diff options
76 files changed, 1688 insertions, 1043 deletions
diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt deleted file mode 100644 index 3545ea7..0000000 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ /dev/null @@ -1,46 +0,0 @@ -* Texas Instruments Davinci NAND - -This file provides information, what the device node for the -davinci nand interface contain. - -Required properties: -- compatible: "ti,davinci-nand"; -- reg : contain 2 offset/length values: - - offset and length for the access window - - offset and length for accessing the aemif control registers -- ti,davinci-chipselect: Indicates on the davinci_nand driver which - chipselect is used for accessing the nand. - -Recommended properties : -- ti,davinci-mask-ale: mask for ale -- ti,davinci-mask-cle: mask for cle -- ti,davinci-mask-chipsel: mask for chipselect -- ti,davinci-ecc-mode: ECC mode valid values for davinci driver: - - "none" - - "soft" - - "hw" -- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. -- ti,davinci-nand-buswidth: buswidth 8 or 16 -- ti,davinci-nand-use-bbt: use flash based bad block table support. - -nand device bindings may contain additional sub-nodes describing -partitions of the address space. See partition.txt for more detail. - -Example(da850 EVM ): -nand_cs3@62000000 { - compatible = "ti,davinci-nand"; - reg = <0x62000000 0x807ff - 0x68000000 0x8000>; - ti,davinci-chipselect = <1>; - ti,davinci-mask-ale = <0>; - ti,davinci-mask-cle = <0>; - ti,davinci-mask-chipsel = <0>; - ti,davinci-ecc-mode = "hw"; - ti,davinci-ecc-bits = <4>; - ti,davinci-nand-use-bbt; - - partition@180000 { - label = "ubifs"; - reg = <0x180000 0x7e80000>; - }; -}; diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt new file mode 100644 index 0000000..cfb18ab --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt @@ -0,0 +1,94 @@ +Device tree bindings for Texas instruments Davinci/Keystone NAND controller + +This file provides information, what the device node for the davinci/keystone +NAND interface contains. + +Documentation: +Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf +Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf + +Required properties: + +- compatible: "ti,davinci-nand" + "ti,keystone-nand" + +- reg: Contains 2 offset/length values: + - offset and length for the access window. + - offset and length for accessing the AEMIF + control registers. + +- ti,davinci-chipselect: number of chipselect. Indicates on the + davinci_nand driver which chipselect is used + for accessing the nand. + Can be in the range [0-3]. + +Recommended properties : + +- ti,davinci-mask-ale: mask for ALE. Needed for executing address + phase. These offset will be added to the base + address for the chip select space the NAND Flash + device is connected to. + If not set equal to 0x08. + +- ti,davinci-mask-cle: mask for CLE. Needed for executing command + phase. These offset will be added to the base + address for the chip select space the NAND Flash + device is connected to. + If not set equal to 0x10. + +- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask + addresses for given chipselect. + +- nand-ecc-mode: operation mode of the NAND ecc mode. ECC mode + valid values for davinci driver: + - "none" + - "soft" + - "hw" + +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. + +- nand-bus-width: buswidth 8 or 16. If not present 8. + +- nand-on-flash-bbt: use flash based bad block table support. OOB + identifier is saved in OOB area. If not present + false. + +Deprecated properties: + +- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode + valid values for davinci driver: + - "none" + - "soft" + - "hw" + +- ti,davinci-nand-buswidth: buswidth 8 or 16. If not present 8. + +- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB + identifier is saved in OOB area. If not present + false. + +Nand device bindings may contain additional sub-nodes describing partitions of +the address space. See partition.txt for more detail. The NAND Flash timing +values must be programmed in the chip select’s node of AEMIF +memory-controller (see Documentation/devicetree/bindings/memory-controllers/ +davinci-aemif.txt). + +Example(da850 EVM ): + +nand_cs3@62000000 { + compatible = "ti,davinci-nand"; + reg = <0x62000000 0x807ff + 0x68000000 0x8000>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + nand-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + nand-on-flash-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index 551b2a1..458d596 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -17,6 +17,14 @@ Required properties: Optional properties: - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + - fsl,use-minimum-ecc: Protect this NAND flash with the minimum ECC + strength required. The required ECC strength is + automatically discoverable for some flash + (e.g., according to the ONFI standard). + However, note that if this strength is not + discoverable or this property is not enabled, + the software may chooses an implementation-defined + ECC scheme. The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt index f1421e2..86e0a56 100644 --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt @@ -2,7 +2,9 @@ PXA3xx NAND DT bindings Required properties: - - compatible: Should be "marvell,pxa3xx-nand" + - compatible: Should be set to one of the following: + marvell,pxa3xx-nand + marvell,armada370-nand - reg: The register base for the controller - interrupts: The interrupt to map - #address-cells: Set to <1> if the node includes partitions @@ -13,6 +15,8 @@ Optional properties: - marvell,nand-keep-config: Set to keep the NAND controller config as set by the bootloader - num-cs: Number of chipselect lines to usw + - nand-on-flash-bbt: boolean to enable on flash bbt option if + not present false Example: diff --git a/Documentation/mtd/nand/pxa3xx-nand.txt b/Documentation/mtd/nand/pxa3xx-nand.txt new file mode 100644 index 0000000..840fd41 --- /dev/null +++ b/Documentation/mtd/nand/pxa3xx-nand.txt @@ -0,0 +1,113 @@ + +About this document +=================== + +Some notes about Marvell's NAND controller available in PXA and Armada 370/XP +SoC (aka NFCv1 and NFCv2), with an emphasis on the latter. + +NFCv2 controller background +=========================== + +The controller has a 2176 bytes FIFO buffer. Therefore, in order to support +larger pages, I/O operations on 4 KiB and 8 KiB pages is done with a set of +chunked transfers. + +For instance, if we choose a 2048 data chunk and set "BCH" ECC (see below) +we'll have this layout in the pages: + + ------------------------------------------------------------------------------ + | 2048B data | 32B spare | 30B ECC || 2048B data | 32B spare | 30B ECC | ... | + ------------------------------------------------------------------------------ + +The driver reads the data and spare portions independently and builds an internal +buffer with this layout (in the 4 KiB page case): + + ------------------------------------------ + | 4096B data | 64B spare | + ------------------------------------------ + +Also, for the READOOB command the driver disables the ECC and reads a 'spare + ECC' +OOB, one per chunk read. + + ------------------------------------------------------------------- + | 4096B data | 32B spare | 30B ECC | 32B spare | 30B ECC | + ------------------------------------------------------------------- + +So, in order to achieve reading (for instance), we issue several READ0 commands +(with some additional controller-specific magic) and read two chunks of 2080B +(2048 data + 32 spare) each. +The driver accommodates this data to expose the NAND core a contiguous buffer +(4096 data + spare) or (4096 + spare + ECC + spare + ECC). + +ECC +=== + +The controller has built-in hardware ECC capabilities. In addition it is +configurable between two modes: 1) Hamming, 2) BCH. + +Note that the actual BCH mode: BCH-4 or BCH-8 will depend on the way +the controller is configured to transfer the data. + +In the BCH mode the ECC code will be calculated for each transfered chunk +and expected to be located (when reading/programming) right after the spare +bytes as the figure above shows. + +So, repeating the above scheme, a 2048B data chunk will be followed by 32B +spare, and then the ECC controller will read/write the ECC code (30B in +this case): + + ------------------------------------ + | 2048B data | 32B spare | 30B ECC | + ------------------------------------ + +If the ECC mode is 'BCH' then the ECC is *always* 30 bytes long. +If the ECC mode is 'Hamming' the ECC is 6 bytes long, for each 512B block. +So in Hamming mode, a 2048B page will have a 24B ECC. + +Despite all of the above, the controller requires the driver to only read or +write in multiples of 8-bytes, because the data buffer is 64-bits. + +OOB +=== + +Because of the above scheme, and because the "spare" OOB is really located in +the middle of a page, spare OOB cannot be read or write independently of the +data area. In other words, in order to read the OOB (aka READOOB), the entire +page (aka READ0) has to be read. + +In the same sense, in order to write to the spare OOB the driver has to write +an *entire* page. + +Factory bad blocks handling +=========================== + +Given the ECC BCH requires to layout the device's pages in a split +data/OOB/data/OOB way, the controller has a view of the flash page that's +different from the specified (aka the manufacturer's) view. In other words, + +Factory view: + + ----------------------------------------------- + | Data |x OOB | + ----------------------------------------------- + +Driver's view: + + ----------------------------------------------- + | Data | OOB | Data x | OOB | + ----------------------------------------------- + +It can be seen from the above, that the factory bad block marker must be +searched within the 'data' region, and not in the usual OOB region. + +In addition, this means under regular usage the driver will write such +position (since it belongs to the data region) and every used block is +likely to be marked as bad. + +For this reason, marking the block as bad in the OOB is explicitly +disabled by using the NAND_BBT_NO_OOB_BBM option in the driver. The rationale +for this is that there's no point in marking a block as bad, because good +blocks are also 'marked as bad' (in the OOB BBM sense) under normal usage. + +Instead, the driver relies on the bad block table alone, and should only perform +the bad block scan on the very first time (when the device hasn't been used). diff --git a/MAINTAINERS b/MAINTAINERS index 9bf651c..6d73831c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -5622,10 +5622,11 @@ F: mm/page_cgroup.c MEMORY TECHNOLOGY DEVICES (MTD) M: David Woodhouse <dwmw2@infradead.org> +M: Brian Norris <computersforpeace@gmail.com> L: linux-mtd@lists.infradead.org W: http://www.linux-mtd.infradead.org/ Q: http://patchwork.ozlabs.org/project/linux-mtd/list/ -T: git git://git.infradead.org/mtd-2.6.git +T: git git://git.infradead.org/linux-mtd.git S: Maintained F: drivers/mtd/ F: include/linux/mtd/ @@ -6942,6 +6943,12 @@ F: include/sound/pxa2xx-lib.h F: sound/arm/pxa* F: sound/soc/pxa/ +PXA3xx NAND FLASH DRIVER +M: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> +L: linux-mtd@lists.infradead.org +S: Maintained +F: drivers/mtd/nand/pxa3xx-nand.c + MMP SUPPORT M: Eric Miao <eric.y.miao@gmail.com> M: Haojian Zhuang <haojian.zhuang@gmail.com> diff --git a/arch/arm/plat-samsung/include/plat/regs-nand.h b/arch/arm/plat-samsung/include/plat/regs-nand.h deleted file mode 100644 index 238efea..0000000 --- a/arch/arm/plat-samsung/include/plat/regs-nand.h +++ /dev/null @@ -1,123 +0,0 @@ -/* arch/arm/mach-s3c2410/include/mach/regs-nand.h - * - * Copyright (c) 2004-2005 Simtec Electronics <linux@simtec.co.uk> - * http://www.simtec.co.uk/products/SWLINUX/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * S3C2410 NAND register definitions -*/ - -#ifndef __ASM_ARM_REGS_NAND -#define __ASM_ARM_REGS_NAND - - -#define S3C2410_NFREG(x) (x) - -#define S3C2410_NFCONF S3C2410_NFREG(0x00) -#define S3C2410_NFCMD S3C2410_NFREG(0x04) -#define S3C2410_NFADDR S3C2410_NFREG(0x08) -#define S3C2410_NFDATA S3C2410_NFREG(0x0C) -#define S3C2410_NFSTAT S3C2410_NFREG(0x10) -#define S3C2410_NFECC S3C2410_NFREG(0x14) - -#define S3C2440_NFCONT S3C2410_NFREG(0x04) -#define S3C2440_NFCMD S3C2410_NFREG(0x08) -#define S3C2440_NFADDR S3C2410_NFREG(0x0C) -#define S3C2440_NFDATA S3C2410_NFREG(0x10) -#define S3C2440_NFECCD0 S3C2410_NFREG(0x14) -#define S3C2440_NFECCD1 S3C2410_NFREG(0x18) -#define S3C2440_NFECCD S3C2410_NFREG(0x1C) -#define S3C2440_NFSTAT S3C2410_NFREG(0x20) -#define S3C2440_NFESTAT0 S3C2410_NFREG(0x24) -#define S3C2440_NFESTAT1 S3C2410_NFREG(0x28) -#define S3C2440_NFMECC0 S3C2410_NFREG(0x2C) -#define S3C2440_NFMECC1 S3C2410_NFREG(0x30) -#define S3C2440_NFSECC S3C2410_NFREG(0x34) -#define S3C2440_NFSBLK S3C2410_NFREG(0x38) -#define S3C2440_NFEBLK S3C2410_NFREG(0x3C) - -#define S3C2412_NFSBLK S3C2410_NFREG(0x20) -#define S3C2412_NFEBLK S3C2410_NFREG(0x24) -#define S3C2412_NFSTAT S3C2410_NFREG(0x28) -#define S3C2412_NFMECC_ERR0 S3C2410_NFREG(0x2C) -#define S3C2412_NFMECC_ERR1 S3C2410_NFREG(0x30) -#define S3C2412_NFMECC0 S3C2410_NFREG(0x34) -#define S3C2412_NFMECC1 S3C2410_NFREG(0x38) -#define S3C2412_NFSECC S3C2410_NFREG(0x3C) - -#define S3C2410_NFCONF_EN (1<<15) -#define S3C2410_NFCONF_512BYTE (1<<14) -#define S3C2410_NFCONF_4STEP (1<<13) -#define S3C2410_NFCONF_INITECC (1<<12) -#define S3C2410_NFCONF_nFCE (1<<11) -#define S3C2410_NFCONF_TACLS(x) ((x)<<8) -#define S3C2410_NFCONF_TWRPH0(x) ((x)<<4) -#define S3C2410_NFCONF_TWRPH1(x) ((x)<<0) - -#define S3C2410_NFSTAT_BUSY (1<<0) - -#define S3C2440_NFCONF_BUSWIDTH_8 (0<<0) -#define S3C2440_NFCONF_BUSWIDTH_16 (1<<0) -#define S3C2440_NFCONF_ADVFLASH (1<<3) -#define S3C2440_NFCONF_TACLS(x) ((x)<<12) -#define S3C2440_NFCONF_TWRPH0(x) ((x)<<8) -#define S3C2440_NFCONF_TWRPH1(x) ((x)<<4) - -#define S3C2440_NFCONT_LOCKTIGHT (1<<13) -#define S3C2440_NFCONT_SOFTLOCK (1<<12) -#define S3C2440_NFCONT_ILLEGALACC_EN (1<<10) -#define S3C2440_NFCONT_RNBINT_EN (1<<9) -#define S3C2440_NFCONT_RN_FALLING (1<<8) -#define S3C2440_NFCONT_SPARE_ECCLOCK (1<<6) -#define S3C2440_NFCONT_MAIN_ECCLOCK (1<<5) -#define S3C2440_NFCONT_INITECC (1<<4) -#define S3C2440_NFCONT_nFCE (1<<1) -#define S3C2440_NFCONT_ENABLE (1<<0) - -#define S3C2440_NFSTAT_READY (1<<0) -#define S3C2440_NFSTAT_nCE (1<<1) -#define S3C2440_NFSTAT_RnB_CHANGE (1<<2) -#define S3C2440_NFSTAT_ILLEGAL_ACCESS (1<<3) - -#define S3C2412_NFCONF_NANDBOOT (1<<31) -#define S3C2412_NFCONF_ECCCLKCON (1<<30) -#define S3C2412_NFCONF_ECC_MLC (1<<24) -#define S3C2412_NFCONF_TACLS_MASK (7<<12) /* 1 extra bit of Tacls */ - -#define S3C2412_NFCONT_ECC4_DIRWR (1<<18) -#define S3C2412_NFCONT_LOCKTIGHT (1<<17) -#define S3C2412_NFCONT_SOFTLOCK (1<<16) -#define S3C2412_NFCONT_ECC4_ENCINT (1<<13) -#define S3C2412_NFCONT_ECC4_DECINT (1<<12) -#define S3C2412_NFCONT_MAIN_ECC_LOCK (1<<7) -#define S3C2412_NFCONT_INIT_MAIN_ECC (1<<5) -#define S3C2412_NFCONT_nFCE1 (1<<2) -#define S3C2412_NFCONT_nFCE0 (1<<1) - -#define S3C2412_NFSTAT_ECC_ENCDONE (1<<7) -#define S3C2412_NFSTAT_ECC_DECDONE (1<<6) -#define S3C2412_NFSTAT_ILLEGAL_ACCESS (1<<5) -#define S3C2412_NFSTAT_RnB_CHANGE (1<<4) -#define S3C2412_NFSTAT_nFCE1 (1<<3) -#define S3C2412_NFSTAT_nFCE0 (1<<2) -#define S3C2412_NFSTAT_Res1 (1<<1) -#define S3C2412_NFSTAT_READY (1<<0) - -#define S3C2412_NFECCERR_SERRDATA(x) (((x) >> 21) & 0xf) -#define S3C2412_NFECCERR_SERRBIT(x) (((x) >> 18) & 0x7) -#define S3C2412_NFECCERR_MERRDATA(x) (((x) >> 7) & 0x3ff) -#define S3C2412_NFECCERR_MERRBIT(x) (((x) >> 4) & 0x7) -#define S3C2412_NFECCERR_SPARE_ERR(x) (((x) >> 2) & 0x3) -#define S3C2412_NFECCERR_MAIN_ERR(x) (((x) >> 2) & 0x3) -#define S3C2412_NFECCERR_NONE (0) -#define S3C2412_NFECCERR_1BIT (1) -#define S3C2412_NFECCERR_MULTIBIT (2) -#define S3C2412_NFECCERR_ECCAREA (3) - - - -#endif /* __ASM_ARM_REGS_NAND */ - diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig index 5fab4e6e..5ebcda3 100644 --- a/drivers/mtd/Kconfig +++ b/drivers/mtd/Kconfig @@ -157,10 +157,11 @@ config MTD_BCM47XX_PARTS comment "User Modules And Translation Layers" +# +# MTD block device support is select'ed if needed +# config MTD_BLKDEVS - tristate "Common interface to block layer for MTD 'translation layers'" - depends on BLOCK - default n + tristate config MTD_BLOCK tristate "Caching block device access to MTD devices" diff --git a/drivers/mtd/afs.c b/drivers/mtd/afs.c index 5a3942b..96a33e3f 100644 --- a/drivers/mtd/afs.c +++ b/drivers/mtd/afs.c @@ -264,7 +264,8 @@ static struct mtd_part_parser afs_parser = { static int __init afs_parser_init(void) { - return register_mtd_parser(&afs_parser); + register_mtd_parser(&afs_parser); + return 0; } static void __exit afs_parser_exit(void) diff --git a/drivers/mtd/ar7part.c b/drivers/mtd/ar7part.c index ddc0a42..7c9172a 100644 --- a/drivers/mtd/ar7part.c +++ b/drivers/mtd/ar7part.c @@ -139,7 +139,8 @@ static struct mtd_part_parser ar7_parser = { static int __init ar7_parser_init(void) { - return register_mtd_parser(&ar7_parser); + register_mtd_parser(&ar7_parser); + return 0; } static void __exit ar7_parser_exit(void) diff --git a/drivers/mtd/bcm47xxpart.c b/drivers/mtd/bcm47xxpart.c index 7a6384b..de1eb92 100644 --- a/drivers/mtd/bcm47xxpart.c +++ b/drivers/mtd/bcm47xxpart.c @@ -23,10 +23,12 @@ * Amount of bytes we read when analyzing each block of flash memory. * Set it big enough to allow detecting partition and reading important data. */ -#define BCM47XXPART_BYTES_TO_READ 0x404 +#define BCM47XXPART_BYTES_TO_READ 0x4e8 /* Magics */ #define BOARD_DATA_MAGIC 0x5246504D /* MPFR */ +#define BOARD_DATA_MAGIC2 0xBD0D0BBD +#define CFE_MAGIC 0x43464531 /* 1EFC */ #define FACTORY_MAGIC 0x59544346 /* FCTY */ #define POT_MAGIC1 0x54544f50 /* POTT */ #define POT_MAGIC2 0x504f /* OP */ @@ -102,8 +104,9 @@ static int bcm47xxpart_parse(struct mtd_info *master, continue; } - /* CFE has small NVRAM at 0x400 */ - if (buf[0x400 / 4] == NVRAM_HEADER) { + /* Magic or small NVRAM at 0x400 */ + if ((buf[0x4e0 / 4] == CFE_MAGIC && buf[0x4e4 / 4] == CFE_MAGIC) || + (buf[0x400 / 4] == NVRAM_HEADER)) { bcm47xxpart_add_part(&parts[curr_part++], "boot", offset, MTD_WRITEABLE); continue; @@ -190,6 +193,21 @@ static int bcm47xxpart_parse(struct mtd_info *master, offset, 0); continue; } + + /* Read middle of the block */ + if (mtd_read(master, offset + 0x8000, 0x4, + &bytes_read, (uint8_t *)buf) < 0) { + pr_err("mtd_read error while parsing (offset: 0x%X)!