diff options
| -rw-r--r-- | Documentation/devicetree/bindings/pci/designware-pcie.txt | 74 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt | 38 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt | 65 | ||||
| -rw-r--r-- | drivers/bus/mvebu-mbus.c | 22 | ||||
| -rw-r--r-- | drivers/pci/host/pci-exynos.c | 1 | ||||
| -rw-r--r-- | drivers/pci/host/pci-imx6.c | 1 | ||||
| -rw-r--r-- | drivers/pci/host/pci-mvebu.c | 102 | ||||
| -rw-r--r-- | drivers/pci/host/pci-tegra.c | 7 | ||||
| -rw-r--r-- | drivers/pci/host/pcie-designware.c | 26 | ||||
| -rw-r--r-- | drivers/pci/host/pcie-designware.h | 1 |
10 files changed, 222 insertions, 115 deletions
diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index d6fae13f..d0d15ee 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -1,15 +1,7 @@ * Synopsys Designware PCIe interface Required properties: -- compatible: should contain "snps,dw-pcie" to identify the - core, plus an identifier for the specific instance, such - as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie". -- reg: base addresses and lengths of the pcie controller, - the phy controller, additional register for the phy controller. -- interrupts: interrupt values for level interrupt, - pulse interrupt, special interrupt. -- clocks: from common clock binding: handle to pci clock. -- clock-names: from common clock binding: should be "pcie" and "pcie_bus". +- compatible: should contain "snps,dw-pcie" to identify the core. - #address-cells: set to <3> - #size-cells: set to <2> - device_type: set to "pci" @@ -19,65 +11,11 @@ Required properties: to define the mapping of the PCIe interface to interrupt numbers. - num-lanes: number of lanes to use +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "pcie" + - "pcie_bus" Optional properties: - reset-gpio: gpio pin number of power good signal - -Optional properties for fsl,imx6q-pcie -- power-on-gpio: gpio pin number of power-enable signal -- wake-up-gpio: gpio pin number of incoming wakeup signal -- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal - -Example: - -SoC specific DT Entry: - - pcie@290000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x290000 0x1000 - 0x270000 0x1000 - 0x271000 0x40>; - interrupts = <0 20 0>, <0 21 0>, <0 22 0>; - clocks = <&clock 28>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 53>; - num-lanes = <4>; - }; - - pcie@2a0000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x2a0000 0x1000 - 0x272000 0x1000 - 0x271040 0x40>; - interrupts = <0 23 0>, <0 24 0>, <0 25 0>; - clocks = <&clock 29>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0x0 0 &gic 56>; - num-lanes = <4>; - }; - -Board specific DT Entry: - - pcie@290000 { - reset-gpio = <&pin_ctrl 5 0>; - }; - - pcie@2a0000 { - reset-gpio = <&pin_ctrl 22 0>; - }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt new file mode 100644 index 0000000..9455fd0 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -0,0 +1,38 @@ +* Freescale i.MX6 PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "fsl,imx6q-pcie" +- reg: base addresse and length of the pcie controller +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- clock-names: Must include the following additional entries: + - "pcie_phy" + +Example: + + pcie@0x01000000 { + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; + reg = <0x01ffc000 0x4000>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 + 0x81000000 0 0 0x01f80000 0 0x00010000 + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; + num-lanes = <1>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 144>, <&clks 206>, <&clks 189>; + clock-names = "pcie", "pcie_bus", "pcie_phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt new file mode 100644 index 0000000..4f9d23d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -0,0 +1,65 @@ +* Samsung Exynos 5440 PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "samsung,exynos5440-pcie" +- reg: base addresses and lengths of the pcie controller, + the phy controller, additional register for the phy controller. +- interrupts: A list of interrupt outputs for level interrupt, + pulse interrupt, special interrupt. + +Example: + +SoC specific DT Entry: + + pcie@290000 { + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; + reg = <0x290000 0x1000 + 0x270000 0x1000 + 0x271000 0x40>; + interrupts = <0 20 0>, <0 21 0>, <0 22 0>; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; + }; + + pcie@2a0000 { + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; + reg = <0x2a0000 0x1000 + 0x272000 0x1000 + 0x271040 0x40>; + interrupts = <0 23 0>, <0 24 0>, <0 25 0>; + clocks = <&clock 29>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; + }; + +Board specific DT Entry: + + pcie@290000 { + reset-gpio = <&pin_ctrl 5 0>; + }; + + pcie@2a0000 { + reset-gpio = <&pin_ctrl 22 0>; + }; diff --git a/drivers/bus/mvebu-mbus.c b/drivers/bus/mvebu-mbus.c index 293e2e0..00b7344 100644 --- a/drivers/bus/mvebu-mbus.c +++ b/drivers/bus/mvebu-mbus.c @@ -56,6 +56,7 @@ #include <linux/of.h> #include <linux/of_address.h> #include <linux/debugfs.h> +#include <linux/log2.h> /* * DDR target is the same on all platforms. @@ -222,12 +223,6 @@ static int mvebu_mbus_window_conflicts(struct mvebu_mbus_state *mbus, */ if ((u64)base < wend && end > wbase) return 0; - - /* - * Check if target/attribute conflicts - */ - if (target == wtarget && attr == wattr) - return 0; } return 1; @@ -266,6 +261,17 @@ static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus, mbus->soc->win_cfg_offset(win); u32 ctrl, remap_addr; + if (!is_power_of_2(size)) { + WARN(true, "Invalid MBus window size: 0x%zx\n", size); + return -EINVAL; + } + + if ((base & (phys_addr_t)(size - 1)) != 0) { + WARN(true, "Invalid MBus base/size: %pa len 0x%zx\n", &base, + size); + return -EINVAL; + } + ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) | (attr << WIN_CTRL_ATTR_SHIFT) | (target << WIN_CTRL_TGT_SHIFT) | @@ -413,6 +419,10 @@ static int mvebu_devs_debug_show(struct seq_file *seq, void *v) win, (unsigned long long)wbase, (unsigned long long)(wbase + wsize), wtarget, wattr); + if (!is_power_of_2(wsize) || + ((wbase & (u64)(wsize - 1)) != 0)) + seq_puts(seq, " (Invalid base/size!!)"); + if (win < mbus->soc->num_remappable_wins) { seq_printf(seq, " (remap %016llx)\n", (unsigned long long)wremap); diff --git a/drivers/pci/host/pci-exynos.c b/drivers/pci/host/pci-exynos.c index 1632661..c5d0ca3 100644 --- a/drivers/pci/host/pci-exynos.c +++ b/drivers/pci/host/pci-exynos.c @@ -545,7 +545,6 @@ static int __init add_pcie_port(struct pcie_port *pp, pp->root_bus_nr = -1; pp->ops = &exynos_pcie_host_ops; - spin_lock_init(&pp->conf_lock); ret = dw_pcie_host_init(pp); if (ret) { dev_err(&pdev->dev, "failed to initialize host\n"); diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c index a5645ae..a568efa 100644 --- a/drivers/pci/host/pci-imx6.c +++ b/drivers/pci/host/pci-imx6.c @@ -507,7 +507,6 @@ static int __init imx6_add_pcie_port(struct pcie_port *pp, pp->root_bus_nr = -1; pp->ops = &imx6_pcie_host_ops; - spin_lock_init(&pp->conf_lock); ret = dw_pcie_host_init(pp); if (ret) { dev_err(&pdev->dev, "failed to initialize host\n"); diff --git a/drivers/pci/host/pci-mvebu.c b/drivers/pci/host/pci-mvebu.c index d3d1cfd..7f45032 100644 --- a/drivers/pci/host/pci-mvebu.c +++ b/drivers/pci/host/pci-mvebu.c @@ -113,7 +113,6 @@ struct mvebu_pcie { struct mvebu_pcie_port { char *name; void __iomem *base; - spinlock_t conf_lock; u32 port; u32 lane; int devfn; @@ -293,6 +292,60 @@ static int mvebu_pcie_hw_wr_conf(struct mvebu_pcie_port *port, return PCIBIOS_SUCCESSFUL; } +/* + * Remove windows, starting from the largest ones to the smallest + * ones. + */ +static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port, + phys_addr_t base, size_t