 --- a/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi +++ b/arch/arm/boot/dts/kirkwood-nsa310-common.dtsi @@ -27,49 +27,6 @@ nr-ports = <2>; }; - nand@3000000 { - status = "okay"; - chip-delay = <35>; - - partition@0 { - label = "uboot"; - reg = <0x0000000 0x0100000>; - read-only; - }; - partition@100000 { - label = "uboot_env"; - reg = <0x0100000 0x0080000>; - }; - partition@180000 { - label = "key_store"; - reg = <0x0180000 0x0080000>; - }; - partition@200000 { - label = "info"; - reg = <0x0200000 0x0080000>; - }; - partition@280000 { - label = "etc"; - reg = <0x0280000 0x0a00000>; - }; - partition@c80000 { - label = "kernel_1"; - reg = <0x0c80000 0x0a00000>; - }; - partition@1680000 { - label = "rootfs1"; - reg = <0x1680000 0x2fc0000>; - }; - partition@4640000 { - label = "kernel_2"; - reg = <0x4640000 0x0a00000>; - }; - partition@5040000 { - label = "rootfs2"; - reg = <0x5040000 0x2fc0000>; - }; - }; - pcie-controller { status = "okay"; @@ -105,3 +62,46 @@ }; }; }; + +&nand { + status = "okay"; + chip-delay = <35>; + + partition@0 { + label = "uboot"; + reg = <0x0000000 0x0100000>; + read-only; + }; + partition@100000 { + label = "uboot_env"; + reg = <0x0100000 0x0080000>; + }; + partition@180000 { + label = "key_store"; + reg = <0x0180000 0x0080000>; + }; + partition@200000 { + label = "info"; + reg = <0x0200000 0x0080000>; + }; + partition@280000 { + label = "etc"; + reg = <0x0280000 0x0a00000>; + }; + partition@c80000 { + label = "kernel_1"; + reg = <0x0c80000 0x0a00000>; + }; + partition@1680000 { + label = "rootfs1"; + reg = <0x1680000 0x2fc0000>; + }; + partition@4640000 { + label = "kernel_2"; + reg = <0x4640000 0x0a00000>; + }; + partition@5040000 { + label = "rootfs2"; + reg = <0x5040000 0x2fc0000>; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-nsa310.dts b/arch/arm/boot/dts/kirkwood-nsa310.dts index 7aeae0c..b5418bc 100644 --- a/arch/arm/boot/dts/kirkwood-nsa310.dts +++ b/arch/arm/boot/dts/kirkwood-nsa310.dts @@ -15,7 +15,6 @@ }; mbus { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts index 85ccf8d..f0e3d21 100644 --- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts +++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts @@ -29,43 +29,6 @@ pinctrl-names = "default"; }; - nand@3000000 { - chip-delay = <25>; - status = "okay"; - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - - partition@0 { - label = "uboot"; - reg = <0x0 0x90000>; - }; - - partition@90000 { - label = "env"; - reg = <0x90000 0x44000>; - }; - - partition@d4000 { - label = "test"; - reg = <0xd4000 0x24000>; - }; - - partition@f4000 { - label = "conf"; - reg = <0xf4000 0x400000>; - }; - - partition@4f4000 { - label = "linux"; - reg = <0x4f4000 0x1d20000>; - }; - - partition@2214000 { - label = "user"; - reg = <0x2214000 0x1dec000>; - }; - }; - sata@80000 { nr-ports = <1>; status = "okay"; @@ -167,6 +130,43 @@ }; }; +&nand { + chip-delay = <25>; + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partition@0 { + label = "uboot"; + reg = <0x0 0x90000>; + }; + + partition@90000 { + label = "env"; + reg = <0x90000 0x44000>; + }; + + partition@d4000 { + label = "test"; + reg = <0xd4000 0x24000>; + }; + + partition@f4000 { + label = "conf"; + reg = <0xf4000 0x400000>; + }; + + partition@4f4000 { + label = "linux"; + reg = <0x4f4000 0x1d20000>; + }; + + partition@2214000 { + label = "user"; + reg = <0x2214000 0x1dec000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a7.dts b/arch/arm/boot/dts/kirkwood-openblocks_a7.dts new file mode 100644 index 0000000..851fb2a --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-openblocks_a7.dts @@ -0,0 +1,223 @@ +/* + * Device Tree file for OpenBlocks A7 board + * + * Copyright (C) 2013 Free Electrons + * + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" + +/ { + model = "Plat'Home OpenBlocksA7"; + compatible = "plathome,openblocks-a7", "marvell,kirkwood-88f6283", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x40000000>; /* 1 GB */ + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + }; + + ocp@f1000000 { + serial@12000 { + status = "ok"; + pinctrl-0 = <&pmx_uart0>; + pinctrl-names = "default"; + }; + + serial@12100 { + status = "ok"; + pinctrl-0 = <&pmx_uart1>; + pinctrl-names = "default"; + }; + + sata@80000 { + nr-ports = <1>; + status = "okay"; + }; + + i2c@11100 { + status = "okay"; + pinctrl-0 = <&pmx_twsi1>; + pinctrl-names = "default"; + + s24c02: s24c02@50 { + compatible = "24c02"; + reg = <0x50>; + }; + }; + + pinctrl: pinctrl@10000 { + pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header>; + pinctrl-names = "default"; + + pmx_uart0: pmx-uart0 { + marvell,pins = "mpp10", "mpp11", "mpp15", + "mpp16"; + marvell,function = "uart0"; + }; + + pmx_uart1: pmx-uart1 { + marvell,pins = "mpp13", "mpp14", "mpp8", + "mpp9"; + marvell,function = "uart1"; + }; + + pmx_sysrst: pmx-sysrst { + marvell,pins = "mpp6"; + marvell,function = "sysrst"; + }; + + pmx_dip_switches: pmx-dip-switches { + marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47"; + marvell,function = "gpio"; + }; + + /* + * Accessible on connector J202. The MPP + * listed below are pin 1-7, pin 8 is unused, + * pin 9 is external reset input and pin 10 is + * ground. + */ + pmx_gpio_header: pmx-gpio-header { + marvell,pins = "mpp17", "mpp7", "mpp29", "mpp28", + "mpp35", "mpp34", "mpp40"; + marvell,function = "gpio"; + }; + + pmx_gpio_init: pmx-init { + marvell,pins = "mpp38"; + marvell,function = "gpio"; + }; + + pmx_usb_oc: pmx-usb-oc { + marvell,pins = "mpp39"; + marvell,function = "gpio"; + }; + + pmx_leds: pmx-leds { + marvell,pins = "mpp41", "mpp42", "mpp43"; + marvell,function = "gpio"; + }; + + pmx_ge1: pmx-ge1 { + marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23", + "mpp24", "mpp25", "mpp26", "mpp27", + "mpp30", "mpp31", "mpp32", "mpp33"; + marvell,function = "ge1"; + }; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_leds>; + pinctrl-names = "default"; + + led-red { + label = "obsa7:red:stat"; + gpios = <&gpio1 9 1>; + }; + + led-green { + label = "obsa7:green:stat"; + gpios = <&gpio1 10 1>; + }; + + led-yellow { + label = "obsa7:yellow:stat"; + gpios = <&gpio1 11 1>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pmx_gpio_init>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + button@1 { + label = "Init Button"; + linux,code = <116>; + gpios = <&gpio1 6 0>; + }; + }; +}; + +&nand { + chip-delay = <25>; + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partition@0 { + label = "uboot"; + reg = <0x0 0x1c0000>; + }; + + partition@1c0000 { + label = "env"; + reg = <0x1c0000 0x2c0000>; + }; + + partition@480000 { + label = "test"; + reg = <0x480000 0x160000>; + }; + + partition@5e0000 { + label = "conf"; + reg = <0x5e0000 0x540000>; + }; + + partition@b20000 { + label = "linux"; + reg = <0xb20000 0x3d40000>; + }; + + partition@4860000 { + label = "user"; + reg = <0x4860000 0xb7a0000>; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + device_type = "ethernet-phy"; + reg = <1>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; + +ð1 { + status = "okay"; + pinctrl-0 = <&pmx_ge1>; + pinctrl-names = "default"; + ethernet1-port@0 { + phy-handle = <ðphy1>; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi index 5696b63..1173d7f 100644 --- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi +++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi @@ -48,27 +48,6 @@ pinctrl-names = "default"; status = "okay"; }; - - nand@3000000 { - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - }; - - partition@100000 { - label = "uImage"; - reg = <0x0100000 0x400000>; - }; - - partition@500000 { - label = "root"; - reg = <0x0500000 0x1fb00000>; - }; - }; }; regulators { @@ -92,6 +71,27 @@ }; }; +&nand { + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x400000>; + }; + + partition@500000 { + label = "root"; + reg = <0x0500000 0x1fb00000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts index 30842b4..320da67 100644 --- a/arch/arm/boot/dts/kirkwood-topkick.dts +++ b/arch/arm/boot/dts/kirkwood-topkick.dts @@ -90,37 +90,6 @@ pinctrl-names = "default"; }; - nand@3000000 { - status = "okay"; - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x180000>; - }; - - partition@180000 { - label = "u-boot env"; - reg = <0x0180000 0x20000>; - }; - - partition@200000 { - label = "uImage"; - reg = <0x0200000 0x600000>; - }; - - partition@800000 { - label = "uInitrd"; - reg = <0x0800000 0x1000000>; - }; - - partition@1800000 { - label = "rootfs"; - reg = <0x1800000 0xe800000>; - }; - }; - sata@80000 { status = "okay"; nr-ports = <1>; @@ -204,6 +173,37 @@ }; }; +&nand { + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x180000>; + }; + + partition@180000 { + label = "u-boot env"; + reg = <0x0180000 0x20000>; + }; + + partition@200000 { + label = "uImage"; + reg = <0x0200000 0x600000>; + }; + + partition@800000 { + label = "uInitrd"; + reg = <0x0800000 0x1000000>; + }; + + partition@1800000 { + label = "rootfs"; + reg = <0x1800000 0xe800000>; + }; +}; + &mdio { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/kirkwood-ts219-6282.dts index 9efcd2d..345562f 100644 --- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts +++ b/arch/arm/boot/dts/kirkwood-ts219-6282.dts @@ -6,7 +6,6 @@ / { mbus { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>; pcie-controller { status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 1335b2e..8b73c80 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -28,16 +28,43 @@ compatible = "marvell,kirkwood-mbus", "simple-bus"; #address-cells = <2>; #size-cells = <1>; + /* If a board file needs to change this ranges it must replace it completely */ + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */ + MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */ + MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */ + >; controller = <&mbusc>; pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */ pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */ + + crypto@0301 { + compatible = "marvell,orion-crypto"; + reg = <MBUS_ID(0xf0, 0x01) 0x30000 0x10000>, + <MBUS_ID(0x03, 0x01) 0 0x800>; + reg-names = "regs", "sram"; + interrupts = <22>; + clocks = <&gate_clk 17>; + status = "okay"; + }; + + nand: nand@012f { + #address-cells = <1>; + #size-cells = <1>; + cle = <0>; + ale = <1>; + bank-width = <1>; + compatible = "marvell,orion-nand"; + reg = <MBUS_ID(0x01, 0x2f) 0 0x400>; + chip-delay = <25>; + /* set partition map and/or chip-delay in board dts */ + clocks = <&gate_clk 7>; + status = "disabled"; + }; }; ocp@f1000000 { compatible = "simple-bus"; - ranges = <0x00000000 0xf1000000 0x0100000 - 0xf4000000 0xf4000000 0x0000400 - 0xf5000000 0xf5000000 0x0000400>; + ranges = <0x00000000 0xf1000000 0x0100000>; #address-cells = <1>; #size-cells = <1>; @@ -193,20 +220,6 @@ status = "okay"; }; - nand@3000000 { - #address-cells = <1>; - #size-cells = <1>; - cle = <0>; - ale = <1>; - bank-width = <1>; - compatible = "marvell,orion-nand"; - reg = <0xf4000000 0x400>; - chip-delay = <25>; - /* set partition map and/or chip-delay in board dts */ - clocks = <&gate_clk 7>; - status = "disabled"; - }; - i2c@11000 { compatible = "marvell,mv64xxx-i2c"; reg = <0x11000 0x20>; @@ -218,16 +231,6 @@ status = "disabled"; }; - crypto@30000 { - compatible = "marvell,orion-crypto"; - reg = <0x30000 0x10000>, - <0xf5000000 0x800>; - reg-names = "regs", "sram"; - interrupts = <22>; - clocks = <&gate_clk 17>; - status = "okay"; - }; - mdio: mdio-bus@72004 { compatible = "marvell,orion-mdio"; #address-cells = <1>; diff --git a/arch/arm/boot/dts/mxs-pinfunc.h b/arch/arm/boot/dts/mxs-pinfunc.h new file mode 100644 index 0000000..c6da987 --- /dev/null +++ b/arch/arm/boot/dts/mxs-pinfunc.h @@ -0,0 +1,31 @@ +/* + * Header providing constants for i.MX28 pinctrl bindings. + * + * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DT_BINDINGS_MXS_PINCTRL_H__ +#define __DT_BINDINGS_MXS_PINCTRL_H__ + +/* fsl,drive-strength property */ +#define MXS_DRIVE_4mA 0 +#define MXS_DRIVE_8mA 1 +#define MXS_DRIVE_12mA 2 +#define MXS_DRIVE_16mA 3 + +/* fsl,voltage property */ +#define MXS_VOLTAGE_LOW 0 +#define MXS_VOLTAGE_HIGH 1 + +/* fsl,pull-up property */ +#define MXS_PULL_DISABLE 0 +#define MXS_PULL_ENABLE 1 + +#endif /* __DT_BINDINGS_MXS_PINCTRL_H__ */ diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi new file mode 100644 index 0000000..9c18adf --- /dev/null +++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi @@ -0,0 +1,52 @@ +/* + * Common file for GPMC connected smsc911x on omaps + * + * Note that the board specifc DTS file needs to specify + * ranges, pinctrl, reg, interrupt parent and interrupts. + */ + +/ { + vddvario: regulator-vddvario { + compatible = "regulator-fixed"; + regulator-name = "vddvario"; + regulator-always-on; + }; + + vdd33a: regulator-vdd33a { + compatible = "regulator-fixed"; + regulator-name = "vdd33a"; + regulator-always-on; + }; +}; + +&gpmc { + ethernet@gpmc { + compatible = "smsc,lan9221", "smsc,lan9115"; + bank-width = <2>; + gpmc,mux-add-data; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <186>; + gpmc,cs-wr-off-ns = <186>; + gpmc,adv-on-ns = <12>; + gpmc,adv-rd-off-ns = <48>; + gpmc,adv-wr-off-ns = <48>; + gpmc,oe-on-ns = <54>; + gpmc,oe-off-ns = <168>; + gpmc,we-on-ns = <54>; + gpmc,we-off-ns = <168>; + gpmc,rd-cycle-ns = <186>; + gpmc,wr-cycle-ns = <186>; + gpmc,access-ns = <114>; + gpmc,page-burst-access-ns = <6>; + gpmc,bus-turnaround-ns = <12>; + gpmc,cycle2cycle-delay-ns = <18>; + gpmc,wr-data-mux-bus-ns = <90>; + gpmc,wr-access-ns = <186>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + vmmc-supply = <&vddvario>; + vmmc_aux-supply = <&vdd33a>; + reg-io-width = <4>; + smsc,save-mac-address; + }; +}; diff --git a/arch/arm/boot/dts/omap-zoom-common.dtsi b/arch/arm/boot/dts/omap-zoom-common.dtsi new file mode 100644 index 0000000..b0ee342 --- /dev/null +++ b/arch/arm/boot/dts/omap-zoom-common.dtsi @@ -0,0 +1,33 @@ +/* + * Common features on the Zoom debug board + */ + +#include "omap-gpmc-smsc911x.dtsi" + +&gpmc { + ranges = <3 0 0x10000000 0x00000400>, + <7 0 0x2c000000 0x01000000>; + + /* + * Four port TL16CP754C serial port on GPMC, + * they probably share the same GPIO IRQ + * REVISIT: Add timing support from slls644g.pdf + */ + 8250@3,0 { + compatible = "ns16550a"; + reg = <3 0 0x100>; + bank-width = <2>; + reg-shift = <1>; + reg-io-width = <1>; + interrupt-parent = <&gpio4>; + interrupts = <6 IRQ_TYPE_EDGE_RISING>; /* gpio102 */ + clock-frequency = <1843200>; + current-speed = <115200>; + }; + + ethernet@gpmc { + reg = <7 0 0xff>; + interrupt-parent = <&gpio5>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>; /* gpio158 */ + }; +}; diff --git a/arch/arm/boot/dts/omap2420-h4.dts b/arch/arm/boot/dts/omap2420-h4.dts index 224c08f..34cdecb 100644 --- a/arch/arm/boot/dts/omap2420-h4.dts +++ b/arch/arm/boot/dts/omap2420-h4.dts @@ -50,15 +50,15 @@ label = "bootloader"; reg = <0 0x20000>; }; - partition@0x20000 { + partition@20000 { label = "params"; reg = <0x20000 0x20000>; }; - partition@0x40000 { + partition@40000 { label = "kernel"; reg = <0x40000 0x200000>; }; - partition@0x240000 { + partition@240000 { label = "file-system"; reg = <0x240000 0x3dc0000>; }; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index ba4dcfc..31a632f 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -69,6 +69,23 @@ }; }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */ + vcc-supply = <&hsusb2_power>; + }; }; &omap3_pmx_wkup { @@ -79,6 +96,37 @@ }; }; +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb2_pins + >; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ + >; + }; + + hsusbb2_pins: pinmux_hsusbb2_pins { + pinctrl-single,pins = < + 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + >; + }; +}; + &i2c1 { clock-frequency = <2600000>; @@ -150,15 +198,6 @@ power = <50>; }; -&omap3_pmx_core { - uart3_pins: pinmux_uart3_pins { - pinctrl-single,pins = < - 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ - >; - }; -}; - &uart3 { pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>; @@ -168,3 +207,11 @@ pinctrl-names = "default"; pinctrl-0 = <&gpio1_pins>; }; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index dfd8310..fa532aa 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -44,17 +44,6 @@ }; }; - /* HS USB Port 2 RESET */ - hsusb2_reset: hsusb2_reset_reg { - compatible = "regulator-fixed"; - regulator-name = "hsusb2_reset"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 19 0>; /* gpio_147 */ - startup-delay-us = <70000>; - enable-active-high; - }; - /* HS USB Port 2 Power */ hsusb2_power: hsusb2_power_reg { compatible = "regulator-fixed"; @@ -68,7 +57,7 @@ /* HS USB Host PHY on PORT 2 */ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv"; - reset-supply = <&hsusb2_reset>; + reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */ vcc-supply = <&hsusb2_power>; }; @@ -101,18 +90,18 @@ hsusbb2_pins: pinmux_hsusbb2_pins { pinctrl-single,pins = < - 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_clk */ - 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_stp */ - 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dir */ - 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_nxt */ - 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat0 */ - 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat1 */ - 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat2 */ - 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat3 */ - 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat4 */ - 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat5 */ - 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat6 */ - 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat7 */ + 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ >; }; @@ -180,3 +169,12 @@ pinctrl-names = "default"; pinctrl-0 = <&gpio1_pins>; }; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts index 7ef2827..4665421 100644 --- a/arch/arm/boot/dts/omap3-devkit8000.dts +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -125,7 +125,7 @@ nand-bus-width = <16>; gpmc,device-nand; - gpmc,sync-clki-ps = <0>; + gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; gpmc,cs-rd-off-ns = <44>; gpmc,cs-wr-off-ns = <44>; diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts new file mode 100644 index 0000000..4df68ad --- /dev/null +++ b/arch/arm/boot/dts/omap3-evm-37xx.dts @@ -0,0 +1,151 @@ +/* + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap36xx.dtsi" +#include "omap3-evm-common.dtsi" + + +/ { + model = "TI OMAP37XX EVM (TMDSEVM3730)"; + compatible = "ti,omap3-evm-37xx", "ti,omap36xx"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + wl12xx_vmmc: wl12xx_vmmc { + pinctrl-names = "default"; + pinctrl-0 = <&wl12xx_gpio>; + }; +}; + +&omap3_pmx_core { + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + 0x120 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ + 0x122 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ + 0x124 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ + 0x126 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ + >; + }; + + /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */ + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + 0x12e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16e (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + wl12xx_gpio: pinmux_wl12xx_gpio { + pinctrl-single,pins = < + 0x150 (PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */ + 0x14e (PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */ + >; + }; + + smsc911x_pins: pinmux_smsc911x_pins { + pinctrl-single,pins = < + 0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ + >; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; +}; + +&mmc3 { + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&gpmc { + ranges = <0 0 0x00000000 0x20000000>, + <5 0 0x2c000000 0x01000000>; + + nand@0,0 { + linux,mtd-name= "hynix,h8kds0un0mer-4em"; + reg = <0 0 0>; + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "X-Loader"; + reg = <0 0x80000>; + }; + partition@0x80000 { + label = "U-Boot"; + reg = <0x80000 0x1c0000>; + }; + partition@0x1c0000 { + label = "Environment"; + reg = <0x240000 0x40000>; + }; + partition@0x280000 { + label = "Kernel"; + reg = <0x280000 0x500000>; + }; + partition@0x780000 { + label = "Filesystem"; + reg = <0x780000 0x1f880000>; + }; + }; + + ethernet@gpmc { + pinctrl-names = "default"; + pinctrl-0 = <&smsc911x_pins>; + }; +}; diff --git a/arch/arm/boot/dts/omap3-evm-common.dtsi b/arch/arm/boot/dts/omap3-evm-common.dtsi new file mode 100644 index 0000000..3007e79 --- /dev/null +++ b/arch/arm/boot/dts/omap3-evm-common.dtsi @@ -0,0 +1,96 @@ +/* + * Common support for omap3 EVM boards + */ + +#include "omap-gpmc-smsc911x.dtsi" + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + leds { + compatible = "gpio-leds"; + ledb { + label = "omap3evm::ledb"; + gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */ + linux,default-trigger = "default-on"; + }; + }; + + wl12xx_vmmc: wl12xx_vmmc { + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 22 0>; /* gpio150 */ + startup-delay-us = <70000>; + enable-active-high; + vin-supply = <&vmmc2>; + }; +}; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; + + /* + * TVP5146 Video decoder-in for analog input support. + */ + tvp5146@5c { + compatible = "ti,tvp5146m2"; + reg = <0x5c>; + }; +}; + +&mmc1 { + vmmc-supply = <&vmmc1>; + vmmc_aux-supply = <&vsim>; + bus-width = <8>; +}; + +&mmc2 { + vmmc-supply = <&wl12xx_vmmc>; + non-removable; + bus-width = <4>; + cap-power-off-card; +}; + +&twl_gpio { + ti,use-leds; +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&gpmc { + ethernet@gpmc { + interrupt-parent = <&gpio6>; + interrupts = <16 8>; + reg = <5 0 0xff>; + }; +}; diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts index 4134dd0..e10dcd0 100644 --- a/arch/arm/boot/dts/omap3-evm.dts +++ b/arch/arm/boot/dts/omap3-evm.dts @@ -8,70 +8,14 @@ /dts-v1/; #include "omap34xx.dtsi" +#include "omap3-evm-common.dtsi" / { - model = "TI OMAP3 EVM (OMAP3530, AM/DM37x)"; + model = "TI OMAP35XX EVM (TMDSEVM3530)"; compatible = "ti,omap3-evm", "ti,omap3"; - cpus { - cpu@0 { - cpu0-supply = <&vcc>; - }; - }; - memory { device_type = "memory"; reg = <0x80000000 0x10000000>; /* 256 MB */ }; - - leds { - compatible = "gpio-leds"; - ledb { - label = "omap3evm::ledb"; - gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */ - linux,default-trigger = "default-on"; - }; - }; -}; - -&i2c1 { - clock-frequency = <2600000>; - - twl: twl@48 { - reg = <0x48>; - interrupts = <7>; /* SYS_NIRQ cascaded to intc */ - interrupt-parent = <&intc>; - }; -}; - -#include "twl4030.dtsi" -#include "twl4030_omap3.dtsi" - -&i2c2 { - clock-frequency = <400000>; -}; - -&i2c3 { - clock-frequency = <400000>; - - /* - * TVP5146 Video decoder-in for analog input support. - */ - tvp5146@5c { - compatible = "ti,tvp5146m2"; - reg = <0x5c>; - }; -}; - -&twl_gpio { - ti,use-leds; -}; - -&usb_otg_hs { - interface-type = <0>; - usb-phy = <&usb2_phy>; - phys = <&usb2_phy>; - phy-names = "usb2-phy"; - mode = <3>; - power = <50>; }; diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts new file mode 100644 index 0000000..b9b55c9 --- /dev/null +++ b/arch/arm/boot/dts/omap3-gta04.dts @@ -0,0 +1,170 @@ +/* + * Copyright (C) 2013 Marek Belisko <marek@goldelico.com> + * + * Based on omap3-beagle-xm.dts + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap36xx.dtsi" + +/ { + model = "OMAP3 GTA04"; + compatible = "ti,omap3-gta04", "ti,omap3"; + + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; + + gpio-keys { + compatible = "gpio-keys"; + + aux-button { + label = "aux"; + linux,code = <169>; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + gpio-key,wakeup; + }; + }; +}; + +&omap3_pmx_core { + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x152 (PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ + 0x14c (PIN_OUTPUT |MUX_MODE0) /* uart1_tx.uart1_tx */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ + 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx.uart3_rx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx.uart3_tx */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; +}; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&i2c2 { + clock-frequency = <400000>; + + /* pressure sensor */ + bmp085@77 { + compatible = "bosch,bmp085"; + reg = <0x77>; + }; + + /* leds */ + tca6507@45 { + compatible = "ti,tca6507"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x45>; + + gta04_led0: red_aux@0 { + label = "gta04:red:aux"; + reg = <0x0>; + }; + + gta04_led1: green_aux@1 { + label = "gta04:green:aux"; + reg = <0x1>; + }; + + gta04_led3: red_power@3 { + label = "gta04:red:power"; + reg = <0x3>; + linux,default-trigger = "default-on"; + }; + + gta04_led4: green_power@4 { + label = "gta04:green:power"; + reg = <0x4>; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + vmmc_aux-supply = <&vsim>; + bus-width = <4>; +}; + +&mmc2 { + status = "disabled"; +}; + +&mmc3 { + status = "disabled"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 2326d11..ba1e58b 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -77,6 +77,8 @@ 0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ >; }; + + leds_pins: pinmux_leds_pins { }; }; &i2c1 { @@ -141,3 +143,12 @@ &twl_gpio { ti,use-leds; }; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index e8c4828..d5cc792 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -10,13 +10,17 @@ */ #include "omap3-igep.dtsi" +#include "omap-gpmc-smsc911x.dtsi" / { model = "IGEPv2"; compatible = "isee,omap3-igep0020", "ti,omap3"; leds { + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins>; compatible = "gpio-leds"; + boot { label = "omap3:green:boot"; gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; @@ -41,19 +45,56 @@ }; }; - vddvario: regulator-vddvario { - compatible = "regulator-fixed"; - regulator-name = "vddvario"; - regulator-always-on; + /* HS USB Port 1 Power */ + hsusb1_power: hsusb1_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */ + vcc-supply = <&hsusb1_power>; }; +}; - vdd33a: regulator-vdd33a { - compatible = "regulator-fixed"; - regulator-name = "vdd33a"; - regulator-always-on; +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb1_pins + >; + + hsusbb1_pins: pinmux_hsusbb1_pins { + pinctrl-single,pins = < + 0x5aa (PIN_OUTPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */ + 0x5a8 (PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */ + 0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d8.hsusb1_dir */ + 0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d9.hsusb1_nxt */ + 0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d0.hsusb1_data0 */ + 0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d1.hsusb1_data1 */ + 0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d2.hsusb1_data2 */ + 0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d3.hsusb1_data7 */ + 0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d4.hsusb1_data4 */ + 0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d5.hsusb1_data5 */ + 0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d6.hsusb1_data6 */ + 0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */ + >; }; }; +&leds_pins { + pinctrl-single,pins = < + 0x5c4 (PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */ + 0x5c6 (PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */ + 0x5c8 (PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */ + >; +}; + &i2c3 { clock-frequency = <100000>; @@ -99,59 +140,37 @@ label = "SPL"; reg = <0 0x100000>; }; - partition@0x80000 { + partition@80000 { label = "U-Boot"; reg = <0x100000 0x180000>; }; - partition@0x1c0000 { + partition@1c0000 { label = "Environment"; reg = <0x280000 0x100000>; }; - partition@0x280000 { + partition@280000 { label = "Kernel"; reg = <0x380000 0x300000>; }; - partition@0x780000 { + partition@780000 { label = "Filesystem"; reg = <0x680000 0x1f980000>; }; }; - ethernet@5,0 { + ethernet@gpmc { pinctrl-names = "default"; pinctrl-0 = <&smsc911x_pins>; - compatible = "smsc,lan9221", "smsc,lan9115"; reg = <5 0 0xff>; - bank-width = <2>; - - gpmc,mux-add-data; - gpmc,cs-on-ns = <0>; - gpmc,cs-rd-off-ns = <186>; - gpmc,cs-wr-off-ns = <186>; - gpmc,adv-on-ns = <12>; - gpmc,adv-rd-off-ns = <48>; - gpmc,adv-wr-off-ns = <48>; - gpmc,oe-on-ns = <54>; - gpmc,oe-off-ns = <168>; - gpmc,we-on-ns = <54>; - gpmc,we-off-ns = <168>; - gpmc,rd-cycle-ns = <186>; - gpmc,wr-cycle-ns = <186>; - gpmc,access-ns = <114>; - gpmc,page-burst-access-ns = <6>; - gpmc,bus-turnaround-ns = <12>; - gpmc,cycle2cycle-delay-ns = <18>; - gpmc,wr-data-mux-bus-ns = <90>; - gpmc,wr-access-ns = <186>; - gpmc,cycle2cycle-samecsen; - gpmc,cycle2cycle-diffcsen; - interrupt-parent = <&gpio6>; - interrupts = <16 8>; - vmmc-supply = <&vddvario>; - vmmc_aux-supply = <&vdd33a>; - reg-io-width = <4>; - - smsc,save-mac-address; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; }; }; + +&usbhshost { + port1-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 644d053..525e6d9 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -16,7 +16,10 @@ compatible = "isee,omap3-igep0030", "ti,omap3"; leds { + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins>; compatible = "gpio-leds"; + boot { label = "omap3:green:boot"; gpios = <&twl_gpio 13 GPIO_ACTIVE_LOW>; @@ -43,6 +46,12 @@ }; }; +&leds_pins { + pinctrl-single,pins = < + 0x5b0 (PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */ + >; +}; + &gpmc { ranges = <0 0 0x00000000 0x20000000>; @@ -74,19 +83,19 @@ label = "SPL"; reg = <0 0x100000>; }; - partition@0x80000 { + partition@80000 { label = "U-Boot"; reg = <0x100000 0x180000>; }; - partition@0x1c0000 { + partition@1c0000 { label = "Environment"; reg = <0x280000 0x100000>; }; - partition@0x280000 { + partition@280000 { label = "Kernel"; reg = <0x380000 0x300000>; }; - partition@0x780000 { + partition@780000 { label = "Filesystem"; reg = <0x680000 0x1f980000>; }; diff --git a/arch/arm/boot/dts/omap3-n9.dts b/arch/arm/boot/dts/omap3-n9.dts new file mode 100644 index 0000000..39828ce --- /dev/null +++ b/arch/arm/boot/dts/omap3-n9.dts @@ -0,0 +1,18 @@ +/* + * omap3-n9.dts - Device Tree file for Nokia N9 + * + * Written by: Aaro Koskinen <aaro.koskinen@iki.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap3-n950-n9.dtsi" + +/ { + model = "Nokia N9"; + compatible = "nokia,omap3-n9", "ti,omap3"; +}; diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts new file mode 100644 index 0000000..c4f20bf --- /dev/null +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -0,0 +1,484 @@ +/* + * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz> + * Copyright 2013 Aaro Koskinen <aaro.koskinen@iki.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 (or later) as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap34xx.dtsi" + +/ { + model = "Nokia N900"; + compatible = "nokia,omap3-n900", "ti,omap3"; + + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + gpio_keys { + compatible = "gpio-keys"; + + camera_lens_cover { + label = "Camera Lens Cover"; + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */ + gpio-key,wakeup; + }; + + camera_focus { + label = "Camera Focus"; + gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */ + linux,code = <0x210>; /* KEY_CAMERA_FOCUS */ + gpio-key,wakeup; + }; + + camera_capture { + label = "Camera Capture"; + gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */ + linux,code = <0xd4>; /* KEY_CAMERA */ + gpio-key,wakeup; + }; + + lock_button { + label = "Lock Button"; + gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */ + linux,code = <0x98>; /* KEY_SCREENLOCK */ + gpio-key,wakeup; + }; + + keypad_slide { + label = "Keypad Slide"; + gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */ + gpio-key,wakeup; + }; + + proximity_sensor { + label = "Proximity Sensor"; + gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */ + }; + }; + +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */ + 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x18a (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x18e (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + 0x190 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + 0x192 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + 0x194 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */ + 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */ + 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ + 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ + 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ + >; + }; + + display_pins: pinmux_display_pins { + pinctrl-single,pins = < + 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */ + >; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <2200000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&vaux1 { + regulator-name = "V28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; /* due battery cover sensor */ +}; + +&vaux2 { + regulator-name = "VCSI"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&vaux3 { + regulator-name = "VMMC2_30"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3000000>; +}; + +&vaux4 { + regulator-name = "VCAM_ANA_28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +&vmmc1 { + regulator-name = "VMMC1"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; +}; + +&vmmc2 { + regulator-name = "V28_A"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; /* due VIO leak to AIC34 VDDs */ +}; + +&vpll1 { + regulator-name = "VPLL"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&vpll2 { + regulator-name = "VSDI_CSI"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&vsim { + regulator-name = "VMMC2_IO_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +&vio { + regulator-name = "VIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + +}; + +&vintana1 { + regulator-name = "VINTANA1"; + /* fixed to 1500000 */ + regulator-always-on; +}; + +&vintana2 { + regulator-name = "VINTANA2"; + regulator-min-microvolt = <2750000>; + regulator-max-microvolt = <2750000>; + regulator-always-on; +}; + +&vintdig { + regulator-name = "VINTDIG"; + /* fixed to 1500000 */ + regulator-always-on; +}; + +&twl { + twl_audio: audio { + compatible = "ti,twl4030-audio"; + ti,enable-vibra = <1>; + }; +}; + +&twl_gpio { + ti,pullups = <0x0>; + ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */ +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <100000>; + + tlv320aic3x: tlv320aic3x@18 { + compatible = "ti,tlv320aic3x"; + reg = <0x18>; + gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */ + ai3x-gpio-func = < + 0 /* AIC3X_GPIO1_FUNC_DISABLED */ + 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */ + >; + + AVDD-supply = <&vmmc2>; + DRVDD-supply = <&vmmc2>; + IOVDD-supply = <&vio>; + DVDD-supply = <&vio>; + }; + + tlv320aic3x_aux: tlv320aic3x@19 { + compatible = "ti,tlv320aic3x"; + reg = <0x19>; + gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */ + + AVDD-supply = <&vmmc2>; + DRVDD-supply = <&vmmc2>; + IOVDD-supply = <&vio>; + DVDD-supply = <&vio>; + }; + + lp5523: lp5523@32 { + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */ + enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */ + + chan0 { + chan-name = "lp5523:kb1"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan1 { + chan-name = "lp5523:kb2"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan2 { + chan-name = "lp5523:kb3"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan3 { + chan-name = "lp5523:kb4"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan4 { + chan-name = "lp5523:b"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan5 { + chan-name = "lp5523:g"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan6 { + chan-name = "lp5523:r"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan7 { + chan-name = "lp5523:kb5"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + + chan8 { + chan-name = "lp5523:kb6"; + led-cur = /bits/ 8 <50>; + max-cur = /bits/ 8 <100>; + }; + }; + + bq27200: bq27200@55 { + compatible = "ti,bq27200"; + reg = <0x55>; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + + clock-frequency = <400000>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */ +}; + +&mmc2 { + status = "disabled"; +}; + +&mmc3 { + status = "disabled"; +}; + +&gpmc { + ranges = <0 0 0x04000000 0x10000000>; /* 256MB */ + + /* gpio-irq for dma: 65 */ + + onenand@0,0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0 0 0x10000000>; + + gpmc,sync-read; + gpmc,sync-write; + gpmc,burst-length = <16>; + gpmc,burst-read; + gpmc,burst-wrap; + gpmc,burst-write; + gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */ + gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */ + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <87>; + gpmc,cs-wr-off-ns = <87>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <15>; + gpmc,oe-off-ns = <87>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <87>; + gpmc,rd-cycle-ns = <112>; + gpmc,wr-cycle-ns = <112>; + gpmc,access-ns = <81>; + gpmc,page-burst-access-ns = <15>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,clk-activation-ns = <5>; + gpmc,wr-data-mux-bus-ns = <30>; + gpmc,wr-access-ns = <81>; + gpmc,sync-clk-ps = <15000>; + + /* + * MTD partition table corresponding to Nokia's + * Maemo 5 (Fremantle) release. + */ + partition@0 { + label = "bootloader"; + reg = <0x00000000 0x00020000>; + read-only; + }; + partition@1 { + label = "config"; + reg = <0x00020000 0x00060000>; + }; + partition@2 { + label = "log"; + reg = <0x00080000 0x00040000>; + }; + partition@3 { + label = "kernel"; + reg = <0x000c0000 0x00200000>; + }; + partition@4 { + label = "initfs"; + reg = <0x002c0000 0x00200000>; + }; + partition@5 { + label = "rootfs"; + reg = <0x004c0000 0x0fb40000>; + }; + }; +}; + +&mcspi1 { + /* + * For some reason, touchscreen is necessary for screen to work at + * all on real hw. It works well without it on emulator. + * + * Also... order in the device tree actually matters here. + */ + tsc2005@0 { + compatible = "tsc2005"; + spi-max-frequency = <6000000>; + reg = <0>; + }; + mipid@2 { + compatible = "acx565akm"; + spi-max-frequency = <6000000>; + reg = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&display_pins>; + }; +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <2>; + power = <50>; +}; + +&uart1 { + status = "disabled"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi new file mode 100644 index 0000000..94eb77d --- /dev/null +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -0,0 +1,174 @@ +/* + * omap3-n950-n9.dtsi - Device Tree file for Nokia N950 & N9 (common stuff) + * + * Written by: Aaro Koskinen <aaro.koskinen@iki.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "omap36xx.dtsi" + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1 GB */ + }; + + vemmc: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "VEMMC"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + gpio = <&gpio5 29 0>; /* gpio line 157 */ + startup-delay-us = <150>; + enable-active-high; + }; +}; + +&omap3_pmx_core { + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ + 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ + 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ + >; + }; +}; + +&i2c1 { + clock-frequency = <2900000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + }; +}; + +/include/ "twl4030.dtsi" + +&twl { + compatible = "ti,twl5031"; +}; + +&twl_gpio { + ti,pullups = <0x000001>; /* BIT(0) */ + ti,pulldowns = <0x008106>; /* BIT(1) | BIT(2) | BIT(8) | BIT(15) */ +}; + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; +}; + +&mmc1 { + status = "disabled"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&vemmc>; + bus-width = <4>; + ti,non-removable; +}; + +&mmc3 { + status = "disabled"; +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&gpmc { + ranges = <0 0 0x04000000 0x20000000>; + + onenand@0,0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0 0 0x20000000>; + + gpmc,sync-read; + gpmc,sync-write; + gpmc,burst-length = <16>; + gpmc,burst-read; + gpmc,burst-wrap; + gpmc,burst-write; + gpmc,device-width = <2>; + gpmc,mux-add-data = <2>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <87>; + gpmc,cs-wr-off-ns = <87>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <15>; + gpmc,oe-off-ns = <87>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <87>; + gpmc,rd-cycle-ns = <112>; + gpmc,wr-cycle-ns = <112>; + gpmc,access-ns = <81>; + gpmc,page-burst-access-ns = <15>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,clk-activation-ns = <5>; + gpmc,wr-data-mux-bus-ns = <30>; + gpmc,wr-access-ns = <81>; + gpmc,sync-clk-ps = <15000>; + + /* + * MTD partition table corresponding to Nokia's MeeGo 1.2 + * Harmattan release. + */ + partition@0 { + label = "bootloader"; + reg = <0x00000000 0x00100000>; + }; + partition@1 { + label = "config"; + reg = <0x00100000 0x002c0000>; + }; + partition@2 { + label = "kernel"; + reg = <0x003c0000 0x01000000>; + }; + partition@3 { + label = "log"; + reg = <0x013c0000 0x00200000>; + }; + partition@4 { + label = "var"; + reg = <0x015c0000 0x1ca40000>; + }; + partition@5 { + label = "moslo"; + reg = <0x1e000000 0x02000000>; + }; + partition@6 { + label = "omap2-onenand"; + reg = <0x00000000 0x20000000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap3-n950.dts b/arch/arm/boot/dts/omap3-n950.dts new file mode 100644 index 0000000..b076a52 --- /dev/null +++ b/arch/arm/boot/dts/omap3-n950.dts @@ -0,0 +1,18 @@ +/* + * omap3-n950.dts - Device Tree file for Nokia N950 + * + * Written by: Aaro Koskinen <aaro.koskinen@iki.