diff options
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-rk3x.txt | 42 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt | 41 | ||||
| -rw-r--r-- | drivers/i2c/busses/Kconfig | 23 | ||||
| -rw-r--r-- | drivers/i2c/busses/Makefile | 2 | ||||
| -rw-r--r-- | drivers/i2c/busses/i2c-rk3x.c | 763 | ||||
| -rw-r--r-- | drivers/i2c/busses/i2c-sun6i-p2wi.c | 345 |
6 files changed, 1216 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt new file mode 100644 index 0000000..dde6c22 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -0,0 +1,42 @@ +* Rockchip RK3xxx I2C controller + +This driver interfaces with the native I2C controller present in Rockchip +RK3xxx SoCs. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or + "rockchip,rk3288-i2c". + - interrupts : interrupt number + - clocks : parent clock + +Required on RK3066, RK3188 : + + - rockchip,grf : the phandle of the syscon node for the general register + file (GRF) + - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF) + is also required. + +Optional properties : + + - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used. + +Example: + +aliases { + i2c0 = &i2c0; +} + +i2c0: i2c@2002d000 { + compatible = "rockchip,rk3188-i2c"; + reg = <0x2002d000 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + rockchip,grf = <&grf>; + + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt new file mode 100644 index 0000000..6b76548 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt @@ -0,0 +1,41 @@ + +* Allwinner P2WI (Push/Pull 2 Wire Interface) controller + +Required properties : + + - reg : Offset and length of the register set for the device. + - compatible : Should one of the following: + - "allwinner,sun6i-a31-p2wi" + - interrupts : The interrupt line connected to the P2WI peripheral. + - clocks : The gate clk connected to the P2WI peripheral. + - resets : The reset line connected to the P2WI peripheral. + +Optional properties : + + - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the +default frequency is 100kHz + +A P2WI may contain one child node encoding a P2WI slave device. + +Slave device properties: + Required properties: + - reg : the I2C slave address used during the initialization + process to switch from I2C to P2WI mode + +Example: + + p2wi@01f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <6000000>; + resets = <&apb0_rst 3>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + + /* ... */ + }; + }; diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 620d100..9f7d585 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -676,6 +676,16 @@ config I2C_RIIC This driver can also be built as a module. If so, the module will be called i2c-riic. +config I2C_RK3X + tristate "Rockchip RK3xxx I2C adapter" + depends on OF + help + Say Y here to include support for the I2C adapter in Rockchip RK3xxx + SoCs. + + This driver can also be built as a module. If so, the module will + be called i2c-rk3x. + config HAVE_S3C2410_I2C bool help @@ -764,6 +774,19 @@ config I2C_STU300 This driver can also be built as a module. If so, the module will be called i2c-stu300. +config I2C_SUN6I_P2WI + tristate "Allwinner sun6i internal P2WI controller" + depends on RESET_CONTROLLER + depends on MACH_SUN6I || COMPILE_TEST + help + If you say yes to this option, support will be included for the + P2WI (Push/Pull 2 Wire Interface) controller embedded in some sunxi + SOCs. + The P2WI looks like an SMBus controller (which supports only byte + accesses), except that it only supports one slave device. + This interface is used to connect to specific PMIC devices (like the + AXP221). + config I2C_TEGRA tristate "NVIDIA Tegra internal I2C controller" depends on ARCH_TEGRA diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index 298692c..dd9a7f8 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -66,6 +66,7 @@ obj-$(CONFIG_I2C_PXA) += i2c-pxa.o obj-$(CONFIG_I2C_PXA_PCI) += i2c-pxa-pci.o obj-$(CONFIG_I2C_QUP) += i2c-qup.o