diff options
38 files changed, 311 insertions, 421 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 3438384..ffcaf97 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8917,61 +8917,14 @@ W: http://pegasus2.sourceforge.net/ S: Maintained F: drivers/net/usb/rtl8150.c -USB SERIAL BELKIN F5U103 DRIVER -M: William Greathouse <wgreathouse@smva.com> +USB SERIAL SUBSYSTEM +M: Johan Hovold <jhovold@gmail.com> L: linux-usb@vger.kernel.org S: Maintained -F: drivers/usb/serial/belkin_sa.* - -USB SERIAL CYPRESS M8 DRIVER -M: Lonnie Mendez <dignome@gmail.com> -L: linux-usb@vger.kernel.org -S: Maintained -W: http://geocities.com/i0xox0i -W: http://firstlight.net/cvs -F: drivers/usb/serial/cypress_m8.* - -USB SERIAL CYBERJACK DRIVER -M: Matthias Bruestle and Harald Welte <support@reiner-sct.com> -W: http://www.reiner-sct.de/support/treiber_cyberjack.php -S: Maintained -F: drivers/usb/serial/cyberjack.c - -USB SERIAL DIGI ACCELEPORT DRIVER -M: Peter Berger <pberger@brimson.com> -M: Al Borchers <alborchers@steinerpoint.com> -L: linux-usb@vger.kernel.org -S: Maintained -F: drivers/usb/serial/digi_acceleport.c - -USB SERIAL DRIVER -M: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -L: linux-usb@vger.kernel.org -S: Supported F: Documentation/usb/usb-serial.txt -F: drivers/usb/serial/generic.c -F: drivers/usb/serial/usb-serial.c +F: drivers/usb/serial/ F: include/linux/usb/serial.h -USB SERIAL EMPEG EMPEG-CAR MARK I/II DRIVER -M: Gary Brubaker <xavyer@ix.netcom.com> -L: linux-usb@vger.kernel.org -S: Maintained -F: drivers/usb/serial/empeg.c - -USB SERIAL KEYSPAN DRIVER -M: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -L: linux-usb@vger.kernel.org -S: Maintained -F: drivers/usb/serial/*keyspan* - -USB SERIAL WHITEHEAT DRIVER -M: Support Department <support@connecttech.com> -L: linux-usb@vger.kernel.org -W: http://www.connecttech.com -S: Supported -F: drivers/usb/serial/whiteheat* - USB SMSC75XX ETHERNET DRIVER M: Steve Glendinning <steve.glendinning@shawell.net> L: netdev@vger.kernel.org diff --git a/arch/arc/mm/fault.c b/arch/arc/mm/fault.c index d63f3de..0c14d8a 100644 --- a/arch/arc/mm/fault.c +++ b/arch/arc/mm/fault.c @@ -17,7 +17,7 @@ #include <asm/pgalloc.h> #include <asm/mmu.h> -static int handle_vmalloc_fault(struct mm_struct *mm, unsigned long address) +static int handle_vmalloc_fault(unsigned long address) { /* * Synchronize this task's top level page-table @@ -27,7 +27,7 @@ static int handle_vmalloc_fault(struct mm_struct *mm, unsigned long address) pud_t *pud, *pud_k; pmd_t *pmd, *pmd_k; - pgd = pgd_offset_fast(mm, address); + pgd = pgd_offset_fast(current->active_mm, address); pgd_k = pgd_offset_k(address); if (!pgd_present(*pgd_k)) @@ -72,7 +72,7 @@ void do_page_fault(struct pt_regs *regs, unsigned long address) * nothing more. */ if (address >= VMALLOC_START && address <= VMALLOC_END) { - ret = handle_vmalloc_fault(mm, address); + ret = handle_vmalloc_fault(address); if (unlikely(ret)) goto bad_area_nosemaphore; else diff --git a/arch/x86/kernel/cpu/perf_event.c b/arch/x86/kernel/cpu/perf_event.c index 9d84491..8a87a32 100644 --- a/arch/x86/kernel/cpu/perf_event.c +++ b/arch/x86/kernel/cpu/perf_event.c @@ -1276,16 +1276,16 @@ void perf_events_lapic_init(void) static int __kprobes perf_event_nmi_handler(unsigned int cmd, struct pt_regs *regs) { - int ret; u64 start_clock; u64 finish_clock; + int ret; if (!atomic_read(&active_events)) return NMI_DONE; - start_clock = local_clock(); + start_clock = sched_clock(); ret = x86_pmu.handle_irq(regs); - finish_clock = local_clock(); + finish_clock = sched_clock(); perf_sample_event_took(finish_clock - start_clock); diff --git a/arch/x86/kernel/nmi.c b/arch/x86/kernel/nmi.c index ba77ebc..6fcb49c 100644 --- a/arch/x86/kernel/nmi.c +++ b/arch/x86/kernel/nmi.c @@ -113,10 +113,10 @@ static int __kprobes nmi_handle(unsigned int type, struct pt_regs *regs, bool b2 u64 before, delta, whole_msecs; int remainder_ns, decimal_msecs, thishandled; - before = local_clock(); + before = sched_clock(); thishandled = a->handler(type, regs); handled += thishandled; - delta = local_clock() - before; + delta = sched_clock() - before; trace_nmi_handler(a->handler, (int)delta, thishandled); if (delta < nmi_longest_ns) diff --git a/drivers/clk/clk-nomadik.c b/drivers/clk/clk-nomadik.c index 51410c2..4d978a3 100644 --- a/drivers/clk/clk-nomadik.c +++ b/drivers/clk/clk-nomadik.c @@ -27,6 +27,14 @@ */ #define SRC_CR 0x00U +#define SRC_CR_T0_ENSEL BIT(15) +#define SRC_CR_T1_ENSEL BIT(17) +#define SRC_CR_T2_ENSEL BIT(19) +#define SRC_CR_T3_ENSEL BIT(21) +#define SRC_CR_T4_ENSEL BIT(23) +#define SRC_CR_T5_ENSEL BIT(25) +#define SRC_CR_T6_ENSEL BIT(27) +#define SRC_CR_T7_ENSEL BIT(29) #define SRC_XTALCR 0x0CU #define SRC_XTALCR_XTALTIMEN BIT(20) #define SRC_XTALCR_SXTALDIS BIT(19) @@ -543,6 +551,19 @@ void __init nomadik_clk_init(void) __func__, np->name); return; } + + /* Set all timers to use the 2.4 MHz TIMCLK */ + val = readl(src_base + SRC_CR); + val |= SRC_CR_T0_ENSEL; + val |= SRC_CR_T1_ENSEL; + val |= SRC_CR_T2_ENSEL; + val |= SRC_CR_T3_ENSEL; + val |= SRC_CR_T4_ENSEL; + val |= SRC_CR_T5_ENSEL; + val |= SRC_CR_T6_ENSEL; + val |= SRC_CR_T7_ENSEL; + writel(val, src_base + SRC_CR); + val = readl(src_base + SRC_XTALCR); pr_info("SXTALO is %s\n", (val & SRC_XTALCR_SXTALDIS) ? "disabled" : "enabled"); diff --git a/drivers/clk/mvebu/armada-370.c b/drivers/clk/mvebu/armada-370.c index fc777bd..81a202d 100644 --- a/drivers/clk/mvebu/armada-370.c +++ b/drivers/clk/mvebu/armada-370.c @@ -39,8 +39,8 @@ static const struct coreclk_ratio a370_coreclk_ratios[] __initconst = { }; static const u32 a370_tclk_freqs[] __initconst = { - 16600000, - 20000000, + 166000000, + 200000000, }; static u32 __init a370_get_tclk_freq(void __iomem *sar) diff --git a/drivers/clk/socfpga/clk.c b/drivers/clk/socfpga/clk.c index 5bb848c..81dd31a 100644 --- a/drivers/clk/socfpga/clk.c +++ b/drivers/clk/socfpga/clk.c @@ -49,7 +49,7 @@ #define SOCFPGA_L4_SP_CLK "l4_sp_clk" #define SOCFPGA_NAND_CLK "nand_clk" #define SOCFPGA_NAND_X_CLK "nand_x_clk" -#define SOCFPGA_MMC_CLK "mmc_clk" +#define SOCFPGA_MMC_CLK "sdmmc_clk" #define