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "omap3-n950-n9.dtsi" + +/ { + model = "Nokia N950"; + compatible = "nokia,omap3-n950", "ti,omap3"; +}; diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts new file mode 100644 index 0000000..15eb9fe --- /dev/null +++ b/arch/arm/boot/dts/omap3-zoom3.dts @@ -0,0 +1,217 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap36xx.dtsi" +#include "omap-zoom-common.dtsi" + +/ { + model = "TI Zoom3"; + compatible = "ti,omap3-zoom3", "ti,omap36xx", "ti,omap3"; + + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; + + vddvario: regulator-vddvario { + compatible = "regulator-fixed"; + regulator-name = "vddvario"; + regulator-always-on; + }; + + vdd33a: regulator-vdd33a { + compatible = "regulator-fixed"; + regulator-name = "vdd33a"; + regulator-always-on; + }; + + wl12xx_vmmc: wl12xx_vmmc { + pinctrl-names = "default"; + pinctrl-0 = <&wl12xx_gpio>; + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio4 5 0>; /* gpio101 */ + startup-delay-us = <70000>; + enable-active-high; + }; +}; + +&omap3_pmx_core { + /* REVISIT: twl gpio0 is mmc0_cd */ + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + 0x116 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + 0x12c (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + 0x12e (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + 0x130 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + 0x132 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + 0x134 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat4.sdmmc2_dat4 */ + 0x136 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat5.sdmmc2_dat5 */ + 0x138 (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat6.sdmmc2_dat6 */ + 0x13a (PIN_INPUT | MUX_MODE0) /* sdmmc2_dat7.sdmmc2_dat7 */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + 0x168 (PIN_INPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 WLAN IRQ */ + 0x1a0 (PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */ + 0x5a8 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + 0x5b4 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d4.sdmmc3_dat0 */ + 0x5b6 (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */ + 0x5b8 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d6.sdmmc3_dat2 */ + 0x5b2 (PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d3.sdmmc3_dat3 */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x150 (PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */ + 0x14e (PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */ + 0x152 (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ + 0x14c (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0x144 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */ + 0x146 (PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ + 0x14a (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ + 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x16a (PIN_INPUT_PULLDOWN | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ + 0x16c (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ + 0x16e (WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + /* wl12xx GPIO output for WLAN_EN */ + wl12xx_gpio: pinmux_wl12xx_gpio { + pinctrl-single,pins = < + 0xea (PIN_OUTPUT| MUX_MODE4) /* cam_d2.gpio_101 */ + >; + }; +}; + +&omap3_pmx_wkup { + wlan_host_wkup: pinmux_wlan_host_wkup_pins { + pinctrl-single,pins = < + 0x1a (PIN_INPUT_PULLUP | MUX_MODE4) /* sys_clkout1.gpio_10 WLAN_HOST_WKUP */ + >; + }; +}; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + }; +}; + +#include "twl4030.dtsi" + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; + + /* + * TVP5146 Video decoder-in for analog input support. + */ + tvp5146@5c { + compatible = "ti,tvp5146m2"; + reg = <0x5c>; + }; +}; + +&twl_gpio { + ti,use-leds; +}; + +&mmc1 { + vmmc-supply = <&vmmc1>; + vmmc_aux-supply = <&vsim>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; +}; +/* +&mmc2 { + vmmc-supply = <&vmmc2>; + ti,non-removable; + bus-width = <8>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; +}; +*/ +&mmc3 { + vmmc-supply = <&wl12xx_vmmc>; + non-removable; + bus-width = <4>; + cap-power-off-card; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&uart4 { + status = "disabled"; +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index b41bd57..f3a0c26 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -19,6 +19,9 @@ interrupt-parent = <&intc>; aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -37,6 +40,7 @@ pmu { compatible = "arm,cortex-a8-pmu"; + reg = <0x54000000 0x800000>; interrupts = <3>; ti,hwmods = "debugss"; }; @@ -71,6 +75,8 @@ */ ocp { compatible = "simple-bus"; + reg = <0x68000000 0x10000>; + interrupts = <9 10>; #address-cells = <1>; #size-cells = <1>; ranges; @@ -107,15 +113,19 @@ reg = <0x48002030 0x05cc>; #address-cells = <1>; #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0xff1f>; }; - omap3_pmx_wkup: pinmux@0x48002a00 { + omap3_pmx_wkup: pinmux@48002a00 { compatible = "ti,omap3-padconf", "pinctrl-single"; reg = <0x48002a00 0x5c>; #address-cells = <1>; #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0xff1f>; }; @@ -189,24 +199,40 @@ uart1: serial@4806a000 { compatible = "ti,omap3-uart"; + reg = <0x4806a000 0x2000>; + interrupts = <72>; + dmas = <&sdma 49 &sdma 50>; + dma-names = "tx", "rx"; ti,hwmods = "uart1"; clock-frequency = <48000000>; }; uart2: serial@4806c000 { compatible = "ti,omap3-uart"; + reg = <0x4806c000 0x400>; + interrupts = <73>; + dmas = <&sdma 51 &sdma 52>; + dma-names = "tx", "rx"; ti,hwmods = "uart2"; clock-frequency = <48000000>; }; uart3: serial@49020000 { compatible = "ti,omap3-uart"; + reg = <0x49020000 0x400>; + interrupts = <74>; + dmas = <&sdma 53 &sdma 54>; + dma-names = "tx", "rx"; ti,hwmods = "uart3"; clock-frequency = <48000000>; }; i2c1: i2c@48070000 { compatible = "ti,omap3-i2c"; + reg = <0x48070000 0x80>; + interrupts = <56>; + dmas = <&sdma 27 &sdma 28>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c1"; @@ -214,6 +240,10 @@ i2c2: i2c@48072000 { compatible = "ti,omap3-i2c"; + reg = <0x48072000 0x80>; + interrupts = <57>; + dmas = <&sdma 29 &sdma 30>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c2"; @@ -221,6 +251,10 @@ i2c3: i2c@48060000 { compatible = "ti,omap3-i2c"; + reg = <0x48060000 0x80>; + interrupts = <61>; + dmas = <&sdma 25 &sdma 26>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c3"; @@ -228,6 +262,8 @@ mcspi1: spi@48098000 { compatible = "ti,omap2-mcspi"; + reg = <0x48098000 0x100>; + interrupts = <65>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi1"; @@ -246,6 +282,8 @@ mcspi2: spi@4809a000 { compatible = "ti,omap2-mcspi"; + reg = <0x4809a000 0x100>; + interrupts = <66>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi2"; @@ -259,6 +297,8 @@ mcspi3: spi@480b8000 { compatible = "ti,omap2-mcspi"; + reg = <0x480b8000 0x100>; + interrupts = <91>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi3"; @@ -272,6 +312,8 @@ mcspi4: spi@480ba000 { compatible = "ti,omap2-mcspi"; + reg = <0x480ba000 0x100>; + interrupts = <48>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi4"; @@ -280,8 +322,17 @@ dma-names = "tx0", "rx0"; }; + hdqw1w: 1w@480b2000 { + compatible = "ti,omap3-1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + ti,hwmods = "hdq1w"; + }; + mmc1: mmc@4809c000 { compatible = "ti,omap3-hsmmc"; + reg = <0x4809c000 0x200>; + interrupts = <83>; ti,hwmods = "mmc1"; ti,dual-volt; dmas = <&sdma 61>, <&sdma 62>; @@ -290,6 +341,8 @@ mmc2: mmc@480b4000 { compatible = "ti,omap3-hsmmc"; + reg = <0x480b4000 0x200>; + interrupts = <86>; ti,hwmods = "mmc2"; dmas = <&sdma 47>, <&sdma 48>; dma-names = "tx", "rx"; @@ -297,6 +350,8 @@ mmc3: mmc@480ad000 { compatible = "ti,omap3-hsmmc"; + reg = <0x480ad000 0x200>; + interrupts = <94>; ti,hwmods = "mmc3"; dmas = <&sdma 77>, <&sdma 78>; dma-names = "tx", "rx"; @@ -304,6 +359,7 @@ wdt2: wdt@48314000 { compatible = "ti,omap3-wdt"; + reg = <0x48314000 0x80>; ti,hwmods = "wd_timer2"; }; diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/omap3430-sdp.dts index e2249bc..281914e 100644 --- a/arch/arm/boot/dts/omap3430-sdp.dts +++ b/arch/arm/boot/dts/omap3430-sdp.dts @@ -84,15 +84,15 @@ label = "bootloader-nor"; reg = <0 0x40000>; }; - partition@0x40000 { + partition@40000 { label = "params-nor"; reg = <0x40000 0x40000>; }; - partition@0x80000 { + partition@80000 { label = "kernel-nor"; reg = <0x80000 0x200000>; }; - partition@0x280000 { + partition@280000 { label = "filesystem-nor"; reg = <0x240000 0x7d80000>; }; @@ -125,19 +125,19 @@ label = "xloader-nand"; reg = <0 0x80000>; }; - partition@0x80000 { + partition@80000 { label = "bootloader-nand"; reg = <0x80000 0x140000>; }; - partition@0x1c0000 { + partition@1c0000 { label = "params-nand"; reg = <0x1c0000 0xc0000>; }; - partition@0x280000 { + partition@280000 { label = "kernel-nand"; reg = <0x280000 0x500000>; }; - partition@0x780000 { + partition@780000 { label = "filesystem-nand"; reg = <0x780000 0x7880000>; }; @@ -170,19 +170,19 @@ label = "xloader-onenand"; reg = <0 0x80000>; }; - partition@0x80000 { + partition@80000 { label = "bootloader-onenand"; reg = <0x80000 0x40000>; }; - partition@0xc0000 { + partition@c0000 { label = "params-onenand"; reg = <0xc0000 0x20000>; }; - partition@0xe0000 { + partition@e0000 { label = "kernel-onenand"; reg = <0xe0000 0x200000>; }; - partition@0x2e0000 { + partition@2e0000 { label = "filesystem-onenand"; reg = <0x2e0000 0xfd20000>; }; diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi index f8b3765..380c22e 100644 --- a/arch/arm/boot/dts/omap36xx.dtsi +++ b/arch/arm/boot/dts/omap36xx.dtsi @@ -31,6 +31,10 @@ ocp { uart4: serial@49042000 { compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + dmas = <&sdma 81 &sdma 82>; + dma-names = "tx", "rx"; ti,hwmods = "uart4"; clock-frequency = <48000000>; }; diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 814ab67..298e850 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -60,22 +60,6 @@ "AFMR", "Line In"; }; - /* - * Temp hack: Need to be replaced with the proper gpio-controlled - * reset driver as soon it will be merged. - * http://thread.gmane.org/gmane.linux.drivers.devicetree/36830 - */ - /* HS USB Port 1 RESET */ - hsusb1_reset: hsusb1_reset_reg { - compatible = "regulator-fixed"; - regulator-name = "hsusb1_reset"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio2 30 0>; /* gpio_62 */ - startup-delay-us = <70000>; - enable-active-high; - }; - /* HS USB Port 1 Power */ hsusb1_power: hsusb1_power_reg { compatible = "regulator-fixed"; @@ -97,7 +81,7 @@ /* HS USB Host PHY on PORT 1 */ hsusb1_phy: hsusb1_phy { compatible = "usb-nop-xceiv"; - reset-supply = <&hsusb1_reset>; + reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */ vcc-supply = <&hsusb1_power>; /** * FIXME: @@ -122,37 +106,19 @@ }; }; -&omap4_pmx_wkup { - pinctrl-names = "default"; - pinctrl-0 = < - &twl6030_wkup_pins - >; - - twl6030_wkup_pins: pinmux_twl6030_wkup_pins { - pinctrl-single,pins = < - 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */ - >; - }; -}; - &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < - &twl6030_pins &twl6040_pins &mcpdm_pins &mcbsp1_pins + &dss_dpi_pins + &tfp410_pins &dss_hdmi_pins &tpd12s015_pins &hsusbb1_pins >; - twl6030_pins: pinmux_twl6030_pins { - pinctrl-single,pins = < - 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */ - >; - }; - twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ @@ -179,6 +145,47 @@ >; }; + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + 0x122 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */ + 0x124 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */ + 0x126 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */ + 0x128 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */ + 0x12a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */ + 0x12c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */ + 0x12e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */ + 0x130 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */ + 0x132 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */ + 0x134 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */ + 0x136 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */ + + 0x174 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */ + 0x176 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */ + 0x178 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */ + 0x17a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */ + 0x17c (PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */ + 0x17e (PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */ + 0x180 (PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */ + 0x182 (PIN_OUTPUT | MUX_MODE5) /* dispc2_de */ + 0x184 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */ + 0x186 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */ + 0x188 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */ + 0x18a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */ + 0x18c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */ + 0x18e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */ + + 0x190 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */ + 0x192 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */ + 0x194 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */ + >; + }; + + tfp410_pins: pinmux_tfp410_pins { + pinctrl-single,pins = < + 0x144 (PIN_OUTPUT | MUX_MODE3) /* gpio_0 */ + >; + }; + dss_hdmi_pins: pinmux_dss_hdmi_pins { pinctrl-single,pins = < 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ @@ -305,6 +312,7 @@ }; #include "twl6030.dtsi" +#include "twl6030_omap4.dtsi" &i2c2 { pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index 56c4354..816d1c9 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -62,3 +62,7 @@ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; }; }; + +&gpio1 { + ti,no-reset-on-init; +}; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 4f78380..5fc3f43 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -155,23 +155,9 @@ }; }; -&omap4_pmx_wkup { - pinctrl-names = "default"; - pinctrl-0 = < - &twl6030_wkup_pins - >; - - twl6030_wkup_pins: pinmux_twl6030_wkup_pins { - pinctrl-single,pins = < - 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */ - >; - }; -}; - &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < - &twl6030_pins &twl6040_pins &mcpdm_pins &dmic_pins @@ -206,12 +192,6 @@ >; }; - twl6030_pins: pinmux_twl6030_pins { - pinctrl-single,pins = < - 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */ - >; - }; - twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ @@ -370,6 +350,7 @@ }; #include "twl6030.dtsi" +#include "twl6030_omap4.dtsi" &i2c2 { pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index ea4054b..a1e0585 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -17,6 +17,10 @@ interrupt-parent = <&gic>; aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -56,7 +60,7 @@ cache-level = <2>; }; - local-timer@0x48240600 { + local-timer@48240600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x48240600 0x20>; interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>; @@ -114,6 +118,8 @@ reg = <0x4a100040 0x0196>; #address-cells = <1>; #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0x7fff>; }; @@ -122,6 +128,8 @@ reg = <0x4a31e040 0x0038>; #address-cells = <1>; #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0x7fff>; }; @@ -214,6 +222,7 @@ gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; ti,hwmods = "gpmc"; + ti,no-idle-on-init; }; uart1: serial@4806a000 { @@ -248,6 +257,12 @@ clock-frequency = <48000000>; }; + hwspinlock: spinlock@4a0f6000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x4a0f6000 0x1000>; + ti,hwmods = "spinlock"; + }; + i2c1: i2c@48070000 { compatible = "ti,omap4-i2c"; reg = <0x48070000 0x100>; @@ -492,6 +507,7 @@ reg = <0x4c000000 0x100>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "emif1"; + ti,no-idle-on-init; phy-type = <1>; hw-caps-read-idle-ctrl; hw-caps-ll-interface; @@ -503,6 +519,7 @@ reg = <0x4d000000 0x100>; interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "emif2"; + ti,no-idle-on-init; phy-type = <1>; hw-caps-read-idle-ctrl; hw-caps-ll-interface; @@ -670,5 +687,23 @@ ram-bits = <12>; ctrl-module = <&omap_control_usbotg>; }; + + aes: aes@4b501000 { + compatible = "ti,omap4-aes"; + ti,hwmods = "aes"; + reg = <0x4b501000 0xa0>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 111>, <&sdma 110>; + dma-names = "tx", "rx"; + }; + + des: des@480a5000 { + compatible = "ti,omap4-des"; + ti,hwmods = "des"; + reg = <0x480a5000 0xa0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 117>, <&sdma 116>; + dma-names = "tx", "rx"; + }; }; }; diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 65d7b60..002fa70 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -27,21 +27,10 @@ regulator-max-microvolt = <3000000>; }; - /* HS USB Port 2 RESET */ - hsusb2_reset: hsusb2_reset_reg { - compatible = "regulator-fixed"; - regulator-name = "hsusb2_reset"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 HUB_NRESET */ - startup-delay-us = <70000>; - enable-active-high; - }; - /* HS USB Host PHY on PORT 2 */ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv"; - reset-supply = <&hsusb2_reset>; + reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ /** * FIXME * Put the right clock phandle here when available @@ -51,21 +40,10 @@ clock-frequency = <19200000>; }; - /* HS USB Port 3 RESET */ - hsusb3_reset: hsusb3_reset_reg { - compatible = "regulator-fixed"; - regulator-name = "hsusb3_reset"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; /* gpio3_79 ETH_NRESET */ - startup-delay-us = <70000>; - enable-active-high; - }; - /* HS USB Host PHY on PORT 3 */ hsusb3_phy: hsusb3_phy { compatible = "usb-nop-xceiv"; - reset-supply = <&hsusb3_reset>; + reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ }; leds { @@ -84,7 +62,6 @@ pinctrl-0 = < &twl6040_pins &mcpdm_pins - &dmic_pins &mcbsp1_pins &mcbsp2_pins &usbhost_pins @@ -93,7 +70,7 @@ twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */ + 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ >; }; @@ -107,15 +84,6 @@ >; }; - dmic_pins: pinmux_dmic_pins { - pinctrl-single,pins = < - 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */ - 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */ - 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */ - 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */ - >; - }; - mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ @@ -153,25 +121,25 @@ 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ - 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */ + 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ >; }; mcspi3_pins: pinmux_mcspi3_pins { pinctrl-single,pins = < - 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ - 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ - 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ - 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ + 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ + 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ + 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ + 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ >; }; mcspi4_pins: pinmux_mcspi4_pins { pinctrl-single,pins = < - 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ - 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ - 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ - 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ + 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */ + 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */ + 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */ + 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */ >; }; @@ -271,6 +239,14 @@ reg = <0x48>; interrupt-controller; #interrupt-cells = <2>; + ti,system-power-controller; + + extcon_usb3: palmas_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + ti,wakeup; + }; palmas_pmic { compatible = "ti,palmas-pmic"; @@ -334,15 +310,22 @@ ti,smps-range = <0x80>; }; - smps10_reg: smps10 { + smps10_out2_reg: smps10_out2 { /* VBUS_5V_OTG */ - regulator-name = "smps10"; + regulator-name = "smps10_out2"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-always-on; regulator-boot-on; }; + smps10_out1_reg: smps10_out1 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + ldo1_reg: ldo1 { /* VDDAPHY_CAM: vdda_csiport */ regulator-name = "ldo1"; @@ -470,6 +453,11 @@ phys = <0 &hsusb2_phy &hsusb3_phy>; }; +&usb3 { + extcon = <&extcon_usb3>; + vbus-supply = <&smps10_out1_reg>; +}; + &mcspi1 { }; @@ -503,3 +491,7 @@ pinctrl-names = "default"; pinctrl-0 = <&uart5_pins>; }; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index c0ec6dc..fc3fad5 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -21,6 +21,11 @@ interrupt-parent = <&gic>; aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; + i2c4 = &i2c5; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -33,10 +38,17 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a15"; reg = <0x0>; + + operating-points = < + /* kHz uV */ + 500000 880000 + 1000000 1060000 + 1500000 1250000 + >; }; cpu@1 { device_type = "cpu"; @@ -52,7 +64,6 @@ <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>; - clock-frequency = <6144000>; }; gic: interrupt-controller@48211000 { @@ -276,6 +287,12 @@ ti,hwmods = "i2c5"; }; + hwspinlock: spinlock@4a0f6000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x4a0f6000 0x1000>; + ti,hwmods = "spinlock"; + }; + mcspi1: spi@48098000 { compatible = "ti,omap4-mcspi"; reg = <0x48098000 0x200>; @@ -604,9 +621,10 @@ ti,hwmods = "wd_timer2"; }; - emif1: emif@0x4c000000 { + emif1: emif@4c000000 { compatible = "ti,emif-4d5"; ti,hwmods = "emif1"; + ti,no-idle-on-init; phy-type = <2>; /* DDR PHY type: Intelli PHY */ reg = <0x4c000000 0x400>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; @@ -615,9 +633,10 @@ hw-caps-temp-alert; }; - emif2: emif@0x4d000000 { + emif2: emif@4d000000 { compatible = "ti,emif-4d5"; ti,hwmods = "emif2"; + ti,no-idle-on-init; phy-type = <2>; /* DDR PHY type: Intelli PHY */ reg = <0x4d000000 0x400>; interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; @@ -638,7 +657,7 @@ reg-names = "power"; }; - omap_dwc3@4a020000 { + usb3: omap_dwc3@4a020000 { compatible = "ti,dwc3"; ti,hwmods = "usb_otg_ss"; reg = <0x4a020000 0x10000>; @@ -652,6 +671,7 @@ reg = <0x4a030000 0x10000>; interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; usb-phy = <&usb2_phy>, <&usb3_phy>; + dr_mode = "peripheral"; tx-fifo-resize; }; }; diff --git a/arch/arm/boot/dts/prima2.dtsi b/arch/arm/boot/dts/prima2.dtsi index 27ed9f5..7cf78af 100644 --- a/arch/arm/boot/dts/prima2.dtsi +++ b/arch/arm/boot/dts/prima2.dtsi @@ -76,6 +76,11 @@ compatible = "sirf,prima2-rsc"; reg = <0x88020000 0x1000>; }; + + cphifbg@88030000 { + compatible = "sirf,prima2-cphifbg"; + reg = <0x88030000 0x1000>; + }; }; mem-iobg { @@ -86,10 +91,17 @@ memory-controller@90000000 { compatible = "sirf,prima2-memc"; - reg = <0x90000000 0x10000>; + reg = <0x90000000 0x2000>; interrupts = <27>; clocks = <&clks 5>; }; + + memc-monitor { + compatible = "sirf,prima2-memcmon"; + reg = <0x90002000 0x200>; + interrupts = <4>; + clocks = <&clks 32>; + }; }; disp-iobg { @@ -287,7 +299,13 @@ compatible = "sirf,prima2-spi"; reg = <0xb00d0000 0x10000>; interrupts = <15>; + sirf,spi-num-chipselects = <1>; + sirf,spi-dma-rx-channel = <25>; + sirf,spi-dma-tx-channel = <20>; + #address-cells = <1>; + #size-cells = <0>; clocks = <&clks 19>; + status = "disabled"; }; spi1: spi@b0170000 { @@ -295,7 +313,13 @@ compatible = "sirf,prima2-spi"; reg = <0xb0170000 0x10000>; interrupts = <16>; + sirf,spi-num-chipselects = <1>; + sirf,spi-dma-rx-channel = <12>; + sirf,spi-dma-tx-channel = <13>; + #address-cells = <1>; + #size-cells = <0>; clocks = <&clks 20>; + status = "disabled"; }; i2c0: i2c@b00e0000 { @@ -304,6 +328,8 @@ reg = <0xb00e0000 0x10000>; interrupts = <24>; clocks = <&clks 17>; + #address-cells = <1>; + #size-cells = <0>; }; i2c1: i2c@b00f0000 { @@ -312,6 +338,8 @@ reg = <0xb00f0000 0x10000>; interrupts = <25>; clocks = <&clks 18>; + #address-cells = <1>; + #size-cells = <0>; }; tsc@b0110000 { diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts b/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts index f444624..9443e93 100644 --- a/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts +++ b/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts @@ -10,6 +10,7 @@ /dts-v1/; /include/ "r8a73a4.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "APE6EVM"; @@ -24,6 +25,34 @@ reg = <0 0x40000000 0 0x40000000>; }; + vcc_mmc0: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "MMC0 Vcc"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + vcc_sdhi0: regulator@1 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&pfc 76 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + /* Common 3.3V rail, used by several devices on APE6EVM */ + ape6evm_fixed_3v3: regulator@2 { + compatible = "regulator-fixed"; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + lbsc { compatible = "simple-bus"; #address-cells = <1>; @@ -33,6 +62,7 @@ }; &i2c5 { + status = "okay"; vdd_dvfs: max8973@1b { compatible = "maxim,max8973"; reg = <0x1b>; @@ -62,4 +92,47 @@ renesas,groups = "scifa0_data"; renesas,function = "scifa0"; }; + + mmc0_pins: mmcif { + renesas,groups = "mmc0_data8", "mmc0_ctrl"; + renesas,function = "mmc0"; + }; + + sdhi0_pins: sdhi0 { + renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd"; + renesas,function = "sdhi0"; + }; + + sdhi1_pins: sdhi1 { + renesas,groups = "sdhi1_data4", "sdhi1_ctrl"; + renesas,function = "sdhi1"; + }; +}; + +&mmcif0 { + vmmc-supply = <&vcc_mmc0>; + bus-width = <8>; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + status = "okay"; +}; + +&sdhi0 { + vmmc-supply = <&vcc_sdhi0>; + bus-width = <4>; + toshiba,mmc-wrprotect-disable; + pinctrl-names = "default"; + pinctrl-0 = <&sdhi0_pins>; + status = "okay"; +}; + +&sdhi1 { + vmmc-supply = <&ape6evm_fixed_3v3>; + bus-width = <4>; + broken-cd; + toshiba,mmc-wrprotect-disable; + pinctrl-names = "default"; + pinctrl-0 = <&sdhi1_pins>; + status = "okay"; }; diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts index 72f867e..91436b5 100644 --- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts +++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts @@ -52,6 +52,7 @@ }; &i2c5 { + status = "okay"; vdd_dvfs: max8973@1b { compatible = "maxim,max8973"; reg = <0x1b>; diff --git a/arch/arm/boot/dts/r8a73a4.dtsi b/arch/arm/boot/dts/r8a73a4.dtsi index 658fcc5..287e047 100644 --- a/arch/arm/boot/dts/r8a73a4.dtsi +++ b/arch/arm/boot/dts/r8a73a4.dtsi @@ -78,6 +78,49 @@ <0 56 4>, <0 57 4>; }; + dmac: dma-multiplexer@0 { + compatible = "renesas,shdma-mux"; + #dma-cells = <1>; + dma-channels = <20>; + dma-requests = <256>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dma0: dma-controller@e6700020 { + compatible = "renesas,shdma-r8a73a4"; + reg = <0 0xe6700020 0 0x89e0>; + interrupt-parent = <&gic>; + interrupts = <0 220 4 + 0 200 4 + 0 201 4 + 0 202 4 + 0 203 4 + 0 204 4 + 0 205 4 + 0 206 4 + 0 207 4 + 0 208 4 + 0 209 4 + 0 210 4 + 0 211 4 + 0 212 4 + 0 213 4 + 0 214 4 + 0 215 4 + 0 216 4 + 0 217 4 + 0 218 4 + 0 219 4>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19"; + }; + }; + thermal@e61f0000 { compatible = "renesas,rcar-thermal"; reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>, @@ -93,6 +136,7 @@ reg = <0 0xe6500000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 174 0x4>; + status = "disabled"; }; i2c1: i2c@e6510000 { @@ -102,6 +146,7 @@ reg = <0 0xe6510000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 175 0x4>; + status = "disabled"; }; i2c2: i2c@e6520000 { @@ -111,6 +156,7 @@ reg = <0 0xe6520000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 176 0x4>; + status = "disabled"; }; i2c3: i2c@e6530000 { @@ -120,6 +166,7 @@ reg = <0 0xe6530000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 177 0x4>; + status = "disabled"; }; i2c4: i2c@e6540000 { @@ -129,6 +176,7 @@ reg = <0 0xe6540000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 178 0x4>; + status = "disabled"; }; i2c5: i2c@e60b0000 { @@ -138,6 +186,7 @@ reg = <0 0xe60b0000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 179 0x4>; + status = "disabled"; }; i2c6: i2c@e6550000 { @@ -147,6 +196,7 @@ reg = <0 0xe6550000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 184 0x4>; + status = "disabled"; }; i2c7: i2c@e6560000 { @@ -156,6 +206,7 @@ reg = <0 0xe6560000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 185 0x4>; + status = "disabled"; }; i2c8: i2c@e6570000 { @@ -165,6 +216,7 @@ reg = <0 0xe6570000 0 0x428>; interrupt-parent = <&gic>; interrupts = <0 173 0x4>; + status = "disabled"; }; mmcif0: mmcif@ee200000 { diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts index c638e4a..1c56c5e 100644 --- a/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts +++ b/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts @@ -11,6 +11,7 @@ /dts-v1/; /include/ "r8a7740.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pwm/pwm.h> / { model = "armadillo 800 eva reference"; @@ -34,6 +35,33 @@ regulator-boot-on; }; + vcc_sdhi0: regulator@1 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&pfc 75 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi0: regulator@2 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI0 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_sdhi0>; + + enable-gpio = <&pfc 74 GPIO_ACTIVE_HIGH>; + gpios = <&pfc 17 GPIO_ACTIVE_HIGH>; + states = <3300000 0 + 1800000 1>; + + enable-active-high; + }; + leds { compatible = "gpio-leds"; led1 { @@ -49,9 +77,19 @@ gpios = <&pfc 177 GPIO_ACTIVE_HIGH>; }; }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&tpu 2 33333 PWM_POLARITY_INVERTED>; + brightness-levels = <0 1 2 4 8 16 32 64 128 255>; + default-brightness-level = <9>; + pinctrl-0 = <&backlight_pins>; + pinctrl-names = "default"; + }; }; &i2c0 { + status = "okay"; touchscreen: st1232@55 { compatible = "sitronix,st1232"; reg = <0x55>; @@ -76,4 +114,44 @@ renesas,groups = "intc_irq10"; renesas,function = "intc"; }; + + backlight_pins: backlight { + renesas,groups = "tpu0_to2_1"; + renesas,function = "tpu0"; + }; + + mmc0_pins: mmc0 { + renesas,groups = "mmc0_data8_1", "mmc0_ctrl_1"; + renesas,function = "mmc0"; + }; + + sdhi0_pins: sdhi0 { + renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_wp"; + renesas,function = "sdhi0"; + }; +}; + +&tpu { + status = "okay"; +}; + +&mmcif0 { + pinctrl-0 = <&mmc0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <®_3p3v>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&sdhi0 { + pinctrl-0 = <&sdhi0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi0>; + vqmmc-supply = <&vccq_sdhi0>; + bus-width = <4>; + cd-gpios = <&pfc 167 GPIO_ACTIVE_LOW>; + status = "okay"; }; diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/r8a7740.dtsi index 44d3d52..ae1e230 100644 --- a/arch/arm/boot/dts/r8a7740.dtsi +++ b/arch/arm/boot/dts/r8a7740.dtsi @@ -131,6 +131,7 @@ 0 202 0x4 0 203 0x4 0 204 0x4>; + status = "disabled"; }; i2c1: i2c@e6c20000 { @@ -143,6 +144,7 @@ 0 71 0x4 0 72 0x4 0 73 0x4>; + status = "disabled"; }; pfc: pfc@e6050000 { @@ -159,4 +161,37 @@ status = "disabled"; #pwm-cells = <3>; }; + + mmcif0: mmcif@e6bd0000 { + compatible = "renesas,sh-mmcif"; + reg = <0xe6bd0000 0x100>; + interrupt-parent = <&gic>; + interrupts = <0 56 4 + 0 57 4>; + status = "disabled"; + }; + + sdhi0: sdhi@e6850000 { + compatible = "renesas,sdhi-r8a7740"; + reg = <0xe6850000 0x100>; + interrupt-parent = <&gic>; + interrupts = <0 117 4 + 0 118 4 + 0 119 4>; + cap-sd-highspeed; + cap-sdio-irq; + status = "disabled"; + }; + + sdhi1: sdhi@e6860000 { + compatible = "renesas,sdhi-r8a7740"; + reg = <0xe6860000 0x100>; + interrupt-parent = <&gic>; + interrupts = <0 121 4 + 0 122 4 + 0 123 4>; + cap-sd-highspeed; + cap-sdio-irq; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/r8a7778-bockw-reference.dts b/arch/arm/boot/dts/r8a7778-bockw-reference.dts index 9bb903a..969e386 100644 --- a/arch/arm/boot/dts/r8a7778-bockw-reference.dts +++ b/arch/arm/boot/dts/r8a7778-bockw-reference.dts @@ -22,11 +22,36 @@ compatible = "renesas,bockw-reference", "renesas,r8a7778"; chosen { - bootargs = "console=ttySC0,115200 ignore_loglevel rw"; + bootargs = "console=ttySC0,115200 ignore_loglevel root=/dev/nfs ip=dhcp rw"; }; memory { device_type = "memory"; reg = <0x60000000 0x10000000>; }; + + fixedregulator3v3: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ethernet@18300000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0x18300000 0x1000>; + + phy-mode = "mii"; + interrupt-parent = <&irqpin>; + interrupts = <0 0>; /* IRQ0: hwirq 0 on irqpin */ + reg-io-width = <4>; + vddvario-supply = <&fixedregulator3v3>; + vdd33a-supply = <&fixedregulator3v3>; + }; +}; + +&irqpin { + status = "okay"; }; diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi index 3577aba..a6308a3 100644 --- a/arch/arm/boot/dts/r8a7778.dtsi +++ b/arch/arm/boot/dts/r8a7778.dtsi @@ -33,6 +33,25 @@ <0xfe430000 0x100>; }; + /* irqpin: IRQ0 - IRQ3 */ + irqpin: irqpin@fe78001c { + compatible = "renesas,intc-irqpin"; + #interrupt-cells = <2>; + interrupt-controller; + status = "disabled"; /* default off */ + reg = <0xfe78001c 4>, + <0xfe780010 4>, + <0xfe780024 4>, + <0xfe780044 4>, + <0xfe780064 4>; + interrupt-parent = <&gic>; + interrupts = <0 27 0x4 + 0 28 0x4 + 0 29 0x4 + 0 30 0x4>; + sense-bitfield-width = <2>; + }; + gpio0: gpio@ffc40000 { compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar"; reg = <0xffc40000 0x2c>; diff --git a/arch/arm/boot/dts/r8a7779-marzen-reference.dts b/arch/arm/boot/dts/r8a7779-marzen-reference.dts index 6d55083..ab4110a 100644 --- a/arch/arm/boot/dts/r8a7779-marzen-reference.dts +++ b/arch/arm/boot/dts/r8a7779-marzen-reference.dts @@ -42,8 +42,8 @@ pinctrl-names = "default"; phy-mode = "mii"; - interrupt-parent = <&gic>; - interrupts = <0 28 0x4>; + interrupt-parent = <&irqpin0>; + interrupts = <1 0>; /* IRQ1: hwirq 1 on irqpin0 */ reg-io-width = <4>; vddvario-supply = <&fixedregulator3v3>; vdd33a-supply = <&fixedregulator3v3>; @@ -63,6 +63,10 @@ }; }; +&irqpin0 { + status = "okay"; +}; + &pfc { pinctrl-0 = <&scif2_pins &scif4_pins &sdhi0_pins>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi index ebbe507..19faeac 100644 --- a/arch/arm/boot/dts/r8a7779.dtsi +++ b/arch/arm/boot/dts/r8a7779.dtsi @@ -135,6 +135,7 @@ irqpin0: irqpin@fe780010 { compatible = "renesas,intc-irqpin"; #interrupt-cells = <2>; + status = "disabled"; interrupt-controller; reg = <0xfe78001c 4>, <0xfe780010 4>, @@ -156,6 +157,7 @@ reg = <0xffc70000 0x1000>; interrupt-parent = <&gic>; interrupts = <0 79 0x4>; + status = "disabled"; }; i2c1: i2c@ffc71000 { @@ -165,6 +167,7 @@ reg = <0xffc71000 0x1000>; interrupt-parent = <&gic>; interrupts = <0 82 0x4>; + status = "disabled"; }; i2c2: i2c@ffc72000 { @@ -174,6 +177,7 @@ reg = <0xffc72000 0x1000>; interrupt-parent = <&gic>; interrupts = <0 80 0x4>; + status = "disabled"; }; i2c3: i2c@ffc73000 { @@ -183,6 +187,7 @@ reg = <0xffc73000 0x1000>; interrupt-parent = <&gic>; interrupts = <0 81 0x4>; + status = "disabled"; }; pfc: pfc@fffc0000 { diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index 413b4c2..ee845fa 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -24,6 +24,55 @@ reg = <0>; clock-frequency = <1300000000>; }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <1>; + clock-frequency = <1300000000>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <2>; + clock-frequency = <1300000000>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <3>; + clock-frequency = <1300000000>; + }; + + cpu4: cpu@4 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + clock-frequency = <780000000>; + }; + + cpu5: cpu@5 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + clock-frequency = <780000000>; + }; + + cpu6: cpu@6 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x102>; + clock-frequency = <780000000>; + }; + + cpu7: cpu@7 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x103>; + clock-frequency = <780000000>; + }; }; gic: interrupt-controller@f1001000 { @@ -127,6 +176,46 @@ interrupts = <0 0 4>, <0 1 4>, <0 2 4>, <0 3 4>; }; + i2c0: i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7790"; + reg = <0 0xe6508000 0 0x40>; + interrupt-parent = <&gic>; + interrupts = <0 287 0x4>; + status = "disabled"; + }; + + i2c1: i2c@e6518000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7790"; + reg = <0 0xe6518000 0 0x40>; + interrupt-parent = <&gic>; + interrupts = <0 288 0x4>; + status = "disabled"; + }; + + i2c2: i2c@e6530000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7790"; + reg = <0 0xe6530000 0 0x40>; + interrupt-parent = <&gic>; + interrupts = <0 286 0x4>; + status = "disabled"; + }; + + i2c3: i2c@e6540000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7790"; + reg = <0 0xe6540000 0 0x40>; + interrupt-parent = <&gic>; + interrupts = <0 290 0x4>; + status = "disabled"; + }; + mmcif0: mmcif@ee200000 { compatible = "renesas,sh-mmcif"; reg = <0 0xee200000 0 0x80>; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index bbed43b..fea5cfe 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -25,6 +25,13 @@ reg = <0>; clock-frequency = <1300000000>; }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <1>; + clock-frequency = <1300000000>; + }; }; gic: interrupt-controller@f1001000 { @@ -38,4 +45,30 @@ <0 0xf1006000 0 0x2000>; interrupts = <1 9 0xf04>; }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = <1 13 0xf08>, + <1 14 0xf08>, + <1 11 0xf08>, + <1 10 0xf08>; + }; + + irqc0: interrupt-controller@e61c0000 { + compatible = "renesas,irqc"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0 0xe61c0000 0 0x200>; + interrupt-parent = <&gic>; + interrupts = <0 0 4>, + <0 1 4>, + <0 2 4>, + <0 3 4>, + <0 12 4>, + <0 13 4>, + <0 14 4>, + <0 15 4>, + <0 16 4>, + <0 17 4>; + }; }; diff --git a/arch/arm/boot/dts/s3c6400.dtsi b/arch/arm/boot/dts/s3c6400.dtsi new file mode 100644 index 0000000..a7d1c8e --- /dev/null +++ b/arch/arm/boot/dts/s3c6400.dtsi @@ -0,0 +1,41 @@ +/* + * Samsung's S3C6400 SoC device tree source + * + * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com> + * + * Samsung's S3C6400 SoC device nodes are listed in this file. S3C6400 + * based board files can include this file and provide values for board specfic + * bindings. + * + * Note: This file does not include device nodes for all the controllers in + * S3C6400 SoC. As device tree coverage for S3C6400 increases, additional + * nodes can be added to this file. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include "s3c64xx.dtsi" + +/ { + compatible = "samsung,s3c6400"; +}; + +&vic0 { + valid-mask = <0xfffffe1f>; + valid-wakeup-mask = <0x00200004>; +}; + +&vic1 { + valid-mask = <0xffffffff>; + valid-wakeup-mask = <0x53020000>; +}; + +&soc { + clocks: clock-controller@7e00f000 { + compatible = "samsung,s3c6400-clock"; + reg = <0x7e00f000 0x1000>; + #clock-cells = <1>; + }; +}; diff --git a/arch/arm/boot/dts/s3c6410-mini6410.dts b/arch/arm/boot/dts/s3c6410-mini6410.dts new file mode 100644 index 0000000..57e00f9 --- /dev/null +++ b/arch/arm/boot/dts/s3c6410-mini6410.dts @@ -0,0 +1,228 @@ +/* + * Samsung's S3C6410 based Mini6410 board device tree source + * + * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com> + * + * Device tree source file for FriendlyARM Mini6410 board which is based on + * Samsung's S3C6410 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#include "s3c6410.dtsi" + +/ { + model = "FriendlyARM Mini6410 board based on S3C6410"; + compatible = "friendlyarm,mini6410", "samsung,s3c6410"; + + memory { + reg = <0x50000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1"; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + fin_pll: oscillator@0 { + compatible = "fixed-clock"; + reg = <0>; + clock-frequency = <12000000>; + clock-output-names = "fin_pll"; + #clock-cells = <0>; + }; + + xusbxti: oscillator@1 { + compatible = "fixed-clock"; + reg = <1>; + clock-output-names = "xusbxti"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + }; + + srom-cs1@18000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x18000000 0x8000000>; + ranges; + + ethernet@18000000 { + compatible = "davicom,dm9000"; + reg = <0x18000000 0x2 0x18000004 0x2>; + interrupt-parent = <&gpn>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH>; + davicom,no-eeprom; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys>; + autorepeat; + + button-k1 { + label = "K1"; + gpios = <&gpn 0 GPIO_ACTIVE_LOW>; + linux,code = <2>; + debounce-interval = <20>; + }; + + button-k2 { + label = "K2"; + gpios = <&gpn 1 GPIO_ACTIVE_LOW>; + linux,code = <3>; + debounce-interval = <20>; + }; + + button-k3 { + label = "K3"; + gpios = <&gpn 2 GPIO_ACTIVE_LOW>; + linux,code = <4>; + debounce-interval = <20>; + }; + + button-k4 { + label = "K4"; + gpios = <&gpn 3 GPIO_ACTIVE_LOW>; + linux,code = <5>; + debounce-interval = <20>; + }; + + button-k5 { + label = "K5"; + gpios = <&gpn 4 GPIO_ACTIVE_LOW>; + linux,code = <6>; + debounce-interval = <20>; + }; + + button-k6 { + label = "K6"; + gpios = <&gpn 5 GPIO_ACTIVE_LOW>; + linux,code = <7>; + debounce-interval = <20>; + }; + + button-k7 { + label = "K7"; + gpios = <&gpl 11 GPIO_ACTIVE_LOW>; + linux,code = <8>; + debounce-interval = <20>; + }; + + button-k8 { + label = "K8"; + gpios = <&gpl 12 GPIO_ACTIVE_LOW>; + linux,code = <9>; + debounce-interval = <20>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_leds>; + + led-1 { + label = "LED1"; + gpios = <&gpk 4 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + led-2 { + label = "LED2"; + gpios = <&gpk 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "mmc0"; + }; + + led-3 { + label = "LED3"; + gpios = <&gpk 6 GPIO_ACTIVE_LOW>; + }; + + led-4 { + label = "LED4"; + gpios = <&gpk 7 GPIO_ACTIVE_LOW>; + }; + }; + + buzzer { + compatible = "pwm-beeper"; + pwms = <&pwm 0 1000000 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_out>; + }; +}; + +&sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; + bus-width = <4>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_data>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_data>, <&uart1_fctl>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_data>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_data>; + status = "okay"; +}; + +&pwm { + status = "okay"; +}; + +&pinctrl0 { + gpio_leds: gpio-leds { + samsung,pins = "gpk-4", "gpk-5", "gpk-6", "gpk-7"; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + gpio_keys: gpio-keys { + samsung,pins = "gpn-0", "gpn-1", "gpn-2", "gpn-3", + "gpn-4", "gpn-5", "gpl-11", "gpl-12"; + samsung,pin-pud = <PIN_PULL_NONE>; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_bus>; + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c08"; + reg = <0x50>; + pagesize = <16>; + }; +}; diff --git a/arch/arm/boot/dts/s3c6410-smdk6410.dts b/arch/arm/boot/dts/s3c6410-smdk6410.dts new file mode 100644 index 0000000..ecf35ec --- /dev/null +++ b/arch/arm/boot/dts/s3c6410-smdk6410.dts @@ -0,0 +1,103 @@ +/* + * Samsung S3C6410 based SMDK6410 board device tree source. + * + * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com> + * + * Device tree source file for SAMSUNG SMDK6410 board which is based on + * Samsung's S3C6410 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#include "s3c6410.dtsi" + +/ { + model = "SAMSUNG SMDK6410 board based on S3C6410"; + compatible = "samsung,mini6410", "samsung,s3c6410"; + + memory { + reg = <0x50000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttySAC0,115200n8 earlyprintk rootwait root=/dev/mmcblk0p1"; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + fin_pll: oscillator@0 { + compatible = "fixed-clock"; + reg = <0>; + clock-frequency = <12000000>; + clock-output-names = "fin_pll"; + #clock-cells = <0>; + }; + + xusbxti: oscillator@1 { + compatible = "fixed-clock"; + reg = <1>; + clock-output-names = "xusbxti"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + }; + + srom-cs1@18000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x18000000 0x8000000>; + ranges; + + ethernet@18000000 { + compatible = "smsc,lan9115"; + reg = <0x18000000 0x10000>; + interrupt-parent = <&gpn>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + phy-mode = "mii"; + reg-io-width = <4>; + smsc,force-internal-phy; + }; + }; +}; + +&sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; + bus-width = <4>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_data>, <&uart0_fctl>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_data>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_data>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_data>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/s3c6410.dtsi b/arch/arm/boot/dts/s3c6410.dtsi new file mode 100644 index 0000000..eb4226b --- /dev/null +++ b/arch/arm/boot/dts/s3c6410.dtsi @@ -0,0 +1,57 @@ +/* + * Samsung's S3C6410 SoC device tree source + * + * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com> + * + * Samsung's S3C6410 SoC device nodes are listed in this file. S3C6410 + * based board files can include this file and provide values for board specfic + * bindings. + * + * Note: This file does not include device nodes for all the controllers in + * S3C6410 SoC. As device tree coverage for S3C6410 increases, additional + * nodes can be added to this file. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include "s3c64xx.dtsi" + +/ { + compatible = "samsung,s3c6410"; + + aliases { + i2c1 = &i2c1; + }; +}; + +&vic0 { + valid-mask = <0xffffff7f>; + valid-wakeup-mask = <0x00200004>; +}; + +&vic1 { + valid-mask = <0xffffffff>; + valid-wakeup-mask = <0x53020000>; +}; + +&soc { + clocks: clock-controller@7e00f000 { + compatible = "samsung,s3c6410-clock"; + reg = <0x7e00f000 0x1000>; + #clock-cells = <1>; + }; + + i2c1: i2c@7f00f000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x7f00f000 0x1000>; + interrupt-parent = <&vic0>; + interrupts = <5>; + clock-names = "i2c"; + clocks = <&clocks PCLK_IIC1>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; +}; diff --git a/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi b/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi new file mode 100644 index 0000000..b1197d8 --- /dev/null +++ b/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi @@ -0,0 +1,687 @@ +/* + * Samsung's S3C64xx SoC series common device tree source + * - pin control-related definitions + * + * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com> + * + * Samsung's S3C64xx SoCs pin banks, pin-mux and pin-config options are + * listed as device tree nodes in this file. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define PIN_PULL_NONE 0 +#define PIN_PULL_DOWN 1 +#define PIN_PULL_UP 2 + +&pinctrl0 { + /* + * Pin banks + */ + + gpa: gpa { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb: gpb { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc: gpc { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd: gpd { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe: gpe { + gpio-controller; + #gpio-cells = <2>; + }; + + gpf: gpf { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpg: gpg { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gph: gph { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpi: gpi { + gpio-controller; + #gpio-cells = <2>; + }; + + gpj: gpj { + gpio-controller; + #gpio-cells = <2>; + }; + + gpk: gpk { + gpio-controller; + #gpio-cells = <2>; + }; + + gpl: gpl { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpm: gpm { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpn: gpn { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpo: gpo { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpp: gpp { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpq: gpq { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + /* + * Pin groups + */ + + uart0_data: uart0-data { + samsung,pins = "gpa-0", "gpa-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + uart0_fctl: uart0-fctl { + samsung,pins = "gpa-2", "gpa-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + uart1_data: uart1-data { + samsung,pins = "gpa-4", "gpa-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + uart1_fctl: uart1-fctl { + samsung,pins = "gpa-6", "gpa-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + uart2_data: uart2-data { + samsung,pins = "gpb-0", "gpb-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + uart3_data: uart3-data { + samsung,pins = "gpb-2", "gpb-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + ext_dma_0: ext-dma-0 { + samsung,pins = "gpb-0", "gpb-1"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + ext_dma_1: ext-dma-1 { + samsung,pins = "gpb-2", "gpb-3"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + irda_data_0: irda-data-0 { + samsung,pins = "gpb-0", "gpb-1"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + irda_data_1: irda-data-1 { + samsung,pins = "gpb-2", "gpb-3"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + irda_sdbw: irda-sdbw { + samsung,pins = "gpb-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + i2c0_bus: i2c0-bus { + samsung,pins = "gpb-5", "gpb-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + }; + + i2c1_bus: i2c1-bus { + /* S3C6410-only */ + samsung,pins = "gpb-2", "gpb-3"; + samsung,pin-function = <6>; + samsung,pin-pud = <PIN_PULL_UP>; + }; + + spi0_bus: spi0-bus { + samsung,pins = "gpc-0", "gpc-1", "gpc-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + }; + + spi0_cs: spi0-cs { + samsung,pins = "gpc-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + spi1_bus: spi1-bus { + samsung,pins = "gpc-4", "gpc-5", "gpc-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + }; + + spi1_cs: spi1-cs { + samsung,pins = "gpc-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd0_cmd: sd0-cmd { + samsung,pins = "gpg-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd0_clk: sd0-clk { + samsung,pins = "gpg-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd0_bus1: sd0-bus1 { + samsung,pins = "gpg-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd0_bus4: sd0-bus4 { + samsung,pins = "gpg-2", "gpg-3", "gpg-4", "gpg-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd0_cd: sd0-cd { + samsung,pins = "gpg-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + }; + + sd1_cmd: sd1-cmd { + samsung,pins = "gph-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd1_clk: sd1-clk { + samsung,pins = "gph-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd1_bus1: sd1-bus1 { + samsung,pins = "gph-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd1_bus4: sd1-bus4 { + samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd1_bus8: sd1-bus8 { + samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5", + "gph-6", "gph-7", "gph-8", "gph-9"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd1_cd: sd1-cd { + samsung,pins = "gpg-6"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_UP>; + }; + + sd2_cmd: sd2-cmd { + samsung,pins = "gpc-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd2_clk: sd2-clk { + samsung,pins = "gpc-5"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd2_bus1: sd2-bus1 { + samsung,pins = "gph-6"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + sd2_bus4: sd2-bus4 { + samsung,pins = "gph-6", "gph-7", "gph-8", "gph-9"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + i2s0_bus: i2s0-bus { + samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + i2s0_cdclk: i2s0-cdclk { + samsung,pins = "gpd-1"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + i2s1_bus: i2s1-bus { + samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + i2s1_cdclk: i2s1-cdclk { + samsung,pins = "gpe-1"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + i2s2_bus: i2s2-bus { + /* S3C6410-only */ + samsung,pins = "gpc-4", "gpc-5", "gpc-6", "gph-6", + "gph-8", "gph-9"; + samsung,pin-function = <5>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + i2s2_cdclk: i2s2-cdclk { + /* S3C6410-only */ + samsung,pins = "gph-7"; + samsung,pin-function = <5>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + pcm0_bus: pcm0-bus { + samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + pcm0_extclk: pcm0-extclk { + samsung,pins = "gpd-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + pcm1_bus: pcm1-bus { + samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + pcm1_extclk: pcm1-extclk { + samsung,pins = "gpe-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + ac97_bus_0: ac97-bus-0 { + samsung,pins = "gpd-0", "gpd-1", "gpd-2", "gpd-3", "gpd-4"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + ac97_bus_1: ac97-bus-1 { + samsung,pins = "gpe-0", "gpe-1", "gpe-2", "gpe-3", "gpe-4"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + cam_port: cam-port { + samsung,pins = "gpf-0", "gpf-1", "gpf-2", "gpf-4", + "gpf-5", "gpf-6", "gpf-7", "gpf-8", + "gpf-9", "gpf-10", "gpf-11", "gpf-12"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + cam_rst: cam-rst { + samsung,pins = "gpf-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + cam_field: cam-field { + /* S3C6410-only */ + samsung,pins = "gpb-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + pwm_extclk: pwm-extclk { + samsung,pins = "gpf-13"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + pwm0_out: pwm0-out { + samsung,pins = "gpf-14"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + pwm1_out: pwm1-out { + samsung,pins = "gpf-15"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + clkout0: clkout-0 { + samsung,pins = "gpf-14"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col0_0: keypad-col0-0 { + samsung,pins = "gph-0"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col1_0: keypad-col1-0 { + samsung,pins = "gph-1"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col2_0: keypad-col2-0 { + samsung,pins = "gph-2"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col3_0: keypad-col3-0 { + samsung,pins = "gph-3"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col4_0: keypad-col4-0 { + samsung,pins = "gph-4"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col5_0: keypad-col5-0 { + samsung,pins = "gph-5"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col6_0: keypad-col6-0 { + samsung,pins = "gph-6"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col7_0: keypad-col7-0 { + samsung,pins = "gph-7"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col0_1: keypad-col0-1 { + samsung,pins = "gpl-0"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col1_1: keypad-col1-1 { + samsung,pins = "gpl-1"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col2_1: keypad-col2-1 { + samsung,pins = "gpl-2"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col3_1: keypad-col3-1 { + samsung,pins = "gpl-3"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col4_1: keypad-col4-1 { + samsung,pins = "gpl-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col5_1: keypad-col5-1 { + samsung,pins = "gpl-5"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col6_1: keypad-col6-1 { + samsung,pins = "gpl-6"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_col7_1: keypad-col7-1 { + samsung,pins = "gpl-7"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row0_0: keypad-row0-0 { + samsung,pins = "gpk-8"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row1_0: keypad-row1-0 { + samsung,pins = "gpk-9"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row2_0: keypad-row2-0 { + samsung,pins = "gpk-10"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row3_0: keypad-row3-0 { + samsung,pins = "gpk-11"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row4_0: keypad-row4-0 { + samsung,pins = "gpk-12"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row5_0: keypad-row5-0 { + samsung,pins = "gpk-13"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row6_0: keypad-row6-0 { + samsung,pins = "gpk-14"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row7_0: keypad-row7-0 { + samsung,pins = "gpk-15"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row0_1: keypad-row0-1 { + samsung,pins = "gpn-0"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row1_1: keypad-row1-1 { + samsung,pins = "gpn-1"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row2_1: keypad-row2-1 { + samsung,pins = "gpn-2"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row3_1: keypad-row3-1 { + samsung,pins = "gpn-3"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row4_1: keypad-row4-1 { + samsung,pins = "gpn-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row5_1: keypad-row5-1 { + samsung,pins = "gpn-5"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row6_1: keypad-row6-1 { + samsung,pins = "gpn-6"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + keypad_row7_1: keypad-row7-1 { + samsung,pins = "gpn-7"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + lcd_ctrl: lcd-ctrl { + samsung,pins = "gpj-8", "gpj-9", "gpj-10", "gpj-11"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + lcd_data16: lcd-data-width16 { + samsung,pins = "gpi-3", "gpi-4", "gpi-5", "gpi-6", + "gpi-7", "gpi-10", "gpi-11", "gpi-12", + "gpi-13", "gpi-14", "gpi-15", "gpj-3", + "gpj-4", "gpj-5", "gpj-6", "gpj-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + lcd_data18: lcd-data-width18 { + samsung,pins = "gpi-2", "gpi-3", "gpi-4", "gpi-5", + "gpi-6", "gpi-7", "gpi-10", "gpi-11", + "gpi-12", "gpi-13", "gpi-14", "gpi-15", + "gpj-2", "gpj-3", "gpj-4", "gpj-5", + "gpj-6", "gpj-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + lcd_data24: lcd-data-width24 { + samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3", + "gpi-4", "gpi-5", "gpi-6", "gpi-7", + "gpi-8", "gpi-9", "gpi-10", "gpi-11", + "gpi-12", "gpi-13", "gpi-14", "gpi-15", + "gpj-0", "gpj-1", "gpj-2", "gpj-3", + "gpj-4", "gpj-5", "gpj-6", "gpj-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; + + hsi_bus: hsi-bus { + samsung,pins = "gpk-0", "gpk-1", "gpk-2", "gpk-3", + "gpk-4", "gpk-5", "gpk-6", "gpk-7"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + }; +}; diff --git a/arch/arm/boot/dts/s3c64xx.dtsi b/arch/arm/boot/dts/s3c64xx.dtsi new file mode 100644 index 0000000..4e3be4d --- /dev/null +++ b/arch/arm/boot/dts/s3c64xx.dtsi @@ -0,0 +1,199 @@ +/* + * Samsung's S3C64xx SoC series common device tree source + * + * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com> + * + * Samsung's S3C64xx SoC series device nodes are listed in this file. + * Particular SoCs from S3C64xx series can include this file and provide + * values for SoCs specfic bindings. + * + * Note: This file does not include device nodes for all the controllers in + * S3C64xx SoCs. As device tree coverage for S3C64xx increases, additional + * nodes can be added to this file. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/clock/samsung,s3c64xx-clock.h> + +/ { + aliases { + i2c0 = &i2c0; + pinctrl0 = &pinctrl0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,arm1176jzf-s", "arm,arm1176"; + reg = <0x0>; + }; + }; + + soc: soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + vic0: interrupt-controller@71200000 { + compatible = "arm,pl192-vic"; + interrupt-controller; + reg = <0x71200000 0x1000>; + #interrupt-cells = <1>; + }; + + vic1: interrupt-controller@71300000 { + compatible = "arm,pl192-vic"; + interrupt-controller; + reg = <0x71300000 0x1000>; + #interrupt-cells = <1>; + }; + + sdhci0: sdhci@7c200000 { + compatible = "samsung,s3c6410-sdhci"; + reg = <0x7c200000 0x100>; + interrupt-parent = <&vic1>; + interrupts = <24>; + clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2"; + clocks = <&clocks HCLK_HSMMC0>, <&clocks HCLK_HSMMC0>, + <&clocks SCLK_MMC0>; + status = "disabled"; + }; + + sdhci1: sdhci@7c300000 { + compatible = "samsung,s3c6410-sdhci"; + reg = <0x7c300000 0x100>; + interrupt-parent = <&vic1>; + interrupts = <25>; + clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2"; + clocks = <&clocks HCLK_HSMMC1>, <&clocks HCLK_HSMMC1>, + <&clocks SCLK_MMC1>; + status = "disabled"; + }; + + sdhci2: sdhci@7c400000 { + compatible = "samsung,s3c6410-sdhci"; + reg = <0x7c400000 0x100>; + interrupt-parent = <&vic1>; + interrupts = <17>; + clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2"; + clocks = <&clocks HCLK_HSMMC2>, <&clocks HCLK_HSMMC2>, + <&clocks SCLK_MMC2>; + status = "disabled"; + }; + + watchdog: watchdog@7e004000 { + compatible = "samsung,s3c2410-wdt"; + reg = <0x7e004000 0x1000>; + interrupt-parent = <&vic0>; + interrupts = <26>; + clock-names = "watchdog"; + clocks = <&clocks PCLK_WDT>; + status = "disabled"; + }; + + i2c0: i2c@7f004000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x7f004000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <18>; + clock-names = "i2c"; + clocks = <&clocks PCLK_IIC0>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + uart0: serial@7f005000 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005000 0x100>; + interrupt-parent = <&vic1>; + interrupts = <5>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + status = "disabled"; + }; + + uart1: serial@7f005400 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005400 0x100>; + interrupt-parent = <&vic1>; + interrupts = <6>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>, + <&clocks SCLK_UART>; + status = "disabled"; + }; + + uart2: serial@7f005800 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005800 0x100>; + interrupt-parent = <&vic1>; + interrupts = <7>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART2>, <&clocks PCLK_UART2>, + <&clocks SCLK_UART>; + status = "disabled"; + }; + + uart3: serial@7f005c00 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005c00 0x100>; + interrupt-parent = <&vic1>; + interrupts = <8>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART3>, <&clocks PCLK_UART3>, + <&clocks SCLK_UART>; + status = "disabled"; + }; + + pwm: pwm@7f006000 { + compatible = "samsung,s3c6400-pwm"; + reg = <0x7f006000 0x1000>; + interrupt-parent = <&vic0>; + interrupts = <23>, <24>, <25>, <27>, <28>; + clock-names = "timers"; + clocks = <&clocks PCLK_PWM>; + samsung,pwm-outputs = <0>, <1>; + #pwm-cells = <3>; + status = "disabled"; + }; + + pinctrl0: pinctrl@7f008000 { + compatible = "samsung,s3c64xx-pinctrl"; + reg = <0x7f008000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <21>; + + pctrl_int_map: pinctrl-interrupt-map { + interrupt-map = <0 &vic0 0>, + <1 &vic0 1>, + <2 &vic1 0>, + <3 &vic1 1>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <1>; + }; + + wakeup-interrupt-controller { + compatible = "samsung,s3c64xx-wakeup-eint"; + interrupts = <0>, <1>, <2>, <3>; + interrupt-parent = <&pctrl_int_map>; + }; + }; + }; +}; + +#include "s3c64xx-pinctrl.dtsi" diff --git a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts index 2122306..8ee06dd 100644 --- a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts +++ b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts @@ -108,6 +108,7 @@ }; &i2c0 { + status = "okay"; as3711@40 { compatible = "ams,as3711"; reg = <0x40>; @@ -183,6 +184,7 @@ &i2c3 { pinctrl-0 = <&i2c3_pins>; pinctrl-names = "default"; + status = "okay"; }; &mmcif { diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi index 3955c76..fcf2688 100644 --- a/arch/arm/boot/dts/sh73a0.dtsi +++ b/arch/arm/boot/dts/sh73a0.dtsi @@ -135,6 +135,7 @@ 0 168 0x4 0 169 0x4 0 170 0x4>; + status = "disabled"; }; i2c1: i2c@e6822000 { @@ -147,6 +148,7 @@ 0 52 0x4 0 53 0x4 0 54 0x4>; + status = "disabled"; }; i2c2: i2c@e6824000 { @@ -159,6 +161,7 @@ 0 172 0x4 0 173 0x4 0 174 0x4>; + status = "disabled"; }; i2c3: i2c@e6826000 { @@ -171,6 +174,7 @@ 0 184 0x4 0 185 0x4 0 186 0x4>; + status = "disabled"; }; i2c4: i2c@e6828000 { @@ -183,6 +187,7 @@ 0 188 0x4 0 189 0x4 0 190 0x4>; + status = "disabled"; }; mmcif: mmcif@e6bd0000 { diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index e273fa9..6d09b8d 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -147,7 +147,7 @@ reg = <0x58>; }; - cfg_s2f_usr0_clk: cfg_s2f_usr0_clk { + cfg_h2f_usr0_clk: cfg_h2f_usr0_clk { #clock-cells = <0>; compatible = "altr,socfpga-perip-clk"; clocks = <&main_pll>; @@ -198,7 +198,7 @@ reg = <0x98>; }; - s2f_usr1_clk: s2f_usr1_clk { + h2f_usr1_clk: h2f_usr1_clk { #clock-cells = <0>; compatible = "altr,socfpga-perip-clk"; clocks = <&periph_pll>; @@ -235,7 +235,7 @@ reg = <0xD0>; }; - s2f_usr2_clk: s2f_usr2_clk { + h2f_usr2_clk: h2f_usr2_clk { #clock-cells = <0>; compatible = "altr,socfpga-perip-clk"; clocks = <&sdram_pll>; @@ -243,197 +243,197 @@ }; }; - mpu_periph_clk: mpu_periph_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mpuclk>; - fixed-divider = <4>; + mpu_periph_clk: mpu_periph_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mpuclk>; + fixed-divider = <4>; }; - mpu_l2_ram_clk: mpu_l2_ram_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mpuclk>; - fixed-divider = <2>; + mpu_l2_ram_clk: mpu_l2_ram_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mpuclk>; + fixed-divider = <2>; }; - l4_main_clk: l4_main_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mainclk>; - clk-gate = <0x60 0>; + l4_main_clk: l4_main_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>; + clk-gate = <0x60 0>; }; - l3_main_clk: l3_main_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mainclk>; + l3_main_clk: l3_main_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>; }; - l3_mp_clk: l3_mp_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mainclk>; - div-reg = <0x64 0 2>; - clk-gate = <0x60 1>; + l3_mp_clk: l3_mp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>; + div-reg = <0x64 0 2>; + clk-gate = <0x60 1>; }; - l3_sp_clk: l3_sp_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mainclk>; - div-reg = <0x64 2 2>; - }; + l3_sp_clk: l3_sp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>; + div-reg = <0x64 2 2>; + }; - l4_mp_clk: l4_mp_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mainclk>, <&per_base_clk>; - div-reg = <0x64 4 3>; - clk-gate = <0x60 2>; + l4_mp_clk: l4_mp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>, <&per_base_clk>; + div-reg = <0x64 4 3>; + clk-gate = <0x60 2>; }; - l4_sp_clk: l4_sp_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&mainclk>, <&per_base_clk>; - div-reg = <0x64 7 3>; - clk-gate = <0x60 3>; + l4_sp_clk: l4_sp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>, <&per_base_clk>; + div-reg = <0x64 7 3>; + clk-gate = <0x60 3>; }; - dbg_at_clk: dbg_at_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&dbg_base_clk>; - div-reg = <0x68 0 2>; - clk-gate = <0x60 4>; + dbg_at_clk: dbg_at_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_base_clk>; + div-reg = <0x68 0 2>; + clk-gate = <0x60 4>; }; - dbg_clk: dbg_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&dbg_base_clk>; - div-reg = <0x68 2 2>; - clk-gate = <0x60 5>; + dbg_clk: dbg_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_base_clk>; + div-reg = <0x68 2 2>; + clk-gate = <0x60 5>; }; - dbg_trace_clk: dbg_trace_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&dbg_base_clk>; - div-reg = <0x6C 0 3>; - clk-gate = <0x60 6>; + dbg_trace_clk: dbg_trace_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_base_clk>; + div-reg = <0x6C 0 3>; + clk-gate = <0x60 6>; }; - dbg_timer_clk: dbg_timer_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&dbg_base_clk>; - clk-gate = <0x60 7>; + dbg_timer_clk: dbg_timer_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_base_clk>; + clk-gate = <0x60 7>; }; - cfg_clk: cfg_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&cfg_s2f_usr0_clk>; - clk-gate = <0x60 8>; + cfg_clk: cfg_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&cfg_h2f_usr0_clk>; + clk-gate = <0x60 8>; }; - s2f_user0_clk: s2f_user0_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&cfg_s2f_usr0_clk>; - clk-gate = <0x60 9>; + h2f_user0_clk: h2f_user0_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&cfg_h2f_usr0_clk>; + clk-gate = <0x60 9>; }; - emac_0_clk: emac_0_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&emac0_clk>; - clk-gate = <0xa0 0>; + emac_0_clk: emac_0_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&emac0_clk>; + clk-gate = <0xa0 0>; }; - emac_1_clk: emac_1_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&emac1_clk>; - clk-gate = <0xa0 1>; + emac_1_clk: emac_1_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&emac1_clk>; + clk-gate = <0xa0 1>; }; - usb_mp_clk: usb_mp_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&per_base_clk>; - clk-gate = <0xa0 2>; - div-reg = <0xa4 0 3>; + usb_mp_clk: usb_mp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 2>; + div-reg = <0xa4 0 3>; }; - spi_m_clk: spi_m_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&per_base_clk>; - clk-gate = <0xa0 3>; - div-reg = <0xa4 3 3>; + spi_m_clk: spi_m_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 3>; + div-reg = <0xa4 3 3>; }; - can0_clk: can0_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&per_base_clk>; - clk-gate = <0xa0 4>; - div-reg = <0xa4 6 3>; + can0_clk: can0_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 4>; + div-reg = <0xa4 6 3>; }; - can1_clk: can1_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&per_base_clk>; - clk-gate = <0xa0 5>; - div-reg = <0xa4 9 3>; + can1_clk: can1_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 5>; + div-reg = <0xa4 9 3>; }; - gpio_db_clk: gpio_db_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&per_base_clk>; - clk-gate = <0xa0 6>; - div-reg = <0xa8 0 24>; + gpio_db_clk: gpio_db_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 6>; + div-reg = <0xa8 0 24>; }; - s2f_user1_clk: s2f_user1_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&s2f_usr1_clk>; - clk-gate = <0xa0 7>; + h2f_user1_clk: h2f_user1_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&h2f_usr1_clk>; + clk-gate = <0xa0 7>; }; - sdmmc_clk: sdmmc_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; - clk-gate = <0xa0 8>; + sdmmc_clk: sdmmc_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; + clk-gate = <0xa0 8>; }; - nand_x_clk: nand_x_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; - clk-gate = <0xa0 9>; + nand_x_clk: nand_x_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; + clk-gate = <0xa0 9>; }; - nand_clk: nand_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; - clk-gate = <0xa0 10>; - fixed-divider = <4>; + nand_clk: nand_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; + clk-gate = <0xa0 10>; + fixed-divider = <4>; }; - qspi_clk: qspi_clk { - #clock-cells = <0>; - compatible = "altr,socfpga-gate-clk"; - clocks = <&f2s_periph_ref_clk>, <&main_qspi_clk>, <&per_qspi_clk>; - clk-gate = <0xa0 11>; + qspi_clk: qspi_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&f2s_periph_ref_clk>, <&main_qspi_clk>, <&per_qspi_clk>; + clk-gate = <0xa0 11>; }; }; }; @@ -473,6 +473,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0xfffec600 0x100>; interrupts = <1 13 0xf04>; + clocks = <&mpu_periph_clk>; }; timer0: timer0@ffc08000 { @@ -516,9 +517,9 @@ }; rstmgr@ffd05000 { - compatible = "altr,rst-mgr"; - reg = <0xffd05000 0x1000>; - }; + compatible = "altr,rst-mgr"; + reg = <0xffd05000 0x1000>; + }; sysmgr@ffd08000 { compatible = "altr,sys-mgr"; diff --git a/arch/arm/boot/dts/socfpga_arria5.dtsi b/arch/arm/boot/dts/socfpga_arria5.dtsi new file mode 100644 index 0000000..a85b404 --- /dev/null +++ b/arch/arm/boot/dts/socfpga_arria5.dtsi @@ -0,0 +1,58 @@ +/* + * Copyright (C) 2013 Altera Corporation <www.altera.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/dts-v1/; +/include/ "socfpga.dtsi" + +/ { + soc { + clkmgr@ffd04000 { + clocks { + osc1 { + clock-frequency = <25000000>; + }; + }; + }; + + serial0@ffc02000 { + clock-frequency = <100000000>; + }; + + serial1@ffc03000 { + clock-frequency = <100000000>; + }; + + sysmgr@ffd08000 { + cpu1-start-addr = <0xffd080c4>; + }; + + timer0@ffc08000 { + clock-frequency = <100000000>; + }; + + timer1@ffc09000 { + clock-frequency = <100000000>; + }; + + timer2@ffd00000 { + clock-frequency = <25000000>; + }; + + timer3@ffd01000 { + clock-frequency = <25000000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/socfpga_arria5_socdk.dts new file mode 100644 index 0000000..5beffb2 --- /dev/null +++ b/arch/arm/boot/dts/socfpga_arria5_socdk.dts @@ -0,0 +1,40 @@ +/* + * Copyright (C) 2013 Altera Corporation <www.altera.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/include/ "socfpga_arria5.dtsi" + +/ { + model = "Altera SOCFPGA Arria V SoC Development Kit"; + compatible = "altr,socfpga-arria5", "altr,socfpga"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; +}; diff --git a/arch/arm/boot/dts/socfpga_cyclone5.dts b/arch/arm/boot/dts/socfpga_cyclone5.dtsi index 973999d..a8716f6 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5.dtsi @@ -19,26 +19,6 @@ /include/ "socfpga.dtsi" / { - model = "Altera SOCFPGA Cyclone V"; - compatible = "altr,socfpga-cyclone5", "altr,socfpga"; - - chosen { - bootargs = "console=ttyS0,57600"; - }; - - memory { - name = "memory"; - device_type = "memory"; - reg = <0x0 0x40000000>; /* 1GB */ - }; - - aliases { - /* this allow the ethaddr uboot environmnet variable contents - * to be added to the gmac1 device tree blob. - */ - ethernet0 = &gmac1; - }; - soc { clkmgr@ffd04000 { clocks { diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts new file mode 100644 index 0000000..2ee52ab --- /dev/null +++ b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts @@ -0,0 +1,40 @@ +/* + * Copyright (C) 2012 Altera Corporation <www.altera.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/include/ "socfpga_cyclone5.dtsi" + +/ { + model = "Altera SOCFPGA Cyclone V SoC Development Kit"; + compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; +}; diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts new file mode 100644 index 0000000..50b99a2 --- /dev/null +++ b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts @@ -0,0 +1,37 @@ +/* + * Copyright (C) 2013 Steffen Trumtrar <s.trumtrar@pengutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/include/ "socfpga_cyclone5.dtsi" + +/ { + model = "Terasic SoCkit"; + compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; +}; + +&gmac1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi index 1c1091e..7da99fe 100644 --- a/arch/arm/boot/dts/ste-dbx5x0.dtsi +++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi @@ -10,6 +10,7 @@ */ #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/mfd/dbx500-prcmu.h> #include "skeleton.dtsi" / { @@ -42,16 +43,56 @@ interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; }; + + clocks { + compatible = "stericsson,u8500-clks"; + + prcmu_clk: prcmu-clock { + #clock-cells = <1>; + }; + + prcc_pclk: prcc-periph-clock { + #clock-cells = <2>; + }; + + prcc_kclk: prcc-kernel-clock { + #clock-cells = <2>; + }; + + rtc_clk: rtc32k-clock { + #clock-cells = <0>; + }; + + smp_twd_clk: smp-twd-clock { + #clock-cells = <0>; + }; + }; + + mtu@a03c6000 { + /* Nomadik System Timer */ + compatible = "st,nomadik-mtu"; + reg = <0xa03c6000 0x1000>; + interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&prcmu_clk PRCMU_TIMCLK>, <&prcc_pclk 6 6>; + clock-names = "timclk", "apb_pclk"; + }; + timer@a0410600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0xa0410600 0x20>; interrupts = <1 13 0x304>; /* IRQ level high per-CPU */ + + clocks = <&smp_twd_clk>; }; rtc@80154000 { compatible = "arm,rtc-pl031", "arm,primecell"; reg = <0x80154000 0x1000>; interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&rtc_clk>; + clock-names = "apb_pclk"; }; gpio0: gpio@8012e000 { @@ -65,6 +106,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <0>; + + clocks = <&prcc_pclk 1 9>; }; gpio1: gpio@8012e080 { @@ -78,6 +121,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <1>; + + clocks = <&prcc_pclk 1 9>; }; gpio2: gpio@8000e000 { @@ -91,6 +136,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <2>; + + clocks = <&prcc_pclk 3 8>; }; gpio3: gpio@8000e080 { @@ -104,6 +151,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <3>; + + clocks = <&prcc_pclk 3 8>; }; gpio4: gpio@8000e100 { @@ -117,6 +166,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <4>; + + clocks = <&prcc_pclk 3 8>; }; gpio5: gpio@8000e180 { @@ -130,6 +181,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <5>; + + clocks = <&prcc_pclk 3 8>; }; gpio6: gpio@8011e000 { @@ -143,6 +196,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <6>; + + clocks = <&prcc_pclk 2 11>; }; gpio7: gpio@8011e080 { @@ -156,6 +211,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <7>; + + clocks = <&prcc_pclk 2 11>; }; gpio8: gpio@a03fe000 { @@ -169,6 +226,8 @@ gpio-controller; #gpio-cells = <2>; gpio-bank = <8>; + + clocks = <&prcc_pclk 5 1>; }; pinctrl { @@ -177,8 +236,7 @@ }; usb_per5@a03e0000 { - compatible = "stericsson,db8500-musb", - "mentor,musb"; + compatible = "stericsson,db8500-musb"; reg = <0xa03e0000 0x10000>; interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "mc"; @@ -210,6 +268,8 @@ "iep_6_14", "oep_6_14", "iep_7_15", "oep_7_15", "iep_8", "oep_8"; + + clocks = <&prcc_pclk 5 0>; }; dma: dma-controller@801C0000 { @@ -220,6 +280,8 @@ #dma-cells = <3>; memcpy-channels = <56 57 58 59 60>; + + clocks = <&prcmu_clk PRCMU_DMACLK>; }; prcmu: prcmu@80157000 { @@ -238,6 +300,13 @@ reg = <0x80157450 0xC>; }; + cpufreq { + compatible = "stericsson,cpufreq-ux500"; + clocks = <&prcmu_clk PRCMU_ARMSS>; + clock-names = "armss"; + status = "disabled"; + }; + thermal@801573c0 { compatible = "stericsson,db8500-thermal"; reg = <0x801573c0 0x40>; @@ -559,65 +628,74 @@ compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; reg = <0x80004000 0x1000>; interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>; - arm,primecell-periphid = <0x180024>; #address-cells = <1>; #size-cells = <0>; v-i2c-supply = <&db8500_vape_reg>; clock-frequency = <400000>; + clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>; + clock-names = "i2cclk", "apb_pclk"; }; i2c@80122000 { compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; reg = <0x80122000 0x1000>; interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; - arm,primecell-periphid = <0x180024>; #address-cells = <1>; #size-cells = <0>; v-i2c-supply = <&db8500_vape_reg>; clock-frequency = <400000>; + + clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>; + clock-names = "i2cclk", "apb_pclk"; }; i2c@80128000 { compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; reg = <0x80128000 0x1000>; interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>; - arm,primecell-periphid = <0x180024>; #address-cells = <1>; #size-cells = <0>; v-i2c-supply = <&db8500_vape_reg>; clock-frequency = <400000>; + + clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>; + clock-names = "i2cclk", "apb_pclk"; }; i2c@80110000 { compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; reg = <0x80110000 0x1000>; interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>; - arm,primecell-periphid = <0x180024>; #address-cells = <1>; #size-cells = <0>; v-i2c-supply = <&db8500_vape_reg>; clock-frequency = <400000>; + + clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>; + clock-names = "i2cclk", "apb_pclk"; }; i2c@8012a000 { compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell"; reg = <0x8012a000 0x1000>; interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>; - arm,primecell-periphid = <0x180024>; #address-cells = <1>; #size-cells = <0>; v-i2c-supply = <&db8500_vape_reg>; clock-frequency = <400000>; + + clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>; + clock-names = "i2cclk", "apb_pclk"; }; ssp@80002000 { @@ -626,7 +704,80 @@ interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - status = "disabled"; + clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>; + clock-names = "ssp0clk", "apb_pclk"; + dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */ + <&dma 8 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + }; + + ssp@80003000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x80003000 0x1000>; + interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>; + clock-names = "ssp1clk", "apb_pclk"; + dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */ + <&dma 9 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + }; + + spi@8011a000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x8011a000 0x1000>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + /* Same clock wired to kernel and pclk */ + clocks = <&prcc_pclk 2 8>, <&prcc_pclk 2 8>; + clock-names = "spi0clk", "apb_pclk"; + dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */ + <&dma 0 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + }; + + spi@80112000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x80112000 0x1000>; + interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + /* Same clock wired to kernel and pclk */ + clocks = <&prcc_pclk 2 2>, <&prcc_pclk 2 2>; + clock-names = "spi1clk", "apb_pclk"; + dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */ + <&dma 35 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + }; + + spi@80111000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x80111000 0x1000>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + /* Same clock wired to kernel and pclk */ + clocks = <&prcc_pclk 2 1>, <&prcc_pclk 2 1>; + clock-names = "spi2clk", "apb_pclk"; + dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */ + <&dma 33 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + }; + + spi@80129000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x80129000 0x1000>; + interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + /* Same clock wired to kernel and pclk */ + clocks = <&prcc_pclk 1 7>, <&prcc_pclk 1 7>; + clock-names = "spi3clk", "apb_pclk"; + dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */ + <&dma 40 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; }; uart@80120000 { @@ -638,6 +789,9 @@ <&dma 13 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; + clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>; + clock-names = "uart", "apb_pclk"; + status = "disabled"; }; @@ -650,6 +804,9 @@ <&dma 12 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; + clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>; + clock-names = "uart", "apb_pclk"; + status = "disabled"; }; @@ -662,6 +819,9 @@ <&dma 11 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; + clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>; + clock-names = "uart", "apb_pclk"; + status = "disabled"; }; @@ -674,6 +834,9 @@ <&dma 29 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; + clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; + clock-names = "sdi", "apb_pclk"; + status = "disabled"; }; @@ -686,6 +849,9 @@ <&dma 32 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; + clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>; + clock-names = "sdi", "apb_pclk"; + status = "disabled"; }; @@ -698,6 +864,9 @@ <&dma 28 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; + clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>; + clock-names = "sdi", "apb_pclk"; + status = "disabled"; }; @@ -705,6 +874,10 @@ compatible = "arm,pl18x", "arm,primecell"; reg = <0x80119000 0x1000>; interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>; + clock-names = "sdi", "apb_pclk"; + status = "disabled"; }; @@ -717,6 +890,9 @@ <&dma 42 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; + clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>; + clock-names = "sdi", "apb_pclk"; + status = "disabled"; }; @@ -724,6 +900,10 @@ compatible = "arm,pl18x", "arm,primecell"; reg = <0x80008000 0x1000>; interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>; + clock-names = "sdi", "apb_pclk"; + status = "disabled"; }; @@ -732,6 +912,10 @@ reg = <0x80123000 0x1000>; interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; v-ape-supply = <&db8500_vape_reg>; + + clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>; + clock-names = "msp", "apb_pclk"; + status = "disabled"; }; @@ -740,6 +924,10 @@ reg = <0x80124000 0x1000>; interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>; v-ape-supply = <&db8500_vape_reg>; + + clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>; + clock-names = "msp", "apb_pclk"; + status = "disabled"; }; @@ -749,6 +937,10 @@ reg = <0x80117000 0x1000>; interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>; v-ape-supply = <&db8500_vape_reg>; + + clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>; + clock-names = "msp", "apb_pclk"; + status = "disabled"; }; @@ -757,6 +949,10 @@ reg = <0x80125000 0x1000>; interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>; v-ape-supply = <&db8500_vape_reg>; + + clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>; + clock-names = "msp", "apb_pclk"; + status = "disabled"; }; @@ -772,7 +968,7 @@ cpufreq-cooling { compatible = "stericsson,db8500-cpufreq-cooling"; status = "disabled"; - }; + }; vmmci: regulator-gpio { compatible = "regulator-gpio"; @@ -797,6 +993,7 @@ interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>; v-ape-supply = <&db8500_vape_reg>; + clocks = <&prcc_pclk 6 1>; }; hash@a03c2000 { @@ -804,6 +1001,7 @@ reg = <0xa03c2000 0x1000>; v-ape-supply = <&db8500_vape_reg>; + clocks = <&prcc_pclk 6 2>; }; }; }; diff --git a/arch/arm/boot/dts/ste-stuib.dtsi b/arch/arm/boot/dts/ste-href-stuib.dtsi index 524e332..76704ec 100644 --- a/arch/arm/boot/dts/ste-stuib.dtsi +++ b/arch/arm/boot/dts/ste-href-stuib.dtsi @@ -57,7 +57,6 @@ bu21013_tp@5c { compatible = "rohm,bu21013_tp"; reg = <0x5c>; - touch-gpio = <&gpio2 20 0x4>; avdd-supply = <&ab8500_ldo_aux1_reg>; rohm,touch-max-x = <384>; @@ -68,7 +67,6 @@ bu21013_tp@5d { compatible = "rohm,bu21013_tp"; reg = <0x5d>; - touch-gpio = <&gpio2 20 0x4>; avdd-supply = <&ab8500_ldo_aux1_reg>; rohm,touch-max-x = <384>; diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi new file mode 100644 index 0000000..76d3ef1 --- /dev/null +++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi @@ -0,0 +1,41 @@ +/* + * Copyright 2012 ST-Ericsson AB + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + * + * Device Tree for the TVK1281618 UIB + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + soc { + /* Add Synaptics touch screen, TC35892 keypad etc here */ + i2c@80004000 { + tc3589x@44 { + compatible = "tc3589x"; + reg = <0x44>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + + tc3589x_gpio { + compatible = "tc3589x-gpio"; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi index 370e03f..aa3f020 100644 --- a/arch/arm/boot/dts/ste-href.dtsi +++ b/arch/arm/boot/dts/ste-href.dtsi @@ -41,28 +41,6 @@ status = "okay"; }; - i2c@80004000 { - tc3589x@42 { - compatible = "tc3589x"; - reg = <0x42>; - interrupt-parent = <&gpio6>; - interrupts = <25 IRQ_TYPE_EDGE_RISING>; - - interrupt-controller; - #interrupt-cells = <2>; - - tc3589x_gpio: tc3589x_gpio { - compatible = "tc3589x-gpio"; - interrupts = <0 IRQ_TYPE_EDGE_RISING>; - - interrupt-controller; - #interrupt-cells = <2>; - gpio-controller; - #gpio-cells = <2>; - }; - }; - }; - i2c@80128000 { lp5521@33 { compatible = "national,lp5521"; @@ -72,6 +50,7 @@ chan0 { led-cur = /bits/ 8 <0x2f>; max-cur = /bits/ 8 <0x5f>; + linux,default-trigger = "heartbeat"; }; chan1 { led-cur = /bits/ 8 <0x2f>; @@ -102,7 +81,7 @@ }; bh1780@29 { compatible = "rohm,bh1780gli"; - reg = <0x33>; + reg = <0x29>; }; }; @@ -167,89 +146,11 @@ }; prcmu@80157000 { - db8500-prcmu-regulators { - db8500_vape_reg: db8500_vape { - regulator-name = "db8500-vape"; - }; - - db8500_varm_reg: db8500_varm { - regulator-name = "db8500-varm"; - }; - - db8500_vmodem_reg: db8500_vmodem { - regulator-name = "db8500-vmodem"; - }; - - db8500_vpll_reg: db8500_vpll { - regulator-name = "db8500-vpll"; - }; - - db8500_vsmps1_reg: db8500_vsmps1 { - regulator-name = "db8500-vsmps1"; - }; - - db8500_vsmps2_reg: db8500_vsmps2 { - regulator-name = "db8500-vsmps2"; - }; - - db8500_vsmps3_reg: db8500_vsmps3 { - regulator-name = "db8500-vsmps3"; - }; - - db8500_vrf1_reg: db8500_vrf1 { - regulator-name = "db8500-vrf1"; - }; - - db8500_sva_mmdsp_reg: db8500_sva_mmdsp { - regulator-name = "db8500-sva-mmdsp"; - }; - - db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret { - regulator-name = "db8500-sva-mmdsp-ret"; - }; - - db8500_sva_pipe_reg: db8500_sva_pipe { - regulator-name = "db8500_sva_pipe"; - }; - - db8500_sia_mmdsp_reg: db8500_sia_mmdsp { - regulator-name = "db8500_sia_mmdsp"; - }; - - db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret { - regulator-name = "db8500-sia-mmdsp-ret"; - }; - - db8500_sia_pipe_reg: db8500_sia_pipe { - regulator-name = "db8500-sia-pipe"; - }; - - db8500_sga_reg: db8500_sga { - regulator-name = "db8500-sga"; - }; - - db8500_b2r2_mcde_reg: db8500_b2r2_mcde { - regulator-name = "db8500-b2r2-mcde"; - }; - - db8500_esram12_reg: db8500_esram12 { - regulator-name = "db8500-esram12"; - }; - - db8500_esram12_ret_reg: db8500_esram12_ret { - regulator-name = "db8500-esram12-ret"; - }; - - db8500_esram34_reg: db8500_esram34 { - regulator-name = "db8500-esram34"; + ab8500 { + ab8500-gpio { + compatible = "stericsson,ab8500-gpio"; }; - db8500_esram34_ret_reg: db8500_esram34_ret { - regulator-name = "db8500-esram34-ret"; - }; - }; - - ab8500 { ab8500-regulators { ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { regulator-name = "V-DISPLAY"; diff --git a/arch/arm/boot/dts/ste-hrefprev60-stuib.dts b/arch/arm/boot/dts/ste-hrefprev60-stuib.dts new file mode 100644 index 0000000..2b1cb5b --- /dev/null +++ b/arch/arm/boot/dts/ste-hrefprev60-stuib.dts @@ -0,0 +1,34 @@ +/* + * Copyright 2012 ST-Ericsson AB + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "ste-hrefprev60.dtsi" +#include "ste-href-stuib.dtsi" + +/ { + model = "ST-Ericsson HREF (pre-v60) and ST UIB"; + compatible = "st-ericsson,mop500", "st-ericsson,u8500"; + + soc { + /* Reset line for the BU21013 touchscreen */ + i2c@80110000 { + /* Only one of these will be used */ + bu21013_tp@5c { + touch-gpio = <&gpio2 12 0x4>; + reset-gpio = <&tc3589x_gpio 13 0x4>; + }; + bu21013_tp@5d { + touch-gpio = <&gpio2 12 0x4>; + reset-gpio = <&tc3589x_gpio 13 0x4>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts new file mode 100644 index 0000000..59523f8 --- /dev/null +++ b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts @@ -0,0 +1,19 @@ +/* + * Copyright 2012 ST-Ericsson AB + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "ste-hrefprev60.dtsi" +#include "ste-href-tvk1281618.dtsi" + +/ { + model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB"; + compatible = "st-ericsson,mop500", "st-ericsson,u8500"; +}; diff --git a/arch/arm/boot/dts/ste-hrefprev60.dts b/arch/arm/boot/dts/ste-hrefprev60.dtsi index d8d3b99..b2cd7bc 100644 --- a/arch/arm/boot/dts/ste-hrefprev60.dts +++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi @@ -7,17 +7,14 @@ * * http://www.opensource.org/licenses/gpl-license.html * http://www.gnu.org/copyleft/gpl.html + * + * Device Tree for the HREF+ prior to the v60 variant. */ -/dts-v1/; #include "ste-dbx5x0.dtsi" #include "ste-href.dtsi" -#include "ste-stuib.dtsi" / { - model = "ST-Ericsson HREF (pre-v60) platform with Device Tree"; - compatible = "st-ericsson,mop500", "st-ericsson,u8500"; - gpio_keys { button@1 { gpios = <&tc3589x_gpio 7 0x4>; @@ -25,24 +22,30 @@ }; soc { - prcmu@80157000 { - ab8500@5 { - ab8500-gpio { - compatible = "stericsson,ab8500-gpio"; - }; - }; - }; - i2c@80004000 { tps61052@33 { compatible = "tps61052"; reg = <0x33>; }; - }; - i2c@80110000 { - bu21013_tp@5c { - reset-gpio = <&tc3589x_gpio 13 0x4>; + tc3589x@42 { + compatible = "tc3589x"; + reg = <0x42>; + interrupt-parent = <&gpio6>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + + tc3589x_gpio: tc3589x_gpio { + compatible = "tc3589x-gpio"; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; }; }; diff --git a/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts b/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts new file mode 100644 index 0000000..8c6a2de --- /dev/null +++ b/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts @@ -0,0 +1,36 @@ +/* + * Copyright 2012 ST-Ericsson AB + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + * + * Device Tree for the HREF version 60 or later with the ST UIB + */ + +/dts-v1/; +#include "ste-hrefv60plus.dtsi" +#include "ste-href-stuib.dtsi" + +/ { + model = "ST-Ericsson HREF (v60+) and ST UIB"; + compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; + + soc { + /* Reset line for the BU21013 touchscreen */ + i2c@80110000 { + /* Only one of these will be used */ + bu21013_tp@5c { + touch-gpio = <&gpio2 20 0x4>; + reset-gpio = <&gpio4 17 0x4>; + }; + bu21013_tp@5d { + touch-gpio = <&gpio2 20 0x4>; + reset-gpio = <&gpio4 17 0x4>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts new file mode 100644 index 0000000..d53cccd --- /dev/null +++ b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts @@ -0,0 +1,21 @@ +/* + * Copyright 2012 ST-Ericsson AB + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + * + * Device Tree for the HREF version 60 or later with the TVK1281618 UIB + */ + +/dts-v1/; +#include "ste-hrefv60plus.dtsi" +#include "ste-href-tvk1281618.dtsi" + +/ { + model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB"; + compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; +}; diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dts b/arch/arm/boot/dts/ste-hrefv60plus.dts deleted file mode 100644 index 6e52ebb..0000000 --- a/arch/arm/boot/dts/ste-hrefv60plus.dts +++ /dev/null @@ -1,210 +0,0 @@ -/* - * Copyright 2012 ST-Ericsson AB - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ - -/dts-v1/; -#include "ste-dbx5x0.dtsi" -#include "ste-href.dtsi" -#include "ste-stuib.dtsi" - -/ { - model = "ST-Ericsson HREF (v60+) platform with Device Tree"; - compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; - - gpio_keys { - button@1 { - gpios = <&gpio6 25 0x4>; - }; - }; - - soc { - i2c@80110000 { - bu21013_tp@0x5c { - reset-gpio = <&gpio4 15 0x4>; - }; - }; - - // External Micro SD slot - sdi0_per1@80126000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <4>; - mmc-cap-sd-highspeed; - mmc-cap-mmc-highspeed; - vmmc-supply = <&ab8500_ldo_aux3_reg>; - - cd-gpios = <&tc3589x_gpio 3 0x4>; - - status = "okay"; - }; - - // WLAN SDIO channel - sdi1_per2@80118000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <4>; - - status = "okay"; - }; - - // PoP:ed eMMC - sdi2_per3@80005000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <8>; - mmc-cap-mmc-highspeed; - - status = "okay"; - }; - - // On-board eMMC - sdi4_per2@80114000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <8>; - mmc-cap-mmc-highspeed; - vmmc-supply = <&ab8500_ldo_aux2_reg>; - - status = "okay"; - }; - - prcmu@80157000 { - db8500-prcmu-regulators { - db8500_vape_reg: db8500_vape { - regulator-name = "db8500-vape"; - }; - - db8500_varm_reg: db8500_varm { - regulator-name = "db8500-varm"; - }; - - db8500_vmodem_reg: db8500_vmodem { - regulator-name = "db8500-vmodem"; - }; - - db8500_vpll_reg: db8500_vpll { - regulator-name = "db8500-vpll"; - }; - - db8500_vsmps1_reg: db8500_vsmps1 { - regulator-name = "db8500-vsmps1"; - }; - - db8500_vsmps2_reg: db8500_vsmps2 { - regulator-name = "db8500-vsmps2"; - }; - - db8500_vsmps3_reg: db8500_vsmps3 { - regulator-name = "db8500-vsmps3"; - }; - - db8500_vrf1_reg: db8500_vrf1 { - regulator-name = "db8500-vrf1"; - }; - - db8500_sva_mmdsp_reg: db8500_sva_mmdsp { - regulator-name = "db8500-sva-mmdsp"; - }; - - db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret { - regulator-name = "db8500-sva-mmdsp-ret"; - }; - - db8500_sva_pipe_reg: db8500_sva_pipe { - regulator-name = "db8500_sva_pipe"; - }; - - db8500_sia_mmdsp_reg: db8500_sia_mmdsp { - regulator-name = "db8500_sia_mmdsp"; - }; - - db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret { - regulator-name = "db8500-sia-mmdsp-ret"; - }; - - db8500_sia_pipe_reg: db8500_sia_pipe { - regulator-name = "db8500-sia-pipe"; - }; - - db8500_sga_reg: db8500_sga { - regulator-name = "db8500-sga"; - }; - - db8500_b2r2_mcde_reg: db8500_b2r2_mcde { - regulator-name = "db8500-b2r2-mcde"; - }; - - db8500_esram12_reg: db8500_esram12 { - regulator-name = "db8500-esram12"; - }; - - db8500_esram12_ret_reg: db8500_esram12_ret { - regulator-name = "db8500-esram12-ret"; - }; - - db8500_esram34_reg: db8500_esram34 { - regulator-name = "db8500-esram34"; - }; - - db8500_esram34_ret_reg: db8500_esram34_ret { - regulator-name = "db8500-esram34-ret"; - }; - }; - - ab8500 { - ab8500-regulators { - ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { - regulator-name = "V-DISPLAY"; - }; - - ab8500_ldo_aux2_reg: ab8500_ldo_aux2 { - regulator-name = "V-eMMC1"; - }; - - ab8500_ldo_aux3_reg: ab8500_ldo_aux3 { - regulator-name = "V-MMC-SD"; - }; - - ab8500_ldo_intcore_reg: ab8500_ldo_intcore { - regulator-name = "V-INTCORE"; - }; - - ab8500_ldo_tvout_reg: ab8500_ldo_tvout { - regulator-name = "V-TVOUT"; - }; - - ab8500_ldo_usb_reg: ab8500_ldo_usb { - regulator-name = "dummy"; - }; - - ab8500_ldo_audio_reg: ab8500_ldo_audio { - regulator-name = "V-AUD"; - }; - - ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 { - regulator-name = "V-AMIC1"; - }; - - ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 { - regulator-name = "V-AMIC2"; - }; - - ab8500_ldo_dmic_reg: ab8500_ldo_dmic { - regulator-name = "V-DMIC"; - }; - - ab8500_ldo_ana_reg: ab8500_ldo_ana { - regulator-name = "V-CSI/DSI"; - }; - }; - }; - }; - }; -}; diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi new file mode 100644 index 0000000..aed511b --- /dev/null +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -0,0 +1,70 @@ +/* + * Copyright 2012 ST-Ericsson AB + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include "ste-dbx5x0.dtsi" +#include "ste-href.dtsi" + +/ { + model = "ST-Ericsson HREF (v60+) platform with Device Tree"; + compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; + + gpio_keys { + button@1 { + gpios = <&gpio5 25 0x4>; + }; + }; + + soc { + // External Micro SD slot + sdi0_per1@80126000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <100000000>; + bus-width = <4>; + mmc-cap-sd-highspeed; + mmc-cap-mmc-highspeed; + vmmc-supply = <&ab8500_ldo_aux3_reg>; + + cd-gpios = <&gpio2 31 0x4>; // 95 + + status = "okay"; + }; + + // WLAN SDIO channel + sdi1_per2@80118000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <100000000>; + bus-width = <4>; + + status = "okay"; + }; + + // PoP:ed eMMC + sdi2_per3@80005000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <100000000>; + bus-width = <8>; + mmc-cap-mmc-highspeed; + + status = "okay"; + }; + + // On-board eMMC + sdi4_per2@80114000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <100000000>; + bus-width = <8>; + mmc-cap-mmc-highspeed; + vmmc-supply = <&ab8500_ldo_aux2_reg>; + + status = "okay"; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index f1fc128..f0b39f8 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -111,12 +111,13 @@ vdd33a-supply = <&en_3v3_reg>; vddvario-supply = <&db8500_vape_reg>; - reg-shift = <1>; reg-io-width = <2>; smsc,force-internal-phy; smsc,irq-active-high; smsc,irq-push-pull; + + clocks = <&prcc_pclk 3 0>; }; }; @@ -170,86 +171,8 @@ }; prcmu@80157000 { - db8500-prcmu-regulators { - db8500_vape_reg: db8500_vape { - regulator-name = "db8500-vape"; - }; - - db8500_varm_reg: db8500_varm { - regulator-name = "db8500-varm"; - }; - - db8500_vmodem_reg: db8500_vmodem { - regulator-name = "db8500-vmodem"; - }; - - db8500_vpll_reg: db8500_vpll { - regulator-name = "db8500-vpll"; - }; - - db8500_vsmps1_reg: db8500_vsmps1 { - regulator-name = "db8500-vsmps1"; - }; - - db8500_vsmps2_reg: db8500_vsmps2 { - regulator-name = "db8500-vsmps2"; - }; - - db8500_vsmps3_reg: db8500_vsmps3 { - regulator-name = "db8500-vsmps3"; - }; - - db8500_vrf1_reg: db8500_vrf1 { - regulator-name = "db8500-vrf1"; - }; - - db8500_sva_mmdsp_reg: db8500_sva_mmdsp { - regulator-name = "db8500-sva-mmdsp"; - }; - - db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret { - regulator-name = "db8500-sva-mmdsp-ret"; - }; - - db8500_sva_pipe_reg: db8500_sva_pipe { - regulator-name = "db8500_sva_pipe"; - }; - - db8500_sia_mmdsp_reg: db8500_sia_mmdsp { - regulator-name = "db8500_sia_mmdsp"; - }; - - db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret { - regulator-name = "db8500-sia-mmdsp-ret"; - }; - - db8500_sia_pipe_reg: db8500_sia_pipe { - regulator-name = "db8500-sia-pipe"; - }; - - db8500_sga_reg: db8500_sga { - regulator-name = "db8500-sga"; - }; - - db8500_b2r2_mcde_reg: db8500_b2r2_mcde { - regulator-name = "db8500-b2r2-mcde"; - }; - - db8500_esram12_reg: db8500_esram12 { - regulator-name = "db8500-esram12"; - }; - - db8500_esram12_ret_reg: db8500_esram12_ret { - regulator-name = "db8500-esram12-ret"; - }; - - db8500_esram34_reg: db8500_esram34 { - regulator-name = "db8500-esram34"; - }; - - db8500_esram34_ret_reg: db8500_esram34_ret { - regulator-name = "db8500-esram34-ret"; - }; + cpufreq { + status = "okay"; }; thermal@801573c0 { diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi index c32770a..319cc6b 100644 --- a/arch/arm/boot/dts/sun4i-a10.dtsi +++ b/arch/arm/boot/dts/sun4i-a10.dtsi @@ -266,6 +266,11 @@ reg = <0x01c20c90 0x10>; }; + sid: eeprom@01c23800 { + compatible = "allwinner,sun4i-sid"; + reg = <0x01c23800 0x10>; + }; + uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi index 3b4a057..5247674 100644 --- a/arch/arm/boot/dts/sun5i-a10s.dtsi +++ b/arch/arm/boot/dts/sun5i-a10s.dtsi @@ -255,6 +255,11 @@ reg = <0x01c20c90 0x10>; }; + sid: eeprom@01c23800 { + compatible = "allwinner,sun4i-sid"; + reg = <0x01c23800 0x10>; + }; + uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi index f6091dc..ce8ef2a 100644 --- a/arch/arm/boot/dts/sun5i-a13.dtsi +++ b/arch/arm/boot/dts/sun5i-a13.dtsi @@ -222,6 +222,11 @@ reg = <0x01c20c90 0x10>; }; + sid: eeprom@01c23800 { + compatible = "allwinner,sun4i-sid"; + reg = <0x01c23800 0x10>; + }; + uart1: serial@01c28400 { compatible = "snps,dw-apb-uart"; reg = <0x01c28400 0x400>; diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index f244f5f..c1751a6 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -175,7 +175,7 @@ apb2_gates: apb2_gates@01c2006c { #clock-cells = <1>; compatible = "allwinner,sun6i-a31-apb2-gates-clk"; - reg = <0x01c2006c 0x8>; + reg = <0x01c2006c 0x4>; clocks = <&apb2>; clock-output-names = "apb2_i2c0", "apb2_i2c1", "apb2_i2c2", "apb2_i2c3", "apb2_uart0", diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts index 15e625e..5c51cb8 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts @@ -48,6 +48,18 @@ pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + }; + + i2c1: i2c@01c2b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + }; }; leds { diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts new file mode 100644 index 0000000..8a1009d --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts @@ -0,0 +1,63 @@ +/* + * Copyright 2013 Oliver Schinagl + * + * Oliver Schinagl <oliver@schinagl.nl> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun7i-a20.dtsi" + +/ { + model = "Cubietech Cubietruck"; + compatible = "cubietech,cubietruck", "allwinner,sun7i-a20"; + + soc@01c00000 { + pinctrl@01c20800 { + led_pins_cubietruck: led_pins@0 { + allwinner,pins = "PH7", "PH11", "PH20", "PH21"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_cubietruck>; + + blue { + label = "cubietruck:blue:usr"; + gpios = <&pio 7 21 0>; + }; + + orange { + label = "cubietruck:orange:usr"; + gpios = <&pio 7 20 0>; + }; + + white { + label = "cubietruck:white:usr"; + gpios = <&pio 7 11 0>; + }; + + green { + label = "cubietruck:green:usr"; + gpios = <&pio 7 7 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts index 9e77855..ead3013 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts @@ -60,6 +60,24 @@ pinctrl-0 = <&uart7_pins_a>; status = "okay"; }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + }; + + i2c1: i2c@01c2b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + }; + + i2c2: i2c@01c2b400 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + }; }; leds { diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index 80559cb..e46cfed 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -215,6 +215,27 @@ allwinner,pull = <0>; }; + i2c0_pins_a: i2c0@0 { + allwinner,pins = "PB0", "PB1"; + allwinner,function = "i2c0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c1_pins_a: i2c1@0 { + allwinner,pins = "PB18", "PB19"; + allwinner,function = "i2c1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c2_pins_a: i2c2@0 { + allwinner,pins = "PB20", "PB21"; + allwinner,function = "i2c2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + emac_pins_a: emac0@0 { allwinner,pins = "PA0", "PA1", "PA2", "PA3", "PA4", "PA5", "PA6", @@ -244,6 +265,11 @@ reg = <0x01c20c90 0x10>; }; + sid: eeprom@01c23800 { + compatible = "allwinner,sun7i-a20-sid"; + reg = <0x01c23800 0x200>; + }; + uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; @@ -324,6 +350,51 @@ status = "disabled"; }; + i2c0: i2c@01c2ac00 { + compatible = "allwinner,sun4i-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = <0 7 1>; + clocks = <&apb1_gates 0>; + clock-frequency = <100000>; + status = "disabled"; + }; + + i2c1: i2c@01c2b000 { + compatible = "allwinner,sun4i-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = <0 8 1>; + clocks = <&apb1_gates 1>; + clock-frequency = <100000>; + status = "disabled"; + }; + + i2c2: i2c@01c2b400 { + compatible = "allwinner,sun4i-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = <0 9 1>; + clocks = <&apb1_gates 2>; + clock-frequency = <100000>; + status = "disabled"; + }; + + i2c3: i2c@01c2b800 { + compatible = "allwinner,sun4i-i2c"; + reg = <0x01c2b800 0x400>; + interrupts = <0 88 1>; + clocks = <&apb1_gates 3>; + clock-frequency = <100000>; + status = "disabled"; + }; + + i2c4: i2c@01c2bc00 { + compatible = "allwinner,sun4i-i2c"; + reg = <0x01c2bc00 0x400>; + interrupts = <0 89 1>; + clocks = <&apb1_gates 15>; + clock-frequency = <100000>; + status = "disabled"; + }; + gic: interrupt-controller@01c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>, diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts index 6023028..cb5ec23 100644 --- a/arch/arm/boot/dts/tegra114-dalmore.dts +++ b/arch/arm/boot/dts/tegra114-dalmore.dts @@ -1,5 +1,6 @@ /dts-v1/; +#include <dt-bindings/input/input.h> #include "tegra114.dtsi" / { @@ -738,6 +739,14 @@ realtek,ldo1-en-gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; }; + + temperature-sensor@4c { + compatible = "onnn,nct1008"; + reg = <0x4c>; + vcc-supply = <&palmas_ldo6_reg>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>; + }; }; i2c@7000d000 { @@ -947,7 +956,7 @@ regulator-max-microvolt = <1800000>; }; - ldo6 { + palmas_ldo6_reg: ldo6 { regulator-name = "vdd-sensor-2v85"; regulator-min-microvolt = <2850000>; regulator-max-microvolt = <2850000>; @@ -1011,6 +1020,19 @@ interrupt-parent = <&palmas>; interrupts = <8 0>; }; + + pinmux { + compatible = "ti,tps65913-pinctrl"; + pinctrl-names = "default"; + pinctrl-0 = <&palmas_default>; + + palmas_default: pinmux { + pin_gpio6 { + pins = "gpio6"; + function = "gpio"; + }; + }; + }; }; }; @@ -1081,26 +1103,26 @@ home { label = "Home"; gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>; - linux,code = <102>; /* KEY_HOME */ + linux,code = <KEY_HOME>; }; power { label = "Power"; gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>; - linux,code = <116>; /* KEY_POWER */ + linux,code = <KEY_POWER>; gpio-key,wakeup; }; volume_down { label = "Volume Down"; gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>; - linux,code = <114>; /* KEY_VOLUMEDOWN */ + linux,code = <KEY_VOLUMEDOWN>; }; volume_up { label = "Volume Up"; gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>; - linux,code = <115>; /* KEY_VOLUMEUP */ + linux,code = <KEY_VOLUMEUP>; }; }; diff --git a/arch/arm/boot/dts/tegra114.dtsi b/arch/arm/boot/dts/tegra114.dtsi index 2905145..8d42787 100644 --- a/arch/arm/boot/dts/tegra114.dtsi +++ b/arch/arm/boot/dts/tegra114.dtsi @@ -318,9 +318,9 @@ iommu { compatible = "nvidia,tegra114-smmu", "nvidia,tegra30-smmu"; - reg = <0x7000f010 0x02c - 0x7000f1f0 0x010 - 0x7000f228 0x074>; + reg = <0x70019010 0x02c + 0x700191f0 0x010 + 0x70019228 0x074>; nvidia,#asids = <4>; dma-window = <0 0x40000000>; nvidia,swgroups = <0x18659fe>; diff --git a/arch/arm/boot/dts/tegra124-venice2.dts b/arch/arm/boot/dts/tegra124-venice2.dts new file mode 100644 index 0000000..431d67a --- /dev/null +++ b/arch/arm/boot/dts/tegra124-venice2.dts @@ -0,0 +1,27 @@ +/dts-v1/; + +#include "tegra124.dtsi" + +/ { + model = "NVIDIA Tegra124 Venice2"; + compatible = "nvidia,venice2", "nvidia,tegra124"; + + memory { + reg = <0x80000000 0x80000000>; + }; + + serial@70006000 { + status = "okay"; + }; + + pmc@7000e400 { + nvidia,invert-interrupt; + nvidia,suspend-mode = <1>; + nvidia,cpu-pwr-good-time = <500>; + nvidia,cpu-pwr-off-time = <300>; + nvidia,core-pwr-good-time = <641 3845>; + nvidia,core-pwr-off-time = <61036>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; + }; +}; diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi new file mode 100644 index 0000000..b741300 --- /dev/null +++ b/arch/arm/boot/dts/tegra124.dtsi @@ -0,0 +1,149 @@ +#include <dt-bindings/gpio/tegra-gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +#include "skeleton.dtsi" + +/ { + compatible = "nvidia,tegra124"; + interrupt-parent = <&gic>; + + gic: interrupt-controller@50041000 { + compatible = "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x50041000 0x1000>, + <0x50042000 0x1000>, + <0x50044000 0x2000>, + <0x50046000 0x2000>; + interrupts = <GIC_PPI 9 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + timer@60005000 { + compatible = "nvidia,tegra124-timer", "nvidia,tegra20-timer"; + reg = <0x60005000 0x400>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpio: gpio@6000d000 { + compatible = "nvidia,tegra124-gpio", "nvidia,tegra30-gpio"; + reg = <0x6000d000 0x1000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; + }; + + /* + * There are two serial driver i.e. 8250 based simple serial + * driver and APB DMA based serial driver for higher baudrate + * and performace. To enable the 8250 based driver, the compatible + * is "nvidia,tegra124-uart", "nvidia,tegra20-uart" and to enable + * the APB DMA based serial driver, the comptible is + * "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart". + */ + serial@70006000 { + compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; + reg = <0x70006000 0x40>; + reg-shift = <2>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + serial@70006040 { + compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; + reg = <0x70006040 0x40>; + reg-shift = <2>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + serial@70006200 { + compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; + reg = <0x70006200 0x40>; + reg-shift = <2>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + serial@70006300 { + compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; + reg = <0x70006300 0x40>; + reg-shift = <2>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + serial@70006400 { + compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; + reg = <0x70006400 0x40>; + reg-shift = <2>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + rtc@7000e000 { + compatible = "nvidia,tegra124-rtc", "nvidia,tegra20-rtc"; + reg = <0x7000e000 0x100>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + }; + + pmc@7000e400 { + compatible = "nvidia,tegra124-pmc"; + reg = <0x7000e400 0x400>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <1>; + }; + + cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <2>; + }; + + cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <3>; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; +}; diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi index e19dbf2..5ea7dfa 100644 --- a/arch/arm/boot/dts/tegra30-cardhu.dtsi +++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi @@ -294,9 +294,10 @@ }; }; - nct1008 { + temperature-sensor@4c { compatible = "onnn,nct1008"; reg = <0x4c>; + vcc-supply = <&sys_3v3_reg>; interrupt-parent = <&gpio>; interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>; }; diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index 0022c12..2bd55cf 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -136,12 +136,13 @@ gr3d { compatible = "nvidia,tegra30-gr3d"; reg = <0x54180000 0x00040000>; - clocks = <&tegra_car 24 &tegra_car 98>; + clocks = <&tegra_car TEGRA30_CLK_GR3D + &tegra_car TEGRA30_CLK_GR3D2>; clock-names = "3d", "3d2"; }; dc@54200000 { - compatible = "nvidia,tegra30-dc"; + compatible = "nvidia,tegra30-dc", "nvidia,tegra20-dc"; reg = <0x54200000 0x00040000>; interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA30_CLK_DISP1>, diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi index 5aba238..fb1b2ec 100644 --- a/arch/arm/boot/dts/twl4030.dtsi +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -23,6 +23,22 @@ compatible = "ti,twl4030-wdt"; }; + vaux1: regulator-vaux1 { + compatible = "ti,twl4030-vaux1"; + }; + + vaux2: regulator-vaux2 { + compatible = "ti,twl4030-vaux2"; + }; + + vaux3: regulator-vaux3 { + compatible = "ti,twl4030-vaux3"; + }; + + vaux4: regulator-vaux4 { + compatible = "ti,twl4030-vaux4"; + }; + vcc: regulator-vdd1 { compatible = "ti,twl4030-vdd1"; regulator-min-microvolt = <600000>; @@ -35,10 +51,20 @@ regulator-max-microvolt = <1800000>; }; - vpll2: regulator-vpll2 { - compatible = "ti,twl4030-vpll2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; + vio: regulator-vio { + compatible = "ti,twl4030-vio"; + }; + + vintana1: regulator-vintana1 { + compatible = "ti,twl4030-vintana1"; + }; + + vintana2: regulator-vintana2 { + compatible = "ti,twl4030-vintana2"; + }; + + vintdig: regulator-vintdig { + compatible = "ti,twl4030-vintdig"; }; vmmc1: regulator-vmmc1 { @@ -65,6 +91,16 @@ compatible = "ti,twl4030-vusb3v1"; }; + vpll1: regulator-vpll1 { + compatible = "ti,twl4030-vpll1"; + }; + + vpll2: regulator-vpll2 { + compatible = "ti,twl4030-vpll2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vsim: regulator-vsim { compatible = "ti,twl4030-vsim"; regulator-min-microvolt = <1800000>; @@ -98,4 +134,9 @@ compatible = "ti,twl4030-pwmled"; #pwm-cells = <2>; }; + + twl_pwrbutton: pwrbutton { + compatible = "ti,twl4030-pwrbutton"; + interrupts = <8>; + }; }; diff --git a/arch/arm/boot/dts/twl6030_omap4.dtsi b/arch/arm/boot/dts/twl6030_omap4.dtsi new file mode 100644 index 0000000..a4fa570 --- /dev/null +++ b/arch/arm/boot/dts/twl6030_omap4.dtsi @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +&twl { + /* + * On most OMAP4 platforms, the twl6030 IRQ line is connected + * to the SYS_NIRQ1 line on OMAP and the twl6030 MSECURE line is + * connected to the fref_clk0_out.sys_drm_msecure line. + * Therefore, configure the defaults for the SYS_NIRQ1 and + * fref_clk0_out.sys_drm_msecure pins here. + */ + pinctrl-names = "default"; + pinctrl-0 = < + &twl6030_pins + &twl6030_wkup_pins + >; +}; + +&omap4_pmx_wkup { + twl6030_wkup_pins: pinmux_twl6030_wkup_pins { + pinctrl-single,pins = < + 0x14 (PIN_OUTPUT | MUX_MODE2) /* fref_clk0_out.sys_drm_msecure */ + >; + }; +}; + +&omap4_pmx_core { + twl6030_pins: pinmux_twl6030_pins { + pinctrl-single,pins = < + 0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1.sys_nirq1 */ + >; + }; +}; diff --git a/arch/arm/boot/dts/vf610-cosmic.dts b/arch/arm/boot/dts/vf610-cosmic.dts new file mode 100644 index 0000000..c42e4f9 --- /dev/null +++ b/arch/arm/boot/dts/vf610-cosmic.dts @@ -0,0 +1,47 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * Copyright 2013 Linaro Limited + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +/dts-v1/; +#include "vf610.dtsi" + +/ { + model = "PHYTEC Cosmic/Cosmic+ Board"; + compatible = "phytec,vf610-cosmic", "fsl,vf610"; + + chosen { + bootargs = "console=ttyLP1,115200"; + }; + + memory { + reg = <0x80000000 0x10000000>; + }; + + clocks { + enet_ext { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + }; + +}; + +&fec1 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1_1>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_1>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts index 1a58678..c8047ca 100644 --- a/arch/arm/boot/dts/vf610-twr.dts +++ b/arch/arm/boot/dts/vf610-twr.dts @@ -36,6 +36,23 @@ }; +&dspi0 { + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0_1>; + status = "okay"; + + sflash: at26df081a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at26df081a"; + spi-max-frequency = <16000000>; + spi-cpol; + spi-cpha; + reg = <0>; + }; +}; + &fec0 { phy-mode = "rmii"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi index 67d929c..d31ce1b 100644 --- a/arch/arm/boot/dts/vf610.dtsi +++ b/arch/arm/boot/dts/vf610.dtsi @@ -123,6 +123,18 @@ status = "disabled"; }; + dspi0: dspi0@4002c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x4002c000 0x1000>; + interrupts = <0 67 0x04>; + clocks = <&clks VF610_CLK_DSPI0>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + status = "disabled"; + }; + sai2: sai@40031000 { compatible = "fsl,vf610-sai"; reg = <0x40031000 0x1000>; diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 254cf05..98a50c3 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -1,14 +1,13 @@ -CONFIG_EXPERIMENTAL=y CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=16 CONFIG_BLK_DEV_INITRD=y CONFIG_EXPERT=y -# CONFIG_SYSCTL_SYSCALL is not set -CONFIG_KALLSYMS_EXTRA_PASS=y CONFIG_SLAB=y CONFIG_PROFILING=y CONFIG_OPROFILE=y @@ -20,22 +19,21 @@ CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y # CONFIG_BLK_DEV_BSG is not set +CONFIG_PARTITION_ADVANCED=y CONFIG_ARCH_MULTI_V6=y -CONFIG_ARCH_OMAP2PLUS=y +CONFIG_OMAP_RESET_CLOCKS=y +CONFIG_OMAP_MUX_DEBUG=y CONFIG_ARCH_OMAP2=y CONFIG_ARCH_OMAP3=y CONFIG_ARCH_OMAP4=y +CONFIG_SOC_OMAP5=y CONFIG_SOC_AM33XX=y -CONFIG_OMAP_RESET_CLOCKS=y -CONFIG_OMAP_MUX_DEBUG=y -CONFIG_ARCH_VEXPRESS_CA9X4=y +CONFIG_SOC_DRA7XX=y CONFIG_ARM_THUMBEE=y CONFIG_ARM_ERRATA_411920=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y CONFIG_SMP=y CONFIG_NR_CPUS=2 -CONFIG_LEDS=y +CONFIG_CMA=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 CONFIG_ARM_APPENDED_DTB=y @@ -61,8 +59,6 @@ CONFIG_IP_PNP_RARP=y # CONFIG_IPV6 is not set CONFIG_NETFILTER=y CONFIG_CAN=m -CONFIG_CAN_RAW=m -CONFIG_CAN_BCM=m CONFIG_CAN_C_CAN=m CONFIG_CAN_C_CAN_PLATFORM=m CONFIG_BT=m @@ -77,14 +73,13 @@ CONFIG_MAC80211=m CONFIG_MAC80211_RC_PID=y CONFIG_MAC80211_RC_DEFAULT_PID=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_CMA=y -CONFIG_DMA_CMA=y -CONFIG_CONNECTOR=y CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y +CONFIG_DMA_CMA=y +CONFIG_OMAP_OCP2SCP=y +CONFIG_CONNECTOR=y CONFIG_MTD=y CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_CHAR=y CONFIG_MTD_BLOCK=y CONFIG_MTD_OOPS=y CONFIG_MTD_CFI=y @@ -98,32 +93,40 @@ CONFIG_MTD_UBI=y CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_SIZE=16384 -CONFIG_SENSORS_LIS3LV02D=m CONFIG_SENSORS_TSL2550=m -CONFIG_SENSORS_LIS3_I2C=m CONFIG_BMP085_I2C=m +CONFIG_SENSORS_LIS3_I2C=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_SCAN_ASYNC=y CONFIG_MD=y CONFIG_NETDEVICES=y -CONFIG_SMSC_PHY=y -CONFIG_NET_ETHERNET=y -CONFIG_SMC91X=y -CONFIG_SMSC911X=y CONFIG_KS8851=y CONFIG_KS8851_MLL=y -CONFIG_LIBERTAS=m -CONFIG_LIBERTAS_USB=m -CONFIG_LIBERTAS_SDIO=m -CONFIG_LIBERTAS_DEBUG=y +CONFIG_SMC91X=y +CONFIG_SMSC911X=y +CONFIG_TI_CPSW=y +CONFIG_AT803X_PHY=y +CONFIG_SMSC_PHY=y CONFIG_USB_USBNET=y CONFIG_USB_NET_SMSC95XX=y CONFIG_USB_ALI_M5632=y CONFIG_USB_AN2720=y CONFIG_USB_EPSON2888=y CONFIG_USB_KC2190=y +CONFIG_LIBERTAS=m +CONFIG_LIBERTAS_USB=m +CONFIG_LIBERTAS_SDIO=m +CONFIG_LIBERTAS_DEBUG=y +CONFIG_WL_TI=y +CONFIG_WL12XX=m +CONFIG_WL18XX=m +CONFIG_WLCORE_SPI=m +CONFIG_WLCORE_SDIO=m +CONFIG_MWIFIEX=m +CONFIG_MWIFIEX_SDIO=m +CONFIG_MWIFIEX_USB=m CONFIG_INPUT_JOYDEV=y CONFIG_INPUT_EVDEV=y CONFIG_KEYBOARD_GPIO=y @@ -133,7 +136,6 @@ CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_ADS7846=y CONFIG_INPUT_MISC=y CONFIG_INPUT_TWL4030_PWRBUTTON=y -CONFIG_VT_HW_CONSOLE_BINDING=y # CONFIG_LEGACY_PTYS is not set CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y @@ -143,8 +145,7 @@ CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y CONFIG_SERIAL_8250_DETECT_IRQ=y CONFIG_SERIAL_8250_RSA=y -CONFIG_SERIAL_AMBA_PL011=y -CONFIG_SERIAL_AMBA_PL011_CONSOLE=y +CONFIG_SERIAL_OF_PLATFORM=y CONFIG_SERIAL_OMAP=y CONFIG_SERIAL_OMAP_CONSOLE=y CONFIG_HW_RANDOM=y @@ -158,31 +159,31 @@ CONFIG_GPIO_TWL4030=y CONFIG_W1=y CONFIG_POWER_SUPPLY=y CONFIG_SENSORS_LM75=m -CONFIG_WATCHDOG=y CONFIG_THERMAL=y -CONFIG_THERMAL_HWMON=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y CONFIG_THERMAL_GOV_FAIR_SHARE=y -CONFIG_THERMAL_GOV_STEP_WISE=y CONFIG_THERMAL_GOV_USER_SPACE=y -CONFIG_CPU_THERMAL=y +CONFIG_TI_SOC_THERMAL=y +CONFIG_OMAP4_THERMAL=y +CONFIG_OMAP5_THERMAL=y +CONFIG_DRA752_THERMAL=y +CONFIG_WATCHDOG=y CONFIG_OMAP_WATCHDOG=y CONFIG_TWL4030_WATCHDOG=y +CONFIG_MFD_PALMAS=y CONFIG_MFD_TPS65217=y CONFIG_MFD_TPS65910=y CONFIG_TWL6040_CORE=y -CONFIG_REGULATOR_TWL4030=y +CONFIG_REGULATOR_PALMAS=y CONFIG_REGULATOR_TPS65023=y CONFIG_REGULATOR_TPS6507X=y CONFIG_REGULATOR_TPS65217=y CONFIG_REGULATOR_TPS65910=y +CONFIG_REGULATOR_TWL4030=y CONFIG_FB=y CONFIG_FIRMWARE_EDID=y CONFIG_FB_MODE_HELPERS=y CONFIG_FB_TILEBLITTING=y -CONFIG_FB_OMAP_LCD_VGA=y CONFIG_OMAP2_DSS=m -CONFIG_OMAP2_DSS_RFBI=y CONFIG_OMAP2_DSS_SDI=y CONFIG_OMAP2_DSS_DSI=y CONFIG_FB_OMAP2=m @@ -194,12 +195,8 @@ CONFIG_DISPLAY_PANEL_DPI=m CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_LCD_CLASS_DEVICE=y CONFIG_LCD_PLATFORM=y -CONFIG_DISPLAY_SUPPORT=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y -CONFIG_FONTS=y -CONFIG_FONT_8x8=y -CONFIG_FONT_8x16=y CONFIG_LOGO=y CONFIG_SOUND=m CONFIG_SND=m @@ -216,14 +213,14 @@ CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m CONFIG_USB=y CONFIG_USB_DEBUG=y CONFIG_USB_ANNOUNCE_NEW_DEVICES=y -CONFIG_USB_DEVICEFS=y CONFIG_USB_MON=y CONFIG_USB_WDM=y CONFIG_USB_STORAGE=y -CONFIG_USB_LIBUSUAL=y +CONFIG_USB_DWC3=m CONFIG_USB_TEST=y -CONFIG_USB_PHY=y CONFIG_NOP_USB_XCEIV=y +CONFIG_OMAP_USB2=y +CONFIG_OMAP_USB3=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DEBUG=y CONFIG_USB_GADGET_DEBUG_FILES=y @@ -232,7 +229,6 @@ CONFIG_USB_ZERO=m CONFIG_MMC=y CONFIG_MMC_UNSAFE_RESUME=y CONFIG_SDIO_UART=y -CONFIG_MMC_ARMMMCI=y CONFIG_MMC_OMAP=y CONFIG_MMC_OMAP_HS=y CONFIG_NEW_LEDS=y @@ -252,11 +248,8 @@ CONFIG_RTC_DRV_OMAP=y CONFIG_DMADEVICES=y CONFIG_TI_EDMA=y CONFIG_DMA_OMAP=y -CONFIG_TI_SOC_THERMAL=y -CONFIG_TI_THERMAL=y -CONFIG_OMAP4_THERMAL=y -CONFIG_OMAP5_THERMAL=y -CONFIG_DRA752_THERMAL=y +CONFIG_EXTCON=y +CONFIG_EXTCON_PALMAS=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set @@ -275,23 +268,18 @@ CONFIG_JFFS2_RUBIN=y CONFIG_UBIFS_FS=y CONFIG_CRAMFS=y CONFIG_NFS_FS=y -CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y CONFIG_ROOT_NFS=y -CONFIG_PARTITION_ADVANCED=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_PRINTK_TIME=y +CONFIG_DEBUG_INFO=y CONFIG_MAGIC_SYSRQ=y -CONFIG_DEBUG_KERNEL=y CONFIG_SCHEDSTATS=y CONFIG_TIMER_STATS=y CONFIG_PROVE_LOCKING=y -CONFIG_DEBUG_SPINLOCK_SLEEP=y # CONFIG_DEBUG_BUGVERBOSE is not set -CONFIG_DEBUG_INFO=y -# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SECURITY=y CONFIG_CRYPTO_MICHAEL_MIC=y # CONFIG_CRYPTO_ANSI_CPRNG is not set @@ -300,9 +288,6 @@ CONFIG_CRC_T10DIF=y CONFIG_CRC_ITU_T=y CONFIG_CRC7=y CONFIG_LIBCRC32C=y -CONFIG_SOC_OMAP5=y -CONFIG_TI_DAVINCI_MDIO=y -CONFIG_TI_DAVINCI_CPDMA=y -CONFIG_TI_CPSW=y -CONFIG_AT803X_PHY=y -CONFIG_SOC_DRA7XX=y +CONFIG_FONTS=y +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig index a0025dc..ac632cc 100644 --- a/arch/arm/configs/u8500_defconfig +++ b/arch/arm/configs/u8500_defconfig @@ -1,4 +1,3 @@ -CONFIG_HIGHMEM=y # CONFIG_SWAP is not set CONFIG_SYSVIPC=y CONFIG_NO_HZ=y @@ -16,6 +15,9 @@ CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PREEMPT=y CONFIG_AEABI=y +CONFIG_HIGHMEM=y +CONFIG_ARM_APPENDED_DTB=y +CONFIG_ARM_ATAG_DTB_COMPAT=y CONFIG_CMDLINE="root=/dev/ram0 console=ttyAMA2,115200n8" CONFIG_CPU_FREQ=y CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y @@ -68,8 +70,8 @@ CONFIG_CPU_THERMAL=y CONFIG_WATCHDOG=y CONFIG_MFD_STMPE=y CONFIG_MFD_TC3589X=y -CONFIG_REGULATOR_GPIO=y CONFIG_REGULATOR_AB8500=y +CONFIG_REGULATOR_GPIO=y CONFIG_SOUND=y CONFIG_SND=y CONFIG_SND_SOC=y @@ -78,10 +80,8 @@ CONFIG_SND_SOC_UX500_MACH_MOP500=y CONFIG_USB=y CONFIG_USB_MUSB_HDRC=y CONFIG_USB_MUSB_UX500=y -CONFIG_USB_PHY=y CONFIG_AB8500_USB=y CONFIG_USB_GADGET=y -CONFIG_USB_GADGET_MUSB_HDRC=y CONFIG_USB_ETH=m CONFIG_MMC=y CONFIG_MMC_UNSAFE_RESUME=y @@ -116,12 +116,12 @@ CONFIG_NFS_FS=y CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y -CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_INFO=y CONFIG_DEBUG_FS=y +CONFIG_MAGIC_SYSRQ=y CONFIG_DEBUG_KERNEL=y # CONFIG_SCHED_DEBUG is not set # CONFIG_DEBUG_PREEMPT is not set -CONFIG_DEBUG_INFO=y # CONFIG_FTRACE is not set CONFIG_DEBUG_USER=y CONFIG_CRYPTO_DEV_UX500=y diff --git a/arch/arm/mach-at91/at91sam9n12.c b/arch/arm/mach-at91/at91sam9n12.c index c7d670d..2d895a2 100644 --- a/arch/arm/mach-at91/at91sam9n12.c +++ b/arch/arm/mach-at91/at91sam9n12.c @@ -169,6 +169,7 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb_clk), CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb_clk), CLKDEV_CON_DEV_ID("mci_clk", "f0008000.mmc", &mmc_clk), + CLKDEV_CON_DEV_ID(NULL, "f0010000.ssc", &ssc_clk), CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk), CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk), CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk), diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c index c9f6fd2..9caa4fe 100644 --- a/arch/arm/mach-kirkwood/board-dt.c +++ b/arch/arm/mach-kirkwood/board-dt.c @@ -151,7 +151,6 @@ static void __init kirkwood_dt_init(void) writel(readl(CPU_CONFIG) & ~CPU_CONFIG_ERROR_PROP, CPU_CONFIG); BUG_ON(mvebu_mbus_dt_init()); - kirkwood_setup_wins(); kirkwood_l2_init(); diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c index cc511a4..1dc5acd 100644 --- a/arch/arm/mach-mxs/mach-mxs.c +++ b/arch/arm/mach-mxs/mach-mxs.c @@ -330,6 +330,11 @@ static void __init crystalfontz_init(void) update_fec_mac_prop(OUI_CRYSTALFONTZ); } +static void __init m28cu3_init(void) +{ + update_fec_mac_prop(OUI_DENX); +} + static const char __init *mxs_get_soc_id(void) { struct device_node *np; @@ -457,6 +462,8 @@ static void __init mxs_machine_init(void) apx4devkit_init(); else if (of_machine_is_compatible("crystalfontz,cfa10036")) crystalfontz_init(); + else if (of_machine_is_compatible("msr,m28cu3")) + m28cu3_init(); of_platform_populate(NULL, of_default_bus_match_table, NULL, parent); diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index c946244..dc21df1 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -87,6 +87,7 @@ config ARCH_OMAP2PLUS select COMMON_CLK select GENERIC_CLOCKEVENTS select GENERIC_IRQ_CHIP + select MACH_OMAP_GENERIC select OMAP_DM_TIMER select PINCTRL select PROC_DEVICETREE if PROC_FS @@ -180,16 +181,11 @@ config OMAP_PACKAGE_CUS config OMAP_PACKAGE_CBP bool -comment "OMAP Board Type" +comment "OMAP Legacy Platform Data Board Type" depends on ARCH_OMAP2PLUS config MACH_OMAP_GENERIC - bool "Generic OMAP2+ board" - depends on ARCH_OMAP2PLUS - default y - help - Support for generic TI OMAP2+ boards using Flattened Device Tree. - More information at Documentation/devicetree + bool config MACH_OMAP2_TUSB6010 bool @@ -253,12 +249,6 @@ config MACH_OVERO default y select OMAP_PACKAGE_CBB -config MACH_OMAP3EVM - bool "OMAP 3530 EVM board" - depends on ARCH_OMAP3 - default y - select OMAP_PACKAGE_CBB - config MACH_OMAP3517EVM bool "OMAP3517/ AM3517 EVM board" depends on ARCH_OMAP3 @@ -307,33 +297,12 @@ config MACH_NOKIA_N8X0 select MACH_NOKIA_N810_WIMAX select OMAP_PACKAGE_ZAC -config MACH_NOKIA_RM680 - bool "Nokia N950 (RM-680) / N9 (RM-696) phones" - depends on ARCH_OMAP3 - default y - select MACH_NOKIA_RM696 - select OMAP_PACKAGE_CBB - config MACH_NOKIA_RX51 bool "Nokia N900 (RX-51) phone" depends on ARCH_OMAP3 default y select OMAP_PACKAGE_CBB -config MACH_OMAP_ZOOM2 - bool "OMAP3 Zoom2 board" - depends on ARCH_OMAP3 - default y - select OMAP_PACKAGE_CBB - select REGULATOR_FIXED_VOLTAGE if REGULATOR - -config MACH_OMAP_ZOOM3 - bool "OMAP3630 Zoom3 board" - depends on ARCH_OMAP3 - default y - select OMAP_PACKAGE_CBP - select REGULATOR_FIXED_VOLTAGE if REGULATOR - config MACH_CM_T35 bool "CompuLab CM-T35/CM-T3730 modules" depends on ARCH_OMAP3 @@ -350,31 +319,12 @@ config MACH_CM_T3517 config MACH_CM_T3730 bool -config MACH_IGEP0020 - bool "IGEP v2 board" - depends on ARCH_OMAP3 - default y - select OMAP_PACKAGE_CBB - -config MACH_IGEP0030 - bool "IGEP OMAP3 module" - depends on ARCH_OMAP3 - default y - select MACH_IGEP0020 - select OMAP_PACKAGE_CBB - config MACH_SBC3530 bool "OMAP3 SBC STALKER board" depends on ARCH_OMAP3 default y select OMAP_PACKAGE_CUS -config MACH_OMAP_3630SDP - bool "OMAP3630 SDP board" - depends on ARCH_OMAP3 - default y - select OMAP_PACKAGE_CBP - config MACH_TI8168EVM bool "TI8168 Evaluation Module" depends on SOC_TI81XX diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 9b7619f..e15ac00 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -236,7 +236,7 @@ endif obj-$(CONFIG_SOC_OMAP2420) += msdi.o # Specific board support -obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o +obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o obj-$(CONFIG_MACH_OMAP_H4) += board-h4.o obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o @@ -245,26 +245,14 @@ obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o obj-$(CONFIG_MACH_OVERO) += board-overo.o -obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o obj-$(CONFIG_MACH_OMAP_3430SDP) += board-3430sdp.o obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o -obj-$(CONFIG_MACH_NOKIA_RM680) += board-rm680.o sdram-nokia.o obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o sdram-nokia.o obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o -obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom.o board-zoom-peripherals.o -obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom-display.o -obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom-debugboard.o -obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom.o board-zoom-peripherals.o -obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom-display.o -obj-$(CONFIG_MACH_OMAP_ZOOM3) += board-zoom-debugboard.o -obj-$(CONFIG_MACH_OMAP_3630SDP) += board-3630sdp.o -obj-$(CONFIG_MACH_OMAP_3630SDP) += board-zoom-peripherals.o -obj-$(CONFIG_MACH_OMAP_3630SDP) += board-zoom-display.o obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o obj-$(CONFIG_MACH_CM_T3517) += board-cm-t3517.o -obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o obj-$(CONFIG_MACH_OMAP3517EVM) += board-am3517evm.o diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c deleted file mode 100644 index 20d6d81..0000000 --- a/arch/arm/mach-omap2/board-3630sdp.c +++ /dev/null @@ -1,225 +0,0 @@ -/* - * Copyright (C) 2009 Texas Instruments Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/input.h> -#include <linux/gpio.h> -#include <linux/mtd/nand.h> - -#include <asm/mach-types.h> -#include <asm/mach/arch.h> - -#include "common.h" -#include "gpmc-smc91x.h" - -#include "board-zoom.h" - -#include "board-flash.h" -#include "mux.h" -#include "sdram-hynix-h8mbx00u0mer-0em.h" - -#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) - -static struct omap_smc91x_platform_data board_smc91x_data = { - .cs = 3, - .flags = GPMC_MUX_ADD_DATA | IORESOURCE_IRQ_LOWLEVEL, -}; - -static void __init board_smc91x_init(void) -{ - board_smc91x_data.gpio_irq = 158; - gpmc_smc91x_init(&board_smc91x_data); -} - -#else - -static inline void board_smc91x_init(void) -{ -} - -#endif /* defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) */ - -static void enable_board_wakeup_source(void) -{ - /* T2 interrupt line (keypad) */ - omap_mux_init_signal("sys_nirq", - OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP); -} - -static struct usbhs_phy_data phy_data[] __initdata = { - { - .port = 1, - .reset_gpio = 126, - .vcc_gpio = -EINVAL, - }, - { - .port = 2, - .reset_gpio = 61, - .vcc_gpio = -EINVAL, - }, -}; - -static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, -}; - -#ifdef CONFIG_OMAP_MUX -static struct omap_board_mux board_mux[] __initdata = { - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; -#endif - -/* - * SDP3630 CS organization - * See also the Switch S8 settings in the comments. - */ -static char chip_sel_sdp[][GPMC_CS_NUM] = { - {PDC_NOR, PDC_NAND, PDC_ONENAND, DBG_MPDB, 0, 0, 0, 0}, /* S8:1111 */ - {PDC_ONENAND, PDC_NAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1110 */ - {PDC_NAND, PDC_ONENAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1101 */ -}; - -static struct mtd_partition sdp_nor_partitions[] = { - /* bootloader (U-Boot, etc) in first sector */ - { - .name = "Bootloader-NOR", - .offset = 0, - .size = SZ_256K, - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - /* bootloader params in the next sector */ - { - .name = "Params-NOR", - .offset = MTDPART_OFS_APPEND, - .size = SZ_256K, - .mask_flags = 0, - }, - /* kernel */ - { - .name = "Kernel-NOR", - .offset = MTDPART_OFS_APPEND, - .size = SZ_2M, - .mask_flags = 0 - }, - /* file system */ - { - .name = "Filesystem-NOR", - .offset = MTDPART_OFS_APPEND, - .size = MTDPART_SIZ_FULL, - .mask_flags = 0 - } -}; - -static struct mtd_partition sdp_onenand_partitions[] = { - { - .name = "X-Loader-OneNAND", - .offset = 0, - .size = 4 * (64 * 2048), - .mask_flags = MTD_WRITEABLE /* force read-only */ - }, - { - .name = "U-Boot-OneNAND", - .offset = MTDPART_OFS_APPEND, - .size = 2 * (64 * 2048), - .mask_flags = MTD_WRITEABLE /* force read-only */ - }, - { - .name = "U-Boot Environment-OneNAND", - .offset = MTDPART_OFS_APPEND, - .size = 1 * (64 * 2048), - }, - { - .name = "Kernel-OneNAND", - .offset = MTDPART_OFS_APPEND, - .size = 16 * (64 * 2048), - }, - { - .name = "File System-OneNAND", - .offset = MTDPART_OFS_APPEND, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition sdp_nand_partitions[] = { - /* All the partition sizes are listed in terms of NAND block size */ - { - .name = "X-Loader-NAND", - .offset = 0, - .size = 4 * (64 * 2048), - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - { - .name = "U-Boot-NAND", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */ - .size = 10 * (64 * 2048), - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - { - .name = "Boot Env-NAND", - - .offset = MTDPART_OFS_APPEND, /* Offset = 0x1c0000 */ - .size = 6 * (64 * 2048), - }, - { - .name = "Kernel-NAND", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */ - .size = 40 * (64 * 2048), - }, - { - .name = "File System - NAND", - .size = MTDPART_SIZ_FULL, - .offset = MTDPART_OFS_APPEND, /* Offset = 0x780000 */ - }, -}; - -static struct flash_partitions sdp_flash_partitions[] = { - { - .parts = sdp_nor_partitions, - .nr_parts = ARRAY_SIZE(sdp_nor_partitions), - }, - { - .parts = sdp_onenand_partitions, - .nr_parts = ARRAY_SIZE(sdp_onenand_partitions), - }, - { - .parts = sdp_nand_partitions, - .nr_parts = ARRAY_SIZE(sdp_nand_partitions), - }, -}; - -static void __init omap_sdp_init(void) -{ - omap3_mux_init(board_mux, OMAP_PACKAGE_CBP); - zoom_peripherals_init(); - omap_sdrc_init(h8mbx00u0mer0em_sdrc_params, - h8mbx00u0mer0em_sdrc_params); - zoom_display_init(); - board_smc91x_init(); - board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16); - enable_board_wakeup_source(); - - usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); - usbhs_init(&usbhs_bdata); -} - -MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board") - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap3630_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = omap_sdp_init, - .init_late = omap3630_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 87162e1..19f1652 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -15,13 +15,10 @@ #include <linux/of_irq.h> #include <linux/of_platform.h> #include <linux/irqdomain.h> -#include <linux/clk.h> #include <asm/mach/arch.h> #include "common.h" -#include "common-board-devices.h" -#include "dss-common.h" #if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)) #define intc_of_init NULL @@ -36,40 +33,9 @@ static struct of_device_id omap_dt_match_table[] __initdata = { { } }; -/* - * Create alias for USB host PHY clock. - * Remove this when clock phandle can be provided via DT - */ -static void __init legacy_init_ehci_clk(char *clkname) -{ - int ret; - - ret = clk_add_alias("main_clk", NULL, clkname, NULL); - if (ret) { - pr_err("%s:Failed to add main_clk alias to %s :%d\n", - __func__, clkname, ret); - } -} - static void __init omap_generic_init(void) { - omap_sdrc_init(NULL, NULL); - - of_platform_populate(NULL, omap_dt_match_table, NULL, NULL); - - /* - * HACK: call display setup code for selected boards to enable omapdss. - * This will be removed when omapdss supports DT. - */ - if (of_machine_is_compatible("ti,omap4-panda")) { - omap4_panda_display_init_of(); - legacy_init_ehci_clk("auxclk3_ck"); - - } - else if (of_machine_is_compatible("ti,omap4-sdp")) - omap_4430sdp_display_init_of(); - else if (of_machine_is_compatible("ti,omap5-uevm")) - legacy_init_ehci_clk("auxclk1_ck"); + pdata_quirks_init(omap_dt_match_table); } #ifdef CONFIG_SOC_OMAP2420 @@ -180,6 +146,7 @@ DT_MACHINE_START(AM33XX_DT, "Generic AM33XX (Flattened Device Tree)") .init_irq = omap_intc_of_init, .handle_irq = omap3_intc_handle_irq, .init_machine = omap_generic_init, + .init_late = am33xx_init_late, .init_time = omap3_gptimer_timer_init, .dt_compat = am33xx_boards_compat, .restart = am33xx_restart, @@ -219,6 +186,7 @@ DT_MACHINE_START(OMAP5_DT, "Generic OMAP5 (Flattened Device Tree)") .init_early = omap5_init_early, .init_irq = omap_gic_of_init, .init_machine = omap_generic_init, + .init_late = omap5_init_late, .init_time = omap5_realtime_timer_init, .dt_compat = omap5_boards_compat, .restart = omap44xx_restart, @@ -234,6 +202,7 @@ static const char *am43_boards_compat[] __initdata = { DT_MACHINE_START(AM43_DT, "Generic AM43 (Flattened Device Tree)") .map_io = am33xx_map_io, .init_early = am43xx_init_early, + .init_late = am43xx_init_late, .init_irq = omap_gic_of_init, .init_machine = omap_generic_init, .init_time = omap3_sync32k_timer_init, @@ -252,6 +221,7 @@ DT_MACHINE_START(DRA7XX_DT, "Generic DRA7XX (Flattened Device Tree)") .smp = smp_ops(omap4_smp_ops), .map_io = omap5_map_io, .init_early = dra7xx_init_early, + .init_late = dra7xx_init_late, .init_irq = omap_gic_of_init, .init_machine = omap_generic_init, .init_time = omap5_realtime_timer_init, diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c deleted file mode 100644 index 06dbb2d..0000000 --- a/arch/arm/mach-omap2/board-igep0020.c +++ /dev/null @@ -1,718 +0,0 @@ -/* - * Copyright (C) 2009 Integration Software and Electronic Engineering. - * - * Modified from mach-omap2/board-generic.c - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/delay.h> -#include <linux/err.h> -#include <linux/clk.h> -#include <linux/io.h> -#include <linux/gpio.h> -#include <linux/interrupt.h> -#include <linux/input.h> -#include <linux/usb/phy.h> - -#include <linux/regulator/machine.h> -#include <linux/regulator/fixed.h> -#include <linux/i2c/twl.h> -#include <linux/mmc/host.h> - -#include <linux/mtd/nand.h> - -#include <asm/mach-types.h> -#include <asm/mach/arch.h> - -#include <video/omapdss.h> -#include <video/omap-panel-data.h> -#include <linux/platform_data/mtd-onenand-omap2.h> - -#include "common.h" -#include "gpmc.h" -#include "mux.h" -#include "hsmmc.h" -#include "sdram-numonyx-m65kxxxxam.h" -#include "common-board-devices.h" -#include "board-flash.h" -#include "control.h" -#include "gpmc-onenand.h" - -#define IGEP2_SMSC911X_CS 5 -#define IGEP2_SMSC911X_GPIO 176 -#define IGEP2_GPIO_USBH_NRESET 24 -#define IGEP2_GPIO_LED0_GREEN 26 -#define IGEP2_GPIO_LED0_RED 27 -#define IGEP2_GPIO_LED1_RED 28 -#define IGEP2_GPIO_DVI_PUP 170 - -#define IGEP2_RB_GPIO_WIFI_NPD 94 -#define IGEP2_RB_GPIO_WIFI_NRESET 95 -#define IGEP2_RB_GPIO_BT_NRESET 137 -#define IGEP2_RC_GPIO_WIFI_NPD 138 -#define IGEP2_RC_GPIO_WIFI_NRESET 139 -#define IGEP2_RC_GPIO_BT_NRESET 137 - -#define IGEP3_GPIO_LED0_GREEN 54 -#define IGEP3_GPIO_LED0_RED 53 -#define IGEP3_GPIO_LED1_RED 16 -#define IGEP3_GPIO_USBH_NRESET 183 - -#define IGEP_SYSBOOT_MASK 0x1f -#define IGEP_SYSBOOT_NAND 0x0f -#define IGEP_SYSBOOT_ONENAND 0x10 - -/* - * IGEP2 Hardware Revision Table - * - * -------------------------------------------------------------------------- - * | Id. | Hw Rev. | HW0 (28) | WIFI_NPD | WIFI_NRESET | BT_NRESET | - * -------------------------------------------------------------------------- - * | 0 | B | high | gpio94 | gpio95 | - | - * | 0 | B/C (B-compatible) | high | gpio94 | gpio95 | gpio137 | - * | 1 | C | low | gpio138 | gpio139 | gpio137 | - * -------------------------------------------------------------------------- - */ - -#define IGEP2_BOARD_HWREV_B 0 -#define IGEP2_BOARD_HWREV_C 1 -#define IGEP3_BOARD_HWREV 2 - -static u8 hwrev; - -static void __init igep2_get_revision(void) -{ - u8 ret; - - if (machine_is_igep0030()) { - hwrev = IGEP3_BOARD_HWREV; - return; - } - - omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT); - - if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) { - pr_warning("IGEP2: Could not obtain gpio GPIO_HW0_REV\n"); - pr_err("IGEP2: Unknown Hardware Revision\n"); - return; - } - - ret = gpio_get_value(IGEP2_GPIO_LED1_RED); - if (ret == 0) { - pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n"); - hwrev = IGEP2_BOARD_HWREV_C; - } else if (ret == 1) { - pr_info("IGEP2: Hardware Revision B/C (B compatible)\n"); - hwrev = IGEP2_BOARD_HWREV_B; - } else { - pr_err("IGEP2: Unknown Hardware Revision\n"); - hwrev = -1; - } - - gpio_free(IGEP2_GPIO_LED1_RED); -} - -#if defined(CONFIG_MTD_ONENAND_OMAP2) || \ - defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) || \ - defined(CONFIG_MTD_NAND_OMAP2) || \ - defined(CONFIG_MTD_NAND_OMAP2_MODULE) - -#define ONENAND_MAP 0x20000000 - -/* NAND04GR4E1A ( x2 Flash built-in COMBO POP MEMORY ) - * Since the device is equipped with two DataRAMs, and two-plane NAND - * Flash memory array, these two component enables simultaneous program - * of 4KiB. Plane1 has only even blocks such as block0, block2, block4 - * while Plane2 has only odd blocks such as block1, block3, block5. - * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048) - */ - -static struct mtd_partition igep_flash_partitions[] = { - { - .name = "X-Loader", - .offset = 0, - .size = 2 * (64*(2*2048)) - }, - { - .name = "U-Boot", - .offset = MTDPART_OFS_APPEND, - .size = 6 * (64*(2*2048)), - }, - { - .name = "Environment", - .offset = MTDPART_OFS_APPEND, - .size = 2 * (64*(2*2048)), - }, - { - .name = "Kernel", - .offset = MTDPART_OFS_APPEND, - .size = 12 * (64*(2*2048)), - }, - { - .name = "File System", - .offset = MTDPART_OFS_APPEND, - .size = MTDPART_SIZ_FULL, - }, -}; - -static inline u32 igep_get_sysboot_value(void) -{ - return omap_ctrl_readl(OMAP343X_CONTROL_STATUS) & IGEP_SYSBOOT_MASK; -} - -static void __init igep_flash_init(void) -{ - u32 mux; - mux = igep_get_sysboot_value(); - - if (mux == IGEP_SYSBOOT_NAND) { - pr_info("IGEP: initializing NAND memory device\n"); - board_nand_init(igep_flash_partitions, - ARRAY_SIZE(igep_flash_partitions), - 0, NAND_BUSWIDTH_16, nand_default_timings); - } else if (mux == IGEP_SYSBOOT_ONENAND) { - pr_info("IGEP: initializing OneNAND memory device\n"); - board_onenand_init(igep_flash_partitions, - ARRAY_SIZE(igep_flash_partitions), 0); - } else { - pr_err("IGEP: Flash: unsupported sysboot sequence found\n"); - } -} - -#else -static void __init igep_flash_init(void) {} -#endif - -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) - -#include <linux/smsc911x.h> -#include "gpmc-smsc911x.h" - -static struct omap_smsc911x_platform_data smsc911x_cfg = { - .cs = IGEP2_SMSC911X_CS, - .gpio_irq = IGEP2_SMSC911X_GPIO, - .gpio_reset = -EINVAL, - .