obj-$(CONFIG_I2C_RIIC) += i2c-riic.o +obj-$(CONFIG_I2C_RK3X) += i2c-rk3x.o obj-$(CONFIG_I2C_S3C2410) += i2c-s3c2410.o obj-$(CONFIG_I2C_S6000) += i2c-s6000.o obj-$(CONFIG_I2C_SH7760) += i2c-sh7760.o @@ -74,6 +75,7 @@ obj-$(CONFIG_I2C_SIMTEC) += i2c-simtec.o obj-$(CONFIG_I2C_SIRF) += i2c-sirf.o obj-$(CONFIG_I2C_ST) += i2c-st.o obj-$(CONFIG_I2C_STU300) += i2c-stu300.o +obj-$(CONFIG_I2C_SUN6I_P2WI) += i2c-sun6i-p2wi.o obj-$(CONFIG_I2C_TEGRA) += i2c-tegra.o obj-$(CONFIG_I2C_VERSATILE) += i2c-versatile.o obj-$(CONFIG_I2C_WMT) += i2c-wmt.o diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c new file mode 100644 index 0000000..a979150 --- /dev/null +++ b/drivers/i2c/busses/i2c-rk3x.c @@ -0,0 +1,763 @@ +/* + * Driver for I2C adapter in Rockchip RK3xxx SoC + * + * Max Schwarz <max.schwarz@online.de> + * based on the patches by Rockchip Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/spinlock.h> +#include <linux/clk.h> +#include <linux/wait.h> +#include <linux/mfd/syscon.h> +#include <linux/regmap.h> + + +/* Register Map */ +#define REG_CON 0x00 /* control register */ +#define REG_CLKDIV 0x04 /* clock divisor register */ +#define REG_MRXADDR 0x08 /* slave address for REGISTER_TX */ +#define REG_MRXRADDR 0x0c /* slave register address for REGISTER_TX */ +#define REG_MTXCNT 0x10 /* number of bytes to be transmitted */ +#define REG_MRXCNT 0x14 /* number of bytes to be received */ +#define REG_IEN 0x18 /* interrupt enable */ +#define REG_IPD 0x1c /* interrupt pending */ +#define REG_FCNT 0x20 /* finished count */ + +/* Data buffer offsets */ +#define TXBUFFER_BASE 0x100 +#define RXBUFFER_BASE 0x200 + +/* REG_CON bits */ +#define REG_CON_EN BIT(0) +enum { + REG_CON_MOD_TX = 0, /* transmit data */ + REG_CON_MOD_REGISTER_TX, /* select register and restart */ + REG_CON_MOD_RX, /* receive data */ + REG_CON_MOD_REGISTER_RX, /* broken: transmits read addr AND writes + * register addr */ +}; +#define REG_CON_MOD(mod) ((mod) << 1) +#define REG_CON_MOD_MASK (BIT(1) | BIT(2)) +#define REG_CON_START BIT(3) +#define REG_CON_STOP BIT(4) +#define REG_CON_LASTACK BIT(5) /* 1: send NACK after last received byte */ +#define REG_CON_ACTACK BIT(6) /* 1: stop if NACK is received */ + +/* REG_MRXADDR bits */ +#define REG_MRXADDR_VALID(x) BIT(24 + (x)) /* [x*8+7:x*8] of MRX[R]ADDR valid */ + +/* REG_IEN/REG_IPD bits */ +#define REG_INT_BTF BIT(0) /* a byte was transmitted */ +#define REG_INT_BRF BIT(1) /* a byte was received */ +#define REG_INT_MBTF BIT(2) /* master data transmit finished */ +#define REG_INT_MBRF BIT(3) /* master data receive finished */ +#define REG_INT_START BIT(4) /* START condition generated */ +#define REG_INT_STOP BIT(5) /* STOP condition generated */ +#define REG_INT_NAKRCV BIT(6) /* NACK received */ +#define REG_INT_ALL 0x7f + +/* Constants */ +#define WAIT_TIMEOUT 200 /* ms */ +#define DEFAULT_SCL_RATE (100 * 1000) /* Hz */ + +enum rk3x_i2c_state { + STATE_IDLE, + STATE_START, + STATE_READ, + STATE_WRITE, + STATE_STOP +}; + +/** + * @grf_offset: offset inside the grf regmap for setting the i2c type + */ +struct rk3x_i2c_soc_data { + int grf_offset; +}; + +struct rk3x_i2c { + struct i2c_adapter adap; + struct device *dev; + struct rk3x_i2c_soc_data *soc_data; + + /* Hardware resources */ + void __iomem *regs; + struct clk *clk; + + /* Settings */ + unsigned int scl_frequency; + + /* Synchronization & notification */ + spinlock_t lock; + wait_queue_head_t wait; + bool busy; + + /* Current message */ + struct i2c_msg *msg; + u8 addr; + unsigned int mode; + bool is_last_msg; + + /* I2C state machine */ + enum rk3x_i2c_state state; + unsigned int processed; /* sent/received bytes */ + int error; +}; + +static inline void i2c_writel(struct rk3x_i2c *i2c, u32 value, + unsigned int offset) +{ + writel(value, i2c->regs + offset); +} + +static inline u32 i2c_readl(struct rk3x_i2c *i2c, unsigned int offset) +{ + return readl(i2c->regs + offset); +} + +/* Reset all interrupt pending bits */ +static inline void rk3x_i2c_clean_ipd(struct rk3x_i2c *i2c) +{ + i2c_writel(i2c, REG_INT_ALL, REG_IPD); +} + +/** + * Generate a START condition, which triggers a REG_INT_START interrupt. + */ +static void rk3x_i2c_start(struct rk3x_i2c *i2c) +{ + u32 val; + + rk3x_i2c_clean_ipd(i2c); + i2c_writel(i2c, REG_INT_START, REG_IEN); + + /* enable adapter with correct mode, send START condition */ + val = REG_CON_EN | REG_CON_MOD(i2c->mode) | REG_CON_START; + + /* if we want to react to NACK, set ACTACK bit */ + if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) + val |= REG_CON_ACTACK; + + i2c_writel(i2c, val, REG_CON); +} + +/** + * Generate a STOP condition, which triggers a REG_INT_STOP interrupt. + * + * @error: Error code to return in rk3x_i2c_xfer + */ +static void rk3x_i2c_stop(struct rk3x_i2c *i2c, int error) +{ + unsigned int ctrl; + + i2c->processed = 0; + i2c->msg = NULL; + i2c->error = error; + + if (i2c->is_last_msg) { + /* Enable stop interrupt */ + i2c_writel(i2c, REG_INT_STOP, REG_IEN); + + i2c->state = STATE_STOP; + + ctrl = i2c_readl(i2c, REG_CON); + ctrl |= REG_CON_STOP; + i2c_writel(i2c, ctrl, REG_CON); + } else { + /* Signal rk3x_i2c_xfer to start the next message. */ + i2c->busy = false; + i2c->state = STATE_IDLE; + + /* + * The HW is actually not capable of REPEATED START. But we can + * get the intended effect by resetting its internal state + * and issuing an ordinary START. + */ + i2c_writel(i2c, 0, REG_CON); + + /* signal that we are finished with the current msg */ + wake_up(&i2c->wait); + } +} + +/** + * Setup a read according to i2c->msg + */ +static void rk3x_i2c_prepare_read(struct rk3x_i2c *i2c) +{ + unsigned int len = i2c->msg->len - i2c->processed; + u32 con; + + con = i2c_readl(i2c, REG_CON); + + /* + * The hw can read up to 32 bytes at a time. If we need more than one + * chunk, send an ACK after the last byte of the current chunk. + */ + if (unlikely(len > 32)) { + len = 32; + con &= ~REG_CON_LASTACK; + } else { + con |= REG_CON_LASTACK; + } + + /* make sure we are in plain RX mode if we read a second chunk */ + if (i2c->processed != 0) { + con &= ~REG_CON_MOD_MASK; + con |= REG_CON_MOD(REG_CON_MOD_RX); + } + + i2c_writel(i2c, con, REG_CON); + i2c_writel(i2c, len, REG_MRXCNT); +} + +/** + * Fill the transmit buffer with data from i2c->msg + */ +static void rk3x_i2c_fill_transmit_buf(struct rk3x_i2c *i2c) +{ + unsigned int i, j; + u32 cnt = 0; + u32 val; + u8 byte; + + for (i = 0; i < 8; ++i) { + val = 0; + for (j = 0; j < 4; ++j) { + if (i2c->processed == i2c->msg->len) + break; + + if (i2c->processed == 0 && cnt == 0) + byte = (i2c->addr & 0x7f) << 1; + else + byte = i2c->msg->buf[i2c->processed++]; + + val |= byte << (j * 8); + cnt++; + } + + i2c_writel(i2c, val, TXBUFFER_BASE + 4 * i); + + if (i2c->processed == i2c->msg->len) + break; + } + + i2c_writel(i2c, cnt, REG_MTXCNT); +} + + +/* IRQ handlers for individual states */ + +static void rk3x_i2c_handle_start(struct rk3x_i2c *i2c, unsigned int ipd) +{ + if (!(ipd & REG_INT_START)) { + rk3x_i2c_stop(i2c, -EIO); + dev_warn(i2c->dev, "unexpected irq in START: 0x%x\n", ipd); + rk3x_i2c_clean_ipd(i2c); + return; + } + + /* ack interrupt */ + i2c_writel(i2c, REG_INT_START, REG_IPD); + + /* disable start bit */ + i2c_writel(i2c, i2c_readl(i2c, REG_CON) & ~REG_CON_START, REG_CON); + + /* enable appropriate interrupts and transition */ + if (i2c->mode == REG_CON_MOD_TX) { + i2c_writel(i2c, REG_INT_MBTF | REG_INT_NAKRCV, REG_IEN); + i2c->state = STATE_WRITE; + rk3x_i2c_fill_transmit_buf(i2c); + } else { + /* in any other case, we are going to be reading. */ + i2c_writel(i2c, REG_INT_MBRF | REG_INT_NAKRCV, REG_IEN); + i2c->state = STATE_READ; + rk3x_i2c_prepare_read(i2c); + } +} + +static void rk3x_i2c_handle_write(struct rk3x_i2c *i2c, unsigned int ipd) +{ + if (!