SOCFPGA_DB_CLK "gpio_db_clk" #define div_mask(width) ((1 << (width)) - 1) diff --git a/drivers/clk/versatile/clk-icst.c b/drivers/clk/versatile/clk-icst.c index 67ccf4a..f5e4c21 100644 --- a/drivers/clk/versatile/clk-icst.c +++ b/drivers/clk/versatile/clk-icst.c @@ -107,7 +107,7 @@ static int icst_set_rate(struct clk_hw *hw, unsigned long rate, vco = icst_hz_to_vco(icst->params, rate); icst->rate = icst_hz(icst->params, vco); - vco_set(icst->vcoreg, icst->lockreg, vco); + vco_set(icst->lockreg, icst->vcoreg, vco); return 0; } diff --git a/drivers/gpu/drm/i915/intel_crt.c b/drivers/gpu/drm/i915/intel_crt.c index db59bb9..10d1de5 100644 --- a/drivers/gpu/drm/i915/intel_crt.c +++ b/drivers/gpu/drm/i915/intel_crt.c @@ -107,8 +107,6 @@ static unsigned int intel_crt_get_flags(struct intel_encoder *encoder) static void intel_crt_get_config(struct intel_encoder *encoder, struct intel_crtc_config *pipe_config) { - struct drm_device *dev = encoder->base.dev; - pipe_config->adjusted_mode.flags |= intel_crt_get_flags(encoder); } diff --git a/drivers/gpu/drm/radeon/evergreen_hdmi.c b/drivers/gpu/drm/radeon/evergreen_hdmi.c index fe1de85..57fcc4b 100644 --- a/drivers/gpu/drm/radeon/evergreen_hdmi.c +++ b/drivers/gpu/drm/radeon/evergreen_hdmi.c @@ -291,6 +291,7 @@ void evergreen_hdmi_setmode(struct drm_encoder *encoder, struct drm_display_mode /* fglrx clears sth in AFMT_AUDIO_PACKET_CONTROL2 here */ WREG32(HDMI_ACR_PACKET_CONTROL + offset, + HDMI_ACR_SOURCE | /* select SW CTS value */ HDMI_ACR_AUTO_SEND); /* allow hw to sent ACR packets when required */ evergreen_hdmi_update_ACR(encoder, mode->clock); diff --git a/drivers/gpu/drm/radeon/kv_dpm.c b/drivers/gpu/drm/radeon/kv_dpm.c index 7139906..b419055 100644 --- a/drivers/gpu/drm/radeon/kv_dpm.c +++ b/drivers/gpu/drm/radeon/kv_dpm.c @@ -2635,7 +2635,7 @@ int kv_dpm_init(struct radeon_device *rdev) pi->caps_sclk_ds = true; pi->enable_auto_thermal_throttling = true; pi->disable_nb_ps3_in_battery = false; - pi->bapm_enable = true; + pi->bapm_enable = false; pi->voltage_drop_t = 0; pi->caps_sclk_throttle_low_notification = false; pi->caps_fps = false; /* true? */ diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index a400ac1..24f4960 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -1272,8 +1272,8 @@ struct radeon_blacklist_clocks struct radeon_clock_and_voltage_limits { u32 sclk; u32 mclk; - u32 vddc; - u32 vddci; + u16 vddc; + u16 vddci; }; struct radeon_clock_array { diff --git a/drivers/input/input.c b/drivers/input/input.c index c044699..e75d015 100644 --- a/drivers/input/input.c +++ b/drivers/input/input.c @@ -1734,6 +1734,7 @@ EXPORT_SYMBOL_GPL(input_class); */ struct input_dev *input_allocate_device(void) { + static atomic_t input_no = ATOMIC_INIT(0); struct input_dev *dev; dev = kzalloc(sizeof(struct input_dev), GFP_KERNEL); @@ -1743,9 +1744,13 @@ struct input_dev *input_allocate_device(void) device_initialize(&dev->dev); mutex_init(&dev->mutex); spin_lock_init(&dev->event_lock); + init_timer(&dev->timer); INIT_LIST_HEAD(&dev->h_list); INIT_LIST_HEAD(&dev->node); + dev_set_name(&dev->dev, "input%ld", + (unsigned long) atomic_inc_return(&input_no) - 1); + __module_get(THIS_MODULE); } @@ -2019,7 +2024,6 @@ static void devm_input_device_unregister(struct device *dev, void *res) */ int input_register_device(struct input_dev *dev) { - static atomic_t input_no = ATOMIC_INIT(0); struct input_devres *devres = NULL; struct input_handler *handler; unsigned int packet_size; @@ -2059,7 +2063,6 @@ int input_register_device(struct input_dev *dev) * If delay and period are pre-set by the driver, then autorepeating * is handled by the driver itself and we don't do it in input.c. */ - init_timer(&dev->timer); if (!dev->rep[REP_DELAY] && !dev->rep[REP_PERIOD]) { dev->timer.data = (long) dev; dev->timer.function = input_repeat_key; @@ -2073,9 +2076,6 @@ int input_register_device(struct input_dev *dev) if (!dev->setkeycode) dev->setkeycode = input_default_setkeycode; - dev_set_name(&dev->dev, "input%ld", - (unsigned long) atomic_inc_return(&input_no) - 1); - error = device_add(&dev->dev); if (error) goto err_free_vals; diff --git a/drivers/input/keyboard/pxa27x_keypad.c b/drivers/input/keyboard/pxa27x_keypad.c index 134c3b4..a2e758d 100644 --- a/drivers/input/keyboard/pxa27x_keypad.c +++ b/drivers/input/keyboard/pxa27x_keypad.c @@ -786,10 +786,17 @@ static int pxa27x_keypad_probe(struct platform_device *pdev) input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REP); input_set_capability(input_dev, EV_MSC, MSC_SCAN); - if (pdata) + if (pdata) { error = pxa27x_keypad_build_keycode(keypad); - else + } else { error = pxa27x_keypad_build_keycode_from_dt(keypad); + /* + * Data that we get from DT resides in dynamically + * allocated memory so we need to update our pdata + * pointer. + */ + pdata = keypad->pdata; + } if (error) { dev_err(&pdev->dev, "failed to build keycode\n"); goto failed_put_clk; diff --git a/drivers/input/misc/cm109.c b/drivers/input/misc/cm109.c index 082684e..9365535 100644 --- a/drivers/input/misc/cm109.c +++ b/drivers/input/misc/cm109.c @@ -351,7 +351,9 @@ static void cm109_urb_irq_callback(struct urb *urb) if (status) { if (status == -ESHUTDOWN) return; - dev_err(&dev->intf->dev, "%s: urb status %d\n", __func__, status); + dev_err_ratelimited(&dev->intf->dev, "%s: urb status %d\n", + __func__, status); + goto out; } /* Special keys */ @@ -418,8 +420,12 @@ static void cm109_urb_ctl_callback(struct urb *urb) dev->ctl_data->byte[2], dev->ctl_data->byte[3]); - if (status) - dev_err(&dev->intf->dev, "%s: urb status %d\n", __func__, status); + if (status) { + if (status == -ESHUTDOWN) + return; + dev_err_ratelimited(&dev->intf->dev, "%s: urb status %d\n", + __func__, status); + } spin_lock(&dev->ctl_submit_lock); @@ -427,7 +433,7 @@ static void cm109_urb_ctl_callback(struct urb *urb) if (likely(!dev->shutdown)) { - if (dev->buzzer_pending) { + if (dev->buzzer_pending || status) { dev->buzzer_pending = 0; dev->ctl_urb_pending = 1; cm109_submit_buzz_toggle(dev); diff --git a/drivers/input/mouse/alps.c b/drivers/input/mouse/alps.c index 7c5d72a..8365847 100644 --- a/drivers/input/mouse/alps.c +++ b/drivers/input/mouse/alps.c @@ -103,6 +103,7 @@ static const struct alps_model_info alps_model_data[] = { /* Dell Latitude E5500, E6400, E6500, Precision M4400 */ { { 0x62, 0x02, 0x14 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_PASS | ALPS_DUALPOINT | ALPS_PS2_INTERLEAVED }, + { { 0x73, 0x00, 0x14 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_DUALPOINT }, /* Dell XT2 */ { { 0x73, 0x02, 0x50 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_FOUR_BUTTONS }, /* Dell Vostro 1400 */ { { 0x52, 0x01, 0x14 }, 0x00, ALPS_PROTO_V2, 0xff, 0xff, ALPS_PASS | ALPS_DUALPOINT | ALPS_PS2_INTERLEAVED }, /* Toshiba Tecra A11-11L */ diff --git a/drivers/input/serio/i8042.c b/drivers/input/serio/i8042.c index 78e4de4..52c9ebf 100644 --- a/drivers/input/serio/i8042.c +++ b/drivers/input/serio/i8042.c @@ -223,21 +223,26 @@ static int i8042_flush(void) { unsigned long flags; unsigned char data, str; - int i = 0; + int count = 0; + int retval = 0; spin_lock_irqsave(&i8042_lock, flags); - while (((str = i8042_read_status()) & I8042_STR_OBF) && (i < I8042_BUFFER_SIZE)) { - udelay(50); - data = i8042_read_data(); - i++; - dbg("%02x <- i8042 (flush, %s)\n", - data, str & I8042_STR_AUXDATA ? "aux" : "kbd"); + while ((str = i8042_read_status()) & I8042_STR_OBF) { + if (count++ < I8042_BUFFER_SIZE) { + udelay(50); + data = i8042_read_data(); + dbg("%02x <- i8042 (flush, %s)\n", + data, str & I8042_STR_AUXDATA ? "aux" : "kbd"); + } else { + retval = -EIO; + break; + } } spin_unlock_irqrestore(&i8042_lock, flags); - return i; + return retval; } /* @@ -849,7 +854,7 @@ static int __init i8042_check_aux(void) static int i8042_controller_check(void) { - if (i8042_flush() == I8042_BUFFER_SIZE) { + if (i8042_flush()) { pr_err("No controller found\n"); return -ENODEV; } diff --git a/drivers/input/tablet/wacom_sys.c b/drivers/input/tablet/wacom_sys.c index 79b69ea..e53416a 100644 --- a/drivers/input/tablet/wacom_sys.c +++ b/drivers/input/tablet/wacom_sys.c @@ -1031,6 +1031,7 @@ static void wacom_destroy_leds(struct wacom *wacom) } static enum power_supply_property wacom_battery_props[] = { + POWER_SUPPLY_PROP_SCOPE, POWER_SUPPLY_PROP_CAPACITY }; @@ -1042,6 +1043,9 @@ static int wacom_battery_get_property(struct power_supply *psy, int ret = 0; switch (psp) { + case POWER_SUPPLY_PROP_SCOPE: + val->intval = POWER_SUPPLY_SCOPE_DEVICE; + break; case POWER_SUPPLY_PROP_CAPACITY: val->intval = wacom->wacom_wac.battery_capacity * 100 / 31; diff --git a/drivers/input/tablet/wacom_wac.c b/drivers/input/tablet/wacom_wac.c index b2aa503..c59b797 100644 --- a/drivers/input/tablet/wacom_wac.c +++ b/drivers/input/tablet/wacom_wac.c @@ -2054,6 +2054,12 @@ static const struct wacom_features wacom_features_0x101 = static const struct wacom_features wacom_features_0x10D = { "Wacom ISDv4 10D", WACOM_PKGLEN_MTTPC, 26202, 16325, 255, 0, MTTPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES }; +static const struct wacom_features wacom_features_0x10E = + { "Wacom ISDv4 10E", WACOM_PKGLEN_MTTPC, 27760, 15694, 255, + 0, MTTPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES }; +static const struct wacom_features wacom_features_0x10F = + { "Wacom ISDv4 10F", WACOM_PKGLEN_MTTPC, 27760, 15694, 255, + 0, MTTPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES }; static const struct wacom_features wacom_features_0x4001 = { "Wacom ISDv4 4001", WACOM_PKGLEN_MTTPC, 26202, 16325, 255, 0, MTTPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES }; @@ -2248,6 +2254,8 @@ const struct usb_device_id wacom_ids[] = { { USB_DEVICE_WACOM(0x100) }, { USB_DEVICE_WACOM(0x101) }, { USB_DEVICE_WACOM(0x10D) }, + { USB_DEVICE_WACOM(0x10E) }, + { USB_DEVICE_WACOM(0x10F) }, { USB_DEVICE_WACOM(0x300) }, { USB_DEVICE_WACOM(0x301) }, { USB_DEVICE_WACOM(0x304) }, diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c index be12fbf..1ea7523 100644 --- a/drivers/pci/hotplug/acpiphp_glue.c +++ b/drivers/pci/hotplug/acpiphp_glue.c @@ -552,9 +552,8 @@ static void __ref enable_slot(struct acpiphp_slot *slot) struct acpiphp_func *func; int max, pass; LIST_HEAD(add_list); - int nr_found; - nr_found = acpiphp_rescan_slot(slot); + acpiphp_rescan_slot(slot); max = acpiphp_max_busnr(bus); for (pass = 0; pass < 2; pass++) { list_for_each_entry(dev, &bus->devices, bus_list) { @@ -574,9 +573,6 @@ static void __ref enable_slot(struct acpiphp_slot *slot) } } __pci_bus_assign_resources(bus, &add_list, NULL); - /* Nothing more to do here if there are no new devices on this bus. */ - if (!nr_found && (slot->flags & SLOT_ENABLED)) - return; acpiphp_sanitize_bus(bus); acpiphp_set_hpp_values(bus); diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index c45f9c0..b21d553 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -904,6 +904,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_LUMEL_PD12_PID) }, /* Crucible Devices */ { USB_DEVICE(FTDI_VID, FTDI_CT_COMET_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_Z3X_PID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index 1b8af46..a7019d1 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -1307,3 +1307,9 @@ * Manufacturer: Crucible Technologies */ #define FTDI_CT_COMET_PID 0x8e08 + +/* + * Product: Z3X Box + * Manufacturer: Smart GSM Team + */ +#define FTDI_Z3X_PID 0x0011 diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index bedf8e4..1e6de4c 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -4,11 +4,6 @@ * Copyright (C) 2001-2007 Greg Kroah-Hartman (greg@kroah.com) * Copyright (C) 2003 IBM Corp. * - * Copyright (C) 2009, 2013 Frank Schäfer <fschaefer.oss@googlemail.com> - * - fixes, improvements and documentation for the baud rate encoding methods - * Copyright (C) 2013 Reinhard Max <max@suse.de> - * - fixes and improvements for the divisor based baud rate encoding method - * * Original driver for 2.2.x by anonymous * * This program is free software; you can redistribute it and/or @@ -134,18 +129,10 @@ MODULE_DEVICE_TABLE(usb, id_table); enum pl2303_type { - type_0, /* H version ? */ - type_1, /* H version ? */ - HX_TA, /* HX(A) / X(A) / TA version */ /* TODO: improve */ - HXD_EA_RA_SA, /* HXD / EA / RA / SA version */ /* TODO: improve */ - TB, /* TB version */ - HX_CLONE, /* Cheap and less functional clone of the HX chip */ + type_0, /* don't know the difference between type 0 and */ + type_1, /* type 1, until someone from prolific tells us... */ + HX, /* HX version of the pl2303 chip */ }; -/* - * NOTE: don't know the difference between type 0 and type 1, - * until someone from Prolific tells us... - * TODO: distinguish between X/HX, TA and HXD, EA, RA, SA variants - */ struct pl2303_serial_private { enum pl2303_type type; @@ -185,7 +172,6 @@ static int pl2303_startup(struct usb_serial *serial) { struct pl2303_serial_private *spriv; enum pl2303_type type = type_0; - char *type_str = "unknown (treating as type_0)"; unsigned char *buf; spriv = kzalloc(sizeof(*spriv), GFP_KERNEL); @@ -198,53 +184,15 @@ static int pl2303_startup(struct usb_serial *serial) return -ENOMEM; } - if (serial->dev->descriptor.bDeviceClass == 0x02) { + if (serial->dev->descriptor.bDeviceClass == 0x02) type = type_0; - type_str = "type_0"; - } else if (serial->dev->descriptor.bMaxPacketSize0 == 0x40) { - /* - * NOTE: The bcdDevice version is the only difference between - * the device descriptors of the X/HX, HXD, EA, RA, SA, TA, TB - */ - if (le16_to_cpu(serial->dev->descriptor.bcdDevice) == 0x300) { - /* Check if the device is a clone */ - pl2303_vendor_read(0x9494, 0, serial, buf); - /* - * NOTE: Not sure if this read is really needed. - * The HX returns 0x00, the clone 0x02, but the Windows - * driver seems to ignore the value and continues. - */ - pl2303_vendor_write(0x0606, 0xaa, serial); - pl2303_vendor_read(0x8686, 0, serial, buf); - if (buf[0] != 0xaa) { - type = HX_CLONE; - type_str = "X/HX clone (limited functionality)"; - } else { - type = HX_TA; - type_str = "X/HX/TA"; - } - pl2303_vendor_write(0x0606, 0x00, serial); - } else if (le16_to_cpu(serial->dev->descriptor.bcdDevice) - == 0x400) { - type = HXD_EA_RA_SA; - type_str = "HXD/EA/RA/SA"; - } else if (le16_to_cpu(serial->dev->descriptor.bcdDevice) - == 0x500) { - type = TB; - type_str = "TB"; - } else { - dev_info(&serial->interface->dev, - "unknown/unsupported device type\n"); - kfree(spriv); - kfree(buf); - return -ENODEV; - } - } else if (serial->dev->descriptor.bDeviceClass == 0x00 - || serial->dev->descriptor.bDeviceClass == 0xFF) { + else if (serial->dev->descriptor.bMaxPacketSize0 == 0x40) + type = HX; + else if (serial->dev->descriptor.bDeviceClass == 0x00) type = type_1; - type_str = "type_1"; - } - dev_dbg(&serial->interface->dev, "device type: %s\n", type_str); + else if (serial->dev->descriptor.bDeviceClass == 0xFF) + type = type_1; + dev_dbg(&serial->interface->dev, "device type: %d\n", type); spriv->type = type; usb_set_serial_data(serial, spriv); @@ -259,10 +207,10 @@ static int pl2303_startup(struct usb_serial *serial) pl2303_vendor_read(0x8383, 0, serial, buf); pl2303_vendor_write(0, 1, serial); pl2303_vendor_write(1, 0, serial); - if (type == type_0 || type == type_1) - pl2303_vendor_write(2, 0x24, serial); - else + if (type == HX) pl2303_vendor_write(2, 0x44, serial); + else + pl2303_vendor_write(2, 0x24, serial); kfree(buf); return 0; @@ -316,174 +264,65 @@ static int pl2303_set_control_lines(struct usb_serial_port *port, u8 value) return retval; } -static int pl2303_baudrate_encode_direct(int baud, enum pl2303_type type, - u8 buf[4]) +static void pl2303_encode_baudrate(struct tty_struct *tty, + struct usb_serial_port *port, + u8 buf[4]) { - /* - * NOTE: Only the values defined in baud_sup are supported ! - * => if unsupported values are set, the PL2303 uses 9600 baud instead - * => HX clones just don't work at unsupported baud rates < 115200 baud, - * for baud rates > 115200 they run at 115200 baud - */ const int baud_sup[] = { 75, 150, 300, 600, 1200, 1800, 2400, 3600, - 4800, 7200, 9600, 14400, 19200, 28800, 38400, - 57600, 115200, 230400, 460800, 614400, 921600, - 1228800, 2457600, 3000000, 6000000, 12000000 }; + 4800, 7200, 9600, 14400, 19200, 28800, 38400, + 57600, 115200, 230400, 460800, 500000, 614400, + 921600, 1228800, 2457600, 3000000, 6000000 }; + + struct usb_serial *serial = port->serial; + struct pl2303_serial_private *spriv = usb_get_serial_data(serial); + int baud; + int i; + /* - * NOTE: With the exception of type_0/1 devices, the following - * additional baud rates are supported (tested with HX rev. 3A only): - * 110*, 56000*, 128000, 134400, 161280, 201600, 256000*, 268800, - * 403200, 806400. (*: not HX and HX clones) - * - * Maximum values: HXD, TB: 12000000; HX, TA: 6000000; - * type_0+1: 1228800; RA: 921600; HX clones, SA: 115200 - * - * As long as we are not using this encoding method for anything else - * than the type_0+1, HX and HX clone chips, there is no point in - * complicating the code to support them. + * NOTE: Only the values defined in baud_sup are supported! + * => if unsupported values are set, the PL2303 seems to use + * 9600 baud (at least my PL2303X always does) */ - int i; + baud = tty_get_baud_rate(tty); + dev_dbg(&port->dev, "baud requested = %d\n", baud); + if (!baud) + return; /* Set baudrate to nearest supported value */ for (i = 0; i < ARRAY_SIZE(baud_sup); ++i) { if (baud_sup[i] > baud) break; } + if (i == ARRAY_SIZE(baud_sup)) baud = baud_sup[i - 1]; else if (i > 0 && (baud_sup[i] - baud) > (baud - baud_sup[i - 1])) baud = baud_sup[i - 1]; else baud = baud_sup[i]; - /* Respect the chip type specific baud rate limits */ - /* - * FIXME: as long as we don't know how to distinguish between the - * HXD, EA, RA, and SA chip variants, allow the max. value of 12M. - */ - if (type == HX_TA) - baud = min_t(int, baud, 6000000); - else if (type == type_0 || type == type_1) - baud = min_t(int, baud, 1228800); - else if (type == HX_CLONE) - baud = min_t(int, baud, 115200); - /* Direct (standard) baud rate encoding method */ - put_unaligned_le32(baud, buf); - - return baud; -} -static int pl2303_baudrate_encode_divisor(int baud, enum pl2303_type type, - u8 buf[4]) -{ - /* - * Divisor based baud rate encoding method - * - * NOTE: HX clones do NOT support this method. - * It's not clear if the type_0/1 chips support