\n", + offset); + continue; + } + + /* Some devices (ex. WNDR3700v3) don't have a standard 'MPFR' */ + if (buf[0x000 / 4] == BOARD_DATA_MAGIC2) { + bcm47xxpart_add_part(&parts[curr_part++], "board_data", + offset, MTD_WRITEABLE); + continue; + } } /* Look for NVRAM at the end of the last block. */ @@ -243,7 +261,8 @@ static struct mtd_part_parser bcm47xxpart_mtd_parser = { static int __init bcm47xxpart_init(void) { - return register_mtd_parser(&bcm47xxpart_mtd_parser); + register_mtd_parser(&bcm47xxpart_mtd_parser); + return 0; } static void __exit bcm47xxpart_exit(void) diff --git a/drivers/mtd/bcm63xxpart.c b/drivers/mtd/bcm63xxpart.c index 5c81390..b2443f7 100644 --- a/drivers/mtd/bcm63xxpart.c +++ b/drivers/mtd/bcm63xxpart.c @@ -221,7 +221,8 @@ static struct mtd_part_parser bcm63xx_cfe_parser = { static int __init bcm63xx_cfe_parser_init(void) { - return register_mtd_parser(&bcm63xx_cfe_parser); + register_mtd_parser(&bcm63xx_cfe_parser); + return 0; } static void __exit bcm63xx_cfe_parser_exit(void) diff --git a/drivers/mtd/cmdlinepart.c b/drivers/mtd/cmdlinepart.c index 721caeb..3e829b3 100644 --- a/drivers/mtd/cmdlinepart.c +++ b/drivers/mtd/cmdlinepart.c @@ -395,7 +395,8 @@ static int __init cmdline_parser_init(void) { if (mtdparts) mtdpart_setup(mtdparts); - return register_mtd_parser(&cmdline_parser); + register_mtd_parser(&cmdline_parser); + return 0; } static void __exit cmdline_parser_exit(void) diff --git a/drivers/mtd/devices/docg3.c b/drivers/mtd/devices/docg3.c index 4f091c1..dd5e101 100644 --- a/drivers/mtd/devices/docg3.c +++ b/drivers/mtd/devices/docg3.c @@ -2047,21 +2047,21 @@ static int __init docg3_probe(struct platform_device *pdev) ress = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!ress) { dev_err(dev, "No I/O memory resource defined\n"); - goto noress; + return ret; } - base = ioremap(ress->start, DOC_IOSPACE_SIZE); + base = devm_ioremap(dev, ress->start, DOC_IOSPACE_SIZE); ret = -ENOMEM; - cascade = kzalloc(sizeof(*cascade) * DOC_MAX_NBFLOORS, - GFP_KERNEL); + cascade = devm_kzalloc(dev, sizeof(*cascade) * DOC_MAX_NBFLOORS, + GFP_KERNEL); if (!cascade) - goto nomem1; + return ret; cascade->base = base; mutex_init(&cascade->lock); cascade->bch = init_bch(DOC_ECC_BCH_M, DOC_ECC_BCH_T, DOC_ECC_BCH_PRIMPOLY); if (!cascade->bch) - goto nomem2; + return ret; for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) { mtd = doc_probe_device(cascade, floor, dev); @@ -2101,11 +2101,6 @@ err_probe: for (floor = 0; floor < DOC_MAX_NBFLOORS; floor++) if (cascade->floors[floor]) doc_release_device(cascade->floors[floor]); -nomem2: - kfree(cascade); -nomem1: - iounmap(base); -noress: return ret; } @@ -2119,7 +2114,6 @@ static int __exit docg3_release(struct platform_device *pdev) { struct docg3_cascade *cascade = platform_get_drvdata(pdev); struct docg3 *docg3 = cascade->floors[0]->priv; - void __iomem *base = cascade->base; int floor; doc_unregister_sysfs(pdev, cascade); @@ -2129,8 +2123,6 @@ static int __exit docg3_release(struct platform_device *pdev) doc_release_device(cascade->floors[floor]); free_bch(docg3->cascade->bch); - kfree(cascade); - iounmap(base); return 0; } diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c index 7eda71d..ad19139 100644 --- a/drivers/mtd/devices/m25p80.c +++ b/drivers/mtd/devices/m25p80.c @@ -41,6 +41,7 @@ #define OPCODE_WRSR 0x01 /* Write status register 1 byte */ #define OPCODE_NORM_READ 0x03 /* Read data bytes (low frequency) */ #define OPCODE_FAST_READ 0x0b /* Read data bytes (high frequency) */ +#define OPCODE_QUAD_READ 0x6b /* Read data bytes */ #define OPCODE_PP 0x02 /* Page program (up to 256 bytes) */ #define OPCODE_BE_4K 0x20 /* Erase 4KiB block */ #define OPCODE_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */ @@ -48,10 +49,12 @@ #define OPCODE_CHIP_ERASE 0xc7 /* Erase whole flash chip */ #define OPCODE_SE 0xd8 /* Sector erase (usually 64KiB) */ #define OPCODE_RDID 0x9f /* Read JEDEC ID */ +#define OPCODE_RDCR 0x35 /* Read configuration register */ /* 4-byte address opcodes - used on Spansion and some Macronix flashes. */ #define OPCODE_NORM_READ_4B 0x13 /* Read data bytes (low frequency) */ #define OPCODE_FAST_READ_4B 0x0c /* Read data bytes (high frequency) */ +#define OPCODE_QUAD_READ_4B 0x6c /* Read data bytes */ #define OPCODE_PP_4B 0x12 /* Page program (up to 256 bytes) */ #define OPCODE_SE_4B 0xdc /* Sector erase (usually 64KiB) */ @@ -76,6 +79,11 @@ #define SR_BP2 0x10 /* Block protect 2 */ #define SR_SRWD 0x80 /* SR write protect */ +#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */ + +/* Configuration Register bits. */ +#define CR_QUAD_EN_SPAN 0x2 /* Spansion Quad I/O */ + /* Define max times to check status register before we give up. */ #define MAX_READY_WAIT_JIFFIES (40 * HZ) /* M25P16 specs 40s max chip erase */ #define MAX_CMD_SIZE 6 @@ -84,6 +92,12 @@ /****************************************************************************/ +enum read_type { + M25P80_NORMAL = 0, + M25P80_FAST, + M25P80_QUAD, +}; + struct m25p { struct spi_device *spi; struct mutex lock; @@ -94,7 +108,7 @@ struct m25p { u8 read_opcode; u8 program_opcode; u8 *command; - bool fast_read; + enum read_type flash_read; }; static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd) @@ -131,6 +145,26 @@ static int read_sr(struct m25p *flash) } /* + * Read configuration register, returning its value in the + * location. Return the configuration register value. + * Returns negative if error occured. + */ +static int read_cr(struct m25p *flash) +{ + u8 code = OPCODE_RDCR; + int ret; + u8 val; + + ret = spi_write_then_read(flash->spi, &code, 1, &val, 1); + if (ret < 0) { + dev_err(&flash->spi->dev, "error %d reading CR\n", ret); + return ret; + } + + return val; +} + +/* * Write status register 1 byte * Returns negative if error occurred. */ @@ -220,6 +254,93 @@ static int wait_till_ready(struct m25p *flash) } /* + * Write status Register and configuration register with 2 bytes + * The first byte will be written to the status register, while the + * second byte will be written to the configuration register. + * Return negative if error occured. + */ +static int write_sr_cr(struct m25p *flash, u16 val) +{ + flash->command[0] = OPCODE_WRSR; + flash->command[1] = val & 0xff; + flash->command[2] = (val >> 8); + + return spi_write(flash->spi, flash->command, 3); +} + +static int macronix_quad_enable(struct m25p *flash) +{ + int ret, val; + u8 cmd[2]; + cmd[0] = OPCODE_WRSR; + + val = read_sr(flash); + cmd[1] = val | SR_QUAD_EN_MX; + write_enable(flash); + + spi_write(flash->spi, &cmd, 2); + + if (wait_till_ready(flash)) + return 1; + + ret = read_sr(flash); + if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) { + dev_err(&flash->spi->dev, "Macronix Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} + +static int spansion_quad_enable(struct m25p *flash) +{ + int ret; + int quad_en = CR_QUAD_EN_SPAN << 8; + + write_enable(flash); + + ret = write_sr_cr(flash, quad_en); + if (ret < 0) { + dev_err(&flash->spi->dev, + "error while writing configuration register\n"); + return -EINVAL; + } + + /* read back and check it */ + ret = read_cr(flash); + if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) { + dev_err(&flash->spi->dev, "Spansion Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} + +static int set_quad_mode(struct m25p *flash, u32 jedec_id) +{ + int status; + + switch (JEDEC_MFR(jedec_id)) { + case CFI_MFR_MACRONIX: + status = macronix_quad_enable(flash); + if (status) { + dev_err(&flash->spi->dev, + "Macronix quad-read not enabled\n"); + return -EINVAL; + } + return status; + default: + status = spansion_quad_enable(flash); + if (status) { + dev_err(&flash->spi->dev, + "Spansion quad-read not enabled\n"); + return -EINVAL; + } + return status; + } +} + +/* * Erase the whole flash memory * * Returns 0 if successful, non-zero otherwise. @@ -350,6 +471,35 @@ static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr) } /* + * Dummy Cycle calculation for different type of read. + * It can be used to support more commands with + * different dummy cycle requirements. + */ +static inline int m25p80_dummy_cycles_read(struct m25p *flash) +{ + switch (flash->flash_read) { + case M25P80_FAST: + case M25P80_QUAD: + return 1; + case M25P80_NORMAL: + return 0; + default: + dev_err(&flash->spi->dev, "No valid read type supported\n"); + return -1; + } +} + +static inline unsigned int m25p80_rx_nbits(const struct m25p *flash) +{ + switch (flash->flash_read) { + case M25P80_QUAD: + return 4; + default: + return 0; + } +} + +/* * Read an address range from the flash chip. The address range * may be any size provided it is within the physical boundaries. */ @@ -360,6 +510,7 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, struct spi_transfer t[2]; struct spi_message m; uint8_t opcode; + int dummy; pr_debug("%s: %s from 0x%08x, len %zd\n", dev_name(&flash->spi->dev), __func__, (u32)from, len); @@ -367,11 +518,18 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, spi_message_init(&m); memset(t, 0, (sizeof t)); + dummy = m25p80_dummy_cycles_read(flash); + if (dummy < 0) { + dev_err(&flash->spi->dev, "No valid read command supported\n"); + return -EINVAL; + } + t[0].tx_buf = flash->command; - t[0].len = m25p_cmdsz(flash) + (flash->fast_read ? 1 : 0); + t[0].len = m25p_cmdsz(flash) + dummy; spi_message_add_tail(&t[0], &m); t[1].rx_buf = buf; + t[1].rx_nbits = m25p80_rx_nbits(flash); t[1].len = len; spi_message_add_tail(&t[1], &m); @@ -391,8 +549,7 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, spi_sync(flash->spi, &m); - *retlen = m.actual_length - m25p_cmdsz(flash) - - (flash->fast_read ? 1 : 0); + *retlen = m.actual_length - m25p_cmdsz(flash) - dummy; mutex_unlock(&flash->lock); @@ -698,6 +855,7 @@ struct flash_info { #define SST_WRITE 0x04 /* use SST byte programming */ #define M25P_NO_FR 0x08 /* Can't do fastread */ #define SECT_4K_PMC 0x10 /* OPCODE_BE_4K_PMC works uniformly */ +#define M25P80_QUAD_READ 0x20 /* Flash supports Quad Read */ }; #define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \ @@ -775,7 +933,7 @@ static const struct spi_device_id m25p_ids[] = { { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) }, { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) }, - { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, 0) }, + { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, M25P80_QUAD_READ) }, /* Micron */ { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) }, @@ -795,8 +953,8 @@ static const struct spi_device_id m25p_ids[] = { { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, 0) }, { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, 0) }, { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) }, - { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, 0) }, - { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, 0) }, + { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, M25P80_QUAD_READ) }, + { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, M25P80_QUAD_READ) }, { "s70fl01gs", INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) }, { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) }, { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) }, @@ -851,6 +1009,7 @@ static const struct spi_device_id m25p_ids[] = { { "m25pe80", INFO(0x208014, 0, 64 * 1024, 16, 0) }, { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) }, + { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K) }, { "m25px32", INFO(0x207116, 0, 64 * 1024, 64, SECT_4K) }, { "m25px32-s0", INFO(0x207316, 0, 64 * 1024, 64, SECT_4K) }, { "m25px32-s1", INFO(0x206316, 0, 64 * 1024, 64, SECT_4K) }, @@ -937,6 +1096,7 @@ static int m25p_probe(struct spi_device *spi) unsigned i; struct mtd_part_parser_data ppdata; struct device_node *np = spi->dev.of_node; + int ret; /* Platform data helps sort out which chip type we have, as * well as how this board partitions it. If we don't have @@ -1051,22 +1211,46 @@ static int m25p_probe(struct spi_device *spi) flash->page_size = info->page_size; flash->mtd.writebufsize = flash->page_size; - if (np) + if (np) { /* If we were instantiated by DT, use it */ - flash->fast_read = of_property_read_bool(np, "m25p,fast-read"); - else + if (of_property_read_bool(np, "m25p,fast-read")) + flash->flash_read = M25P80_FAST; + else + flash->flash_read = M25P80_NORMAL; + } else { /* If we weren't instantiated by DT, default to fast-read */ - flash->fast_read = true; + flash->flash_read = M25P80_FAST; + } /* Some devices cannot do fast-read, no matter what DT tells us */ if (info->flags & M25P_NO_FR) - flash->fast_read = false; + flash->flash_read = M25P80_NORMAL; + + /* Quad-read mode takes precedence over fast/normal */ + if (spi->mode & SPI_RX_QUAD && info->flags & M25P80_QUAD_READ) { + ret = set_quad_mode(flash, info->jedec_id); + if (ret) { + dev_err(&flash->spi->dev, "quad mode not supported\n"); + return ret; + } + flash->flash_read = M25P80_QUAD; + } /* Default commands */ - if (flash->fast_read) + switch (flash->flash_read) { + case M25P80_QUAD: + flash->read_opcode = OPCODE_QUAD_READ; + break; + case M25P80_FAST: flash->read_opcode = OPCODE_FAST_READ; - else + break; + case M25P80_NORMAL: flash->read_opcode = OPCODE_NORM_READ; + break; + default: + dev_err(&flash->spi->dev, "No Read opcode defined\n"); + return -EINVAL; + } flash->program_opcode = OPCODE_PP; @@ -1077,9 +1261,17 @@ static int m25p_probe(struct spi_device *spi) flash->addr_width = 4; if (JEDEC_MFR(info->jedec_id) == CFI_MFR_AMD) { /* Dedicated 4-byte command set */ - flash->read_opcode = flash->fast_read ? - OPCODE_FAST_READ_4B : - OPCODE_NORM_READ_4B; + switch (flash->flash_read) { + case M25P80_QUAD: + flash->read_opcode = OPCODE_QUAD_READ_4B; + break; + case M25P80_FAST: + flash->read_opcode = OPCODE_FAST_READ_4B; + break; + case M25P80_NORMAL: + flash->read_opcode = OPCODE_NORM_READ_4B; + break; + } flash->program_opcode = OPCODE_PP_4B; /* No small sector erase for 4-byte command set */ flash->erase_opcode = OPCODE_SE_4B; diff --git a/drivers/mtd/devices/ms02-nv.c b/drivers/mtd/devices/ms02-nv.c index 182849d..5c8b322 100644 --- a/drivers/mtd/devices/ms02-nv.c +++ b/drivers/mtd/devices/ms02-nv.c @@ -205,7 +205,7 @@ static int __init ms02nv_init_one(ulong addr) mtd->type = MTD_RAM; mtd->flags = MTD_CAP_RAM; mtd->size = fixsize; - mtd->name = (char *)ms02nv_name; + mtd->name = ms02nv_name; mtd->owner = THIS_MODULE; mtd->_read = ms02nv_read; mtd->_write = ms02nv_write; diff --git a/drivers/mtd/devices/mtd_dataflash.c b/drivers/mtd/devices/mtd_dataflash.c index 4a47b02..624069d 100644 --- a/drivers/mtd/devices/mtd_dataflash.c +++ b/drivers/mtd/devices/mtd_dataflash.c @@ -669,7 +669,6 @@ static int add_dataflash_otp(struct spi_device *spi, char *name, int nr_pages, if (!err) return 0; - spi_set_drvdata(spi, NULL); kfree(priv); return err; } @@ -899,10 +898,8 @@ static int dataflash_remove(struct spi_device *spi) pr_debug("%s: remove\n", dev_name(&spi->dev)); status = mtd_device_unregister(&flash->mtd); - if (status == 0) { - spi_set_drvdata(spi, NULL); + if (status == 0) kfree(flash); - } return status; } diff --git a/drivers/mtd/devices/mtdram.c b/drivers/mtd/devices/mtdram.c index ec59d65..8e28508 100644 --- a/drivers/mtd/devices/mtdram.c +++ b/drivers/mtd/devices/mtdram.c @@ -92,7 +92,7 @@ static void __exit cleanup_mtdram(void) } int mtdram_init_device(struct mtd_info *mtd, void *mapped_address, - unsigned long size, char *name) + unsigned long size, const char *name) { memset(mtd, 0, sizeof(*mtd)); diff --git a/drivers/mtd/lpddr/lpddr_cmds.c b/drivers/mtd/lpddr/lpddr_cmds.c index 2ef19aa..d38b646 100644 --- a/drivers/mtd/lpddr/lpddr_cmds.c +++ b/drivers/mtd/lpddr/lpddr_cmds.c @@ -388,7 +388,7 @@ static void put_chip(struct map_info *map, struct flchip *chip) wake_up(&chip->wq); } -int do_write_buffer(struct map_info *map, struct flchip *chip, +static int do_write_buffer(struct map_info *map, struct flchip *chip, unsigned long adr, const struct kvec **pvec, unsigned long *pvec_seek, int len) { @@ -469,7 +469,7 @@ int do_write_buffer(struct map_info *map, struct flchip *chip, return ret; } -int do_erase_oneblock(struct mtd_info *mtd, loff_t adr) +static int do_erase_oneblock(struct mtd_info *mtd, loff_t adr) { struct map_info *map = mtd->priv; struct lpddr_private *lpddr = map->fldrv_priv; @@ -748,34 +748,6 @@ static int lpddr_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len) return do_xxlock(mtd, ofs, len, DO_XXLOCK_UNLOCK); } -int word_program(struct map_info *map, loff_t adr, uint32_t curval) -{ - int ret; - struct lpddr_private *lpddr = map->fldrv_priv; - int chipnum = adr >> lpddr->chipshift; - struct flchip *chip = &lpddr->chips[chipnum]; - - mutex_lock(&chip->mutex); - ret = get_chip(map, chip, FL_WRITING); - if (ret) { - mutex_unlock(&chip->mutex); - return ret; - } - - send_pfow_command(map, LPDDR_WORD_PROGRAM, adr, 0x00, (map_word *)&curval); - - ret = wait_for_ready(map, chip, (1<<lpddr->qinfo->SingleWordProgTime)); - if (ret) { - printk(KERN_WARNING"%s word_program error at: %llx; val: %x\n", - map->name, adr, curval); - goto out; - } - -out: put_chip(map, chip); - mutex_unlock(&chip->mutex); - return ret; -} - MODULE_LICENSE("GPL"); MODULE_AUTHOR("Alexey Korolev <akorolev@infradead.org>"); MODULE_DESCRIPTION("MTD driver for LPDDR flash chips"); diff --git a/drivers/mtd/maps/ixp4xx.c b/drivers/mtd/maps/ixp4xx.c index 10debfe..d6b2451 100644 --- a/drivers/mtd/maps/ixp4xx.c +++ b/drivers/mtd/maps/ixp4xx.c @@ -13,6 +13,7 @@ * */ +#include <linux/err.h> #include <linux/module.h> #include <linux/types.h> #include <linux/init.h> @@ -162,13 +163,6 @@ static int ixp4xx_flash_remove(struct platform_device *dev) mtd_device_unregister(info->mtd); map_destroy(info->mtd); } - if (info->map.virt) - iounmap(info->map.virt); - - if (info->res) { - release_resource(info->res); - kfree(info->res); - } if (plat->exit) plat->exit(); @@ -194,7 +188,8 @@ static int ixp4xx_flash_probe(struct platform_device *dev) return err; } - info = kzalloc(sizeof(struct ixp4xx_flash_info), GFP_KERNEL); + info = devm_kzalloc(&dev->dev, sizeof(struct ixp4xx_flash_info), + GFP_KERNEL); if(!info) { err = -ENOMEM; goto Error; @@ -220,20 +215,9 @@ static int ixp4xx_flash_probe(struct platform_device *dev) info->map.write = ixp4xx_probe_write16; info->map.copy_from = ixp4xx_copy_from; - info->res = request_mem_region(dev->resource->start, - resource_size(dev->resource), - "IXP4XXFlash"); - if (!info->res) { - printk(KERN_ERR "IXP4XXFlash: Could not reserve memory region\n"); - err = -ENOMEM; - goto Error; - } - - info->map.virt = ioremap(dev->resource->start, - resource_size(dev->resource)); - if (!info->map.virt) { - printk(KERN_ERR "IXP4XXFlash: Failed to ioremap region\n"); - err = -EIO; + info->map.virt = devm_ioremap_resource(&dev->dev, dev->resource); + if (IS_ERR(info->map.virt)) { + err = PTR_ERR(info->map.virt); goto Error; } diff --git a/drivers/mtd/maps/lantiq-flash.c b/drivers/mtd/maps/lantiq-flash.c index d7ac65d..93c507a 100644 --- a/drivers/mtd/maps/lantiq-flash.c +++ b/drivers/mtd/maps/lantiq-flash.c @@ -123,24 +123,28 @@ ltq_mtd_probe(struct platform_device *pdev) return -ENODEV; } - ltq_mtd = kzalloc(sizeof(struct ltq_mtd), GFP_KERNEL); + ltq_mtd = devm_kzalloc(&pdev->dev, sizeof(struct ltq_mtd), GFP_KERNEL); + if (!ltq_mtd) + return -ENOMEM; + platform_set_drvdata(pdev, ltq_mtd); ltq_mtd->res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!ltq_mtd->res) { dev_err(&pdev->dev, "failed to get memory resource\n"); - err = -ENOENT; - goto err_out; + return -ENOENT; } - ltq_mtd->map = kzalloc(sizeof(struct map_info), GFP_KERNEL); + ltq_mtd->map = devm_kzalloc(&pdev->dev, sizeof(struct map_info), + GFP_KERNEL); + if (!ltq_mtd->map) + return -ENOMEM; + ltq_mtd->map->phys = ltq_mtd->res->start; ltq_mtd->map->size = resource_size(ltq_mtd->res); ltq_mtd->map->virt = devm_ioremap_resource(&pdev->dev, ltq_mtd->res); - if (IS_ERR(ltq_mtd->map->virt)) { - err = PTR_ERR(ltq_mtd->map->virt); - goto err_out; - } + if (IS_ERR(ltq_mtd->map->virt)) + return PTR_ERR(ltq_mtd->map->virt); ltq_mtd->map->name = ltq_map_name; ltq_mtd->map->bankwidth = 2; @@ -155,8 +159,7 @@ ltq_mtd_probe(struct platform_device *pdev) if (!ltq_mtd->mtd) { dev_err(&pdev->dev, "probing failed\n"); - err = -ENXIO; - goto err_free; + return -ENXIO; } ltq_mtd->mtd->owner = THIS_MODULE; @@ -177,10 +180,6 @@ ltq_mtd_probe(struct platform_device *pdev) err_destroy: map_destroy(ltq_mtd->mtd); -err_free: - kfree(ltq_mtd->map); -err_out: - kfree(ltq_mtd); return err; } @@ -189,13 +188,9 @@ ltq_mtd_remove(struct platform_device *pdev) { struct ltq_mtd *ltq_mtd = platform_get_drvdata(pdev); - if (ltq_mtd) { - if (ltq_mtd->mtd) { - mtd_device_unregister(ltq_mtd->mtd); - map_destroy(ltq_mtd->mtd); - } - kfree(ltq_mtd->map); - kfree(ltq_mtd); + if (ltq_mtd && ltq_mtd->mtd) { + mtd_device_unregister(ltq_mtd->mtd); + map_destroy(ltq_mtd->mtd); } return 0; } diff --git a/drivers/mtd/maps/pxa2xx-flash.c b/drivers/mtd/maps/pxa2xx-flash.c index 0f55589..9aad854 100644 --- a/drivers/mtd/maps/pxa2xx-flash.c +++ b/drivers/mtd/maps/pxa2xx-flash.c @@ -61,7 +61,7 @@ static int pxa2xx_flash_probe(struct platform_device *pdev) if (!info) return -ENOMEM; - info->map.name = (char *) flash->name; + info->map.name = flash->name; info->map.bankwidth = flash->width; info->map.phys = res->start; info->map.size = resource_size(res); diff --git a/drivers/mtd/maps/sun_uflash.c b/drivers/mtd/maps/sun_uflash.c index d467f3b..39cc418 100644 --- a/drivers/mtd/maps/sun_uflash.c +++ b/drivers/mtd/maps/sun_uflash.c @@ -75,7 +75,7 @@ int uflash_devinit(struct platform_device *op, struct device_node *dp) up->name = of_get_property(dp, "model", NULL); if (up->name && 0 < strlen(up->name)) - up->map.name = (char *)up->name; + up->map.name = up->name; up->map.phys = op->resource[0].start; diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c index 92311a5..34c0b16 100644 --- a/drivers/mtd/mtdcore.c +++ b/drivers/mtd/mtdcore.c @@ -313,15 +313,7 @@ static struct attribute *mtd_attrs[] = { &dev_attr_bitflip_threshold.attr, NULL, }; - -static struct attribute_group mtd_group = { - .attrs = mtd_attrs, -}; - -static const struct attribute_group *mtd_groups[] = { - &mtd_group, - NULL, -}; +ATTRIBUTE_GROUPS(mtd); static struct device_type mtd_devtype = { .name = "mtd", diff --git a/drivers/mtd/mtdpart.c b/drivers/mtd/mtdpart.c index 6e732c3..3c7d6d7 100644 --- a/drivers/mtd/mtdpart.c +++ b/drivers/mtd/mtdpart.c @@ -534,7 +534,7 @@ out_register: return slave; } -int mtd_add_partition(struct mtd_info *master, char *name, +int mtd_add_partition(struct mtd_info *master, const char *name, long long offset, long long length) { struct mtd_partition part; @@ -672,22 +672,19 @@ static struct mtd_part_parser *get_partition_parser(const char *name) #define put_partition_parser(p) do { module_put((p)->owner); } while (0) -int register_mtd_parser(struct mtd_part_parser *p) +void register_mtd_parser(struct mtd_part_parser *p) { spin_lock(&part_parser_lock); list_add(&p->list, &part_parsers); spin_unlock(&part_parser_lock); - - return 0; } EXPORT_SYMBOL_GPL(register_mtd_parser); -int deregister_mtd_parser(struct mtd_part_parser *p) +void deregister_mtd_parser(struct mtd_part_parser *p) { spin_lock(&part_parser_lock); list_del(&p->list); spin_unlock(&part_parser_lock); - return 0; } EXPORT_SYMBOL_GPL(deregister_mtd_parser); diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 93ae6a6..90ff447 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -95,7 +95,7 @@ config MTD_NAND_OMAP2 platforms. config MTD_NAND_OMAP_BCH - depends on MTD_NAND && MTD_NAND_OMAP2 && ARCH_OMAP3 + depends on MTD_NAND_OMAP2 tristate "Support hardware based BCH error correction" default n select BCH @@ -326,11 +326,11 @@ config MTD_NAND_ATMEL on Atmel AT91 and AVR32 processors. config MTD_NAND_PXA3xx - tristate "Support for NAND flash devices on PXA3xx" + tristate "NAND support on PXA3xx and Armada 370/XP" depends on PXA3xx || ARCH_MMP || PLAT_ORION help This enables the driver for the NAND flash device found on - PXA3xx processors + PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). config MTD_NAND_SLC_LPC32XX tristate "NXP LPC32xx SLC Controller" @@ -458,17 +458,17 @@ config MTD_NAND_MXC config MTD_NAND_SH_FLCTL tristate "Support for NAND on Renesas SuperH FLCTL" - depends on SUPERH || ARCH_SHMOBILE + depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST help Several Renesas SuperH CPU has FLCTL. This option enables support for NAND Flash using FLCTL. config MTD_NAND_DAVINCI - tristate "Support NAND on DaVinci SoC" - depends on ARCH_DAVINCI + tristate "Support NAND on DaVinci/Keystone SoC" + depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) help Enable the driver for NAND flash chips on Texas Instruments - DaVinci processors. + DaVinci/Keystone processors. config MTD_NAND_TXX9NDFMC tristate "NAND Flash support for TXx9 SoC" diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index 59f08c4..c36e9b8 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -1961,10 +1961,8 @@ static int atmel_nand_probe(struct platform_device *pdev) /* Allocate memory for the device structure (and zero it) */ host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); - if (!host) { - printk(KERN_ERR "atmel_nand: failed to allocate device structure.