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, -}; - -static inline void __init igep2_init_smsc911x(void) -{ - gpmc_smsc911x_init(&smsc911x_cfg); -} - -#else -static inline void __init igep2_init_smsc911x(void) { } -#endif - -static struct regulator_consumer_supply igep_vmmc1_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"), -}; - -/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ -static struct regulator_init_data igep_vmmc1 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 3150000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(igep_vmmc1_supply), - .consumer_supplies = igep_vmmc1_supply, -}; - -static struct regulator_consumer_supply igep_vio_supply[] = { - REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1"), -}; - -static struct regulator_init_data igep_vio = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = 1, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(igep_vio_supply), - .consumer_supplies = igep_vio_supply, -}; - -static struct regulator_consumer_supply igep_vmmc2_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"), -}; - -static struct regulator_init_data igep_vmmc2 = { - .constraints = { - .valid_modes_mask = REGULATOR_MODE_NORMAL, - .always_on = 1, - }, - .num_consumer_supplies = ARRAY_SIZE(igep_vmmc2_supply), - .consumer_supplies = igep_vmmc2_supply, -}; - -static struct fixed_voltage_config igep_vwlan = { - .supply_name = "vwlan", - .microvolts = 3300000, - .gpio = -EINVAL, - .enabled_at_boot = 1, - .init_data = &igep_vmmc2, -}; - -static struct platform_device igep_vwlan_device = { - .name = "reg-fixed-voltage", - .id = 0, - .dev = { - .platform_data = &igep_vwlan, - }, -}; - -static struct omap2_hsmmc_info mmc[] = { - { - .mmc = 1, - .caps = MMC_CAP_4_BIT_DATA, - .gpio_cd = -EINVAL, - .gpio_wp = -EINVAL, - .deferred = true, - }, -#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE) - { - .mmc = 2, - .caps = MMC_CAP_4_BIT_DATA, - .gpio_cd = -EINVAL, - .gpio_wp = -EINVAL, - }, -#endif - {} /* Terminator */ -}; - -#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE) -#include <linux/leds.h> - -static struct gpio_led igep_gpio_leds[] = { - [0] = { - .name = "omap3:red:user0", - .default_state = 0, - }, - [1] = { - .name = "omap3:green:boot", - .default_state = 1, - }, - [2] = { - .name = "omap3:red:user1", - .default_state = 0, - }, - [3] = { - .name = "omap3:green:user1", - .default_state = 0, - .gpio = -EINVAL, /* gets replaced */ - .active_low = 1, - }, -}; - -static struct gpio_led_platform_data igep_led_pdata = { - .leds = igep_gpio_leds, - .num_leds = ARRAY_SIZE(igep_gpio_leds), -}; - -static struct platform_device igep_led_device = { - .name = "leds-gpio", - .id = -1, - .dev = { - .platform_data = &igep_led_pdata, - }, -}; - -static void __init igep_leds_init(void) -{ - if (machine_is_igep0020()) { - igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED; - igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN; - igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED; - } else { - igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED; - igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN; - igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED; - } - - platform_device_register(&igep_led_device); -} - -#else -static struct gpio igep_gpio_leds[] __initdata = { - { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" }, - { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" }, - { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" }, -}; - -static inline void igep_leds_init(void) -{ - int i; - - if (machine_is_igep0020()) { - igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED; - igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN; - igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED; - } else { - igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED; - igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN; - igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED; - } - - if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) { - pr_warning("IGEP v2: Could not obtain leds gpios\n"); - return; - } - - for (i = 0; i < ARRAY_SIZE(igep_gpio_leds); i++) - gpio_export(igep_gpio_leds[i].gpio, 0); -} -#endif - -static struct gpio igep2_twl_gpios[] = { - { -EINVAL, GPIOF_IN, "GPIO_EHCI_NOC" }, - { -EINVAL, GPIOF_OUT_INIT_LOW, "GPIO_USBH_CPEN" }, -}; - -static int igep_twl_gpio_setup(struct device *dev, - unsigned gpio, unsigned ngpio) -{ - int ret; - - /* gpio + 0 is "mmc0_cd" (input/IRQ) */ - mmc[0].gpio_cd = gpio + 0; - omap_hsmmc_late_init(mmc); - - /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ -#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE) - ret = gpio_request_one(gpio + TWL4030_GPIO_MAX + 1, GPIOF_OUT_INIT_HIGH, - "gpio-led:green:d1"); - if (ret == 0) - gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0); - else - pr_warning("IGEP: Could not obtain gpio GPIO_LED1_GREEN\n"); -#else - igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1; -#endif - - if (machine_is_igep0030()) - return 0; - - /* - * REVISIT: need ehci-omap hooks for external VBUS - * power switch and overcurrent detect - */ - igep2_twl_gpios[0].gpio = gpio + 1; - - /* TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN (out, active low) */ - igep2_twl_gpios[1].gpio = gpio + TWL4030_GPIO_MAX; - - ret = gpio_request_array(igep2_twl_gpios, ARRAY_SIZE(igep2_twl_gpios)); - if (ret < 0) - pr_err("IGEP2: Could not obtain gpio for USBH_CPEN"); - - return 0; -}; - -static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = { - .use_leds = true, - .setup = igep_twl_gpio_setup, -}; - -static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = { - .name = "dvi", - .source = "tfp410.0", - .i2c_bus_num = 3, -}; - -static struct platform_device omap3stalker_dvi_connector_device = { - .name = "connector-dvi", - .id = 0, - .dev.platform_data = &omap3stalker_dvi_connector_pdata, -}; - -static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = { - .name = "tfp410.0", - .source = "dpi.0", - .data_lines = 24, - .power_down_gpio = IGEP2_GPIO_DVI_PUP, -}; - -static struct platform_device omap3stalker_tfp410_device = { - .name = "tfp410", - .id = 0, - .dev.platform_data = &omap3stalker_tfp410_pdata, -}; - -static struct omap_dss_board_info igep2_dss_data = { - .default_display_name = "dvi", -}; - -static struct platform_device *igep_devices[] __initdata = { - &igep_vwlan_device, - &omap3stalker_tfp410_device, - &omap3stalker_dvi_connector_device, -}; - -static int igep2_keymap[] = { - KEY(0, 0, KEY_LEFT), - KEY(0, 1, KEY_RIGHT), - KEY(0, 2, KEY_A), - KEY(0, 3, KEY_B), - KEY(1, 0, KEY_DOWN), - KEY(1, 1, KEY_UP), - KEY(1, 2, KEY_E), - KEY(1, 3, KEY_F), - KEY(2, 0, KEY_ENTER), - KEY(2, 1, KEY_I), - KEY(2, 2, KEY_J), - KEY(2, 3, KEY_K), - KEY(3, 0, KEY_M), - KEY(3, 1, KEY_N), - KEY(3, 2, KEY_O), - KEY(3, 3, KEY_P) -}; - -static struct matrix_keymap_data igep2_keymap_data = { - .keymap = igep2_keymap, - .keymap_size = ARRAY_SIZE(igep2_keymap), -}; - -static struct twl4030_keypad_data igep2_keypad_pdata = { - .keymap_data = &igep2_keymap_data, - .rows = 4, - .cols = 4, - .rep = 1, -}; - -static struct twl4030_platform_data igep_twldata = { - /* platform_data for children goes here */ - .gpio = &igep_twl4030_gpio_pdata, - .vmmc1 = &igep_vmmc1, - .vio = &igep_vio, -}; - -static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = { - { - I2C_BOARD_INFO("eeprom", 0x50), - }, -}; - -static void __init igep_i2c_init(void) -{ - int ret; - - omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_USB, - TWL_COMMON_REGULATOR_VPLL2); - igep_twldata.vpll2->constraints.apply_uV = true; - igep_twldata.vpll2->constraints.name = "VDVI"; - - if (machine_is_igep0020()) { - /* - * Bus 3 is attached to the DVI port where devices like the - * pico DLP projector don't work reliably with 400kHz - */ - ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo, - ARRAY_SIZE(igep2_i2c3_boardinfo)); - if (ret) - pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret); - - igep_twldata.keypad = &igep2_keypad_pdata; - /* Get common pmic data */ - omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO, 0); - } - - omap3_pmic_init("twl4030", &igep_twldata); -} - -static struct usbhs_phy_data igep2_phy_data[] __initdata = { - { - .port = 1, - .reset_gpio = IGEP2_GPIO_USBH_NRESET, - .vcc_gpio = -EINVAL, - }, -}; - -static struct usbhs_phy_data igep3_phy_data[] __initdata = { - { - .port = 2, - .reset_gpio = IGEP3_GPIO_USBH_NRESET, - .vcc_gpio = -EINVAL, - }, -}; - -static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = { - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, -}; - -static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = { - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, -}; - -#ifdef CONFIG_OMAP_MUX -static struct omap_board_mux board_mux[] __initdata = { - /* Display Sub System */ - OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), - /* TFP410 PanelBus DVI Transmitte (GPIO_170) */ - OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), - /* SMSC9221 LAN Controller ETH IRQ (GPIO_176) */ - OMAP3_MUX(MCSPI1_CS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; -#endif - -#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE) -static struct gpio igep_wlan_bt_gpios[] __initdata = { - { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NPD" }, - { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NRESET" }, - { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_BT_NRESET" }, -}; - -static void __init igep_wlan_bt_init(void) -{ - int err; - - /* GPIO's for WLAN-BT combo depends on hardware revision */ - if (hwrev == IGEP2_BOARD_HWREV_B) { - igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD; - igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET; - igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET; - } else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) { - igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD; - igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET; - igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET; - } else - return; - - /* Make sure that the GPIO pins are muxed correctly */ - omap_mux_init_gpio(igep_wlan_bt_gpios[0].gpio, OMAP_PIN_OUTPUT); - omap_mux_init_gpio(igep_wlan_bt_gpios[1].gpio, OMAP_PIN_OUTPUT); - omap_mux_init_gpio(igep_wlan_bt_gpios[2].gpio, OMAP_PIN_OUTPUT); - - err = gpio_request_array(igep_wlan_bt_gpios, - ARRAY_SIZE(igep_wlan_bt_gpios)); - if (err) { - pr_warning("IGEP2: Could not obtain WIFI/BT gpios\n"); - return; - } - - gpio_export(igep_wlan_bt_gpios[0].gpio, 0); - gpio_export(igep_wlan_bt_gpios[1].gpio, 0); - gpio_export(igep_wlan_bt_gpios[2].gpio, 0); - - gpio_set_value(igep_wlan_bt_gpios[1].gpio, 0); - udelay(10); - gpio_set_value(igep_wlan_bt_gpios[1].gpio, 1); - -} -#else -static inline void __init igep_wlan_bt_init(void) { } -#endif - -static struct regulator_consumer_supply dummy_supplies[] = { - REGULATOR_SUPPLY("vddvario", "smsc911x.0"), - REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), -}; - -static void __init igep_init(void) -{ - regulator_register_fixed(1, dummy_supplies, ARRAY_SIZE(dummy_supplies)); - omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); - - /* Get IGEP2 hardware revision */ - igep2_get_revision(); - - omap_hsmmc_init(mmc); - - /* Register I2C busses and drivers */ - igep_i2c_init(); - platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices)); - omap_serial_init(); - omap_sdrc_init(m65kxxxxam_sdrc_params, - m65kxxxxam_sdrc_params); - usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); - usb_musb_init(NULL); - - igep_flash_init(); - igep_leds_init(); - omap_twl4030_audio_init("igep2", NULL); - - /* - * WLAN-BT combo module from MuRata which has a Marvell WLAN - * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface. - */ - igep_wlan_bt_init(); - - if (machine_is_igep0020()) { - omap_display_init(&igep2_dss_data); - igep2_init_smsc911x(); - usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data)); - usbhs_init(&igep2_usbhs_bdata); - } else { - usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data)); - usbhs_init(&igep3_usbhs_bdata); - } -} - -MACHINE_START(IGEP0020, "IGEP v2 board") - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap35xx_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = igep_init, - .init_late = omap35xx_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END - -MACHINE_START(IGEP0030, "IGEP OMAP3 module") - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap35xx_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = igep_init, - .init_late = omap35xx_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index dd8da2c..4ec8d82 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -36,7 +36,6 @@ #include <asm/mach/map.h> #include "common.h" -#include "board-zoom.h" #include "gpmc.h" #include "gpmc-smsc911x.h" @@ -406,7 +405,7 @@ static void __init omap_ldp_init(void) usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); board_nand_init(ldp_nand_partitions, ARRAY_SIZE(ldp_nand_partitions), - ZOOM_NAND_CS, 0, nand_default_timings); + 0, 0, nand_default_timings); omap_hsmmc_init(mmc); ldp_display_init(); diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c deleted file mode 100644 index 1814387..0000000 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ /dev/null @@ -1,756 +0,0 @@ -/* - * linux/arch/arm/mach-omap2/board-omap3evm.c - * - * Copyright (C) 2008 Texas Instruments - * - * Modified from mach-omap2/board-3430sdp.c - * - * Initial code: Syed Mohammed Khasim - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/delay.h> -#include <linux/err.h> -#include <linux/clk.h> -#include <linux/gpio.h> -#include <linux/input.h> -#include <linux/input/matrix_keypad.h> -#include <linux/leds.h> -#include <linux/interrupt.h> - -#include <linux/mtd/mtd.h> -#include <linux/mtd/partitions.h> -#include <linux/mtd/nand.h> - -#include <linux/spi/spi.h> -#include <linux/spi/ads7846.h> -#include <linux/i2c/twl.h> -#include <linux/usb/otg.h> -#include <linux/usb/musb.h> -#include <linux/usb/usb_phy_gen_xceiv.h> -#include <linux/smsc911x.h> - -#include <linux/wl12xx.h> -#include <linux/regulator/fixed.h> -#include <linux/regulator/machine.h> -#include <linux/mmc/host.h> -#include <linux/export.h> -#include <linux/usb/phy.h> - -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <asm/mach/map.h> - -#include <linux/platform_data/mtd-nand-omap2.h> -#include "common.h" -#include <linux/platform_data/spi-omap2-mcspi.h> -#include <video/omapdss.h> -#include <video/omap-panel-data.h> - -#include "soc.h" -#include "mux.h" -#include "sdram-micron-mt46h32m32lf-6.h" -#include "hsmmc.h" -#include "common-board-devices.h" -#include "board-flash.h" - -#define NAND_CS 0 - -#define OMAP3_EVM_TS_GPIO 175 -#define OMAP3_EVM_EHCI_VBUS 22 -#define OMAP3_EVM_EHCI_SELECT 61 - -#define OMAP3EVM_ETHR_START 0x2c000000 -#define OMAP3EVM_ETHR_SIZE 1024 -#define OMAP3EVM_ETHR_ID_REV 0x50 -#define OMAP3EVM_ETHR_GPIO_IRQ 176 -#define OMAP3EVM_SMSC911X_CS 5 -/* - * Eth Reset signal - * 64 = Generation 1 (<=RevD) - * 7 = Generation 2 (>=RevE) - */ -#define OMAP3EVM_GEN1_ETHR_GPIO_RST 64 -#define OMAP3EVM_GEN2_ETHR_GPIO_RST 7 - -/* - * OMAP35x EVM revision - * Run time detection of EVM revision is done by reading Ethernet - * PHY ID - - * GEN_1 = 0x01150000 - * GEN_2 = 0x92200000 - */ -enum { - OMAP3EVM_BOARD_GEN_1 = 0, /* EVM Rev between A - D */ - OMAP3EVM_BOARD_GEN_2, /* EVM Rev >= Rev E */ -}; - -static u8 omap3_evm_version; - -static u8 get_omap3_evm_rev(void) -{ - return omap3_evm_version; -} - -static void __init omap3_evm_get_revision(void) -{ - void __iomem *ioaddr; - unsigned int smsc_id; - - /* Ethernet PHY ID is stored at ID_REV register */ - ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K); - if (!ioaddr) - return; - smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000; - iounmap(ioaddr); - - switch (smsc_id) { - /*SMSC9115 chipset*/ - case 0x01150000: - omap3_evm_version = OMAP3EVM_BOARD_GEN_1; - break; - /*SMSC 9220 chipset*/ - case 0x92200000: - default: - omap3_evm_version = OMAP3EVM_BOARD_GEN_2; - } -} - -#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) -#include "gpmc-smsc911x.h" - -static struct omap_smsc911x_platform_data smsc911x_cfg = { - .cs = OMAP3EVM_SMSC911X_CS, - .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ, - .gpio_reset = -EINVAL, - .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, -}; - -static inline void __init omap3evm_init_smsc911x(void) -{ - /* Configure ethernet controller reset gpio */ - if (cpu_is_omap3430()) { - if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) - smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST; - else - smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST; - } - - gpmc_smsc911x_init(&smsc911x_cfg); -} - -#else -static inline void __init omap3evm_init_smsc911x(void) { return; } -#endif - -/* - * OMAP3EVM LCD Panel control signals - */ -#define OMAP3EVM_LCD_PANEL_LR 2 -#define OMAP3EVM_LCD_PANEL_UD 3 -#define OMAP3EVM_LCD_PANEL_INI 152 -#define OMAP3EVM_LCD_PANEL_QVGA 154 -#define OMAP3EVM_LCD_PANEL_RESB 155 - -#define OMAP3EVM_LCD_PANEL_ENVDD 153 -#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210 - -/* - * OMAP3EVM DVI control signals - */ -#define OMAP3EVM_DVI_PANEL_EN_GPIO 199 - -#ifdef CONFIG_BROKEN -static void __init omap3_evm_display_init(void) -{ - int r; - - r = gpio_request_one(OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW, - "lcd_panel_envdd"); - if (r) - pr_err("failed to get lcd_panel_envdd GPIO\n"); - - r = gpio_request_one(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, - GPIOF_OUT_INIT_LOW, "lcd_panel_bklight"); - if (r) - pr_err("failed to get lcd_panel_bklight GPIO\n"); - - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) - gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0); - else - gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1); -} -#endif - -static struct panel_sharp_ls037v7dw01_platform_data omap3_evm_lcd_pdata = { - .name = "lcd", - .source = "dpi.0", - - .data_lines = 18, - - .resb_gpio = OMAP3EVM_LCD_PANEL_RESB, - .ini_gpio = OMAP3EVM_LCD_PANEL_INI, - .mo_gpio = OMAP3EVM_LCD_PANEL_QVGA, - .lr_gpio = OMAP3EVM_LCD_PANEL_LR, - .ud_gpio = OMAP3EVM_LCD_PANEL_UD, -}; - -static struct platform_device omap3_evm_lcd_device = { - .name = "panel-sharp-ls037v7dw01", - .id = 0, - .dev.platform_data = &omap3_evm_lcd_pdata, -}; - -static struct connector_dvi_platform_data omap3_evm_dvi_connector_pdata = { - .name = "dvi", - .source = "tfp410.0", - .i2c_bus_num = -1, -}; - -static struct platform_device omap3_evm_dvi_connector_device = { - .name = "connector-dvi", - .id = 0, - .dev.platform_data = &omap3_evm_dvi_connector_pdata, -}; - -static struct encoder_tfp410_platform_data omap3_evm_tfp410_pdata = { - .name = "tfp410.0", - .source = "dpi.0", - .data_lines = 24, - .power_down_gpio = OMAP3EVM_DVI_PANEL_EN_GPIO, -}; - -static struct platform_device omap3_evm_tfp410_device = { - .name = "tfp410", - .id = 0, - .dev.platform_data = &omap3_evm_tfp410_pdata, -}; - -static struct connector_atv_platform_data omap3_evm_tv_pdata = { - .name = "tv", - .source = "venc.0", - .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO, - .invert_polarity = false, -}; - -static struct platform_device omap3_evm_tv_connector_device = { - .name = "connector-analog-tv", - .id = 0, - .dev.platform_data = &omap3_evm_tv_pdata, -}; - -static struct omap_dss_board_info omap3_evm_dss_data = { - .default_display_name = "lcd", -}; - -static struct regulator_consumer_supply omap3evm_vmmc1_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"), -}; - -static struct regulator_consumer_supply omap3evm_vsim_supply[] = { - REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"), -}; - -/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */ -static struct regulator_init_data omap3evm_vmmc1 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 3150000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc1_supply), - .consumer_supplies = omap3evm_vmmc1_supply, -}; - -/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ -static struct regulator_init_data omap3evm_vsim = { - .constraints = { - .min_uV = 1800000, - .max_uV = 3000000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vsim_supply), - .consumer_supplies = omap3evm_vsim_supply, -}; - -static struct omap2_hsmmc_info mmc[] = { - { - .mmc = 1, - .caps = MMC_CAP_4_BIT_DATA, - .gpio_cd = -EINVAL, - .gpio_wp = 63, - .deferred = true, - }, -#ifdef CONFIG_WILINK_PLATFORM_DATA - { - .name = "wl1271", - .mmc = 2, - .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD, - .gpio_wp = -EINVAL, - .gpio_cd = -EINVAL, - .nonremovable = true, - }, -#endif - {} /* Terminator */ -}; - -static struct gpio_led gpio_leds[] = { - { - .name = "omap3evm::ledb", - /* normally not visible (board underside) */ - .default_trigger = "default-on", - .gpio = -EINVAL, /* gets replaced */ - .active_low = true, - }, -}; - -static struct gpio_led_platform_data gpio_led_info = { - .leds = gpio_leds, - .num_leds = ARRAY_SIZE(gpio_leds), -}; - -static struct platform_device leds_gpio = { - .name = "leds-gpio", - .id = -1, - .dev = { - .platform_data = &gpio_led_info, - }, -}; - - -static int omap3evm_twl_gpio_setup(struct device *dev, - unsigned gpio, unsigned ngpio) -{ - int r, lcd_bl_en; - - /* gpio + 0 is "mmc0_cd" (input/IRQ) */ - mmc[0].gpio_cd = gpio + 0; - omap_hsmmc_late_init(mmc); - - /* - * Most GPIOs are for USB OTG. Some are mostly sent to - * the P2 connector; notably LEDA for the LCD backlight. - */ - - /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */ - lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ? - GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; - r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL"); - if (r) - printk(KERN_ERR "failed to get/set lcd_bkl gpio\n"); - - /* gpio + 7 == DVI Enable */ - gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI"); - - /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ - gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1; - - platform_device_register(&leds_gpio); - - /* Enable VBUS switch by setting TWL4030.GPIO2DIR as output - * for starting USB tranceiver - */ -#ifdef CONFIG_TWL4030_CORE - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) { - u8 val; - - twl_i2c_read_u8(TWL4030_MODULE_GPIO, &val, REG_GPIODATADIR1); - val |= 0x04; /* TWL4030.GPIO2DIR BIT at GPIODATADIR1(0x9B) */ - twl_i2c_write_u8(TWL4030_MODULE_GPIO, val, REG_GPIODATADIR1); - } -#endif - - return 0; -} - -static struct twl4030_gpio_platform_data omap3evm_gpio_data = { - .use_leds = true, - .setup = omap3evm_twl_gpio_setup, -}; - -static uint32_t board_keymap[] = { - KEY(0, 0, KEY_LEFT), - KEY(0, 1, KEY_DOWN), - KEY(0, 2, KEY_ENTER), - KEY(0, 3, KEY_M), - - KEY(1, 0, KEY_RIGHT), - KEY(1, 1, KEY_UP), - KEY(1, 2, KEY_I), - KEY(1, 3, KEY_N), - - KEY(2, 0, KEY_A), - KEY(2, 1, KEY_E), - KEY(2, 2, KEY_J), - KEY(2, 3, KEY_O), - - KEY(3, 0, KEY_B), - KEY(3, 1, KEY_F), - KEY(3, 2, KEY_K), - KEY(3, 3, KEY_P) -}; - -static struct matrix_keymap_data board_map_data = { - .keymap = board_keymap, - .keymap_size = ARRAY_SIZE(board_keymap), -}; - -static struct twl4030_keypad_data omap3evm_kp_data = { - .keymap_data = &board_map_data, - .rows = 4, - .cols = 4, - .rep = 1, -}; - -/* ads7846 on SPI */ -static struct regulator_consumer_supply omap3evm_vio_supply[] = { - REGULATOR_SUPPLY("vcc", "spi1.0"), -}; - -/* VIO for ads7846 */ -static struct regulator_init_data omap3evm_vio = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vio_supply), - .consumer_supplies = omap3evm_vio_supply, -}; - -#ifdef CONFIG_WILINK_PLATFORM_DATA - -#define OMAP3EVM_WLAN_PMENA_GPIO (150) -#define OMAP3EVM_WLAN_IRQ_GPIO (149) - -static struct regulator_consumer_supply omap3evm_vmmc2_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"), -}; - -/* VMMC2 for driving the WL12xx module */ -static struct regulator_init_data omap3evm_vmmc2 = { - .constraints = { - .valid_ops_mask = REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc2_supply), - .consumer_supplies = omap3evm_vmmc2_supply, -}; - -static struct fixed_voltage_config omap3evm_vwlan = { - .supply_name = "vwl1271", - .microvolts = 1800000, /* 1.80V */ - .gpio = OMAP3EVM_WLAN_PMENA_GPIO, - .startup_delay = 70000, /* 70ms */ - .enable_high = 1, - .enabled_at_boot = 0, - .init_data = &omap3evm_vmmc2, -}; - -static struct platform_device omap3evm_wlan_regulator = { - .name = "reg-fixed-voltage", - .id = 1, - .dev = { - .platform_data = &omap3evm_vwlan, - }, -}; - -struct wl12xx_platform_data omap3evm_wlan_data __initdata = { - .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */ -}; -#endif - -/* VAUX2 for USB */ -static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = { - REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */ - REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */ - REGULATOR_SUPPLY("vcc", "usb_phy_gen_xceiv.2"), /* hsusb port 2 */ - REGULATOR_SUPPLY("vaux2", NULL), -}; - -static struct regulator_init_data omap3evm_vaux2 = { - .constraints = { - .min_uV = 2800000, - .max_uV = 2800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3evm_vaux2_supplies), - .consumer_supplies = omap3evm_vaux2_supplies, -}; - -static struct twl4030_platform_data omap3evm_twldata = { - /* platform_data for children goes here */ - .keypad = &omap3evm_kp_data, - .gpio = &omap3evm_gpio_data, - .vio = &omap3evm_vio, - .vmmc1 = &omap3evm_vmmc1, - .vsim = &omap3evm_vsim, -}; - -static int __init omap3_evm_i2c_init(void) -{ - omap3_pmic_get_config(&omap3evm_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | - TWL_COMMON_PDATA_AUDIO, - TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); - - omap3evm_twldata.vdac->constraints.apply_uV = true; - omap3evm_twldata.vpll2->constraints.apply_uV = true; - - omap3_pmic_init("twl4030", &omap3evm_twldata); - omap_register_i2c_bus(2, 400, NULL, 0); - omap_register_i2c_bus(3, 400, NULL, 0); - return 0; -} - -static struct usbhs_phy_data phy_data[] __initdata = { - { - .port = 2, - .reset_gpio = -1, /* set at runtime */ - .vcc_gpio = -EINVAL, - }, -}; - -static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, -}; - -#ifdef CONFIG_OMAP_MUX -static struct omap_board_mux omap35x_board_mux[] __initdata = { - OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_NONE), - OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_NONE), -#ifdef CONFIG_WILINK_PLATFORM_DATA - /* WLAN IRQ - GPIO 149 */ - OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), - - /* WLAN POWER ENABLE - GPIO 150 */ - OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), - - /* MMC2 SDIO pin muxes for WL12xx */ - OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), -#endif - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; - -static struct omap_board_mux omap36x_board_mux[] __initdata = { - OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | - OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW | - OMAP_PIN_OFF_WAKEUPENABLE), - /* AM/DM37x EVM: DSS data bus muxed with sys_boot */ - OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT0, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT1, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT3, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), - OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE), -#ifdef CONFIG_WILINK_PLATFORM_DATA - /* WLAN IRQ - GPIO 149 */ - OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), - - /* WLAN POWER ENABLE - GPIO 150 */ - OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), - - /* MMC2 SDIO pin muxes for WL12xx */ - OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP), -#endif - - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; -#else -#define omap35x_board_mux NULL -#define omap36x_board_mux NULL -#endif - -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, - .mode = MUSB_OTG, - .power = 100, -}; - -static struct gpio omap3_evm_ehci_gpios[] __initdata = { - { OMAP3_EVM_EHCI_VBUS, GPIOF_OUT_INIT_HIGH, "enable EHCI VBUS" }, - { OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW, "select EHCI port" }, -}; - -static void __init omap3_evm_wl12xx_init(void) -{ -#ifdef CONFIG_WILINK_PLATFORM_DATA - int ret; - - /* WL12xx WLAN Init */ - omap3evm_wlan_data.irq = gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO); - ret = wl12xx_set_platform_data(&omap3evm_wlan_data); - if (ret) - pr_err("error setting wl12xx data: %d\n", ret); - ret = platform_device_register(&omap3evm_wlan_regulator); - if (ret) - pr_err("error registering wl12xx device: %d\n", ret); -#endif -} - -static struct regulator_consumer_supply dummy_supplies[] = { - REGULATOR_SUPPLY("vddvario", "smsc911x.0"), - REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), -}; - -static struct mtd_partition omap3evm_nand_partitions[] = { - /* All the partition sizes are listed in terms of NAND block size */ - { - .name = "X-Loader", - .offset = 0, - .size = 4*(SZ_128K), - .mask_flags = MTD_WRITEABLE - }, - { - .name = "U-Boot", - .offset = MTDPART_OFS_APPEND, - .size = 14*(SZ_128K), - .mask_flags = MTD_WRITEABLE - }, - { - .name = "U-Boot Env", - .offset = MTDPART_OFS_APPEND, - .size = 2*(SZ_128K) - }, - { - .name = "Kernel", - .offset = MTDPART_OFS_APPEND, - .size = 40*(SZ_128K) - }, - { - .name = "File system", - .size = MTDPART_SIZ_FULL, - .offset = MTDPART_OFS_APPEND, - }, -}; - -static void __init omap3_evm_init(void) -{ - struct omap_board_mux *obm; - - omap3_evm_get_revision(); - regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); - - obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux; - omap3_mux_init(obm, OMAP_PACKAGE_CBB); - - omap_mux_init_gpio(63, OMAP_PIN_INPUT); - omap_hsmmc_init(mmc); - - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) - omap3evm_twldata.vaux2 = &omap3evm_vaux2; - - omap3_evm_i2c_init(); - - omap_display_init(&omap3_evm_dss_data); - platform_device_register(&omap3_evm_lcd_device); - platform_device_register(&omap3_evm_tfp410_device); - platform_device_register(&omap3_evm_dvi_connector_device); - platform_device_register(&omap3_evm_tv_connector_device); - - omap_serial_init(); - omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL); - - /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ - usb_nop_xceiv_register(); - - if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) { - /* enable EHCI VBUS using GPIO22 */ - omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP); - /* Select EHCI port on main board */ - omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT, - OMAP_PIN_INPUT_PULLUP); - gpio_request_array(omap3_evm_ehci_gpios, - ARRAY_SIZE(omap3_evm_ehci_gpios)); - - /* setup EHCI phy reset config */ - omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP); - phy_data[0].reset_gpio = 21; - - /* EVM REV >= E can supply 500mA with EXTVBUS programming */ - musb_board_data.power = 500; - musb_board_data.extvbus = 1; - } else { - /* setup EHCI phy reset on MDC */ - omap_mux_init_gpio(135, OMAP_PIN_OUTPUT); - phy_data[0].reset_gpio = 135; - } - usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); - usb_musb_init(&musb_board_data); - - usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); - usbhs_init(&usbhs_bdata); - board_nand_init(omap3evm_nand_partitions, - ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS, - NAND_BUSWIDTH_16, NULL); - - omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL); - omap3evm_init_smsc911x(); -#ifdef CONFIG_BROKEN - omap3_evm_display_init(); -#endif - omap3_evm_wl12xx_init(); - omap_twl4030_audio_init("omap3evm", NULL); -} - -MACHINE_START(OMAP3EVM, "OMAP3 EVM") - /* Maintainer: Syed Mohammed Khasim - Texas Instruments */ - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap35xx_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = omap3_evm_init, - .init_late = omap35xx_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END diff --git a/arch/arm/mach-omap2/board-rm680.c b/arch/arm/mach-omap2/board-rm680.c deleted file mode 100644 index 345e8c4..0000000 --- a/arch/arm/mach-omap2/board-rm680.c +++ /dev/null @@ -1,167 +0,0 @@ -/* - * Board support file for Nokia N950 (RM-680) / N9 (RM-696). - * - * Copyright (C) 2010 Nokia - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/io.h> -#include <linux/i2c.h> -#include <linux/gpio.h> -#include <linux/init.h> -#include <linux/i2c/twl.h> -#include <linux/platform_device.h> -#include <linux/regulator/fixed.h> -#include <linux/regulator/machine.h> -#include <linux/regulator/consumer.h> -#include <linux/platform_data/mtd-onenand-omap2.h> -#include <linux/usb/phy.h> - -#include <asm/mach/arch.h> -#include <asm/mach-types.h> - -#include "common.h" -#include "mux.h" -#include "gpmc.h" -#include "mmc.h" -#include "hsmmc.h" -#include "sdram-nokia.h" -#include "common-board-devices.h" -#include "gpmc-onenand.h" - -static struct regulator_consumer_supply rm680_vemmc_consumers[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"), -}; - -/* Fixed regulator for internal eMMC */ -static struct regulator_init_data rm680_vemmc = { - .constraints = { - .name = "rm680_vemmc", - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_STATUS - | REGULATOR_CHANGE_MODE, - }, - .num_consumer_supplies = ARRAY_SIZE(rm680_vemmc_consumers), - .consumer_supplies = rm680_vemmc_consumers, -}; - -static struct fixed_voltage_config rm680_vemmc_config = { - .supply_name = "VEMMC", - .microvolts = 2900000, - .gpio = 157, - .startup_delay = 150, - .enable_high = 1, - .init_data = &rm680_vemmc, -}; - -static struct platform_device rm680_vemmc_device = { - .name = "reg-fixed-voltage", - .dev = { - .platform_data = &rm680_vemmc_config, - }, -}; - -static struct platform_device *rm680_peripherals_devices[] __initdata = { - &rm680_vemmc_device, -}; - -/* TWL */ -static struct twl4030_gpio_platform_data rm680_gpio_data = { - .pullups = BIT(0), - .pulldowns = BIT(1) | BIT(2) | BIT(8) | BIT(15), -}; - -static struct twl4030_platform_data rm680_twl_data = { - .gpio = &rm680_gpio_data, - /* add rest of the children here */ -}; - -static void __init rm680_i2c_init(void) -{ - omap3_pmic_get_config(&rm680_twl_data, TWL_COMMON_PDATA_USB, 0); - omap_pmic_init(1, 2900, "twl5031", 7 + OMAP_INTC_START, &rm680_twl_data); - omap_register_i2c_bus(2, 400, NULL, 0); - omap_register_i2c_bus(3, 400, NULL, 0); -} - -#if defined(CONFIG_MTD_ONENAND_OMAP2) || \ - defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) -static struct omap_onenand_platform_data board_onenand_data[] = { - { - .gpio_irq = 65, - .flags = ONENAND_SYNC_READWRITE, - } -}; -#endif - -/* eMMC */ -static struct omap2_hsmmc_info mmc[] __initdata = { - { - .name = "internal", - .mmc = 2, - .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MMC_HIGHSPEED, - .gpio_cd = -EINVAL, - .gpio_wp = -EINVAL, - }, - { /* Terminator */ } -}; - -static void __init rm680_peripherals_init(void) -{ - platform_add_devices(rm680_peripherals_devices, - ARRAY_SIZE(rm680_peripherals_devices)); - rm680_i2c_init(); - gpmc_onenand_init(board_onenand_data); - omap_hsmmc_init(mmc); -} - -#ifdef CONFIG_OMAP_MUX -static struct omap_board_mux board_mux[] __initdata = { - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; -#endif - -static void __init rm680_init(void) -{ - struct omap_sdrc_params *sdrc_params; - - omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); - omap_serial_init(); - - sdrc_params = nokia_get_sdram_timings(); - omap_sdrc_init(sdrc_params, sdrc_params); - - usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); - usb_musb_init(NULL); - rm680_peripherals_init(); -} - -MACHINE_START(NOKIA_RM680, "Nokia RM-680 board") - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap3630_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = rm680_init, - .init_late = omap3630_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END - -MACHINE_START(NOKIA_RM696, "Nokia RM-696 board") - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap3630_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = rm680_init, - .init_late = omap3630_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END diff --git a/arch/arm/mach-omap2/board-zoom-debugboard.c b/arch/arm/mach-omap2/board-zoom-debugboard.c deleted file mode 100644 index 42e5f23..0000000 --- a/arch/arm/mach-omap2/board-zoom-debugboard.c +++ /dev/null @@ -1,139 +0,0 @@ -/* - * Copyright (C) 2009 Texas Instruments Inc. - * Mikkel Christensen <mlc@ti.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/gpio.h> -#include <linux/serial_8250.h> -#include <linux/smsc911x.h> -#include <linux/interrupt.h> - -#include <linux/regulator/fixed.h> -#include <linux/regulator/machine.h> - -#include "gpmc.h" -#include "gpmc-smsc911x.h" - -#include "board-zoom.h" - -#include "soc.h" -#include "common.h" - -#define ZOOM_SMSC911X_CS 7 -#define ZOOM_SMSC911X_GPIO 158 -#define ZOOM_QUADUART_CS 3 -#define ZOOM_QUADUART_GPIO 102 -#define ZOOM_QUADUART_RST_GPIO 152 -#define QUART_CLK 1843200 -#define DEBUG_BASE 0x08000000 -#define ZOOM_ETHR_START DEBUG_BASE - -static struct omap_smsc911x_platform_data zoom_smsc911x_cfg = { - .cs = ZOOM_SMSC911X_CS, - .gpio_irq = ZOOM_SMSC911X_GPIO, - .gpio_reset = -EINVAL, - .flags = SMSC911X_USE_32BIT, -}; - -static inline void __init zoom_init_smsc911x(void) -{ - gpmc_smsc911x_init(&zoom_smsc911x_cfg); -} - -static struct plat_serial8250_port serial_platform_data[] = { - { - .mapbase = ZOOM_UART_BASE, - .flags = UPF_BOOT_AUTOCONF|UPF_IOREMAP|UPF_SHARE_IRQ, - .irqflags = IRQF_SHARED | IRQF_TRIGGER_RISING, - .iotype = UPIO_MEM, - .regshift = 1, - .uartclk = QUART_CLK, - }, { - .flags = 0 - } -}; - -static struct platform_device zoom_debugboard_serial_device = { - .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM, - .dev = { - .platform_data = serial_platform_data, - }, -}; - -static inline void __init zoom_init_quaduart(void) -{ - int quart_cs; - unsigned long cs_mem_base; - int quart_gpio = 0; - - if (gpio_request_one(ZOOM_QUADUART_RST_GPIO, - GPIOF_OUT_INIT_LOW, - "TL16CP754C GPIO") < 0) { - pr_err("Failed to request GPIO%d for TL16CP754C\n", - ZOOM_QUADUART_RST_GPIO); - return; - } - - quart_cs = ZOOM_QUADUART_CS; - - if (gpmc_cs_request(quart_cs, SZ_1M, &cs_mem_base) < 0) { - pr_err("Failed to request GPMC mem for Quad UART(TL16CP754C)\n"); - return; - } - - quart_gpio = ZOOM_QUADUART_GPIO; - - if (gpio_request_one(quart_gpio, GPIOF_IN, "TL16CP754C GPIO") < 0) - printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n", - quart_gpio); - - serial_platform_data[0].irq = gpio_to_irq(102); -} - -static inline int omap_zoom_debugboard_detect(void) -{ - int debug_board_detect = 0; - int ret = 1; - - debug_board_detect = ZOOM_SMSC911X_GPIO; - - if (gpio_request_one(debug_board_detect, GPIOF_IN, - "Zoom debug board detect") < 0) { - pr_err("Failed to request GPIO%d for Zoom debug board detect\n", - debug_board_detect); - return 0; - } - - if (!gpio_get_value(debug_board_detect)) { - ret = 0; - } - gpio_free(debug_board_detect); - return ret; -} - -static struct platform_device *zoom_devices[] __initdata = { - &zoom_debugboard_serial_device, -}; - -static struct regulator_consumer_supply dummy_supplies[] = { - REGULATOR_SUPPLY("vddvario", "smsc911x.0"), - REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), -}; - -int __init zoom_debugboard_init(void) -{ - if (!omap_zoom_debugboard_detect()) - return 0; - - regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); - zoom_init_smsc911x(); - zoom_init_quaduart(); - return platform_add_devices(zoom_devices, ARRAY_SIZE(zoom_devices)); -} diff --git a/arch/arm/mach-omap2/board-zoom-display.c b/arch/arm/mach-omap2/board-zoom-display.c deleted file mode 100644 index 3d8ecc1e..0000000 --- a/arch/arm/mach-omap2/board-zoom-display.c +++ /dev/null @@ -1,71 +0,0 @@ -/* - * Copyright (C) 2010 Texas Instruments Inc. - * - * Modified from mach-omap2/board-zoom-peripherals.c - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/gpio.h> -#include <linux/spi/spi.h> -#include <linux/platform_data/spi-omap2-mcspi.h> -#include <video/omapdss.h> -#include <video/omap-panel-data.h> - -#include "board-zoom.h" -#include "soc.h" -#include "common.h" - -#define LCD_PANEL_RESET_GPIO_PROD 96 -#define LCD_PANEL_RESET_GPIO_PILOT 55 -#define LCD_PANEL_QVGA_GPIO 56 - -static struct panel_nec_nl8048hl11_platform_data zoom_lcd_pdata = { - .name = "lcd", - .source = "dpi.0", - - .data_lines = 24, - - .res_gpio = -1, /* filled in code */ - .qvga_gpio = LCD_PANEL_QVGA_GPIO, -}; - -static struct omap_dss_board_info zoom_dss_data = { - .default_display_name = "lcd", -}; - -static void __init zoom_lcd_panel_init(void) -{ - zoom_lcd_pdata.res_gpio = (omap_rev() > OMAP3430_REV_ES3_0) ? - LCD_PANEL_RESET_GPIO_PROD : - LCD_PANEL_RESET_GPIO_PILOT; -} - -static struct omap2_mcspi_device_config dss_lcd_mcspi_config = { - .turbo_mode = 1, -}; - -static struct spi_board_info nec_8048_spi_board_info[] __initdata = { - [0] = { - .modalias = "panel-nec-nl8048hl11", - .bus_num = 1, - .chip_select = 2, - .max_speed_hz = 375000, - .controller_data = &dss_lcd_mcspi_config, - .platform_data = &zoom_lcd_pdata, - }, -}; - -void __init zoom_display_init(void) -{ - omap_display_init(&zoom_dss_data); - zoom_lcd_panel_init(); - spi_register_board_info(nec_8048_spi_board_info, - ARRAY_SIZE(nec_8048_spi_board_info)); -} - diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c deleted file mode 100644 index a90375d..0000000 --- a/arch/arm/mach-omap2/board-zoom-peripherals.c +++ /dev/null @@ -1,360 +0,0 @@ -/* - * Copyright (C) 2009 Texas Instruments Inc. - * - * Modified from mach-omap2/board-zoom2.c - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/input.h> -#include <linux/input/matrix_keypad.h> -#include <linux/gpio.h> -#include <linux/i2c/twl.h> -#include <linux/regulator/machine.h> -#include <linux/regulator/fixed.h> -#include <linux/wl12xx.h> -#include <linux/mmc/host.h> -#include <linux/platform_data/gpio-omap.h> -#include <linux/platform_data/omap-twl4030.h> -#include <linux/usb/phy.h> -#include <linux/pwm.h> -#include <linux/leds_pwm.h> -#include <linux/pwm_backlight.h> - -#include <asm/mach-types.h> -#include <asm/mach/arch.h> -#include <asm/mach/map.h> - -#include "common.h" - -#include "board-zoom.h" - -#include "mux.h" -#include "hsmmc.h" -#include "common-board-devices.h" - -#define OMAP_ZOOM_WLAN_PMENA_GPIO (101) -#define OMAP_ZOOM_TSC2004_IRQ_GPIO (153) -#define OMAP_ZOOM_WLAN_IRQ_GPIO (162) - -/* Zoom2 has Qwerty keyboard*/ -static uint32_t board_keymap[] = { - KEY(0, 0, KEY_E), - KEY(0, 1, KEY_R), - KEY(0, 2, KEY_T), - KEY(0, 3, KEY_HOME), - KEY(0, 6, KEY_I), - KEY(0, 7, KEY_LEFTSHIFT), - KEY(1, 0, KEY_D), - KEY(1, 1, KEY_F), - KEY(1, 2, KEY_G), - KEY(1, 3, KEY_SEND), - KEY(1, 6, KEY_K), - KEY(1, 7, KEY_ENTER), - KEY(2, 0, KEY_X), - KEY(2, 1, KEY_C), - KEY(2, 2, KEY_V), - KEY(2, 3, KEY_END), - KEY(2, 6, KEY_DOT), - KEY(2, 7, KEY_CAPSLOCK), - KEY(3, 0, KEY_Z), - KEY(3, 1, KEY_KPPLUS), - KEY(3, 2, KEY_B), - KEY(3, 3, KEY_F1), - KEY(3, 6, KEY_O), - KEY(3, 7, KEY_SPACE), - KEY(4, 0, KEY_W), - KEY(4, 1, KEY_Y), - KEY(4, 2, KEY_U), - KEY(4, 3, KEY_F2), - KEY(4, 4, KEY_VOLUMEUP), - KEY(4, 6, KEY_L), - KEY(4, 7, KEY_LEFT), - KEY(5, 0, KEY_S), - KEY(5, 1, KEY_H), - KEY(5, 2, KEY_J), - KEY(5, 3, KEY_F3), - KEY(5, 4, KEY_UNKNOWN), - KEY(5, 5, KEY_VOLUMEDOWN), - KEY(5, 6, KEY_M), - KEY(5, 7, KEY_RIGHT), - KEY(6, 0, KEY_Q), - KEY(6, 1, KEY_A), - KEY(6, 2, KEY_N), - KEY(6, 3, KEY_BACKSPACE), - KEY(6, 6, KEY_P), - KEY(6, 7, KEY_UP), - KEY(7, 0, KEY_PROG1), /*MACRO 1 <User defined> */ - KEY(7, 1, KEY_PROG2), /*MACRO 2 <User defined> */ - KEY(7, 2, KEY_PROG3), /*MACRO 3 <User defined> */ - KEY(7, 3, KEY_PROG4), /*MACRO 4 <User defined> */ - KEY(7, 6, KEY_SELECT), - KEY(7, 7, KEY_DOWN) -}; - -static struct matrix_keymap_data board_map_data = { - .keymap = board_keymap, - .keymap_size = ARRAY_SIZE(board_keymap), -}; - -static struct twl4030_keypad_data zoom_kp_twl4030_data = { - .keymap_data = &board_map_data, - .rows = 8, - .cols = 8, - .rep = 1, -}; - -static struct regulator_consumer_supply zoom_vmmc1_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"), -}; - -static struct regulator_consumer_supply zoom_vsim_supply[] = { - REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"), -}; - -static struct regulator_consumer_supply zoom_vmmc2_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"), -}; - -static struct regulator_consumer_supply zoom_vmmc3_supply[] = { - REGULATOR_SUPPLY("vmmc", "omap_hsmmc.2"), -}; - -/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */ -static struct regulator_init_data zoom_vmmc1 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 3150000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(zoom_vmmc1_supply), - .consumer_supplies = zoom_vmmc1_supply, -}; - -/* VMMC2 for MMC2 card */ -static struct regulator_init_data zoom_vmmc2 = { - .constraints = { - .min_uV = 1850000, - .max_uV = 1850000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(zoom_vmmc2_supply), - .consumer_supplies = zoom_vmmc2_supply, -}; - -/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */ -static struct regulator_init_data zoom_vsim = { - .constraints = { - .min_uV = 1800000, - .max_uV = 3000000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(zoom_vsim_supply), - .consumer_supplies = zoom_vsim_supply, -}; - -static struct regulator_init_data zoom_vmmc3 = { - .constraints = { - .valid_ops_mask = REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(zoom_vmmc3_supply), - .consumer_supplies = zoom_vmmc3_supply, -}; - -static struct fixed_voltage_config zoom_vwlan = { - .supply_name = "vwl1271", - .microvolts = 1800000, /* 1.8V */ - .gpio = OMAP_ZOOM_WLAN_PMENA_GPIO, - .startup_delay = 70000, /* 70msec */ - .enable_high = 1, - .enabled_at_boot = 0, - .init_data = &zoom_vmmc3, -}; - -static struct platform_device omap_vwlan_device = { - .name = "reg-fixed-voltage", - .id = 1, - .dev = { - .platform_data = &zoom_vwlan, - }, -}; - -static struct pwm_lookup zoom_pwm_lookup[] = { - PWM_LOOKUP("twl-pwm", 0, "leds_pwm", "zoom::keypad"), - PWM_LOOKUP("twl-pwm", 1, "pwm-backlight", "backlight"), -}; - -static struct led_pwm zoom_pwm_leds[] = { - { - .name = "zoom::keypad", - .max_brightness = 127, - .pwm_period_ns = 7812500, - }, -}; - -static struct led_pwm_platform_data zoom_pwm_data = { - .num_leds = ARRAY_SIZE(zoom_pwm_leds), - .leds = zoom_pwm_leds, -}; - -static struct platform_device zoom_leds_pwm = { - .name = "leds_pwm", - .id = -1, - .dev = { - .platform_data = &zoom_pwm_data, - }, -}; - -static struct platform_pwm_backlight_data zoom_backlight_data = { - .pwm_id = 1, - .max_brightness = 127, - .dft_brightness = 127, - .pwm_period_ns = 7812500, -}; - -static struct platform_device zoom_backlight_pwm = { - .name = "pwm-backlight", - .id = -1, - .dev = { - .platform_data = &zoom_backlight_data, - }, -}; - -static struct platform_device *zoom_devices[] __initdata = { - &omap_vwlan_device, - &zoom_leds_pwm, - &zoom_backlight_pwm, -}; - -static struct wl12xx_platform_data omap_zoom_wlan_data __initdata = { - .board_ref_clock = WL12XX_REFCLOCK_26, /* 26 MHz */ -}; - -static struct omap2_hsmmc_info mmc[] = { - { - .name = "external", - .mmc = 1, - .caps = MMC_CAP_4_BIT_DATA, - .gpio_wp = -EINVAL, - .power_saving = true, - .deferred = true, - }, - { - .name = "internal", - .mmc = 2, - .