it. - * - * divisor = 12MHz * 32 / baudrate = 2^A * B - * - * with - * - * A = buf[1] & 0x0e - * B = buf[0] + (buf[1] & 0x01) << 8 - * - * Special cases: - * => 8 < B < 16: device seems to work not properly - * => B <= 8: device uses the max. value B = 512 instead - */ - unsigned int A, B; + /* type_0, type_1 only support up to 1228800 baud */ + if (spriv->type != HX) + baud = min_t(int, baud, 1228800); - /* - * NOTE: The Windows driver allows maximum baud rates of 110% of the - * specified maximium value. - * Quick tests with early (2004) HX (rev. A) chips suggest, that even - * higher baud rates (up to the maximum of 24M baud !) are working fine, - * but that should really be tested carefully in "real life" scenarios - * before removing the upper limit completely. - * Baud rates smaller than the specified 75 baud are definitely working - * fine. - */ - if (type == type_0 || type == type_1) - baud = min_t(int, baud, 1228800 * 1.1); - else if (type == HX_TA) - baud = min_t(int, baud, 6000000 * 1.1); - else if (type == HXD_EA_RA_SA) - /* HXD, EA: 12Mbps; RA: 1Mbps; SA: 115200 bps */ - /* - * FIXME: as long as we don't know how to distinguish between - * these chip variants, allow the max. of these values - */ - baud = min_t(int, baud, 12000000 * 1.1); - else if (type == TB) - baud = min_t(int, baud, 12000000 * 1.1); - /* Determine factors A and B */ - A = 0; - B = 12000000 * 32 / baud; /* 12MHz */ - B <<= 1; /* Add one bit for rounding */ - while (B > (512 << 1) && A <= 14) { - A += 2; - B >>= 2; - } - if (A > 14) { /* max. divisor = min. baudrate reached */ - A = 14; - B = 512; - /* => ~45.78 baud */ + if (baud <= 115200) { + put_unaligned_le32(baud, buf); } else { - B = (B + 1) >> 1; /* Round the last bit */ - } - /* Handle special cases */ - if (B == 512) - B = 0; /* also: 1 to 8 */ - else if (B < 16) /* - * NOTE: With the current algorithm this happens - * only for A=0 and means that the min. divisor - * (respectively: the max. baudrate) is reached. + * Apparently the formula for higher speeds is: + * baudrate = 12M * 32 / (2^buf[1]) / buf[0] */ - B = 16; /* => 24 MBaud */ - /* Encode the baud rate */ - buf[3] = 0x80; /* Select divisor encoding method */ - buf[2] = 0; - buf[1] = (A & 0x0e); /* A */ - buf[1] |= ((B & 0x100) >> 8); /* MSB of B */ - buf[0] = B & 0xff; /* 8 LSBs of B */ - /* Calculate the actual/resulting baud rate */ - if (B <= 8) - B = 512; - baud = 12000000 * 32 / ((1 << A) * B); - - return baud; -} - -static void pl2303_encode_baudrate(struct tty_struct *tty, - struct usb_serial_port *port, - enum pl2303_type type, - u8 buf[4]) -{ - int baud; + unsigned tmp = 12000000 * 32 / baud; + buf[3] = 0x80; + buf[2] = 0; + buf[1] = (tmp >= 256); + while (tmp >= 256) { + tmp >>= 2; + buf[1] <<= 1; + } + buf[0] = tmp; + } - baud = tty_get_baud_rate(tty); - dev_dbg(&port->dev, "baud requested = %d\n", baud); - if (!baud) - return; - /* - * There are two methods for setting/encoding the baud rate - * 1) Direct method: encodes the baud rate value directly - * => supported by all chip types - * 2) Divisor based method: encodes a divisor to a base value (12MHz*32) - * => not supported by HX clones (and likely type_0/1 chips) - * - * NOTE: Although the divisor based baud rate encoding method is much - * more flexible, some of the standard baud rate values can not be - * realized exactly. But the difference is very small (max. 0.2%) and - * the device likely uses the same baud rate generator for both methods - * so that there is likley no difference. - */ - if (type == type_0 || type == type_1 || type == HX_CLONE) - baud = pl2303_baudrate_encode_direct(baud, type, buf); - else - baud = pl2303_baudrate_encode_divisor(baud, type, buf); /* Save resulting baud rate */ tty_encode_baud_rate(tty, baud, baud); dev_dbg(&port->dev, "baud set = %d\n", baud); @@ -540,8 +379,8 @@ static void pl2303_set_termios(struct tty_struct *tty, dev_dbg(&port->dev, "data bits = %d\n", buf[6]); } - /* For reference: buf[0]:buf[3] baud rate value */ - pl2303_encode_baudrate(tty, port, spriv->type, buf); + /* For reference buf[0]:buf[3] baud rate value */ + pl2303_encode_baudrate(tty, port, &buf[0]); /* For reference buf[4]=0 is 1 stop bits */ /* For reference buf[4]=1 is 1.5 stop bits */ @@ -618,10 +457,10 @@ static void pl2303_set_termios(struct tty_struct *tty, dev_dbg(&port->dev, "0xa1:0x21:0:0 %d - %7ph\n", i, buf); if (C_CRTSCTS(tty)) { - if (spriv->type == type_0 || spriv->type == type_1) - pl2303_vendor_write(0x0, 0x41, serial); - else + if (spriv->type == HX) pl2303_vendor_write(0x0, 0x61, serial); + else + pl2303_vendor_write(0x0, 0x41, serial); } else { pl2303_vendor_write(0x0, 0x0, serial); } @@ -658,7 +497,7 @@ static int pl2303_open(struct tty_struct *tty, struct usb_serial_port *port) struct pl2303_serial_private *spriv = usb_get_serial_data(serial); int result; - if (spriv->type == type_0 || spriv->type == type_1) { + if (spriv->type != HX) { usb_clear_halt(serial->dev, port->write_urb->pipe); usb_clear_halt(serial->dev, port->read_urb->pipe); } else { @@ -833,7 +672,6 @@ static void pl2303_break_ctl(struct tty_struct *tty, int break_state) result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), BREAK_REQUEST, BREAK_REQUEST_TYPE, state, 0, NULL, 0, 100); - /* NOTE: HX clones don't support sending breaks, -EPIPE is returned */ if (result) dev_err(&port->dev, "error sending break = %d\n", result); } diff --git a/fs/dcache.c b/fs/dcache.c index 20532cb..ae6ebb8 100644 --- a/fs/dcache.c +++ b/fs/dcache.c @@ -542,7 +542,7 @@ EXPORT_SYMBOL(d_drop); * If ref is non-zero, then decrement the refcount too. * Returns dentry requiring refcount drop, or NULL if we're done. */ -static inline struct dentry * +static struct dentry * dentry_kill(struct dentry *dentry, int unlock_on_failure) __releases(dentry->d_lock) { @@ -630,7 +630,8 @@ repeat: goto kill_it; } - dentry->d_flags |= DCACHE_REFERENCED; + if (!