diff options
| -rw-r--r-- | arch/arm/plat-omap/include/plat/omap-serial.h | 4 | ||||
| -rw-r--r-- | drivers/tty/serial/omap-serial.c | 43 |
2 files changed, 30 insertions, 17 deletions
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h index db9bda9..70e7738 100644 --- a/arch/arm/plat-omap/include/plat/omap-serial.h +++ b/arch/arm/plat-omap/include/plat/omap-serial.h @@ -97,6 +97,10 @@ struct uart_omap_port { unsigned char mcr; unsigned char fcr; unsigned char efr; + unsigned char dll; + unsigned char dlh; + unsigned char mdr1; + unsigned char scr; int use_dma; /* diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c index a834e91..5327ff0 100644 --- a/drivers/tty/serial/omap-serial.c +++ b/drivers/tty/serial/omap-serial.c @@ -466,8 +466,9 @@ static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl) mcr |= UART_MCR_LOOP; pm_runtime_get_sync(&up->pdev->dev); - mcr |= up->mcr; - serial_out(up, UART_MCR, mcr); + up->mcr = serial_in(up, UART_MCR); + up->mcr |= mcr; + serial_out(up, UART_MCR, up->mcr); pm_runtime_put(&up->pdev->dev); } @@ -616,8 +617,6 @@ static inline void serial_omap_configure_xonxoff (struct uart_omap_port *up, struct ktermios *termios) { - unsigned char efr = 0; - up->lcr = serial_in(up, UART_LCR); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); up->efr = serial_in(up, UART_EFR); @@ -627,8 +626,7 @@ serial_omap_configure_xonxoff serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]); /* clear SW control mode bits */ - efr = up->efr; - efr &= OMAP_UART_SW_CLR; + up->efr &= OMAP_UART_SW_CLR; /* * IXON Flag: @@ -636,7 +634,7 @@ serial_omap_configure_xonxoff * Transmit XON1, XOFF1 */ if (termios->c_iflag & IXON) - efr |= OMAP_UART_SW_TX; + up->efr |= OMAP_UART_SW_TX; /* * IXOFF Flag: @@ -644,7 +642,7 @@ serial_omap_configure_xonxoff * Receiver compares XON1, XOFF1. */ if (termios->c_iflag & IXOFF) - efr |= OMAP_UART_SW_RX; + up->efr |= OMAP_UART_SW_RX; serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); @@ -667,7 +665,7 @@ serial_omap_configure_xonxoff * load the new software flow control mode IXON or IXOFF * and restore the UARTi.EFR_REG[4] ENHANCED_EN value. */ - serial_out(up, UART_EFR, efr | UART_EFR_SCD); + serial_out(up, UART_EFR, up->efr | UART_EFR_SCD); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); serial_out(up, UART_MCR, up->mcr & ~UART_MCR_TCRTLR); @@ -714,6 +712,10 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13); quot = serial_omap_get_divisor(port, baud); + up->dll = quot & 0xff; + up->dlh = quot >> 8; + up->mdr1 = UART_OMAP_MDR1_DISABLE; + up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 | UART_FCR_ENABLE_FIFO; if (up->use_dma) @@ -767,6 +769,7 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, up->ier |= UART_IER_MSI; serial_out(up, UART_IER, up->ier); serial_out(up, UART_LCR, cval); /* reset DLAB */ + up->lcr = cval; /* FIFOs and DMA Settings */ @@ -793,17 +796,18 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, if (up->use_dma) { serial_out(up, UART_TI752_TLR, 0); - serial_out(up, UART_OMAP_SCR, - (UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8)); + up->scr |= (UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8); } + serial_out(up, UART_OMAP_SCR, up->scr); + serial_out(up, UART_EFR, up->efr); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); serial_out(up, UART_MCR, up->mcr); /* Protocol, Baud Rate, and Interrupt Settings */ - serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE); + serial_out(up, UART_OMAP_MDR1, up->mdr1); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); up->efr = serial_in(up, UART_EFR); @@ -813,8 +817,8 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, serial_out(up, UART_IER, 0); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */ - serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */ + serial_out(up, UART_DLL, up->dll); /* LS of divisor */ + serial_out(up, UART_DLM, up->dlh); /* MS of divisor */ serial_out(up, UART_LCR, 0); serial_out(up, UART_IER, up->ier); @@ -824,9 +828,11 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, serial_out(up, UART_LCR, cval); if (baud > 230400 && baud != 3000000) - serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_13X_MODE); + up->mdr1 = UART_OMAP_MDR1_13X_MODE; else - serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE); + up->mdr1 = UART_OMAP_MDR1_16X_MODE; + + serial_out(up, UART_OMAP_MDR1, up->mdr1); /* Hardware Flow Control Configuration */ @@ -1416,15 +1422,18 @@ static void serial_omap_restore_context(struct uart_omap_port *up) serial_out(up, UART_LCR, 0x0); /* Operational mode */ serial_out(up, UART_IER, 0x0); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */ + serial_out(up, UART_DLL, up->dll); + serial_out(up, UART_DLM, up->dlh); serial_out(up, UART_LCR, 0x0); /* Operational mode */ serial_out(up, UART_IER, up->ier); serial_out(up, UART_FCR, up->fcr); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); serial_out(up, UART_MCR, up->mcr); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */ + serial_out(up, UART_OMAP_SCR, up->scr); serial_out(up, UART_EFR, up->efr); serial_out(up, UART_LCR, up->lcr); - serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE); + serial_out(up, UART_OMAP_MDR1, up->mdr1); } #ifdef CONFIG_PM_RUNTIME |
