summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--drivers/serial/sunzilog.c138
-rw-r--r--drivers/serial/sunzilog.h19
2 files changed, 122 insertions, 35 deletions
diff --git a/drivers/serial/sunzilog.c b/drivers/serial/sunzilog.c
index da73205..0985193 100644
--- a/drivers/serial/sunzilog.c
+++ b/drivers/serial/sunzilog.c
@@ -92,6 +92,8 @@ struct uart_sunzilog_port {
#define SUNZILOG_FLAG_REGS_HELD 0x00000040
#define SUNZILOG_FLAG_TX_STOPPED 0x00000080
#define SUNZILOG_FLAG_TX_ACTIVE 0x00000100
+#define SUNZILOG_FLAG_ESCC 0x00000200
+#define SUNZILOG_FLAG_ISR_HANDLER 0x00000400
unsigned int cflag;
@@ -174,9 +176,11 @@ static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel)
/* This function must only be called when the TX is not busy. The UART
* port lock must be held and local interrupts disabled.
*/
-static void __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
+static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
{
int i;
+ int escc;
+ unsigned char r15;
/* Let pending transmits finish. */
for (i = 0; i < 1000; i++) {
@@ -229,11 +233,25 @@ static void __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *
write_zsreg(channel, R14, regs[R14]);
/* External status interrupt control. */
- write_zsreg(channel, R15, regs[R15]);
+ write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN);
+
+ /* ESCC Extension Register */
+ r15 = read_zsreg(channel, R15);
+ if (r15 & 0x01) {
+ write_zsreg(channel, R7, regs[R7p]);
+
+ /* External status interrupt and FIFO control. */
+ write_zsreg(channel, R15, regs[R15] & ~WR7pEN);
+ escc = 1;
+ } else {
+ /* Clear FIFO bit case it is an issue */
+ regs[R15] &= ~FIFOEN;
+ escc = 0;
+ }
/* Reset external status interrupts. */
- write_zsreg(channel, R0, RES_EXT_INT);
- write_zsreg(channel, R0, RES_EXT_INT);
+ write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */
+ write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */
/* Rewrite R3/R5, this time without enables masked. */
write_zsreg(channel, R3, regs[R3]);
@@ -241,6 +259,8 @@ static void __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *
/* Rewrite R1, this time without IRQ enabled masked. */
write_zsreg(channel, R1, regs[R1]);
+
+ return escc;
}
/* Reprogram the Zilog channel HW registers with the copies found in the
@@ -731,7 +751,7 @@ static void sunzilog_enable_ms(struct uart_port *port)
up->curregs[R15] = new_reg;
/* NOTE: Not subject to 'transmitter active' rule. */
- write_zsreg(channel, R15, up->curregs[R15]);
+ write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN);
}
}
@@ -861,44 +881,44 @@ sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag,
up->curregs[R14] = BRSRC | BRENAB;
/* Character size, stop bits, and parity. */
- up->curregs[3] &= ~RxN_MASK;
- up->curregs[5] &= ~TxN_MASK;
+ up->curregs[R3] &= ~RxN_MASK;
+ up->curregs[R5] &= ~TxN_MASK;
switch (cflag & CSIZE) {
case CS5:
- up->curregs[3] |= Rx5;
- up->curregs[5] |= Tx5;
+ up->curregs[R3] |= Rx5;
+ up->curregs[R5] |= Tx5;
up->parity_mask = 0x1f;
break;
case CS6:
- up->curregs[3] |= Rx6;
- up->curregs[5] |= Tx6;
+ up->curregs[R3] |= Rx6;
+ up->curregs[R5] |= Tx6;
up->parity_mask = 0x3f;
break;
case CS7:
- up->curregs[3] |= Rx7;
- up->curregs[5] |= Tx7;
+ up->curregs[R3] |= Rx7;
+ up->curregs[R5] |= Tx7;
up->parity_mask = 0x7f;
break;
case CS8:
default:
- up->curregs[3] |= Rx8;
- up->curregs[5] |= Tx8;
+ up->curregs[R3] |= Rx8;
+ up->curregs[R5] |= Tx8;
up->parity_mask = 0xff;
break;
};
- up->curregs[4] &= ~0x0c;
+ up->curregs[R4] &= ~0x0c;
if (cflag & CSTOPB)
- up->curregs[4] |= SB2;
+ up->curregs[R4] |= SB2;
else
- up->curregs[4] |= SB1;
+ up->curregs[R4] |= SB1;