(ipd & REG_INT_MBTF)) { + rk3x_i2c_stop(i2c, -EIO); + dev_err(i2c->dev, "unexpected irq in WRITE: 0x%x\n", ipd); + rk3x_i2c_clean_ipd(i2c); + return; + } + + /* ack interrupt */ + i2c_writel(i2c, REG_INT_MBTF, REG_IPD); + + /* are we finished? */ + if (i2c->processed == i2c->msg->len) + rk3x_i2c_stop(i2c, i2c->error); + else + rk3x_i2c_fill_transmit_buf(i2c); +} + +static void rk3x_i2c_handle_read(struct rk3x_i2c *i2c, unsigned int ipd) +{ + unsigned int i; + unsigned int len = i2c->msg->len - i2c->processed; + u32 uninitialized_var(val); + u8 byte; + + /* we only care for MBRF here. */ + if (!(ipd & REG_INT_MBRF)) + return; + + /* ack interrupt */ + i2c_writel(i2c, REG_INT_MBRF, REG_IPD); + + /* read the data from receive buffer */ + for (i = 0; i < len; ++i) { + if (i % 4 == 0) + val = i2c_readl(i2c, RXBUFFER_BASE + (i / 4) * 4); + + byte = (val >> ((i % 4) * 8)) & 0xff; + i2c->msg->buf[i2c->processed++] = byte; + } + + /* are we finished? */ + if (i2c->processed == i2c->msg->len) + rk3x_i2c_stop(i2c, i2c->error); + else + rk3x_i2c_prepare_read(i2c); +} + +static void rk3x_i2c_handle_stop(struct rk3x_i2c *i2c, unsigned int ipd) +{ + unsigned int con; + + if (!(ipd & REG_INT_STOP)) { + rk3x_i2c_stop(i2c, -EIO); + dev_err(i2c->dev, "unexpected irq in STOP: 0x%x\n", ipd); + rk3x_i2c_clean_ipd(i2c); + return; + } + + /* ack interrupt */ + i2c_writel(i2c, REG_INT_STOP, REG_IPD); + + /* disable STOP bit */ + con = i2c_readl(i2c, REG_CON); + con &= ~REG_CON_STOP; + i2c_writel(i2c, con, REG_CON); + + i2c->busy = false; + i2c->state = STATE_IDLE; + + /* signal rk3x_i2c_xfer that we are finished */ + wake_up(&i2c->wait); +} + +static irqreturn_t rk3x_i2c_irq(int irqno, void *dev_id) +{ + struct rk3x_i2c *i2c = dev_id; + unsigned int ipd; + + spin_lock(&i2c->lock); + + ipd = i2c_readl(i2c, REG_IPD); + if (i2c->state == STATE_IDLE) { + dev_warn(i2c->dev, "irq in STATE_IDLE, ipd = 0x%x\n", ipd); + rk3x_i2c_clean_ipd(i2c); + goto out; + } + + dev_dbg(i2c->dev, "IRQ: state %d, ipd: %x\n", i2c->state, ipd); + + /* Clean interrupt bits we don't care about */ + ipd &= ~(REG_INT_BRF | REG_INT_BTF); + + if (ipd & REG_INT_NAKRCV) { + /* + * We got a NACK in the last operation. Depending on whether + * IGNORE_NAK is set, we have to stop the operation and report + * an error. + */ + i2c_writel(i2c, REG_INT_NAKRCV, REG_IPD); + + ipd &= ~REG_INT_NAKRCV; + + if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) + rk3x_i2c_stop(i2c, -ENXIO); + } + + /* is there anything left to handle? */ + if (unlikely(ipd == 0)) + goto out; + + switch (i2c->state) { + case STATE_START: + rk3x_i2c_handle_start(i2c, ipd); + break; + case STATE_WRITE: + rk3x_i2c_handle_write(i2c, ipd); + break; + case STATE_READ: + rk3x_i2c_handle_read(i2c, ipd); + break; + case STATE_STOP: + rk3x_i2c_handle_stop(i2c, ipd); + break; + case STATE_IDLE: + break; + } + +out: + spin_unlock(&i2c->lock); + return IRQ_HANDLED; +} + +static void rk3x_i2c_set_scl_rate(struct rk3x_i2c *i2c, unsigned long scl_rate) +{ + unsigned long i2c_rate = clk_get_rate(i2c->clk); + unsigned int div; + + /* SCL rate = (clk rate) / (8 * DIV) */ + div = DIV_ROUND_UP(i2c_rate, scl_rate * 8); + + /* The lower and upper half of the CLKDIV reg describe the length of + * SCL low & high periods. */ + div = DIV_ROUND_UP(div, 2); + + i2c_writel(i2c, (div << 16) | (div & 0xffff), REG_CLKDIV); +} + +/** + * Setup I2C registers for an I2C operation specified by msgs, num. + * + * Must be called with i2c->lock held. + * + * @msgs: I2C msgs to process + * @num: Number of msgs + * + * returns: Number of I2C msgs processed or negative in case of error + */ +static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int num) +{ + u32 addr = (msgs[0].addr & 0x7f) << 1; + int ret = 0; + + /* + * The I2C adapter can issue a small (len < 4) write packet before + * reading. This speeds up SMBus-style register reads. + * The MRXADDR/MRXRADDR hold the slave address and the slave register + * address in this case. + */ + + if (num >= 2 && msgs[0].len < 4 && + !(msgs[0].flags & I2C_M_RD) && (msgs[1].flags & I2C_M_RD)) { + u32 reg_addr = 0; + int i; + + dev_dbg(i2c->dev, "Combined write/read from addr 0x%x\n", + addr >> 1); + + /* Fill MRXRADDR with the register address(es) */ + for (i = 0; i < msgs[0].len; ++i) { + reg_addr |= msgs[0].buf[i] << (i * 8); + reg_addr |= REG_MRXADDR_VALID(i); + } + + /* msgs[0] is handled by hw. */ + i2c->msg = &msgs[1]; + + i2c->mode = REG_CON_MOD_REGISTER_TX; + + i2c_writel(i2c, addr | REG_MRXADDR_VALID(0), REG_MRXADDR); + i2c_writel(i2c, reg_addr, REG_MRXRADDR); + + ret = 2; + } else { + /* + * We'll have to do it the boring way and process the msgs + * one-by-one. + */ + + if (msgs[0].flags & I2C_M_RD) { + addr |= 1; /* set read bit */ + + /* + * We have to transmit the slave addr first. Use + * MOD_REGISTER_TX for that purpose. + */ + i2c->mode = REG_CON_MOD_REGISTER_TX; + i2c_writel(i2c, addr | REG_MRXADDR_VALID(0), + REG_MRXADDR); + i2c_writel(i2c, 0, REG_MRXRADDR); + } else { + i2c->mode = REG_CON_MOD_TX; + } + + i2c->msg = &msgs[0]; + + ret = 1; + } + + i2c->addr = msgs[0].addr; + i2c->busy = true; + i2c->state = STATE_START; + i2c->processed = 0; + i2c->error = 0; + + rk3x_i2c_clean_ipd(i2c); + + return ret; +} + +static int rk3x_i2c_xfer(struct i2c_adapter *adap, + struct i2c_msg *msgs, int num) +{ + struct rk3x_i2c *i2c = (struct rk3x_i2c *)adap->algo_data; + unsigned long timeout, flags; + int ret = 0; + int i; + + spin_lock_irqsave(&i2c->lock, flags); + + clk_enable(i2c->clk); + + /* The clock rate might have changed, so setup the divider again */ + rk3x_i2c_set_scl_rate(i2c, i2c->scl_frequency); + + i2c->is_last_msg = false; + + /* + * Process msgs. We can handle more than one message at once (see + * rk3x_i2c_setup()). + */ + for (i = 0; i < num; i += ret) { + ret = rk3x_i2c_setup(i2c, msgs + i, num - i); + + if (ret < 0) { + dev_err(i2c->dev, "rk3x_i2c_setup() failed\n"); + break; + } + + if (i + ret >= num) + i2c->is_last_msg = true; + + spin_unlock_irqrestore(&i2c->lock, flags); + + rk3x_i2c_start(i2c); + + timeout = wait_event_timeout(i2c->wait, !i2c->busy, + msecs_to_jiffies(WAIT_TIMEOUT)); + + spin_lock_irqsave(&i2c->lock, flags); + + if (timeout == 0) { + dev_err(i2c->dev, "timeout, ipd: 0x%02x, state: %d\n", + i2c_readl(i2c, REG_IPD), i2c->state); + + /* Force a STOP condition without interrupt */ + i2c_writel(i2c, 0, REG_IEN); + i2c_writel(i2c, REG_CON_EN | REG_CON_STOP, REG_CON); + + i2c->state = STATE_IDLE; + + ret = -ETIMEDOUT; + break; + } + + if (i2c->error) { + ret = i2c->error; + break; + } + } + + clk_disable(i2c->clk); + spin_unlock_irqrestore(&i2c->lock, flags); + + return ret; +} + +static u32 rk3x_i2c_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING; +} + +static const struct i2c_algorithm rk3x_i2c_algorithm = { + .master_xfer = rk3x_i2c_xfer, + .functionality = rk3x_i2c_func, +}; + +static struct rk3x_i2c_soc_data soc_data[3] = { + { .grf_offset = 0x154 }, /* rk3066 */ + { .grf_offset = 0x0a4 }, /* rk3188 */ + { .grf_offset = -1 }, /* no I2C switching needed */ +}; + +static const struct of_device_id rk3x_i2c_match[] = { + { .compatible = "rockchip,rk3066-i2c", .data = (void *)&soc_data[0] }, + { .compatible = "rockchip,rk3188-i2c", .data = (void *)&soc_data[1] }, + { .compatible = "rockchip,rk3288-i2c", .data = (void *)&soc_data[2] }, + {}, +}; + +static int rk3x_i2c_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + const struct of_device_id *match; + struct rk3x_i2c *i2c; + struct resource *mem; + int ret = 0; + int bus_nr; + u32 value; + int irq; + + i2c = devm_kzalloc(&pdev->dev, sizeof(struct rk3x_i2c), GFP_KERNEL); + if (!i2c) + return -ENOMEM; + + match = of_match_node(rk3x_i2c_match, np); + i2c->soc_data = (struct rk3x_i2c_soc_data *)match->data; + + if (of_property_read_u32(pdev->dev.of_node, "clock-frequency", + &i2c->scl_frequency)) { + dev_info(&pdev->dev, "using default SCL frequency: %d\n", + DEFAULT_SCL_RATE); + i2c->scl_frequency = DEFAULT_SCL_RATE; + } + + if (i2c->scl_frequency == 0 || i2c->scl_frequency > 400 * 1000) { + dev_warn(&pdev->dev, "invalid SCL frequency specified.