diff options
-rw-r--r-- | arch/arm/mach-mx3/Kconfig | 9 | ||||
-rw-r--r-- | arch/arm/mach-mx3/mx31ads.c | 294 |
2 files changed, 303 insertions, 0 deletions
diff --git a/arch/arm/mach-mx3/Kconfig b/arch/arm/mach-mx3/Kconfig index e79659e..6fea541 100644 --- a/arch/arm/mach-mx3/Kconfig +++ b/arch/arm/mach-mx3/Kconfig @@ -8,6 +8,15 @@ config MACH_MX31ADS Include support for MX31ADS platform. This includes specific configurations for the board and its peripherals. +config MACH_MX31ADS_WM1133_EV1 + bool "Support Wolfson Microelectronics 1133-EV1 module" + depends on MACH_MX31ADS + select MFD_WM8350_CONFIG_MODE_0 + select MFD_WM8352_CONFIG_MODE_0 + help + Include support for the Wolfson Microelectronics 1133-EV1 PMU + and audio module for the MX31ADS platform. + config MACH_PCM037 bool "Support Phytec pcm037 platforms" help diff --git a/arch/arm/mach-mx3/mx31ads.c b/arch/arm/mach-mx3/mx31ads.c index 7941db3..5c76ac5 100644 --- a/arch/arm/mach-mx3/mx31ads.c +++ b/arch/arm/mach-mx3/mx31ads.c @@ -22,6 +22,8 @@ #include <linux/init.h> #include <linux/clk.h> #include <linux/serial_8250.h> +#include <linux/gpio.h> +#include <linux/i2c.h> #include <linux/irq.h> #include <mach/hardware.h> @@ -35,6 +37,12 @@ #include <mach/imx-uart.h> #include <mach/iomux-mx3.h> +#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1 +#include <linux/mfd/wm8350/audio.h> +#include <linux/mfd/wm8350/core.h> +#include <linux/mfd/wm8350/pmic.h> +#endif + #include "devices.h" /*! @@ -194,6 +202,291 @@ static void __init mx31ads_init_expio(void) set_irq_chained_handler(EXPIO_PARENT_INT, mx31ads_expio_irq_handler); } +#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1 +/* This section defines setup for the Wolfson Microelectronics + * 1133-EV1 PMU/audio board. When other PMU boards are supported the + * regulator definitions may be shared with them, but for now they can + * only be used with this board so would generate warnings about + * unused statics and some of the configuration is specific to this + * module. + */ + +/* CPU */ +static struct regulator_consumer_supply sw1a_consumers[] = { + { + .supply = "cpu_vcc", + } +}; + +static struct regulator_init_data sw1a_data = { + .constraints = { + .name = "SW1A", + .min_uV = 1275000, + .max_uV = 1600000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_MODE, + .valid_modes_mask = REGULATOR_MODE_NORMAL | + REGULATOR_MODE_FAST, + .state_mem = { + .uV = 1400000, + .mode = REGULATOR_MODE_NORMAL, + .enabled = 1, + }, + .initial_state = PM_SUSPEND_MEM, + .always_on = 1, + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(sw1a_consumers), + .consumer_supplies = sw1a_consumers, +}; + +/* System IO - High */ +static struct regulator_init_data viohi_data = { + .constraints = { + .name = "VIOHO", + .min_uV = 2800000, + .max_uV = 2800000, + .state_mem = { + .uV = 2800000, + .mode = REGULATOR_MODE_NORMAL, + .enabled = 1, + }, + .initial_state = PM_SUSPEND_MEM, + .always_on = 1, + .boot_on = 1, + }, +}; + +/* System IO - Low */ +static struct regulator_init_data violo_data = { + .constraints = { + .name = "VIOLO", + .min_uV = 1800000, + .max_uV = 