if (cflag & PARENB)
- up->curregs[4] |= PAR_ENAB;
+ up->curregs[R4] |= PAR_ENAB;
else
- up->curregs[4] &= ~PAR_ENAB;
+ up->curregs[R4] &= ~PAR_ENAB;
if (!(cflag & PARODD))
- up->curregs[4] |= PAR_EVEN;
+ up->curregs[R4] |= PAR_EVEN;
else
- up->curregs[4] &= ~PAR_EVEN;
+ up->curregs[R4] &= ~PAR_EVEN;
up->port.read_status_mask = Rx_OVR;
if (iflag & INPCK)
@@ -952,7 +972,9 @@ sunzilog_set_termios(struct uart_port *port, struct ktermios *termios,
static const char *sunzilog_type(struct uart_port *port)
{
- return "zs";
+ struct uart_sunzilog_port *up = UART_ZILOG(port);
+
+ return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs";
}
/* We do not request/release mappings of the registers here, this
@@ -1170,7 +1192,7 @@ static int __init sunzilog_console_setup(struct console *con, char *options)
spin_lock_irqsave(&up->port.lock, flags);
- up->curregs[R15] = BRKIE;
+ up->curregs[R15] |= BRKIE;
sunzilog_convert_to_zs(up, con->cflag, 0, brg);
sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
@@ -1229,7 +1251,7 @@ static void __init sunzilog_init_kbdms(struct uart_sunzilog_port *up, int channe
baud = 4800;
}
- up->curregs[R15] = BRKIE;
+ up->curregs[R15] |= BRKIE;
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
sunzilog_convert_to_zs(up, up->cflag, 0, brg);
sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
@@ -1283,8 +1305,18 @@ static void __devinit sunzilog_init_hw(struct uart_sunzilog_port *up)
if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
SUNZILOG_FLAG_CONS_MOUSE)) {
+ up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
+ up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
+ up->curregs[R3] = RxENAB | Rx8;
+ up->curregs[R5] = TxENAB | Tx8;
+ up->curregs[R6] = 0x00; /* SDLC Address */
+ up->curregs[R7] = 0x7E; /* SDLC Flag */
+ up->curregs[R9] = NV;
+ up->curregs[R7p] = 0x00;
sunzilog_init_kbdms(up, up->port.line);
- up->curregs[R9] |= (NV | MIE);
+ /* Only enable interrupts if an ISR handler available */
+ if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
+ up->curregs[R9] |= MIE;
write_zsreg(channel, R9, up->curregs[R9]);
} else {
/* Normal serial TTY. */
@@ -1293,7 +1325,9 @@ static void __devinit sunzilog_init_hw(struct uart_sunzilog_port *up)
up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
up->curregs[R3] = RxENAB | Rx8;
up->curregs[R5] = TxENAB | Tx8;
- up->curregs[R9] = NV | MIE;
+ up->curregs[R6] = 0x00; /* SDLC Address */
+ up->curregs[R7] = 0x7E; /* SDLC Flag */
+ up->curregs[R9] = NV;
up->curregs[R10] = NRZ;
up->curregs[R11] = TCBR | RCBR;
baud = 9600;
@@ -1301,7 +1335,14 @@ static void __devinit sunzilog_init_hw(struct uart_sunzilog_port *up)
up->curregs[R12] = (brg & 0xff);
up->curregs[R13] = (brg >> 8) & 0xff;
up->curregs[R14] = BRSRC | BRENAB;
- __load_zsregs(channel, up->curregs);
+ up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */
+ up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL;
+ if (__load_zsregs(channel, up->curregs)) {
+ up->flags |= SUNZILOG_FLAG_ESCC;
+ }
+ /* Only enable interrupts if an ISR handler available */
+ if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
+ up->curregs[R9] |= MIE;
write_zsreg(channel, R9, up->curregs[R9]);
}
@@ -1390,12 +1431,14 @@ static int __devinit zs_probe(struct of_device *op, const struct of_device_id *m
return err;
}
} else {
- printk(KERN_INFO "%s: Keyboard at MMIO %lx (irq = %d) "
- "is a zs\n",
- op->dev.bus_id, up[0].port.mapbase, op->irqs[0]);
- printk(KERN_INFO "%s: Mouse at MMIO %lx (irq = %d) "
- "is a zs\n",
- op->dev.bus_id, up[1].port.mapbase, op->irqs[0]);
+ printk(KERN_INFO "%s: Keyboard at MMIO 0x%lx (irq = %d) "
+ "is a %s\n",
