diff options
-rw-r--r-- | Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt | 162 | ||||
-rw-r--r-- | include/dt-bindings/pinctrl/qcom,pmic-mpp.h | 44 |
2 files changed, 206 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt new file mode 100644 index 0000000..854774b1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -0,0 +1,162 @@ +Qualcomm PMIC Multi-Purpose Pin (MPP) block + +This binding describes the MPP block(s) found in the 8xxx series +of PMIC's from Qualcomm. + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain one of: + "qcom,pm8841-mpp", + "qcom,pm8941-mpp", + "qcom,pma8084-mpp", + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register base of the MPP block and length. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Must contain an array of encoded interrupt specifiers for + each available MPP + +- gpio-controller: + Usage: required + Value type: <none> + Definition: Mark the device node as a GPIO controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: Must be 2; + the first cell will be used to define MPP number and the + second denotes the flags for this MPP + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin or a list of pins. This configuration can include the +mux function to select on those pin(s), and various pin configuration +parameters, as listed below. + +SUBNODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of MPP pins affected by the properties specified in + this subnode. Valid pins are: + mpp1-mpp4 for pm8841 + mpp1-mpp8 for pm8941 + mpp1-mpp4 for pma8084 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Valid values are: + "normal", + "paired", + "dtest1", + "dtest2", + "dtest3", + "dtest4" + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configured as no pull. + +- bias-pull-up: + Usage: optional + Value type: <u32> + Definition: The specified pins should be configured as pull up. + Valid values are 600, 10000 and 30000 in bidirectional mode + only, i.e. when operating in qcom,analog-mode and input and + outputs are enabled. The hardware ignores the configuration + when operating in other modes. + +- bias-high-impedance: + Usage: optional + Value type: <none> + Definition: The specified pins will put in high-Z mode and disabled. + +- input-enable: + Usage: optional + Value type: <none> + Definition: The specified pins are put in input mode, i.e. their input + buffer is enabled + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + +- power-source: + Usage: optional + Value type: <u32> + Definition: Selects the power source for the specified pins. Valid power + sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +- qcom,analog-mode: + Usage: optional + Value type: <none> + Definition: Selects Analog mode of operation: combined with input-enable + and/or output-high, output-low MPP could operate as + Bidirectional Logic, Analog Input, Analog Output. + +- qcom,amux-route: + Usage: optional + Value type: <u32> + Definition: Selects the source for analog input. Valid values are + defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> + PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6... + +Example: + + mpps@a000 { + compatible = "qcom,pm8841-mpp"; + reg = <0xa000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>; + + pinctrl-names = "default"; + pinctrl-0 = <&pm8841_default>; + + pm8841_default: default { + gpio { + pins = "mpp1", "mpp2", "mpp3", "mpp4"; + function = "normal"; + input-enable; + power-source = <PM8841_MPP_S3>; + }; + }; + }; diff --git a/include/dt-bindings/pinctrl/qcom,pmic-mpp.h b/include/dt-bindings/pinctrl/qcom,pmic-mpp.h new file mode 100644 index 0000000..d2c7dab --- /dev/null +++ b/include/dt-bindings/pinctrl/qcom,pmic-mpp.h @@ -0,0 +1,44 @@ +/* + * This header provides constants for the Qualcomm PMIC's + * Multi-Purpose Pin binding. + */ + +#ifndef _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H +#define _DT_BINDINGS_PINCTRL_QCOM_PMIC_MPP_H + +/* power-source */ +#define PM8841_MPP_VPH 0 +#define PM8841_MPP_S3 2 + +#define PM8941_MPP_VPH 0 +#define PM8941_MPP_L1 1 +#define PM8941_MPP_S3 2 +#define PM8941_MPP_L6 3 + +#define PMA8084_MPP_VPH 0 +#define PMA8084_MPP_L1 1 +#define PMA8084_MPP_S4 2 +#define PMA8084_MPP_L6 3 + +/* + * Analog Input - Set the source for analog input. + * To be used with "qcom,amux-route" property + */ +#define PMIC_MPP_AMUX_ROUTE_CH5 0 +#define PMIC_MPP_AMUX_ROUTE_CH6 1 +#define PMIC_MPP_AMUX_ROUTE_CH7 2 +#define PMIC_MPP_AMUX_ROUTE_CH8 3 +#define PMIC_MPP_AMUX_ROUTE_ABUS1 4 +#define PMIC_MPP_AMUX_ROUTE_ABUS2 5 +#define PMIC_MPP_AMUX_ROUTE_ABUS3 6 +#define PMIC_MPP_AMUX_ROUTE_ABUS4 7 + +/* To be used with "function" */ +#define PMIC_MPP_FUNC_NORMAL "normal" +#define PMIC_MPP_FUNC_PAIRED "paired" +#define PMIC_MPP_FUNC_DTEST1 "dtest1" +#define PMIC_MPP_FUNC_DTEST2 "dtest2" +#define PMIC_MPP_FUNC_DTEST3 "dtest3" +#define PMIC_MPP_FUNC_DTEST4 "dtest4" + +#endif |