summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--drivers/usb/core/message.c4
-rw-r--r--drivers/usb/core/urb.c6
-rw-r--r--drivers/usb/gadget/ether.c2
-rw-r--r--drivers/usb/gadget/inode.c2
-rw-r--r--drivers/usb/gadget/lh7a40x_udc.c2
-rw-r--r--drivers/usb/gadget/serial.c2
-rw-r--r--drivers/usb/host/hc_crisv10.c2
-rw-r--r--drivers/usb/host/sl811-hcd.c4
-rw-r--r--drivers/usb/image/mdc800.c2
-rw-r--r--drivers/usb/input/aiptek.c2
-rw-r--r--drivers/usb/input/mtouchusb.c2
-rw-r--r--drivers/usb/media/ov511.c2
-rw-r--r--drivers/usb/media/pwc/pwc-ctrl.c2
-rw-r--r--drivers/usb/media/pwc/pwc-if.c6
-rw-r--r--drivers/usb/media/pwc/pwc-ioctl.h2
-rw-r--r--drivers/usb/misc/legousbtower.c2
-rw-r--r--drivers/usb/net/zd1201.c8
-rw-r--r--drivers/usb/serial/cypress_m8.c2
-rw-r--r--drivers/usb/serial/ftdi_sio.c4
-rw-r--r--drivers/usb/serial/ftdi_sio.h2
-rw-r--r--drivers/usb/serial/io_usbvend.h2
-rw-r--r--drivers/usb/serial/keyspan_usa90msg.h2
-rw-r--r--drivers/usb/storage/shuttle_usbat.c2
-rw-r--r--drivers/usb/storage/unusual_devs.h2
24 files changed, 34 insertions, 34 deletions
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index e12c5be..f50aaf2 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -431,7 +431,7 @@ nomem:
* (2) error, where io->status is a negative errno value. The number
* of io->bytes transferred before the error is usually less
* than requested, and can be nonzero.
- * (3) cancelation, a type of error with status -ECONNRESET that
+ * (3) cancellation, a type of error with status -ECONNRESET that
* is initiated by usb_sg_cancel().
*
* When this function returns, all memory allocated through usb_sg_init() or
@@ -1282,7 +1282,7 @@ static void release_interface(struct device *dev)
* bus rwsem; usb device driver probe() methods cannot use this routine.
*
* Returns zero on success, or else the status code returned by the
- * underlying call that failed. On succesful completion, each interface
+ * underlying call that failed. On successful completion, each interface
* in the original device configuration has been destroyed, and each one
* in the new configuration has been probed by all relevant usb device
* drivers currently known to the kernel.
diff --git a/drivers/usb/core/urb.c b/drivers/usb/core/urb.c
index 1697215..0faf18d 100644
--- a/drivers/usb/core/urb.c
+++ b/drivers/usb/core/urb.c
@@ -121,7 +121,7 @@ struct urb * usb_get_urb(struct urb *urb)
* describing that request to the USB subsystem. Request completion will
* be indicated later, asynchronously, by calling the completion handler.
* The three types of completion are success, error, and unlink
- * (a software-induced fault, also called "request cancelation").
+ * (a software-induced fault, also called "request cancellation").
*
* URBs may be submitted in interrupt context.
*
@@ -170,7 +170,7 @@ struct urb * usb_get_urb(struct urb *urb)
* As of Linux 2.6, all USB endpoint transfer queues support depths greater
* than one. This was previously a HCD-specific behavior, except for ISO
* transfers. Non-isochronous endpoint queues are inactive during cleanup
- * after faults (transfer errors or cancelation).
+ * after faults (transfer errors or cancellation).
*
* Reserved Bandwidth Transfers:
*
@@ -395,7 +395,7 @@ int usb_submit_urb(struct urb *urb, int mem_flags)
*
* This routine cancels an in-progress request. URBs complete only
* once per submission, and may be canceled only once per submission.
- * Successful cancelation means the requests's completion handler will
+ * Successful cancellation means the requests's completion handler will
* be called with a status code indicating that the request has been
* canceled (rather than any other code) and will quickly be removed
* from host controller data structures.
diff --git a/drivers/usb/gadget/ether.c b/drivers/usb/gadget/ether.c
index 3993156..3f783cb 100644
--- a/drivers/usb/gadget/ether.c
+++ b/drivers/usb/gadget/ether.c
@@ -569,7 +569,7 @@ static const struct usb_cdc_ether_desc ether_desc = {
/* include the status endpoint if we can, even where it's optional.
