diff options
| -rw-r--r-- | drivers/char/watchdog/pcwd_pci.c | 175 |
1 files changed, 108 insertions, 67 deletions
diff --git a/drivers/char/watchdog/pcwd_pci.c b/drivers/char/watchdog/pcwd_pci.c index 5a80adb..0cb62e3 100644 --- a/drivers/char/watchdog/pcwd_pci.c +++ b/drivers/char/watchdog/pcwd_pci.c @@ -50,8 +50,8 @@ #include <asm/io.h> /* For inb/outb/... */ /* Module and version information */ -#define WATCHDOG_VERSION "1.01" -#define WATCHDOG_DATE "02 Sep 2005" +#define WATCHDOG_VERSION "1.02" +#define WATCHDOG_DATE "03 Sep 2005" #define WATCHDOG_DRIVER_NAME "PCI-PC Watchdog" #define WATCHDOG_NAME "pcwd_pci" #define PFX WATCHDOG_NAME ": " @@ -70,19 +70,30 @@ * These are the defines that describe the control status bits for the * PCI-PC Watchdog card. */ -#define WD_PCI_WTRP 0x01 /* Watchdog Trip status */ -#define WD_PCI_HRBT 0x02 /* Watchdog Heartbeat */ -#define WD_PCI_TTRP 0x04 /* Temperature Trip status */ +/* Port 1 : Control Status #1 */ +#define WD_PCI_WTRP 0x01 /* Watchdog Trip status */ +#define WD_PCI_HRBT 0x02 /* Watchdog Heartbeat */ +#define WD_PCI_TTRP 0x04 /* Temperature Trip status */ +#define WD_PCI_RL2A 0x08 /* Relay 2 Active */ +#define WD_PCI_RL1A 0x10 /* Relay 1 Active */ +#define WD_PCI_R2DS 0x40 /* Relay 2 Disable Temperature-trip/reset */ +#define WD_PCI_RLY2 0x80 /* Activate Relay 2 on the board */ +/* Port 2 : Control Status #2 */ +#define WD_PCI_WDIS 0x10 /* Watchdog Disable */ +#define WD_PCI_ENTP 0x20 /* Enable Temperature Trip Reset */ +#define WD_PCI_WRSP 0x40 /* Watchdog wrote response */ +#define WD_PCI_PCMD 0x80 /* PC has sent command */ /* according to documentation max. time to process a command for the pci * watchdog card is 100 ms, so we give it 150 ms to do it's job */ #define PCI_COMMAND_TIMEOUT 150 /* Watchdog's internal commands */ -#define CMD_GET_STATUS 0x04 -#define CMD_GET_FIRMWARE_VERSION 0x08 -#define CMD_READ_WATCHDOG_TIMEOUT 0x18 -#define CMD_WRITE_WATCHDOG_TIMEOUT 0x19 +#define CMD_GET_STATUS 0x04 +#define CMD_GET_FIRMWARE_VERSION 0x08 +#define CMD_READ_WATCHDOG_TIMEOUT 0x18 +#define CMD_WRITE_WATCHDOG_TIMEOUT 0x19 +#define CMD_GET_CLEAR_RESET_COUNT 0x84 /* We can only use 1 card due to the /dev/watchdog restriction */ static int cards_found; @@ -91,12 +102,12 @@ static int cards_found; static int temp_panic; static unsigned long is_active; static char expect_release; -static struct { - int supports_temp; /* Wether or not the card has a temperature device */ - int boot_status; /* The card's boot status */ - unsigned long io_addr; /* The cards I/O address */ - spinlock_t io_lock; - struct pci_dev *pdev; +static struct { /* this is private data for each PCI-PC watchdog card */ + int supports_temp; /* Wether or not the card has a temperature device */ + int boot_status; /* The card's boot status */ + unsigned long io_addr; /* The cards I/O address */ + spinlock_t io_lock; /* the lock for io operations */ + struct pci_dev *pdev; /* the PCI-device */ } pcipcwd_private; /* module parameters */ @@ -131,10 +142,10 @@ static int send_command(int cmd, int *msb, int *lsb) /* wait till the pci card processed the command, signaled by * the WRSP bit in port 2 and give it a max. timeout of * PCI_COMMAND_TIMEOUT to process */ - got_response = inb_p(pcipcwd_private.io_addr + 2) & 0x40; + got_response = inb_p(pcipcwd_private.io_addr + 2) & WD_PCI_WRSP; for (count = 0; (count < PCI_COMMAND_TIMEOUT) && (!got_response); count++) { mdelay(1); - got_response = inb_p(pcipcwd_private.io_addr + 2) & 0x40; + got_response = inb_p(pcipcwd_private.io_addr + 2) & WD_PCI_WRSP; } if (got_response) { @@ -150,6 +161,55 @@ static int send_command(int cmd, int *msb, int *lsb) return got_response; } +static inline void pcipcwd_check_temperature_support(void) +{ + if (inb_p(pcipcwd_private.io_addr) != 0xF0) + pcipcwd_private.supports_temp = 1; +} + +static int pcipcwd_get_option_switches(void) +{ + int option_switches; + + option_switches = inb_p(pcipcwd_private.io_addr + 3); + return option_switches; +} + +static void pcipcwd_show_card_info(void) +{ + int got_fw_rev, fw_rev_major, fw_rev_minor; + char fw_ver_str[20]; /* The cards firmware version */ + int option_switches; + + got_fw_rev = send_command(CMD_GET_FIRMWARE_VERSION, &fw_rev_major, &fw_rev_minor); + if (got_fw_rev) { + sprintf(fw_ver_str, "%u.%02u", fw_rev_major, fw_rev_minor); + } else { + sprintf(fw_ver_str, "<card no answer>"); + } + + /* Get switch settings */ + option_switches = pcipcwd_get_option_switches(); + + printk(KERN_INFO PFX "Found card at port 0x%04x (Firmware: %s) %s temp option\n", + (int) pcipcwd_private.io_addr, fw_ver_str, + (pcipcwd_private.supports_temp ? "with" : "without")); + + printk(KERN_INFO PFX "Option switches (0x%02x): Temperature Reset Enable=%s, Power On Delay=%s\n", + option_switches, + ((option_switches & 0x10) ? "ON" : "OFF"), + ((option_switches & 0x08) ? "ON" : "OFF")); + + if (pcipcwd_private.boot_status & WDIOF_CARDRESET) + printk(KERN_INFO PFX "Previous reset was caused by the Watchdog card\n"); + + if (pcipcwd_private.boot_status & WDIOF_OVERHEAT) + printk(KERN_INFO PFX "Card sensed a CPU Overheat\n"); + + if (pcipcwd_private.boot_status == 0) + printk(KERN_INFO PFX "No previous trip detected - Cold boot or reset\n"); +} + static int pcipcwd_start(void) { int stat_reg; @@ -161,7 +221,7 @@ static int pcipcwd_start(void) stat_reg = inb_p(pcipcwd_private.io_addr + 2); spin_unlock(&pcipcwd_private.io_lock); - if (stat_reg & 0x10) { + if (stat_reg & WD_PCI_WDIS) { printk(KERN_ERR PFX "Card timer not enabled\n"); return -1; } @@ -183,7 +243,7 @@ static int pcipcwd_stop(void) stat_reg = inb_p(pcipcwd_private.io_addr + 2); spin_unlock(&pcipcwd_private.io_lock); - if (!(stat_reg & 0x10)) { + if (!(stat_reg & WD_PCI_WDIS)) { printk(KERN_ERR PFX "Card did not acknowledge disable attempt\n"); return -1; } @@ -194,7 +254,7 @@ static int pcipcwd_stop(void) static int pcipcwd_keepalive(void) { /* Re-trigger watchdog by writing to port 0 */ - outb_p(0x42, pcipcwd_private.io_addr); + outb_p(0x42, pcipcwd_private.io_addr); /* send out any data */ return 0; } @@ -215,13 +275,13 @@ static int pcipcwd_set_heartbeat(int t) static int pcipcwd_get_status(int *status) { - int new_status; + int control_status; *status=0; - new_status = inb_p(pcipcwd_private.io_addr + 1); - if (new_status & WD_PCI_WTRP) + control_status = inb_p(pcipcwd_private.io_addr + 1); + if (control_status & WD_PCI_WTRP) *status |= WDIOF_CARDRESET; - if (new_status & WD_PCI_TTRP) { + if (control_status & WD_PCI_TTRP) { *status |= WDIOF_OVERHEAT; if (temp_panic) panic(PFX "Temperature overheat trip!