\n"); + dev_warn(&pdev->dev, "using default SCL frequency: %d\n", + DEFAULT_SCL_RATE); + i2c->scl_frequency = DEFAULT_SCL_RATE; + } + + strlcpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name)); + i2c->adap.owner = THIS_MODULE; + i2c->adap.algo = &rk3x_i2c_algorithm; + i2c->adap.retries = 3; + i2c->adap.dev.of_node = np; + i2c->adap.algo_data = i2c; + i2c->adap.dev.parent = &pdev->dev; + + i2c->dev = &pdev->dev; + + spin_lock_init(&i2c->lock); + init_waitqueue_head(&i2c->wait); + + i2c->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(i2c->clk)) { + dev_err(&pdev->dev, "cannot get clock\n"); + return PTR_ERR(i2c->clk); + } + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + i2c->regs = devm_ioremap_resource(&pdev->dev, mem); + if (IS_ERR(i2c->regs)) + return PTR_ERR(i2c->regs); + + /* Try to set the I2C adapter number from dt */ + bus_nr = of_alias_get_id(np, "i2c"); + + /* + * Switch to new interface if the SoC also offers the old one. + * The control bit is located in the GRF register space. + */ + if (i2c->soc_data->grf_offset >= 0) { + struct regmap *grf; + + grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); + if (IS_ERR(grf)) { + dev_err(&pdev->dev, + "rk3x-i2c needs 'rockchip,grf' property\n"); + return PTR_ERR(grf); + } + + if (bus_nr < 0) { + dev_err(&pdev->dev, "rk3x-i2c needs i2cX alias"); + return -EINVAL; + } + + /* 27+i: write mask, 11+i: value */ + value = BIT(27 + bus_nr) | BIT(11 + bus_nr); + + ret = regmap_write(grf, i2c->soc_data->grf_offset, value); + if (ret != 0) { + dev_err(i2c->dev, "Could not write to GRF: %d\n", ret); + return ret; + } + } + + /* IRQ setup */ + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "cannot find rk3x IRQ\n"); + return irq; + } + + ret = devm_request_irq(&pdev->dev, irq, rk3x_i2c_irq, + 0, dev_name(&pdev->dev), i2c); + if (ret < 0) { + dev_err(&pdev->dev, "cannot request IRQ\n"); + return ret; + } + + platform_set_drvdata(pdev, i2c); + + ret = clk_prepare(i2c->clk); + if (ret < 0) { + dev_err(&pdev->dev, "Could not prepare clock\n"); + return ret; + } + + ret = i2c_add_adapter(&i2c->adap); + if (ret < 0) { + dev_err(&pdev->dev, "Could not register adapter\n"); + goto err_clk; + } + + dev_info(&pdev->dev, "Initialized RK3xxx I2C bus at %p\n", i2c->regs); + + return 0; + +err_clk: + clk_unprepare(i2c->clk); + return ret; +} + +static int rk3x_i2c_remove(struct platform_device *pdev) +{ + struct rk3x_i2c *i2c = platform_get_drvdata(pdev); + + i2c_del_adapter(&i2c->adap); + clk_unprepare(i2c->clk); + + return 0; +} + +static struct platform_driver rk3x_i2c_driver = { + .probe = rk3x_i2c_probe, + .remove = rk3x_i2c_remove, + .driver = { + .owner = THIS_MODULE, + .name = "rk3x-i2c", + .of_match_table = rk3x_i2c_match, + }, +}; + +module_platform_driver(rk3x_i2c_driver); + +MODULE_DESCRIPTION("Rockchip RK3xxx I2C Bus driver"); +MODULE_AUTHOR("Max Schwarz <max.schwarz@online.de>"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/i2c/busses/i2c-sun6i-p2wi.c b/drivers/i2c/busses/i2c-sun6i-p2wi.c new file mode 100644 index 0000000..09de4fd --- /dev/null +++ b/drivers/i2c/busses/i2c-sun6i-p2wi.c @@ -0,0 +1,345 @@ +/* + * P2WI (Push-Pull Two Wire Interface) bus driver. + * + * Author: Boris BREZILLON <boris.brezillon@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + * + * The P2WI controller looks like an SMBus controller which only supports byte + * data transfers. But, it differs from standard SMBus protocol on several + * aspects: + * - it supports only one slave device, and thus drop the address field + * - it adds a parity bit every 8bits of data + * - only one read access is required to read a byte (instead of a write + * followed by a read access in standard SMBus protocol) + * - there's no Ack bit after each byte transfer + * + * This means this bus cannot be used to interface with standard SMBus + * devices (the only known device to support this interface is the AXP221 + * PMIC). + * + */ +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/io.