\n"); + if (!host) return -ENOMEM; - } res = platform_driver_register(&atmel_nand_nfc_driver); if (res) @@ -2062,14 +2060,14 @@ static int atmel_nand_probe(struct platform_device *pdev) } if (gpio_get_value(host->board.det_pin)) { - printk(KERN_INFO "No SmartMedia card inserted.\n"); + dev_info(&pdev->dev, "No SmartMedia card inserted.\n"); res = -ENXIO; goto err_no_card; } } if (host->board.on_flash_bbt || on_flash_bbt) { - printk(KERN_INFO "atmel_nand: Use On Flash BBT\n"); + dev_info(&pdev->dev, "Use On Flash BBT\n"); nand_chip->bbt_options |= NAND_BBT_USE_FLASH; } diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/au1550nd.c index ae8dd7c..2880d88 100644 --- a/drivers/mtd/nand/au1550nd.c +++ b/drivers/mtd/nand/au1550nd.c @@ -418,10 +418,8 @@ static int au1550nd_probe(struct platform_device *pdev) } ctx = kzalloc(sizeof(*ctx), GFP_KERNEL); - if (!ctx) { - dev_err(&pdev->dev, "no memory for NAND context\n"); + if (!ctx) return -ENOMEM; - } r = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!r) { @@ -480,6 +478,8 @@ static int au1550nd_probe(struct platform_device *pdev) mtd_device_register(&ctx->info, pd->parts, pd->num_parts); + platform_set_drvdata(pdev, ctx); + return 0; out3: diff --git a/drivers/mtd/nand/bf5xx_nand.c b/drivers/mtd/nand/bf5xx_nand.c index 2c42e12..94f55db 100644 --- a/drivers/mtd/nand/bf5xx_nand.c +++ b/drivers/mtd/nand/bf5xx_nand.c @@ -745,7 +745,6 @@ static int bf5xx_nand_probe(struct platform_device *pdev) info = kzalloc(sizeof(*info), GFP_KERNEL); if (info == NULL) { - dev_err(&pdev->dev, "no memory for flash info\n"); err = -ENOMEM; goto out_err_kzalloc; } diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c index c34985a5..f2f64ad 100644 --- a/drivers/mtd/nand/cafe_nand.c +++ b/drivers/mtd/nand/cafe_nand.c @@ -640,10 +640,8 @@ static int cafe_nand_probe(struct pci_dev *pdev, pci_set_master(pdev); mtd = kzalloc(sizeof(*mtd) + sizeof(struct cafe_priv), GFP_KERNEL); - if (!mtd) { - dev_warn(&pdev->dev, "failed to alloc mtd_info\n"); + if (!mtd) return -ENOMEM; - } cafe = (void *)(&mtd[1]); mtd->dev.parent = &pdev->dev; diff --git a/drivers/mtd/nand/cmx270_nand.c b/drivers/mtd/nand/cmx270_nand.c index 39b2ef8..66ec95e 100644 --- a/drivers/mtd/nand/cmx270_nand.c +++ b/drivers/mtd/nand/cmx270_nand.c @@ -164,7 +164,6 @@ static int __init cmx270_init(void) sizeof(struct nand_chip), GFP_KERNEL); if (!cmx270_nand_mtd) { - pr_debug("Unable to allocate CM-X270 NAND MTD device structure.\n"); ret = -ENOMEM; goto err_kzalloc; } diff --git a/drivers/mtd/nand/cs553x_nand.c b/drivers/mtd/nand/cs553x_nand.c index d469a9a..88109d3 100644 --- a/drivers/mtd/nand/cs553x_nand.c +++ b/drivers/mtd/nand/cs553x_nand.c @@ -199,7 +199,6 @@ static int __init cs553x_init_one(int cs, int mmio, unsigned long adr) /* Allocate memory for MTD device structure and private data */ new_mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL); if (!new_mtd) { - printk(KERN_WARNING "Unable to allocate CS553X NAND MTD device structure.\n"); err = -ENOMEM; goto out; } diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c index b77a01e..a4989ec 100644 --- a/drivers/mtd/nand/davinci_nand.c +++ b/drivers/mtd/nand/davinci_nand.c @@ -35,6 +35,7 @@ #include <linux/slab.h> #include <linux/of_device.h> #include <linux/of.h> +#include <linux/of_mtd.h> #include <linux/platform_data/mtd-davinci.h> #include <linux/platform_data/mtd-davinci-aemif.h> @@ -487,7 +488,7 @@ static int nand_davinci_dev_ready(struct mtd_info *mtd) * ten ECC bytes plus the manufacturer's bad block marker byte, and * and not overlapping the default BBT markers. */ -static struct nand_ecclayout hwecc4_small __initconst = { +static struct nand_ecclayout hwecc4_small = { .eccbytes = 10, .eccpos = { 0, 1, 2, 3, 4, /* offset 5 holds the badblock marker */ @@ -503,7 +504,7 @@ static struct nand_ecclayout hwecc4_small __initconst = { * storing ten ECC bytes plus the manufacturer's bad block marker byte, * and not overlapping the default BBT markers. */ -static struct nand_ecclayout hwecc4_2048 __initconst = { +static struct nand_ecclayout hwecc4_2048 = { .eccbytes = 40, .eccpos = { /* at the end of spare sector */ @@ -534,17 +535,19 @@ static struct davinci_nand_pdata struct davinci_nand_pdata *pdata; const char *mode; u32 prop; - int len; pdata = devm_kzalloc(&pdev->dev, sizeof(struct davinci_nand_pdata), GFP_KERNEL); pdev->dev.platform_data = pdata; if (!pdata) - return NULL; + return ERR_PTR(-ENOMEM); if (!of_property_read_u32(pdev->dev.of_node, "ti,davinci-chipselect", &prop)) pdev->id = prop; + else + return ERR_PTR(-EINVAL); + if (!of_property_read_u32(pdev->dev.of_node, "ti,davinci-mask-ale", &prop)) pdata->mask_ale = prop; @@ -555,6 +558,8 @@ static struct davinci_nand_pdata "ti,davinci-mask-chipsel", &prop)) pdata->mask_chipsel = prop; if (!of_property_read_string(pdev->dev.of_node, + "nand-ecc-mode", &mode) || + !of_property_read_string(pdev->dev.of_node, "ti,davinci-ecc-mode", &mode)) { if (!strncmp("none", mode, 4)) pdata->ecc_mode = NAND_ECC_NONE; @@ -566,12 +571,16 @@ static struct davinci_nand_pdata if (!of_property_read_u32(pdev->dev.of_node, "ti,davinci-ecc-bits", &prop)) pdata->ecc_bits = prop; - if (!of_property_read_u32(pdev->dev.of_node, + + prop = of_get_nand_bus_width(pdev->dev.of_node); + if (0 < prop || !of_property_read_u32(pdev->dev.of_node, "ti,davinci-nand-buswidth", &prop)) if (prop == 16) pdata->options |= NAND_BUSWIDTH_16; - if (of_find_property(pdev->dev.of_node, - "ti,davinci-nand-use-bbt", &len)) + if (of_property_read_bool(pdev->dev.of_node, + "nand-on-flash-bbt") || + of_property_read_bool(pdev->dev.of_node, + "ti,davinci-nand-use-bbt")) pdata->bbt_options = NAND_BBT_USE_FLASH; } @@ -585,7 +594,7 @@ static struct davinci_nand_pdata } #endif -static int __init nand_davinci_probe(struct platform_device *pdev) +static int nand_davinci_probe(struct platform_device *pdev) { struct davinci_nand_pdata *pdata; struct davinci_nand_info *info; @@ -598,6 +607,9 @@ static int __init nand_davinci_probe(struct platform_device *pdev) nand_ecc_modes_t ecc_mode; pdata = nand_davinci_get_pdata(pdev); + if (IS_ERR(pdata)) + return PTR_ERR(pdata); + /* insist on board-specific configuration */ if (!pdata) return -ENODEV; @@ -607,11 +619,8 @@ static int __init nand_davinci_probe(struct platform_device *pdev) return -ENODEV; info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); - if (!info) { - dev_err(&pdev->dev, "unable to allocate memory\n"); - ret = -ENOMEM; - goto err_nomem; - } + if (!info) + return -ENOMEM; platform_set_drvdata(pdev, info); @@ -619,19 +628,23 @@ static int __init nand_davinci_probe(struct platform_device *pdev) res2 = platform_get_resource(pdev, IORESOURCE_MEM, 1); if (!res1 || !res2) { dev_err(&pdev->dev, "resource missing\n"); - ret = -EINVAL; - goto err_nomem; + return -EINVAL; } vaddr = devm_ioremap_resource(&pdev->dev, res1); - if (IS_ERR(vaddr)) { - ret = PTR_ERR(vaddr); - goto err_ioremap; - } - base = devm_ioremap_resource(&pdev->dev, res2); - if (IS_ERR(base)) { - ret = PTR_ERR(base); - goto err_ioremap; + if (IS_ERR(vaddr)) + return PTR_ERR(vaddr); + + /* + * This registers range is used to setup NAND settings. In case with + * TI AEMIF driver, the same memory address range is requested already + * by AEMIF, so we cannot request it twice, just ioremap. + * The AEMIF and NAND drivers not use the same registers in this range. + */ + base = devm_ioremap(&pdev->dev, res2->start, resource_size(res2)); + if (!base) { + dev_err(&pdev->dev, "ioremap failed for resource %pR\n", res2); + return -EADDRNOTAVAIL; } info->dev = &pdev->dev; @@ -699,7 +712,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) spin_unlock_irq(&davinci_nand_lock); if (ret == -EBUSY) - goto err_ecc; + return ret; info->chip.ecc.calculate = nand_davinci_calculate_4bit; info->chip.ecc.correct = nand_davinci_correct_4bit; @@ -715,8 +728,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) info->chip.ecc.strength = pdata->ecc_bits; break; default: - ret = -EINVAL; - goto err_ecc; + return -EINVAL; } info->chip.ecc.mode = ecc_mode; @@ -724,7 +736,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) if (IS_ERR(info->clk)) { ret = PTR_ERR(info->clk); dev_dbg(&pdev->dev, "unable to get AEMIF clock, err %d\n", ret); - goto err_clk; + return ret; } ret = clk_prepare_enable(info->clk); @@ -753,7 +765,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) info->core_chipsel); if (ret < 0) { dev_dbg(&pdev->dev, "NAND timing values setup fail\n"); - goto err_timing; + goto err; } spin_lock_irq(&davinci_nand_lock); @@ -769,7 +781,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) ret = nand_scan_ident(&info->mtd, pdata->mask_chipsel ? 2 : 1, NULL); if (ret < 0) { dev_dbg(&pdev->dev, "no NAND chip(s) found\n"); - goto err_scan; + goto err; } /* Update ECC layout if needed ... for 1-bit HW ECC, the default @@ -783,7 +795,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) if (!chunks || info->mtd.oobsize < 16) { dev_dbg(&pdev->dev, "too small\n"); ret = -EINVAL; - goto err_scan; + goto err; } /* For small page chips, preserve the manufacturer's @@ -814,7 +826,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev) dev_warn(&pdev->dev, "no 4-bit ECC support yet " "for 4KiB-page NAND\n"); ret = -EIO; - goto err_scan; + goto err; syndrome_done: info->chip.ecc.layout = &info->ecclayout; @@ -822,7 +834,7 @@ syndrome_done: ret = nand_scan_tail(&info->mtd); if (ret < 0) - goto err_scan; + goto err; if (pdata->parts) ret = mtd_device_parse_register(&info->mtd, NULL, NULL, @@ -835,7 +847,7 @@ syndrome_done: NULL, 0); } if (ret < 0) - goto err_scan; + goto err; val = davinci_nand_readl(info, NRCSR_OFFSET); dev_info(&pdev->dev, "controller rev. %d.%d\n", @@ -843,8 +855,7 @@ syndrome_done: return 0; -err_scan: -err_timing: +err: clk_disable_unprepare(info->clk); err_clk_enable: @@ -852,15 +863,10 @@ err_clk_enable: if (ecc_mode == NAND_ECC_HW_SYNDROME) ecc4_busy = false; spin_unlock_irq(&davinci_nand_lock); - -err_ecc: -err_clk: -err_ioremap: -err_nomem: return ret; } -static int __exit nand_davinci_remove(struct platform_device *pdev) +static int nand_davinci_remove(struct platform_device *pdev) { struct davinci_nand_info *info = platform_get_drvdata(pdev); @@ -877,7 +883,8 @@ static int __exit nand_davinci_remove(struct platform_device *pdev) } static struct platform_driver nand_davinci_driver = { - .remove = __exit_p(nand_davinci_remove), + .probe = nand_davinci_probe, + .remove = nand_davinci_remove, .driver = { .name = "davinci_nand", .owner = THIS_MODULE, @@ -886,7 +893,7 @@ static struct platform_driver nand_davinci_driver = { }; MODULE_ALIAS("platform:davinci_nand"); -module_platform_driver_probe(nand_davinci_driver, nand_davinci_probe); +module_platform_driver(nand_davinci_driver); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Texas Instruments"); diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index 370b9dd..c07cd57 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -125,7 +125,6 @@ static void reset_buf(struct denali_nand_info *denali) static void write_byte_to_buf(struct denali_nand_info *denali, uint8_t byte) { - BUG_ON(denali->buf.tail >= sizeof(denali->buf.buf)); denali->buf.buf[denali->buf.tail++] = byte; } @@ -897,7 +896,7 @@ static void read_oob_data(struct mtd_info *mtd, uint8_t *buf, int page) /* this function examines buffers to see if they contain data that * indicate that the buffer is part of an erased region of flash. */ -bool is_erased(uint8_t *buf, int len) +static bool is_erased(uint8_t *buf, int len) { int i = 0; for (i = 0; i < len; i++) @@ -1429,20 +1428,12 @@ int denali_init(struct denali_nand_info *denali) } } - /* Is 32-bit DMA supported? */ - ret = dma_set_mask(denali->dev, DMA_BIT_MASK(32)); - if (ret) { - pr_err("Spectra: no usable DMA configuration\n"); - return ret; - } - denali->buf.dma_buf = dma_map_single(denali->dev, denali->buf.buf, - DENALI_BUF_SIZE, - DMA_BIDIRECTIONAL); + /* allocate a temporary buffer for nand_scan_ident() */ + denali->buf.buf = devm_kzalloc(denali->dev, PAGE_SIZE, + GFP_DMA | GFP_KERNEL); + if (!denali->buf.buf) + return -ENOMEM; - if (dma_mapping_error(denali->dev, denali->buf.dma_buf)) { - dev_err(denali->dev, "Spectra: failed to map DMA buffer\n"); - return -EIO; - } denali->mtd.dev.parent = denali->dev; denali_hw_init(denali); denali_drv_init(denali); @@ -1475,12 +1466,29 @@ int denali_init(struct denali_nand_info *denali) goto failed_req_irq; } - /* MTD supported page sizes vary by kernel. We validate our - * kernel supports the device here. - */ - if (denali->mtd.writesize > NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE) { - ret = -ENODEV; - pr_err("Spectra: device size not supported by this version of MTD."); + /* allocate the right size buffer now */ + devm_kfree(denali->dev, denali->buf.buf); + denali->buf.buf = devm_kzalloc(denali->dev, + denali->mtd.writesize + denali->mtd.oobsize, + GFP_KERNEL); + if (!denali->buf.buf) { + ret = -ENOMEM; + goto failed_req_irq; + } + + /* Is 32-bit DMA supported? */ + ret = dma_set_mask(denali->dev, DMA_BIT_MASK(32)); + if (ret) { + pr_err("Spectra: no usable DMA configuration\n"); + goto failed_req_irq; + } + + denali->buf.dma_buf = dma_map_single(denali->dev, denali->buf.buf, + denali->mtd.writesize + denali->mtd.oobsize, + DMA_BIDIRECTIONAL); + if (dma_mapping_error(denali->dev, denali->buf.dma_buf)) { + dev_err(denali->dev, "Spectra: failed to map DMA buffer\n"); + ret = -EIO; goto failed_req_irq; } @@ -1602,7 +1610,8 @@ EXPORT_SYMBOL(denali_init); void denali_remove(struct denali_nand_info *denali) { denali_irq_cleanup(denali->irq, denali); - dma_unmap_single(denali->dev, denali->buf.dma_buf, DENALI_BUF_SIZE, + dma_unmap_single(denali->dev, denali->buf.dma_buf, + denali->mtd.writesize + denali->mtd.oobsize, DMA_BIDIRECTIONAL); } EXPORT_SYMBOL(denali_remove); diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/denali.h index cec5712..9668174 100644 --- a/drivers/mtd/nand/denali.h +++ b/drivers/mtd/nand/denali.h @@ -455,12 +455,10 @@ #define ECC_SECTOR_SIZE 512 -#define DENALI_BUF_SIZE (NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE) - struct nand_buf { int head; int tail; - uint8_t buf[DENALI_BUF_SIZE]; + uint8_t *buf; dma_addr_t dma_buf; }; diff --git a/drivers/mtd/nand/denali_dt.c b/drivers/mtd/nand/denali_dt.c index 9253024..babb02c 100644 --- a/drivers/mtd/nand/denali_dt.c +++ b/drivers/mtd/nand/denali_dt.c @@ -108,7 +108,7 @@ static int denali_dt_probe(struct platform_device *ofdev) denali->dev->dma_mask = NULL; } - dt->clk = clk_get(&ofdev->dev, NULL); + dt->clk = devm_clk_get(&ofdev->dev, NULL); if (IS_ERR(dt->clk)) { dev_err(&ofdev->dev, "no clk available\n"); return PTR_ERR(dt->clk); @@ -124,7 +124,6 @@ static int denali_dt_probe(struct platform_device *ofdev) out_disable_clk: clk_disable_unprepare(dt->clk); - clk_put(dt->clk); return ret; } @@ -135,7 +134,6 @@ static int denali_dt_remove(struct platform_device *ofdev) denali_remove(&dt->denali); clk_disable(dt->clk); - clk_put(dt->clk); return 0; } diff --git a/drivers/mtd/nand/denali_pci.c b/drivers/mtd/nand/denali_pci.c index 033f177..6e2f387 100644 --- a/drivers/mtd/nand/denali_pci.c +++ b/drivers/mtd/nand/denali_pci.c @@ -21,7 +21,7 @@ #define DENALI_NAND_NAME "denali-nand-pci" /* List of platforms this NAND controller has be integrated into */ -static DEFINE_PCI_DEVICE_TABLE(denali_pci_ids) = { +static const struct pci_device_id denali_pci_ids[] = { { PCI_VDEVICE(INTEL, 0x0701), INTEL_CE4100 }, { PCI_VDEVICE(INTEL, 0x0809), INTEL_MRST }, { /* end: all zeroes */ } @@ -131,7 +131,6 @@ static struct pci_driver denali_pci_driver = { static int denali_init_pci(void) { - pr_info("Spectra MTD driver built on %s @ %s\n", __DATE__, __TIME__); return pci_register_driver(&denali_pci_driver); } module_init(denali_init_pci); diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c index b68a495..fec31d7 100644 --- a/drivers/mtd/nand/diskonchip.c +++ b/drivers/mtd/nand/diskonchip.c @@ -1058,7 +1058,6 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, struct mtd_partitio buf = kmalloc(mtd->writesize, GFP_KERNEL); if (!buf) { - printk(KERN_ERR "DiskOnChip mediaheader kmalloc failed!\n"); return 0; } if (!(numheaders = find_media_headers(mtd, buf, "ANAND", 1))) @@ -1166,7 +1165,6 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, struct mtd_partiti buf = kmalloc(mtd->writesize, GFP_KERNEL); if (!buf) { - printk(KERN_ERR "DiskOnChip mediaheader kmalloc failed!\n"); return 0; } @@ -1440,10 +1438,13 @@ static int __init doc_probe(unsigned long physadr) int reg, len, numchips; int ret = 0; + if (!request_mem_region(physadr, DOC_IOREMAP_LEN, NULL)) + return -EBUSY; virtadr = ioremap(physadr, DOC_IOREMAP_LEN); if (!virtadr) { printk(KERN_ERR "Diskonchip ioremap failed: 0x%x bytes at 0x%lx\n", DOC_IOREMAP_LEN, physadr); - return -EIO; + ret = -EIO; + goto error_ioremap; } /* It's not possible to cleanly detect the DiskOnChip - the @@ -1561,7 +1562,6 @@ static int __init doc_probe(unsigned long physadr) sizeof(struct nand_chip) + sizeof(struct doc_priv) + (2 * sizeof(struct nand_bbt_descr)); mtd = kzalloc(len, GFP_KERNEL); if (!mtd) { - printk(KERN_ERR "DiskOnChip kmalloc (%d bytes) failed!