\n"); @@ -232,7 +292,20 @@ static int pcipcwd_get_status(int *status) static int pcipcwd_clear_status(void) { - outb_p(0x01, pcipcwd_private.io_addr + 1); + int control_status; + int msb; + int reset_counter; + + control_status = inb_p(pcipcwd_private.io_addr + 1); + + /* clear trip status & LED and keep mode of relay 2 */ + outb_p((control_status & WD_PCI_R2DS) | WD_PCI_WTRP, pcipcwd_private.io_addr + 1); + + /* clear reset counter */ + msb=0; + reset_counter=0xff; + send_command(CMD_GET_CLEAR_RESET_COUNT, &msb, &reset_counter); + return 0; } @@ -242,11 +315,13 @@ static int pcipcwd_get_temperature(int *temperature) if (!pcipcwd_private.supports_temp) return -ENODEV; + *temperature = inb_p(pcipcwd_private.io_addr); + /* * Convert celsius to fahrenheit, since this was * the decided 'standard' for this return value. */ - *temperature = ((inb_p(pcipcwd_private.io_addr)) * 9 / 5) + 32; + *temperature = (*temperature * 9 / 5) + 32; return 0; } @@ -256,7 +331,7 @@ static int pcipcwd_get_temperature(int *temperature) */ static ssize_t pcipcwd_write(struct file *file, const char __user *data, - size_t len, loff_t *ppos) + size_t len, loff_t *ppos) { /* See if we got the magic character 'V' and reload the timer */ if (len) { @@ -381,8 +456,9 @@ static int pcipcwd_ioctl(struct inode *inode, struct file *file, static int pcipcwd_open(struct inode *inode, struct file *file) { /* /dev/watchdog can only be opened once */ - if (test_and_set_bit(0, &is_active)) + if (test_and_set_bit(0, &is_active)) { return -EBUSY; + } /* Activate */ pcipcwd_start(); @@ -492,19 +568,10 @@ static struct notifier_block pcipcwd_notifier = { * Init & exit routines */ -static inline void check_temperature_support(void) -{ - if (inb_p(pcipcwd_private.io_addr) != 0xF0) - pcipcwd_private.supports_temp = 1; -} - static int __devinit pcipcwd_card_init(struct pci_dev *pdev, const struct pci_device_id *ent) { int ret = -EIO; - int got_fw_rev, fw_rev_major, fw_rev_minor; - char fw_ver_str[20]; - char option_switches; cards_found++; if (cards_found == 1) @@ -546,36 +613,10 @@ static int __devinit pcipcwd_card_init(struct pci_dev *pdev, pcipcwd_stop(); /* Check whether or not the card supports the temperature device */ - check_temperature_support(); - - /* Get the Firmware Version */ - got_fw_rev = send_command(CMD_GET_FIRMWARE_VERSION, &fw_rev_major, &fw_rev_minor); - if (got_fw_rev) { - sprintf(fw_ver_str, "%u.%02u", fw_rev_major, fw_rev_minor); - } else { - sprintf(fw_ver_str, "<card no answer>"); - } + pcipcwd_check_temperature_support(); - /* Get switch settings */ - option_switches = inb_p(pcipcwd_private.io_addr + 3); - - printk(KERN_INFO PFX "Found card at port 0x%04x (Firmware: %s) %s temp option\n", - (int) pcipcwd_private.io_addr, fw_ver_str, - (pcipcwd_private.supports_temp ? "with" : "without")); - - printk(KERN_INFO PFX "Option switches (0x%02x): Temperature Reset Enable=%s, Power On Delay=%s\n", - option_switches, - ((option_switches & 0x10) ? "ON" : "OFF"), - ((option_switches & 0x08) ? "ON" : "OFF")); - - if (pcipcwd_private.boot_status & WDIOF_CARDRESET) - printk(KERN_INFO PFX "Previous reset was caused by the Watchdog card\n"); - - if (pcipcwd_private.boot_status & WDIOF_OVERHEAT) - printk(KERN_INFO PFX "Card sensed a CPU Overheat\n"); - - if (pcipcwd_private.boot_status == 0) - printk(KERN_INFO PFX "No previous trip detected - Cold boot or reset\n"); + /* Show info about the card itself */ + pcipcwd_show_card_info(); /* Check that the heartbeat value is within it's range ; if not reset to the default */ if (pcipcwd_set_heartbeat(heartbeat)) { @@ -656,7 +697,7 @@ static struct pci_driver pcipcwd_driver = { static int __init pcipcwd_init_module(void) { - spin_lock_init (&pcipcwd_private.io_lock); + spin_lock_init(&pcipcwd_private.io_lock); return pci_register_driver(&pcipcwd_driver); } |