+ op->dev.bus_id, up[0].port.mapbase, op->irqs[0],
+ sunzilog_type (&up[0].port));
+ printk(KERN_INFO "%s: Mouse at MMIO 0x%lx (irq = %d) "
+ "is a %s\n",
+ op->dev.bus_id, up[1].port.mapbase, op->irqs[0],
+ sunzilog_type (&up[1].port));
}
dev_set_drvdata(&op->dev, &up[0]);
@@ -1487,10 +1530,23 @@ static int __init sunzilog_init(void)
goto out_unregister_uart;
if (zilog_irq != -1) {
+ struct uart_sunzilog_port *up = sunzilog_irq_chain;
err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
"zs", sunzilog_irq_chain);
if (err)
goto out_unregister_driver;
+
+ /* Enable Interrupts */
+ while (up) {
+ struct zilog_channel __iomem *channel;
+
+ /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
+ channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
+ up->flags |= SUNZILOG_FLAG_ISR_HANDLER;
+ up->curregs[R9] |= MIE;
+ write_zsreg(channel, R9, up->curregs[R9]);
+ up = up->next;
+ }
}
out:
@@ -1515,6 +1571,20 @@ static void __exit sunzilog_exit(void)
of_unregister_driver(&zs_driver);
if (zilog_irq != -1) {
+ struct uart_sunzilog_port *up = sunzilog_irq_chain;
+
+ /* Disable Interrupts */
+ while (up) {
+ struct zilog_channel __iomem *channel;
+
+ /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
+ channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
+ up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER;
+ up->curregs[R9] &= ~MIE;
+ write_zsreg(channel, R9, up->curregs[R9]);
+ up = up->next;
+ }
+
free_irq(zilog_irq, sunzilog_irq_chain);
zilog_irq = -1;
}
diff --git a/drivers/serial/sunzilog.h b/drivers/serial/sunzilog.h
index 7939b6d..5dec7b4 100644
--- a/drivers/serial/sunzilog.h
+++ b/drivers/serial/sunzilog.h
@@ -13,7 +13,8 @@ struct zilog_layout {
struct zilog_channel channelA;
};
-#define NUM_ZSREGS 16
+#define NUM_ZSREGS 17
+#define R7p 16 /* Written as R7 with P15 bit 0 set */
/* Conversion routines to/from brg time constants from/to bits
* per second.
@@ -127,6 +128,15 @@ struct zilog_layout {
/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+/* Write Register 7' (ESCC Only) */
+#define AUTO_TxFLAG 1 /* Automatic Tx SDLC Flag */
+#define AUTO_EOM_RST 2 /* Automatic EOM Reset */
+#define AUTOnRTS 4 /* Automatic /RTS pin deactivation */
+#define RxFIFO_LVL 8 /* Receive FIFO interrupt level */
+#define nDTRnREQ 0x10 /* /DTR/REQ timing */
+#define TxFIFO_LVL 0x20 /* Transmit FIFO interrupt level */
+#define EXT_RD_EN 0x40 /* Extended read register enable */
+
/* Write Register 8 (transmit buffer) */
/* Write Register 9 (Master interrupt control) */
@@ -135,6 +145,7 @@ struct zilog_layout {
#define DLC 4 /* Disable Lower Chain */
#define MIE 8 /* Master Interrupt Enable */
#define STATHI 0x10 /* Status high */
+#define SWIACK 0x20 /* Software Interrupt Ack (not on NMOS) */
#define NORESET 0 /* No reset on write to R9 */
#define CHRB 0x40 /* Reset channel B */
#define CHRA 0x80 /* Reset channel A */
@@ -187,7 +198,9 @@ struct zilog_layout {
#define SNRZI 0xe0 /* Set NRZI mode */
/* Write Register 15 (external/status interrupt control) */
+#define WR7pEN 1 /* WR7' Enable (ESCC only) */
#define ZCIE 2 /* Zero count IE */
+#define FIFOEN 4 /* FIFO Enable (ESCC only) */
#define DCDIE 8 /* DCD IE */
#define SYNCIE 0x10 /* Sync/hunt IE */
#define CTSIE 0x20 /* CTS IE */
@@ -241,6 +254,10 @@ struct zilog_layout {
#define CHATxIP 0x10 /* Channel A Tx IP */
#define CHARxIP 0x20 /* Channel A Rx IP */
+/* Read Register 6 (LSB frame byte count [Not on NMOS]) */
+
+/* Read Register 7 (MSB frame byte count and FIFO status [Not on NMOS]) */
+
/* Read Register 8 (receive data register) */
/* Read Register 10 (misc status bits) */
OpenPOWER on IntegriCloud