diff options
| -rw-r--r-- | drivers/thermal/imx_thermal.c | 56 |
1 files changed, 41 insertions, 15 deletions
diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c index c8fe3ca..c5547bd 100644 --- a/drivers/thermal/imx_thermal.c +++ b/drivers/thermal/imx_thermal.c @@ -55,6 +55,7 @@ #define TEMPSENSE2_PANIC_VALUE_SHIFT 16 #define TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000 +#define OCOTP_MEM0 0x0480 #define OCOTP_ANA1 0x04e0 /* The driver supports 1 passive trip point and 1 critical trip point */ @@ -64,12 +65,6 @@ enum imx_thermal_trip { IMX_TRIP_NUM, }; -/* - * It defines the temperature in millicelsius for passive trip point - * that will trigger cooling action when crossed. - */ -#define IMX_TEMP_PASSIVE 85000 - #define IMX_POLLING_DELAY 2000 /* millisecond */ #define IMX_PASSIVE_DELAY 1000 @@ -100,12 +95,14 @@ struct imx_thermal_data { u32 c1, c2; /* See formula in imx_get_sensor_data() */ int temp_passive; int temp_critical; + int temp_max; int alarm_temp; int last_temp; bool irq_enabled; int irq; struct clk *thermal_clk; const struct thermal_soc_data *socdata; + const char *temp_grade; }; static void imx_set_panic_temp(struct imx_thermal_data *data, @@ -285,10 +282,12 @@ static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip, { struct imx_thermal_data *data = tz->devdata; + /* do not allow changing critical threshold */ if (trip == IMX_TRIP_CRITICAL) return -EPERM; - if (temp < 0 || temp > IMX_TEMP_PASSIVE) + /* do not allow passive to be set higher than critical */ + if (temp < 0 || temp > data->temp_critical) return -EINVAL; data->temp_passive = temp; @@ -404,17 +403,39 @@ static int imx_get_sensor_data(struct platform_device *pdev) data->c1 = temp64; data->c2 = n1 * data->c1 + 1000 * t1; - /* - * Set the default passive cooling trip point, - * can be changed from userspace. - */ - data->temp_passive = IMX_TEMP_PASSIVE; + /* use OTP for thermal grade */ + ret = regmap_read(map, OCOTP_MEM0, &val); + if (ret) { + dev_err(&pdev->dev, "failed to read temp grade: %d\n", ret); + return ret; + } + + /* The maximum die temp is specified by the Temperature Grade */ + switch ((val >> 6) & 0x3) { + case 0: /* Commercial (0 to 95C) */ + data->temp_grade = "Commercial"; + data->temp_max = 95000; + break; + case 1: /* Extended Commercial (-20 to 105C) */ + data->temp_grade = "Extended Commercial"; + data->temp_max = 105000; + break; + case 2: /* Industrial (-40 to 105C) */ + data->temp_grade = "Industrial"; + data->temp_max = 105000; + break; + case 3: /* Automotive (-40 to 125C) */ + data->temp_grade = "Automotive"; + data->temp_max = 125000; + break; + } /* - * The maximum die temperature set to 20 C higher than - * IMX_TEMP_PASSIVE. + * Set the critical trip point at 5C under max + * Set the passive trip point at 10C under max (can change via sysfs) */ - data->temp_critical = 1000 * 20 + data->temp_passive; + data->temp_critical = data->temp_max - (1000 * 5); + data->temp_passive = data->temp_max - (1000 * 10); return 0; } @@ -551,6 +572,11 @@ static int imx_thermal_probe(struct platform_device *pdev) return ret; } + dev_info(&pdev->dev, "%s CPU temperature grade - max:%dC" + " critical:%dC passive:%dC\n", data->temp_grade, + data->temp_max / 1000, data->temp_critical / 1000, + data->temp_passive / 1000); + /* Enable measurements at ~ 10 Hz */ regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ); measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */ |
