Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

John Linville says:

====================
Here is another batch of updates intended for 3.6.  This includes a
number of pulls, including ones from the mac80211, iwlwifi, ath6kl, and
wl12xx trees.  I also pulled from the wireless tree to avoid potential
build conflicts.  There are a number of other patches applied directly,
including a number for the Broadcom drivers and the mwifiex driver.

The updates cover the usual variety of new hardware support and feature
enhancements.  It's all good work, but there aren't any big headliners.
This does resolve a net-next/wireless-next merge conflict reported
by Stephen.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 74 insertions, 20 deletions

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 7319f25..061c019 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -627,10 +627,10 @@ struct sta_bss_parameters {
  * @llid: mesh local link id
  * @plid: mesh peer link id
  * @plink_state: mesh peer link state
- * @signal: the signal strength, type depends on the wiphy's signal_type
-	NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
- * @signal_avg: avg signal strength, type depends on the wiphy's signal_type
-	NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
+ * @signal: The signal strength, type depends on the wiphy's signal_type.
+ *	For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
+ * @signal_avg: Average signal strength, type depends on the wiphy's signal_type.
+ *	For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
  * @txrate: current unicast bitrate from this station
  * @rxrate: current unicast bitrate to this station
  * @rx_packets: packets received from this station
@@ -790,43 +790,95 @@ struct bss_parameters {
 	int ht_opmode;
 };
 
