summaryrefslogtreecommitdiffstats
path: root/include
diff options
context:
space:
mode:
authorAlan Stern <stern@rowland.harvard.edu>2010-04-30 16:35:37 -0400
committerGreg Kroah-Hartman <gregkh@suse.de>2010-05-20 13:21:40 -0700
commit85bcb5ee889e0ebb9154718939e049de265fcdfb (patch)
treedaeec28274c8b68fea502c41af84d45d2681ebc5 /include
parent842f16905dfc6743c1dd80c3d29b49ba3ab7f7c8 (diff)
downloadop-kernel-dev-85bcb5ee889e0ebb9154718939e049de265fcdfb.zip
op-kernel-dev-85bcb5ee889e0ebb9154718939e049de265fcdfb.tar.gz
USB: remove URB_NO_SETUP_DMA_MAP
Now that URB_NO_SETUP_DMA_MAP is no longer in use, this patch (as1376) removes all references to it. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Diffstat (limited to 'include')
-rw-r--r--include/linux/usb.h28
1 files changed, 11 insertions, 17 deletions
diff --git a/include/linux/usb.h b/include/linux/usb.h
index a748815..1eb4762 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -953,7 +953,6 @@ extern int usb_disabled(void);
#define URB_ISO_ASAP 0x0002 /* iso-only, urb->start_frame
* ignored */
#define URB_NO_TRANSFER_DMA_MAP 0x0004 /* urb->transfer_dma valid on submit */
-#define URB_NO_SETUP_DMA_MAP 0x0008 /* urb->setup_dma valid on submit */
#define URB_NO_FSBR 0x0020 /* UHCI-specific */
#define URB_ZERO_PACKET 0x0040 /* Finish bulk OUT with short packet */
#define URB_NO_INTERRUPT 0x0080 /* HINT: no non-error interrupt
@@ -1049,12 +1048,8 @@ typedef void (*usb_complete_t)(struct urb *);
* @setup_packet: Only used for control transfers, this points to eight bytes
* of setup data. Control transfers always start by sending this data
* to the device. Then transfer_buffer is read or written, if needed.
- * @setup_dma: For control transfers with URB_NO_SETUP_DMA_MAP set, the
- * device driver has provided this DMA address for the setup packet.
- * The host controller driver should use this in preference to
- * setup_packet, but the HCD may chose to ignore the address if it must
- * copy the setup packet into internal structures. Therefore, setup_packet
- * must always point to a valid buffer.
+ * @setup_dma: DMA pointer for the setup packet. The caller must not use
+ * this field; setup_packet must point to a valid buffer.
* @start_frame: Returns the initial frame for isochronous transfers.
* @number_of_packets: Lists the number of ISO transfer buffers.
* @interval: Specifies the polling interval for interrupt or isochronous
@@ -1086,13 +1081,14 @@ typedef void (*usb_complete_t)(struct urb *);
* bounce buffer or talking to an IOMMU),
* although they're cheap on commodity x86 and ppc hardware.
*
- * Alternatively, drivers may pass the URB_NO_xxx_DMA_MAP transfer flags,
- * which tell the host controller driver that no such mapping is needed since
+ * Alternatively, drivers may pass the URB_NO_TRANSFER_DMA_MAP transfer flag,
+ * which tells the host controller driver that no such mapping is needed for
+ * the transfer_buffer since
* the device driver is DMA-aware. For example, a device driver might
* allocate a DMA buffer with usb_alloc_coherent() or call usb_buffer_map().
- * When these transfer flags are provided, host controller drivers will
- * attempt to use the dma addresses found in the transfer_dma and/or
- * setup_dma fields rather than determining a dma address themselves.
+ * When this transfer flag is provided, host controller drivers will
+ * attempt to use the dma address found in the transfer_dma
+ * field rather than determining a dma address themselves.
*
* Note that transfer_buffer must still be set if the controller
* does not support DMA (as indicated by bus.uses_dma) and when talking
@@ -1115,11 +1111,9 @@ typedef void (*usb_complete_t)(struct urb *);
* should always terminate with a short packet, even if it means adding an
* extra zero length packet.
*
- * Control URBs must provide a setup_packet. The setup_packet and
- * transfer_buffer may each be mapped for DMA or not, independently of
- * the other. The transfer_flags bits URB_NO_TRANSFER_DMA_MAP and
- * URB_NO_SETUP_DMA_MAP indicate which buffers have already been mapped.
- * URB_NO_SETUP_DMA_MAP is ignored for non-control URBs.
+ * Control URBs must provide a valid pointer in the setup_packet field.
+ * Unlike the transfer_buffer, the setup_packet may not be mapped for DMA
+ * beforehand.
*
* Interrupt URBs must provide an interval, saying how often (in milliseconds
* or, for highspeed devices, 125 microsecond units)
OpenPOWER on IntegriCloud