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/reset.h> + + +/* P2WI registers */ +#define P2WI_CTRL 0x0 +#define P2WI_CCR 0x4 +#define P2WI_INTE 0x8 +#define P2WI_INTS 0xc +#define P2WI_DADDR0 0x10 +#define P2WI_DADDR1 0x14 +#define P2WI_DLEN 0x18 +#define P2WI_DATA0 0x1c +#define P2WI_DATA1 0x20 +#define P2WI_LCR 0x24 +#define P2WI_PMCR 0x28 + +/* CTRL fields */ +#define P2WI_CTRL_START_TRANS BIT(7) +#define P2WI_CTRL_ABORT_TRANS BIT(6) +#define P2WI_CTRL_GLOBAL_INT_ENB BIT(1) +#define P2WI_CTRL_SOFT_RST BIT(0) + +/* CLK CTRL fields */ +#define P2WI_CCR_SDA_OUT_DELAY(v) (((v) & 0x7) << 8) +#define P2WI_CCR_MAX_CLK_DIV 0xff +#define P2WI_CCR_CLK_DIV(v) ((v) & P2WI_CCR_MAX_CLK_DIV) + +/* STATUS fields */ +#define P2WI_INTS_TRANS_ERR_ID(v) (((v) >> 8) & 0xff) +#define P2WI_INTS_LOAD_BSY BIT(2) +#define P2WI_INTS_TRANS_ERR BIT(1) +#define P2WI_INTS_TRANS_OVER BIT(0) + +/* DATA LENGTH fields*/ +#define P2WI_DLEN_READ BIT(4) +#define P2WI_DLEN_DATA_LENGTH(v) ((v - 1) & 0x7) + +/* LINE CTRL fields*/ +#define P2WI_LCR_SCL_STATE BIT(5) +#define P2WI_LCR_SDA_STATE BIT(4) +#define P2WI_LCR_SCL_CTL BIT(3) +#define P2WI_LCR_SCL_CTL_EN BIT(2) +#define P2WI_LCR_SDA_CTL BIT(1) +#define P2WI_LCR_SDA_CTL_EN BIT(0) + +/* PMU MODE CTRL fields */ +#define P2WI_PMCR_PMU_INIT_SEND BIT(31) +#define P2WI_PMCR_PMU_INIT_DATA(v) (((v) & 0xff) << 16) +#define P2WI_PMCR_PMU_MODE_REG(v) (((v) & 0xff) << 8) +#define P2WI_PMCR_PMU_DEV_ADDR(v) ((v) & 0xff) + +#define P2WI_MAX_FREQ 6000000 + +struct p2wi { + struct i2c_adapter adapter; + struct completion complete; + unsigned int status; + void __iomem *regs; + struct clk *clk; + struct reset_control *rstc; + int slave_addr; +}; + +static irqreturn_t p2wi_interrupt(int irq, void *dev_id) +{ + struct p2wi *p2wi = dev_id; + unsigned long status; + + status = readl(p2wi->regs + P2WI_INTS); + p2wi->status = status; + + /* Clear interrupts */ + status &= (P2WI_INTS_LOAD_BSY | P2WI_INTS_TRANS_ERR | + P2WI_INTS_TRANS_OVER); + writel(status, p2wi->regs + P2WI_INTS); + + complete(&p2wi->complete); + + return IRQ_HANDLED; +} + +static u32 p2wi_functionality(struct i2c_adapter *adap) +{ + return I2C_FUNC_SMBUS_BYTE_DATA; +} + +static int p2wi_smbus_xfer(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, union i2c_smbus_data *data) +{ + struct p2wi *p2wi = i2c_get_adapdata(adap); + unsigned long dlen = P2WI_DLEN_DATA_LENGTH(1); + + if (p2wi->slave_addr >= 0 && addr != p2wi->slave_addr) { + dev_err(&adap->dev, "invalid P2WI address\n"); + return -EINVAL; + } + + if (!data) + return -EINVAL; + + writel(command, p2wi->regs + P2WI_DADDR0); + + if (read_write == I2C_SMBUS_READ) + dlen |= P2WI_DLEN_READ; + else + writel(data->byte, p2wi->regs + P2WI_DATA0); + + writel(dlen, p2wi->regs + P2WI_DLEN); + + if (readl(p2wi->regs + P2WI_CTRL) & P2WI_CTRL_START_TRANS) { + dev_err(&adap->dev, "P2WI bus busy\n"); + return -EBUSY; + } + + reinit_completion(&p2wi->complete); + + writel(P2WI_INTS_LOAD_BSY | P2WI_INTS_TRANS_ERR | P2WI_INTS_TRANS_OVER, + p2wi->regs + P2WI_INTE); + + writel(P2WI_CTRL_START_TRANS | P2WI_CTRL_GLOBAL_INT_ENB, + p2wi->regs + P2WI_CTRL); + + wait_for_completion(&p2wi->complete); + + if (p2wi->status & P2WI_INTS_LOAD_BSY) { + dev_err(&adap->dev, "P2WI bus busy\n"); + return -EBUSY; + } + + if (p2wi->status & P2WI_INTS_TRANS_ERR) { + dev_err(&adap->dev, "P2WI bus xfer error\n"); + return -ENXIO; + } + + if (read_write == I2C_SMBUS_READ) + data->byte = readl(p2wi->regs + P2WI_DATA0); + + return 0; +} + +static const struct i2c_algorithm p2wi_algo = { + .smbus_xfer = p2wi_smbus_xfer, + .functionality = p2wi_functionality, +}; + +static const struct of_device_id p2wi_of_match_table[] = { + { .compatible = "allwinner,sun6i-a31-p2wi" }, + {} +}; +MODULE_DEVICE_TABLE(of, p2wi_of_match_table); + +static int p2wi_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct device_node *childnp; + unsigned long parent_clk_freq; + u32 clk_freq = 100000; + struct resource *r; + struct p2wi *p2wi; + u32 slave_addr; + int clk_div; + int irq; + int ret; + + of_property_read_u32(np, "clock-frequency", &clk_freq); + if (clk_freq > P2WI_MAX_FREQ) { + dev_err(dev, + "required clock-frequency (%u Hz) is too high (max = 6MHz)", + clk_freq); + return -EINVAL; + } + + if (of_get_child_count(np) > 1) { + dev_err(dev, "P2WI only supports one slave device\n"); + return -EINVAL; + } + + p2wi = devm_kzalloc(dev, sizeof(struct p2wi), GFP_KERNEL); + if (!p2wi) + return -ENOMEM; + + p2wi->slave_addr = -1; + + /* + * Authorize a p2wi node without any children to be able to use an + * i2c-dev from userpace. + * In this case the slave_addr is set to -1 and won't be checked when + * launching a P2WI transfer. + */ + childnp = of_get_next_available_child(np, NULL); + if (childnp) { + ret = of_property_read_u32(childnp, "reg", &slave_addr); + if (ret) { + dev_err(dev, "invalid slave address on node %s\n", + childnp->full_name); + return -EINVAL; + } + + p2wi->slave_addr = slave_addr; + } + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + p2wi->regs = devm_ioremap_resource(dev, r); + if (IS_ERR(p2wi->regs)) + return PTR_ERR(p2wi->regs); + + strlcpy(p2wi->adapter.name, pdev->name, sizeof(p2wi->adapter.name)); + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "failed to retrieve irq: %d\n", irq); + return irq; + } + + p2wi->clk = devm_clk_get(dev, NULL); + if (IS_ERR(p2wi->clk)) { + ret = PTR_ERR(p2wi->clk); + dev_err(dev, "failed to retrieve clk: %d\n", ret); + return ret; + } + + ret = clk_prepare_enable(p2wi->clk); + if (ret) { + dev_err(dev, "failed to enable clk: %d\n", ret); + return ret; + } + + parent_clk_freq = clk_get_rate(p2wi->clk); + + p2wi->rstc = devm_reset_control_get(dev, NULL); + if (IS_ERR(p2wi->rstc)) { + ret = PTR_ERR(p2wi->rstc); + dev_err(dev, "failed to retrieve reset controller: %d\n", ret); + goto err_clk_disable; + } + + ret = reset_control_deassert(p2wi->rstc); + if (ret) { + dev_err(dev, "failed to deassert reset line: %d\n", ret); + goto err_clk_disable; + } + + init_completion(&p2wi->complete); + p2wi->adapter.dev.parent = dev; + p2wi->adapter.algo = &p2wi_algo; + p2wi->adapter.owner = THIS_MODULE; + p2wi->adapter.dev.of_node = pdev->dev.of_node; + platform_set_drvdata(pdev, p2wi); + i2c_set_adapdata(&p2wi->adapter, p2wi); + + ret = devm_request_irq(dev, irq, p2wi_interrupt, 0, pdev->name, p2wi); + if (ret) { + dev_err(dev, "can't register interrupt handler irq%d: %d\n", + irq, ret); + goto err_reset_assert; + } + + writel(P2WI_CTRL_SOFT_RST, p2wi->regs + P2WI_CTRL); + + clk_div = parent_clk_freq / clk_freq; + if (!clk_div) { + dev_warn(dev, + "clock-frequency is too high, setting it to %lu Hz\n", + parent_clk_freq); + clk_div = 1; + } else if (clk_div > P2WI_CCR_MAX_CLK_DIV) { + dev_warn(dev, + "clock-frequency is too low, setting it to %lu Hz\n", + parent_clk_freq / P2WI_CCR_MAX_CLK_DIV); + clk_div = P2WI_CCR_MAX_CLK_DIV; + } + + writel(P2WI_CCR_SDA_OUT_DELAY(1) | P2WI_CCR_CLK_DIV(clk_div), + p2wi->regs + P2WI_CCR); + + ret = i2c_add_adapter(&p2wi->adapter); + if (!ret) + return 0; + +err_reset_assert: + reset_control_assert(p2wi->rstc); + +err_clk_disable: + clk_disable_unprepare(p2wi->clk); + + return ret; +} + +static int p2wi_remove(struct platform_device *dev) +{ + struct p2wi *p2wi = platform_get_drvdata(dev); + + reset_control_assert(p2wi->rstc); + clk_disable_unprepare(p2wi->clk); + i2c_del_adapter(&p2wi->adapter); + + return 0; +} + +static struct platform_driver p2wi_driver = { + .probe = p2wi_probe, + .remove = p2wi_remove, + .driver = { + .owner = THIS_MODULE, + .name = "i2c-sunxi-p2wi", + .of_match_table = p2wi_of_match_table, + }, +}; +module_platform_driver(p2wi_driver); + +MODULE_AUTHOR("Boris BREZILLON <boris.brezillon@free-electrons.com>"); +MODULE_DESCRIPTION("Allwinner P2WI driver"); +MODULE_LICENSE("GPL v2"); |