\n", len); ret = -ENOMEM; goto fail; } @@ -1629,6 +1629,10 @@ static int __init doc_probe(unsigned long physadr) WriteDOC(save_control, virtadr, DOCControl); fail: iounmap(virtadr); + +error_ioremap: + release_mem_region(physadr, DOC_IOREMAP_LEN); + return ret; } @@ -1645,6 +1649,7 @@ static void release_nanddoc(void) nextmtd = doc->nextdoc; nand_release(mtd); iounmap(doc->virtadr); + release_mem_region(doc->physadr, DOC_IOREMAP_LEN); kfree(mtd); } } diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index c966fc7..bcf6080 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -847,7 +847,6 @@ static int fsl_elbc_nand_probe(struct platform_device *pdev) if (!fsl_lbc_ctrl_dev->nand) { elbc_fcm_ctrl = kzalloc(sizeof(*elbc_fcm_ctrl), GFP_KERNEL); if (!elbc_fcm_ctrl) { - dev_err(dev, "failed to allocate memory\n"); mutex_unlock(&fsl_elbc_nand_mutex); ret = -ENOMEM; goto err; @@ -875,7 +874,7 @@ static int fsl_elbc_nand_probe(struct platform_device *pdev) goto err; } - priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", (unsigned)res.start); + priv->mtd.name = kasprintf(GFP_KERNEL, "%llx.flash", (u64)res.start); if (!priv->mtd.name) { ret = -ENOMEM; goto err; diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c index 4335577..90ca7e7 100644 --- a/drivers/mtd/nand/fsl_ifc_nand.c +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -1060,7 +1060,6 @@ static int fsl_ifc_nand_probe(struct platform_device *dev) if (!fsl_ifc_ctrl_dev->nand) { ifc_nand_ctrl = kzalloc(sizeof(*ifc_nand_ctrl), GFP_KERNEL); if (!ifc_nand_ctrl) { - dev_err(&dev->dev, "failed to allocate memory\n"); mutex_unlock(&fsl_ifc_nand_mutex); return -ENOMEM; } @@ -1101,7 +1100,7 @@ static int fsl_ifc_nand_probe(struct platform_device *dev) IFC_NAND_EVTER_INTR_FTOERIR_EN | IFC_NAND_EVTER_INTR_WPERIR_EN, &ifc->ifc_nand.nand_evter_intr_en); - priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", (unsigned)res.start); + priv->mtd.name = kasprintf(GFP_KERNEL, "%llx.flash", (u64)res.start); if (!priv->mtd.name) { ret = -ENOMEM; goto err; diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c index 8b27522..1550692 100644 --- a/drivers/mtd/nand/fsmc_nand.c +++ b/drivers/mtd/nand/fsmc_nand.c @@ -889,10 +889,8 @@ static int fsmc_nand_probe_config_dt(struct platform_device *pdev, pdata->nand_timings = devm_kzalloc(&pdev->dev, sizeof(*pdata->nand_timings), GFP_KERNEL); - if (!pdata->nand_timings) { - dev_err(&pdev->dev, "no memory for nand_timing\n"); + if (!pdata->nand_timings) return -ENOMEM; - } of_property_read_u8_array(np, "timings", (u8 *)pdata->nand_timings, sizeof(*pdata->nand_timings)); @@ -950,10 +948,8 @@ static int __init fsmc_nand_probe(struct platform_device *pdev) /* Allocate memory for the device structure (and zero it) */ host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); - if (!host) { - dev_err(&pdev->dev, "failed to allocate device structure\n"); + if (!host) return -ENOMEM; - } res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand_data"); host->data_va = devm_ioremap_resource(&pdev->dev, res); @@ -1108,8 +1104,8 @@ static int __init fsmc_nand_probe(struct platform_device *pdev) host->ecc_place = &fsmc_ecc4_lp_place; break; default: - printk(KERN_WARNING "No oob scheme defined for " - "oobsize %d\n", mtd->oobsize); + dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n", + mtd->oobsize); BUG(); } } else { @@ -1124,8 +1120,8 @@ static int __init fsmc_nand_probe(struct platform_device *pdev) nand->ecc.layout = &fsmc_ecc1_128_layout; break; default: - printk(KERN_WARNING "No oob scheme defined for " - "oobsize %d\n", mtd->oobsize); + dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n", + mtd->oobsize); BUG(); } } diff --git a/drivers/mtd/nand/gpio.c b/drivers/mtd/nand/gpio.c index e826f89..8e6148a 100644 --- a/drivers/mtd/nand/gpio.c +++ b/drivers/mtd/nand/gpio.c @@ -132,13 +132,17 @@ static int gpio_nand_get_config_of(const struct device *dev, static struct resource *gpio_nand_get_io_sync_of(struct platform_device *pdev) { - struct resource *r = devm_kzalloc(&pdev->dev, sizeof(*r), GFP_KERNEL); + struct resource *r; u64 addr; - if (!r || of_property_read_u64(pdev->dev.of_node, + if (of_property_read_u64(pdev->dev.of_node, "gpio-control-nand,io-sync-reg", &addr)) return NULL; + r = devm_kzalloc(&pdev->dev, sizeof(*r), GFP_KERNEL); + if (!r) + return NULL; + r->start = addr; r->end = r->start + 0x3; r->flags = IORESOURCE_MEM; @@ -211,10 +215,8 @@ static int gpio_nand_probe(struct platform_device *pdev) return -EINVAL; gpiomtd = devm_kzalloc(&pdev->dev, sizeof(*gpiomtd), GFP_KERNEL); - if (!gpiomtd) { - dev_err(&pdev->dev, "failed to create NAND MTD\n"); + if (!gpiomtd) return -ENOMEM; - } chip = &gpiomtd->nand_chip; diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c index aaced29..dd1df60 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c @@ -20,6 +20,7 @@ */ #include <linux/delay.h> #include <linux/clk.h> +#include <linux/slab.h> #include "gpmi-nand.h" #include "gpmi-regs.h" @@ -207,30 +208,41 @@ void gpmi_dump_info(struct gpmi_nand_data *this) u32 reg; int i; - pr_err("Show GPMI registers :\n"); + dev_err(this->dev, "Show GPMI registers :\n"); for (i = 0; i <= HW_GPMI_DEBUG / 0x10 + 1; i++) { reg = readl(r->gpmi_regs + i * 0x10); - pr_err("offset 0x%.3x : 0x%.8x\n", i * 0x10, reg); + dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg); } /* start to print out the BCH info */ - pr_err("Show BCH registers :\n"); + dev_err(this->dev, "Show BCH registers :\n"); for (i = 0; i <= HW_BCH_VERSION / 0x10 + 1; i++) { reg = readl(r->bch_regs + i * 0x10); - pr_err("offset 0x%.3x : 0x%.8x\n", i * 0x10, reg); + dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg); } - pr_err("BCH Geometry :\n"); - pr_err("GF length : %u\n", geo->gf_len); - pr_err("ECC Strength : %u\n", geo->ecc_strength); - pr_err("Page Size in Bytes : %u\n", geo->page_size); - pr_err("Metadata Size in Bytes : %u\n", geo->metadata_size); - pr_err("ECC Chunk Size in Bytes: %u\n", geo->ecc_chunk_size); - pr_err("ECC Chunk Count : %u\n", geo->ecc_chunk_count); - pr_err("Payload Size in Bytes : %u\n", geo->payload_size); - pr_err("Auxiliary Size in Bytes: %u\n", geo->auxiliary_size); - pr_err("Auxiliary Status Offset: %u\n", geo->auxiliary_status_offset); - pr_err("Block Mark Byte Offset : %u\n", geo->block_mark_byte_offset); - pr_err("Block Mark Bit Offset : %u\n", geo->block_mark_bit_offset); + dev_err(this->dev, "BCH Geometry :\n" + "GF length : %u\n" + "ECC Strength : %u\n" + "Page Size in Bytes : %u\n" + "Metadata Size in Bytes : %u\n" + "ECC Chunk Size in Bytes: %u\n" + "ECC Chunk Count : %u\n" + "Payload Size in Bytes : %u\n" + "Auxiliary Size in Bytes: %u\n" + "Auxiliary Status Offset: %u\n" + "Block Mark Byte Offset : %u\n" + "Block Mark Bit Offset : %u\n", + geo->gf_len, + geo->ecc_strength, + geo->page_size, + geo->metadata_size, + geo->ecc_chunk_size, + geo->ecc_chunk_count, + geo->payload_size, + geo->auxiliary_size, + geo->auxiliary_status_offset, + geo->block_mark_byte_offset, + geo->block_mark_bit_offset); } /* Configures the geometry for BCH. */ @@ -265,8 +277,8 @@ int bch_set_geometry(struct gpmi_nand_data *this) * chip, otherwise it will lock up. So we skip resetting BCH on the MX23. * On the other hand, the MX28 needs the reset, because one case has been * seen where the BCH produced ECC errors constantly after 10000 - * consecutive reboots. The latter case has not been seen on the MX23 yet, - * still we don't know if it could happen there as well. + * consecutive reboots. The latter case has not been seen on the MX23 + * yet, still we don't know if it could happen there as well. */ ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this)); if (ret) @@ -353,7 +365,7 @@ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, improved_timing_is_available = (target.tREA_in_ns >= 0) && (target.tRLOH_in_ns >= 0) && - (target.tRHOH_in_ns >= 0) ; + (target.tRHOH_in_ns >= 0); /* Inspect the clock. */ nfc->clock_frequency_in_hz = clk_get_rate(r->clock[0]); @@ -911,10 +923,14 @@ static int enable_edo_mode(struct gpmi_nand_data *this, int mode) struct resources *r = &this->resources; struct nand_chip *nand = &this->nand; struct mtd_info *mtd = &this->mtd; - uint8_t feature[ONFI_SUBFEATURE_PARAM_LEN] = {}; + uint8_t *feature; unsigned long rate; int ret; + feature = kzalloc(ONFI_SUBFEATURE_PARAM_LEN, GFP_KERNEL); + if (!feature) + return -ENOMEM; + nand->select_chip(mtd, 0); /* [1] send SET FEATURE commond to NAND */ @@ -942,11 +958,13 @@ static int enable_edo_mode(struct gpmi_nand_data *this, int mode) this->flags |= GPMI_ASYNC_EDO_ENABLED; this->timing_mode = mode; + kfree(feature); dev_info(this->dev, "enable the asynchronous EDO mode %d\n", mode); return 0; err_out: nand->select_chip(mtd, -1); + kfree(feature); dev_err(this->dev, "mode:%d ,failed in set feature.\n", mode); return -EINVAL; } @@ -986,7 +1004,7 @@ void gpmi_begin(struct gpmi_nand_data *this) /* Enable the clock. */ ret = gpmi_enable_clk(this); if (ret) { - pr_err("We failed in enable the clk\n"); + dev_err(this->dev, "We failed in enable the clk\n"); goto err_out; } @@ -1003,7 +1021,7 @@ void gpmi_begin(struct gpmi_nand_data *this) /* [1] Set HW_GPMI_TIMING0 */ reg = BF_GPMI_TIMING0_ADDRESS_SETUP(hw.address_setup_in_cycles) | BF_GPMI_TIMING0_DATA_HOLD(hw.data_hold_in_cycles) | - BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles) ; + BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles); writel(reg, gpmi_regs + HW_GPMI_TIMING0); @@ -1090,7 +1108,7 @@ int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip) mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip); reg = readl(r->gpmi_regs + HW_GPMI_STAT); } else - pr_err("unknow arch.\n"); + dev_err(this->dev, "unknow arch.\n"); return reg & mask; } @@ -1121,10 +1139,8 @@ int gpmi_send_command(struct gpmi_nand_data *this) desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio, ARRAY_SIZE(pio), DMA_TRANS_NONE, 0); - if (!desc) { - pr_err("step 1 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [2] send out the COMMAND + ADDRESS string stored in @buffer */ sgl = &this->cmd_sgl; @@ -1134,11 +1150,8 @@ int gpmi_send_command(struct gpmi_nand_data *this) desc = dmaengine_prep_slave_sg(channel, sgl, 1, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); - - if (!desc) { - pr_err("step 2 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [3] submit the DMA */ set_dma_type(this, DMA_FOR_COMMAND); @@ -1167,20 +1180,17 @@ int gpmi_send_data(struct gpmi_nand_data *this) pio[1] = 0; desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio, ARRAY_SIZE(pio), DMA_TRANS_NONE, 0); - if (!desc) { - pr_err("step 1 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [2] send DMA request */ prepare_data_dma(this, DMA_TO_DEVICE); desc = dmaengine_prep_slave_sg(channel, &this->data_sgl, 1, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); - if (!desc) { - pr_err("step 2 error\n"); - return -1; - } + if (!desc) + return -EINVAL; + /* [3] submit the DMA */ set_dma_type(this, DMA_FOR_WRITE_DATA); return start_dma_without_bch_irq(this, desc); @@ -1204,20 +1214,16 @@ int gpmi_read_data(struct gpmi_nand_data *this) desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio, ARRAY_SIZE(pio), DMA_TRANS_NONE, 0); - if (!desc) { - pr_err("step 1 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [2] : send DMA request */ prepare_data_dma(this, DMA_FROM_DEVICE); desc = dmaengine_prep_slave_sg(channel, &this->data_sgl, 1, DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); - if (!desc) { - pr_err("step 2 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [3] : submit the DMA */ set_dma_type(this, DMA_FOR_READ_DATA); @@ -1262,10 +1268,9 @@ int gpmi_send_page(struct gpmi_nand_data *this, (struct scatterlist *)pio, ARRAY_SIZE(pio), DMA_TRANS_NONE, DMA_CTRL_ACK); - if (!desc) { - pr_err("step 2 error\n"); - return -1; - } + if (!desc) + return -EINVAL; + set_dma_type(this, DMA_FOR_WRITE_ECC_PAGE); return start_dma_with_bch_irq(this, desc); } @@ -1297,10 +1302,8 @@ int gpmi_read_page(struct gpmi_nand_data *this, desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio, 2, DMA_TRANS_NONE, 0); - if (!desc) { - pr_err("step 1 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [2] Enable the BCH block and read. */ command_mode = BV_GPMI_CTRL0_COMMAND_MODE__READ; @@ -1327,10 +1330,8 @@ int gpmi_read_page(struct gpmi_nand_data *this, (struct scatterlist *)pio, ARRAY_SIZE(pio), DMA_TRANS_NONE, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); - if (!desc) { - pr_err("step 2 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [3] Disable the BCH block */ command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY; @@ -1348,10 +1349,8 @@ int gpmi_read_page(struct gpmi_nand_data *this, (struct scatterlist *)pio, 3, DMA_TRANS_NONE, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); - if (!desc) { - pr_err("step 3 error\n"); - return -1; - } + if (!desc) + return -EINVAL; /* [4] submit the DMA */ set_dma_type(this, DMA_FOR_READ_ECC_PAGE); diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index dabbc14..ca6369f 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -18,9 +18,6 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ - -#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt - #include <linux/clk.h> #include <linux/slab.h> #include <linux/interrupt.h> @@ -352,6 +349,9 @@ static int legacy_set_geometry(struct gpmi_nand_data *this) int common_nfc_set_geometry(struct gpmi_nand_data *this) { + if (of_property_read_bool(this->dev->of_node, "fsl,use-minimum-ecc") + && set_geometry_by_ecc_info(this)) + return 0; return legacy_set_geometry(this); } @@ -367,25 +367,28 @@ void prepare_data_dma(struct gpmi_nand_data *this, enum dma_data_direction dr) struct scatterlist *sgl = &this->data_sgl; int ret; - this->direct_dma_map_ok = true; - /* first try to map the upper buffer directly */ - sg_init_one(sgl, this->upper_buf, this->upper_len); - ret = dma_map_sg(this->dev, sgl, 1, dr); - if (ret == 0) { - /* We have to use our own DMA buffer. */ - sg_init_one(sgl, this->data_buffer_dma, PAGE_SIZE); - - if (dr == DMA_TO_DEVICE) - memcpy(this->data_buffer_dma, this->upper_buf, - this->upper_len); - + if (virt_addr_valid(this->upper_buf) && + !object_is_on_stack(this->upper_buf)) { + sg_init_one(sgl, this->upper_buf, this->upper_len); ret = dma_map_sg(this->dev, sgl, 1, dr); if (ret == 0) - pr_err("DMA mapping failed.\n"); + goto map_fail; - this->direct_dma_map_ok = false; + this->direct_dma_map_ok = true; + return; } + +map_fail: + /* We have to use our own DMA buffer. */ + sg_init_one(sgl, this->data_buffer_dma, this->upper_len); + + if (dr == DMA_TO_DEVICE) + memcpy(this->data_buffer_dma, this->upper_buf, this->upper_len); + + dma_map_sg(this->dev, sgl, 1, dr); + + this->direct_dma_map_ok = false; } /* This will be called after the DMA operation is finished. */ @@ -416,7 +419,7 @@ static void dma_irq_callback(void *param) break; default: - pr_err("in wrong DMA operation.\n"); + dev_err(this->dev, "in wrong DMA operation.\n"); } complete(dma_c); @@ -438,7 +441,8 @@ int start_dma_without_bch_irq(struct gpmi_nand_data *this, /* Wait for the interrupt from the DMA block. */ err = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000)); if (!err) { - pr_err("DMA timeout, last DMA :%d\n", this->last_dma_type); + dev_err(this->dev, "DMA timeout, last DMA :%d\n", + this->last_dma_type); gpmi_dump_info(this); return -ETIMEDOUT; } @@ -467,7 +471,8 @@ int start_dma_with_bch_irq(struct gpmi_nand_data *this, /* Wait for the interrupt from the BCH block. */ err = wait_for_completion_timeout(bch_c, msecs_to_jiffies(1000)); if (!err) { - pr_err("BCH timeout, last DMA :%d\n", this->last_dma_type); + dev_err(this->dev, "BCH timeout, last DMA :%d\n", + this->last_dma_type); gpmi_dump_info(this); return -ETIMEDOUT; } @@ -483,70 +488,38 @@ static int acquire_register_block(struct gpmi_nand_data *this, void __iomem *p; r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name); - if (!r) { - pr_err("Can't get resource for %s\n", res_name); - return -ENODEV; - } - - p = ioremap(r->start, resource_size(r)); - if (!p) { - pr_err("Can't remap %s\n", res_name); - return -ENOMEM; - } + p = devm_ioremap_resource(&pdev->dev, r); + if (IS_ERR(p)) + return PTR_ERR(p); if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME)) res->gpmi_regs = p; else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME)) res->bch_regs = p; else - pr_err("unknown resource name : %s\n", res_name); + dev_err(this->dev, "unknown resource name : %s\n", res_name); return 0; } -static void release_register_block(struct gpmi_nand_data *this) -{ - struct resources *res = &this->resources; - if (res->gpmi_regs) - iounmap(res->gpmi_regs); - if (res->bch_regs) - iounmap(res->bch_regs); - res->gpmi_regs = NULL; - res->bch_regs = NULL; -} - static int acquire_bch_irq(struct gpmi_nand_data *this, irq_handler_t irq_h) { struct platform_device *pdev = this->pdev; - struct resources *res = &this->resources; const char *res_name = GPMI_NAND_BCH_INTERRUPT_RES_NAME; struct resource *r; int err; r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, res_name); if (!r) { - pr_err("Can't get resource for %s\n", res_name); + dev_err(this->dev, "Can't get resource for %s\n", res_name); return -ENODEV; } - err = request_irq(r->start, irq_h, 0, res_name, this); - if (err) { - pr_err("Can't own %s\n", res_name); - return err; - } - - res->bch_low_interrupt = r->start; - res->bch_high_interrupt = r->end; - return 0; -} - -static void release_bch_irq(struct gpmi_nand_data *this) -{ - struct resources *res = &this->resources; - int i = res->bch_low_interrupt; + err = devm_request_irq(this->dev, r->start, irq_h, 0, res_name, this); + if (err) + dev_err(this->dev, "error requesting BCH IRQ\n"); - for (; i <= res->bch_high_interrupt; i++) - free_irq(i, this); + return err; } static void release_dma_channels(struct gpmi_nand_data *this) @@ -567,7 +540,7 @@ static int acquire_dma_channels(struct gpmi_nand_data *this) /* request dma channel */ dma_chan = dma_request_slave_channel(&pdev->dev, "rx-tx"); if (!dma_chan) { - pr_err("Failed to request DMA channel.\n"); + dev_err(this->dev, "Failed to request DMA channel.\n"); goto acquire_err; } @@ -579,21 +552,6 @@ acquire_err: return -EINVAL; } -static void gpmi_put_clks(struct gpmi_nand_data *this) -{ - struct resources *r = &this->resources; - struct clk *clk; - int i; - - for (i = 0; i < GPMI_CLK_MAX; i++) { - clk = r->clock[i]; - if (clk) { - clk_put(clk); - r->clock[i] = NULL; - } - } -} - static char *extra_clks_for_mx6q[GPMI_CLK_MAX] = { "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch", }; @@ -606,7 +564,7 @@ static int gpmi_get_clks(struct gpmi_nand_data *this) int err, i; /* The main clock is stored in the first. */ - r->clock[0] = clk_get(this->dev, "gpmi_io"); + r->clock[0] = devm_clk_get(this->dev, "gpmi_io"); if (IS_ERR(r->clock[0])) { err = PTR_ERR(r->clock[0]); goto err_clock; @@ -622,7 +580,7 @@ static int gpmi_get_clks(struct gpmi_nand_data *this) if (extra_clks[i - 1] == NULL) break; - clk = clk_get(this->dev, extra_clks[i - 1]); + clk = devm_clk_get(this->dev, extra_clks[i - 1]); if (IS_ERR(clk)) { err = PTR_ERR(clk); goto err_clock; @@ -644,7 +602,6 @@ static int gpmi_get_clks(struct gpmi_nand_data *this) err_clock: dev_dbg(this->dev, "failed in finding the clocks.\n"); - gpmi_put_clks(this); return err; } @@ -666,7 +623,7 @@ static int acquire_resources(struct gpmi_nand_data *this) ret = acquire_dma_channels(this); if (ret) - goto exit_dma_channels; + goto exit_regs; ret = gpmi_get_clks(this); if (ret) @@ -675,18 +632,12 @@ static int acquire_resources(struct gpmi_nand_data *this) exit_clock: release_dma_channels(this); -exit_dma_channels: - release_bch_irq(this); exit_regs: - release_register_block(this); return ret; } static void release_resources(struct gpmi_nand_data *this) { - gpmi_put_clks(this); - release_register_block(this); - release_bch_irq(this); release_dma_channels(this); } @@ -732,8 +683,7 @@ static int read_page_prepare(struct gpmi_nand_data *this, length, DMA_FROM_DEVICE); if (dma_mapping_error(dev, dest_phys)) { if (alt_size < length) { - pr_err("%s, Alternate buffer is too small\n", - __func__); + dev_err(dev, "Alternate buffer is too small\n"); return -ENOMEM; } goto map_failed; @@ -783,8 +733,7 @@ static int send_page_prepare(struct gpmi_nand_data *this, DMA_TO_DEVICE); if (dma_mapping_error(dev, source_phys)) { if (alt_size < length) { - pr_err("%s, Alternate buffer is too small\n", - __func__); + dev_err(dev, "Alternate buffer is too small\n"); return -ENOMEM; } goto map_failed; @@ -837,14 +786,23 @@ static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this) { struct bch_geometry *geo = &this->bch_geometry; struct device *dev = this->dev; + struct mtd_info *mtd = &this->mtd; /* [1] Allocate a command buffer. PAGE_SIZE is enough. */ this->cmd_buffer = kzalloc(PAGE_SIZE, GFP_DMA | GFP_KERNEL); if (this->cmd_buffer == NULL) goto error_alloc; - /* [2] Allocate a read/write data buffer. PAGE_SIZE is enough. */ - this->data_buffer_dma = kzalloc(PAGE_SIZE, GFP_DMA | GFP_KERNEL); + /* + * [2] Allocate a read/write data buffer. + * The gpmi_alloc_dma_buffer can be called twice. + * We allocate a PAGE_SIZE length buffer if gpmi_alloc_dma_buffer + * is called before the nand_scan_ident; and we allocate a buffer + * of the real NAND page size when the gpmi_alloc_dma_buffer is + * called after the nand_scan_ident. + */ + this->data_buffer_dma = kzalloc(mtd->writesize ?: PAGE_SIZE, + GFP_DMA | GFP_KERNEL); if (this->data_buffer_dma == NULL) goto error_alloc; @@ -872,7 +830,6 @@ static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this) error_alloc: gpmi_free_dma_buffer(this); - pr_err("Error allocating DMA buffers!