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, - .gpio_cd = -EINVAL, - .gpio_wp = -EINVAL, - .nonremovable = true, - .power_saving = true, - }, - { - .name = "wl1271", - .mmc = 3, - .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD, - .gpio_wp = -EINVAL, - .gpio_cd = -EINVAL, - .nonremovable = true, - }, - {} /* Terminator */ -}; - -static struct omap_tw4030_pdata omap_twl4030_audio_data = { - .voice_connected = true, - .custom_routing = true, - - .has_hs = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT, - .has_hf = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT, - - .has_mainmic = true, - .has_submic = true, - .has_hsmic = true, - .has_linein = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT, -}; - -static int zoom_twl_gpio_setup(struct device *dev, - unsigned gpio, unsigned ngpio) -{ - /* gpio + 0 is "mmc0_cd" (input/IRQ) */ - mmc[0].gpio_cd = gpio + 0; - omap_hsmmc_late_init(mmc); - - /* Audio setup */ - omap_twl4030_audio_data.jack_detect = gpio + 2; - omap_twl4030_audio_init("Zoom2", &omap_twl4030_audio_data); - - return 0; -} - -static struct twl4030_gpio_platform_data zoom_gpio_data = { - .setup = zoom_twl_gpio_setup, -}; - -static struct twl4030_platform_data zoom_twldata = { - /* platform_data for children goes here */ - .gpio = &zoom_gpio_data, - .keypad = &zoom_kp_twl4030_data, - .vmmc1 = &zoom_vmmc1, - .vmmc2 = &zoom_vmmc2, - .vsim = &zoom_vsim, -}; - -static int __init omap_i2c_init(void) -{ - omap3_pmic_get_config(&zoom_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI | - TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO, - TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); - - if (machine_is_omap_zoom2()) - zoom_twldata.audio->codec->ramp_delay_value = 3; /* 161 ms */ - - omap_pmic_init(1, 2400, "twl5030", 7 + OMAP_INTC_START, &zoom_twldata); - omap_register_i2c_bus(2, 400, NULL, 0); - omap_register_i2c_bus(3, 400, NULL, 0); - return 0; -} - -static void enable_board_wakeup_source(void) -{ - /* T2 interrupt line (keypad) */ - omap_mux_init_signal("sys_nirq", - OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP); -} - -void __init zoom_peripherals_init(void) -{ - int ret; - - omap_zoom_wlan_data.irq = gpio_to_irq(OMAP_ZOOM_WLAN_IRQ_GPIO); - ret = wl12xx_set_platform_data(&omap_zoom_wlan_data); - - if (ret) - pr_err("error setting wl12xx data: %d\n", ret); - - omap_hsmmc_init(mmc); - omap_i2c_init(); - pwm_add_table(zoom_pwm_lookup, ARRAY_SIZE(zoom_pwm_lookup)); - platform_add_devices(zoom_devices, ARRAY_SIZE(zoom_devices)); - usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); - usb_musb_init(NULL); - enable_board_wakeup_source(); - omap_serial_init(); -} diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c deleted file mode 100644 index 1a3dd86..0000000 --- a/arch/arm/mach-omap2/board-zoom.c +++ /dev/null @@ -1,159 +0,0 @@ -/* - * Copyright (C) 2009-2010 Texas Instruments Inc. - * Mikkel Christensen <mlc@ti.com> - * Felipe Balbi <balbi@ti.com> - * - * Modified from mach-omap2/board-ldp.c - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/platform_device.h> -#include <linux/input.h> -#include <linux/gpio.h> -#include <linux/i2c/twl.h> -#include <linux/mtd/nand.h> - -#include <asm/mach-types.h> -#include <asm/mach/arch.h> - -#include "common.h" - -#include "board-zoom.h" - -#include "board-flash.h" -#include "mux.h" -#include "sdram-micron-mt46h32m32lf-6.h" -#include "sdram-hynix-h8mbx00u0mer-0em.h" - -#define ZOOM3_EHCI_RESET_GPIO 64 - -#ifdef CONFIG_OMAP_MUX -static struct omap_board_mux board_mux[] __initdata = { - /* WLAN IRQ - GPIO 162 */ - OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT), - /* WLAN POWER ENABLE - GPIO 101 */ - OMAP3_MUX(CAM_D2, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), - /* WLAN SDIO: MMC3 CMD */ - OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLUP), - /* WLAN SDIO: MMC3 CLK */ - OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP), - /* WLAN SDIO: MMC3 DAT[0-3] */ - OMAP3_MUX(ETK_D3, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(ETK_D4, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(ETK_D5, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP), - OMAP3_MUX(ETK_D6, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP), - { .reg_offset = OMAP_MUX_TERMINATOR }, -}; -#endif - -static struct mtd_partition zoom_nand_partitions[] = { - /* All the partition sizes are listed in terms of NAND block size */ - { - .name = "X-Loader-NAND", - .offset = 0, - .size = 4 * (64 * 2048), /* 512KB, 0x80000 */ - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - { - .name = "U-Boot-NAND", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */ - .size = 10 * (64 * 2048), /* 1.25MB, 0x140000 */ - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - { - .name = "Boot Env-NAND", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x1c0000 */ - .size = 2 * (64 * 2048), /* 256KB, 0x40000 */ - }, - { - .name = "Kernel-NAND", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x0200000*/ - .size = 240 * (64 * 2048), /* 30M, 0x1E00000 */ - }, - { - .name = "system", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x2000000 */ - .size = 3328 * (64 * 2048), /* 416M, 0x1A000000 */ - }, - { - .name = "userdata", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x1C000000*/ - .size = 256 * (64 * 2048), /* 32M, 0x2000000 */ - }, - { - .name = "cache", - .offset = MTDPART_OFS_APPEND, /* Offset = 0x1E000000*/ - .size = 256 * (64 * 2048), /* 32M, 0x2000000 */ - }, -}; - -static struct usbhs_phy_data phy_data[] __initdata = { - { - .port = 2, - .reset_gpio = ZOOM3_EHCI_RESET_GPIO, - .vcc_gpio = -EINVAL, - }, -}; - -static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, -}; - -static void __init omap_zoom_init(void) -{ - if (machine_is_omap_zoom2()) { - omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); - } else if (machine_is_omap_zoom3()) { - omap3_mux_init(board_mux, OMAP_PACKAGE_CBP); - omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT); - - usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); - usbhs_init(&usbhs_bdata); - } - - board_nand_init(zoom_nand_partitions, - ARRAY_SIZE(zoom_nand_partitions), ZOOM_NAND_CS, - NAND_BUSWIDTH_16, nand_default_timings); - zoom_debugboard_init(); - zoom_peripherals_init(); - - if (machine_is_omap_zoom2()) - omap_sdrc_init(mt46h32m32lf6_sdrc_params, - mt46h32m32lf6_sdrc_params); - else if (machine_is_omap_zoom3()) - omap_sdrc_init(h8mbx00u0mer0em_sdrc_params, - h8mbx00u0mer0em_sdrc_params); - - zoom_display_init(); -} - -MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board") - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap3430_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = omap_zoom_init, - .init_late = omap3430_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END - -MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board") - .atag_offset = 0x100, - .reserve = omap_reserve, - .map_io = omap3_map_io, - .init_early = omap3630_init_early, - .init_irq = omap3_init_irq, - .handle_irq = omap3_intc_handle_irq, - .init_machine = omap_zoom_init, - .init_late = omap3630_init_late, - .init_time = omap3_sync32k_timer_init, - .restart = omap3xxx_restart, -MACHINE_END diff --git a/arch/arm/mach-omap2/board-zoom.h b/arch/arm/mach-omap2/board-zoom.h deleted file mode 100644 index 2e94869..0000000 --- a/arch/arm/mach-omap2/board-zoom.h +++ /dev/null @@ -1,10 +0,0 @@ -/* - * Defines for zoom boards - */ -#include <video/omapdss.h> - -#define ZOOM_NAND_CS 0 - -extern int __init zoom_debugboard_init(void); -extern void __init zoom_peripherals_init(void); -extern void __init zoom_display_init(void); diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index 4a5684b..f7644fe 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -98,6 +98,7 @@ void am35xx_init_early(void); void ti81xx_init_early(void); void am33xx_init_early(void); void am43xx_init_early(void); +void am43xx_init_late(void); void omap4430_init_early(void); void omap5_init_early(void); void omap3_init_late(void); /* Do not use this one */ @@ -109,8 +110,11 @@ void omap35xx_init_late(void); void omap3630_init_late(void); void am35xx_init_late(void); void ti81xx_init_late(void); +void am33xx_init_late(void); +void omap5_init_late(void); int omap2_common_pm_late_init(void); void dra7xx_init_early(void); +void dra7xx_init_late(void); #ifdef CONFIG_SOC_BUS void omap_soc_device_init(void); @@ -288,6 +292,9 @@ static inline void omap4_cpu_resume(void) #endif +void pdata_quirks_init(struct of_device_id *); +void omap_pcs_legacy_init(int irq, void (*rearm)(void)); + struct omap_sdrc_params; extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0, struct omap_sdrc_params *sdrc_cs1); diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 89a8698..0dd6398 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -19,7 +19,6 @@ #include <linux/of.h> #include <linux/pinctrl/machine.h> #include <linux/platform_data/omap4-keypad.h> -#include <linux/wl12xx.h> #include <linux/platform_data/mailbox-omap.h> #include <asm/mach-types.h> @@ -476,40 +475,6 @@ int __init omap_init_vout(void) int __init omap_init_vout(void) { return 0; } #endif -#if IS_ENABLED(CONFIG_WL12XX) - -static struct wl12xx_platform_data wl12xx __initdata; - -void __init omap_init_wl12xx_of(void) -{ - int ret; - - if (!of_have_populated_dt()) - return; - - if (of_machine_is_compatible("ti,omap4-sdp")) { - wl12xx.board_ref_clock = WL12XX_REFCLOCK_26; - wl12xx.board_tcxo_clock = WL12XX_TCXOCLOCK_26; - wl12xx.irq = gpio_to_irq(53); - } else if (of_machine_is_compatible("ti,omap4-panda")) { - wl12xx.board_ref_clock = WL12XX_REFCLOCK_38; - wl12xx.irq = gpio_to_irq(53); - } else { - return; - } - - ret = wl12xx_set_platform_data(&wl12xx); - if (ret) { - pr_err("error setting wl12xx data: %d\n", ret); - return; - } -} -#else -static inline void omap_init_wl12xx_of(void) -{ -} -#endif - /*-------------------------------------------------------------------------*/ static int __init omap2_init_devices(void) @@ -532,9 +497,6 @@ static int __init omap2_init_devices(void) omap_init_sham(); omap_init_aes(); omap_init_rng(); - } else { - /* These can be removed when bindings are done */ - omap_init_wl12xx_of(); } omap_init_sti(); diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c index bf89eff..365bfd3 100644 --- a/arch/arm/mach-omap2/dss-common.c +++ b/arch/arm/mach-omap2/dss-common.c @@ -213,3 +213,47 @@ void __init omap_4430sdp_display_init_of(void) platform_device_register(&sdp4430_tpd_device); platform_device_register(&sdp4430_hdmi_connector_device); } + + +/* OMAP3 IGEPv2 data */ + +#define IGEP2_DVI_TFP410_POWER_DOWN_GPIO 170 + +/* DVI Connector */ +static struct connector_dvi_platform_data omap3_igep2_dvi_connector_pdata = { + .name = "dvi", + .source = "tfp410.0", + .i2c_bus_num = 3, +}; + +static struct platform_device omap3_igep2_dvi_connector_device = { + .name = "connector-dvi", + .id = 0, + .dev.platform_data = &omap3_igep2_dvi_connector_pdata, +}; + +/* TFP410 DPI-to-DVI chip */ +static struct encoder_tfp410_platform_data omap3_igep2_tfp410_pdata = { + .name = "tfp410.0", + .source = "dpi.0", + .data_lines = 24, + .power_down_gpio = IGEP2_DVI_TFP410_POWER_DOWN_GPIO, +}; + +static struct platform_device omap3_igep2_tfp410_device = { + .name = "tfp410", + .id = 0, + .dev.platform_data = &omap3_igep2_tfp410_pdata, +}; + +static struct omap_dss_board_info igep2_dss_data = { + .default_display_name = "dvi", +}; + +void __init omap3_igep2_display_init_of(void) +{ + omap_display_init(&igep2_dss_data); + + platform_device_register(&omap3_igep2_tfp410_device); + platform_device_register(&omap3_igep2_dvi_connector_device); +} diff --git a/arch/arm/mach-omap2/dss-common.h b/arch/arm/mach-omap2/dss-common.h index c28fe3c..a9becf0 100644 --- a/arch/arm/mach-omap2/dss-common.h +++ b/arch/arm/mach-omap2/dss-common.h @@ -8,5 +8,6 @@ void __init omap4_panda_display_init_of(void); void __init omap_4430sdp_display_init_of(void); +void __init omap3_igep2_display_init_of(void); #endif diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 579697a..51525fa 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -1521,6 +1521,42 @@ err: return ret; } +/* + * REVISIT: Add timing support from slls644g.pdf + */ +static int gpmc_probe_8250(struct platform_device *pdev, + struct device_node *child) +{ + struct resource res; + unsigned long base; + int ret, cs; + + if (of_property_read_u32(child, "reg", &cs) < 0) { + dev_err(&pdev->dev, "%s has no 'reg' property\n", + child->full_name); + return -ENODEV; + } + + if (of_address_to_resource(child, 0, &res) < 0) { + dev_err(&pdev->dev, "%s has malformed 'reg' property\n", + child->full_name); + return -ENODEV; + } + + ret = gpmc_cs_request(cs, resource_size(&res), &base); + if (ret < 0) { + dev_err(&pdev->dev, "cannot request GPMC CS %d\n", cs); + return ret; + } + + if (of_platform_device_create(child, NULL, &pdev->dev)) + return 0; + + dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name); + + return -ENODEV; +} + static int gpmc_probe_dt(struct platform_device *pdev) { int ret; @@ -1564,6 +1600,8 @@ static int gpmc_probe_dt(struct platform_device *pdev) else if (of_node_cmp(child->name, "ethernet") == 0 || of_node_cmp(child->name, "nor") == 0) ret = gpmc_probe_generic_child(pdev, child); + else if (of_node_cmp(child->name, "8250") == 0) + ret = gpmc_probe_8250(pdev, child); if (WARN(ret < 0, "%s: probing gpmc child %s failed\n", __func__, child->full_name)) diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index c90f647..cd22262 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -583,6 +583,11 @@ void __init am33xx_init_early(void) omap_hwmod_init_postsetup(); omap_clk_init = am33xx_clk_init; } + +void __init am33xx_init_late(void) +{ + omap_common_late_init(); +} #endif #ifdef CONFIG_SOC_AM43XX @@ -602,6 +607,11 @@ void __init am43xx_init_early(void) am43xx_hwmod_init(); omap_hwmod_init_postsetup(); } + +void __init am43xx_init_late(void) +{ + omap_common_late_init(); +} #endif #ifdef CONFIG_ARCH_OMAP4 @@ -657,6 +667,11 @@ void __init omap5_init_early(void) omap54xx_hwmod_init(); omap_hwmod_init_postsetup(); } + +void __init omap5_init_late(void) +{ + omap_common_late_init(); +} #endif #ifdef CONFIG_SOC_DRA7XX @@ -677,6 +692,11 @@ void __init dra7xx_init_early(void) dra7xx_hwmod_init(); omap_hwmod_init_postsetup(); } + +void __init dra7xx_init_late(void) +{ + omap_common_late_init(); +} #endif diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index f82cf87..48094b5 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -811,6 +811,12 @@ int __init omap_mux_late_init(void) } } + omap_mux_dbg_init(); + + /* see pinctrl-single-omap for the wake-up interrupt handling */ + if (of_have_populated_dt()) + return 0; + ret = request_irq(omap_prcm_event_to_irq("io"), omap_hwmod_mux_handle_irq, IRQF_SHARED | IRQF_NO_SUSPEND, "hwmod_io", omap_mux_late_init); @@ -818,8 +824,6 @@ int __init omap_mux_late_init(void) if (ret) pr_warning("mux: Failed to setup hwmod io irq %d\n", ret); - omap_mux_dbg_init(); - return 0; } diff --git a/arch/arm/mach-omap2/opp.c b/arch/arm/mach-omap2/opp.c index bd41d59..82fd8c7 100644 --- a/arch/arm/mach-omap2/opp.c +++ b/arch/arm/mach-omap2/opp.c @@ -17,6 +17,7 @@ * GNU General Public License for more details. */ #include <linux/module.h> +#include <linux/of.h> #include <linux/opp.h> #include <linux/cpu.h> @@ -40,6 +41,9 @@ int __init omap_init_opp_table(struct omap_opp_def *opp_def, { int i, r; + if (of_have_populated_dt()) + return -EINVAL; + if (!opp_def || !opp_def_size) { pr_err("%s: invalid params!\n", __func__); return -EINVAL; diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c new file mode 100644 index 0000000..10c7145 --- /dev/null +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -0,0 +1,174 @@ +/* + * Legacy platform_data quirks + * + * Copyright (C) 2013 Texas Instruments + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/clk.h> +#include <linux/gpio.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/of_platform.h> +#include <linux/wl12xx.h> + +#include <linux/platform_data/pinctrl-single.h> + +#include "common.h" +#include "common-board-devices.h" +#include "dss-common.h" +#include "control.h" + +struct pdata_init { + const char *compatible; + void (*fn)(void); +}; + +/* + * Create alias for USB host PHY clock. + * Remove this when clock phandle can be provided via DT + */ +static void __init __used legacy_init_ehci_clk(char *clkname) +{ + int ret; + + ret = clk_add_alias("main_clk", NULL, clkname, NULL); + if (ret) + pr_err("%s:Failed to add main_clk alias to %s :%d\n", + __func__, clkname, ret); +} + +#if IS_ENABLED(CONFIG_WL12XX) + +static struct wl12xx_platform_data wl12xx __initdata; + +static void __init __used legacy_init_wl12xx(unsigned ref_clock, + unsigned tcxo_clock, + int gpio) +{ + int res; + + wl12xx.board_ref_clock = ref_clock; + wl12xx.board_tcxo_clock = tcxo_clock; + wl12xx.irq = gpio_to_irq(gpio); + + res = wl12xx_set_platform_data(&wl12xx); + if (res) { + pr_err("error setting wl12xx data: %d\n", res); + return; + } +} +#else +static inline void legacy_init_wl12xx(unsigned ref_clock, + unsigned tcxo_clock, + int gpio) +{ +} +#endif + +#ifdef CONFIG_ARCH_OMAP3 +static void __init hsmmc2_internal_input_clk(void) +{ + u32 reg; + + reg = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1); + reg |= OMAP2_MMCSDIO2ADPCLKISEL; + omap_ctrl_writel(reg, OMAP343X_CONTROL_DEVCONF1); +} + +static void __init omap3_igep0020_legacy_init(void) +{ + omap3_igep2_display_init_of(); +} + +static void __init omap3_evm_legacy_init(void) +{ + legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 149); +} + +static void __init omap3_zoom_legacy_init(void) +{ + legacy_init_wl12xx(WL12XX_REFCLOCK_26, 0, 162); +} +#endif /* CONFIG_ARCH_OMAP3 */ + +#ifdef CONFIG_ARCH_OMAP4 +static void __init omap4_sdp_legacy_init(void) +{ + omap_4430sdp_display_init_of(); + legacy_init_wl12xx(WL12XX_REFCLOCK_26, + WL12XX_TCXOCLOCK_26, 53); +} + +static void __init omap4_panda_legacy_init(void) +{ + omap4_panda_display_init_of(); + legacy_init_ehci_clk("auxclk3_ck"); + legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53); +} +#endif + +#ifdef CONFIG_SOC_OMAP5 +static void __init omap5_uevm_legacy_init(void) +{ + legacy_init_ehci_clk("auxclk1_ck"); +} +#endif + +static struct pcs_pdata pcs_pdata; + +void omap_pcs_legacy_init(int irq, void (*rearm)(void)) +{ + pcs_pdata.irq = irq; + pcs_pdata.rearm = rearm; +} + +struct of_dev_auxdata omap_auxdata_lookup[] __initdata = { +#ifdef CONFIG_ARCH_OMAP3 + OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002030, "48002030.pinmux", &pcs_pdata), + OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002a00, "48002a00.pinmux", &pcs_pdata), +#endif +#ifdef CONFIG_ARCH_OMAP4 + OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a100040, "4a100040.pinmux", &pcs_pdata), + OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a31e040, "4a31e040.pinmux", &pcs_pdata), +#endif + { /* sentinel */ }, +}; + +static struct pdata_init pdata_quirks[] __initdata = { +#ifdef CONFIG_ARCH_OMAP3 + { "nokia,omap3-n9", hsmmc2_internal_input_clk, }, + { "nokia,omap3-n950", hsmmc2_internal_input_clk, }, + { "isee,omap3-igep0020", omap3_igep0020_legacy_init, }, + { "ti,omap3-evm-37xx", omap3_evm_legacy_init, }, + { "ti,omap3-zoom3", omap3_zoom_legacy_init, }, +#endif +#ifdef CONFIG_ARCH_OMAP4 + { "ti,omap4-sdp", omap4_sdp_legacy_init, }, + { "ti,omap4-panda", omap4_panda_legacy_init, }, +#endif +#ifdef CONFIG_SOC_OMAP5 + { "ti,omap5-uevm", omap5_uevm_legacy_init, }, +#endif + { /* sentinel */ }, +}; + +void __init pdata_quirks_init(struct of_device_id *omap_dt_match_table) +{ + struct pdata_init *quirks = pdata_quirks; + + omap_sdrc_init(NULL, NULL); + of_platform_populate(NULL, omap_dt_match_table, + omap_auxdata_lookup, NULL); + + while (quirks->compatible) { + if (of_machine_is_compatible(quirks->compatible)) { + if (quirks->fn) + quirks->fn(); + break; + } + quirks++; + } +} diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index e742118..360b2da 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -266,7 +266,12 @@ static void __init omap4_init_voltages(void) static inline void omap_init_cpufreq(void) { - struct platform_device_info devinfo = { .name = "omap-cpufreq", }; + struct platform_device_info devinfo = { }; + + if (!of_have_populated_dt()) + devinfo.name = "omap-cpufreq"; + else + devinfo.name = "cpufreq-cpu0"; platform_device_register_full(&devinfo); } @@ -300,10 +305,11 @@ int __init omap2_common_pm_late_init(void) /* Smartreflex device init */ omap_devinit_smartreflex(); - /* cpufreq dummy device instantiation */ - omap_init_cpufreq(); } + /* cpufreq dummy device instantiation */ + omap_init_cpufreq(); + #ifdef CONFIG_SUSPEND suspend_set_ops(&omap_pm_ops); #endif diff --git a/arch/arm/mach-omap2/prm3xxx.h b/arch/arm/mach-omap2/prm3xxx.h index 277f717..f8eb833 100644 --- a/arch/arm/mach-omap2/prm3xxx.h +++ b/arch/arm/mach-omap2/prm3xxx.h @@ -144,7 +144,13 @@ extern u32 omap3_prm_vcvp_read(u8 offset); extern void omap3_prm_vcvp_write(u32 val, u8 offset); extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset); -extern void omap3xxx_prm_reconfigure_io_chain(void); +#ifdef CONFIG_ARCH_OMAP3 +void omap3xxx_prm_reconfigure_io_chain(void); +#else +static inline void omap3xxx_prm_reconfigure_io_chain(void) +{ +} +#endif /* PRM interrupt-related functions */ extern void omap3xxx_prm_read_pending_irqs(unsigned long *events); diff --git a/arch/arm/mach-omap2/prm44xx_54xx.h b/arch/arm/mach-omap2/prm44xx_54xx.h index 7cd22ab..a085d9c 100644 --- a/arch/arm/mach-omap2/prm44xx_54xx.h +++ b/arch/arm/mach-omap2/prm44xx_54xx.h @@ -42,7 +42,13 @@ extern u32 omap4_prm_vcvp_read(u8 offset); extern void omap4_prm_vcvp_write(u32 val, u8 offset); extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset); -extern void omap44xx_prm_reconfigure_io_chain(void); +#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) +void omap44xx_prm_reconfigure_io_chain(void); +#else +static inline void omap44xx_prm_reconfigure_io_chain(void) +{ +} +#endif /* PRM interrupt-related functions */ extern void omap44xx_prm_read_pending_irqs(unsigned long *events); diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c index 228b850..a2e1174 100644 --- a/arch/arm/mach-omap2/prm_common.c +++ b/arch/arm/mach-omap2/prm_common.c @@ -24,6 +24,7 @@ #include <linux/interrupt.h> #include <linux/slab.h> +#include "soc.h" #include "prm2xxx_3xxx.h" #include "prm2xxx.h" #include "prm3xxx.h" @@ -322,6 +323,16 @@ int omap_prcm_register_chain_handler(struct omap_prcm_irq_setup *irq_setup) prcm_irq_chips[i] = gc; } + if (of_have_populated_dt()) { + int irq = omap_prcm_event_to_irq("io"); + if (cpu_is_omap34xx()) + omap_pcs_legacy_init(irq, + omap3xxx_prm_reconfigure_io_chain); + else + omap_pcs_legacy_init(irq, + omap44xx_prm_reconfigure_io_chain); + } + return 0; err: diff --git a/arch/arm/mach-s3c64xx/Kconfig b/arch/arm/mach-s3c64xx/Kconfig index a2d5bb3..2cb8dc5 100644 --- a/arch/arm/mach-s3c64xx/Kconfig +++ b/arch/arm/mach-s3c64xx/Kconfig @@ -298,4 +298,20 @@ config MACH_WLF_CRAGG_6410 help Machine support for the Wolfson Cragganmore S3C6410 variant. +config MACH_S3C64XX_DT + bool "Samsung S3C6400/S3C6410 machine using Device Tree" + select CLKSRC_OF + select CPU_S3C6400 + select CPU_S3C6410 + select PINCTRL + select PINCTRL_S3C64XX + select USE_OF + help + Machine support for Samsung S3C6400/S3C6410 machines with Device Tree + enabled. + Select this if a fdt blob is available for your S3C64XX SoC based + board. + Note: This is under development and not all peripherals can be + supported with this machine file. + endif diff --git a/arch/arm/mach-s3c64xx/Makefile b/arch/arm/mach-s3c64xx/Makefile index 645a8fe..6faedcf 100644 --- a/arch/arm/mach-s3c64xx/Makefile +++ b/arch/arm/mach-s3c64xx/Makefile @@ -57,3 +57,4 @@ obj-$(CONFIG_MACH_SMARTQ7) += mach-smartq7.o obj-$(CONFIG_MACH_SMDK6400) += mach-smdk6400.o obj-$(CONFIG_MACH_SMDK6410) += mach-smdk6410.o obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o mach-crag6410-module.o +obj-$(CONFIG_MACH_S3C64XX_DT) += mach-s3c64xx-dt.o diff --git a/arch/arm/mach-s3c64xx/common.c b/arch/arm/mach-s3c64xx/common.c index 7d3cb58..7a3ce4c 100644 --- a/arch/arm/mach-s3c64xx/common.c +++ b/arch/arm/mach-s3c64xx/common.c @@ -14,6 +14,10 @@ * published by the Free Software Foundation. */ +/* + * NOTE: Code in this file is not used when booting with Device Tree support. + */ + #include <linux/kernel.h> #include <linux/init.h> #include <linux/module.h> @@ -203,6 +207,10 @@ void __init s3c64xx_init_io(struct map_desc *mach_desc, int size) static __init int s3c64xx_dev_init(void) { + /* Not applicable when using DT. */ + if (of_have_populated_dt()) + return 0; + subsys_system_register(&s3c64xx_subsys, NULL); return device_register(&s3c64xx_dev); } @@ -404,6 +412,10 @@ static int __init s3c64xx_init_irq_eint(void) { int irq; + /* On DT-enabled systems EINTs are handled by pinctrl-s3c64xx driver. */ + if (of_have_populated_dt()) + return -ENODEV; + for (irq = IRQ_EINT(0); irq <= IRQ_EINT(27); irq++) { irq_set_chip_and_handler(irq, &s3c_irq_eint, handle_level_irq); irq_set_chip_data(irq, (void *)eint_irq_to_bit(irq)); diff --git a/arch/arm/mach-s3c64xx/dma.c b/arch/arm/mach-s3c64xx/dma.c index c511dfa..7e22c21 100644 --- a/arch/arm/mach-s3c64xx/dma.c +++ b/arch/arm/mach-s3c64xx/dma.c @@ -12,6 +12,10 @@ * published by the Free Software Foundation. */ +/* + * NOTE: Code in this file is not used when booting with Device Tree support. + */ + #include <linux/kernel.h> #include <linux/module.h> #include <linux/interrupt.h> @@ -24,6 +28,7 @@ #include <linux/err.h> #include <linux/io.h> #include <linux/amba/pl080.h> +#include <linux/of.h> #include <mach/dma.h> #include <mach/map.h> @@ -726,6 +731,10 @@ static int __init s3c64xx_dma_init(void) { int ret; + /* This driver is not supported when booting with device tree. */ + if (of_have_populated_dt()) + return -ENODEV; + printk(KERN_INFO "%s: Registering DMA channels\n", __func__); dma_pool = dma_pool_create("DMA-LLI", NULL, sizeof(struct pl080s_lli), 16, 0); diff --git a/arch/arm/mach-s3c64xx/irq-pm.c b/arch/arm/mach-s3c64xx/irq-pm.c index c3da1b6..1649c0d 100644 --- a/arch/arm/mach-s3c64xx/irq-pm.c +++ b/arch/arm/mach-s3c64xx/irq-pm.c @@ -12,12 +12,17 @@ * published by the Free Software Foundation. */ +/* + * NOTE: Code in this file is not used when booting with Device Tree support. + */ + #include <linux/kernel.h> #include <linux/syscore_ops.h> #include <linux/interrupt.h> #include <linux/serial_core.h> #include <linux/irq.h> #include <linux/io.h> +#include <linux/of.h> #include <mach/map.h> @@ -101,6 +106,10 @@ static struct syscore_ops s3c64xx_irq_syscore_ops = { static __init int s3c64xx_syscore_init(void) { + /* Appropriate drivers (pinctrl, uart) handle this when using DT. */ + if (of_have_populated_dt()) + return 0; + register_syscore_ops(&s3c64xx_irq_syscore_ops); return 0; diff --git a/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c b/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c new file mode 100644 index 0000000..7eb9a10 --- /dev/null +++ b/arch/arm/mach-s3c64xx/mach-s3c64xx-dt.c @@ -0,0 +1,85 @@ +/* + * Samsung's S3C64XX flattened device tree enabled machine + * + * Copyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/clk-provider.h> +#include <linux/irqchip.h> +#include <linux/of_platform.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/system_misc.h> + +#include <plat/cpu.h> +#include <plat/watchdog-reset.h> + +#include <mach/map.h> + +#include "common.h" + +/* + * IO mapping for shared system controller IP. + * + * FIXME: Make remaining drivers use dynamic mapping. + */ +static struct map_desc s3c64xx_dt_iodesc[] __initdata = { + { + .virtual = (unsigned long)S3C_VA_SYS, + .pfn = __phys_to_pfn(S3C64XX_PA_SYSCON), + .length = SZ_4K, + .type = MT_DEVICE, + }, +}; + +static void __init s3c64xx_dt_map_io(void) +{ + debug_ll_io_init(); + iotable_init(s3c64xx_dt_iodesc, ARRAY_SIZE(s3c64xx_dt_iodesc)); + + s3c64xx_init_cpu(); + + if (!soc_is_s3c64xx()) + panic("SoC is not S3C64xx!"); +} + +static void __init s3c64xx_dt_init_irq(void) +{ + of_clk_init(NULL); + samsung_wdt_reset_of_init(); + irqchip_init(); +}; + +static void __init s3c64xx_dt_init_machine(void) +{ + of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); +} + +static void s3c64xx_dt_restart(enum reboot_mode mode, const char *cmd) +{ + if (mode != REBOOT_SOFT) + samsung_wdt_reset(); + + /* if all else fails, or mode was for soft, jump to 0 */ + soft_restart(0); +} + +static char const *s3c64xx_dt_compat[] __initdata = { + "samsung,s3c6400", + "samsung,s3c6410", + NULL +}; + +DT_MACHINE_START(S3C6400_DT, "Samsung S3C64xx (Flattened Device Tree)") + /* Maintainer: Tomasz Figa <tomasz.figa@gmail.com> */ + .dt_compat = s3c64xx_dt_compat, + .map_io = s3c64xx_dt_map_io, + .init_irq = s3c64xx_dt_init_irq, + .init_machine = s3c64xx_dt_init_machine, + .restart = s3c64xx_dt_restart, +MACHINE_END diff --git a/arch/arm/mach-s3c64xx/s3c6400.c b/arch/arm/mach-s3c64xx/s3c6400.c index 331fe8e..3db0c98 100644 --- a/arch/arm/mach-s3c64xx/s3c6400.c +++ b/arch/arm/mach-s3c64xx/s3c6400.c @@ -9,6 +9,10 @@ * published by the Free Software Foundation. */ +/* + * NOTE: Code in this file is not used when booting with Device Tree support. + */ + #include <linux/kernel.h> #include <linux/types.h> #include <linux/interrupt.h> @@ -20,6 +24,7 @@ #include <linux/device.h> #include <linux/serial_core.h> #include <linux/platform_device.h> +#include <linux/of.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> @@ -76,6 +81,10 @@ static struct device s3c6400_dev = { static int __init s3c6400_core_init(void) { + /* Not applicable when using DT. */ + if (of_have_populated_dt()) + return 0; + return subsys_system_register(&s3c6400_subsys, NULL); } diff --git a/arch/arm/mach-s3c64xx/s3c6410.c b/arch/arm/mach-s3c64xx/s3c6410.c index 7e6fa12..72b2278 100644 --- a/arch/arm/mach-s3c64xx/s3c6410.c +++ b/arch/arm/mach-s3c64xx/s3c6410.c @@ -10,6 +10,10 @@ * published by the Free Software Foundation. */ +/* + * NOTE: Code in this file is not used when booting with Device Tree support. + */ + #include <linux/kernel.h> #include <linux/types.h> #include <linux/interrupt.h> @@ -21,6 +25,7 @@ #include <linux/device.h> #include <linux/serial_core.h> #include <linux/platform_device.h> +#include <linux/of.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> @@ -79,6 +84,10 @@ static struct device s3c6410_dev = { static int __init s3c6410_core_init(void) { + /* Not applicable when using DT. */ + if (of_have_populated_dt()) + return 0; + return subsys_system_register(&s3c6410_subsys, NULL); } diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile index fe1f3e2..616b96e 100644 --- a/arch/arm/mach-ux500/Makefile +++ b/arch/arm/mach-ux500/Makefile @@ -2,14 +2,11 @@ # Makefile for the linux kernel, U8500 machine. # -obj-y := cpu.o devices.o devices-common.o \ - id.o usb.o timer.o pm.o +obj-y := cpu.o devices.o id.o timer.o pm.o obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o devices-db8500.o obj-$(CONFIG_MACH_MOP500) += board-mop500.o board-mop500-sdi.o \ board-mop500-regulators.o \ - board-mop500-uib.o board-mop500-stuib.o \ - board-mop500-u8500uib.o \ board-mop500-pins.o \ board-mop500-audio.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o diff --git a/arch/arm/mach-ux500/board-mop500-audio.c b/arch/arm/mach-ux500/board-mop500-audio.c index ec08072..154e15f 100644 --- a/arch/arm/mach-ux500/board-mop500-audio.c +++ b/arch/arm/mach-ux500/board-mop500-audio.c @@ -68,40 +68,6 @@ static struct stedma40_chan_cfg msp2_dma_tx = { .phy_channel = 1, }; -static struct platform_device *db8500_add_msp_i2s(struct device *parent, - int id, - resource_size_t base, int irq, - struct msp_i2s_platform_data *pdata) -{ - struct platform_device *pdev; - struct resource res[] = { - DEFINE_RES_MEM(base, SZ_4K), - DEFINE_RES_IRQ(irq), - }; - - pr_info("Register platform-device 'ux500-msp-i2s', id %d, irq %d\n", - id, irq); - pdev = platform_device_register_resndata(parent, "ux500-msp-i2s", id, - res, ARRAY_SIZE(res), - pdata, sizeof(*pdata)); - if (!pdev) { - pr_err("Failed to register platform-device 'ux500-msp-i2s.%d'!\n", - id); - return NULL; - } - - return pdev; -} - -/* Platform device for ASoC MOP500 machine */ -static struct platform_device snd_soc_mop500 = { - .name = "snd-soc-mop500", - .id = 0, - .dev = { - .platform_data = NULL, - }, -}; - struct msp_i2s_platform_data msp2_platform_data = { .id = MSP_I2S_2, .msp_i2s_dma_rx = &msp2_dma_rx, @@ -113,19 +79,3 @@ struct msp_i2s_platform_data msp3_platform_data = { .msp_i2s_dma_rx = &msp1_dma_rx, .msp_i2s_dma_tx = NULL, }; - -void mop500_audio_init(struct device *parent) -{ - pr_info("%s: Register platform-device 'snd-soc-mop500'.\n", __func__); - platform_device_register(&snd_soc_mop500); - - pr_info("Initialize MSP I2S-devices.\n"); - db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0, - &msp0_platform_data); - db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1, - &msp1_platform_data); - db8500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2, - &msp2_platform_data); - db8500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1, - &msp3_platform_data); -} diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c index b3e61a3..26600a1 100644 --- a/arch/arm/mach-ux500/board-mop500-sdi.c +++ b/arch/arm/mach-ux500/board-mop500-sdi.c @@ -65,18 +65,6 @@ struct mmci_platform_data mop500_sdi0_data = { #endif }; -static void sdi0_configure(struct device *parent) -{ - /* Add the device, force v2 to subrevision 1 */ - db8500_add_sdi0(parent, &mop500_sdi0_data, U8500_SDI_V2_PERIPHID); -} - -void mop500_sdi_tc35892_init(struct device *parent) -{ - mop500_sdi0_data.gpio_cd = GPIO_SDMMC_CD; - sdi0_configure(parent); -} - /* * SDI1 (SDIO WLAN) */ @@ -178,42 +166,3 @@ struct mmci_platform_data mop500_sdi4_data = { .dma_tx_param = &mop500_sdi4_dma_cfg_tx, #endif }; - -void __init mop500_sdi_init(struct device *parent) -{ - /* PoP:ed eMMC */ - db8500_add_sdi2(parent, &mop500_sdi2_data, U8500_SDI_V2_PERIPHID); - /* On-board eMMC */ - db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID); - - /* - * On boards with the TC35892 GPIO expander, sdi0 will finally - * be added when the TC35892 initializes and calls - * mop500_sdi_tc35892_init() above. - */ -} - -void __init snowball_sdi_init(struct device *parent) -{ - /* On Snowball MMC_CAP_SD_HIGHSPEED isn't supported (Hardware issue?) */ - mop500_sdi0_data.capabilities &= ~MMC_CAP_SD_HIGHSPEED; - /* On-board eMMC */ - db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID); - /* External Micro SD slot */ - mop500_sdi0_data.gpio_cd = SNOWBALL_SDMMC_CD_GPIO; - mop500_sdi0_data.cd_invert = true; - sdi0_configure(parent); -} - -void __init hrefv60_sdi_init(struct device *parent) -{ - /* PoP:ed eMMC */ - db8500_add_sdi2(parent, &mop500_sdi2_data, U8500_SDI_V2_PERIPHID); - /* On-board eMMC */ - db8500_add_sdi4(parent, &mop500_sdi4_data, U8500_SDI_V2_PERIPHID); - /* External Micro SD slot */ - mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO; - sdi0_configure(parent); - /* WLAN SDIO channel */ - db8500_add_sdi1(parent, &mop500_sdi1_data, U8500_SDI_V2_PERIPHID); -} diff --git a/arch/arm/mach-ux500/board-mop500-stuib.c b/arch/arm/mach-ux500/board-mop500-stuib.c deleted file mode 100644 index 7e1f294..0000000 --- a/arch/arm/mach-ux500/board-mop500-stuib.c +++ /dev/null @@ -1,120 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * License terms: GNU General Public License (GPL), version 2 - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/mfd/stmpe.h> -#include <linux/input/bu21013.h> -#include <linux/gpio.h> -#include <linux/interrupt.h> -#include <linux/i2c.h> -#include <linux/input/matrix_keypad.h> -#include <asm/mach-types.h> - -#include "board-mop500.h" - -/* STMPE/SKE keypad use this key layout */ -static const unsigned int mop500_keymap[] = { - KEY(2, 5, KEY_END), - KEY(4, 1, KEY_POWER), - KEY(3, 5, KEY_VOLUMEDOWN), - KEY(1, 3, KEY_3), - KEY(5, 2, KEY_RIGHT), - KEY(5, 0, KEY_9), - - KEY(0, 5, KEY_MENU), - KEY(7, 6, KEY_ENTER), - KEY(4, 5, KEY_0), - KEY(6, 7, KEY_2), - KEY(3, 4, KEY_UP), - KEY(3, 3, KEY_DOWN), - - KEY(6, 4, KEY_SEND), - KEY(6, 2, KEY_BACK), - KEY(4, 2, KEY_VOLUMEUP), - KEY(5, 5, KEY_1), - KEY(4, 3, KEY_LEFT), - KEY(3, 2, KEY_7), -}; - -static const struct matrix_keymap_data mop500_keymap_data = { - .keymap = mop500_keymap, - .keymap_size = ARRAY_SIZE(mop500_keymap), -}; -/* - * STMPE1601 - */ -static struct stmpe_keypad_platform_data stmpe1601_keypad_data = { - .debounce_ms = 64, - .scan_count = 8, - .no_autorepeat = true, - .keymap_data = &mop500_keymap_data, -}; - -static struct stmpe_platform_data stmpe1601_data = { - .id = 1, - .blocks = STMPE_BLOCK_KEYPAD, - .irq_trigger = IRQF_TRIGGER_FALLING, - .irq_base = MOP500_STMPE1601_IRQ(0), - .keypad = &stmpe1601_keypad_data, - .autosleep = true, - .autosleep_timeout = 1024, -}; - -static struct i2c_board_info __initdata mop500_i2c0_devices_stuib[] = { - { - I2C_BOARD_INFO("stmpe1601", 0x40), - .irq = NOMADIK_GPIO_TO_IRQ(218), - .platform_data = &stmpe1601_data, - .flags = I2C_CLIENT_WAKE, - }, -}; - -/* - * BU21013 ROHM touchscreen interface on the STUIBs - */ - -#define TOUCH_GPIO_PIN 84 - -#define TOUCH_XMAX 384 -#define TOUCH_YMAX 704 - -#define PRCMU_CLOCK_OCR 0x1CC -#define TSC_EXT_CLOCK_9_6MHZ 0x840000 - -static struct bu21013_platform_device tsc_plat_device = { - .touch_pin = TOUCH_GPIO_PIN, - .touch_x_max = TOUCH_XMAX, - .touch_y_max = TOUCH_YMAX, - .ext_clk = false, - .x_flip = false, - .y_flip = true, -}; - -static struct i2c_board_info __initdata u8500_i2c3_devices_stuib[] = { - { - I2C_BOARD_INFO("bu21013_tp", 0x5C), - .platform_data = &tsc_plat_device, - }, - { - I2C_BOARD_INFO("bu21013_tp", 0x5D), - .platform_data = &tsc_plat_device, - }, -}; - -void __init mop500_stuib_init(void) -{ - if (machine_is_hrefv60()) - tsc_plat_device.cs_pin = HREFV60_TOUCH_RST_GPIO; - else - tsc_plat_device.cs_pin = GPIO_BU21013_CS; - - mop500_uib_i2c_add(0, mop500_i2c0_devices_stuib, - ARRAY_SIZE(mop500_i2c0_devices_stuib)); - - mop500_uib_i2c_add(3, u8500_i2c3_devices_stuib, - ARRAY_SIZE(u8500_i2c3_devices_stuib)); -} diff --git a/arch/arm/mach-ux500/board-mop500-u8500uib.c b/arch/arm/mach-ux500/board-mop500-u8500uib.c deleted file mode 100644 index d397c19..0000000 --- a/arch/arm/mach-ux500/board-mop500-u8500uib.c +++ /dev/null @@ -1,92 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Board data for the U8500 UIB, also known as the New UIB - * License terms: GNU General Public License (GPL), version 2 - */ -#include <linux/gpio.