* use wMaxPacketSize big enough to fit CDC_NOTIFY_SPEED_CHANGE in one
- * packet, to simplify cancelation; and a big transfer interval, to
+ * packet, to simplify cancellation; and a big transfer interval, to
* waste less bandwidth.
*
* some drivers (like Linux 2.4 cdc-ether!) "need" it to exist even
diff --git a/drivers/usb/gadget/inode.c b/drivers/usb/gadget/inode.c
index 2cff67c..1e5e6dd 100644
--- a/drivers/usb/gadget/inode.c
+++ b/drivers/usb/gadget/inode.c
@@ -275,7 +275,7 @@ static const char *CHIP;
*
* After opening, configure non-control endpoints. Then use normal
* stream read() and write() requests; and maybe ioctl() to get more
- * precise FIFO status when recovering from cancelation.
+ * precise FIFO status when recovering from cancellation.
*/
static void epio_complete (struct usb_ep *ep, struct usb_request *req)
diff --git a/drivers/usb/gadget/lh7a40x_udc.c b/drivers/usb/gadget/lh7a40x_udc.c
index 0def9f7..df75ab6 100644
--- a/drivers/usb/gadget/lh7a40x_udc.c
+++ b/drivers/usb/gadget/lh7a40x_udc.c
@@ -705,7 +705,7 @@ void nuke(struct lh7a40x_ep *ep, int status)
done(ep, req, status);
}
- /* Disable IRQ if EP is enabled (has decriptor) */
+ /* Disable IRQ if EP is enabled (has descriptor) */
if (ep->desc)
pio_irq_disable(ep_index(ep));
}
diff --git a/drivers/usb/gadget/serial.c b/drivers/usb/gadget/serial.c
index f1762ed..4d591c7 100644
--- a/drivers/usb/gadget/serial.c
+++ b/drivers/usb/gadget/serial.c
@@ -240,7 +240,7 @@ struct gs_dev {
struct usb_ep *dev_notify_ep; /* address of notify endpoint */
struct usb_ep *dev_in_ep; /* address of in endpoint */
struct usb_ep *dev_out_ep; /* address of out endpoint */
- struct usb_endpoint_descriptor /* desciptor of notify ep */
+ struct usb_endpoint_descriptor /* descriptor of notify ep */
*dev_notify_ep_desc;
struct usb_endpoint_descriptor /* descriptor of in endpoint */
*dev_in_ep_desc;
diff --git a/drivers/usb/host/hc_crisv10.c b/drivers/usb/host/hc_crisv10.c
index 376f8a0..d9883d7 100644
--- a/drivers/usb/host/hc_crisv10.c
+++ b/drivers/usb/host/hc_crisv10.c
@@ -4329,7 +4329,7 @@ static int __init etrax_usb_hc_init(void)
bus->bus_name="ETRAX 100LX";
bus->hcpriv = hc;
- /* Initalize RH to the default address.
+ /* Initialize RH to the default address.
And make sure that we have no status change indication */
hc->rh.numports = 2; /* The RH has two ports */
hc->rh.devnum = 1;
diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c
index d309e29..a374b76 100644
--- a/drivers/usb/host/sl811-hcd.c
+++ b/drivers/usb/host/sl811-hcd.c
@@ -134,7 +134,7 @@ static void port_power(struct sl811 *sl811, int is_on)
/* This is a PIO-only HCD. Queueing appends URBs to the endpoint's queue,
* and may start I/O. Endpoint queues are scanned during completion irq
- * handlers (one per packet: ACK, NAK, faults, etc) and urb cancelation.
+ * handlers (one per packet: ACK, NAK, faults, etc) and urb cancellation.
*
* Using an external DMA engine to copy a packet at a time could work,
* though setup/teardown costs may be too big to make it worthwhile.
@@ -738,7 +738,7 @@ retry:
}
#endif
- /* port status seems wierd until after reset, so
+ /* port status seems weird until after reset, so
* force the reset and make khubd clean up later.