\n"); return -ENOMEM; } @@ -904,7 +861,8 @@ static void gpmi_cmd_ctrl(struct mtd_info *mtd, int data, unsigned int ctrl) ret = gpmi_send_command(this); if (ret) - pr_err("Chip: %u, Error %d\n", this->current_chip, ret); + dev_err(this->dev, "Chip: %u, Error %d\n", + this->current_chip, ret); this->command_length = 0; } @@ -935,7 +893,7 @@ static void gpmi_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) struct nand_chip *chip = mtd->priv; struct gpmi_nand_data *this = chip->priv; - pr_debug("len is %d\n", len); + dev_dbg(this->dev, "len is %d\n", len); this->upper_buf = buf; this->upper_len = len; @@ -947,7 +905,7 @@ static void gpmi_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) struct nand_chip *chip = mtd->priv; struct gpmi_nand_data *this = chip->priv; - pr_debug("len is %d\n", len); + dev_dbg(this->dev, "len is %d\n", len); this->upper_buf = (uint8_t *)buf; this->upper_len = len; @@ -1026,13 +984,13 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, unsigned int max_bitflips = 0; int ret; - pr_debug("page number is : %d\n", page); + dev_dbg(this->dev, "page number is : %d\n", page); ret = read_page_prepare(this, buf, mtd->writesize, this->payload_virt, this->payload_phys, nfc_geo->payload_size, &payload_virt, &payload_phys); if (ret) { - pr_err("Inadequate DMA buffer\n"); + dev_err(this->dev, "Inadequate DMA buffer\n"); ret = -ENOMEM; return ret; } @@ -1046,7 +1004,7 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, nfc_geo->payload_size, payload_virt, payload_phys); if (ret) { - pr_err("Error in ECC-based read: %d\n", ret); + dev_err(this->dev, "Error in ECC-based read: %d\n", ret); return ret; } @@ -1102,7 +1060,7 @@ static int gpmi_ecc_write_page(struct mtd_info *mtd, struct nand_chip *chip, dma_addr_t auxiliary_phys; int ret; - pr_debug("ecc write page.\n"); + dev_dbg(this->dev, "ecc write page.\n"); if (this->swap_block_mark) { /* * If control arrives here, we're doing block mark swapping. @@ -1132,7 +1090,7 @@ static int gpmi_ecc_write_page(struct mtd_info *mtd, struct nand_chip *chip, nfc_geo->payload_size, &payload_virt, &payload_phys); if (ret) { - pr_err("Inadequate payload DMA buffer\n"); + dev_err(this->dev, "Inadequate payload DMA buffer\n"); return 0; } @@ -1142,7 +1100,7 @@ static int gpmi_ecc_write_page(struct mtd_info *mtd, struct nand_chip *chip, nfc_geo->auxiliary_size, &auxiliary_virt, &auxiliary_phys); if (ret) { - pr_err("Inadequate auxiliary DMA buffer\n"); + dev_err(this->dev, "Inadequate auxiliary DMA buffer\n"); goto exit_auxiliary; } } @@ -1150,7 +1108,7 @@ static int gpmi_ecc_write_page(struct mtd_info *mtd, struct nand_chip *chip, /* Ask the NFC. */ ret = gpmi_send_page(this, payload_phys, auxiliary_phys); if (ret) - pr_err("Error in ECC-based write: %d\n", ret); + dev_err(this->dev, "Error in ECC-based write: %d\n", ret); if (!this->swap_block_mark) { send_page_end(this, chip->oob_poi, mtd->oobsize, @@ -1240,7 +1198,7 @@ static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, { struct gpmi_nand_data *this = chip->priv; - pr_debug("page number is %d\n", page); + dev_dbg(this->dev, "page number is %d\n", page); /* clear the OOB buffer */ memset(chip->oob_poi, ~0, mtd->oobsize); @@ -1453,7 +1411,6 @@ static int mx23_write_transcription_stamp(struct gpmi_nand_data *this) /* Write the NCB fingerprint into the page buffer. */ memset(buffer, ~0, mtd->writesize); - memset(chip->oob_poi, ~0, mtd->oobsize); memcpy(buffer + 12, fingerprint, strlen(fingerprint)); /* Loop through the first search area, writing NCB fingerprints. */ @@ -1568,7 +1525,7 @@ static int gpmi_set_geometry(struct gpmi_nand_data *this) /* Set up the NFC geometry which is used by BCH. */ ret = bch_set_geometry(this); if (ret) { - pr_err("Error setting BCH geometry : %d\n", ret); + dev_err(this->dev, "Error setting BCH geometry : %d\n", ret); return ret; } @@ -1576,20 +1533,7 @@ static int gpmi_set_geometry(struct gpmi_nand_data *this) return gpmi_alloc_dma_buffer(this); } -static int gpmi_pre_bbt_scan(struct gpmi_nand_data *this) -{ - /* Set up swap_block_mark, must be set before the gpmi_set_geometry() */ - if (GPMI_IS_MX23(this)) - this->swap_block_mark = false; - else - this->swap_block_mark = true; - - /* Set up the medium geometry */ - return gpmi_set_geometry(this); - -} - -static void gpmi_nfc_exit(struct gpmi_nand_data *this) +static void gpmi_nand_exit(struct gpmi_nand_data *this) { nand_release(&this->mtd); gpmi_free_dma_buffer(this); @@ -1603,8 +1547,11 @@ static int gpmi_init_last(struct gpmi_nand_data *this) struct bch_geometry *bch_geo = &this->bch_geometry; int ret; - /* Prepare for the BBT scan. */ - ret = gpmi_pre_bbt_scan(this); + /* Set up swap_block_mark, must be set before the gpmi_set_geometry() */ + this->swap_block_mark = !GPMI_IS_MX23(this); + + /* Set up the medium geometry */ + ret = gpmi_set_geometry(this); if (ret) return ret; @@ -1629,7 +1576,7 @@ static int gpmi_init_last(struct gpmi_nand_data *this) return 0; } -static int gpmi_nfc_init(struct gpmi_nand_data *this) +static int gpmi_nand_init(struct gpmi_nand_data *this) { struct mtd_info *mtd = &this->mtd; struct nand_chip *chip = &this->nand; @@ -1693,7 +1640,7 @@ static int gpmi_nfc_init(struct gpmi_nand_data *this) return 0; err_out: - gpmi_nfc_exit(this); + gpmi_nand_exit(this); return ret; } @@ -1728,15 +1675,13 @@ static int gpmi_nand_probe(struct platform_device *pdev) if (of_id) { pdev->id_entry = of_id->data; } else { - pr_err("Failed to find the right device id.\n"); + dev_err(&pdev->dev, "Failed to find the right device id.\n"); return -ENODEV; } this = devm_kzalloc(&pdev->dev, sizeof(*this), GFP_KERNEL); - if (!this) { - pr_err("Failed to allocate per-device memory\n"); + if (!this) return -ENOMEM; - } platform_set_drvdata(pdev, this); this->pdev = pdev; @@ -1750,7 +1695,7 @@ static int gpmi_nand_probe(struct platform_device *pdev) if (ret) goto exit_nfc_init; - ret = gpmi_nfc_init(this); + ret = gpmi_nand_init(this); if (ret) goto exit_nfc_init; @@ -1770,7 +1715,7 @@ static int gpmi_nand_remove(struct platform_device *pdev) { struct gpmi_nand_data *this = platform_get_drvdata(pdev); - gpmi_nfc_exit(this); + gpmi_nand_exit(this); release_resources(this); return 0; } diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h index a7685e3..4c801fa 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h @@ -26,8 +26,6 @@ struct resources { void __iomem *gpmi_regs; void __iomem *bch_regs; - unsigned int bch_low_interrupt; - unsigned int bch_high_interrupt; unsigned int dma_low_channel; unsigned int dma_high_channel; struct clk *clock[GPMI_CLK_MAX]; diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/jz4740_nand.c index a264b88..a2c804d 100644 --- a/drivers/mtd/nand/jz4740_nand.c +++ b/drivers/mtd/nand/jz4740_nand.c @@ -416,10 +416,8 @@ static int jz_nand_probe(struct platform_device *pdev) uint8_t nand_maf_id = 0, nand_dev_id = 0; nand = kzalloc(sizeof(*nand), GFP_KERNEL); - if (!nand) { - dev_err(&pdev->dev, "Failed to allocate device structure.\n"); + if (!nand) return -ENOMEM; - } ret = jz_nand_ioremap_resource(pdev, "mmio", &nand->mem, &nand->base); if (ret) diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/lpc32xx_mlc.c index 327d96c..687478c 100644 --- a/drivers/mtd/nand/lpc32xx_mlc.c +++ b/drivers/mtd/nand/lpc32xx_mlc.c @@ -539,20 +539,6 @@ static int lpc32xx_write_page_lowlevel(struct mtd_info *mtd, return 0; } -static int lpc32xx_write_page(struct mtd_info *mtd, struct nand_chip *chip, - uint32_t offset, int data_len, const uint8_t *buf, - int oob_required, int page, int cached, int raw) -{ - int res; - - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); - res = lpc32xx_write_page_lowlevel(mtd, chip, buf, oob_required); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - lpc32xx_waitfunc(mtd, chip); - - return res; -} - static int lpc32xx_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { @@ -627,10 +613,8 @@ static struct lpc32xx_nand_cfg_mlc *lpc32xx_parse_dt(struct device *dev) struct device_node *np = dev->of_node; ncfg = devm_kzalloc(dev, sizeof(*ncfg), GFP_KERNEL); - if (!ncfg) { - dev_err(dev, "could not allocate memory for platform data\n"); + if (!ncfg) return NULL; - } of_property_read_u32(np, "nxp,tcea-delay", &ncfg->tcea_delay); of_property_read_u32(np, "nxp,busy-delay", &ncfg->busy_delay); @@ -666,10 +650,8 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) /* Allocate memory for the device structure (and zero it) */ host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); - if (!host) { - dev_err(&pdev->dev, "failed to allocate device structure.\n"); + if (!host) return -ENOMEM; - } rc = platform_get_resource(pdev, IORESOURCE_MEM, 0); host->io_base = devm_ioremap_resource(&pdev->dev, rc); @@ -732,9 +714,9 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) nand_chip->ecc.write_oob = lpc32xx_write_oob; nand_chip->ecc.read_oob = lpc32xx_read_oob; nand_chip->ecc.strength = 4; - nand_chip->write_page = lpc32xx_write_page; nand_chip->waitfunc = lpc32xx_waitfunc; + nand_chip->options = NAND_NO_SUBPAGE_WRITE; nand_chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB; nand_chip->bbt_td = &lpc32xx_nand_bbt; nand_chip->bbt_md = &lpc32xx_nand_bbt_mirror; @@ -764,14 +746,12 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) host->dma_buf = devm_kzalloc(&pdev->dev, mtd->writesize, GFP_KERNEL); if (!host->dma_buf) { - dev_err(&pdev->dev, "Error allocating dma_buf memory\n"); res = -ENOMEM; goto err_exit3; } host->dummy_buf = devm_kzalloc(&pdev->dev, mtd->writesize, GFP_KERNEL); if (!host->dummy_buf) { - dev_err(&pdev->dev, "Error allocating dummy_buf memory\n"); res = -ENOMEM; goto err_exit3; } diff --git a/drivers/mtd/nand/lpc32xx_slc.c b/drivers/mtd/nand/lpc32xx_slc.c index 23e6974..53a6742 100644 --- a/drivers/mtd/nand/lpc32xx_slc.c +++ b/drivers/mtd/nand/lpc32xx_slc.c @@ -725,10 +725,8 @@ static struct lpc32xx_nand_cfg_slc *lpc32xx_parse_dt(struct device *dev) struct device_node *np = dev->of_node; ncfg = devm_kzalloc(dev, sizeof(*ncfg), GFP_KERNEL); - if (!ncfg) { - dev_err(dev, "could not allocate memory for NAND config\n"); + if (!ncfg) return NULL; - } of_property_read_u32(np, "nxp,wdr-clks", &ncfg->wdr_clks); of_property_read_u32(np, "nxp,wwidth", &ncfg->wwidth); @@ -772,10 +770,8 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) /* Allocate memory for the device structure (and zero it) */ host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL); - if (!host) { - dev_err(&pdev->dev, "failed to allocate device structure\n"); + if (!host) return -ENOMEM; - } host->io_base_dma = rc->start; host->io_base = devm_ioremap_resource(&pdev->dev, rc); @@ -791,8 +787,8 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) } if (host->ncfg->wp_gpio == -EPROBE_DEFER) return -EPROBE_DEFER; - if (gpio_is_valid(host->ncfg->wp_gpio) && - gpio_request(host->ncfg->wp_gpio, "NAND WP")) { + if (gpio_is_valid(host->ncfg->wp_gpio) && devm_gpio_request(&pdev->dev, + host->ncfg->wp_gpio, "NAND WP")) { dev_err(&pdev->dev, "GPIO not available\n"); return -EBUSY; } @@ -808,7 +804,7 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) mtd->dev.parent = &pdev->dev; /* Get NAND clock */ - host->clk = clk_get(&pdev->dev, NULL); + host->clk = devm_clk_get(&pdev->dev, NULL); if (IS_ERR(host->clk)) { dev_err(&pdev->dev, "Clock failure\n"); res = -ENOENT; @@ -858,7 +854,6 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) host->data_buf = devm_kzalloc(&pdev->dev, host->dma_buf_len, GFP_KERNEL); if (host->data_buf == NULL) { - dev_err(&pdev->dev, "Error allocating memory\n"); res = -ENOMEM; goto err_exit2; } @@ -927,10 +922,8 @@ err_exit3: dma_release_channel(host->dma_chan); err_exit2: clk_disable(host->clk); - clk_put(host->clk); err_exit1: lpc32xx_wp_enable(host); - gpio_free(host->ncfg->wp_gpio); return res; } @@ -953,9 +946,7 @@ static int lpc32xx_nand_remove(struct platform_device *pdev) writel(tmp, SLC_CTRL(host->io_base)); clk_disable(host->clk); - clk_put(host->clk); lpc32xx_wp_enable(host); - gpio_free(host->ncfg->wp_gpio); return 0; } diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/mpc5121_nfc.c index 439bc38..61e2abc 100644 --- a/drivers/mtd/nand/mpc5121_nfc.c +++ b/drivers/mtd/nand/mpc5121_nfc.c @@ -653,10 +653,8 @@ static int mpc5121_nfc_probe(struct platform_device *op) } prv = devm_kzalloc(dev, sizeof(*prv), GFP_KERNEL); - if (!prv) { - dev_err(dev, "Memory exhausted!\n"); + if (!prv) return -ENOMEM; - } mtd = &prv->mtd; chip = &prv->chip; @@ -786,7 +784,6 @@ static int mpc5121_nfc_probe(struct platform_device *op) /* Detect NAND chips */ if (nand_scan(mtd, be32_to_cpup(chips_no))) { dev_err(dev, "NAND Flash not found !\n"); - devm_free_irq(dev, prv->irq, mtd); retval = -ENXIO; goto error; } @@ -811,7 +808,6 @@ static int mpc5121_nfc_probe(struct platform_device *op) default: dev_err(dev, "Unsupported NAND flash!\n"); - devm_free_irq(dev, prv->irq, mtd); retval = -ENXIO; goto error; } @@ -822,7 +818,6 @@ static int mpc5121_nfc_probe(struct platform_device *op) retval = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); if (retval) { dev_err(dev, "Error adding MTD device!\n"); - devm_free_irq(dev, prv->irq, mtd); goto error; } @@ -836,11 +831,8 @@ static int mpc5121_nfc_remove(struct platform_device *op) { struct device *dev = &op->dev; struct mtd_info *mtd = dev_get_drvdata(dev); - struct nand_chip *chip = mtd->priv; - struct mpc5121_nfc_prv *prv = chip->priv; nand_release(mtd); - devm_free_irq(dev, prv->irq, mtd); mpc5121_nfc_free(dev, mtd); return 0; diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c index 9dfdb06..e9a4835 100644 --- a/drivers/mtd/nand/mxc_nand.c +++ b/drivers/mtd/nand/mxc_nand.c @@ -677,7 +677,6 @@ static int mxc_nand_correct_data_v2_v3(struct mtd_info *mtd, u_char *dat, ecc_stat >>= 4; } while (--no_subpages); - mtd->ecc_stats.corrected += ret; pr_debug("%d Symbol Correctable RS-ECC Error\n", ret); return ret; @@ -1400,12 +1399,15 @@ static int mxcnd_probe(struct platform_device *pdev) int err = 0; /* Allocate memory for MTD device structure and private data */ - host = devm_kzalloc(&pdev->dev, sizeof(struct mxc_nand_host) + - NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE, GFP_KERNEL); + host = devm_kzalloc(&pdev->dev, sizeof(struct mxc_nand_host), + GFP_KERNEL); if (!host) return -ENOMEM; - host->data_buf = (uint8_t *)(host + 1); + /* allocate a temporary buffer for the nand_scan_ident() */ + host->data_buf = devm_kzalloc(&pdev->dev, PAGE_SIZE, GFP_KERNEL); + if (!host->data_buf) + return -ENOMEM; host->dev = &pdev->dev; /* structures must be linked */ @@ -1512,7 +1514,9 @@ static int mxcnd_probe(struct platform_device *pdev) if (err) return err; - clk_prepare_enable(host->clk); + err = clk_prepare_enable(host->clk); + if (err) + return err; host->clk_act = 1; /* @@ -1531,6 +1535,15 @@ static int mxcnd_probe(struct platform_device *pdev) goto escan; } + /* allocate the right size buffer now */ + devm_kfree(&pdev->dev, (void *)host->data_buf); + host->data_buf = devm_kzalloc(&pdev->dev, mtd->writesize + mtd->oobsize, + GFP_KERNEL); + if (!host->data_buf) { + err = -ENOMEM; + goto escan; + } + /* Call preset again, with correct writesize this time */ host->devtype_data->preset(mtd); @@ -1576,6 +1589,8 @@ static int mxcnd_remove(struct platform_device *pdev) struct mxc_nand_host *host = platform_get_drvdata(pdev); nand_release(&host->mtd); + if (host->clk_act) + clk_disable_unprepare(host->clk); return 0; } diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index bd39f7b..59eba5d 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -29,6 +29,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/module.h> #include <linux/delay.h> #include <linux/errno.h> @@ -202,6 +204,51 @@ static void nand_select_chip(struct mtd_info *mtd, int chipnr) } /** + * nand_write_byte - [DEFAULT] write single byte to chip + * @mtd: MTD device structure + * @byte: value to write + * + * Default function to write a byte to I/O[7:0] + */ +static void nand_write_byte(struct mtd_info *mtd, uint8_t byte) +{ + struct nand_chip *chip = mtd->priv; + + chip->write_buf(mtd, &byte, 1); +} + +/** + * nand_write_byte16 - [DEFAULT] write single byte to a chip with width 16 + * @mtd: MTD device structure + * @byte: value to write + * + * Default function to write a byte to I/O[7:0] on a 16-bit wide chip. + */ +static void nand_write_byte16(struct mtd_info *mtd, uint8_t byte) +{ + struct nand_chip *chip = mtd->priv; + uint16_t word = byte; + + /* + * It's not entirely clear what should happen to I/O[15:8] when writing + * a byte. The ONFi spec (Revision 3.1; 2012-09-19, Section 2.16) reads: + * + * When the host supports a 16-bit bus width, only data is + * transferred at the 16-bit width. All address and command line + * transfers shall use only the lower 8-bits of the data bus. During + * command transfers, the host may place any value on the upper + * 8-bits of the data bus. During address transfers, the host shall + * set the upper 8-bits of the data bus to 00h. + * + * One user of the write_byte callback is nand_onfi_set_features. The + * four parameters are specified to be written to I/O[7:0], but this is + * neither an address nor a command transfer. Let's assume a 0 on the + * upper I/O lines is OK. + */ + chip->write_buf(mtd, (uint8_t *)&word, 2); +} + +/** * nand_write_buf - [DEFAULT] write buffer to chip * @mtd: MTD device structure * @buf: data buffer @@ -1408,6 +1455,30 @@ static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob, } /** + * nand_setup_read_retry - [INTERN] Set the READ RETRY mode + * @mtd: MTD device structure + * @retry_mode: the retry mode to use + * + * Some vendors supply a special command to shift the Vt threshold, to be used + * when there are too many bitflips in a page (i.e., ECC error). After setting + * a new threshold, the host should retry reading the page. + */ +static int nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) +{ + struct nand_chip *chip = mtd->priv; + + pr_debug("setting READ RETRY mode %d\n", retry_mode); + + if (retry_mode >= chip->read_retries) + return -EINVAL; + + if (!chip->setup_read_retry) + return -EOPNOTSUPP; + + return chip->setup_read_retry(mtd, retry_mode); +} + +/** * nand_do_read_ops - [INTERN] Read data with ECC * @mtd: MTD device structure * @from: offset to read from @@ -1420,7 +1491,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, { int chipnr, page, realpage, col, bytes, aligned, oob_required; struct nand_chip *chip = mtd->priv; - struct mtd_ecc_stats stats; int ret = 0; uint32_t readlen = ops->len; uint32_t oobreadlen = ops->ooblen; @@ -1429,8 +1499,8 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, uint8_t *bufpoi, *oob, *buf; unsigned int max_bitflips = 0; - - stats = mtd->ecc_stats; + int retry_mode = 0; + bool ecc_fail = false; chipnr = (int)(from >> chip->chip_shift); chip->select_chip(mtd, chipnr); @@ -1445,6 +1515,8 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, oob_required = oob ? 1 : 0; while (1) { + unsigned int ecc_failures = mtd->ecc_stats.failed; + bytes = min(mtd->writesize - col, readlen); aligned = (bytes == mtd->writesize); @@ -1452,6 +1524,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, if (realpage != chip->pagebuf || oob) { bufpoi = aligned ? buf : chip->buffers->databuf; +read_retry: chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); /* @@ -1481,7 +1554,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, /* Transfer not aligned data */ if (!aligned) { if (!NAND_HAS_SUBPAGE_READ(chip) && !oob && - !(mtd->ecc_stats.failed - stats.failed) && + !(mtd->ecc_stats.failed - ecc_failures) && (ops->mode != MTD_OPS_RAW)) { chip->pagebuf = realpage; chip->pagebuf_bitflips = ret; @@ -1492,8 +1565,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, memcpy(buf, chip->buffers->databuf + col, bytes); } - buf += bytes; - if (unlikely(oob)) { int toread = min(oobreadlen, max_oobsize); @@ -1511,6 +1582,25 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, else nand_wait_ready(mtd); } + + if (mtd->ecc_stats.failed - ecc_failures) { + if (retry_mode + 1 <= chip->read_retries) { + retry_mode++; + ret = nand_setup_read_retry(mtd, + retry_mode); + if (ret < 0) + break; + + /* Reset failures; retry */ + mtd->ecc_stats.failed = ecc_failures; + goto read_retry; + } else { + /* No more retry modes; real failure */ + ecc_fail = true; + } + } + + buf += bytes; } else { memcpy(buf, chip->buffers->databuf + col, bytes); buf += bytes; @@ -1520,6 +1610,14 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, readlen -= bytes; + /* Reset to retry mode 0 */ + if (retry_mode) { + ret = nand_setup_read_retry(mtd, 0); + if (ret < 0) + break; + retry_mode = 0; + } + if (!readlen) break; @@ -1545,7 +1643,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, if (ret < 0) return ret; - if (mtd->ecc_stats.failed - stats.failed) + if (ecc_fail) return -EBADMSG; return max_bitflips; @@ -2716,6 +2814,7 @@ static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, int addr, uint8_t *subfeature_param) { int status; + int i; if (!chip->onfi_version || !