diff options
| -rw-r--r-- | Documentation/block/cfq-iosched.txt | 45 | ||||
| -rw-r--r-- | Documentation/cgroups/blkio-controller.txt | 28 |
2 files changed, 73 insertions, 0 deletions
diff --git a/Documentation/block/cfq-iosched.txt b/Documentation/block/cfq-iosched.txt new file mode 100644 index 0000000..e578fee --- /dev/null +++ b/Documentation/block/cfq-iosched.txt @@ -0,0 +1,45 @@ +CFQ ioscheduler tunables +======================== + +slice_idle +---------- +This specifies how long CFQ should idle for next request on certain cfq queues +(for sequential workloads) and service trees (for random workloads) before +queue is expired and CFQ selects next queue to dispatch from. + +By default slice_idle is a non-zero value. That means by default we idle on +queues/service trees. This can be very helpful on highly seeky media like +single spindle SATA/SAS disks where we can cut down on overall number of +seeks and see improved throughput. + +Setting slice_idle to 0 will remove all the idling on queues/service tree +level and one should see an overall improved throughput on faster storage +devices like multiple SATA/SAS disks in hardware RAID configuration. The down +side is that isolation provided from WRITES also goes down and notion of +IO priority becomes weaker. + +So depending on storage and workload, it might be useful to set slice_idle=0. +In general I think for SATA/SAS disks and software RAID of SATA/SAS disks +keeping slice_idle enabled should be useful. For any configurations where +there are multiple spindles behind single LUN (Host based hardware RAID +controller or for storage arrays), setting slice_idle=0 might end up in better +throughput and acceptable latencies. + +CFQ IOPS Mode for group scheduling +=================================== +Basic CFQ design is to provide priority based time slices. Higher priority +process gets bigger time slice and lower priority process gets smaller time +slice. Measuring time becomes harder if storage is fast and supports NCQ and +it would be better to dispatch multiple requests from multiple cfq queues in +request queue at a time. In such scenario, it is not possible to measure time +consumed by single queue accurately. + +What is possible though is to measure number of requests dispatched from a +single queue and also allow dispatch from multiple cfq queue at the same time. +This effectively becomes the fairness in terms of IOPS (IO operations per +second). + +If one sets slice_idle=0 and if storage supports NCQ, CFQ internally switches +to IOPS mode and starts providing fairness in terms of number of requests +dispatched. Note that this mode switching takes effect only for group +scheduling. For non-cgroup users nothing should change. diff --git a/Documentation/cgroups/blkio-controller.txt b/Documentation/cgroups/blkio-controller.txt index 48e0b21..6919d62 100644 --- a/Documentation/cgroups/blkio-controller.txt +++ b/Documentation/cgroups/blkio-controller.txt @@ -217,6 +217,7 @@ Details of cgroup files CFQ sysfs tunable ================= /sys/block/<disk>/queue/iosched/group_isolation +----------------------------------------------- If group_isolation=1, it provides stronger isolation between groups at the expense of throughput. By default group_isolation is 0. In general that @@ -243,6 +244,33 @@ By default one should run with group_isolation=0. If that is not sufficient and one wants stronger isolation between groups, then set group_isolation=1 but this will come at cost of reduced throughput. +/sys/block/<disk>/queue/iosched/slice_idle +------------------------------------------ +On a faster hardware CFQ can be slow, especially with sequential workload. +This happens because CFQ idles on a single queue and single queue might not +drive deeper request queue depths to keep the storage busy. In such scenarios +one can try setting slice_idle=0 and that would switch CFQ to IOPS +(IO operations per second) mode on NCQ supporting hardware. + +That means CFQ will not idle between cfq queues of a cfq group and hence be +able to driver higher queue depth and achieve better throughput. That also +means that cfq provides fairness among groups in terms of IOPS and not in +terms of disk time. + +/sys/block/<disk>/queue/iosched/group_idle +------------------------------------------ +If one disables idling on individual cfq queues and cfq service trees by +setting slice_idle=0, group_idle kicks in. That means CFQ will still idle +on the group in an attempt to provide fairness among groups. + +By default group_idle is same as slice_idle and does not do anything if +slice_idle is enabled. + +One can experience an overall throughput drop if you have created multiple +groups and put applications in that group which are not driving enough +IO to keep disk busy. In that case set group_idle=0, and CFQ will not idle +on individual groups and throughput should improve. + What works ========== - Currently only sync IO queues are support. All the buffered writes are |