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/i2c.h> -#include <linux/interrupt.h> -#include <linux/mfd/tc3589x.h> -#include <linux/input/matrix_keypad.h> - -#include "irqs.h" - -#include "board-mop500.h" - -static struct i2c_board_info __initdata mop500_i2c3_devices_u8500[] = { - { - I2C_BOARD_INFO("synaptics_rmi4_i2c", 0x4B), - .irq = NOMADIK_GPIO_TO_IRQ(84), - }, -}; - -/* - * TC35893 - */ -static const unsigned int u8500_keymap[] = { - KEY(3, 1, KEY_END), - KEY(4, 1, KEY_POWER), - KEY(6, 4, KEY_VOLUMEDOWN), - KEY(4, 2, KEY_EMAIL), - KEY(3, 3, KEY_RIGHT), - KEY(2, 5, KEY_BACKSPACE), - - KEY(6, 7, KEY_MENU), - KEY(5, 0, KEY_ENTER), - KEY(4, 3, KEY_0), - KEY(3, 4, KEY_DOT), - KEY(5, 2, KEY_UP), - KEY(3, 5, KEY_DOWN), - - KEY(4, 5, KEY_SEND), - KEY(0, 5, KEY_BACK), - KEY(6, 2, KEY_VOLUMEUP), - KEY(1, 3, KEY_SPACE), - KEY(7, 6, KEY_LEFT), - KEY(5, 5, KEY_SEARCH), -}; - -static struct matrix_keymap_data u8500_keymap_data = { - .keymap = u8500_keymap, - .keymap_size = ARRAY_SIZE(u8500_keymap), -}; - -static struct tc3589x_keypad_platform_data tc35893_data = { - .krow = TC_KPD_ROWS, - .kcol = TC_KPD_COLUMNS, - .debounce_period = TC_KPD_DEBOUNCE_PERIOD, - .settle_time = TC_KPD_SETTLE_TIME, - .irqtype = IRQF_TRIGGER_FALLING, - .enable_wakeup = true, - .keymap_data = &u8500_keymap_data, - .no_autorepeat = true, -}; - -static struct tc3589x_platform_data tc3589x_keypad_data = { - .block = TC3589x_BLOCK_KEYPAD, - .keypad = &tc35893_data, - .irq_base = MOP500_EGPIO_IRQ_BASE, -}; - -static struct i2c_board_info __initdata mop500_i2c0_devices_u8500[] = { - { - I2C_BOARD_INFO("tc3589x", 0x44), - .platform_data = &tc3589x_keypad_data, - .irq = NOMADIK_GPIO_TO_IRQ(218), - .flags = I2C_CLIENT_WAKE, - }, -}; - - -void __init mop500_u8500uib_init(void) -{ - mop500_uib_i2c_add(3, mop500_i2c3_devices_u8500, - ARRAY_SIZE(mop500_i2c3_devices_u8500)); - - mop500_uib_i2c_add(0, mop500_i2c0_devices_u8500, - ARRAY_SIZE(mop500_i2c0_devices_u8500)); - -} diff --git a/arch/arm/mach-ux500/board-mop500-uib.c b/arch/arm/mach-ux500/board-mop500-uib.c deleted file mode 100644 index bdaa422..0000000 --- a/arch/arm/mach-ux500/board-mop500-uib.c +++ /dev/null @@ -1,133 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson - * License terms: GNU General Public License (GPL), version 2 - */ - -#define pr_fmt(fmt) "mop500-uib: " fmt - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/i2c.h> - -#include "board-mop500.h" -#include "id.h" - -enum mop500_uib { - STUIB, - U8500UIB, -}; - -struct uib { - const char *name; - const char *option; - void (*init)(void); -}; - -static struct uib __initdata mop500_uibs[] = { - [STUIB] = { - .name = "ST-UIB", - .option = "stuib", - .init = mop500_stuib_init, - }, - [U8500UIB] = { - .name = "U8500-UIB", - .option = "u8500uib", - .init = mop500_u8500uib_init, - }, -}; - -static struct uib *mop500_uib; - -static int __init mop500_uib_setup(char *str) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(mop500_uibs); i++) { - struct uib *uib = &mop500_uibs[i]; - - if (!strcmp(str, uib->option)) { - mop500_uib = uib; - break; - } - } - - if (i == ARRAY_SIZE(mop500_uibs)) - pr_err("invalid uib= option (%s)\n", str); - - return 1; -} -__setup("uib=", mop500_uib_setup); - -/* - * The UIBs are detected after the I2C host controllers are registered, so - * i2c_register_board_info() can't be used. - */ -void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info, - unsigned n) -{ - struct i2c_adapter *adap; - struct i2c_client *client; - int i; - - adap = i2c_get_adapter(busnum); - if (!adap) { - pr_err("failed to get adapter i2c%d\n", busnum); - return; - } - - for (i = 0; i < n; i++) { - client = i2c_new_device(adap, &info[i]); - if (!client) - pr_err("failed to register %s to i2c%d\n", - info[i].type, busnum); - } - - i2c_put_adapter(adap); -} - -static void __init __mop500_uib_init(struct uib *uib, const char *why) -{ - pr_info("%s (%s)\n", uib->name, why); - uib->init(); -} - -/* - * Detect the UIB attached based on the presence or absence of i2c devices. - */ -int __init mop500_uib_init(void) -{ - struct uib *uib = mop500_uib; - struct i2c_adapter *i2c0; - int ret; - - if (!cpu_is_u8500_family()) - return -ENODEV; - - if (uib) { - __mop500_uib_init(uib, "from uib= boot argument"); - return 0; - } - - i2c0 = i2c_get_adapter(0); - if (!i2c0) { - __mop500_uib_init(&mop500_uibs[STUIB], - "fallback, could not get i2c0"); - return -ENODEV; - } - - /* U8500-UIB has the TC35893 at 0x44 on I2C0, the ST-UIB doesn't. */ - ret = i2c_smbus_xfer(i2c0, 0x44, 0, I2C_SMBUS_WRITE, 0, - I2C_SMBUS_QUICK, NULL); - i2c_put_adapter(i2c0); - - if (ret == 0) - uib = &mop500_uibs[U8500UIB]; - else - uib = &mop500_uibs[STUIB]; - - __mop500_uib_init(uib, "detected"); - - return 0; -} diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index ad0806e..514d40b 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -14,27 +14,16 @@ #include <linux/platform_device.h> #include <linux/clk.h> #include <linux/io.h> -#include <linux/i2c.h> -#include <linux/platform_data/i2c-nomadik.h> #include <linux/platform_data/db8500_thermal.h> -#include <linux/gpio.h> #include <linux/amba/bus.h> #include <linux/amba/pl022.h> -#include <linux/amba/serial.h> -#include <linux/spi/spi.h> #include <linux/mfd/abx500/ab8500.h> #include <linux/regulator/ab8500.h> #include <linux/regulator/fixed.h> #include <linux/regulator/driver.h> -#include <linux/regulator/gpio-regulator.h> -#include <linux/mfd/tc3589x.h> #include <linux/mfd/tps6105x.h> -#include <linux/mfd/abx500/ab8500-gpio.h> -#include <linux/mfd/abx500/ab8500-codec.h> #include <linux/platform_data/leds-lp55xx.h> #include <linux/input.h> -#include <linux/smsc911x.h> -#include <linux/gpio_keys.h> #include <linux/delay.h> #include <linux/leds.h> #include <linux/pinctrl/consumer.h> @@ -46,7 +35,6 @@ #include "setup.h" #include "devices.h" #include "irqs.h" -#include <linux/platform_data/crypto-ux500.h> #include "ste-dma40-db8500.h" #include "db8500-regs.h" @@ -54,401 +42,9 @@ #include "board-mop500.h" #include "board-mop500-regulators.h" -static struct gpio_led snowball_led_array[] = { - { - .name = "user_led", - .default_trigger = "heartbeat", - .gpio = 142, - }, -}; - -static struct gpio_led_platform_data snowball_led_data = { - .leds = snowball_led_array, - .num_leds = ARRAY_SIZE(snowball_led_array), -}; - -static struct platform_device snowball_led_dev = { - .name = "leds-gpio", - .dev = { - .platform_data = &snowball_led_data, - }, -}; - -static struct fixed_voltage_config snowball_gpio_en_3v3_data = { - .supply_name = "EN-3V3", - .gpio = SNOWBALL_EN_3V3_ETH_GPIO, - .microvolts = 3300000, - .enable_high = 1, - .init_data = &gpio_en_3v3_regulator, - .startup_delay = 5000, /* 1200us */ -}; - -static struct platform_device snowball_gpio_en_3v3_regulator_dev = { - .name = "reg-fixed-voltage", - .id = 1, - .dev = { - .platform_data = &snowball_gpio_en_3v3_data, - }, -}; - -/* Dynamically populated. */ -static struct gpio sdi0_reg_gpios[] = { - { 0, GPIOF_OUT_INIT_LOW, "mmci_vsel" }, -}; - -static struct gpio_regulator_state sdi0_reg_states[] = { - { .value = 2900000, .gpios = (0 << 0) }, - { .value = 1800000, .gpios = (1 << 0) }, -}; - -static struct gpio_regulator_config sdi0_reg_info = { - .supply_name = "ext-mmc-level-shifter", - .gpios = sdi0_reg_gpios, - .nr_gpios = ARRAY_SIZE(sdi0_reg_gpios), - .states = sdi0_reg_states, - .nr_states = ARRAY_SIZE(sdi0_reg_states), - .type = REGULATOR_VOLTAGE, - .enable_high = 1, - .enabled_at_boot = 0, - .init_data = &sdi0_reg_init_data, - .startup_delay = 100, -}; - -static struct platform_device sdi0_regulator = { - .name = "gpio-regulator", - .id = -1, - .dev = { - .platform_data = &sdi0_reg_info, - }, -}; - -static struct abx500_gpio_platform_data ab8500_gpio_pdata = { - .gpio_base = MOP500_AB8500_PIN_GPIO(1), -}; - -/* ab8500-codec */ -static struct ab8500_codec_platform_data ab8500_codec_pdata = { - .amics = { - .mic1_type = AMIC_TYPE_DIFFERENTIAL, - .mic2_type = AMIC_TYPE_DIFFERENTIAL, - .mic1a_micbias = AMIC_MICBIAS_VAMIC1, - .mic1b_micbias = AMIC_MICBIAS_VAMIC1, - .mic2_micbias = AMIC_MICBIAS_VAMIC2 - }, - .ear_cmv = EAR_CMV_0_95V -}; - -static struct gpio_keys_button snowball_key_array[] = { - { - .gpio = 32, - .type = EV_KEY, - .code = KEY_1, - .desc = "userpb", - .active_low = 1, - .debounce_interval = 50, - .wakeup = 1, - }, - { - .gpio = 151, - .type = EV_KEY, - .code = KEY_2, - .desc = "extkb1", - .active_low = 1, - .debounce_interval = 50, - .wakeup = 1, - }, - { - .gpio = 152, - .type = EV_KEY, - .code = KEY_3, - .desc = "extkb2", - .active_low = 1, - .debounce_interval = 50, - .wakeup = 1, - }, - { - .gpio = 161, - .type = EV_KEY, - .code = KEY_4, - .desc = "extkb3", - .active_low = 1, - .debounce_interval = 50, - .wakeup = 1, - }, - { - .gpio = 162, - .type = EV_KEY, - .code = KEY_5, - .desc = "extkb4", - .active_low = 1, - .debounce_interval = 50, - .wakeup = 1, - }, -}; - -static struct gpio_keys_platform_data snowball_key_data = { - .buttons = snowball_key_array, - .nbuttons = ARRAY_SIZE(snowball_key_array), -}; - -static struct platform_device snowball_key_dev = { - .name = "gpio-keys", - .id = -1, - .dev = { - .platform_data = &snowball_key_data, - } -}; - -static struct smsc911x_platform_config snowball_sbnet_cfg = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH, - .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL, - .flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY, - .shift = 1, -}; - -static struct resource sbnet_res[] = { - { - .name = "smsc911x-memory", - .start = (0x5000 << 16), - .end = (0x5000 << 16) + 0xffff, - .flags = IORESOURCE_MEM, - }, - { - .start = NOMADIK_GPIO_TO_IRQ(140), - .end = NOMADIK_GPIO_TO_IRQ(140), - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, - }, -}; - -static struct platform_device snowball_sbnet_dev = { - .name = "smsc911x", - .num_resources = ARRAY_SIZE(sbnet_res), - .resource = sbnet_res, - .dev = { - .platform_data = &snowball_sbnet_cfg, - }, -}; - struct ab8500_platform_data ab8500_platdata = { .irq_base = MOP500_AB8500_IRQ_BASE, .regulator = &ab8500_regulator_plat_data, - .gpio = &ab8500_gpio_pdata, - .codec = &ab8500_codec_pdata, -}; - -static struct platform_device u8500_cpufreq_cooling_device = { - .name = "db8500-cpufreq-cooling", -}; - -/* - * TPS61052 - */ - -static struct tps6105x_platform_data mop500_tps61052_data = { - .mode = TPS6105X_MODE_VOLTAGE, - .regulator_data = &tps61052_regulator, -}; - -/* - * TC35892 - */ - -static void mop500_tc35892_init(struct tc3589x *tc3589x, unsigned int base) -{ - struct device *parent = NULL; -#if 0 - /* FIXME: Is the sdi actually part of tc3589x? */ - parent = tc3589x->dev; -#endif - mop500_sdi_tc35892_init(parent); -} - -static struct tc3589x_gpio_platform_data mop500_tc35892_gpio_data = { - .gpio_base = MOP500_EGPIO(0), - .setup = mop500_tc35892_init, -}; - -static struct tc3589x_platform_data mop500_tc35892_data = { - .block = TC3589x_BLOCK_GPIO, - .gpio = &mop500_tc35892_gpio_data, - .irq_base = MOP500_EGPIO_IRQ_BASE, -}; - -static struct lp55xx_led_config lp5521_pri_led[] = { - [0] = { - .chan_nr = 0, - .led_current = 0x2f, - .max_current = 0x5f, - }, - [1] = { - .chan_nr = 1, - .led_current = 0x2f, - .max_current = 0x5f, - }, - [2] = { - .chan_nr = 2, - .led_current = 0x2f, - .max_current = 0x5f, - }, -}; - -static struct lp55xx_platform_data __initdata lp5521_pri_data = { - .label = "lp5521_pri", - .led_config = &lp5521_pri_led[0], - .num_channels = 3, - .clock_mode = LP55XX_CLOCK_EXT, -}; - -static struct lp55xx_led_config lp5521_sec_led[] = { - [0] = { - .chan_nr = 0, - .led_current = 0x2f, - .max_current = 0x5f, - }, - [1] = { - .chan_nr = 1, - .led_current = 0x2f, - .max_current = 0x5f, - }, - [2] = { - .chan_nr = 2, - .led_current = 0x2f, - .max_current = 0x5f, - }, -}; - -static struct lp55xx_platform_data __initdata lp5521_sec_data = { - .label = "lp5521_sec", - .led_config = &lp5521_sec_led[0], - .num_channels = 3, - .clock_mode = LP55XX_CLOCK_EXT, -}; - -/* I2C0 devices only available on the first HREF/MOP500 */ -static struct i2c_board_info __initdata mop500_i2c0_devices[] = { - { - I2C_BOARD_INFO("tc3589x", 0x42), - .irq = NOMADIK_GPIO_TO_IRQ(217), - .platform_data = &mop500_tc35892_data, - }, - { - I2C_BOARD_INFO("tps61052", 0x33), - .platform_data = &mop500_tps61052_data, - }, -}; - -static struct i2c_board_info __initdata mop500_i2c2_devices[] = { - { - /* lp5521 LED driver, 1st device */ - I2C_BOARD_INFO("lp5521", 0x33), - .platform_data = &lp5521_pri_data, - }, - { - /* lp5521 LED driver, 2st device */ - I2C_BOARD_INFO("lp5521", 0x34), - .platform_data = &lp5521_sec_data, - }, - { - /* Light sensor Rohm BH1780GLI */ - I2C_BOARD_INFO("bh1780", 0x29), - }, -}; - -static int __init mop500_i2c_board_init(void) -{ - if (machine_is_u8500()) - mop500_uib_i2c_add(0, mop500_i2c0_devices, - ARRAY_SIZE(mop500_i2c0_devices)); - mop500_uib_i2c_add(2, mop500_i2c2_devices, - ARRAY_SIZE(mop500_i2c2_devices)); - return 0; -} -device_initcall(mop500_i2c_board_init); - -static void __init mop500_i2c_init(struct device *parent) -{ - db8500_add_i2c0(parent, NULL); - db8500_add_i2c1(parent, NULL); - db8500_add_i2c2(parent, NULL); - db8500_add_i2c3(parent, NULL); -} - -static struct gpio_keys_button mop500_gpio_keys[] = { - { - .desc = "SFH7741 Proximity Sensor", - .type = EV_SW, - .code = SW_FRONT_PROXIMITY, - .active_low = 0, - .can_disable = 1, - } -}; - -static struct regulator *prox_regulator; -static int mop500_prox_activate(struct device *dev); -static void mop500_prox_deactivate(struct device *dev); - -static struct gpio_keys_platform_data mop500_gpio_keys_data = { - .buttons = mop500_gpio_keys, - .nbuttons = ARRAY_SIZE(mop500_gpio_keys), - .enable = mop500_prox_activate, - .disable = mop500_prox_deactivate, -}; - -static struct platform_device mop500_gpio_keys_device = { - .name = "gpio-keys", - .id = 0, - .dev = { - .platform_data = &mop500_gpio_keys_data, - }, -}; - -static int mop500_prox_activate(struct device *dev) -{ - prox_regulator = regulator_get(&mop500_gpio_keys_device.dev, - "vcc"); - if (IS_ERR(prox_regulator)) { - dev_err(&mop500_gpio_keys_device.dev, - "no regulator\n"); - return PTR_ERR(prox_regulator); - } - - return regulator_enable(prox_regulator); -} - -static void mop500_prox_deactivate(struct device *dev) -{ - regulator_disable(prox_regulator); - regulator_put(prox_regulator); -} - -static struct cryp_platform_data u8500_cryp1_platform_data = { - .mem_to_engine = { - .dir = DMA_MEM_TO_DEV, - .dev_type = DB8500_DMA_DEV48_CAC1, - .mode = STEDMA40_MODE_LOGICAL, - }, - .engine_to_mem = { - .dir = DMA_DEV_TO_MEM, - .dev_type = DB8500_DMA_DEV48_CAC1, - .mode = STEDMA40_MODE_LOGICAL, - } -}; - -static struct stedma40_chan_cfg u8500_hash_dma_cfg_tx = { - .dir = DMA_MEM_TO_DEV, - .dev_type = DB8500_DMA_DEV50_HAC1_TX, - .mode = STEDMA40_MODE_LOGICAL, -}; - -static struct hash_platform_data u8500_hash1_platform_data = { - .mem_to_engine = &u8500_hash_dma_cfg_tx, - .dma_filter = stedma40_filter, -}; - -/* add any platform devices here - TODO */ -static struct platform_device *mop500_platform_devs[] __initdata = { - &mop500_gpio_keys_device, - &sdi0_regulator, }; #ifdef CONFIG_STE_DMA40 @@ -480,236 +76,3 @@ struct pl022_ssp_controller ssp0_plat = { */ .num_chipselect = 5, }; - -static void __init mop500_spi_init(struct device *parent) -{ - db8500_add_ssp0(parent, &ssp0_plat); -} - -#ifdef CONFIG_STE_DMA40 -static struct stedma40_chan_cfg uart0_dma_cfg_rx = { - .mode = STEDMA40_MODE_LOGICAL, - .dir = DMA_DEV_TO_MEM, - .dev_type = DB8500_DMA_DEV13_UART0, -}; - -static struct stedma40_chan_cfg uart0_dma_cfg_tx = { - .mode = STEDMA40_MODE_LOGICAL, - .dir = DMA_MEM_TO_DEV, - .dev_type = DB8500_DMA_DEV13_UART0, -}; - -static struct stedma40_chan_cfg uart1_dma_cfg_rx = { - .mode = STEDMA40_MODE_LOGICAL, - .dir = DMA_DEV_TO_MEM, - .dev_type = DB8500_DMA_DEV12_UART1, -}; - -static struct stedma40_chan_cfg uart1_dma_cfg_tx = { - .mode = STEDMA40_MODE_LOGICAL, - .dir = DMA_MEM_TO_DEV, - .dev_type = DB8500_DMA_DEV12_UART1, -}; - -static struct stedma40_chan_cfg uart2_dma_cfg_rx = { - .mode = STEDMA40_MODE_LOGICAL, - .dir = DMA_DEV_TO_MEM, - .dev_type = DB8500_DMA_DEV11_UART2, -}; - -static struct stedma40_chan_cfg uart2_dma_cfg_tx = { - .mode = STEDMA40_MODE_LOGICAL, - .dir = DMA_MEM_TO_DEV, - .dev_type = DB8500_DMA_DEV11_UART2, -}; -#endif - -struct amba_pl011_data uart0_plat = { -#ifdef CONFIG_STE_DMA40 - .dma_filter = stedma40_filter, - .dma_rx_param = &uart0_dma_cfg_rx, - .dma_tx_param = &uart0_dma_cfg_tx, -#endif -}; - -struct amba_pl011_data uart1_plat = { -#ifdef CONFIG_STE_DMA40 - .dma_filter = stedma40_filter, - .dma_rx_param = &uart1_dma_cfg_rx, - .dma_tx_param = &uart1_dma_cfg_tx, -#endif -}; - -struct amba_pl011_data uart2_plat = { -#ifdef CONFIG_STE_DMA40 - .dma_filter = stedma40_filter, - .dma_rx_param = &uart2_dma_cfg_rx, - .dma_tx_param = &uart2_dma_cfg_tx, -#endif -}; - -static void __init mop500_uart_init(struct device *parent) -{ - db8500_add_uart0(parent, &uart0_plat); - db8500_add_uart1(parent, &uart1_plat); - db8500_add_uart2(parent, &uart2_plat); -} - -static void __init u8500_cryp1_hash1_init(struct device *parent) -{ - db8500_add_cryp1(parent, &u8500_cryp1_platform_data); - db8500_add_hash1(parent, &u8500_hash1_platform_data); -} - -static struct platform_device *snowball_platform_devs[] __initdata = { - &snowball_led_dev, - &snowball_key_dev, - &snowball_sbnet_dev, - &snowball_gpio_en_3v3_regulator_dev, - &u8500_cpufreq_cooling_device, - &sdi0_regulator, -}; - -static void __init mop500_init_machine(void) -{ - struct device *parent = NULL; - int i; - - platform_device_register(&db8500_prcmu_device); - mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR; - - sdi0_reg_info.enable_gpio = GPIO_SDMMC_EN; - sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL; - - mop500_pinmaps_init(); - parent = u8500_init_devices(); - - for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++) - mop500_platform_devs[i]->dev.parent = parent; - - platform_add_devices(mop500_platform_devs, - ARRAY_SIZE(mop500_platform_devs)); - - mop500_i2c_init(parent); - mop500_sdi_init(parent); - mop500_spi_init(parent); - mop500_audio_init(parent); - mop500_uart_init(parent); - u8500_cryp1_hash1_init(parent); - - /* This board has full regulator constraints */ - regulator_has_full_constraints(); -} - - -static void __init snowball_init_machine(void) -{ - struct device *parent = NULL; - int i; - - platform_device_register(&db8500_prcmu_device); - - sdi0_reg_info.enable_gpio = SNOWBALL_SDMMC_EN_GPIO; - sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO; - - snowball_pinmaps_init(); - parent = u8500_init_devices(); - - for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++) - snowball_platform_devs[i]->dev.parent = parent; - - platform_add_devices(snowball_platform_devs, - ARRAY_SIZE(snowball_platform_devs)); - - mop500_i2c_init(parent); - snowball_sdi_init(parent); - mop500_spi_init(parent); - mop500_audio_init(parent); - mop500_uart_init(parent); - - u8500_cryp1_hash1_init(parent); - - /* This board has full regulator constraints */ - regulator_has_full_constraints(); -} - -static void __init hrefv60_init_machine(void) -{ - struct device *parent = NULL; - int i; - - platform_device_register(&db8500_prcmu_device); - /* - * The HREFv60 board removed a GPIO expander and routed - * all these GPIO pins to the internal GPIO controller - * instead. - */ - mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO; - - sdi0_reg_info.enable_gpio = HREFV60_SDMMC_EN_GPIO; - sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO; - - hrefv60_pinmaps_init(); - parent = u8500_init_devices(); - - for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++) - mop500_platform_devs[i]->dev.parent = parent; - - platform_add_devices(mop500_platform_devs, - ARRAY_SIZE(mop500_platform_devs)); - - mop500_i2c_init(parent); - hrefv60_sdi_init(parent); - mop500_spi_init(parent); - mop500_audio_init(parent); - mop500_uart_init(parent); - - /* This board has full regulator constraints */ - regulator_has_full_constraints(); -} - -MACHINE_START(U8500, "ST-Ericsson MOP500 platform") - /* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */ - .atag_offset = 0x100, - .smp = smp_ops(ux500_smp_ops), - .map_io = u8500_map_io, - .init_irq = ux500_init_irq, - /* we re-use nomadik timer here */ - .init_time = ux500_timer_init, - .init_machine = mop500_init_machine, - .init_late = ux500_init_late, - .restart = ux500_restart, -MACHINE_END - -MACHINE_START(U8520, "ST-Ericsson U8520 Platform HREFP520") - .atag_offset = 0x100, - .map_io = u8500_map_io, - .init_irq = ux500_init_irq, - .init_time = ux500_timer_init, - .init_machine = mop500_init_machine, - .init_late = ux500_init_late, - .restart = ux500_restart, -MACHINE_END - -MACHINE_START(HREFV60, "ST-Ericsson U8500 Platform HREFv60+") - .atag_offset = 0x100, - .smp = smp_ops(ux500_smp_ops), - .map_io = u8500_map_io, - .init_irq = ux500_init_irq, - .init_time = ux500_timer_init, - .init_machine = hrefv60_init_machine, - .init_late = ux500_init_late, - .restart = ux500_restart, -MACHINE_END - -MACHINE_START(SNOWBALL, "Calao Systems Snowball platform") - .atag_offset = 0x100, - .smp = smp_ops(ux500_smp_ops), - .map_io = u8500_map_io, - .init_irq = ux500_init_irq, - /* we re-use nomadik timer here */ - .init_time = ux500_timer_init, - .init_machine = snowball_init_machine, - .init_late = NULL, - .restart = ux500_restart, -MACHINE_END diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h index d6fab16..511d6fe 100644 --- a/arch/arm/mach-ux500/board-mop500.h +++ b/arch/arm/mach-ux500/board-mop500.h @@ -79,7 +79,6 @@ #define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */ struct device; -struct i2c_board_info; extern struct mmci_platform_data mop500_sdi0_data; extern struct mmci_platform_data mop500_sdi1_data; extern struct mmci_platform_data mop500_sdi2_data; @@ -88,25 +87,10 @@ extern struct msp_i2s_platform_data msp0_platform_data; extern struct msp_i2s_platform_data msp1_platform_data; extern struct msp_i2s_platform_data msp2_platform_data; extern struct msp_i2s_platform_data msp3_platform_data; -extern struct arm_pmu_platdata db8500_pmu_platdata; -extern struct amba_pl011_data uart0_plat; -extern struct amba_pl011_data uart1_plat; -extern struct amba_pl011_data uart2_plat; extern struct pl022_ssp_controller ssp0_plat; -extern struct stedma40_platform_data dma40_plat_data; -extern void mop500_sdi_init(struct device *parent); -extern void snowball_sdi_init(struct device *parent); -extern void hrefv60_sdi_init(struct device *parent); -extern void mop500_sdi_tc35892_init(struct device *parent); -void __init mop500_u8500uib_init(void); -void __init mop500_stuib_init(void); void __init mop500_pinmaps_init(void); void __init snowball_pinmaps_init(void); void __init hrefv60_pinmaps_init(void); -void mop500_audio_init(struct device *parent); -int __init mop500_uib_init(void); -void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info, - unsigned n); #endif diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c index 301c346..2e85c1e 100644 --- a/arch/arm/mach-ux500/cpu-db8500.c +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -32,7 +32,6 @@ #include "irqs.h" #include "devices-db8500.h" -#include "ste-dma40-db8500.h" #include "db8500-regs.h" #include "board-mop500.h" #include "id.h" @@ -93,14 +92,6 @@ void __init u8500_map_io(void) iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc)); } -static struct resource db8500_pmu_resources[] = { - [0] = { - .start = IRQ_DB8500_PMU, - .end = IRQ_DB8500_PMU, - .flags = IORESOURCE_IRQ, - }, -}; - /* * The PMU IRQ lines of two cores are wired together into a single interrupt. * Bounce the interrupt to the other core if it's not ours. @@ -125,54 +116,6 @@ struct arm_pmu_platdata db8500_pmu_platdata = { .handle_irq = db8500_pmu_handler, }; -static struct platform_device db8500_pmu_device = { - .name = "arm-pmu", - .id = -1, - .num_resources = ARRAY_SIZE(db8500_pmu_resources), - .resource = db8500_pmu_resources, - .dev.platform_data = &db8500_pmu_platdata, -}; - -static struct platform_device *platform_devs[] __initdata = { - &u8500_dma40_device, - &db8500_pmu_device, -}; - -static resource_size_t __initdata db8500_gpio_base[] = { - U8500_GPIOBANK0_BASE, - U8500_GPIOBANK1_BASE, - U8500_GPIOBANK2_BASE, - U8500_GPIOBANK3_BASE, - U8500_GPIOBANK4_BASE, - U8500_GPIOBANK5_BASE, - U8500_GPIOBANK6_BASE, - U8500_GPIOBANK7_BASE, - U8500_GPIOBANK8_BASE, -}; - -static void __init db8500_add_gpios(struct device *parent) -{ - struct nmk_gpio_platform_data pdata = { - .supports_sleepmode = true, - }; - - dbx500_add_gpios(parent, db8500_gpio_base, - ARRAY_SIZE(db8500_gpio_base), - IRQ_DB8500_GPIO0, &pdata); - dbx500_add_pinctrl(parent, "pinctrl-db8500", U8500_PRCMU_BASE); -} - -static int usb_db8500_dma_cfg[] = { - DB8500_DMA_DEV38_USB_OTG_IEP_AND_OEP_1_9, - DB8500_DMA_DEV37_USB_OTG_IEP_AND_OEP_2_10, - DB8500_DMA_DEV36_USB_OTG_IEP_AND_OEP_3_11, - DB8500_DMA_DEV19_USB_OTG_IEP_AND_OEP_4_12, - DB8500_DMA_DEV18_USB_OTG_IEP_AND_OEP_5_13, - DB8500_DMA_DEV17_USB_OTG_IEP_AND_OEP_6_14, - DB8500_DMA_DEV16_USB_OTG_IEP_AND_OEP_7_15, - DB8500_DMA_DEV39_USB_OTG_IEP_AND_OEP_8 -}; - static const char *db8500_read_soc_id(void) { void __iomem *uid = __io_address(U8500_BB_UID_BASE); @@ -192,60 +135,22 @@ static struct device * __init db8500_soc_device_init(void) return ux500_soc_device_init(soc_id); } -/* - * This function is called from the board init - */ -struct device * __init u8500_init_devices(void) -{ - struct device *parent; - int i; - - parent = db8500_soc_device_init(); - - db8500_add_rtc(parent); - db8500_add_gpios(parent); - db8500_add_usb(parent, usb_db8500_dma_cfg, usb_db8500_dma_cfg); - - for (i = 0; i < ARRAY_SIZE(platform_devs); i++) - platform_devs[i]->dev.parent = parent; - - platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs)); - - return parent; -} - #ifdef CONFIG_MACH_UX500_DT static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = { /* Requires call-back bindings. */ OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata), /* Requires DMA bindings. */ - OF_DEV_AUXDATA("arm,pl011", 0x80120000, "uart0", NULL), - OF_DEV_AUXDATA("arm,pl011", 0x80121000, "uart1", NULL), - OF_DEV_AUXDATA("arm,pl011", 0x80007000, "uart2", NULL), - OF_DEV_AUXDATA("arm,pl022", 0x80002000, "ssp0", &ssp0_plat), - OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0", NULL), - OF_DEV_AUXDATA("arm,pl18x", 0x80118000, "sdi1", NULL), - OF_DEV_AUXDATA("arm,pl18x", 0x80005000, "sdi2", NULL), - OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4", NULL), - /* Requires clock name bindings. */ - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e000, "gpio.0", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e080, "gpio.1", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e000, "gpio.2", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e080, "gpio.3", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e100, "gpio.4", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e180, "gpio.5", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e000, "gpio.6", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e080, "gpio.7", NULL), - OF_DEV_AUXDATA("st,nomadik-gpio", 0xa03fe000, "gpio.8", NULL), - OF_DEV_AUXDATA("st,nomadik-i2c", 0x80004000, "nmk-i2c.0", NULL), - OF_DEV_AUXDATA("st,nomadik-i2c", 0x80122000, "nmk-i2c.1", NULL), - OF_DEV_AUXDATA("st,nomadik-i2c", 0x80128000, "nmk-i2c.2", NULL), - OF_DEV_AUXDATA("st,nomadik-i2c", 0x80110000, "nmk-i2c.3", NULL), - OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL), - OF_DEV_AUXDATA("stericsson,db8500-musb", 0xa03e0000, "musb-ux500.0", NULL), + OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000, + "ux500-msp-i2s.0", &msp0_platform_data), + OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000, + "ux500-msp-i2s.1", &msp1_platform_data), + OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80117000, + "ux500-msp-i2s.2", &msp2_platform_data), + OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000, + "ux500-msp-i2s.3", &msp3_platform_data), + /* Requires non-DT:able platform data. */ OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu", &db8500_prcmu_pdata), - OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x.0", NULL), OF_DEV_AUXDATA("stericsson,ux500-cryp", 0xa03cb000, "cryp1", NULL), OF_DEV_AUXDATA("stericsson,ux500-hash", 0xa03c2000, "hash1", NULL), OF_DEV_AUXDATA("stericsson,snd-soc-mop500", 0, "snd-soc-mop500.0", @@ -253,17 +158,6 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = { /* Requires device name bindings. */ OF_DEV_AUXDATA("stericsson,db8500-pinctrl", U8500_PRCMU_BASE, "pinctrl-db8500", NULL), - /* Requires clock name and DMA bindings. */ - OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000, - "ux500-msp-i2s.0", &msp0_platform_data), - OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000, - "ux500-msp-i2s.1", &msp1_platform_data), - OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80117000, - "ux500-msp-i2s.2", &msp2_platform_data), - OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000, - "ux500-msp-i2s.3", &msp3_platform_data), - /* Requires clock name bindings and channel address lookup table. */ - OF_DEV_AUXDATA("stericsson,db8500-dma40", 0x801C0000, "dma40.0", NULL), {}, }; diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c index 5d7eebc..f84d439 100644 --- a/arch/arm/mach-ux500/cpu.c +++ b/arch/arm/mach-ux500/cpu.c @@ -78,9 +78,17 @@ void __init ux500_init_irq(void) if (cpu_is_u8500_family()) { prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1); ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1); - u8500_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE, - U8500_CLKRST3_BASE, U8500_CLKRST5_BASE, - U8500_CLKRST6_BASE); + + if (of_have_populated_dt()) + u8500_of_clk_init(U8500_CLKRST1_BASE, + U8500_CLKRST2_BASE, + U8500_CLKRST3_BASE, + U8500_CLKRST5_BASE, + U8500_CLKRST6_BASE); + else + u8500_clk_init(U8500_CLKRST1_BASE, U8500_CLKRST2_BASE, + U8500_CLKRST3_BASE, U8500_CLKRST5_BASE, + U8500_CLKRST6_BASE); } else if (cpu_is_u9540()) { prcmu_early_init(U8500_PRCMU_BASE, SZ_8K - 1); ux500_pm_init(U8500_PRCMU_BASE, SZ_8K - 1); @@ -96,11 +104,6 @@ void __init ux500_init_irq(void) } } -void __init ux500_init_late(void) -{ - mop500_uib_init(); -} - static const char * __init ux500_get_machine(void) { return kasprintf(GFP_KERNEL, "DB%4x", dbx500_partnumber()); diff --git a/arch/arm/mach-ux500/devices-common.c b/arch/arm/mach-ux500/devices-common.c deleted file mode 100644 index f71b3d7..0000000 --- a/arch/arm/mach-ux500/devices-common.c +++ /dev/null @@ -1,60 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson - * License terms: GNU General Public License (GPL), version 2. - */ - -#include <linux/kernel.h> -#include <linux/dma-mapping.h> -#include <linux/err.h> -#include <linux/irq.h> -#include <linux/slab.h> -#include <linux/platform_device.h> -#include <linux/platform_data/pinctrl-nomadik.h> - -#include "irqs.h" - -#include "devices-common.h" - -static struct platform_device * -dbx500_add_gpio(struct device *parent, int id, resource_size_t addr, int irq, - struct nmk_gpio_platform_data *pdata) -{ - struct resource resources[] = { - { - .start = addr, - .end = addr + 127, - .flags = IORESOURCE_MEM, - }, - { - .start = irq, - .end = irq, - .flags = IORESOURCE_IRQ, - } - }; - - return platform_device_register_resndata( - parent, - "gpio", - id, - resources, - ARRAY_SIZE(resources), - pdata, - sizeof(*pdata)); -} - -void dbx500_add_gpios(struct device *parent, resource_size_t *base, int num, - int irq, struct nmk_gpio_platform_data *pdata) -{ - int first = 0; - int i; - - for (i = 0; i < num; i++, first += 32, irq++) { - pdata->first_gpio = first; - pdata->first_irq = NOMADIK_GPIO_TO_IRQ(first); - pdata->num_gpio = 32; - - dbx500_add_gpio(parent, i, base[i], irq, pdata); - } -} diff --git a/arch/arm/mach-ux500/devices-common.h b/arch/arm/mach-ux500/devices-common.h deleted file mode 100644 index 96fa4ac..0000000 --- a/arch/arm/mach-ux500/devices-common.h +++ /dev/null @@ -1,149 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson - * License terms: GNU General Public License (GPL), version 2. - */ - -#ifndef __DEVICES_COMMON_H -#define __DEVICES_COMMON_H - -#include <linux/platform_device.h> -#include <linux/dma-mapping.h> -#include <linux/sys_soc.h> -#include <linux/amba/bus.h> -#include <linux/platform_data/i2c-nomadik.h> -#include <linux/platform_data/crypto-ux500.h> - -struct spi_master_cntlr; - -static inline struct amba_device * -dbx500_add_msp_spi(struct device *parent, const char *name, - resource_size_t base, int irq, - struct spi_master_cntlr *pdata) -{ - return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, - pdata, 0); -} - -static inline struct amba_device * -dbx500_add_spi(struct device *parent, const char *name, resource_size_t base, - int irq, struct spi_master_cntlr *pdata, - u32 periphid) -{ - return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, - pdata, periphid); -} - -struct mmci_platform_data; - -static inline struct amba_device * -dbx500_add_sdi(struct device *parent, const char *name, resource_size_t base, - int irq, struct mmci_platform_data *pdata, u32 periphid) -{ - return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, - pdata, periphid); -} - -struct amba_pl011_data; - -static inline struct amba_device * -dbx500_add_uart(struct device *parent, const char *name, resource_size_t base, - int irq, struct amba_pl011_data *pdata) -{ - return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, pdata, 0); -} - -struct nmk_i2c_controller; - -static inline struct amba_device * -dbx500_add_i2c(struct device *parent, int id, resource_size_t base, int irq, - struct nmk_i2c_controller *data) -{ - /* Conjure a name similar to what the platform device used to have */ - char name[16]; - - snprintf(name, sizeof(name), "nmk-i2c.%d", id); - return amba_apb_device_add(parent, name, base, SZ_4K, irq, 0, data, 0); -} - -static inline struct amba_device * -dbx500_add_rtc(struct device *parent, resource_size_t base, int irq) -{ - return amba_apb_device_add(parent, "rtc-pl031", base, SZ_4K, irq, - 0, NULL, 0); -} - -struct cryp_platform_data; - -static inline struct platform_device * -dbx500_add_cryp1(struct device *parent, int id, resource_size_t base, int irq, - struct cryp_platform_data *pdata) -{ - struct resource res[] = { - DEFINE_RES_MEM(base, SZ_4K), - DEFINE_RES_IRQ(irq), - }; - - struct platform_device_info pdevinfo = { - .parent = parent, - .name = "cryp1", - .id = id, - .res = res, - .num_res = ARRAY_SIZE(res), - .data = pdata, - .size_data = sizeof(*pdata), - .dma_mask = DMA_BIT_MASK(32), - }; - - return platform_device_register_full(&pdevinfo); -} - -struct hash_platform_data; - -static inline struct platform_device * -dbx500_add_hash1(struct device *parent, int id, resource_size_t base, - struct hash_platform_data *pdata) -{ - struct resource res[] = { - DEFINE_RES_MEM(base, SZ_4K), - }; - - struct platform_device_info pdevinfo = { - .parent = parent, - .name = "hash1", - .id = id, - .res = res, - .num_res = ARRAY_SIZE(res), - .data = pdata, - .size_data = sizeof(*pdata), - .dma_mask = DMA_BIT_MASK(32), - }; - - return platform_device_register_full(&pdevinfo); -} - -struct nmk_gpio_platform_data; - -void dbx500_add_gpios(struct device *parent, resource_size_t *base, int num, - int irq, struct nmk_gpio_platform_data *pdata); - -static inline void -dbx500_add_pinctrl(struct device *parent, const char *name, - resource_size_t base) -{ - struct resource res[] = { - DEFINE_RES_MEM(base, SZ_8K), - }; - struct platform_device_info pdevinfo = { - .parent = parent, - .name = name, - .id = -1, - .res = res, - .num_res = ARRAY_SIZE(res), - }; - - platform_device_register_full(&pdevinfo); -} - -#endif diff --git a/arch/arm/mach-ux500/devices-db8500.c b/arch/arm/mach-ux500/devices-db8500.c index bc31606..c59f89d 100644 --- a/arch/arm/mach-ux500/devices-db8500.c +++ b/arch/arm/mach-ux500/devices-db8500.c @@ -9,10 +9,8 @@ #include <linux/platform_device.h> #include <linux/interrupt.h> #include <linux/io.h> -#include <linux/gpio.h> #include <linux/amba/bus.h> #include <linux/amba/pl022.h> -#include <linux/platform_data/dma-ste-dma40.h> #include <linux/mfd/dbx500-prcmu.h> #include "setup.h" @@ -20,62 +18,6 @@ #include "db8500-regs.h" #include "devices-db8500.h" -#include "ste-dma40-db8500.h" - -static struct resource dma40_resources[] = { - [0] = { - .start = U8500_DMA_BASE, - .end = U8500_DMA_BASE + SZ_4K - 1, - .flags = IORESOURCE_MEM, - .name = "base", - }, - [1] = { - .start = U8500_DMA_LCPA_BASE, - .end = U8500_DMA_LCPA_BASE + 2 * SZ_1K - 1, - .flags = IORESOURCE_MEM, - .name = "lcpa", - }, - [2] = { - .start = IRQ_DB8500_DMA, - .end = IRQ_DB8500_DMA, - .flags = IORESOURCE_IRQ, - } -}; - -struct stedma40_platform_data dma40_plat_data = { - .disabled_channels = {-1}, -}; - -struct platform_device u8500_dma40_device = { - .dev = { - .platform_data = &dma40_plat_data, - .coherent_dma_mask = DMA_BIT_MASK(32), - }, - .name = "dma40", - .id = 0, - .num_resources = ARRAY_SIZE(dma40_resources), - .resource = dma40_resources -}; - -struct resource keypad_resources[] = { - [0] = { - .start = U8500_SKE_BASE, - .end = U8500_SKE_BASE + SZ_4K - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_DB8500_KB, - .end = IRQ_DB8500_KB, - .flags = IORESOURCE_IRQ, - }, -}; - -struct platform_device u8500_ske_keypad_device = { - .name = "nmk-ske-keypad", - .id = -1, - .num_resources = ARRAY_SIZE(keypad_resources), - .resource = keypad_resources, -}; struct prcmu_pdata db8500_prcmu_pdata = { .ab_platdata = &ab8500_platdata, @@ -84,39 +26,3 @@ struct prcmu_pdata db8500_prcmu_pdata = { .version_offset = DB8500_PRCMU_FW_VERSION_OFFSET, .legacy_offset = DB8500_PRCMU_LEGACY_OFFSET, }; - -static struct resource db8500_prcmu_res[] = { - { - .name = "prcmu", - .start = U8500_PRCMU_BASE, - .end = U8500_PRCMU_BASE + SZ_8K - 1, - .flags = IORESOURCE_MEM, - }, - { - .name = "prcmu-tcdm", - .start = U8500_PRCMU_TCDM_BASE, - .end = U8500_PRCMU_TCDM_BASE + SZ_4K - 1, - .flags = IORESOURCE_MEM, - }, - { - .name = "irq", - .start = IRQ_DB8500_PRCMU1, - .end = IRQ_DB8500_PRCMU1, - .flags = IORESOURCE_IRQ, - }, - { - .name = "prcmu-tcpm", - .start = U8500_PRCMU_TCPM_BASE, - .end = U8500_PRCMU_TCPM_BASE + SZ_32K - 1, - .flags = IORESOURCE_MEM, - }, -}; - -struct platform_device db8500_prcmu_device = { - .name = "db8500-prcmu", - .resource = db8500_prcmu_res, - .num_resources = ARRAY_SIZE(db8500_prcmu_res), - .dev = { - .platform_data = &db8500_prcmu_pdata, - }, -}; diff --git a/arch/arm/mach-ux500/devices-db8500.h b/arch/arm/mach-ux500/devices-db8500.h index 3219983..b8ffc99 100644 --- a/arch/arm/mach-ux500/devices-db8500.h +++ b/arch/arm/mach-ux500/devices-db8500.h @@ -8,122 +8,12 @@ #ifndef __DEVICES_DB8500_H #define __DEVICES_DB8500_H -#include <linux/platform_data/usb-musb-ux500.h> #include "irqs.h" #include "db8500-regs.h" -#include "devices-common.h" -struct ske_keypad_platform_data; -struct pl022_ssp_controller; struct platform_device; extern struct ab8500_platform_data ab8500_platdata; extern struct prcmu_pdata db8500_prcmu_pdata; -extern struct platform_device db8500_prcmu_device; -static inline struct platform_device * -db8500_add_ske_keypad(struct device *parent, - struct ske_keypad_platform_data *pdata, - size_t size) -{ - struct resource resources[] = { - DEFINE_RES_MEM(U8500_SKE_BASE, SZ_4K), - DEFINE_RES_IRQ(IRQ_DB8500_KB), - }; - - return platform_device_register_resndata(parent, "nmk-ske-keypad", -1, - resources, 2, pdata, size); -} - -static inline struct amba_device * -db8500_add_ssp(struct device *parent, const char *name, resource_size_t base, - int irq, struct pl022_ssp_controller *pdata) -{ - return amba_ahb_device_add(parent, name, base, SZ_4K, irq, 0, pdata, 0); -} - -#define db8500_add_i2c0(parent, pdata) \ - dbx500_add_i2c(parent, 0, U8500_I2C0_BASE, IRQ_DB8500_I2C0, pdata) -#define db8500_add_i2c1(parent, pdata) \ - dbx500_add_i2c(parent, 1, U8500_I2C1_BASE, IRQ_DB8500_I2C1, pdata) -#define db8500_add_i2c2(parent, pdata) \ - dbx500_add_i2c(parent, 2, U8500_I2C2_BASE, IRQ_DB8500_I2C2, pdata) -#define db8500_add_i2c3(parent, pdata) \ - dbx500_add_i2c(parent, 3, U8500_I2C3_BASE, IRQ_DB8500_I2C3, pdata) -#define db8500_add_i2c4(parent, pdata) \ - dbx500_add_i2c(parent, 4, U8500_I2C4_BASE, IRQ_DB8500_I2C4, pdata) - -#define db8500_add_msp0_spi(parent, pdata) \ - dbx500_add_msp_spi(parent, "msp0", U8500_MSP0_BASE, \ - IRQ_DB8500_MSP0, pdata) -#define db8500_add_msp1_spi(parent, pdata) \ - dbx500_add_msp_spi(parent, "msp1", U8500_MSP1_BASE, \ - IRQ_DB8500_MSP1, pdata) -#define db8500_add_msp2_spi(parent, pdata) \ - dbx500_add_msp_spi(parent, "msp2", U8500_MSP2_BASE, \ - IRQ_DB8500_MSP2, pdata) -#define db8500_add_msp3_spi(parent, pdata) \ - dbx500_add_msp_spi(parent, "msp3", U8500_MSP3_BASE, \ - IRQ_DB8500_MSP1, pdata) - -#define db8500_add_rtc(parent) \ - dbx500_add_rtc(parent, U8500_RTC_BASE, IRQ_DB8500_RTC); - -#define db8500_add_usb(parent, rx_cfg, tx_cfg) \ - ux500_add_usb(parent, U8500_USBOTG_BASE, \ - IRQ_DB8500_USBOTG, rx_cfg, tx_cfg) - -#define db8500_add_sdi0(parent, pdata, pid) \ - dbx500_add_sdi(parent, "sdi0", U8500_SDI0_BASE, \ - IRQ_DB8500_SDMMC0, pdata, pid) -#define db8500_add_sdi1(parent, pdata, pid) \ - dbx500_add_sdi(parent, "sdi1", U8500_SDI1_BASE, \ - IRQ_DB8500_SDMMC1, pdata, pid) -#define db8500_add_sdi2(parent, pdata, pid) \ - dbx500_add_sdi(parent, "sdi2", U8500_SDI2_BASE, \ - IRQ_DB8500_SDMMC2, pdata, pid) -#define db8500_add_sdi3(parent, pdata, pid) \ - dbx500_add_sdi(parent, "sdi3", U8500_SDI3_BASE, \ - IRQ_DB8500_SDMMC3, pdata, pid) -#define db8500_add_sdi4(parent, pdata, pid) \ - dbx500_add_sdi(parent, "sdi4", U8500_SDI4_BASE, \ - IRQ_DB8500_SDMMC4, pdata, pid) -#define db8500_add_sdi5(parent, pdata, pid) \ - dbx500_add_sdi(parent, "sdi5", U8500_SDI5_BASE, \ - IRQ_DB8500_SDMMC5, pdata, pid) - -#define db8500_add_ssp0(parent, pdata) \ - db8500_add_ssp(parent, "ssp0", U8500_SSP0_BASE, \ - IRQ_DB8500_SSP0, pdata) -#define db8500_add_ssp1(parent, pdata) \ - db8500_add_ssp(parent, "ssp1", U8500_SSP1_BASE, \ - IRQ_DB8500_SSP1, pdata) - -#define db8500_add_spi0(parent, pdata) \ - dbx500_add_spi(parent, "spi0", U8500_SPI0_BASE, \ - IRQ_DB8500_SPI0, pdata, 0) -#define db8500_add_spi1(parent, pdata) \ - dbx500_add_spi(parent, "spi1", U8500_SPI1_BASE, \ - IRQ_DB8500_SPI1, pdata, 0) -#define db8500_add_spi2(parent, pdata) \ - dbx500_add_spi(parent, "spi2", U8500_SPI2_BASE, \ - IRQ_DB8500_SPI2, pdata, 0) -#define db8500_add_spi3(parent, pdata) \ - dbx500_add_spi(parent, "spi3", U8500_SPI3_BASE, \ - IRQ_DB8500_SPI3, pdata, 0) - -#define db8500_add_uart0(parent, pdata) \ - dbx500_add_uart(parent, "uart0", U8500_UART0_BASE, \ - IRQ_DB8500_UART0, pdata) -#define db8500_add_uart1(parent, pdata) \ - dbx500_add_uart(parent, "uart1", U8500_UART1_BASE, \ - IRQ_DB8500_UART1, pdata) -#define db8500_add_uart2(parent, pdata) \ - dbx500_add_uart(parent, "uart2", U8500_UART2_BASE, \ - IRQ_DB8500_UART2, pdata) - -#define db8500_add_cryp1(parent, pdata) \ - dbx500_add_cryp1(parent, -1, U8500_CRYP1_BASE, IRQ_DB8500_CRYP1, pdata) -#define db8500_add_hash1(parent, pdata) \ - dbx500_add_hash1(parent, -1, U8500_HASH1_BASE, pdata) #endif diff --git a/arch/arm/mach-ux500/devices.h b/arch/arm/mach-ux500/devices.h index cbc6f1e..5bca7c6 100644 --- a/arch/arm/mach-ux500/devices.h +++ b/arch/arm/mach-ux500/devices.h @@ -10,14 +10,6 @@ struct platform_device; struct amba_device; -extern struct platform_device u8500_gpio_devs[]; - extern struct amba_device ux500_pl031_device; -extern struct platform_device ux500_hash1_device; -extern struct platform_device ux500_cryp1_device; - -extern struct platform_device u8500_dma40_device; -extern struct platform_device ux500_ske_keypad_device; - #endif diff --git a/arch/arm/mach-ux500/setup.h b/arch/arm/mach-ux500/setup.h index 656324a..bdb3564 100644 --- a/arch/arm/mach-ux500/setup.h +++ b/arch/arm/mach-ux500/setup.h @@ -24,7 +24,6 @@ extern void __init u8500_map_io(void); extern struct device * __init u8500_init_devices(void); extern void __init ux500_init_irq(void); -extern void __init ux500_init_late(void); extern struct device *ux500_soc_device_init(const char *soc_id); diff --git a/arch/arm/mach-ux500/timer.c b/arch/arm/mach-ux500/timer.c index b6bd0ef..05a4ff7 100644 --- a/arch/arm/mach-ux500/timer.c +++ b/arch/arm/mach-ux500/timer.c @@ -97,8 +97,8 @@ dt_fail: * sched_clock with higher rating then MTU since is always-on. * */ - - nmdk_timer_init(mtu_timer_base, IRQ_MTU0); + if (!of_have_populated_dt()) + nmdk_timer_init(mtu_timer_base, IRQ_MTU0); clksrc_dbx500_prcmu_init(prcmu_timer_base); ux500_twd_init(); } diff --git a/arch/arm/mach-ux500/usb.c b/arch/arm/mach-ux500/usb.c deleted file mode 100644 index b7bd8d3..0000000 --- a/arch/arm/mach-ux500/usb.c +++ /dev/null @@ -1,135 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2011 - * - * Author: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> - * License terms: GNU General Public License (GPL) version 2 - */ -#include <linux/platform_device.h> -#include <linux/usb/musb.h> -#include <linux/dma-mapping.h> -#include <linux/platform_data/usb-musb-ux500.h> -#include <linux/platform_data/dma-ste-dma40.h> - -#include "db8500-regs.h" - -#define MUSB_DMA40_RX_CH { \ - .mode = STEDMA40_MODE_LOGICAL, \ - .dir = DMA_DEV_TO_MEM, \ - } - -#define MUSB_DMA40_TX_CH { \ - .mode = STEDMA40_MODE_LOGICAL, \ - .dir = DMA_MEM_TO_DEV, \ - } - -static struct stedma40_chan_cfg musb_dma_rx_ch[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] - = { - MUSB_DMA40_RX_CH, - MUSB_DMA40_RX_CH, - MUSB_DMA40_RX_CH, - MUSB_DMA40_RX_CH, - MUSB_DMA40_RX_CH, - MUSB_DMA40_RX_CH, - MUSB_DMA40_RX_CH, - MUSB_DMA40_RX_CH -}; - -static struct stedma40_chan_cfg musb_dma_tx_ch[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] - = { - MUSB_DMA40_TX_CH, - MUSB_DMA40_TX_CH, - MUSB_DMA40_TX_CH, - MUSB_DMA40_TX_CH, - MUSB_DMA40_TX_CH, - MUSB_DMA40_TX_CH, - MUSB_DMA40_TX_CH, - MUSB_DMA40_TX_CH, -}; - -static void *ux500_dma_rx_param_array[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] = { - &musb_dma_rx_ch[0], - &musb_dma_rx_ch[1], - &musb_dma_rx_ch[2], - &musb_dma_rx_ch[3], - &musb_dma_rx_ch[4], - &musb_dma_rx_ch[5], - &musb_dma_rx_ch[6], - &musb_dma_rx_ch[7] -}; - -static void *ux500_dma_tx_param_array[UX500_MUSB_DMA_NUM_RX_TX_CHANNELS] = { - &musb_dma_tx_ch[0], - &musb_dma_tx_ch[1], - &musb_dma_tx_ch[2], - &musb_dma_tx_ch[3], - &musb_dma_tx_ch[4], - &musb_dma_tx_ch[5], - &musb_dma_tx_ch[6], - &musb_dma_tx_ch[7] -}; - -static struct ux500_musb_board_data musb_board_data = { - .dma_rx_param_array = ux500_dma_rx_param_array, - .dma_tx_param_array = ux500_dma_tx_param_array, - .dma_filter = stedma40_filter, -}; - -static struct musb_hdrc_platform_data musb_platform_data = { - .mode = MUSB_OTG, - .board_data = &musb_board_data, -}; - -static struct resource usb_resources[] = { - [0] = { - .name = "usb-mem", - .flags = IORESOURCE_MEM, - }, - - [1] = { - .name = "mc", /* hard-coded in musb */ - .flags = IORESOURCE_IRQ, - }, -}; - -struct platform_device ux500_musb_device = { - .name = "musb-ux500", - .id = 0, - .dev = { - .platform_data = &musb_platform_data, - .coherent_dma_mask = DMA_BIT_MASK(32), - }, - .num_resources = ARRAY_SIZE(usb_resources), - .resource = usb_resources, -}; - -static inline void ux500_usb_dma_update_rx_ch_config(int *dev_type) -{ - u32 idx; - - for (idx = 0; idx < UX500_MUSB_DMA_NUM_RX_TX_CHANNELS; idx++) - musb_dma_rx_ch[idx].dev_type = dev_type[idx]; -} - -static inline void ux500_usb_dma_update_tx_ch_config(int *dev_type) -{ - u32 idx; - - for (idx = 0; idx < UX500_MUSB_DMA_NUM_RX_TX_CHANNELS; idx++) - musb_dma_tx_ch[idx].dev_type = dev_type[idx]; -} - -void ux500_add_usb(struct device *parent, resource_size_t base, int irq, - int *dma_rx_cfg, int *dma_tx_cfg) -{ - ux500_musb_device.resource[0].start = base; - ux500_musb_device.resource[0].end = base + SZ_64K - 1; - ux500_musb_device.resource[1].start = irq; - ux500_musb_device.resource[1].end = irq; - - ux500_usb_dma_update_rx_ch_config(dma_rx_cfg); - ux500_usb_dma_update_tx_ch_config(dma_tx_cfg); - - ux500_musb_device.dev.parent = parent; - - platform_device_register(&ux500_musb_device); -} diff --git a/arch/arm/plat-samsung/init.c b/arch/arm/plat-samsung/init.c index 50a3ea0..aa9511b 100644 --- a/arch/arm/plat-samsung/init.c +++ b/arch/arm/plat-samsung/init.c @@ -11,12 +11,18 @@ * published by the Free Software Foundation. */ +/* + * NOTE: Code in this file is not used on S3C64xx when booting with + * Device Tree support. + */ + #include <linux/init.h> #include <linux/module.h> #include <linux/interrupt.h> #include <linux/ioport.h> #include <linux/serial_core.h> #include <linux/platform_device.h> +#include <linux/of.h> #include <mach/hardware.h> @@ -148,8 +154,12 @@ static int __init s3c_arch_init(void) // do the correct init for cpu - if (cpu == NULL) + if (cpu == NULL) { + /* Not needed when booting with device tree. */ + if (of_have_populated_dt()) + return 0; panic("s3c_arch_init: NULL cpu\n"); + } ret = (cpu->init)(); if (ret != 