(le16_to_cpu(chip->onfi_params.opt_cmd) @@ -2723,7 +2822,9 @@ static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, return -EINVAL; chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, addr, -1); - chip->write_buf(mtd, subfeature_param, ONFI_SUBFEATURE_PARAM_LEN); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + chip->write_byte(mtd, subfeature_param[i]); + status = chip->waitfunc(mtd, chip); if (status & NAND_STATUS_FAIL) return -EIO; @@ -2740,6 +2841,8 @@ static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip, int addr, uint8_t *subfeature_param) { + int i; + if (!chip->onfi_version || !(le16_to_cpu(chip->onfi_params.opt_cmd) & ONFI_OPT_CMD_SET_GET_FEATURES)) @@ -2749,7 +2852,8 @@ static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip, memset(subfeature_param, 0, ONFI_SUBFEATURE_PARAM_LEN); chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, addr, -1); - chip->read_buf(mtd, subfeature_param, ONFI_SUBFEATURE_PARAM_LEN); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + *subfeature_param++ = chip->read_byte(mtd); return 0; } @@ -2812,6 +2916,8 @@ static void nand_set_defaults(struct nand_chip *chip, int busw) chip->block_markbad = nand_default_block_markbad; if (!chip->write_buf || chip->write_buf == nand_write_buf) chip->write_buf = busw ? nand_write_buf16 : nand_write_buf; + if (!chip->write_byte || chip->write_byte == nand_write_byte) + chip->write_byte = busw ? nand_write_byte16 : nand_write_byte; if (!chip->read_buf || chip->read_buf == nand_read_buf) chip->read_buf = busw ? nand_read_buf16 : nand_read_buf; if (!chip->scan_bbt) @@ -2926,6 +3032,30 @@ ext_out: return ret; } +static int nand_setup_read_retry_micron(struct mtd_info *mtd, int retry_mode) +{ + struct nand_chip *chip = mtd->priv; + uint8_t feature[ONFI_SUBFEATURE_PARAM_LEN] = {retry_mode}; + + return chip->onfi_set_features(mtd, chip, ONFI_FEATURE_ADDR_READ_RETRY, + feature); +} + +/* + * Configure chip properties from Micron vendor-specific ONFI table + */ +static void nand_onfi_detect_micron(struct nand_chip *chip, + struct nand_onfi_params *p) +{ + struct nand_onfi_vendor_micron *micron = (void *)p->vendor; + + if (le16_to_cpu(p->vendor_revision) < 1) + return; + + chip->read_retries = micron->read_retry_options; + chip->setup_read_retry = nand_setup_read_retry_micron; +} + /* * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise. */ @@ -2979,7 +3109,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, chip->onfi_version = 10; if (!chip->onfi_version) { - pr_info("%s: unsupported ONFI version: %d\n", __func__, val); + pr_info("unsupported ONFI version: %d\n", val); return 0; } @@ -3032,6 +3162,9 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip, pr_warn("Could not retrieve ONFI ECC requirements\n"); } + if (p->jedec_id == NAND_MFR_MICRON) + nand_onfi_detect_micron(chip, p); + return 1; } @@ -3152,9 +3285,12 @@ static void nand_decode_ext_id(struct mtd_info *mtd, struct nand_chip *chip, mtd->oobsize = 512; break; case 6: - default: /* Other cases are "reserved" (unknown) */ mtd->oobsize = 640; break; + case 7: + default: /* Other cases are "reserved" (unknown) */ + mtd->oobsize = 1024; + break; } extid >>= 2; /* Calc blocksize */ @@ -3325,6 +3461,9 @@ static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip, *busw = type->options & NAND_BUSWIDTH_16; + if (!mtd->name) + mtd->name = type->name; + return true; } return false; @@ -3372,8 +3511,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, id_data[i] = chip->read_byte(mtd); if (id_data[0] != *maf_id || id_data[1] != *dev_id) { - pr_info("%s: second ID read did not match " - "%02x,%02x against %02x,%02x\n", __func__, + pr_info("second ID read did not match %02x,%02x against %02x,%02x\n", *maf_id, *dev_id, id_data[0], id_data[1]); return ERR_PTR(-ENODEV); } @@ -3440,10 +3578,10 @@ ident_done: * Check, if buswidth is correct. Hardware drivers should set * chip correct! */ - pr_info("NAND device: Manufacturer ID:" - " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, - *dev_id, nand_manuf_ids[maf_idx].name, mtd->name); - pr_warn("NAND bus width %d instead %d bit\n", + pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n", + *maf_id, *dev_id); + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, mtd->name); + pr_warn("bus width %d instead %d bit\n", (chip->options & NAND_BUSWIDTH_16) ? 16 : 8, busw ? 16 : 8); return ERR_PTR(-EINVAL); @@ -3472,14 +3610,13 @@ ident_done: if (mtd->writesize > 512 && chip->cmdfunc == nand_command) chip->cmdfunc = nand_command_lp; - pr_info("NAND device: Manufacturer ID: 0x%02x, Chip ID: 0x%02x (%s %s)\n", - *maf_id, *dev_id, nand_manuf_ids[maf_idx].name, + pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n", + *maf_id, *dev_id); + pr_info("%s %s\n", nand_manuf_ids[maf_idx].name, chip->onfi_version ? chip->onfi_params.model : type->name); - - pr_info("NAND device: %dMiB, %s, page size: %d, OOB size: %d\n", + pr_info("%dMiB, %s, page size: %d, OOB size: %d\n", (int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC", mtd->writesize, mtd->oobsize); - return type; } @@ -3535,7 +3672,7 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, chip->select_chip(mtd, -1); } if (i > 1) - pr_info("%d NAND chips detected\n", i); + pr_info("%d chips detected\n", i); /* Store the number of chips and calc total size for mtd */ chip->numchips = i; diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/nand_ids.c index a87b0a3..daa2faa 100644 --- a/drivers/mtd/nand/nand_ids.c +++ b/drivers/mtd/nand/nand_ids.c @@ -169,6 +169,8 @@ struct nand_manufacturers nand_manuf_ids[] = { {NAND_MFR_AMD, "AMD/Spansion"}, {NAND_MFR_MACRONIX, "Macronix"}, {NAND_MFR_EON, "Eon"}, + {NAND_MFR_SANDISK, "SanDisk"}, + {NAND_MFR_INTEL, "Intel"}, {0x0, "Unknown"} }; diff --git a/drivers/mtd/nand/nuc900_nand.c b/drivers/mtd/nand/nuc900_nand.c index 5211515..9ee09a8 100644 --- a/drivers/mtd/nand/nuc900_nand.c +++ b/drivers/mtd/nand/nuc900_nand.c @@ -241,12 +241,10 @@ static int nuc900_nand_probe(struct platform_device *pdev) { struct nuc900_nand *nuc900_nand; struct nand_chip *chip; - int retval; struct resource *res; - retval = 0; - - nuc900_nand = kzalloc(sizeof(struct nuc900_nand), GFP_KERNEL); + nuc900_nand = devm_kzalloc(&pdev->dev, sizeof(struct nuc900_nand), + GFP_KERNEL); if (!nuc900_nand) return -ENOMEM; chip = &(nuc900_nand->chip); @@ -255,11 +253,9 @@ static int nuc900_nand_probe(struct platform_device *pdev) nuc900_nand->mtd.owner = THIS_MODULE; spin_lock_init(&nuc900_nand->lock); - nuc900_nand->clk = clk_get(&pdev->dev, NULL); - if (IS_ERR(nuc900_nand->clk)) { - retval = -ENOENT; - goto fail1; - } + nuc900_nand->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(nuc900_nand->clk)) + return -ENOENT; clk_enable(nuc900_nand->clk); chip->cmdfunc = nuc900_nand_command_lp; @@ -272,57 +268,29 @@ static int nuc900_nand_probe(struct platform_device *pdev) chip->ecc.mode = NAND_ECC_SOFT; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) { - retval = -ENXIO; - goto fail1; - } - - if (!request_mem_region(res->start, resource_size(res), pdev->name)) { - retval = -EBUSY; - goto fail1; - } - - nuc900_nand->reg = ioremap(res->start, resource_size(res)); - if (!nuc900_nand->reg) { - retval = -ENOMEM; - goto fail2; - } + nuc900_nand->reg = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(nuc900_nand->reg)) + return PTR_ERR(nuc900_nand->reg); nuc900_nand_enable(nuc900_nand); - if (nand_scan(&(nuc900_nand->mtd), 1)) { - retval = -ENXIO; - goto fail3; - } + if (nand_scan(&(nuc900_nand->mtd), 1)) + return -ENXIO; mtd_device_register(&(nuc900_nand->mtd), partitions, ARRAY_SIZE(partitions)); platform_set_drvdata(pdev, nuc900_nand); - return retval; - -fail3: iounmap(nuc900_nand->reg); -fail2: release_mem_region(res->start, resource_size(res)); -fail1: kfree(nuc900_nand); - return retval; + return 0; } static int nuc900_nand_remove(struct platform_device *pdev) { struct nuc900_nand *nuc900_nand = platform_get_drvdata(pdev); - struct resource *res; nand_release(&nuc900_nand->mtd); - iounmap(nuc900_nand->reg); - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - release_mem_region(res->start, resource_size(res)); - clk_disable(nuc900_nand->clk); - clk_put(nuc900_nand->clk); - - kfree(nuc900_nand); return 0; } diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index f777250..ef4190a 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -1730,13 +1730,7 @@ static int omap_nand_probe(struct platform_device *pdev) break; case NAND_OMAP_POLLED: - if (nand_chip->options & NAND_BUSWIDTH_16) { - nand_chip->read_buf = omap_read_buf16; - nand_chip->write_buf = omap_write_buf16; - } else { - nand_chip->read_buf = omap_read_buf8; - nand_chip->write_buf = omap_write_buf8; - } + /* Use nand_base defaults for {read,write}_buf */ break; case NAND_OMAP_PREFETCH_DMA: diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c index a393a5b..dd7fe81 100644 --- a/drivers/mtd/nand/orion_nand.c +++ b/drivers/mtd/nand/orion_nand.c @@ -87,7 +87,6 @@ static int __init orion_nand_probe(struct platform_device *pdev) nc = kzalloc(sizeof(struct nand_chip) + sizeof(struct mtd_info), GFP_KERNEL); if (!nc) { - printk(KERN_ERR "orion_nand: failed to allocate device structure.\n"); ret = -ENOMEM; goto no_res; } @@ -101,7 +100,7 @@ static int __init orion_nand_probe(struct platform_device *pdev) io_base = ioremap(res->start, resource_size(res)); if (!io_base) { - printk(KERN_ERR "orion_nand: ioremap failed\n"); + dev_err(&pdev->dev, "ioremap failed\n"); ret = -EIO; goto no_res; } @@ -110,7 +109,6 @@ static int __init orion_nand_probe(struct platform_device *pdev) board = devm_kzalloc(&pdev->dev, sizeof(struct orion_nand_data), GFP_KERNEL); if (!board) { - printk(KERN_ERR "orion_nand: failed to allocate board structure.\n"); ret = -ENOMEM; goto no_res; } diff --git a/drivers/mtd/nand/pasemi_nand.c b/drivers/mtd/nand/pasemi_nand.c index 4d17436..90f871a 100644 --- a/drivers/mtd/nand/pasemi_nand.c +++ b/drivers/mtd/nand/pasemi_nand.c @@ -223,7 +223,7 @@ MODULE_DEVICE_TABLE(of, pasemi_nand_match); static struct platform_driver pasemi_nand_driver = { .driver = { - .name = (char*)driver_name, + .name = driver_name, .owner = THIS_MODULE, .of_match_table = pasemi_nand_match, }, diff --git a/drivers/mtd/nand/plat_nand.c b/drivers/mtd/nand/plat_nand.c index cad4cdc..0b068a5 100644 --- a/drivers/mtd/nand/plat_nand.c +++ b/drivers/mtd/nand/plat_nand.c @@ -9,6 +9,7 @@ * */ +#include <linux/err.h> #include <linux/io.h> #include <linux/module.h> #include <linux/platform_device.h> @@ -47,30 +48,16 @@ static int plat_nand_probe(struct platform_device *pdev) return -EINVAL; } - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) - return -ENXIO; - /* Allocate memory for the device structure (and zero it) */ - data = kzalloc(sizeof(struct plat_nand_data), GFP_KERNEL); - if (!data) { - dev_err(&pdev->dev, "failed to allocate device structure.\n"); + data = devm_kzalloc(&pdev->dev, sizeof(struct plat_nand_data), + GFP_KERNEL); + if (!data) return -ENOMEM; - } - - if (!request_mem_region(res->start, resource_size(res), - dev_name(&pdev->dev))) { - dev_err(&pdev->dev, "request_mem_region failed\n"); - err = -EBUSY; - goto out_free; - } - data->io_base = ioremap(res->start, resource_size(res)); - if (data->io_base == NULL) { - dev_err(&pdev->dev, "ioremap failed\n"); - err = -EIO; - goto out_release_io; - } + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + data->io_base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(data->io_base)) + return PTR_ERR(data->io_base); data->chip.priv = &data; data->mtd.priv = &data->chip; @@ -122,11 +109,6 @@ static int plat_nand_probe(struct platform_device *pdev) out: if (pdata->ctrl.remove) pdata->ctrl.remove(pdev); - iounmap(data->io_base); -out_release_io: - release_mem_region(res->start, resource_size(res)); -out_free: - kfree(data); return err; } @@ -137,16 +119,10 @@ static int plat_nand_remove(struct platform_device *pdev) { struct plat_nand_data *data = platform_get_drvdata(pdev); struct platform_nand_data *pdata = dev_get_platdata(&pdev->dev); - struct resource *res; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); nand_release(&data->mtd); if (pdata->ctrl.remove) pdata->ctrl.remove(pdev); - iounmap(data->io_base); - release_mem_region(res->start, resource_size(res)); - kfree(data); return 0; } diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c index 4b3aaa8..2a7a0b2 100644 --- a/drivers/mtd/nand/pxa3xx_nand.c +++ b/drivers/mtd/nand/pxa3xx_nand.c @@ -7,6 +7,8 @@ * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. + * + * See Documentation/mtd/nand/pxa3xx-nand.txt for more details. */ #include <linux/kernel.h> @@ -24,6 +26,7 @@ #include <linux/slab.h> #include <linux/of.h> #include <linux/of_device.h> +#include <linux/of_mtd.h> #if defined(CONFIG_ARCH_PXA) || defined(CONFIG_ARCH_MMP) #define ARCH_HAS_DMA @@ -35,6 +38,7 @@ #include <linux/platform_data/mtd-nand-pxa3xx.h> +#define NAND_DEV_READY_TIMEOUT 50 #define CHIP_DELAY_TIMEOUT (2 * HZ/10) #define NAND_STOP_DELAY (2 * HZ/50) #define PAGE_CHUNK_SIZE (2048) @@ -54,6 +58,7 @@ #define NDPCR (0x18) /* Page Count Register */ #define NDBDR0 (0x1C) /* Bad Block Register 0 */ #define NDBDR1 (0x20) /* Bad Block Register 1 */ +#define NDECCCTRL (0x28) /* ECC control */ #define NDDB (0x40) /* Data Buffer */ #define NDCB0 (0x48) /* Command Buffer0 */ #define NDCB1 (0x4C) /* Command Buffer1 */ @@ -80,6 +85,9 @@ #define NDCR_INT_MASK (0xFFF) #define NDSR_MASK (0xfff) +#define NDSR_ERR_CNT_OFF (16) +#define NDSR_ERR_CNT_MASK (0x1f) +#define NDSR_ERR_CNT(sr) ((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK) #define NDSR_RDY (0x1 << 12) #define NDSR_FLASH_RDY (0x1 << 11) #define NDSR_CS0_PAGED (0x1 << 10) @@ -88,8 +96,8 @@ #define NDSR_CS1_CMDD (0x1 << 7) #define NDSR_CS0_BBD (0x1 << 6) #define NDSR_CS1_BBD (0x1 << 5) -#define NDSR_DBERR (0x1 << 4) -#define NDSR_SBERR (0x1 << 3) +#define NDSR_UNCORERR (0x1 << 4) +#define NDSR_CORERR (0x1 << 3) #define NDSR_WRDREQ (0x1 << 2) #define NDSR_RDDREQ (0x1 << 1) #define NDSR_WRCMDREQ (0x1) @@ -98,6 +106,8 @@ #define NDCB0_ST_ROW_EN (0x1 << 26) #define NDCB0_AUTO_RS (0x1 << 25) #define NDCB0_CSEL (0x1 << 24) +#define NDCB0_EXT_CMD_TYPE_MASK (0x7 << 29) +#define NDCB0_EXT_CMD_TYPE(x) (((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK) #define NDCB0_CMD_TYPE_MASK (0x7 << 21) #define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK) #define NDCB0_NC (0x1 << 20) @@ -108,6 +118,14 @@ #define NDCB0_CMD1_MASK (0xff) #define NDCB0_ADDR_CYC_SHIFT (16) +#define EXT_CMD_TYPE_DISPATCH 6 /* Command dispatch */ +#define EXT_CMD_TYPE_NAKED_RW 5 /* Naked read or Naked write */ +#define EXT_CMD_TYPE_READ 4 /* Read */ +#define EXT_CMD_TYPE_DISP_WR 4 /* Command dispatch with write */ +#define EXT_CMD_TYPE_FINAL 3 /* Final command */ +#define EXT_CMD_TYPE_LAST_RW 1 /* Last naked read/write */ +#define EXT_CMD_TYPE_MONO 0 /* Monolithic read/write */ + /* macros for registers read/write */ #define nand_writel(info, off, val) \ __raw_writel((val), (info)->mmio_base + (off)) @@ -120,9 +138,9 @@ enum { ERR_NONE = 0, ERR_DMABUSERR = -1, ERR_SENDCMD = -2, - ERR_DBERR = -3, + ERR_UNCORERR = -3, ERR_BBERR = -4, - ERR_SBERR = -5, + ERR_CORERR = -5, }; enum { @@ -149,7 +167,6 @@ struct pxa3xx_nand_host { void *info_data; /* page size of attached chip */ - unsigned int page_size; int use_ecc; int cs; @@ -167,11 +184,13 @@ struct pxa3xx_nand_info { struct clk *clk; void __iomem *mmio_base; unsigned long mmio_phys; - struct completion cmd_complete; + struct completion cmd_complete, dev_ready; unsigned int buf_start; unsigned int buf_count; unsigned int buf_size; + unsigned int data_buff_pos; + unsigned int oob_buff_pos; /* DMA information */ int drcmr_dat; @@ -195,13 +214,18 @@ struct pxa3xx_nand_info { int cs; int use_ecc; /* use HW ECC ? */ + int ecc_bch; /* using BCH ECC? */ int use_dma; /* use DMA ? */ int use_spare; /* use spare ? */ - int is_ready; + int need_wait; - unsigned int page_size; /* page size of attached chip */ - unsigned int data_size; /* data size in FIFO */ + unsigned int data_size; /* data to be read from FIFO */ + unsigned int chunk_size; /* split commands chunk size */ unsigned int oob_size; + unsigned int spare_size; + unsigned int ecc_size; + unsigned int ecc_err_cnt; + unsigned int max_bitflips; int retcode; /* cached register value */ @@ -239,6 +263,64 @@ static struct pxa3xx_nand_flash builtin_flash_types[] = { { "256MiB 16-bit", 0xba20, 64, 2048, 16, 16, 2048, &timing[3] }, }; +static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' }; +static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 8, + .len = 6, + .veroffs = 14, + .maxblocks = 8, /* Last 8 blocks in each chip */ + .pattern = bbt_pattern +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE + | NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 8, + .len = 6, + .veroffs = 14, + .maxblocks = 8, /* Last 8 blocks in each chip */ + .pattern = bbt_mirror_pattern +}; + +static struct nand_ecclayout ecc_layout_2KB_bch4bit = { + .eccbytes = 32, + .eccpos = { + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63}, + .oobfree = { {2, 30} } +}; + +static struct nand_ecclayout ecc_layout_4KB_bch4bit = { + .eccbytes = 64, + .eccpos = { + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63, + 96, 97, 98, 99, 100, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 124, 125, 126, 127}, + /* Bootrom looks in bytes 0 & 5 for bad blocks */ + .oobfree = { {6, 26}, { 64, 32} } +}; + +static struct nand_ecclayout ecc_layout_4KB_bch8bit = { + .eccbytes = 128, + .eccpos = { + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63}, + .oobfree = { } +}; + /* Define a default flash type setting serve as flash detecting only */ #define DEFAULT_FLASH_TYPE (&builtin_flash_types[0]) @@ -256,6 +338,29 @@ static struct pxa3xx_nand_flash builtin_flash_types[] = { /* convert nano-seconds to nand flash controller clock cycles */ #define ns2cycle(ns, clk) (int)((ns) * (clk / 1000000) / 1000) +static struct of_device_id pxa3xx_nand_dt_ids[] = { + { + .compatible = "marvell,pxa3xx-nand", + .data = (void *)PXA3XX_NAND_VARIANT_PXA, + }, + { + .compatible = "marvell,armada370-nand", + .data = (void *)PXA3XX_NAND_VARIANT_ARMADA370, + }, + {} +}; +MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids); + +static enum pxa3xx_nand_variant +pxa3xx_nand_get_variant(struct platform_device *pdev) +{ + const struct of_device_id *of_id = + of_match_device(pxa3xx_nand_dt_ids, &pdev->dev); + if (!of_id) + return PXA3XX_NAND_VARIANT_PXA; + return (enum pxa3xx_nand_variant)of_id->data; +} + static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host, const struct pxa3xx_nand_timing *t) { @@ -280,25 +385,23 @@ static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host, nand_writel(info, NDTR1CS0, ndtr1); } -static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info) +/* + * Set the data and OOB size, depending on the selected + * spare and ECC configuration. + * Only applicable to READ0, READOOB and PAGEPROG commands. + */ +static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info, + struct mtd_info *mtd) { - struct pxa3xx_nand_host *host = info->host[info->cs]; int oob_enable = info->reg_ndcr & NDCR_SPARE_EN; - info->data_size = host->page_size; - if (!oob_enable) { - info->oob_size = 0; + info->data_size = mtd->writesize; + if (!oob_enable) return; - } - switch (host->page_size) { - case 2048: - info->oob_size = (info->use_ecc) ? 40 : 64; - break; - case 512: - info->oob_size = (info->use_ecc) ? 