(dentry->d_flags & DCACHE_REFERENCED)) + dentry->d_flags |= DCACHE_REFERENCED; dentry_lru_add(dentry); dentry->d_lockref.count--; diff --git a/fs/eventpoll.c b/fs/eventpoll.c index 473e09d..810c28f 100644 --- a/fs/eventpoll.c +++ b/fs/eventpoll.c @@ -34,7 +34,6 @@ #include <linux/mutex.h> #include <linux/anon_inodes.h> #include <linux/device.h> -#include <linux/freezer.h> #include <asm/uaccess.h> #include <asm/io.h> #include <asm/mman.h> @@ -1605,8 +1604,7 @@ fetch_events: } spin_unlock_irqrestore(&ep->lock, flags); - if (!freezable_schedule_hrtimeout_range(to, slack, - HRTIMER_MODE_ABS)) + if (!schedule_hrtimeout_range(to, slack, HRTIMER_MODE_ABS)) timed_out = 1; spin_lock_irqsave(&ep->lock, flags); diff --git a/fs/select.c b/fs/select.c index 35d4adc7..dfd5cb1 100644 --- a/fs/select.c +++ b/fs/select.c @@ -238,8 +238,7 @@ int poll_schedule_timeout(struct poll_wqueues *pwq, int state, set_current_state(state); if (!pwq->triggered) - rc = freezable_schedule_hrtimeout_range(expires, slack, - HRTIMER_MODE_ABS); + rc = schedule_hrtimeout_range(expires, slack, HRTIMER_MODE_ABS); __set_current_state(TASK_RUNNING); /* diff --git a/include/uapi/linux/perf_event.h b/include/uapi/linux/perf_event.h index 009a655..2fc1602 100644 --- a/include/uapi/linux/perf_event.h +++ b/include/uapi/linux/perf_event.h @@ -456,13 +456,15 @@ struct perf_event_mmap_page { /* * Control data for the mmap() data buffer. * - * User-space reading the @data_head value should issue an rmb(), on - * SMP capable platforms, after reading this value -- see - * perf_event_wakeup(). + * User-space reading the @data_head value should issue an smp_rmb(), + * after reading this value. * * When the mapping is PROT_WRITE the @data_tail value should be - * written by userspace to reflect the last read data. In this case - * the kernel will not over-write unread data. + * written by userspace to reflect the last read data, after issueing + * an smp_mb() to separate the data read from the ->data_tail store. + * In this case the kernel will not over-write unread data. + * + * See perf_output_put_handle() for the data ordering. */ __u64 data_head; /* head in the data section */ __u64 data_tail; /* user-space written tail */ diff --git a/kernel/events/ring_buffer.c b/kernel/events/ring_buffer.c index cd55144..9c2ddfb 100644 --- a/kernel/events/ring_buffer.c +++ b/kernel/events/ring_buffer.c @@ -87,10 +87,31 @@ again: goto out; /* - * Publish the known good head. Rely on the full barrier implied - * by atomic_dec_and_test() order the rb->head read and this - * write. + * Since the mmap() consumer (userspace) can run on a different CPU: + * + * kernel user + * + * READ ->data_tail READ ->data_head + * smp_mb() (A) smp_rmb() (C) + * WRITE $data READ $data + * smp_wmb() (B) smp_mb() (D) + * STORE ->data_head WRITE ->data_tail + * + * Where A pairs with D, and B pairs with C. + * + * I don't think A needs to be a full barrier because we won't in fact + * write data until we see the store from userspace. So we simply don't + * issue the data WRITE until we observe it. Be conservative for now. + * + * OTOH, D needs to be a full barrier since it separates the data READ + * from the tail WRITE. + * + * For B a WMB is sufficient since it separates two WRITEs, and for C + * an RMB is sufficient since it separates two READs. + * + * See perf_output_begin(). */ + smp_wmb(); rb->user_page->data_head = head; /* @@ -154,9 +175,11 @@ int perf_output_begin(struct perf_output_handle *handle, * Userspace could choose to issue a mb() before updating the * tail pointer. So that all reads will be completed before the * write is issued. + * + * See perf_output_put_handle(). */ tail = ACCESS_ONCE(rb->user_page->data_tail); - smp_rmb(); + smp_mb(); offset = head = local_read(&rb->head); head += size; if (unlikely(!perf_output_space(rb, tail, offset, head))) diff --git a/lib/scatterlist.c b/lib/scatterlist.c index a685c8a..d16fa29 100644 --- a/lib/scatterlist.c +++ b/lib/scatterlist.c @@ -577,7 +577,8 @@ void sg_miter_stop(struct sg_mapping_iter *miter) miter->__offset += miter->consumed; miter->__remaining -= miter->consumed; - if (miter->__flags & SG_MITER_TO_SG) + if ((miter->__flags & SG_MITER_TO_SG) && + !PageSlab(miter->page)) flush_kernel_dcache_page(miter->page); if (miter->__flags & SG_MITER_ATOMIC) { diff --git a/mm/huge_memory.c b/mm/huge_memory.c index 610e3df..cca80d9 100644 --- a/mm/huge_memory.c +++ b/mm/huge_memory.c @@ -1278,64 +1278,90 @@ out: int do_huge_pmd_numa_page(struct mm_struct *mm, struct vm_area_struct *vma, unsigned long addr, pmd_t pmd, pmd_t *pmdp) { + struct anon_vma *anon_vma = NULL; struct page *page; unsigned long haddr = addr & HPAGE_PMD_MASK; + int page_nid = -1, this_nid = numa_node_id(); int target_nid; - int current_nid = -1; - bool migrated; + bool page_locked; + bool migrated = false; spin_lock(&mm->page_table_lock); if (unlikely(!pmd_same(pmd, *pmdp))) goto out_unlock; page = pmd_page(pmd); - get_page(page); - current_nid = page_to_nid(page); + page_nid = page_to_nid(page); count_vm_numa_event(NUMA_HINT_FAULTS); - if (current_nid == numa_node_id()) + if (page_nid == this_nid) count_vm_numa_event(NUMA_HINT_FAULTS_LOCAL); + /* + * Acquire the page lock to serialise THP migrations but avoid dropping + * page_table_lock if at all possible + */ + page_locked = trylock_page(page); target_nid = mpol_misplaced(page, vma, haddr); if (target_nid == -1) { - put_page(page); - goto clear_pmdnuma; + /* If the page was locked, there are no parallel migrations */ + if (page_locked) + goto clear_pmdnuma; + + /* + * Otherwise wait for potential migrations and retry. We do + * relock and check_same as the page may no longer be mapped. + * As the fault is being retried, do not account for it. + */ + spin_unlock(&mm->page_table_lock); + wait_on_page_locked(page); + page_nid = -1; + goto out; } - /* Acquire the page lock to serialise THP migrations */ + /* Page is misplaced, serialise migrations and parallel THP splits */ + get_page(page); spin_unlock(&mm->page_table_lock); - lock_page(page); + if (!page_locked) + lock_page(page); + anon_vma = page_lock_anon_vma_read(page); /* Confirm the PTE did not while locked */ spin_lock(&mm->page_table_lock); if (unlikely(!pmd_same(pmd, *pmdp))) { unlock_page(page); put_page(page); + page_nid = -1; goto out_unlock; } - spin_unlock(&mm->page_table_lock); - /* Migrate