summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--arch/mips/au1000/mtx-1/board_setup.c4
-rw-r--r--arch/mips/au1000/pb1000/board_setup.c6
-rw-r--r--arch/mips/au1000/pb1100/board_setup.c4
-rw-r--r--arch/mips/au1000/pb1500/board_setup.c6
4 files changed, 10 insertions, 10 deletions
diff --git a/arch/mips/au1000/mtx-1/board_setup.c b/arch/mips/au1000/mtx-1/board_setup.c
index 7bc5af8..2c460c1 100644
--- a/arch/mips/au1000/mtx-1/board_setup.c
+++ b/arch/mips/au1000/mtx-1/board_setup.c
@@ -54,11 +54,11 @@ void board_reset (void)
void __init board_setup(void)
{
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
// enable USB power switch
au_writel( au_readl(GPIO2_DIR) | 0x10, GPIO2_DIR );
au_writel( 0x100000, GPIO2_OUTPUT );
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
#ifdef CONFIG_PCI
#if defined(__MIPSEB__)
diff --git a/arch/mips/au1000/pb1000/board_setup.c b/arch/mips/au1000/pb1000/board_setup.c
index 824cfaf..0aed891 100644
--- a/arch/mips/au1000/pb1000/board_setup.c
+++ b/arch/mips/au1000/pb1000/board_setup.c
@@ -54,7 +54,7 @@ void __init board_setup(void)
au_writel(0, SYS_PINSTATERD);
udelay(100);
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
@@ -102,7 +102,7 @@ void __init board_setup(void)
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
#endif
au_writel(sys_clksrc, SYS_CLKSRC);
@@ -116,7 +116,7 @@ void __init board_setup(void)
au_writel(pin_func, SYS_PINFUNC);
au_writel(0x2800, SYS_TRIOUTCLR);
au_writel(0x0030, SYS_OUTPUTCLR);
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
// make gpio 15 an input (for interrupt line)
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x100);
diff --git a/arch/mips/au1000/pb1100/board_setup.c b/arch/mips/au1000/pb1100/board_setup.c
index 6bc1f8e..259ca05 100644
--- a/arch/mips/au1000/pb1100/board_setup.c
+++ b/arch/mips/au1000/pb1100/board_setup.c
@@ -54,7 +54,7 @@ void __init board_setup(void)
au_writel(0, SYS_PININPUTEN);
udelay(100);
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
{
u32 pin_func, sys_freqctrl, sys_clksrc;
@@ -98,7 +98,7 @@ void __init board_setup(void)
pin_func |= 0x8000;
au_writel(pin_func, SYS_PINFUNC);
}
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
/* Enable sys bus clock divider when IDLE state or no bus activity. */
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
diff --git a/arch/mips/au1000/pb1500/board_setup.c b/arch/mips/au1000/pb1500/board_setup.c
index c9b6556..a2d850d 100644
--- a/arch/mips/au1000/pb1500/board_setup.c
+++ b/arch/mips/au1000/pb1500/board_setup.c
@@ -56,7 +56,7 @@ void __init board_setup(void)
au_writel(0, SYS_PINSTATERD);
udelay(100);
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* GPIO201 is input for PCMCIA card detect */
/* GPIO203 is input for PCMCIA interrupt request */
@@ -85,7 +85,7 @@ void __init board_setup(void)
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
-#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
#endif
au_writel(sys_clksrc, SYS_CLKSRC);
@@ -95,7 +95,7 @@ void __init board_setup(void)
// 2nd USB port is USB host
pin_func |= 0x8000;
au_writel(pin_func, SYS_PINFUNC);
-#endif // defined (CONFIG_USB_OHCI)
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
OpenPOWER on IntegriCloud