*/
sl811->port1 |= (1 << USB_PORT_FEAT_C_CONNECTION)
diff --git a/drivers/usb/image/mdc800.c b/drivers/usb/image/mdc800.c
index 5791723..a330a4b 100644
--- a/drivers/usb/image/mdc800.c
+++ b/drivers/usb/image/mdc800.c
@@ -23,7 +23,7 @@
*
*
* The driver brings the USB functions of the MDC800 to Linux.
- * To use the Camera you must support the USB Protocoll of the camera
+ * To use the Camera you must support the USB Protocol of the camera
* to the Kernel Node.
* The Driver uses a misc device Node. Create it with :
* mknod /dev/mustek c 180 32
diff --git a/drivers/usb/input/aiptek.c b/drivers/usb/input/aiptek.c
index 2d76be6..94ce2a9 100644
--- a/drivers/usb/input/aiptek.c
+++ b/drivers/usb/input/aiptek.c
@@ -386,7 +386,7 @@ static int aiptek_convert_from_2s_complement(unsigned char c)
* convention above.) I therefore have taken over REL_MISC and ABS_MISC
* (for relative and absolute reports, respectively) for communicating
* Proximity. Why two events? I thought it interesting to know if the
- * Proximity event occured while the tablet was in absolute or relative
+ * Proximity event occurred while the tablet was in absolute or relative
* mode.
*
* Other tablets use the notion of a certain minimum stylus pressure
diff --git a/drivers/usb/input/mtouchusb.c b/drivers/usb/input/mtouchusb.c
index 6b45a66..ab1a2a3 100644
--- a/drivers/usb/input/mtouchusb.c
+++ b/drivers/usb/input/mtouchusb.c
@@ -32,7 +32,7 @@
* Changed reset from standard USB dev reset to vendor reset
* Changed data sent to host from compensated to raw coordinates
* Eliminated vendor/product module params
- * Performed multiple successfull tests with an EXII-5010UC
+ * Performed multiple successful tests with an EXII-5010UC
*
* 1.5 02/27/2005 ddstreet@ieee.org
* Added module parameter to select raw or hw-calibrated coordinate reporting
diff --git a/drivers/usb/media/ov511.c b/drivers/usb/media/ov511.c
index d605182..036c485 100644
--- a/drivers/usb/media/ov511.c
+++ b/drivers/usb/media/ov511.c
@@ -5041,7 +5041,7 @@ ov6xx0_configure(struct usb_ov511 *ov)
{ OV511_I2C_BUS, 0x2a, 0x04 }, /* Disable framerate adjust */
// { OV511_I2C_BUS, 0x2b, 0xac }, /* Framerate; Set 2a[7] first */
{ OV511_I2C_BUS, 0x2d, 0x99 },
- { OV511_I2C_BUS, 0x33, 0xa0 }, /* Color Procesing Parameter */
+ { OV511_I2C_BUS, 0x33, 0xa0 }, /* Color Processing Parameter */
{ OV511_I2C_BUS, 0x34, 0xd2 }, /* Max A/D range */
{ OV511_I2C_BUS, 0x38, 0x8b },
{ OV511_I2C_BUS, 0x39, 0x40 },
diff --git a/drivers/usb/media/pwc/pwc-ctrl.c b/drivers/usb/media/pwc/pwc-ctrl.c
index 42352f5..42ec468 100644
--- a/drivers/usb/media/pwc/pwc-ctrl.c
+++ b/drivers/usb/media/pwc/pwc-ctrl.c
@@ -1100,7 +1100,7 @@ static inline int pwc_mpt_set_angle(struct pwc_device *pdev, int pan, int tilt)
unsigned char buf[4];
/* set new relative angle; angles are expressed in degrees * 100,
- but cam as .5 degree resolution, hence devide by 200. Also
+ but cam as .5 degree resolution, hence divide by 200. Also
the angle must be multiplied by 64 before it's send to
the cam (??)