the THP to the requested node */ + /* + * Migrate the THP to the requested node, returns with page unlocked + * and pmd_numa cleared. + */ + spin_unlock(&mm->page_table_lock); migrated = migrate_misplaced_transhuge_page(mm, vma, pmdp, pmd, addr, page, target_nid); - if (!migrated) - goto check_same; - - task_numa_fault(target_nid, HPAGE_PMD_NR, true); - return 0; + if (migrated) + page_nid = target_nid; -check_same: - spin_lock(&mm->page_table_lock); - if (unlikely(!pmd_same(pmd, *pmdp))) - goto out_unlock; + goto out; clear_pmdnuma: + BUG_ON(!PageLocked(page)); pmd = pmd_mknonnuma(pmd); set_pmd_at(mm, haddr, pmdp, pmd); VM_BUG_ON(pmd_numa(*pmdp)); update_mmu_cache_pmd(vma, addr, pmdp); + unlock_page(page); out_unlock: spin_unlock(&mm->page_table_lock); - if (current_nid != -1) - task_numa_fault(current_nid, HPAGE_PMD_NR, false); + +out: + if (anon_vma) + page_unlock_anon_vma_read(anon_vma); + + if (page_nid != -1) + task_numa_fault(page_nid, HPAGE_PMD_NR, migrated); + return 0; } diff --git a/mm/memcontrol.c b/mm/memcontrol.c index 497ec33..13b9d0f 100644 --- a/mm/memcontrol.c +++ b/mm/memcontrol.c @@ -54,6 +54,7 @@ #include <linux/page_cgroup.h> #include <linux/cpu.h> #include <linux/oom.h> +#include <linux/lockdep.h> #include "internal.h" #include <net/sock.h> #include <net/ip.h> @@ -2046,6 +2047,12 @@ static int mem_cgroup_soft_reclaim(struct mem_cgroup *root_memcg, return total; } +#ifdef CONFIG_LOCKDEP +static struct lockdep_map memcg_oom_lock_dep_map = { + .name = "memcg_oom_lock", +}; +#endif + static DEFINE_SPINLOCK(memcg_oom_lock); /* @@ -2083,7 +2090,8 @@ static bool mem_cgroup_oom_trylock(struct mem_cgroup *memcg) } iter->oom_lock = false; } - } + } else + mutex_acquire(&memcg_oom_lock_dep_map, 0, 1, _RET_IP_); spin_unlock(&memcg_oom_lock); @@ -2095,6 +2103,7 @@ static void mem_cgroup_oom_unlock(struct mem_cgroup *memcg) struct mem_cgroup *iter; spin_lock(&memcg_oom_lock); + mutex_release(&memcg_oom_lock_dep_map, 1, _RET_IP_); for_each_mem_cgroup_tree(iter, memcg) iter->oom_lock = false; spin_unlock(&memcg_oom_lock); @@ -2765,10 +2774,10 @@ done: *ptr = memcg; return 0; nomem: - *ptr = NULL; - if (gfp_mask & __GFP_NOFAIL) - return 0; - return -ENOMEM; + if (!(gfp_mask & __GFP_NOFAIL)) { + *ptr = NULL; + return -ENOMEM; + } bypass: *ptr = root_mem_cgroup; return -EINTR; @@ -3773,7 +3782,6 @@ void mem_cgroup_move_account_page_stat(struct mem_cgroup *from, { /* Update stat data for mem_cgroup */ preempt_disable(); - WARN_ON_ONCE(from->stat->count[idx] < nr_pages); __this_cpu_sub(from->stat->count[idx], nr_pages); __this_cpu_add(to->stat->count[idx], nr_pages); preempt_enable(); @@ -4950,31 +4958,18 @@ static void mem_cgroup_reparent_charges(struct mem_cgroup *memcg) } while (usage > 0); } -/* - * This mainly exists for tests during the setting of set of use_hierarchy. - * Since this is the very setting we are changing, the current hierarchy value - * is meaningless - */ -static inline bool __memcg_has_children(struct mem_cgroup *memcg) -{ - struct cgroup_subsys_state *pos; - - /* bounce at first found */ - css_for_each_child(pos, &memcg->css) - return true; - return false; -} - -/* - * Must be called with memcg_create_mutex held, unless the cgroup is guaranteed - * to be already dead (as in mem_cgroup_force_empty, for instance). This is - * from mem_cgroup_count_children(), in the sense that we don't really care how - * many children we have; we only need to know if we have any. It also counts - * any memcg without hierarchy as infertile. - */ static inline bool memcg_has_children(struct mem_cgroup *memcg) { - return memcg->use_hierarchy && __memcg_has_children(memcg); + lockdep_assert_held(&memcg_create_mutex); + /* + * The lock does not prevent addition or deletion to the list + * of children, but it prevents a new child from being + * initialized based on this parent in css_online(), so it's + * enough to decide whether hierarchically inherited + * attributes can still be changed or not. + */ + return memcg->use_hierarchy && + !list_empty(&memcg->css.cgroup->children); } /* @@ -5054,7 +5049,7 @@ static int mem_cgroup_hierarchy_write(struct cgroup_subsys_state *css, */ if ((!parent_memcg || !parent_memcg->use_hierarchy) && (val == 1 || val == 0)) { - if (!__memcg_has_children(memcg)) + if (list_empty(&memcg->css.cgroup->children)) memcg->use_hierarchy = val; else retval = -EBUSY; diff --git a/mm/memory.c b/mm/memory.c index 1311f26..d176154 100644 --- a/mm/memory.c +++ b/mm/memory.c @@ -3521,12 +3521,12 @@ static int do_nonlinear_fault(struct mm_struct *mm, struct vm_area_struct *vma, } int numa_migrate_prep(struct page *page, struct vm_area_struct *vma, - unsigned long addr, int current_nid) + unsigned long addr, int page_nid) { get_page(page); count_vm_numa_event(NUMA_HINT_FAULTS); - if (current_nid == numa_node_id()) + if (page_nid == numa_node_id()) count_vm_numa_event(NUMA_HINT_FAULTS_LOCAL); return mpol_misplaced(page, vma, addr); @@ -3537,7 +3537,7 @@ int do_numa_page(struct mm_struct *mm, struct vm_area_struct *vma, { struct page *page = NULL; spinlock_t *ptl; - int current_nid = -1; + int page_nid = -1; int target_nid; bool migrated = false; @@ -3567,15 +3567,10 @@ int do_numa_page(struct mm_struct *mm, struct vm_area_struct *vma, return 0; } - current_nid = page_to_nid(page); - target_nid = numa_migrate_prep(page, vma, addr, current_nid); + page_nid = page_to_nid(page); + target_nid = numa_migrate_prep(page, vma, addr, page_nid); pte_unmap_unlock(ptep, ptl); if (target_nid == -1) { - /* - * Account for the fault against the current node if it not - * being replaced regardless of where the page is located. - */ - current_nid = numa_node_id(); put_page(page); goto out; } @@ -3583,11 +3578,11 @@ int do_numa_page(struct mm_struct *mm, struct vm_area_struct *vma, /* Migrate to the requested node */ migrated = migrate_misplaced_page(page, target_nid); if (migrated) - current_nid = target_nid; + page_nid = target_nid; out: - if (current_nid != -1) - task_numa_fault(current_nid, 1, migrated); + if (page_nid != -1) + task_numa_fault(page_nid, 1, migrated); return 0; } @@ -3602,7 +3597,6 @@ static