Merge branch 'linus' into core/iommu

3 files changed, 75 insertions, 2 deletions

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 8222931..68bb1c5 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -327,9 +327,9 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum);
  * @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped
  * @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped
  * @len: size of rx and tx buffers (in bytes)
- * @speed_hz: Select a speed other then the device default for this
+ * @speed_hz: Select a speed other than the device default for this
  *      transfer. If 0 the default (from @spi_device) is used.
- * @bits_per_word: select a bits_per_word other then the device default
+ * @bits_per_word: select a bits_per_word other than the device default
  *      for this transfer. If 0 the default (from @spi_device) is used.
  * @cs_change: affects chipselect after this transfer completes
  * @delay_usecs: microseconds to delay after this transfer before
diff --git a/include/linux/spi/spi_gpio.h b/include/linux/spi/spi_gpio.h
new file mode 100644
index 0000000..0f01a0f
--- /dev/null
+++ b/include/linux/spi/spi_gpio.h
@@ -0,0 +1,60 @@
+#ifndef __LINUX_SPI_GPIO_H
+#define __LINUX_SPI_GPIO_H
+
+/*
+ * For each bitbanged SPI bus, set up a platform_device node with:
+ *   - name "spi_gpio"
+ *   - id the same as the SPI bus number it implements
+ *   - dev.platform data pointing to a struct spi_gpio_platform_data
+ *
+ * Or, see the driver code for information about speedups that are
+ * possible on platforms that support inlined access for GPIOs (no
+ * spi_gpio_platform_data is used).
+ *
+ * Use spi_board_info with these busses in the usual way, being sure
+ * that the controller_data being the GPIO used for each device's
+ * chipselect:
+ *
+ *	static struct spi_board_info ... [] = {
+ *	...
+ *		// this slave uses GPIO 42 for its chipselect
+ *		.controller_data = (void *) 42,
+ *	...
+ *		// this one uses GPIO 86 for its chipselect
+ *		.controller_data = (void *) 86,
+ *	...
+ *	};
+ *
+ * If the bitbanged bus is later switched to a "native" controller,
+ * that platform_device and controller_data should be removed.
+ */
+
+/**
+ * struct spi_gpio_platform_data - parameter for bitbanged SPI master
+ * @sck: number of the GPIO used for clock output
+ * @mosi: number of the GPIO used for Master Output, Slave In (MOSI) data
+ * @miso: number of the GPIO used for Master Input, Slave Output (MISO) data
+ * @num_chipselect: how many slaves to allow
+ *
+ * All GPIO signals used with the SPI bus managed through this driver
+ * (chipselects, MOSI, MISO, SCK) must be configured as GPIOs, instead
+ * of some alternate function.
+ *
+ * It can be convenient to use this driver with pins that have alternate
+ * functions associated with a "native" SPI controller if a driver for that
+ * controller is not available, or is missing important functionality.
+ *
+ * On platforms which can do so, configure MISO with a weak pullup unless
+ * there's an external pullup on that signal.  That saves power by avoiding
+ * floating signals.  (A weak pulldown would save power too, but many
+ * drivers expect to see all-ones data as the no slave "response".)
+ */
+struct spi_gpio_platform_data {
+	unsigned	sck;
+	unsigned	mosi;
+	unsigned	miso;
+
+	u16		num_chipselect;
+};
+
+#endif /* __LINUX_SPI_GPIO_H */
diff --git a/include/linux/spi/tdo24m.h b/include/linux/spi/tdo24m.h
new file mode 100644
index 0000000..7572d4e
--- /dev/null
+++ b/include/linux/spi/tdo24m.h
@@ -0,0 +1,13 @@
+#ifndef __TDO24M_H__
+#define __TDO24M_H__
+
+enum tdo24m_model {
+	TDO24M,
+	TDO35S,
+};
+
+struct tdo24m_platform_data {
+	enum tdo24m_model model;
+};
+
+#endif /* __TDO24M_H__ */