*/
diff --git a/drivers/usb/media/pwc/pwc-if.c b/drivers/usb/media/pwc/pwc-if.c
index c53e226..cca47f4 100644
--- a/drivers/usb/media/pwc/pwc-if.c
+++ b/drivers/usb/media/pwc/pwc-if.c
@@ -272,7 +272,7 @@ static int pwc_allocate_buffers(struct pwc_device *pdev)
return -ENXIO;
}
#endif
- /* Allocate Isochronuous pipe buffers */
+ /* Allocate Isochronous pipe buffers */
for (i = 0; i < MAX_ISO_BUFS; i++) {
if (pdev->sbuf[i].data == NULL) {
kbuf = kmalloc(ISO_BUFFER_SIZE, GFP_KERNEL);
@@ -850,7 +850,7 @@ static int pwc_isoc_init(struct pwc_device *pdev)
if (pdev->vmax_packet_size < 0 || pdev->vmax_packet_size > ISO_MAX_FRAME_SIZE) {
Err("Failed to find packet size for video endpoint in current alternate setting.\n");
- return -ENFILE; /* Odd error, that should be noticable */
+ return -ENFILE; /* Odd error, that should be noticeable */
}
/* Set alternate interface */
@@ -2128,7 +2128,7 @@ static int __init usb_pwc_init(void)
if (leds[1] >= 0)
led_off = leds[1];
- /* Big device node whoopla. Basicly, it allows you to assign a
+ /* Big device node whoopla. Basically, it allows you to assign a
device node (/dev/videoX) to a camera, based on its type
& serial number. The format is [type[.serialnumber]:]node.
diff --git a/drivers/usb/media/pwc/pwc-ioctl.h b/drivers/usb/media/pwc/pwc-ioctl.h
index 65805ea..5f9cb08 100644
--- a/drivers/usb/media/pwc/pwc-ioctl.h
+++ b/drivers/usb/media/pwc/pwc-ioctl.h
@@ -75,7 +75,7 @@
#define PWC_FPS_SNAPSHOT 0x00400000
-/* structure for transfering x & y coordinates */
+/* structure for transferring x & y coordinates */
struct pwc_coord
{
int x, y; /* guess what */
diff --git a/drivers/usb/misc/legousbtower.c b/drivers/usb/misc/legousbtower.c
index dd4580c..7d06105 100644
--- a/drivers/usb/misc/legousbtower.c
+++ b/drivers/usb/misc/legousbtower.c
@@ -859,7 +859,7 @@ static int tower_probe (struct usb_interface *interface, const struct usb_device
info ("udev is NULL.");
}
- /* allocate memory for our device state and intialize it */
+ /* allocate memory for our device state and initialize it */
dev = kmalloc (sizeof(struct lego_usb_tower), GFP_KERNEL);
diff --git a/drivers/usb/net/zd1201.c b/drivers/usb/net/zd1201.c
index f98cb2a..341ae5f 100644
--- a/drivers/usb/net/zd1201.c
+++ b/drivers/usb/net/zd1201.c
@@ -183,7 +183,7 @@ static void zd1201_usbtx(struct urb *urb, struct pt_regs *regs)
return;
}
-/* Incomming data */
+/* Incoming data */
static void zd1201_usbrx(struct urb *urb, struct pt_regs *regs)
{
struct zd1201 *zd = urb->context;
@@ -772,7 +772,7 @@ static int zd1201_net_stop(struct net_device *dev)
/*
RFC 1042 encapsulates Ethernet frames in 802.11 frames
by prefixing them with 0xaa, 0xaa, 0x03) followed by a SNAP OID of 0
- (0x00, 0x00, 0x00). Zd requires an additionnal padding, copy
+ (0x00, 0x00, 0x00). Zd requires an additional padding, copy
of ethernet addresses, length of the standard RFC 1042 packet
and a command byte (which is nul for tx).
@@ -1098,7 +1098,7 @@ static int zd1201_get_range(struct net_device *dev,
/* Little bit of magic here: we only get the quality if we poll
* for it, and we never get an actual request to trigger such
- * a poll. Therefore we 'asume' that the user will soon ask for
+ * a poll. Therefore we 'assume' that the user will soon ask for
* the stats after asking the bssid.
*/
static int zd1201_get_wap(struct net_device *dev,
@@ -1108,7 +1108,7 @@ static int zd1201_get_wap(struct net_device *dev,
unsigned char buffer[6];
if (!zd1201_getconfig(zd, ZD1201_RID_COMMSQUALITY, buffer, 6)) {
- /* Unfortunatly the quality and noise reported is useless.