-/*
+/**
  * struct mesh_config - 802.11s mesh configuration
  *
  * These parameters can be changed while the mesh is active.
+ *
+ * @dot11MeshRetryTimeout: the initial retry timeout in millisecond units used
+ *	by the Mesh Peering Open message
+ * @dot11MeshConfirmTimeout: the initial retry timeout in millisecond units
+ *	used by the Mesh Peering Open message
+ * @dot11MeshHoldingTimeout: the confirm timeout in millisecond units used by
+ *	the mesh peering management to close a mesh peering
+ * @dot11MeshMaxPeerLinks: the maximum number of peer links allowed on this
+ *	mesh interface
+ * @dot11MeshMaxRetries: the maximum number of peer link open retries that can
+ *	be sent to establish a new peer link instance in a mesh
+ * @dot11MeshTTL: the value of TTL field set at a source mesh STA
+ * @element_ttl: the value of TTL field set at a mesh STA for path selection
+ *	elements
+ * @auto_open_plinks: whether we should automatically open peer links when we
+ *	detect compatible mesh peers
+ * @dot11MeshNbrOffsetMaxNeighbor: the maximum number of neighbors to
+ *	synchronize to for 11s default synchronization method
+ * @dot11MeshHWMPmaxPREQretries: the number of action frames containing a PREQ
+ *	that an originator mesh STA can send to a particular path target
+ * @path_refresh_time: how frequently to refresh mesh paths in milliseconds
+ * @min_discovery_timeout: the minimum length of time to wait until giving up on
+ *	a path discovery in milliseconds
+ * @dot11MeshHWMPactivePathTimeout: the time (in TUs) for which mesh STAs
+ *	receiving a PREQ shall consider the forwarding information from the
+ *	root to be valid. (TU = time unit)
+ * @dot11MeshHWMPpreqMinInterval: the minimum interval of time (in TUs) during
+ *	which a mesh STA can send only one action frame containing a PREQ
+ *	element
+ * @dot11MeshHWMPperrMinInterval: the minimum interval of time (in TUs) during
+ *	which a mesh STA can send only one Action frame containing a PERR
+ *	element
+ * @dot11MeshHWMPnetDiameterTraversalTime: the interval of time (in TUs) that
+ *	it takes for an HWMP information element to propagate across the mesh
+ * @dot11MeshHWMPRootMode: the configuration of a mesh STA as root mesh STA
+ * @dot11MeshHWMPRannInterval: the interval of time (in TUs) between root
+ *	announcements are transmitted
+ * @dot11MeshGateAnnouncementProtocol: whether to advertise that this mesh
+ *	station has access to a broader network beyond the MBSS. (This is
+ *	missnamed in draft 12.0: dot11MeshGateAnnouncementProtocol set to true
+ *	only means that the station will announce others it's a mesh gate, but
+ *	not necessarily using the gate announcement protocol. Still keeping the
+ *	same nomenclature to be in sync with the spec)
+ * @dot11MeshForwarding: whether the Mesh STA is forwarding or non-forwarding
+ *	entity (default is TRUE - forwarding entity)
+ * @rssi_threshold: the threshold for average signal strength of candidate
+ *	station to establish a peer link
+ * @ht_opmode: mesh HT protection mode
+ *
+ * @dot11MeshHWMPactivePathToRootTimeout: The time (in TUs) for which mesh STAs
+ *	receiving a proactive PREQ shall consider the forwarding information to
+ *	the root mesh STA to be valid.
+ *
+ * @dot11MeshHWMProotInterval: The interval of time (in TUs) between proactive
+ *	PREQs are transmitted.
+ * @dot11MeshHWMPconfirmationInterval: The minimum interval of time (in TUs)
+ *	during which a mesh STA can send only one Action frame containing
+ *	a PREQ element for root path confirmation.
  */
 struct mesh_config {
-	/* Timeouts in ms */
-	/* Mesh plink management parameters */
 	u16 dot11MeshRetryTimeout;
 	u16 dot11MeshConfirmTimeout;
 	u16 dot11MeshHoldingTimeout;
 	u16 dot11MeshMaxPeerLinks;
-	u8  dot11MeshMaxRetries;
-	u8  dot11MeshTTL;
-	/* ttl used in path selection information elements */
-	u8  element_ttl;
+	u8 dot11MeshMaxRetries;
+	u8 dot11MeshTTL;
+	u8 element_ttl;
 	bool auto_open_plinks;
-	/* neighbor offset synchronization */
 	u32 dot11MeshNbrOffsetMaxNeighbor;
-	/* HWMP parameters */
-	u8  dot11MeshHWMPmaxPREQretries;
+	u8 dot11MeshHWMPmaxPREQretries;
 	u32 path_refresh_time;
 	u16 min_discovery_timeout;
 	u32 dot11MeshHWMPactivePathTimeout;
 	u16 dot11MeshHWMPpreqMinInterval;
 	u16 dot11MeshHWMPperrMinInterval;
 	u16 dot11MeshHWMPnetDiameterTraversalTime;
-	u8  dot11MeshHWMPRootMode;
+	u8 dot11MeshHWMPRootMode;
 	u16 dot11MeshHWMPRannInterval;
-	/* This is missnamed in draft 12.0: dot11MeshGateAnnouncementProtocol
-	 * set to true only means that the station will announce others it's a
-	 * mesh gate, but not necessarily using the gate announcement protocol.
-	 * Still keeping the same nomenclature to be in sync with the spec. */
-	bool  dot11MeshGateAnnouncementProtocol;
+	bool dot11MeshGateAnnouncementProtocol;
 	bool dot11MeshForwarding;
 	s32 rssi_threshold;
 	u16 ht_opmode;
+	u32 dot11MeshHWMPactivePathToRootTimeout;
+	u16 dot11MeshHWMProotInterval;
+	u16 dot11MeshHWMPconfirmationInterval;
 };
 
 /**
@@ -975,6 +1027,7 @@ struct cfg80211_match_set {
  * @wiphy: the wiphy this was for
  * @dev: the interface
  * @channels: channels to scan
+ * @rssi_thold: don't report scan results below this threshold (in s32 dBm)
  */
 struct cfg80211_sched_scan_request {
 	struct cfg80211_ssid *ssids;
@@ -985,6 +1038,7 @@ struct cfg80211_sched_scan_request {
 	size_t ie_len;
 	struct cfg80211_match_set *match_sets;
 	int n_match_sets;
+	s32 rssi_thold;
 
 	/* internal */
 	struct wiphy *wiphy;