8 : 16; - break; - } + info->oob_size = info->spare_size; + if (!info->use_ecc) + info->oob_size += info->ecc_size; } /** @@ -313,10 +416,15 @@ static void pxa3xx_nand_start(struct pxa3xx_nand_info *info) ndcr = info->reg_ndcr; - if (info->use_ecc) + if (info->use_ecc) { ndcr |= NDCR_ECC_EN; - else + if (info->ecc_bch) + nand_writel(info, NDECCCTRL, 0x1); + } else { ndcr &= ~NDCR_ECC_EN; + if (info->ecc_bch) + nand_writel(info, NDECCCTRL, 0x0); + } if (info->use_dma) ndcr |= NDCR_DMA_EN; @@ -375,26 +483,39 @@ static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) static void handle_data_pio(struct pxa3xx_nand_info *info) { + unsigned int do_bytes = min(info->data_size, info->chunk_size); + switch (info->state) { case STATE_PIO_WRITING: - __raw_writesl(info->mmio_base + NDDB, info->data_buff, - DIV_ROUND_UP(info->data_size, 4)); + __raw_writesl(info->mmio_base + NDDB, + info->data_buff + info->data_buff_pos, + DIV_ROUND_UP(do_bytes, 4)); + if (info->oob_size > 0) - __raw_writesl(info->mmio_base + NDDB, info->oob_buff, - DIV_ROUND_UP(info->oob_size, 4)); + __raw_writesl(info->mmio_base + NDDB, + info->oob_buff + info->oob_buff_pos, + DIV_ROUND_UP(info->oob_size, 4)); break; case STATE_PIO_READING: - __raw_readsl(info->mmio_base + NDDB, info->data_buff, - DIV_ROUND_UP(info->data_size, 4)); + __raw_readsl(info->mmio_base + NDDB, + info->data_buff + info->data_buff_pos, + DIV_ROUND_UP(do_bytes, 4)); + if (info->oob_size > 0) - __raw_readsl(info->mmio_base + NDDB, info->oob_buff, - DIV_ROUND_UP(info->oob_size, 4)); + __raw_readsl(info->mmio_base + NDDB, + info->oob_buff + info->oob_buff_pos, + DIV_ROUND_UP(info->oob_size, 4)); break; default: dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, info->state); BUG(); } + + /* Update buffer pointers for multi-page read/write */ + info->data_buff_pos += do_bytes; + info->oob_buff_pos += info->oob_size; + info->data_size -= do_bytes; } #ifdef ARCH_HAS_DMA @@ -452,7 +573,7 @@ static void start_data_dma(struct pxa3xx_nand_info *info) static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) { struct pxa3xx_nand_info *info = devid; - unsigned int status, is_completed = 0; + unsigned int status, is_completed = 0, is_ready = 0; unsigned int ready, cmd_done; if (info->cs == 0) { @@ -465,10 +586,25 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) status = nand_readl(info, NDSR); - if (status & NDSR_DBERR) - info->retcode = ERR_DBERR; - if (status & NDSR_SBERR) - info->retcode = ERR_SBERR; + if (status & NDSR_UNCORERR) + info->retcode = ERR_UNCORERR; + if (status & NDSR_CORERR) { + info->retcode = ERR_CORERR; + if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 && + info->ecc_bch) + info->ecc_err_cnt = NDSR_ERR_CNT(status); + else + info->ecc_err_cnt = 1; + + /* + * Each chunk composing a page is corrected independently, + * and we need to store maximum number of corrected bitflips + * to return it to the MTD layer in ecc.read_page(). + */ + info->max_bitflips = max_t(unsigned int, + info->max_bitflips, + info->ecc_err_cnt); + } if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) { /* whether use dma to transfer data */ if (info->use_dma) { @@ -488,8 +624,8 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) is_completed = 1; } if (status & ready) { - info->is_ready = 1; info->state = STATE_READY; + is_ready = 1; } if (status & NDSR_WRCMDREQ) { @@ -518,6 +654,8 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) nand_writel(info, NDSR, status); if (is_completed) complete(&info->cmd_complete); + if (is_ready) + complete(&info->dev_ready); NORMAL_IRQ_EXIT: return IRQ_HANDLED; } @@ -530,51 +668,94 @@ static inline int is_buf_blank(uint8_t *buf, size_t len) return 1; } -static int prepare_command_pool(struct pxa3xx_nand_info *info, int command, - uint16_t column, int page_addr) +static void set_command_address(struct pxa3xx_nand_info *info, + unsigned int page_size, uint16_t column, int page_addr) { - int addr_cycle, exec_cmd; - struct pxa3xx_nand_host *host; - struct mtd_info *mtd; + /* small page addr setting */ + if (page_size < PAGE_CHUNK_SIZE) { + info->ndcb1 = ((page_addr & 0xFFFFFF) << 8) + | (column & 0xFF); - host = info->host[info->cs]; - mtd = host->mtd; - addr_cycle = 0; - exec_cmd = 1; + info->ndcb2 = 0; + } else { + info->ndcb1 = ((page_addr & 0xFFFF) << 16) + | (column & 0xFFFF); + + if (page_addr & 0xFF0000) + info->ndcb2 = (page_addr & 0xFF0000) >> 16; + else + info->ndcb2 = 0; + } +} + +static void prepare_start_command(struct pxa3xx_nand_info *info, int command) +{ + struct pxa3xx_nand_host *host = info->host[info->cs]; + struct mtd_info *mtd = host->mtd; /* reset data and oob column point to handle data */ info->buf_start = 0; info->buf_count = 0; info->oob_size = 0; + info->data_buff_pos = 0; + info->oob_buff_pos = 0; info->use_ecc = 0; info->use_spare = 1; - info->is_ready = 0; info->retcode = ERR_NONE; - if (info->cs != 0) - info->ndcb0 = NDCB0_CSEL; - else - info->ndcb0 = 0; + info->ecc_err_cnt = 0; + info->ndcb3 = 0; + info->need_wait = 0; switch (command) { case NAND_CMD_READ0: case NAND_CMD_PAGEPROG: info->use_ecc = 1; case NAND_CMD_READOOB: - pxa3xx_set_datasize(info); + pxa3xx_set_datasize(info, mtd); break; case NAND_CMD_PARAM: info->use_spare = 0; break; - case NAND_CMD_SEQIN: - exec_cmd = 0; - break; default: info->ndcb1 = 0; info->ndcb2 = 0; - info->ndcb3 = 0; break; } + /* + * If we are about to issue a read command, or about to set + * the write address, then clean the data buffer. + */ + if (command == NAND_CMD_READ0 || + command == NAND_CMD_READOOB || + command == NAND_CMD_SEQIN) { + + info->buf_count = mtd->writesize + mtd->oobsize; + memset(info->data_buff, 0xFF, info->buf_count); + } + +} + +static int prepare_set_command(struct pxa3xx_nand_info *info, int command, + int ext_cmd_type, uint16_t column, int page_addr) +{ + int addr_cycle, exec_cmd; + struct pxa3xx_nand_host *host; + struct mtd_info *mtd; + + host = info->host[info->cs]; + mtd = host->mtd; + addr_cycle = 0; + exec_cmd = 1; + + if (info->cs != 0) + info->ndcb0 = NDCB0_CSEL; + else + info->ndcb0 = 0; + + if (command == NAND_CMD_SEQIN) + exec_cmd = 0; + addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles + host->col_addr_cycles); @@ -589,30 +770,42 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command, if (command == NAND_CMD_READOOB) info->buf_start += mtd->writesize; - /* Second command setting for large pages */ - if (host->page_size >= PAGE_CHUNK_SIZE) + /* + * Multiple page read needs an 'extended command type' field, + * which is either naked-read or last-read according to the + * state. + */ + if (mtd->writesize == PAGE_CHUNK_SIZE) { info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8); + } else if (mtd->writesize > PAGE_CHUNK_SIZE) { + info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8) + | NDCB0_LEN_OVRD + | NDCB0_EXT_CMD_TYPE(ext_cmd_type); + info->ndcb3 = info->chunk_size + + info->oob_size; + } + + set_command_address(info, mtd->writesize, column, page_addr); + break; case NAND_CMD_SEQIN: - /* small page addr setting */ - if (unlikely(host->page_size < PAGE_CHUNK_SIZE)) { - info->ndcb1 = ((page_addr & 0xFFFFFF) << 8) - | (column & 0xFF); - info->ndcb2 = 0; - } else { - info->ndcb1 = ((page_addr & 0xFFFF) << 16) - | (column & 0xFFFF); + info->buf_start = column; + set_command_address(info, mtd->writesize, 0, page_addr); - if (page_addr & 0xFF0000) - info->ndcb2 = (page_addr & 0xFF0000) >> 16; - else - info->ndcb2 = 0; + /* + * Multiple page programming needs to execute the initial + * SEQIN command that sets the page address. + */ + if (mtd->writesize > PAGE_CHUNK_SIZE) { + info->ndcb0 |= NDCB0_CMD_TYPE(0x1) + | NDCB0_EXT_CMD_TYPE(ext_cmd_type) + | addr_cycle + | command; + /* No data transfer in this case */ + info->data_size = 0; + exec_cmd = 1; } - - info->buf_count = mtd->writesize + mtd->oobsize; - memset(info->data_buff, 0xFF, info->buf_count); - break; case NAND_CMD_PAGEPROG: @@ -622,13 +815,40 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command, break; } - info->ndcb0 |= NDCB0_CMD_TYPE(0x1) - | NDCB0_AUTO_RS - | NDCB0_ST_ROW_EN - | NDCB0_DBC - | (NAND_CMD_PAGEPROG << 8) - | NAND_CMD_SEQIN - | addr_cycle; + /* Second command setting for large pages */ + if (mtd->writesize > PAGE_CHUNK_SIZE) { + /* + * Multiple page write uses the 'extended command' + * field. This can be used to issue a command dispatch + * or a naked-write depending on the current stage. + */ + info->ndcb0 |= NDCB0_CMD_TYPE(0x1) + | NDCB0_LEN_OVRD + | NDCB0_EXT_CMD_TYPE(ext_cmd_type); + info->ndcb3 = info->chunk_size + + info->oob_size; + + /* + * This is the command dispatch that completes a chunked + * page program operation. + */ + if (info->data_size == 0) { + info->ndcb0 = NDCB0_CMD_TYPE(0x1) + | NDCB0_EXT_CMD_TYPE(ext_cmd_type) + | command; + info->ndcb1 = 0; + info->ndcb2 = 0; + info->ndcb3 = 0; + } + } else { + info->ndcb0 |= NDCB0_CMD_TYPE(0x1) + | NDCB0_AUTO_RS + | NDCB0_ST_ROW_EN + | NDCB0_DBC + | (NAND_CMD_PAGEPROG << 8) + | NAND_CMD_SEQIN + | addr_cycle; + } break; case NAND_CMD_PARAM: @@ -691,8 +911,8 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command, return exec_cmd; } -static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command, - int column, int page_addr) +static void nand_cmdfunc(struct mtd_info *mtd, unsigned command, + int column, int page_addr) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; @@ -717,10 +937,15 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command, nand_writel(info, NDTR1CS0, info->ndtr1cs0); } + prepare_start_command(info, command); + info->state = STATE_PREPARED; - exec_cmd = prepare_command_pool(info, command, column, page_addr); + exec_cmd = prepare_set_command(info, command, 0, column, page_addr); + if (exec_cmd) { init_completion(&info->cmd_complete); + init_completion(&info->dev_ready); + info->need_wait = 1; pxa3xx_nand_start(info); ret = wait_for_completion_timeout(&info->cmd_complete, @@ -734,6 +959,117 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command, info->state = STATE_IDLE; } +static void nand_cmdfunc_extended(struct mtd_info *mtd, + const unsigned command, + int column, int page_addr) +{ + struct pxa3xx_nand_host *host = mtd->priv; + struct pxa3xx_nand_info *info = host->info_data; + int ret, exec_cmd, ext_cmd_type; + + /* + * if this is a x16 device then convert the input + * "byte" address into a "word" address appropriate + * for indexing a word-oriented device + */ + if (info->reg_ndcr & NDCR_DWIDTH_M) + column /= 2; + + /* + * There may be different NAND chip hooked to + * different chip select, so check whether + * chip select has been changed, if yes, reset the timing + */ + if (info->cs != host->cs) { + info->cs = host->cs; + nand_writel(info, NDTR0CS0, info->ndtr0cs0); + nand_writel(info, NDTR1CS0, info->ndtr1cs0); + } + + /* Select the extended command for the first command */ + switch (command) { + case NAND_CMD_READ0: + case NAND_CMD_READOOB: + ext_cmd_type = EXT_CMD_TYPE_MONO; + break; + case NAND_CMD_SEQIN: + ext_cmd_type = EXT_CMD_TYPE_DISPATCH; + break; + case NAND_CMD_PAGEPROG: + ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; + break; + default: + ext_cmd_type = 0; + break; + } + + prepare_start_command(info, command); + + /* + * Prepare the "is ready" completion before starting a command + * transaction sequence. If the command is not executed the + * completion will be completed, see below. + * + * We can do that inside the loop because the command variable + * is invariant and thus so is the exec_cmd. + */ + info->need_wait = 1; + init_completion(&info->dev_ready); + do { + info->state = STATE_PREPARED; + exec_cmd = prepare_set_command(info, command, ext_cmd_type, + column, page_addr); + if (!exec_cmd) { + info->need_wait = 0; + complete(&info->dev_ready); + break; + } + + init_completion(&info->cmd_complete); + pxa3xx_nand_start(info); + + ret = wait_for_completion_timeout(&info->cmd_complete, + CHIP_DELAY_TIMEOUT); + if (!ret) { + dev_err(&info->pdev->dev, "Wait time out!!!\n"); + /* Stop State Machine for next command cycle */ + pxa3xx_nand_stop(info); + break; + } + + /* Check if the sequence is complete */ + if (info->data_size == 0 && command != NAND_CMD_PAGEPROG) + break; + + /* + * After a splitted program command sequence has issued + * the command dispatch, the command sequence is complete. + */ + if (info->data_size == 0 && + command == NAND_CMD_PAGEPROG && + ext_cmd_type == EXT_CMD_TYPE_DISPATCH) + break; + + if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) { + /* Last read: issue a 'last naked read' */ + if (info->data_size == info->chunk_size) + ext_cmd_type = EXT_CMD_TYPE_LAST_RW; + else + ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; + + /* + * If a splitted program command has no more data to transfer, + * the command dispatch must be issued to complete. + */ + } else if (command == NAND_CMD_PAGEPROG && + info->data_size == 0) { + ext_cmd_type = EXT_CMD_TYPE_DISPATCH; + } + } while (1); + + info->state = STATE_IDLE; +} + static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required) { @@ -753,20 +1089,14 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd, chip->read_buf(mtd, buf, mtd->writesize); chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); - if (info->retcode == ERR_SBERR) { - switch (info->use_ecc) { - case 1: - mtd->ecc_stats.corrected++; - break; - case 0: - default: - break; - } - } else if (info->retcode == ERR_DBERR) { + if (info->retcode == ERR_CORERR && info->use_ecc) { + mtd->ecc_stats.corrected += info->ecc_err_cnt; + + } else if (info->retcode == ERR_UNCORERR) { /* * for blank page (all 0xff), HW will calculate its ECC as * 0, which is different from the ECC information within - * OOB, ignore such double bit errors + * OOB, ignore such uncorrectable errors */ if (is_buf_blank(buf, mtd->writesize)) info->retcode = ERR_NONE; @@ -774,7 +1104,7 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd, mtd->ecc_stats.failed++; } - return 0; + return info->max_bitflips; } static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd) @@ -833,21 +1163,27 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; + int ret; + + if (info->need_wait) { + ret = wait_for_completion_timeout(&info->dev_ready, + CHIP_DELAY_TIMEOUT); + info->need_wait = 0; + if (!ret) { + dev_err(&info->pdev->dev, "Ready time out!!!\n"); + return NAND_STATUS_FAIL; + } + } /* pxa3xx_nand_send_command has waited for command complete */ if (this->state == FL_WRITING || this->state == FL_ERASING) { if (info->retcode == ERR_NONE) return 0; - else { - /* - * any error make it return 0x01 which will tell - * the caller the erase and write fail - */ - return 0x01; - } + else + return NAND_STATUS_FAIL; } - return 0; + return NAND_STATUS_READY; } static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info, @@ -869,7 +1205,6 @@ static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info, } /* calculate flash information */ - host->page_size = f->page_size; host->read_id_bytes = (f->page_size == 2048) ? 4 : 2; /* calculate addressing information */ @@ -906,13 +1241,15 @@ static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info) uint32_t ndcr = nand_readl(info, NDCR); if (ndcr & NDCR_PAGE_SZ) { - host->page_size = 2048; + /* Controller's FIFO size */ + info->chunk_size = 2048; host->read_id_bytes = 4; } else { - host->page_size = 512; + info->chunk_size = 512; host->read_id_bytes = 2; } + /* Set an initial chunk size */ info->reg_ndcr = ndcr & ~NDCR_INT_MASK; info->ndtr0cs0 = nand_readl(info, NDTR0CS0); info->ndtr1cs0 = nand_readl(info, NDTR1CS0); @@ -988,18 +1325,89 @@ static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info) { struct mtd_info *mtd; + struct nand_chip *chip; int ret; + mtd = info->host[info->cs]->mtd; + chip = mtd->priv; + /* use the common timing to make a try */ ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]); if (ret) return ret; - pxa3xx_nand_cmdfunc(mtd, NAND_CMD_RESET, 0, 0); - if (info->is_ready) - return 0; + chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0); + ret = chip->waitfunc(mtd, chip); + if (ret & NAND_STATUS_FAIL) + return -ENODEV; + + return 0; +} - return -ENODEV; +static int pxa_ecc_init(struct pxa3xx_nand_info *info, + struct nand_ecc_ctrl *ecc, + int strength, int ecc_stepsize, int page_size) +{ + if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) { + info->chunk_size = 2048; + info->spare_size = 40; + info->ecc_size = 24; + ecc->mode = NAND_ECC_HW; + ecc->size = 512; + ecc->strength = 1; + return 1; + + } else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) { + info->chunk_size = 512; + info->spare_size = 8; + info->ecc_size = 8; + ecc->mode = NAND_ECC_HW; + ecc->size = 512; + ecc->strength = 1; + return 1; + + /* + * Required ECC: 4-bit correction per 512 bytes + * Select: 16-bit correction per 2048 bytes + */ + } else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) { + info->ecc_bch = 1; + info->chunk_size = 2048; + info->spare_size = 32; + info->ecc_size = 32; + ecc->mode = NAND_ECC_HW; + ecc->size = info->chunk_size; + ecc->layout = &ecc_layout_2KB_bch4bit; + ecc->strength = 16; + return 1; + + } else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) { + info->ecc_bch = 1; + info->chunk_size = 2048; + info->spare_size = 32; + info->ecc_size = 32; + ecc->mode = NAND_ECC_HW; + ecc->size = info->chunk_size; + ecc->layout = &ecc_layout_4KB_bch4bit; + ecc->strength = 16; + return 1; + + /* + * Required ECC: 8-bit correction per 512 bytes + * Select: 16-bit correction per 1024 bytes + */ + } else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) { + info->ecc_bch = 1; + info->chunk_size = 1024; + info->spare_size = 0; + info->ecc_size = 32; + ecc->mode = NAND_ECC_HW; + ecc->size = info->chunk_size; + ecc->layout = &ecc_layout_4KB_bch8bit; + ecc->strength = 16; + return 1; + } + return 0; } static int pxa3xx_nand_scan(struct mtd_info *mtd) @@ -1014,6 +1422,7 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd) uint32_t id = -1; uint64_t chipsize; int i, ret, num; + uint16_t ecc_strength, ecc_step; if (pdata->keep_config && !pxa3xx_nand_detect_config(info)) goto KEEP_CONFIG; @@ -1072,15 +1481,60 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd) pxa3xx_flash_ids[1].name = NULL; def = pxa3xx_flash_ids; KEEP_CONFIG: - chip->ecc.mode = NAND_ECC_HW; - chip->ecc.size = host->page_size; - chip->ecc.strength = 1; - if (info->reg_ndcr & NDCR_DWIDTH_M) chip->options |= NAND_BUSWIDTH_16; + /* Device detection must be done with ECC disabled */ + if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) + nand_writel(info, NDECCCTRL, 0x0); + if (nand_scan_ident(mtd, 1, def)) return -ENODEV; + + if (pdata->flash_bbt) { + /* + * We'll use a bad block table stored in-flash and don't + * allow writing the bad block marker to the flash. + */ + chip->bbt_options |= NAND_BBT_USE_FLASH | + NAND_BBT_NO_OOB_BBM; + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + } + + /* + * If the page size is bigger than the FIFO size, let's check + * we are given the right variant and then switch to the extended + * (aka splitted) command handling, + */ + if (mtd->writesize > PAGE_CHUNK_SIZE) { + if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) { + chip->cmdfunc = nand_cmdfunc_extended; + } else { + dev_err(&info->pdev->dev, + "unsupported page size on this variant\n"); + return -ENODEV; + } + } + + ecc_strength = chip->ecc_strength_ds; + ecc_step = chip->ecc_step_ds; + + /* Set default ECC strength requirements on non-ONFI devices */ + if (ecc_strength < 1 && ecc_step < 1) { + ecc_strength = 1; + ecc_step = 512; + } + + ret = pxa_ecc_init(info, &chip->ecc, ecc_strength, + ecc_step, mtd->writesize); + if (!ret) { + dev_err(&info->pdev->dev, + "ECC strength %d at page size %d is not supported\n", + chip->ecc_strength_ds, mtd->writesize); + return -ENODEV; + } + /* calculate addressing information */ if (mtd->writesize >= 2048) host->col_addr_cycles = 2; @@ -1121,6 +1575,7 @@ static int alloc_nand_resource(struct platform_device *pdev) return -ENOMEM; info->pdev = pdev; + info->variant = pxa3xx_nand_get_variant(pdev); for (cs = 0; cs < pdata->num_cs; cs++) { mtd = (struct mtd_info *)((unsigned int)&info[1] + (sizeof(*mtd) + sizeof(*host)) * cs); @@ -1138,11 +1593,12 @@ static int alloc_nand_resource(struct platform_device *pdev) chip->controller = &info->controller; chip->waitfunc = pxa3xx_nand_waitfunc; chip->select_chip = pxa3xx_nand_select_chip; - chip->cmdfunc = pxa3xx_nand_cmdfunc; chip->read_word = pxa3xx_nand_read_word; chip->read_byte = pxa3xx_nand_read_byte; chip->read_buf = pxa3xx_nand_read_buf; chip->write_buf = pxa3xx_nand_write_buf; + chip->options |= NAND_NO_SUBPAGE_WRITE; + chip->cmdfunc = nand_cmdfunc; } spin_lock_init(&chip->controller->lock); @@ -1254,25 +1710,6 @@ static int pxa3xx_nand_remove(struct platform_device *pdev) return 0; } -static struct of_device_id pxa3xx_nand_dt_ids[] = { - { - .compatible = "marvell,pxa3xx-nand", - .data = (void *)PXA3XX_NAND_VARIANT_PXA, - }, - {} -}; -MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids); - -static enum pxa3xx_nand_variant -pxa3xx_nand_get_variant(struct platform_device *pdev) -{ - const struct of_device_id *of_id = - of_match_device(pxa3xx_nand_dt_ids, &pdev->dev); - if (!of_id) - return PXA3XX_NAND_VARIANT_PXA; - return (enum pxa3xx_nand_variant)of_id->data; -} - static int pxa3xx_nand_probe_dt(struct platform_device *pdev) { struct pxa3xx_nand_platform_data *pdata; @@ -1292,6 +1729,7 @@ static int pxa3xx_nand_probe_dt(struct platform_device *pdev) if (of_get_property(np, "marvell,nand-keep-config", NULL)) pdata->keep_config = 1; of_property_read_u32(np, "num-cs", &pdata->num_cs); + pdata->flash_bbt = of_get_nand_on_flash_bbt(np); pdev->dev.platform_data = pdata; @@ -1329,7 +1767,6 @@ static int pxa3xx_nand_probe(struct platform_device *pdev) } info = platform_get_drvdata(pdev); - info->variant = pxa3xx_nand_get_variant(pdev); probe_success = 0; for (cs = 0; cs < pdata->num_cs; cs++) { struct mtd_info *mtd = info->host[cs]->mtd; diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/s3c2410.c index d65cbe9..f0918e7 100644 --- a/drivers/mtd/nand/s3c2410.c +++ b/drivers/mtd/nand/s3c2410.c @@ -46,9 +46,43 @@ #include <linux/mtd/nand_ecc.h> #include <linux/mtd/partitions.h> -#include <plat/regs-nand.h> #include <linux/platform_data/mtd-nand-s3c2410.h> +#define S3C2410_NFREG(x) (x) + +#define S3C2410_NFCONF S3C2410_NFREG(0x00) +#define S3C2410_NFCMD S3C2410_NFREG(0x04) +#define S3C2410_NFADDR S3C2410_NFREG(0x08) +#define S3C2410_NFDATA S3C2410_NFREG(0x0C) +#define S3C2410_NFSTAT S3C2410_NFREG(0x10) +#define S3C2410_NFECC S3C2410_NFREG(0x14) +#define S3C2440_NFCONT S3C2410_NFREG(0x04) +#define S3C2440_NFCMD S3C2410_NFREG(0x08) +#define S3C2440_NFADDR S3C2410_NFREG(0x0C) +#define S3C2440_NFDATA S3C2410_NFREG(0x10) +#define S3C2440_NFSTAT S3C2410_NFREG(0x20) +#define S3C2440_NFMECC0 S3C2410_NFREG(0x2C) +#define S3C2412_NFSTAT S3C2410_NFREG(0x28) +#define S3C2412_NFMECC0 S3C2410_NFREG(0x34) +#define S3C2410_NFCONF_EN (1<<15) +#define S3C2410_NFCONF_INITECC (1<<12) +#define S3C2410_NFCONF_nFCE (1<<11) +#define S3C2410_NFCONF_TACLS(x) ((x)<<8) +#define S3C2410_NFCONF_TWRPH0(x) ((x)<<4) +#define S3C2410_NFCONF_TWRPH1(x) ((x)<<0) +#define S3C2410_NFSTAT_BUSY (1<<0) +#define S3C2440_NFCONF_TACLS(x) ((x)<<12) +#define S3C2440_NFCONF_TWRPH0(x) ((x)<<8) +#define S3C2440_NFCONF_TWRPH1(x) ((x)<<4) +#define S3C2440_NFCONT_INITECC (1<<4) +#define S3C2440_NFCONT_nFCE (1<<1) +#define S3C2440_NFCONT_ENABLE (1<<0) +#define S3C2440_NFSTAT_READY (1<<0) +#define S3C2412_NFCONF_NANDBOOT (1<<31) +#define S3C2412_NFCONT_INIT_MAIN_ECC (1<<5) +#define S3C2412_NFCONT_nFCE0 (1<<1) +#define S3C2412_NFSTAT_READY (1<<0) + /* new oob placement block for use with hardware ecc generation */ @@ -919,7 +953,6 @@ static int s3c24xx_nand_probe(struct platform_device *pdev) info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); if (info == NULL) { - dev_err(&pdev->dev, "no memory for flash info\n"); err = -ENOMEM; goto exit_error; } @@ -974,7 +1007,6 @@ static int s3c24xx_nand_probe(struct platform_device *pdev) size = nr_sets * sizeof(*info->mtds); info->mtds = devm_kzalloc(&pdev->dev, size, GFP_KERNEL); if (info->mtds == NULL) { - dev_err(&pdev->dev, "failed to allocate mtd storage\n"); err = -ENOMEM; goto exit_error; } diff --git a/drivers/mtd/nand/sh_flctl.c b/drivers/mtd/nand/sh_flctl.c index a3c84eb..d72783d 100644 --- a/drivers/mtd/nand/sh_flctl.c +++ b/drivers/mtd/nand/sh_flctl.c @@ -151,7 +151,7 @@ static void flctl_setup_dma(struct sh_flctl *flctl) dma_cap_set(DMA_SLAVE, mask); flctl->chan_fifo0_tx = dma_request_channel(mask, shdma_chan_filter, - (void *)pdata->slave_id_fifo0_tx); + (void *)(uintptr_t)pdata->slave_id_fifo0_tx); dev_dbg(&pdev->dev, "%s: TX: got channel %p\n", __func__, flctl->chan_fifo0_tx); @@ -168,7 +168,7 @@ static void flctl_setup_dma(struct sh_flctl *flctl) goto err; flctl->chan_fifo0_rx = dma_request_channel(mask, shdma_chan_filter, - (void *)pdata->slave_id_fifo0_rx); + (void *)(uintptr_t)pdata->slave_id_fifo0_rx); dev_dbg(&pdev->dev, "%s: RX: got channel %p\n", __func__, flctl->chan_fifo0_rx); @@ -1021,7 +1021,6 @@ static irqreturn_t flctl_handle_flste(int irq, void *dev_id) return IRQ_HANDLED; } -#ifdef CONFIG_OF struct flctl_soc_config { unsigned long flcmncr_val; unsigned has_hwecc:1; @@ -1059,10 +1058,8 @@ static struct sh_flctl_platform_data *flctl_parse_dt(struct device *dev) pdata = devm_kzalloc(dev, sizeof(struct sh_flctl_platform_data), GFP_KERNEL); - if (!pdata) { - dev_err(dev, "%s: failed to allocate config data\n", __func__); + if (!pdata) return NULL; - } /* set SoC specific options */ pdata->flcmncr_val = config->flcmncr_val; @@ -1080,12 +1077,6 @@ static struct sh_flctl_platform_data *flctl_parse_dt(struct device *dev) return pdata; } -#else /* CONFIG_OF */ -static struct sh_flctl_platform_data *flctl_parse_dt(struct device *dev) -{ - return NULL; -} -#endif /* CONFIG_OF */ static int flctl_probe(struct platform_device *pdev) { @@ -1094,38 +1085,30 @@ static int flctl_probe(struct platform_device *pdev) struct mtd_info *flctl_mtd; struct nand_chip *nand; struct sh_flctl_platform_data *pdata; - int ret = -ENXIO; + int ret; int irq; struct mtd_part_parser_data ppdata = {}; - flctl = kzalloc(sizeof(struct sh_flctl), GFP_KERNEL); - if (!flctl) { - dev_err(&pdev->dev, "failed to allocate driver data\n"); + flctl = devm_kzalloc(&pdev->dev, sizeof(struct sh_flctl), GFP_KERNEL); + if (!flctl) return -ENOMEM; - } res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) { - dev_err(&pdev->dev, "failed to get I/O memory\n"); - goto err_iomap; - } - - flctl->reg = ioremap(res->start, resource_size(res)); - if (flctl->reg == NULL) { - dev_err(&pdev->dev, "failed to remap I/O memory\n"); - goto err_iomap; - } + flctl->reg = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(flctl->reg)) + return PTR_ERR(flctl->reg); irq = platform_get_irq(pdev, 0); if (irq < 0) { dev_err(&pdev->dev, "failed to get flste irq data\n"); - goto err_flste; + return -ENXIO; } - ret = request_irq(irq, flctl_handle_flste, IRQF_SHARED, "flste", flctl); + ret = devm_request_irq(&pdev->dev, irq, flctl_handle_flste, IRQF_SHARED, + "flste", flctl); if (ret) { dev_err(&pdev->dev, "request interrupt failed.\n"); - goto err_flste; + return ret; } if (pdev->dev.of_node) @@ -1135,8 +1118,7 @@ static int flctl_probe(struct platform_device *pdev) if (!pdata) { dev_err(&pdev->dev, "no setup data defined\n"); - ret = -EINVAL; - goto err_pdata; + return -EINVAL; } platform_set_drvdata(pdev, flctl); @@ -1190,12 +1172,6 @@ static int flctl_probe(struct platform_device *pdev) err_chip: flctl_release_dma(flctl); pm_runtime_disable(&pdev->dev); -err_pdata: - free_irq(irq, flctl); -err_flste: - iounmap(flctl->reg); -err_iomap: - kfree(flctl); return ret; } @@ -1206,9 +1182,6 @@ static int flctl_remove(struct platform_device *pdev) flctl_release_dma(flctl); nand_release(&flctl->mtd); pm_runtime_disable(&pdev->dev); - free_irq(platform_get_irq(pdev, 0), flctl); - iounmap(flctl->reg); - kfree(flctl); return 0; } diff --git a/drivers/mtd/nand/sharpsl.c b/drivers/mtd/nand/sharpsl.c index 87908d7..e81059b 100644 --- a/drivers/mtd/nand/sharpsl.c +++ b/drivers/mtd/nand/sharpsl.c @@ -121,10 +121,8 @@ static int sharpsl_nand_probe(struct platform_device *pdev) /* Allocate memory for MTD device structure and private data */ sharpsl = kzalloc(sizeof(struct sharpsl_nand), GFP_KERNEL); - if (!sharpsl) { - printk("Unable to allocate SharpSL NAND MTD device structure.\n"); + if (!sharpsl) return -ENOMEM; - } r = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!r) { @@ -136,7 +134,7 @@ static int sharpsl_nand_probe(struct platform_device *pdev) /* map physical address */ sharpsl->io = ioremap(r->start, resource_size(r)); if (!sharpsl->io) { - printk("ioremap to access Sharp SL NAND chip failed\n"); + dev_err(&pdev->dev, "ioremap to access Sharp SL NAND chip failed\n"); err = -EIO; goto err_ioremap; } diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/tmio_nand.c index a3747c9..fb8fd35 100644 --- a/drivers/mtd/nand/tmio_nand.c +++ b/drivers/mtd/nand/tmio_nand.c @@ -371,11 +371,9 @@ static int tmio_probe(struct platform_device *dev) if (data == NULL) dev_warn(&dev->dev, "NULL platform data!\n"); - tmio = kzalloc(sizeof *tmio, GFP_KERNEL); - if (!tmio) { - retval = -ENOMEM; - goto err_kzalloc; - } + tmio = devm_kzalloc(&dev->dev, sizeof(*tmio), GFP_KERNEL); + if (!tmio) + return -ENOMEM; tmio->dev = dev; @@ -385,22 +383,18 @@ static int tmio_probe(struct platform_device *dev) mtd->priv = nand_chip; mtd->name = "tmio-nand"; - tmio->ccr = ioremap(ccr->start, resource_size(ccr)); - if (!tmio->ccr) { - retval = -EIO; - goto err_iomap_ccr; - } + tmio->ccr = devm_ioremap(&dev->dev, ccr->start, resource_size(ccr)); + if (!tmio->ccr) + return -EIO; tmio->fcr_base = fcr->start & 0xfffff; - tmio->fcr = ioremap(fcr->start, resource_size(fcr)); - if (!tmio->fcr) { - retval = -EIO; - goto err_iomap_fcr; - } + tmio->fcr = devm_ioremap(&dev->dev, fcr->start, resource_size(fcr)); + if (!tmio->fcr) + return -EIO; retval = tmio_hw_init(dev, tmio); if (retval) - goto err_hwinit; + return retval; /* Set address of NAND IO lines */ nand_chip->IO_ADDR_R = tmio->fcr; @@ -428,7 +422,8 @@ static int tmio_probe(struct platform_device *dev) /* 15 us command delay time */ nand_chip->chip_delay = 15; - retval = request_irq(irq, &tmio_irq, 0, dev_name(&dev->dev), tmio); + retval = devm_request_irq(&dev->dev, irq, &tmio_irq, 0, + dev_name(&dev->dev), tmio); if (retval) { dev_err(&dev->dev, "request_irq error %d\n", retval); goto err_irq; @@ -440,7 +435,7 @@ static int tmio_probe(struct platform_device *dev) /* Scan to find existence of the device */ if (nand_scan(mtd, 1)) { retval = -ENODEV; - goto err_scan; + goto err_irq; } /* Register the partitions */ retval = mtd_device_parse_register(mtd, NULL, NULL, @@ -451,18 +446,8 @@ static int tmio_probe(struct platform_device *dev) nand_release(mtd); -err_scan: - if (tmio->irq) - free_irq(tmio->irq, tmio); err_irq: tmio_hw_stop(dev, tmio); -err_hwinit: - iounmap(tmio->fcr); -err_iomap_fcr: - iounmap(tmio->ccr); -err_iomap_ccr: - kfree(tmio); -err_kzalloc: return retval; } @@ -471,12 +456,7 @@ static int tmio_remove(struct platform_device *dev) struct tmio_nand *tmio = platform_get_drvdata(dev); nand_release(&tmio->mtd); - if (tmio->irq) - free_irq(tmio->irq, tmio); tmio_hw_stop(dev, tmio); - iounmap(tmio->fcr); - iounmap(tmio->ccr); - kfree(tmio); return 0; } diff --git a/drivers/mtd/nand/txx9ndfmc.c b/drivers/mtd/nand/txx9ndfmc.c index 235714a..c1622a5 100644 --- a/drivers/mtd/nand/txx9ndfmc.c +++ b/drivers/mtd/nand/txx9ndfmc.c @@ -319,11 +319,8 @@ static int __init txx9ndfmc_probe(struct platform_device *dev) continue; txx9_priv = kzalloc(sizeof(struct txx9ndfmc_priv), GFP_KERNEL); - if (!txx9_priv) { - dev_err(&dev->dev, "Unable to allocate " - "TXx9 NDFMC MTD device structure.\n"); + if (!txx9_priv) continue; - } chip = &txx9_priv->chip; mtd = &txx9_priv->mtd; mtd->owner = THIS_MODULE; diff --git a/drivers/mtd/ofpart.c b/drivers/mtd/ofpart.c index d64f8c3..aa26c32 100644 --- a/drivers/mtd/ofpart.c +++ b/drivers/mtd/ofpart.c @@ -81,7 +81,7 @@ static int parse_ofpart_partitions(struct mtd_info *master, partname = of_get_property(pp, "label", &len); if (!partname) partname = of_get_property(pp, "name", &len); - (*pparts)[i].name = (char *)partname; + (*pparts)[i].name = partname; if (of_get_property(pp, "read-only", &len)) (*pparts)[i].mask_flags |= MTD_WRITEABLE; @@ -152,7 +152,7 @@ static int parse_ofoldpart_partitions(struct mtd_info *master, if (names && (plen > 0)) { int len = strlen(names) + 1; - (*pparts)[i].name = (char *)names; + (*pparts)[i].name = names; plen -= len; names += len; } else { @@ -173,18 +173,9 @@ static struct mtd_part_parser ofoldpart_parser = { static int __init ofpart_parser_init(void) { - int rc; - rc = register_mtd_parser(&ofpart_parser); - if (rc) - goto out; - - rc = register_mtd_parser(&ofoldpart_parser); - if (!rc) - return 0; - - deregister_mtd_parser(&ofoldpart_parser); -out: - return rc; + register_mtd_parser(&ofpart_parser); + register_mtd_parser(&ofoldpart_parser); + return 0; } static void __exit ofpart_parser_exit(void) diff --git a/drivers/mtd/onenand/generic.c b/drivers/mtd/onenand/generic.c index 63699ff..8e1919b 100644 --- a/drivers/mtd/onenand/generic.c +++ b/drivers/mtd/onenand/generic.c @@ -58,7 +58,7 @@ static int generic_onenand_probe(struct platform_device *pdev) goto out_release_mem_region; } - info->onenand.mmcontrol = pdata ? pdata->mmcontrol : 0; + info->onenand.mmcontrol = pdata ? pdata->mmcontrol : NULL; info->onenand.irq = platform_get_irq(pdev, 0); info->mtd.name = dev_name(&pdev->dev); diff --git a/drivers/mtd/redboot.c b/drivers/mtd/redboot.c index 580035c..5da911e 100644 --- a/drivers/mtd/redboot.c +++ b/drivers/mtd/redboot.c @@ -300,7 +300,8 @@ MODULE_ALIAS("RedBoot"); static int __init redboot_parser_init(void) { - return register_mtd_parser(&redboot_parser); + register_mtd_parser(&redboot_parser); + return 0; } static void __exit redboot_parser_exit(void) diff --git a/drivers/mtd/tests/mtd_nandecctest.c b/drivers/mtd/tests/mtd_nandecctest.c index 7010660..e579f90 100644 --- a/drivers/mtd/tests/mtd_nandecctest.c +++ b/drivers/mtd/tests/mtd_nandecctest.c @@ -19,7 +19,7 @@ * or detected. */ -#if defined(CONFIG_MTD_NAND) || defined(CONFIG_MTD_NAND_MODULE) +#if IS_ENABLED(CONFIG_MTD_NAND) struct nand_ecc_test { const char *name; diff --git a/fs/jffs2/malloc.c b/fs/jffs2/malloc.c index 4f47aa2..b8fd651 100644 --- a/fs/jffs2/malloc.c +++ b/fs/jffs2/malloc.c @@ -288,6 +288,8 @@ struct jffs2_xattr_datum *jffs2_alloc_xattr_datum(void) struct jffs2_xattr_datum *xd; xd = kmem_cache_zalloc(xattr_datum_cache, GFP_KERNEL); dbg_memalloc("%p\n", xd); + if (!xd) + return NULL; xd->class = RAWNODE_CLASS_XATTR_DATUM; xd->node = (void *)xd; @@ -306,6 +308,8 @@ struct jffs2_xattr_ref *jffs2_alloc_xattr_ref(void) struct jffs2_xattr_ref *ref; ref = kmem_cache_zalloc(xattr_ref_cache, GFP_KERNEL); dbg_memalloc("%p\n", ref); + if (!ref) + return NULL; ref->class = RAWNODE_CLASS_XATTR_REF; ref->node = (void *)ref; diff --git a/include/linux/mtd/mtdram.h b/include/linux/mtd/mtdram.h index 6889131..628a6a2 100644 --- a/include/linux/mtd/mtdram.h +++ b/include/linux/mtd/mtdram.h @@ -3,6 +3,6 @@ #include <linux/mtd/mtd.h> int mtdram_init_device(struct mtd_info *mtd, void *mapped_address, - unsigned long size, char *name); + unsigned long size, const char *name); #endif /* __MTD_MTDRAM_H__ */ diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index 9e6c8f9..32f8612 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -219,6 +219,9 @@ struct nand_chip; /* ONFI feature address */ #define ONFI_FEATURE_ADDR_TIMING_MODE 0x1 +/* Vendor-specific feature address (Micron) */ +#define ONFI_FEATURE_ADDR_READ_RETRY 0x89 + /* ONFI subfeature parameters length */ #define ONFI_SUBFEATURE_PARAM_LEN 4 @@ -279,16 +282,17 @@ struct nand_onfi_params { __le16 io_pin_capacitance_typ; __le16 input_pin_capacitance_typ; u8 input_pin_capacitance_max; - u8 driver_strenght_support; + u8 driver_strength_support; __le16 t_int_r; __le16 t_ald; u8 reserved4[7]; /* vendor */ - u8 reserved5[90]; + __le16 vendor_revision; + u8 vendor[88]; __le16 crc; -} __attribute__((packed)); +} __packed; #define ONFI_CRC_BASE 0x4F4E @@ -326,6 +330,26 @@ struct onfi_ext_param_page { */ } __packed; +struct nand_onfi_vendor_micron { + u8 two_plane_read; + u8 read_cache; + u8 read_unique_id; + u8 dq_imped; + u8 dq_imped_num_settings; + u8 dq_imped_feat_addr; + u8 rb_pulldown_strength; + u8 rb_pulldown_strength_feat_addr; + u8 rb_pulldown_strength_num_settings; + u8 otp_mode; + u8 otp_page_start; + u8 otp_data_prot_addr; + u8 otp_num_pages; + u8 otp_feat_addr; + u8 read_retry_options; + u8 reserved[72]; + u8 param_revision; +} __packed; + /** * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices * @lock: protection lock @@ -432,6 +456,8 @@ struct nand_buffers { * flash device. * @read_byte: [REPLACEABLE] read one byte from the chip * @read_word: [REPLACEABLE] read one word from the chip + * @write_byte: [REPLACEABLE] write a single byte to the chip on the + * low 8 I/O lines * @write_buf: [REPLACEABLE] write data from the buffer to the chip * @read_buf: [REPLACEABLE] read data from the chip into the buffer * @select_chip: [REPLACEABLE] select chip nr @@ -451,6 +477,8 @@ struct nand_buffers { * commands to the chip. * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on * ready. + * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for + * setting the read-retry mode. Mostly needed for MLC NAND. * @ecc: [BOARDSPECIFIC] ECC control structure * @buffers: buffer structure for read/write * @hwcontrol: platform-specific hardware control structure @@ -497,6 +525,7 @@ struct nand_buffers { * non 0 if ONFI supported. * @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is * supported, 0 otherwise. + * @read_retries: [INTERN] the number of read retry modes supported * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand * @bbt: [INTERN] bad block table pointer @@ -521,6 +550,7 @@ struct nand_chip { uint8_t (*read_byte)(struct mtd_info *mtd); u16 (*read_word)(struct mtd_info *mtd); + void (*write_byte)(struct mtd_info *mtd, uint8_t byte); void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); void (*select_chip)(struct mtd_info *mtd, int chip); @@ -544,6 +574,7 @@ struct nand_chip { int feature_addr, uint8_t *subfeature_para); int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip, int feature_addr, uint8_t *subfeature_para); + int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode); int chip_delay; unsigned int options; @@ -568,6 +599,8 @@ struct nand_chip { int onfi_version; struct nand_onfi_params onfi_params; + int read_retries; + flstate_t state; uint8_t *oob_poi; @@ -600,6 +633,8 @@ struct nand_chip { #define NAND_MFR_AMD 0x01 #define NAND_MFR_MACRONIX 0xc2 #define NAND_MFR_EON 0x92 +#define NAND_MFR_SANDISK 0x45 +#define NAND_MFR_INTEL 0x89 /* The maximum expected count of bytes in the NAND ID sequence */ #define NAND_MAX_ID_LEN 8 diff --git a/include/linux/mtd/partitions.h b/include/linux/mtd/partitions.h index 1f8d24b..6a35e6d 100644 --- a/include/linux/mtd/partitions.h +++ b/include/linux/mtd/partitions.h @@ -37,7 +37,7 @@ */ struct mtd_partition { - char *name; /* identifier string */ + const char *name; /* identifier string */ uint64_t size; /* partition size */ uint64_t offset; /* offset within the master MTD space */ uint32_t mask_flags; /* master MTD flags to mask out for this partition */ @@ -76,11 +76,11 @@ struct mtd_part_parser { struct mtd_part_parser_data *); }; -extern int register_mtd_parser(struct mtd_part_parser *parser); -extern int deregister_mtd_parser(struct mtd_part_parser *parser); +extern void register_mtd_parser(struct mtd_part_parser *parser); +extern void deregister_mtd_parser(struct mtd_part_parser *parser); int mtd_is_partition(const struct mtd_info *mtd); -int mtd_add_partition(struct mtd_info *master, char *name, +int mtd_add_partition(struct mtd_info *master, const char *name, long long offset, long long length); int mtd_del_partition(struct mtd_info *master, int partno); uint64_t mtd_get_device_size(const struct mtd_info *mtd); diff --git a/include/linux/of_mtd.h b/include/linux/of_mtd.h index 6f10e93..cb32d9c 100644 --- a/include/linux/of_mtd.h +++ b/include/linux/of_mtd.h @@ -7,7 +7,7 @@ */ #ifndef __LINUX_OF_MTD_H -#define __LINUX_OF_NET_H +#define __LINUX_OF_MTD_H #ifdef CONFIG_OF_MTD diff --git a/include/linux/platform_data/mtd-nand-omap2.h b/include/linux/platform_data/mtd-nand-omap2.h index 4da5bfa..3e9dd66 100644 --- a/include/linux/platform_data/mtd-nand-omap2.h +++ b/include/linux/platform_data/mtd-nand-omap2.h @@ -1,6 +1,4 @@ /* - * arch/arm/plat-omap/include/mach/nand.h - * * Copyright (C) 2006 Micron Technology Inc. * * This program is free software; you can redistribute it and/or modify diff --git a/include/linux/platform_data/mtd-nand-pxa3xx.h b/include/linux/platform_data/mtd-nand-pxa3xx.h index ffb8019..a941471 100644 --- a/include/linux/platform_data/mtd-nand-pxa3xx.h +++ b/include/linux/platform_data/mtd-nand-pxa3xx.h @@ -55,6 +55,9 @@ struct pxa3xx_nand_platform_data { /* indicate how many chip selects will be used */ int num_cs; + /* use an flash-based bad block table */ + bool flash_bbt; + const struct mtd_partition *parts[NUM_CHIP_SELECT]; unsigned int nr_parts[NUM_CHIP_SELECT]; diff --git a/include/linux/platform_data/mtd-onenand-omap2.h b/include/linux/platform_data/mtd-onenand-omap2.h index e9a9fb1..56ff0e6 100644 --- a/include/linux/platform_data/mtd-onenand-omap2.h +++ b/include/linux/platform_data/mtd-onenand-omap2.h @@ -1,6 +1,4 @@ /* - * arch/arm/plat-omap/include/mach/onenand.h - * * Copyright (C) 2006 Nokia Corporation * Author: Juha Yrjola * diff --git a/include/linux/platform_data/mtd-orion_nand.h b/include/linux/platform_data/mtd-orion_nand.h index 9f3c180..a7ce77c 100644 --- a/include/linux/platform_data/mtd-orion_nand.h +++ b/include/linux/platform_data/mtd-orion_nand.h @@ -1,13 +1,11 @@ /* - * arch/arm/plat-orion/include/plat/orion_nand.h - * * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. */ -#ifndef __PLAT_ORION_NAND_H -#define __PLAT_ORION_NAND_H +#ifndef __MTD_ORION_NAND_H +#define __MTD_ORION_NAND_H /* * Device bus NAND private data |