int do_pmd_numa_page(struct mm_struct *mm, struct vm_area_struct *vma, unsigned long offset; spinlock_t *ptl; bool numa = false; - int local_nid = numa_node_id(); spin_lock(&mm->page_table_lock); pmd = *pmdp; @@ -3625,9 +3619,10 @@ static int do_pmd_numa_page(struct mm_struct *mm, struct vm_area_struct *vma, for (addr = _addr + offset; addr < _addr + PMD_SIZE; pte++, addr += PAGE_SIZE) { pte_t pteval = *pte; struct page *page; - int curr_nid = local_nid; + int page_nid = -1; int target_nid; - bool migrated; + bool migrated = false; + if (!pte_present(pteval)) continue; if (!pte_numa(pteval)) @@ -3649,25 +3644,19 @@ static int do_pmd_numa_page(struct mm_struct *mm, struct vm_area_struct *vma, if (unlikely(page_mapcount(page) != 1)) continue; - /* - * Note that the NUMA fault is later accounted to either - * the node that is currently running or where the page is - * migrated to. - */ - curr_nid = local_nid; - target_nid = numa_migrate_prep(page, vma, addr, - page_to_nid(page)); - if (target_nid == -1) { + page_nid = page_to_nid(page); + target_nid = numa_migrate_prep(page, vma, addr, page_nid); + pte_unmap_unlock(pte, ptl); + if (target_nid != -1) { + migrated = migrate_misplaced_page(page, target_nid); + if (migrated) + page_nid = target_nid; + } else { put_page(page); - continue; } - /* Migrate to the requested node */ - pte_unmap_unlock(pte, ptl); - migrated = migrate_misplaced_page(page, target_nid); - if (migrated) - curr_nid = target_nid; - task_numa_fault(curr_nid, 1, migrated); + if (page_nid != -1) + task_numa_fault(page_nid, 1, migrated); pte = pte_offset_map_lock(mm, pmdp, addr, &ptl); } diff --git a/mm/migrate.c b/mm/migrate.c index 7a7325e..c046927 100644 --- a/mm/migrate.c +++ b/mm/migrate.c @@ -1715,12 +1715,12 @@ int migrate_misplaced_transhuge_page(struct mm_struct *mm, unlock_page(new_page); put_page(new_page); /* Free it */ - unlock_page(page); + /* Retake the callers reference and putback on LRU */ + get_page(page); putback_lru_page(page); - - count_vm_events(PGMIGRATE_FAIL, HPAGE_PMD_NR); - isolated = 0; - goto out; + mod_zone_page_state(page_zone(page), + NR_ISOLATED_ANON + page_lru, -HPAGE_PMD_NR); + goto out_fail; } /* @@ -1737,9 +1737,9 @@ int migrate_misplaced_transhuge_page(struct mm_struct *mm, entry = maybe_pmd_mkwrite(pmd_mkdirty(entry), vma); entry = pmd_mkhuge(entry); - page_add_new_anon_rmap(new_page, vma, haddr); - + pmdp_clear_flush(vma, haddr, pmd); set_pmd_at(mm, haddr, pmd, entry); + page_add_new_anon_rmap(new_page, vma, haddr); update_mmu_cache_pmd(vma, address, &entry); page_remove_rmap(page); /* @@ -1758,7 +1758,6 @@ int migrate_misplaced_transhuge_page(struct mm_struct *mm, count_vm_events(PGMIGRATE_SUCCESS, HPAGE_PMD_NR); count_vm_numa_events(NUMA_PAGE_MIGRATE, HPAGE_PMD_NR); -out: mod_zone_page_state(page_zone(page), NR_ISOLATED_ANON + page_lru, -HPAGE_PMD_NR); @@ -1767,6 +1766,10 @@ out: out_fail: count_vm_events(PGMIGRATE_FAIL, HPAGE_PMD_NR); out_dropref: + entry = pmd_mknonnuma(entry); + set_pmd_at(mm, haddr, pmd, entry); + update_mmu_cache_pmd(vma, address, &entry); + unlock_page(page); put_page(page); return 0; diff --git a/mm/mprotect.c b/mm/mprotect.c index a3af058..412ba2b 100644 --- a/mm/mprotect.c +++ b/mm/mprotect.c @@ -148,7 +148,7 @@ static inline unsigned long change_pmd_range(struct vm_area_struct *vma, split_huge_page_pmd(vma, addr, pmd); else if (change_huge_pmd(vma, pmd, addr, newprot, prot_numa)) { - pages += HPAGE_PMD_NR; + pages++; continue; } /* fall through */ diff --git a/sound/core/pcm.c b/sound/core/pcm.c index 17f45e8..e1e9e0c 100644 --- a/sound/core/pcm.c +++ b/sound/core/pcm.c @@ -49,6 +49,8 @@ static struct snd_pcm *snd_pcm_get(struct snd_card *card, int device) struct snd_pcm *pcm; list_for_each_entry(pcm, &snd_pcm_devices, list) { + if (pcm->internal) + continue; if (pcm->card == card && pcm->device == device) return pcm; } @@ -60,6 +62,8 @@ static int snd_pcm_next(struct snd_card *card, int device) struct snd_pcm *pcm; list_for_each_entry(pcm, &snd_pcm_devices, list) { + if (pcm->internal) + continue; if (pcm->card == card && pcm->device > device) return pcm->device; else if (pcm->card->number > card->number) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index bf313bea..8ad5543 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -4623,6 +4623,7 @@ static const struct snd_pci_quirk alc662_fixup_tbl[] = { SND_PCI_QUIRK(0x1028, 0x05db, "Dell", ALC668_FIXUP_DELL_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x103c, 0x1632, "HP RP5800", ALC662_FIXUP_HP_RP5800), SND_PCI_QUIRK(0x1043, 0x1477, "ASUS N56VZ", ALC662_FIXUP_ASUS_MODE4), + SND_PCI_QUIRK(0x1043, 0x1bf3, "ASUS N76VZ", ALC662_FIXUP_ASUS_MODE4), SND_PCI_QUIRK(0x1043, 0x8469, "ASUS mobo", ALC662_FIXUP_NO_JACK_DETECT), SND_PCI_QUIRK(0x105b, 0x0cd6, "Foxconn", ALC662_FIXUP_ASUS_MODE2), SND_PCI_QUIRK(0x144d, 0xc051, "Samsung R720", ALC662_FIXUP_IDEAPAD), diff --git a/sound/soc/codecs/wm_hubs.c b/sound/soc/codecs/wm_hubs.c index 8b50e59..01daf65 100644 --- a/sound/soc/codecs/wm_hubs.c +++ b/sound/soc/codecs/wm_hubs.c @@ -530,6 +530,7 @@ static int hp_supply_event(struct snd_soc_dapm_widget *w, hubs->hp_startup_mode); break; } + break; case SND_SOC_DAPM_PRE_PMD: snd_soc_update_bits(codec, WM8993_CHARGE_PUMP_1, diff --git a/sound/soc/soc-dapm.c b/sound/soc/soc-dapm.c index c17c14c..b2949ae 100644 --- a/sound/soc/soc-dapm.c +++ b/sound/soc/soc-dapm.c @@ -1949,7 +1949,7 @@ static ssize_t dapm_widget_power_read_file(struct file *file, w->active ? "active" : "inactive"); list_for_each_entry(p, &w->sources, list_sink) { - if (p->connected && !p->connected(w, p->sink)) + if (p->connected && !p->connected(w, p->source)) continue; if (p->connect) @@ -3495,6 +3495,7 @@ int snd_soc_dapm_new_dai_widgets(struct snd_soc_dapm_context *dapm, if (!w) { dev_err(dapm->dev, "ASoC: Failed to create %s widget\n", dai->driver->playback.stream_name); + return -ENOMEM; } w->priv = dai; @@ -3513,6 +3514,7 @@ int snd_soc_dapm_new_dai_widgets(struct snd_soc_dapm_context *dapm, if (!w) { dev_err(dapm->dev, "ASoC: Failed to create %s widget\n", dai->driver->capture.stream_name); + return -ENOMEM; } w->priv = dai; |