0) diff --git a/drivers/clk/ux500/Makefile b/drivers/clk/ux500/Makefile index c6a806e..521483f 100644 --- a/drivers/clk/ux500/Makefile +++ b/drivers/clk/ux500/Makefile @@ -8,6 +8,7 @@ obj-y += clk-prcmu.o obj-y += clk-sysctrl.o # Clock definitions +obj-y += u8500_of_clk.o obj-y += u8500_clk.o obj-y += u9540_clk.o obj-y += u8540_clk.o diff --git a/drivers/clk/ux500/u8500_of_clk.c b/drivers/clk/ux500/u8500_of_clk.c new file mode 100644 index 0000000..cdeff29 --- /dev/null +++ b/drivers/clk/ux500/u8500_of_clk.c @@ -0,0 +1,559 @@ +/* + * Clock definitions for u8500 platform. + * + * Copyright (C) 2012 ST-Ericsson SA + * Author: Ulf Hansson <ulf.hansson@linaro.org> + * + * License terms: GNU General Public License (GPL) version 2 + */ + +#include <linux/of.h> +#include <linux/clk.h> +#include <linux/clkdev.h> +#include <linux/clk-provider.h> +#include <linux/mfd/dbx500-prcmu.h> +#include <linux/platform_data/clk-ux500.h> +#include "clk.h" + +#define PRCC_NUM_PERIPH_CLUSTERS 6 +#define PRCC_PERIPHS_PER_CLUSTER 32 + +static struct clk *prcmu_clk[PRCMU_NUM_CLKS]; +static struct clk *prcc_pclk[(PRCC_NUM_PERIPH_CLUSTERS + 1) * PRCC_PERIPHS_PER_CLUSTER]; +static struct clk *prcc_kclk[(PRCC_NUM_PERIPH_CLUSTERS + 1) * PRCC_PERIPHS_PER_CLUSTER]; + +#define PRCC_SHOW(clk, base, bit) \ + clk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit] +#define PRCC_PCLK_STORE(clk, base, bit) \ + prcc_pclk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit] = clk +#define PRCC_KCLK_STORE(clk, base, bit) \ + prcc_kclk[(base * PRCC_PERIPHS_PER_CLUSTER) + bit] = clk + +struct clk *ux500_twocell_get(struct of_phandle_args *clkspec, void *data) +{ + struct clk **clk_data = data; + unsigned int base, bit; + + if (clkspec->args_count != 2) + return ERR_PTR(-EINVAL); + + base = clkspec->args[0]; + bit = clkspec->args[1]; + + if (base != 1 && base != 2 && base != 3 && base != 5 && base != 6) { + pr_err("%s: invalid PRCC base %d\n", __func__, base); + return ERR_PTR(-EINVAL); + } + + return PRCC_SHOW(clk_data, base, bit); +} + +static const struct of_device_id u8500_clk_of_match[] = { + { .compatible = "stericsson,u8500-clks", }, + { }, +}; + +void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, + u32 clkrst5_base, u32 clkrst6_base) +{ + struct prcmu_fw_version *fw_version; + struct device_node *np = NULL; + struct device_node *child = NULL; + const char *sgaclk_parent = NULL; + struct clk *clk, *rtc_clk, *twd_clk; + + if (of_have_populated_dt()) + np = of_find_matching_node(NULL, u8500_clk_of_match); + if (!np) { + pr_err("Either DT or U8500 Clock node not found\n"); + return; + } + + /* Clock sources */ + clk = clk_reg_prcmu_gate("soc0_pll", NULL, PRCMU_PLLSOC0, + CLK_IS_ROOT|CLK_IGNORE_UNUSED); + prcmu_clk[PRCMU_PLLSOC0] = clk; + + clk = clk_reg_prcmu_gate("soc1_pll", NULL, PRCMU_PLLSOC1, + CLK_IS_ROOT|CLK_IGNORE_UNUSED); + prcmu_clk[PRCMU_PLLSOC1] = clk; + + clk = clk_reg_prcmu_gate("ddr_pll", NULL, PRCMU_PLLDDR, + CLK_IS_ROOT|CLK_IGNORE_UNUSED); + prcmu_clk[PRCMU_PLLDDR] = clk; + + /* FIXME: Add sys, ulp and int clocks here. */ + + rtc_clk = clk_register_fixed_rate(NULL, "rtc32k", "NULL", + CLK_IS_ROOT|CLK_IGNORE_UNUSED, + 32768); + + /* PRCMU clocks */ + fw_version = prcmu_get_fw_version(); + if (fw_version != NULL) { + switch (fw_version->project) { + case PRCMU_FW_PROJECT_U8500_C2: + case PRCMU_FW_PROJECT_U8520: + case PRCMU_FW_PROJECT_U8420: + sgaclk_parent = "soc0_pll"; + break; + default: + break; + } + } + + if (sgaclk_parent) + clk = clk_reg_prcmu_gate("sgclk", sgaclk_parent, + PRCMU_SGACLK, 0); + else + clk = clk_reg_prcmu_gate("sgclk", NULL, + PRCMU_SGACLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_SGACLK] = clk; + + clk = clk_reg_prcmu_gate("uartclk", NULL, PRCMU_UARTCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_UARTCLK] = clk; + + clk = clk_reg_prcmu_gate("msp02clk", NULL, PRCMU_MSP02CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_MSP02CLK] = clk; + + clk = clk_reg_prcmu_gate("msp1clk", NULL, PRCMU_MSP1CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_MSP1CLK] = clk; + + clk = clk_reg_prcmu_gate("i2cclk", NULL, PRCMU_I2CCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_I2CCLK] = clk; + + clk = clk_reg_prcmu_gate("slimclk", NULL, PRCMU_SLIMCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_SLIMCLK] = clk; + + clk = clk_reg_prcmu_gate("per1clk", NULL, PRCMU_PER1CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_PER1CLK] = clk; + + clk = clk_reg_prcmu_gate("per2clk", NULL, PRCMU_PER2CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_PER2CLK] = clk; + + clk = clk_reg_prcmu_gate("per3clk", NULL, PRCMU_PER3CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_PER3CLK] = clk; + + clk = clk_reg_prcmu_gate("per5clk", NULL, PRCMU_PER5CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_PER5CLK] = clk; + + clk = clk_reg_prcmu_gate("per6clk", NULL, PRCMU_PER6CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_PER6CLK] = clk; + + clk = clk_reg_prcmu_gate("per7clk", NULL, PRCMU_PER7CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_PER7CLK] = clk; + + clk = clk_reg_prcmu_scalable("lcdclk", NULL, PRCMU_LCDCLK, 0, + CLK_IS_ROOT|CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_LCDCLK] = clk; + + clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BMLCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_BMLCLK] = clk; + + clk = clk_reg_prcmu_scalable("hsitxclk", NULL, PRCMU_HSITXCLK, 0, + CLK_IS_ROOT|CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_HSITXCLK] = clk; + + clk = clk_reg_prcmu_scalable("hsirxclk", NULL, PRCMU_HSIRXCLK, 0, + CLK_IS_ROOT|CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_HSIRXCLK] = clk; + + clk = clk_reg_prcmu_scalable("hdmiclk", NULL, PRCMU_HDMICLK, 0, + CLK_IS_ROOT|CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_HDMICLK] = clk; + + clk = clk_reg_prcmu_gate("apeatclk", NULL, PRCMU_APEATCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_APEATCLK] = clk; + + clk = clk_reg_prcmu_gate("apetraceclk", NULL, PRCMU_APETRACECLK, + CLK_IS_ROOT); + prcmu_clk[PRCMU_APETRACECLK] = clk; + + clk = clk_reg_prcmu_gate("mcdeclk", NULL, PRCMU_MCDECLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_MCDECLK] = clk; + + clk = clk_reg_prcmu_opp_gate("ipi2cclk", NULL, PRCMU_IPI2CCLK, + CLK_IS_ROOT); + prcmu_clk[PRCMU_IPI2CCLK] = clk; + + clk = clk_reg_prcmu_gate("dsialtclk", NULL, PRCMU_DSIALTCLK, + CLK_IS_ROOT); + prcmu_clk[PRCMU_DSIALTCLK] = clk; + + clk = clk_reg_prcmu_gate("dmaclk", NULL, PRCMU_DMACLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_DMACLK] = clk; + + clk = clk_reg_prcmu_gate("b2r2clk", NULL, PRCMU_B2R2CLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_B2R2CLK] = clk; + + clk = clk_reg_prcmu_scalable("tvclk", NULL, PRCMU_TVCLK, 0, + CLK_IS_ROOT|CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_TVCLK] = clk; + + clk = clk_reg_prcmu_gate("sspclk", NULL, PRCMU_SSPCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_SSPCLK] = clk; + + clk = clk_reg_prcmu_gate("rngclk", NULL, PRCMU_RNGCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_RNGCLK] = clk; + + clk = clk_reg_prcmu_gate("uiccclk", NULL, PRCMU_UICCCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_UICCCLK] = clk; + + clk = clk_reg_prcmu_gate("timclk", NULL, PRCMU_TIMCLK, CLK_IS_ROOT); + prcmu_clk[PRCMU_TIMCLK] = clk; + + clk = clk_reg_prcmu_opp_volt_scalable("sdmmcclk", NULL, PRCMU_SDMMCCLK, + 100000000, + CLK_IS_ROOT|CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_SDMMCCLK] = clk; + + clk = clk_reg_prcmu_scalable("dsi_pll", "hdmiclk", + PRCMU_PLLDSI, 0, CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_PLLDSI] = clk; + + clk = clk_reg_prcmu_scalable("dsi0clk", "dsi_pll", + PRCMU_DSI0CLK, 0, CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_DSI0CLK] = clk; + + clk = clk_reg_prcmu_scalable("dsi1clk", "dsi_pll", + PRCMU_DSI1CLK, 0, CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_DSI1CLK] = clk; + + clk = clk_reg_prcmu_scalable("dsi0escclk", "tvclk", + PRCMU_DSI0ESCCLK, 0, CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_DSI0ESCCLK] = clk; + + clk = clk_reg_prcmu_scalable("dsi1escclk", "tvclk", + PRCMU_DSI1ESCCLK, 0, CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_DSI1ESCCLK] = clk; + + clk = clk_reg_prcmu_scalable("dsi2escclk", "tvclk", + PRCMU_DSI2ESCCLK, 0, CLK_SET_RATE_GATE); + prcmu_clk[PRCMU_DSI2ESCCLK] = clk; + + clk = clk_reg_prcmu_scalable_rate("armss", NULL, + PRCMU_ARMSS, 0, CLK_IS_ROOT|CLK_IGNORE_UNUSED); + prcmu_clk[PRCMU_ARMSS] = clk; + + twd_clk = clk_register_fixed_factor(NULL, "smp_twd", "armss", + CLK_IGNORE_UNUSED, 1, 2); + + /* + * FIXME: Add special handled PRCMU clocks here: + * 1. clkout0yuv, use PRCMU as parent + need regulator + pinctrl. + * 2. ab9540_clkout1yuv, see clkout0yuv + */ + + /* PRCC P-clocks */ + clk = clk_reg_prcc_pclk("p1_pclk0", "per1clk", clkrst1_base, + BIT(0), 0); + PRCC_PCLK_STORE(clk, 1, 0); + + clk = clk_reg_prcc_pclk("p1_pclk1", "per1clk", clkrst1_base, + BIT(1), 0); + PRCC_PCLK_STORE(clk, 1, 1); + + clk = clk_reg_prcc_pclk("p1_pclk2", "per1clk", clkrst1_base, + BIT(2), 0); + PRCC_PCLK_STORE(clk, 1, 2); + + clk = clk_reg_prcc_pclk("p1_pclk3", "per1clk", clkrst1_base, + BIT(3), 0); + PRCC_PCLK_STORE(clk, 1, 3); + + clk = clk_reg_prcc_pclk("p1_pclk4", "per1clk", clkrst1_base, + BIT(4), 0); + PRCC_PCLK_STORE(clk, 1, 4); + + clk = clk_reg_prcc_pclk("p1_pclk5", "per1clk", clkrst1_base, + BIT(5), 0); + PRCC_PCLK_STORE(clk, 1, 5); + + clk = clk_reg_prcc_pclk("p1_pclk6", "per1clk", clkrst1_base, + BIT(6), 0); + PRCC_PCLK_STORE(clk, 1, 6); + + clk = clk_reg_prcc_pclk("p1_pclk7", "per1clk", clkrst1_base, + BIT(7), 0); + PRCC_PCLK_STORE(clk, 1, 7); + + clk = clk_reg_prcc_pclk("p1_pclk8", "per1clk", clkrst1_base, + BIT(8), 0); + PRCC_PCLK_STORE(clk, 1, 8); + + clk = clk_reg_prcc_pclk("p1_pclk9", "per1clk", clkrst1_base, + BIT(9), 0); + PRCC_PCLK_STORE(clk, 1, 9); + + clk = clk_reg_prcc_pclk("p1_pclk10", "per1clk", clkrst1_base, + BIT(10), 0); + PRCC_PCLK_STORE(clk, 1, 10); + + clk = clk_reg_prcc_pclk("p1_pclk11", "per1clk", clkrst1_base, + BIT(11), 0); + PRCC_PCLK_STORE(clk, 1, 11); + + clk = clk_reg_prcc_pclk("p2_pclk0", "per2clk", clkrst2_base, + BIT(0), 0); + PRCC_PCLK_STORE(clk, 2, 0); + + clk = clk_reg_prcc_pclk("p2_pclk1", "per2clk", clkrst2_base, + BIT(1), 0); + PRCC_PCLK_STORE(clk, 2, 1); + + clk = clk_reg_prcc_pclk("p2_pclk2", "per2clk", clkrst2_base, + BIT(2), 0); + PRCC_PCLK_STORE(clk, 2, 2); + + clk = clk_reg_prcc_pclk("p2_pclk3", "per2clk", clkrst2_base, + BIT(3), 0); + PRCC_PCLK_STORE(clk, 2, 3); + + clk = clk_reg_prcc_pclk("p2_pclk4", "per2clk", clkrst2_base, + BIT(4), 0); + PRCC_PCLK_STORE(clk, 2, 4); + + clk = clk_reg_prcc_pclk("p2_pclk5", "per2clk", clkrst2_base, + BIT(5), 0); + PRCC_PCLK_STORE(clk, 2, 5); + + clk = clk_reg_prcc_pclk("p2_pclk6", "per2clk", clkrst2_base, + BIT(6), 0); + PRCC_PCLK_STORE(clk, 2, 6); + + clk = clk_reg_prcc_pclk("p2_pclk7", "per2clk", clkrst2_base, + BIT(7), 0); + PRCC_PCLK_STORE(clk, 2, 7); + + clk = clk_reg_prcc_pclk("p2_pclk8", "per2clk", clkrst2_base, + BIT(8), 0); + PRCC_PCLK_STORE(clk, 2, 8); + + clk = clk_reg_prcc_pclk("p2_pclk9", "per2clk", clkrst2_base, + BIT(9), 0); + PRCC_PCLK_STORE(clk, 2, 9); + + clk = clk_reg_prcc_pclk("p2_pclk10", "per2clk", clkrst2_base, + BIT(10), 0); + PRCC_PCLK_STORE(clk, 2, 10); + + clk = clk_reg_prcc_pclk("p2_pclk11", "per2clk", clkrst2_base, + BIT(11), 0); + PRCC_PCLK_STORE(clk, 2, 11); + + clk = clk_reg_prcc_pclk("p2_pclk12", "per2clk", clkrst2_base, + BIT(12), 0); + PRCC_PCLK_STORE(clk, 2, 12); + + clk = clk_reg_prcc_pclk("p3_pclk0", "per3clk", clkrst3_base, + BIT(0), 0); + PRCC_PCLK_STORE(clk, 3, 0); + + clk = clk_reg_prcc_pclk("p3_pclk1", "per3clk", clkrst3_base, + BIT(1), 0); + PRCC_PCLK_STORE(clk, 3, 1); + + clk = clk_reg_prcc_pclk("p3_pclk2", "per3clk", clkrst3_base, + BIT(2), 0); + PRCC_PCLK_STORE(clk, 3, 2); + + clk = clk_reg_prcc_pclk("p3_pclk3", "per3clk", clkrst3_base, + BIT(3), 0); + PRCC_PCLK_STORE(clk, 3, 3); + + clk = clk_reg_prcc_pclk("p3_pclk4", "per3clk", clkrst3_base, + BIT(4), 0); + PRCC_PCLK_STORE(clk, 3, 4); + + clk = clk_reg_prcc_pclk("p3_pclk5", "per3clk", clkrst3_base, + BIT(5), 0); + PRCC_PCLK_STORE(clk, 3, 5); + + clk = clk_reg_prcc_pclk("p3_pclk6", "per3clk", clkrst3_base, + BIT(6), 0); + PRCC_PCLK_STORE(clk, 3, 6); + + clk = clk_reg_prcc_pclk("p3_pclk7", "per3clk", clkrst3_base, + BIT(7), 0); + PRCC_PCLK_STORE(clk, 3, 7); + + clk = clk_reg_prcc_pclk("p3_pclk8", "per3clk", clkrst3_base, + BIT(8), 0); + PRCC_PCLK_STORE(clk, 3, 8); + + clk = clk_reg_prcc_pclk("p5_pclk0", "per5clk", clkrst5_base, + BIT(0), 0); + PRCC_PCLK_STORE(clk, 5, 0); + + clk = clk_reg_prcc_pclk("p5_pclk1", "per5clk", clkrst5_base, + BIT(1), 0); + PRCC_PCLK_STORE(clk, 5, 1); + + clk = clk_reg_prcc_pclk("p6_pclk0", "per6clk", clkrst6_base, + BIT(0), 0); + PRCC_PCLK_STORE(clk, 6, 0); + + clk = clk_reg_prcc_pclk("p6_pclk1", "per6clk", clkrst6_base, + BIT(1), 0); + PRCC_PCLK_STORE(clk, 6, 1); + + clk = clk_reg_prcc_pclk("p6_pclk2", "per6clk", clkrst6_base, + BIT(2), 0); + PRCC_PCLK_STORE(clk, 6, 2); + + clk = clk_reg_prcc_pclk("p6_pclk3", "per6clk", clkrst6_base, + BIT(3), 0); + PRCC_PCLK_STORE(clk, 6, 3); + + clk = clk_reg_prcc_pclk("p6_pclk4", "per6clk", clkrst6_base, + BIT(4), 0); + PRCC_PCLK_STORE(clk, 6, 4); + + clk = clk_reg_prcc_pclk("p6_pclk5", "per6clk", clkrst6_base, + BIT(5), 0); + PRCC_PCLK_STORE(clk, 6, 5); + + clk = clk_reg_prcc_pclk("p6_pclk6", "per6clk", clkrst6_base, + BIT(6), 0); + PRCC_PCLK_STORE(clk, 6, 6); + + clk = clk_reg_prcc_pclk("p6_pclk7", "per6clk", clkrst6_base, + BIT(7), 0); + PRCC_PCLK_STORE(clk, 6, 7); + + /* PRCC K-clocks + * + * FIXME: Some drivers requires PERPIH[n| to be automatically enabled + * by enabling just the K-clock, even if it is not a valid parent to + * the K-clock. Until drivers get fixed we might need some kind of + * "parent muxed join". + */ + + /* Periph1 */ + clk = clk_reg_prcc_kclk("p1_uart0_kclk", "uartclk", + clkrst1_base, BIT(0), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 0); + + clk = clk_reg_prcc_kclk("p1_uart1_kclk", "uartclk", + clkrst1_base, BIT(1), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 1); + + clk = clk_reg_prcc_kclk("p1_i2c1_kclk", "i2cclk", + clkrst1_base, BIT(2), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 2); + + clk = clk_reg_prcc_kclk("p1_msp0_kclk", "msp02clk", + clkrst1_base, BIT(3), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 3); + + clk = clk_reg_prcc_kclk("p1_msp1_kclk", "msp1clk", + clkrst1_base, BIT(4), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 4); + + clk = clk_reg_prcc_kclk("p1_sdi0_kclk", "sdmmcclk", + clkrst1_base, BIT(5), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 5); + + clk = clk_reg_prcc_kclk("p1_i2c2_kclk", "i2cclk", + clkrst1_base, BIT(6), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 6); + + clk = clk_reg_prcc_kclk("p1_slimbus0_kclk", "slimclk", + clkrst1_base, BIT(8), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 8); + + clk = clk_reg_prcc_kclk("p1_i2c4_kclk", "i2cclk", + clkrst1_base, BIT(9), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 9); + + clk = clk_reg_prcc_kclk("p1_msp3_kclk", "msp1clk", + clkrst1_base, BIT(10), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 1, 10); + + /* Periph2 */ + clk = clk_reg_prcc_kclk("p2_i2c3_kclk", "i2cclk", + clkrst2_base, BIT(0), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 2, 0); + + clk = clk_reg_prcc_kclk("p2_sdi4_kclk", "sdmmcclk", + clkrst2_base, BIT(2), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 2, 2); + + clk = clk_reg_prcc_kclk("p2_msp2_kclk", "msp02clk", + clkrst2_base, BIT(3), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 2, 3); + + clk = clk_reg_prcc_kclk("p2_sdi1_kclk", "sdmmcclk", + clkrst2_base, BIT(4), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 2, 4); + + clk = clk_reg_prcc_kclk("p2_sdi3_kclk", "sdmmcclk", + clkrst2_base, BIT(5), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 2, 5); + + /* Note that rate is received from parent. */ + clk = clk_reg_prcc_kclk("p2_ssirx_kclk", "hsirxclk", + clkrst2_base, BIT(6), + CLK_SET_RATE_GATE|CLK_SET_RATE_PARENT); + PRCC_KCLK_STORE(clk, 2, 6); + + clk = clk_reg_prcc_kclk("p2_ssitx_kclk", "hsitxclk", + clkrst2_base, BIT(7), + CLK_SET_RATE_GATE|CLK_SET_RATE_PARENT); + PRCC_KCLK_STORE(clk, 2, 7); + + /* Periph3 */ + clk = clk_reg_prcc_kclk("p3_ssp0_kclk", "sspclk", + clkrst3_base, BIT(1), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 3, 1); + + clk = clk_reg_prcc_kclk("p3_ssp1_kclk", "sspclk", + clkrst3_base, BIT(2), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 3, 2); + + clk = clk_reg_prcc_kclk("p3_i2c0_kclk", "i2cclk", + clkrst3_base, BIT(3), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 3, 3); + + clk = clk_reg_prcc_kclk("p3_sdi2_kclk", "sdmmcclk", + clkrst3_base, BIT(4), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 3, 4); + + clk = clk_reg_prcc_kclk("p3_ske_kclk", "rtc32k", + clkrst3_base, BIT(5), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 3, 5); + + clk = clk_reg_prcc_kclk("p3_uart2_kclk", "uartclk", + clkrst3_base, BIT(6), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 3, 6); + + clk = clk_reg_prcc_kclk("p3_sdi5_kclk", "sdmmcclk", + clkrst3_base, BIT(7), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 3, 7); + + /* Periph6 */ + clk = clk_reg_prcc_kclk("p3_rng_kclk", "rngclk", + clkrst6_base, BIT(0), CLK_SET_RATE_GATE); + PRCC_KCLK_STORE(clk, 6, 0); + + for_each_child_of_node(np, child) { + static struct clk_onecell_data clk_data; + + if (!of_node_cmp(child->name, "prcmu-clock")) { + clk_data.clks = prcmu_clk; + clk_data.clk_num = ARRAY_SIZE(prcmu_clk); + of_clk_add_provider(child, of_clk_src_onecell_get, &clk_data); + } + if (!of_node_cmp(child->name, "prcc-periph-clock")) + of_clk_add_provider(child, ux500_twocell_get, prcc_pclk); + + if (!of_node_cmp(child->name, "prcc-kernel-clock")) + of_clk_add_provider(child, ux500_twocell_get, prcc_kclk); + + if (!of_node_cmp(child->name, "rtc32k-clock")) + of_clk_add_provider(child, of_clk_src_simple_get, rtc_clk); + + if (!of_node_cmp(child->name, "smp-twd-clock")) + of_clk_add_provider(child, of_clk_src_simple_get, twd_clk); + } +} diff --git a/drivers/clk/ux500/u8540_clk.c b/drivers/clk/ux500/u8540_clk.c index f262588..20c8add 100644 --- a/drivers/clk/ux500/u8540_clk.c +++ b/drivers/clk/ux500/u8540_clk.c @@ -83,7 +83,7 @@ void u8540_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, clk_register_clkdev(clk, NULL, "lcd"); clk_register_clkdev(clk, "lcd", "mcde"); - clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BML8580CLK, + clk = clk_reg_prcmu_opp_gate("bmlclk", NULL, PRCMU_BMLCLK, CLK_IS_ROOT); clk_register_clkdev(clk, NULL, "bml"); diff --git a/drivers/gpio/gpio-samsung.c b/drivers/gpio/gpio-samsung.c index f6f1c7d..76e02b9 100644 --- a/drivers/gpio/gpio-samsung.c +++ b/drivers/gpio/gpio-samsung.c @@ -2082,34 +2082,14 @@ static __init int samsung_gpiolib_init(void) int i, nr_chips; int group = 0; -#if defined(CONFIG_PINCTRL_EXYNOS) || defined(CONFIG_PINCTRL_EXYNOS5440) /* - * This gpio driver includes support for device tree support and there - * are platforms using it. In order to maintain compatibility with those - * platforms, and to allow non-dt Exynos4210 platforms to use this - * gpiolib support, a check is added to find out if there is a active - * pin-controller driver support available. If it is available, this - * gpiolib support is ignored and the gpiolib support available in - * pin-controller driver is used. This is a temporary check and will go - * away when all of the Exynos4210 platforms have switched to using - * device tree and the pin-ctrl driver. - */ - struct device_node *pctrl_np; - static const struct of_device_id exynos_pinctrl_ids[] = { - { .compatible = "samsung,s3c2412-pinctrl", }, - { .compatible = "samsung,s3c2416-pinctrl", }, - { .compatible = "samsung,s3c2440-pinctrl", }, - { .compatible = "samsung,s3c2450-pinctrl", }, - { .compatible = "samsung,exynos4210-pinctrl", }, - { .compatible = "samsung,exynos4x12-pinctrl", }, - { .compatible = "samsung,exynos5250-pinctrl", }, - { .compatible = "samsung,exynos5440-pinctrl", }, - { } - }; - for_each_matching_node(pctrl_np, exynos_pinctrl_ids) - if (pctrl_np && of_device_is_available(pctrl_np)) - return -ENODEV; -#endif + * Currently there are two drivers that can provide GPIO support for + * Samsung SoCs. For device tree enabled platforms, the new + * pinctrl-samsung driver is used, providing both GPIO and pin control + * interfaces. For legacy (non-DT) platforms this driver is used. + */ + if (of_have_populated_dt()) + return -ENODEV; samsung_gpiolib_set_cfg(samsung_gpio_cfgs, ARRAY_SIZE(samsung_gpio_cfgs)); diff --git a/drivers/irqchip/irq-vic.c b/drivers/irqchip/irq-vic.c index 2bbb004..8e21ae0 100644 --- a/drivers/irqchip/irq-vic.c +++ b/drivers/irqchip/irq-vic.c @@ -469,6 +469,8 @@ void __init vic_init(void __iomem *base, unsigned int irq_start, int __init vic_of_init(struct device_node *node, struct device_node *parent) { void __iomem *regs; + u32 interrupt_mask = ~0; + u32 wakeup_mask = ~0; if (WARN(parent, "non-root VICs are not supported")) return -EINVAL; @@ -477,10 +479,13 @@ int __init vic_of_init(struct device_node *node, struct device_node *parent) if (WARN_ON(!regs)) return -EIO; + of_property_read_u32(node, "valid-mask", &interrupt_mask); + of_property_read_u32(node, "valid-wakeup-mask", &wakeup_mask); + /* * Passing 0 as first IRQ makes the simple domain allocate descriptors */ - __vic_init(regs, 0, ~0, ~0, node); + __vic_init(regs, 0, interrupt_mask, wakeup_mask, node); return 0; } diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c index 53f371d..b9ce60c 100644 --- a/drivers/mfd/db8500-prcmu.c +++ b/drivers/mfd/db8500-prcmu.c @@ -480,7 +480,6 @@ static struct clk_mgt clk_mgt[PRCMU_NUM_REG_CLOCKS] = { CLK_MGT_ENTRY(PER6CLK, PLL_DIV, true), CLK_MGT_ENTRY(PER7CLK, PLL_DIV, true), CLK_MGT_ENTRY(LCDCLK, PLL_FIX, true), - CLK_MGT_ENTRY(BML8580CLK, PLL_DIV, true), CLK_MGT_ENTRY(BMLCLK, PLL_DIV, true), CLK_MGT_ENTRY(HSITXCLK, PLL_DIV, true), CLK_MGT_ENTRY(HSIRXCLK, PLL_DIV, true), diff --git a/drivers/mfd/dbx500-prcmu-regs.h b/drivers/mfd/dbx500-prcmu-regs.h index 4f6f0fa..7cc32a8 100644 --- a/drivers/mfd/dbx500-prcmu-regs.h +++ b/drivers/mfd/dbx500-prcmu-regs.h @@ -32,7 +32,6 @@ #define PRCM_PER7CLK_MGT (0x040) #define PRCM_LCDCLK_MGT (0x044) #define PRCM_BMLCLK_MGT (0x04C) -#define PRCM_BML8580CLK_MGT (0x108) #define PRCM_HSITXCLK_MGT (0x050) #define PRCM_HSIRXCLK_MGT (0x054) #define PRCM_HDMICLK_MGT (0x058) diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c index a82ace4..0846922 100644 --- a/drivers/pinctrl/pinctrl-single.c +++ b/drivers/pinctrl/pinctrl-single.c @@ -15,15 +15,21 @@ #include <linux/slab.h> #include <linux/err.h> #include <linux/list.h> +#include <linux/interrupt.h> + +#include <linux/irqchip/chained_irq.h> #include <linux/of.h> #include <linux/of_device.h> #include <linux/of_address.h> +#include <linux/of_irq.h> #include <linux/pinctrl/pinctrl.h> #include <linux/pinctrl/pinmux.h> #include <linux/pinctrl/pinconf-generic.h> +#include <linux/platform_data/pinctrl-single.h> + #include "core.h" #include "pinconf.h" @@ -150,19 +156,36 @@ struct pcs_name { }; /** + * struct pcs_soc_data - SoC specific settings + * @flags: initial SoC specific PCS_FEAT_xxx values + * @irq: optional interrupt for the controller + * @irq_enable_mask: optional SoC specific interrupt enable mask + * @irq_status_mask: optional SoC specific interrupt status mask + * @rearm: optional SoC specific wake-up rearm function + */ +struct pcs_soc_data { + unsigned flags; + int irq; + unsigned irq_enable_mask; + unsigned irq_status_mask; + void (*rearm)(void); +}; + +/** * struct pcs_device - pinctrl device instance * @res: resources * @base: virtual address of the controller * @size: size of the ioremapped area * @dev: device entry * @pctl: pin controller device + * @flags: mask of PCS_FEAT_xxx values + * @lock: spinlock for register access * @mutex: mutex protecting the lists * @width: bits per mux register * @fmask: function register mask * @fshift: function register shift * @foff: value to turn mux off * @fmax: max number of functions in fmask - * @is_pinconf: whether supports pinconf * @bits_per_pin:number of bits per pin * @names: array of register names for pins * @pins: physical pins on the SoC @@ -171,6 +194,9 @@ struct pcs_name { * @pingroups: list of pingroups * @functions: list of functions * @gpiofuncs: list of gpio functions + * @irqs: list of interrupt registers + * @chip: chip container for this instance + * @domain: IRQ domain for this instance * @ngroups: number of pingroups * @nfuncs: number of functions * @desc: pin controller descriptor @@ -183,6 +209,12 @@ struct pcs_device { unsigned size; struct device *dev; struct pinctrl_dev *pctl; + unsigned flags; +#define PCS_QUIRK_SHARED_IRQ (1 << 2) +#define PCS_FEAT_IRQ (1 << 1) +#define PCS_FEAT_PINCONF (1 << 0) + struct pcs_soc_data socdata; + raw_spinlock_t lock; struct mutex mutex; unsigned width; unsigned fmask; @@ -190,7 +222,6 @@ struct pcs_device { unsigned foff; unsigned fmax; bool bits_per_mux; - bool is_pinconf; unsigned bits_per_pin; struct pcs_name *names; struct pcs_data pins; @@ -199,6 +230,9 @@ struct pcs_device { struct list_head pingroups; struct list_head functions; struct list_head gpiofuncs; + struct list_head irqs; + struct irq_chip chip; + struct irq_domain *domain; unsigned ngroups; unsigned nfuncs; struct pinctrl_desc desc; @@ -206,6 +240,10 @@ struct pcs_device { void (*write)(unsigned val, void __iomem *reg); }; +#define PCS_QUIRK_HAS_SHARED_IRQ (pcs->flags & PCS_QUIRK_SHARED_IRQ) +#define PCS_HAS_IRQ (pcs->flags & PCS_FEAT_IRQ) +#define PCS_HAS_PINCONF (pcs->flags & PCS_FEAT_PINCONF) + static int pcs_pinconf_get(struct pinctrl_dev *pctldev, unsigned pin, unsigned long *config); static int pcs_pinconf_set(struct pinctrl_dev *pctldev, unsigned pin, @@ -429,9 +467,11 @@ static int pcs_enable(struct pinctrl_dev *pctldev, unsigned fselector, for (i = 0; i < func->nvals; i++) { struct pcs_func_vals *vals; + unsigned long flags; unsigned val, mask; vals = &func->vals[i]; + raw_spin_lock_irqsave(&pcs->lock, flags); val = pcs->read(vals->reg); if (pcs->bits_per_mux) @@ -442,6 +482,7 @@ static int pcs_enable(struct pinctrl_dev *pctldev, unsigned fselector, val &= ~mask; val |= (vals->val & mask); pcs->write(val, vals->reg); + raw_spin_unlock_irqrestore(&pcs->lock, flags); } return 0; @@ -483,13 +524,16 @@ static void pcs_disable(struct pinctrl_dev *pctldev, unsigned fselector, for (i = 0; i < func->nvals; i++) { struct pcs_func_vals *vals; + unsigned long flags; unsigned val; vals = &func->vals[i]; + raw_spin_lock_irqsave(&pcs->lock, flags); val = pcs->read(vals->reg); val &= ~pcs->fmask; val |= pcs->foff << pcs->fshift; pcs->write(val, vals->reg); + raw_spin_unlock_irqrestore(&pcs->lock, flags); } } @@ -1060,7 +1104,7 @@ static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np, }; /* If pinconf isn't supported, don't parse properties in below. */ - if (!pcs->is_pinconf) + if (!PCS_HAS_PINCONF) return 0; /* cacluate how much properties are supported in current node */ @@ -1184,7 +1228,7 @@ static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs, (*map)->data.mux.group = np->name; (*map)->data.mux.function = np->name; - if (pcs->is_pinconf) { + if (PCS_HAS_PINCONF) { res = pcs_parse_pinconf(pcs, np, function, map); if (res) goto free_pingroups; @@ -1305,7 +1349,7 @@ static int pcs_parse_bits_in_pinctrl_entry(struct pcs_device *pcs, (*map)->data.mux.group = np->name; (*map)->data.mux.function = np->name; - if (pcs->is_pinconf) { + if (PCS_HAS_PINCONF) { dev_err(pcs->dev, "pinconf not supported\n"); goto free_pingroups; } @@ -1440,11 +1484,33 @@ static void pcs_free_pingroups(struct pcs_device *pcs) } /** + * pcs_irq_free() - free interrupt + * @pcs: pcs driver instance + */ +static void pcs_irq_free(struct pcs_device *pcs) +{ + struct pcs_soc_data *pcs_soc = &pcs->socdata; + + if (pcs_soc->irq < 0) + return; + + if (pcs->domain) + irq_domain_remove(pcs->domain); + + if (PCS_QUIRK_HAS_SHARED_IRQ) + free_irq(pcs_soc->irq, pcs_soc); + else + irq_set_chained_handler(pcs_soc->irq, NULL); +} + +/** * pcs_free_resources() - free memory used by this driver * @pcs: pcs driver instance */ static void pcs_free_resources(struct pcs_device *pcs) { + pcs_irq_free(pcs); + if (pcs->pctl) pinctrl_unregister(pcs->pctl); @@ -1493,6 +1559,268 @@ static int pcs_add_gpio_func(struct device_node *node, struct pcs_device *pcs) } return ret; } +/** + * @reg: virtual address of interrupt register + * @hwirq: hardware irq number + * @irq: virtual irq number + * @node: list node + */ +struct pcs_interrupt { + void __iomem *reg; + irq_hw_number_t hwirq; + unsigned int irq; + struct list_head node; +}; + +/** + * pcs_irq_set() - enables or disables an interrupt + * + * Note that this currently assumes one interrupt per pinctrl + * register that is typically used for wake-up events. + */ +static inline void pcs_irq_set(struct pcs_soc_data *pcs_soc, + int irq, const bool enable) +{ + struct pcs_device *pcs; + struct list_head *pos; + unsigned mask; + + pcs = container_of(pcs_soc, struct pcs_device, socdata); + list_for_each(pos, &pcs->irqs) { + struct pcs_interrupt *pcswi; + unsigned soc_mask; + + pcswi = list_entry(pos, struct pcs_interrupt, node); + if (irq != pcswi->irq) + continue; + + soc_mask = pcs_soc->irq_enable_mask; + raw_spin_lock(&pcs->lock); + mask = pcs->read(pcswi->reg); + if (enable) + mask |= soc_mask; + else + mask &= ~soc_mask; + pcs->write(mask, pcswi->reg); + raw_spin_unlock(&pcs->lock); + } +} + +/** + * pcs_irq_mask() - mask pinctrl interrupt + * @d: interrupt data + */ +static void pcs_irq_mask(struct irq_data *d) +{ + struct pcs_soc_data *pcs_soc = irq_data_get_irq_chip_data(d); + + pcs_irq_set(pcs_soc, d->irq, false); +} + +/** + * pcs_irq_unmask() - unmask pinctrl interrupt + * @d: interrupt data + */ +static void pcs_irq_unmask(struct irq_data *d) +{ + struct pcs_soc_data *pcs_soc = irq_data_get_irq_chip_data(d); + + pcs_irq_set(pcs_soc, d->irq, true); + if (pcs_soc->rearm) + pcs_soc->rearm(); +} + +/** + * pcs_irq_set_wake() - toggle the suspend and resume wake up + * @d: interrupt data + * @state: wake-up state + * + * Note that this should be called only for suspend and resume. + * For runtime PM, the wake-up events should be enabled by default. + */ +static int pcs_irq_set_wake(struct irq_data *d, unsigned int state) +{ + if (state) + pcs_irq_unmask(d); + else + pcs_irq_mask(d); + + return 0; +} + +/** + * pcs_irq_handle() - common interrupt handler + * @pcs_irq: interrupt data + * + * Note that this currently assumes we have one interrupt bit per + * mux register. This interrupt is typically used for wake-up events. + * For more complex interrupts different handlers can be specified. + */ +static int pcs_irq_handle(struct pcs_soc_data *pcs_soc) +{ + struct pcs_device *pcs; + struct list_head *pos; + int count = 0; + + pcs = container_of(pcs_soc, struct pcs_device, socdata); + list_for_each(pos, &pcs->irqs) { + struct pcs_interrupt *pcswi; + unsigned mask; + + pcswi = list_entry(pos, struct pcs_interrupt, node); + raw_spin_lock(&pcs->lock); + mask = pcs->read(pcswi->reg); + raw_spin_unlock(&pcs->lock); + if (mask & pcs_soc->irq_status_mask) { + generic_handle_irq(irq_find_mapping(pcs->domain, + pcswi->hwirq)); + count++; + } + } + + /* + * For debugging on omaps, you may want to call pcs_soc->rearm() + * here to see wake-up interrupts during runtime also. + */ + + return count; +} + +/** + * pcs_irq_handler() - handler for the shared interrupt case + * @irq: interrupt + * @d: data + * + * Use this for cases where multiple instances of + * pinctrl-single share a single interrupt like on omaps. + */ +static irqreturn_t pcs_irq_handler(int irq, void *d) +{ + struct pcs_soc_data *pcs_soc = d; + + return pcs_irq_handle(pcs_soc) ? IRQ_HANDLED : IRQ_NONE; +} + +/** + * pcs_irq_handle() - handler for the dedicated chained interrupt case + * @irq: interrupt + * @desc: interrupt descriptor + * + * Use this if you have a separate interrupt for each + * pinctrl-single instance. + */ +static void pcs_irq_chain_handler(unsigned int irq, struct irq_desc *desc) +{ + struct pcs_soc_data *pcs_soc = irq_desc_get_handler_data(desc); + struct irq_chip *chip; + int res; + + chip = irq_get_chip(irq); + chained_irq_enter(chip, desc); + res = pcs_irq_handle(pcs_soc); + /* REVISIT: export and add handle_bad_irq(irq, desc)? */ + chained_irq_exit(chip, desc); + + return; +} + +static int pcs_irqdomain_map(struct irq_domain *d, unsigned int irq, + irq_hw_number_t hwirq) +{ + struct pcs_soc_data *pcs_soc = d->host_data; + struct pcs_device *pcs; + struct pcs_interrupt *pcswi; + + pcs = container_of(pcs_soc, struct pcs_device, socdata); + pcswi = devm_kzalloc(pcs->dev, sizeof(*pcswi), GFP_KERNEL); + if (!pcswi) + return -ENOMEM; + + pcswi->reg = pcs->base + hwirq; + pcswi->hwirq = hwirq; + pcswi->irq = irq; + + mutex_lock(&pcs->mutex); + list_add_tail(&pcswi->node, &pcs->irqs); + mutex_unlock(&pcs->mutex); + + irq_set_chip_data(irq, pcs_soc); + irq_set_chip_and_handler(irq, &pcs->chip, + handle_level_irq); + +#ifdef CONFIG_ARM + set_irq_flags(irq, IRQF_VALID); +#else + irq_set_noprobe(irq); +#endif + + return 0; +} + +static struct irq_domain_ops pcs_irqdomain_ops = { + .map = pcs_irqdomain_map, + .xlate = irq_domain_xlate_onecell, +}; + +/** + * pcs_irq_init_chained_handler() - set up a chained interrupt handler + * @pcs: pcs driver instance + * @np: device node pointer + */ +static int pcs_irq_init_chained_handler(struct pcs_device *pcs, + struct device_node *np) +{ + struct pcs_soc_data *pcs_soc = &pcs->socdata; + const char *name = "pinctrl"; + int num_irqs; + + if (!pcs_soc->irq_enable_mask || + !pcs_soc->irq_status_mask) { + pcs_soc->irq = -1; + return -EINVAL; + } + + INIT_LIST_HEAD(&pcs->irqs); + pcs->chip.name = name; + pcs->chip.irq_ack = pcs_irq_mask; + pcs->chip.irq_mask = pcs_irq_mask; + pcs->chip.irq_unmask = pcs_irq_unmask; + pcs->chip.irq_set_wake = pcs_irq_set_wake; + + if (PCS_QUIRK_HAS_SHARED_IRQ) { + int res; + + res = request_irq(pcs_soc->irq, pcs_irq_handler, + IRQF_SHARED | IRQF_NO_SUSPEND, + name, pcs_soc); + if (res) { + pcs_soc->irq = -1; + return res; + } + } else { + irq_set_handler_data(pcs_soc->irq, pcs_soc); + irq_set_chained_handler(pcs_soc->irq, + pcs_irq_chain_handler); + } + + /* + * We can use the register offset as the hardirq + * number as irq_domain_add_simple maps them lazily. + * This way we can easily support more than one + * interrupt per function if needed. + */ + num_irqs = pcs->size; + + pcs->domain = irq_domain_add_simple(np, num_irqs, 0, + &pcs_irqdomain_ops, + pcs_soc); + if (!pcs->domain) { + irq_set_chained_handler(pcs_soc->irq, NULL); + return -EINVAL; + } + + return 0; +} #ifdef CONFIG_PM static int pinctrl_single_suspend(struct platform_device *pdev, @@ -1523,8 +1851,10 @@ static int pcs_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; const struct of_device_id *match; + struct pcs_pdata *pdata; struct resource *res; struct pcs_device *pcs; + const struct pcs_soc_data *soc; int ret; match = of_match_device(pcs_of_match, &pdev->dev); @@ -1537,11 +1867,14 @@ static int pcs_probe(struct platform_device *pdev) return -ENOMEM; } pcs->dev = &pdev->dev; + raw_spin_lock_init(&pcs->lock); mutex_init(&pcs->mutex); INIT_LIST_HEAD(&pcs->pingroups); INIT_LIST_HEAD(&pcs->functions); INIT_LIST_HEAD(&pcs->gpiofuncs); - pcs->is_pinconf = match->data; + soc = match->data; + pcs->flags = soc->flags; + memcpy(&pcs->socdata, soc, sizeof(*soc)); PCS_GET_PROP_U32("pinctrl-single,register-width", &pcs->width, "register width not specified\n"); @@ -1610,7 +1943,7 @@ static int pcs_probe(struct platform_device *pdev) pcs->desc.name = DRIVER_NAME; pcs->desc.pctlops = &pcs_pinctrl_ops; pcs->desc.pmxops = &pcs_pinmux_ops; - if (pcs->is_pinconf) + if (PCS_HAS_PINCONF) pcs->desc.confops = &pcs_pinconf_ops; pcs->desc.owner = THIS_MODULE; @@ -1629,6 +1962,27 @@ static int pcs_probe(struct platform_device *pdev) if (ret < 0) goto free; + pcs->socdata.irq = irq_of_parse_and_map(np, 0); + if (pcs->socdata.irq) + pcs->flags |= PCS_FEAT_IRQ; + + /* We still need auxdata for some omaps for PRM interrupts */ + pdata = dev_get_platdata(&pdev->dev); + if (pdata) { + if (pdata->rearm) + pcs->socdata.rearm = pdata->rearm; + if (pdata->irq) { + pcs->socdata.irq = pdata->irq; + pcs->flags |= PCS_FEAT_IRQ; + } + } + + if (PCS_HAS_IRQ) { + ret = pcs_irq_init_chained_handler(pcs, np); + if (ret < 0) + dev_warn(pcs->dev, "initialized with no interrupts\n"); + } + dev_info(pcs->dev, "%i pins at pa %p size %u\n", pcs->desc.npins, pcs->base, pcs->size); @@ -1652,9 +2006,25 @@ static int pcs_remove(struct platform_device *pdev) return 0; } +static const struct pcs_soc_data pinctrl_single_omap_wkup = { + .flags = PCS_QUIRK_SHARED_IRQ, + .irq_enable_mask = (1 << 14), /* OMAP_WAKEUP_EN */ + .irq_status_mask = (1 << 15), /* OMAP_WAKEUP_EVENT */ +}; + +static const struct pcs_soc_data pinctrl_single = { +}; + +static const struct pcs_soc_data pinconf_single = { + .flags = PCS_FEAT_PINCONF, +}; + static struct of_device_id pcs_of_match[] = { - { .compatible = "pinctrl-single", .data = (void *)false }, - { .compatible = "pinconf-single", .data = (void *)true }, + { .compatible = "ti,omap3-padconf", .data = &pinctrl_single_omap_wkup }, + { .compatible = "ti,omap4-padconf", .data = &pinctrl_single_omap_wkup }, + { .compatible = "ti,omap5-padconf", .data = &pinctrl_single_omap_wkup }, + { .compatible = "pinctrl-single", .data = &pinctrl_single }, + { .compatible = "pinconf-single", .data = &pinconf_single }, { }, }; MODULE_DEVICE_TABLE(of, pcs_of_match); diff --git a/drivers/usb/musb/ux500.c b/drivers/usb/musb/ux500.c index f483d19..122446b 100644 --- a/drivers/usb/musb/ux500.c +++ b/drivers/usb/musb/ux500.c @@ -259,7 +259,7 @@ static int ux500_probe(struct platform_device *pdev) goto err1; } - clk = clk_get(&pdev->dev, "usb"); + clk = clk_get(&pdev->dev, NULL); if (IS_ERR(clk)) { dev_err(&pdev->dev, "failed to get clock\n"); ret = PTR_ERR(clk); diff --git a/include/dt-bindings/mfd/dbx500-prcmu.h b/include/dt-bindings/mfd/dbx500-prcmu.h new file mode 100644 index 0000000..552a2d1 --- /dev/null +++ b/include/dt-bindings/mfd/dbx500-prcmu.h @@ -0,0 +1,83 @@ +/* + * This header provides constants for the PRCMU bindings. + * + */ + +#ifndef _DT_BINDINGS_MFD_PRCMU_H +#define _DT_BINDINGS_MFD_PRCMU_H + +/* + * Clock identifiers. + */ +#define ARMCLK 0 +#define PRCMU_ACLK 1 +#define PRCMU_SVAMMCSPCLK 2 +#define PRCMU_SDMMCHCLK 2 /* DBx540 only. */ +#define PRCMU_SIACLK 3 +#define PRCMU_SIAMMDSPCLK 3 /* DBx540 only. */ +#define PRCMU_SGACLK 4 +#define PRCMU_UARTCLK 5 +#define PRCMU_MSP02CLK 6 +#define PRCMU_MSP1CLK 7 +#define PRCMU_I2CCLK 8 +#define PRCMU_SDMMCCLK 9 +#define PRCMU_SLIMCLK 10 +#define PRCMU_CAMCLK 10 /* DBx540 only. */ +#define PRCMU_PER1CLK 11 +#define PRCMU_PER2CLK 12 +#define PRCMU_PER3CLK 13 +#define PRCMU_PER5CLK 14 +#define PRCMU_PER6CLK 15 +#define PRCMU_PER7CLK 16 +#define PRCMU_LCDCLK 17 +#define PRCMU_BMLCLK 18 +#define PRCMU_HSITXCLK 19 +#define PRCMU_HSIRXCLK 20 +#define PRCMU_HDMICLK 21 +#define PRCMU_APEATCLK 22 +#define PRCMU_APETRACECLK 23 +#define PRCMU_MCDECLK 24 +#define PRCMU_IPI2CCLK 25 +#define PRCMU_DSIALTCLK 26 +#define PRCMU_DMACLK 27 +#define PRCMU_B2R2CLK 28 +#define PRCMU_TVCLK 29 +#define SPARE_UNIPROCLK 30 +#define PRCMU_SSPCLK 31 +#define PRCMU_RNGCLK 32 +#define PRCMU_UICCCLK 33 +#define PRCMU_G1CLK 34 /* DBx540 only. */ +#define PRCMU_HVACLK 35 /* DBx540 only. */ +#define PRCMU_SPARE1CLK 36 +#define PRCMU_SPARE2CLK 37 + +#define PRCMU_NUM_REG_CLOCKS 38 + +#define PRCMU_RTCCLK PRCMU_NUM_REG_CLOCKS +#define PRCMU_SYSCLK 39 +#define PRCMU_CDCLK 40 +#define PRCMU_TIMCLK 41 +#define PRCMU_PLLSOC0 42 +#define PRCMU_PLLSOC1 43 +#define PRCMU_ARMSS 44 +#define PRCMU_PLLDDR 45 + +/* DSI Clocks */ +#define PRCMU_PLLDSI 46 +#define PRCMU_DSI0CLK 47 +#define PRCMU_DSI1CLK 48 +#define PRCMU_DSI0ESCCLK 49 +#define PRCMU_DSI1ESCCLK 50 +#define PRCMU_DSI2ESCCLK 51 + +/* LCD DSI PLL - Ux540 only */ +#define PRCMU_PLLDSI_LCD 52 +#define PRCMU_DSI0CLK_LCD 53 +#define PRCMU_DSI1CLK_LCD 54 +#define PRCMU_DSI0ESCCLK_LCD 55 +#define PRCMU_DSI1ESCCLK_LCD 56 +#define PRCMU_DSI2ESCCLK_LCD 57 + +#define PRCMU_NUM_CLKS 58 + +#endif diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h new file mode 100644 index 0000000..eb6c366a --- /dev/null +++ b/include/dt-bindings/pinctrl/am43xx.h @@ -0,0 +1,31 @@ +/* + * This header provides constants specific to AM43XX pinctrl bindings. + */ + +#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H +#define _DT_BINDINGS_PINCTRL_AM43XX_H + +#define MUX_MODE0 0 +#define MUX_MODE1 1 +#define MUX_MODE2 2 +#define MUX_MODE3 3 +#define MUX_MODE4 4 +#define MUX_MODE5 5 +#define MUX_MODE6 6 +#define MUX_MODE7 7 + +#define PULL_DISABLE (1 << 16) +#define PULL_UP (1 << 17) +#define INPUT_EN (1 << 18) +#define SLEWCTRL_FAST (1 << 19) +#define DS0_PULL_UP_DOWN_EN (1 << 27) + +#define PIN_OUTPUT (PULL_DISABLE) +#define PIN_OUTPUT_PULLUP (PULL_UP) +#define PIN_OUTPUT_PULLDOWN 0 +#define PIN_INPUT (INPUT_EN | PULL_DISABLE) +#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP) +#define PIN_INPUT_PULLDOWN (INPUT_EN) + +#endif + diff --git a/include/dt-bindings/pinctrl/dra.h b/include/dt-bindings/pinctrl/dra.h new file mode 100644 index 0000000..002a285 --- /dev/null +++ b/include/dt-bindings/pinctrl/dra.h @@ -0,0 +1,50 @@ +/* + * This header provides constants for DRA pinctrl bindings. + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * Author: Rajendra Nayak <rnayak@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef _DT_BINDINGS_PINCTRL_DRA_H +#define _DT_BINDINGS_PINCTRL_DRA_H + +/* DRA7 mux mode options for each pin. See TRM for options */ +#define MUX_MODE0 0x0 +#define MUX_MODE1 0x1 +#define MUX_MODE2 0x2 +#define MUX_MODE3 0x3 +#define MUX_MODE4 0x4 +#define MUX_MODE5 0x5 +#define MUX_MODE6 0x6 +#define MUX_MODE7 0x7 +#define MUX_MODE8 0x8 +#define MUX_MODE9 0x9 +#define MUX_MODE10 0xa +#define MUX_MODE11 0xb +#define MUX_MODE12 0xc +#define MUX_MODE13 0xd +#define MUX_MODE14 0xe +#define MUX_MODE15 0xf + +#define PULL_ENA (1 << 16) +#define PULL_UP (1 << 17) +#define INPUT_EN (1 << 18) +#define SLEWCONTROL (1 << 19) +#define WAKEUP_EN (1 << 24) +#define WAKEUP_EVENT (1 << 25) + +/* Active pin states */ +#define PIN_OUTPUT 0 +#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP) +#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA) +#define PIN_INPUT INPUT_EN +#define PIN_INPUT_SLEW (INPUT_EN | SLEWCONTROL) +#define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP) +#define PIN_INPUT_PULLDOWN (PULL_ENA | INPUT_EN) + +#endif + diff --git a/include/linux/mfd/dbx500-prcmu.h b/include/linux/mfd/dbx500-prcmu.h index ca0790f..060e112 100644 --- a/include/linux/mfd/dbx500-prcmu.h +++ b/include/linux/mfd/dbx500-prcmu.h @@ -12,6 +12,8 @@ #include <linux/notifier.h> #include <linux/err.h> +#include <dt-bindings/mfd/dbx500-prcmu.h> /* For clock identifiers */ + /* Offset for the firmware version within the TCPM */ #define DB8500_PRCMU_FW_VERSION_OFFSET 0xA4 #define DBX540_PRCMU_FW_VERSION_OFFSET 0xA8 @@ -94,74 +96,6 @@ enum prcmu_wakeup_index { #define PRCMU_CLKSRC_ARMCLKFIX 0x46 #define PRCMU_CLKSRC_HDMICLK 0x47 -/* - * Clock identifiers. - */ -enum prcmu_clock { - PRCMU_SGACLK, - PRCMU_UARTCLK, - PRCMU_MSP02CLK, - PRCMU_MSP1CLK, - PRCMU_I2CCLK, - PRCMU_SDMMCCLK, - PRCMU_SPARE1CLK, - PRCMU_SLIMCLK, - PRCMU_PER1CLK, - PRCMU_PER2CLK, - PRCMU_PER3CLK, - PRCMU_PER5CLK, - PRCMU_PER6CLK, - PRCMU_PER7CLK, - PRCMU_LCDCLK, - PRCMU_BMLCLK, - PRCMU_HSITXCLK, - PRCMU_HSIRXCLK, - PRCMU_HDMICLK, - PRCMU_APEATCLK, - PRCMU_APETRACECLK, - PRCMU_MCDECLK, - PRCMU_IPI2CCLK, - PRCMU_DSIALTCLK, - PRCMU_DMACLK, - PRCMU_B2R2CLK, - PRCMU_TVCLK, - PRCMU_SSPCLK, - PRCMU_RNGCLK, - PRCMU_UICCCLK, - PRCMU_PWMCLK, - PRCMU_IRDACLK, - PRCMU_IRRCCLK, - PRCMU_SIACLK, - PRCMU_SVACLK, - PRCMU_ACLK, - PRCMU_HVACLK, /* Ux540 only */ - PRCMU_G1CLK, /* Ux540 only */ - PRCMU_SDMMCHCLK, - PRCMU_CAMCLK, - PRCMU_BML8580CLK, - PRCMU_NUM_REG_CLOCKS, - PRCMU_SYSCLK = PRCMU_NUM_REG_CLOCKS, - PRCMU_CDCLK, - PRCMU_TIMCLK, - PRCMU_PLLSOC0, - PRCMU_PLLSOC1, - PRCMU_ARMSS, - PRCMU_PLLDDR, - PRCMU_PLLDSI, - PRCMU_DSI0CLK, - PRCMU_DSI1CLK, - PRCMU_DSI0ESCCLK, - PRCMU_DSI1ESCCLK, - PRCMU_DSI2ESCCLK, - /* LCD DSI PLL - Ux540 only */ - PRCMU_PLLDSI_LCD, - PRCMU_DSI0CLK_LCD, - PRCMU_DSI1CLK_LCD, - PRCMU_DSI0ESCCLK_LCD, - PRCMU_DSI1ESCCLK_LCD, - PRCMU_DSI2ESCCLK_LCD, -}; - /** * enum prcmu_wdog_id - PRCMU watchdog IDs * @PRCMU_WDOG_ALL: use all timers diff --git a/include/linux/platform_data/clk-ux500.h b/include/linux/platform_data/clk-ux500.h index 9d98f3a..97baf83 100644 --- a/include/linux/platform_data/clk-ux500.h +++ b/include/linux/platform_data/clk-ux500.h @@ -10,6 +10,9 @@ #ifndef __CLK_UX500_H #define __CLK_UX500_H +void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, + u32 clkrst5_base, u32 clkrst6_base); + void u8500_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, u32 clkrst5_base, u32 clkrst6_base); void u9540_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, diff --git a/include/linux/platform_data/pinctrl-single.h b/include/linux/platform_data/pinctrl-single.h new file mode 100644 index 0000000..72eacda --- /dev/null +++ b/include/linux/platform_data/pinctrl-single.h @@ -0,0 +1,12 @@ +/** + * irq: optional wake-up interrupt + * rearm: optional soc specific rearm function + * + * Note that the irq and rearm setup should come from device + * tree except for omap where there are still some dependencies + * to the legacy PRM code. + */ +struct pcs_pdata { + int irq; + void (*rearm)(void); +}; |
