diff options
| -rw-r--r-- | Documentation/hwmon/lm80 | 9 | ||||
| -rw-r--r-- | drivers/hwmon/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/hwmon/lm80.c | 44 |
3 files changed, 45 insertions, 12 deletions
diff --git a/Documentation/hwmon/lm80 b/Documentation/hwmon/lm80 index cb5b407..a60b43e 100644 --- a/Documentation/hwmon/lm80 +++ b/Documentation/hwmon/lm80 @@ -7,6 +7,11 @@ Supported chips: Addresses scanned: I2C 0x28 - 0x2f Datasheet: Publicly available at the National Semiconductor website http://www.national.com/ + * National Semiconductor LM96080 + Prefix: 'lm96080' + Addresses scanned: I2C 0x28 - 0x2f + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/ Authors: Frodo Looijaard <frodol@dds.nl>, @@ -17,7 +22,9 @@ Description This driver implements support for the National Semiconductor LM80. It is described as a 'Serial Interface ACPI-Compatible Microprocessor -System Hardware Monitor'. +System Hardware Monitor'. The LM96080 is a more recent incarnation, +it is pin and register compatible, with a few additional features not +yet supported by the driver. The LM80 implements one temperature sensor, two fan rotation speed sensors, seven voltage sensors, alarms, and some miscellaneous stuff. diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index dad895f..1cd0e20 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -598,11 +598,11 @@ config SENSORS_LM78 will be called lm78. config SENSORS_LM80 - tristate "National Semiconductor LM80" + tristate "National Semiconductor LM80 and LM96080" depends on I2C help If you say yes here you get support for National Semiconductor - LM80 sensor chips. + LM80 and LM96080 sensor chips. This driver can also be built as a module. If so, the module will be called lm80. diff --git a/drivers/hwmon/lm80.c b/drivers/hwmon/lm80.c index a996f27..e2c43e1 100644 --- a/drivers/hwmon/lm80.c +++ b/drivers/hwmon/lm80.c @@ -60,6 +60,10 @@ static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, #define LM80_REG_FANDIV 0x05 #define LM80_REG_RES 0x06 +#define LM96080_REG_CONV_RATE 0x07 +#define LM96080_REG_MAN_ID 0x3e +#define LM96080_REG_DEV_ID 0x3f + /* * Conversions. Rounding and limit checking is only done on the TO_REG @@ -147,6 +151,7 @@ static int lm80_write_value(struct i2c_client *client, u8 reg, u8 value); static const struct i2c_device_id lm80_id[] = { { "lm80", 0 }, + { "lm96080", 1 }, { } }; MODULE_DEVICE_TABLE(i2c, lm80_id); @@ -490,23 +495,44 @@ static const struct attribute_group lm80_group = { static int lm80_detect(struct i2c_client *client, struct i2c_board_info *info) { struct i2c_adapter *adapter = client->adapter; - int i, cur; + int i, cur, man_id, dev_id; + const char *name = NULL; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) return -ENODEV; - /* Now, we do the remaining detection. It is lousy. */ - if (lm80_read_value(client, LM80_REG_ALARM2) & 0xc0) + /* First check for unused bits, common to both chip types */ + if ((lm80_read_value(client, LM80_REG_ALARM2) & 0xc0) + || (lm80_read_value(client, LM80_REG_CONFIG) & 0x80)) return -ENODEV; - for (i = 0x2a; i <= 0x3d; i++) { - cur = i2c_smbus_read_byte_data(client, i); - if ((i2c_smbus_read_byte_data(client, i + 0x40) != cur) - || (i2c_smbus_read_byte_data(client, i + 0x80) != cur) - || (i2c_smbus_read_byte_data(client, i + 0xc0) != cur)) + + /* + * The LM96080 has manufacturer and stepping/die rev registers so we + * can just check that. The LM80 does not have such registers so we + * have to use a more expensive trick. + */ + man_id = lm80_read_value(client, LM96080_REG_MAN_ID); + dev_id = lm80_read_value(client, LM96080_REG_DEV_ID); + if (man_id == 0x01 && dev_id == 0x08) { + /* Check more unused bits for confirmation */ + if (lm80_read_value(client, LM96080_REG_CONV_RATE) & 0xfe) return -ENODEV; + + name = "lm96080"; + } else { + /* Check 6-bit addressing */ + for (i = 0x2a; i <= 0x3d; i++) { + cur = i2c_smbus_read_byte_data(client, i); + if ((i2c_smbus_read_byte_data(client, i + 0x40) != cur) + || (i2c_smbus_read_byte_data(client, i + 0x80) != cur) + || (i2c_smbus_read_byte_data(client, i + 0xc0) != cur)) + return -ENODEV; + } + + name = "lm80"; } - strlcpy(info->type, "lm80", I2C_NAME_SIZE); + strlcpy(info->type, name, I2C_NAME_SIZE); return 0; } |