size) +{ + while (size) { + size_t sz = 1 << (fls(size) - 1); + + mvebu_mbus_del_window(base, sz); + base += sz; + size -= sz; + } +} + +/* + * MBus windows can only have a power of two size, but PCI BARs do not + * have this constraint. Therefore, we have to split the PCI BAR into + * areas each having a power of two size. We start from the largest + * one (i.e highest order bit set in the size). + */ +static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port, + unsigned int target, unsigned int attribute, + phys_addr_t base, size_t size, + phys_addr_t remap) +{ + size_t size_mapped = 0; + + while (size) { + size_t sz = 1 << (fls(size) - 1); + int ret; + + ret = mvebu_mbus_add_window_remap_by_id(target, attribute, base, + sz, remap); + if (ret) { + phys_addr_t end = base + sz - 1; + + dev_err(&port->pcie->pdev->dev, + "Could not create MBus window at [mem %pa-%pa]: %d\n", + &base, &end, ret); + mvebu_pcie_del_windows(port, base - size_mapped, + size_mapped); + return; + } + + size -= sz; + size_mapped += sz; + base += sz; + if (remap != MVEBU_MBUS_NO_REMAP) + remap += sz; + } +} + static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port) { phys_addr_t iobase; @@ -304,8 +357,8 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port) /* If a window was configured, remove it */ if (port->iowin_base) { - mvebu_mbus_del_window(port->iowin_base, - port->iowin_size); + mvebu_pcie_del_windows(port, port->iowin_base, + port->iowin_size); port->iowin_base = 0; port->iowin_size = 0; } @@ -331,11 +384,11 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port) port->iowin_base = port->pcie->io.start + iobase; port->iowin_size = ((0xFFF | ((port->bridge.iolimit & 0xF0) << 8) | (port->bridge.iolimitupper << 16)) - - iobase); + iobase) + 1; - mvebu_mbus_add_window_remap_by_id(port->io_target, port->io_attr, - port->iowin_base, port->iowin_size, - iobase); + mvebu_pcie_add_windows(port, port->io_target, port->io_attr, + port->iowin_base, port->iowin_size, + iobase); } static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port) @@ -346,8 +399,8 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port) /* If a window was configured, remove it */ if (port->memwin_base) { - mvebu_mbus_del_window(port->memwin_base, - port->memwin_size); + mvebu_pcie_del_windows(port, port->memwin_base, + port->memwin_size); port->memwin_base = 0; port->memwin_size = 0; } @@ -364,10 +417,11 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port) port->memwin_base = ((port->bridge.membase & 0xFFF0) << 16); port->memwin_size = (((port->bridge.memlimit & 0xFFF0) << 16) | 0xFFFFF) - - port->memwin_base; + port->memwin_base + 1; - mvebu_mbus_add_window_by_id(port->mem_target, port->mem_attr, - port->memwin_base, port->memwin_size); + mvebu_pcie_add_windows(port, port->mem_target, port->mem_attr, + port->memwin_base, port->memwin_size, + MVEBU_MBUS_NO_REMAP); } /* @@ -585,7 +639,6 @@ static int mvebu_pcie_wr_conf(struct pci_bus *bus, u32 devfn, { struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata); struct mvebu_pcie_port *port; - unsigned long flags; int ret; port = mvebu_pcie_find_port(pcie, bus, devfn); @@ -611,10 +664,8 @@ static int mvebu_pcie_wr_conf(struct pci_bus *bus, u32 devfn, return PCIBIOS_DEVICE_NOT_FOUND; /* Access the real PCIe interface */ - spin_lock_irqsave(&port->conf_lock, flags); ret = mvebu_pcie_hw_wr_conf(port, bus, devfn, where, size, val); - spin_unlock_irqrestore(&port->conf_lock, flags); return ret; } @@ -625,7 +676,6 @@ static int mvebu_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, { struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata); struct mvebu_pcie_port *port; - unsigned long flags; int ret; port = mvebu_pcie_find_port(pcie, bus, devfn); @@ -657,10 +707,8 @@ static int mvebu_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, } /* Access the real PCIe interface */ - spin_lock_irqsave(&port->conf_lock, flags); ret = mvebu_pcie_hw_rd_conf(port, bus, devfn, where, size, val); - spin_unlock_irqrestore(&port->conf_lock, flags); return ret; } @@ -743,14 +791,21 @@ static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev, /* * On the PCI-to-PCI bridge side, the I/O windows must have at - * least a 64 KB size and be aligned on their size, and the - * memory windows must have at least a 1 MB size and be - * aligned on their size + * least a 64 KB size and the memory windows must have at + * least a 1 MB size. Moreover, MBus windows need to have a + * base address aligned on their size, and their size must be + * a power of two. This means that if the BAR doesn't have a + * power of two size, several MBus windows will actually be + * created. We need to ensure that the biggest MBus window + * (which will be the first one) is aligned on its size, which + * explains the rounddown_pow_of_two() being done here. */ if (res->flags & IORESOURCE_IO) - return round_up(start, max_t(resource_size_t, SZ_64K, size)); + return round_up(start, max_t(resource_size_t, SZ_64K, + rounddown_pow_of_two(size))); else if (res->flags & IORESOURCE_MEM) - return round_up(start, max_t(resource_size_t, SZ_1M, size)); + return round_up(start, max_t(resource_size_t, SZ_1M, + rounddown_pow_of_two(size))); else return start; } @@ -1000,7 +1055,6 @@ static int mvebu_pcie_probe(struct platform_device *pdev) mvebu_pcie_set_local_dev_nr(port, 1); port->dn = child; - spin_lock_init(&port->conf_lock); mvebu_sw_pci_bridge_init(port); i++; } diff --git a/drivers/pci/host/pci-tegra.c b/drivers/pci/host/pci-tegra.c index 330f7e3..083cf37 100644 --- a/drivers/pci/host/pci-tegra.c +++ b/drivers/pci/host/pci-tegra.c @@ -639,10 +639,15 @@ static int tegra_pcie_setup(int nr, struct pci_sys_data *sys) static int tegra_pcie_map_irq(const struct pci_dev *pdev, u8 slot, u8 pin) { struct tegra_pcie *pcie = sys_to_pcie(pdev->bus->sysdata); + int irq; tegra_cpuidle_pcie_irqs_in_use(); - return pcie->irq; + irq = of_irq_parse_and_map_pci(pdev, slot, pin); + if (!irq) + irq = pcie->irq; + + return irq; } static void tegra_pcie_add_bus(struct pci_bus *bus) diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c index 77a649d..1eaf4df 100644 --- a/drivers/pci/host/pcie-designware.c +++ b/drivers/pci/host/pcie-designware.c @@ -17,6 +17,7 @@ #include <linux/module.h> #include <linux/msi.h> #include <linux/of_address.h> +#include <linux/of_pci.h> #include <linux/pci.h> #include <linux/pci_regs.h> #include <linux/types.h> @@ -494,7 +495,7 @@ int __init dw_pcie_host_init(struct pcie_port *pp) dw_pci.nr_controllers = 1; dw_pci.private_data = (void **)&pp; - pci_common_init(&dw_pci); + pci_common_init_dev(pp->dev, &dw_pci); pci_assign_unassigned_resources(); #ifdef CONFIG_PCI_DOMAINS dw_pci.domain++; @@ -524,13 +525,13 @@ static void dw_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev) dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1, PCIE_ATU_VIEWPORT); dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_CFG1, PCIE_ATU_CR1); - dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); dw_pcie_writel_rc(pp, pp->cfg1_base, PCIE_ATU_LOWER_BASE); dw_pcie_writel_rc(pp, (pp->cfg1_base >> 32), PCIE_ATU_UPPER_BASE); dw_pcie_writel_rc(pp, pp->cfg1_base + pp->config.cfg1_size - 1, PCIE_ATU_LIMIT); dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET); dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET); + dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); } static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp) @@ -539,7 +540,6 @@ static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp) dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0, PCIE_ATU_VIEWPORT); dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_MEM, PCIE_ATU_CR1); - dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); dw_pcie_writel_rc(pp, pp->mem_base, PCIE_ATU_LOWER_BASE); dw_pcie_writel_rc(pp, (pp->mem_base >> 32), PCIE_ATU_UPPER_BASE); dw_pcie_writel_rc(pp, pp->mem_base + pp->config.mem_size - 1, @@ -547,6 +547,7 @@ static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp) dw_pcie_writel_rc(pp, pp->config.mem_bus_addr, PCIE_ATU_LOWER_TARGET); dw_pcie_writel_rc(pp, upper_32_bits(pp->config.mem_bus_addr), PCIE_ATU_UPPER_TARGET); + dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); } static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp) @@ -555,7 +556,6 @@ static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp) dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1, PCIE_ATU_VIEWPORT); dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_IO, PCIE_ATU_CR1); - dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); dw_pcie_writel_rc(pp, pp->io_base, PCIE_ATU_LOWER_BASE); dw_pcie_writel_rc(pp, (pp->io_base >> 32), PCIE_ATU_UPPER_BASE); dw_pcie_writel_rc(pp, pp->io_base + pp->config.io_size - 1, @@ -563,6 +563,7 @@ static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp) dw_pcie_writel_rc(pp, pp->config.io_bus_addr, PCIE_ATU_LOWER_TARGET); dw_pcie_writel_rc(pp, upper_32_bits(pp->config.io_bus_addr), PCIE_ATU_UPPER_TARGET); + dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2); } static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus, @@ -642,7 +643,6 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, int size, u32 *val) { struct pcie_port *pp = sys_to_pcie(bus->sysdata); - unsigned long flags; int ret; if (!pp) { @@ -655,13 +655,11 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, return PCIBIOS_DEVICE_NOT_FOUND; } - spin_lock_irqsave(&pp->conf_lock, flags); if (bus->number != pp->root_bus_nr) ret = dw_pcie_rd_other_conf(pp, bus, devfn, where, size, val); else ret = dw_pcie_rd_own_conf(pp, where, size, val); - spin_unlock_irqrestore(&pp->conf_lock, flags); return ret; } @@ -670,7 +668,6 @@ static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn, int where, int size, u32 val) { struct pcie_port *pp = sys_to_pcie(bus->sysdata); - unsigned long flags; int ret; if (!pp) { @@ -681,13 +678,11 @@ static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn, if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) return PCIBIOS_DEVICE_NOT_FOUND; - spin_lock_irqsave(&pp->conf_lock, flags); if (bus->number != pp->root_bus_nr) ret = dw_pcie_wr_other_conf(pp, bus, devfn, where, size, val); else ret = dw_pcie_wr_own_conf(pp, where, size, val); - spin_unlock_irqrestore(&pp->conf_lock, flags); return ret; } @@ -727,7 +722,7 @@ static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys) if (pp) { pp->root_bus_nr = sys->busnr; - bus = pci_scan_root_bus(NULL, sys->busnr, &dw_pcie_ops, + bus = pci_scan_root_bus(pp->dev, sys->busnr, &dw_pcie_ops, sys, &sys->resources); } else { bus = NULL; @@ -740,8 +735,13 @@ static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys) static int dw_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) { struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata); + int irq; + + irq = of_irq_parse_and_map_pci(dev, slot, pin); + if (!irq) + irq = pp->irq; - return pp->irq; + return irq; } static void dw_pcie_add_bus(struct pci_bus *bus) @@ -768,7 +768,7 @@ void dw_pcie_setup_rc(struct pcie_port *pp) u32 membase; u32 memlimit; - /* set the number of lines as 4 */ + /* set the number of lanes */ dw_pcie_readl_rc(pp, PCIE_PORT_LINK_CONTROL, &val); val &= ~PORT_LINK_MODE_MASK; switch (pp->lanes) { diff --git a/drivers/pci/host/pcie-designware.h b/drivers/pci/host/pcie-designware.h index a169d22..77f592f 100644 --- a/drivers/pci/host/pcie-designware.h +++ b/drivers/pci/host/pcie-designware.h @@ -41,7 +41,6 @@ struct pcie_port { void __iomem *va_cfg1_base; u64 io_base; u64 mem_base; - spinlock_t conf_lock; struct resource cfg; struct resource io; struct resource mem; |