1800000, + .state_mem = { + .uV = 1800000, + .mode = REGULATOR_MODE_NORMAL, + .enabled = 1, + }, + .initial_state = PM_SUSPEND_MEM, + .always_on = 1, + .boot_on = 1, + }, +}; + +/* DDR RAM */ +static struct regulator_init_data sw2a_data = { + .constraints = { + .name = "SW2A", + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .state_mem = { + .uV = 1800000, + .mode = REGULATOR_MODE_NORMAL, + .enabled = 1, + }, + .state_disk = { + .mode = REGULATOR_MODE_NORMAL, + .enabled = 0, + }, + .always_on = 1, + .boot_on = 1, + .initial_state = PM_SUSPEND_MEM, + }, +}; + +static struct regulator_init_data ldo1_data = { + .constraints = { + .name = "VCAM/VMMC1/VMMC2", + .min_uV = 2800000, + .max_uV = 2800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + }, +}; + +static struct regulator_consumer_supply ldo2_consumers[] = { + { + .supply = "AVDD", + }, + { + .supply = "HPVDD", + }, +}; + +/* CODEC and SIM */ +static struct regulator_init_data ldo2_data = { + .constraints = { + .name = "VESIM/VSIM/AVDD", + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(ldo2_consumers), + .consumer_supplies = ldo2_consumers, +}; + +/* General */ +static struct regulator_init_data vdig_data = { + .constraints = { + .name = "VDIG", + .min_uV = 1500000, + .max_uV = 1500000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + .always_on = 1, + .boot_on = 1, + }, +}; + +/* Tranceivers */ +static struct regulator_init_data ldo4_data = { + .constraints = { + .name = "VRF1/CVDD_2.775", + .min_uV = 2500000, + .max_uV = 2500000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .apply_uV = 1, + .always_on = 1, + .boot_on = 1, + }, +}; + +static struct wm8350_led_platform_data wm8350_led_data = { + .name = "wm8350:white", + .default_trigger = "heartbeat", + .max_uA = 27899, +}; + +static struct wm8350_audio_platform_data imx32ads_wm8350_setup = { + .vmid_discharge_msecs = 1000, + .drain_msecs = 30, + .cap_discharge_msecs = 700, + .vmid_charge_msecs = 700, + .vmid_s_curve = WM8350_S_CURVE_SLOW, + .dis_out4 = WM8350_DISCHARGE_SLOW, + .dis_out3 = WM8350_DISCHARGE_SLOW, + .dis_out2 = WM8350_DISCHARGE_SLOW, + .dis_out1 = WM8350_DISCHARGE_SLOW, + .vroi_out4 = WM8350_TIE_OFF_500R, + .vroi_out3 = WM8350_TIE_OFF_500R, + .vroi_out2 = WM8350_TIE_OFF_500R, + .vroi_out1 = WM8350_TIE_OFF_500R, + .vroi_enable = 0, + .codec_current_on = WM8350_CODEC_ISEL_1_0, + .codec_current_standby = WM8350_CODEC_ISEL_0_5, + .codec_current_charge = WM8350_CODEC_ISEL_1_5, +}; + +static int mx31_wm8350_init(struct wm8350 *wm8350) +{ + int i; + + wm8350_gpio_config(wm8350, 0, WM8350_GPIO_DIR_IN, + WM8350_GPIO0_PWR_ON_IN, WM8350_GPIO_ACTIVE_LOW, + WM8350_GPIO_PULL_UP, WM8350_GPIO_INVERT_OFF, + WM8350_GPIO_DEBOUNCE_ON); + + wm8350_gpio_config(wm8350, 3, WM8350_GPIO_DIR_IN, + WM8350_GPIO3_PWR_OFF_IN, WM8350_GPIO_ACTIVE_HIGH, + WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF, + WM8350_GPIO_DEBOUNCE_ON); + + wm8350_gpio_config(wm8350, 4, WM8350_GPIO_DIR_IN, + WM8350_GPIO4_MR_IN, WM8350_GPIO_ACTIVE_HIGH, + WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF, + WM8350_GPIO_DEBOUNCE_OFF); + + wm8350_gpio_config(wm8350, 