+ /* Unfortunately the quality and noise reported is useless.
they seem to be accumulators that increase until you
read them, unless we poll on a fixed interval we can't
use them
diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c
index d165f42..9db23de 100644
--- a/drivers/usb/serial/cypress_m8.c
+++ b/drivers/usb/serial/cypress_m8.c
@@ -234,7 +234,7 @@ static struct usb_serial_device_type cypress_hidcom_device = {
*****************************************************************************/
-/* This function can either set or retreive the current serial line settings */
+/* This function can either set or retrieve the current serial line settings */
static int cypress_serial_control (struct usb_serial_port *port, unsigned baud_mask, int data_bits, int stop_bits,
int parity_enable, int parity_type, int reset, int cypress_request_type)
{
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 0c4b435..52394f0 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -76,7 +76,7 @@
* Defererence pointers after any paranoid checks, not before.
*
* (21/Jun/2003) Erik Nygren
- * Added support for Home Electronics Tira-1 IR tranceiver using FT232BM chip.
+ * Added support for Home Electronics Tira-1 IR transceiver using FT232BM chip.
* See <http://www.home-electro.com/tira1.htm>. Only operates properly
* at 100000 and RTS-CTS, so set custom divisor mode on startup.
* Also force the Tira-1 and USB-UIRT to only use their custom baud rates.
@@ -91,7 +91,7 @@
* Minor whitespace and comment changes.
*
* (12/Jun/2003) David Norwood
- * Added support for USB-UIRT IR tranceiver using 8U232AM chip.
+ * Added support for USB-UIRT IR transceiver using 8U232AM chip.
* See <http://home.earthlink.net/~jrhees/USBUIRT/index.htm>. Only
* operates properly at 312500, so set custom divisor mode on startup.
*
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index 96be364..a52bb13 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -136,7 +136,7 @@
/*
* Home Electronics (www.home-electro.com) USB gadgets
*/
-#define FTDI_HE_TIRA1_PID 0xFA78 /* Tira-1 IR tranceiver */
+#define FTDI_HE_TIRA1_PID 0xFA78 /* Tira-1 IR transceiver */
/* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */
/* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */
diff --git a/drivers/usb/serial/io_usbvend.h b/drivers/usb/serial/io_usbvend.h
index 8c1fa5e..f1804fd 100644
--- a/drivers/usb/serial/io_usbvend.h
+++ b/drivers/usb/serial/io_usbvend.h
@@ -289,7 +289,7 @@
//
//
-// Edgeport Compatiblity Descriptor
+// Edgeport Compatibility Descriptor
//
// This descriptor is only returned by Edgeport-compatible devices
// supporting the EPiC spec. True ION devices do not return this
diff --git a/drivers/usb/serial/keyspan_usa90msg.h b/drivers/usb/serial/keyspan_usa90msg.h
index dd935b6..86708ec 100644
--- a/drivers/usb/serial/keyspan_usa90msg.h
+++ b/drivers/usb/serial/keyspan_usa90msg.h
@@ -19,7 +19,7 @@
This file is available under a BSD-style copyright
- 2. The name of InnoSys Incorprated may not be used to endorse or promote
+ 2. The name of InnoSys Incorporated may not be used to endorse or promote
products derived from this software without specific prior written
permission.
diff --git a/drivers/usb/storage/shuttle_usbat.c b/drivers/usb/storage/shuttle_usbat.c
index 7eff03d..f3b6028 100644
--- a/drivers/usb/storage/shuttle_usbat.c
+++ b/drivers/usb/storage/shuttle_usbat.c
@@ -786,7 +786,7 @@ static int usbat_flash_check_media(struct us_data *us,
if (rc != USB_STOR_XFER_GOOD)
return USB_STOR_TRANSPORT_ERROR;
- // Check for media existance
+ // Check for media existence
rc = usbat_flash_check_media_present(uio);
if (rc == USBAT_FLASH_MEDIA_NONE) {
info->sense_key = 0x02;
diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index 99e8249..d2891f4 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -1,5 +1,5 @@
/* Driver for USB Mass Storage compliant devices
- * Ununsual Devices File
+ * Unusual Devices File
*
* $Id: unusual_devs.h,v 1.32 2002/02/25 02:41:24 mdharm Exp $
*
OpenPOWER on IntegriCloud