7, WM8350_GPIO_DIR_IN, + WM8350_GPIO7_HIBERNATE_IN, WM8350_GPIO_ACTIVE_HIGH, + WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF, + WM8350_GPIO_DEBOUNCE_OFF); + + wm8350_gpio_config(wm8350, 6, WM8350_GPIO_DIR_OUT, + WM8350_GPIO6_SDOUT_OUT, WM8350_GPIO_ACTIVE_HIGH, + WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF, + WM8350_GPIO_DEBOUNCE_OFF); + + wm8350_gpio_config(wm8350, 8, WM8350_GPIO_DIR_OUT, + WM8350_GPIO8_VCC_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW, + WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF, + WM8350_GPIO_DEBOUNCE_OFF); + + wm8350_gpio_config(wm8350, 9, WM8350_GPIO_DIR_OUT, + WM8350_GPIO9_BATT_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW, + WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF, + WM8350_GPIO_DEBOUNCE_OFF); + + /* Fix up for our own supplies. */ + for (i = 0; i < ARRAY_SIZE(ldo2_consumers); i++) + ldo2_consumers[i].dev = wm8350->dev; + + wm8350_register_regulator(wm8350, WM8350_DCDC_1, &sw1a_data); + wm8350_register_regulator(wm8350, WM8350_DCDC_3, &viohi_data); + wm8350_register_regulator(wm8350, WM8350_DCDC_4, &violo_data); + wm8350_register_regulator(wm8350, WM8350_DCDC_6, &sw2a_data); + wm8350_register_regulator(wm8350, WM8350_LDO_1, &ldo1_data); + wm8350_register_regulator(wm8350, WM8350_LDO_2, &ldo2_data); + wm8350_register_regulator(wm8350, WM8350_LDO_3, &vdig_data); + wm8350_register_regulator(wm8350, WM8350_LDO_4, &ldo4_data); + + /* LEDs */ + wm8350_dcdc_set_slot(wm8350, WM8350_DCDC_5, 1, 1, + WM8350_DC5_ERRACT_SHUTDOWN_CONV); + wm8350_isink_set_flash(wm8350, WM8350_ISINK_A, + WM8350_ISINK_FLASH_DISABLE, + WM8350_ISINK_FLASH_TRIG_BIT, + WM8350_ISINK_FLASH_DUR_32MS, + WM8350_ISINK_FLASH_ON_INSTANT, + WM8350_ISINK_FLASH_OFF_INSTANT, + WM8350_ISINK_FLASH_MODE_EN); + wm8350_dcdc25_set_mode(wm8350, WM8350_DCDC_5, + WM8350_ISINK_MODE_BOOST, + WM8350_ISINK_ILIM_NORMAL, + WM8350_DC5_RMP_20V, + WM8350_DC5_FBSRC_ISINKA); + wm8350_register_led(wm8350, 0, WM8350_DCDC_5, WM8350_ISINK_A, + &wm8350_led_data); + + wm8350->codec.platform_data = &imx32ads_wm8350_setup; + + return 0; +} + +static struct wm8350_platform_data __initdata mx31_wm8350_pdata = { + .init = mx31_wm8350_init, +}; +#endif + +#if defined(CONFIG_I2C_IMX) || defined(CONFIG_I2C_IMX_MODULE) +static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = { +#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1 + { + I2C_BOARD_INFO("wm8350", 0x1a), + .platform_data = &mx31_wm8350_pdata, + .irq = IOMUX_TO_IRQ(MX31_PIN_GPIO1_3), + }, +#endif +}; + +static void mxc_init_i2c(void) +{ + i2c_register_board_info(1, mx31ads_i2c1_devices, + ARRAY_SIZE(mx31ads_i2c1_devices)); + + mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1)); + mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1)); + + mxc_register_device(&mxc_i2c_device1, NULL); +} +#else +static void mxc_init_i2c(void) +{ +} +#endif + /*! * This structure defines static mappings for the i.MX31ADS board. */ @@ -243,6 +536,7 @@ static void __init mxc_board_init(void) { mxc_init_extuart(); mxc_init_imx_uart(); + mxc_init_i2c(); } static void __init mx31ads_timer_init(void) |