libata: consistently use msecs for time durations

libata has been using mix of jiffies and msecs for time druations.
This is getting confusing.  As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs.  So, durations are in msecs and
deadlines are in jiffies.  ata_deadline() is added to compute deadline
from a start time and duration in msecs.

While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

1 files changed, 16 insertions, 10 deletions

diff --git a/include/linux/libata.h b/include/linux/libata.h
index e57e5d0..94110b6 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -27,6 +27,7 @@
 #define __LINUX_LIBATA_H__
 
 #include <linux/delay.h>
+#include <linux/jiffies.h>
 #include <linux/interrupt.h>
 #include <linux/dma-mapping.h>
 #include <linux/scatterlist.h>
@@ -115,7 +116,7 @@ enum {
 	/* tag ATA_MAX_QUEUE - 1 is reserved for internal commands */
 	ATA_MAX_QUEUE		= 32,
 	ATA_TAG_INTERNAL	= ATA_MAX_QUEUE - 1,
-	ATA_SHORT_PAUSE		= (HZ >> 6) + 1,
+	ATA_SHORT_PAUSE		= 16,
 
 	ATAPI_MAX_DRAIN		= 16 << 10,
 
@@ -234,17 +235,17 @@ enum {
 	/* bits 24:31 of host->flags are reserved for LLD specific flags */
 
 	/* various lengths of time */
-	ATA_TMOUT_BOOT		= 30 * HZ,	/* heuristic */
-	ATA_TMOUT_BOOT_QUICK	= 7 * HZ,	/* heuristic */
-	ATA_TMOUT_INTERNAL	= 30 * HZ,
-	ATA_TMOUT_INTERNAL_QUICK = 5 * HZ,
+	ATA_TMOUT_BOOT		= 30000,	/* heuristic */
+	ATA_TMOUT_BOOT_QUICK	=  7000,	/* heuristic */
+	ATA_TMOUT_INTERNAL	= 30000,
+	ATA_TMOUT_INTERNAL_QUICK = 5000,
 
 	/* FIXME: GoVault needs 2s but we can't afford that without
 	 * parallel probing.  800ms is enough for iVDR disk
 	 * HHD424020F7SV00.  Increase to 2secs when parallel probing
 	 * is in place.
 	 */
-	ATA_TMOUT_FF_WAIT	= 4 * HZ / 5,
+	ATA_TMOUT_FF_WAIT	=  800,
 
 	/* Spec mandates to wait for ">= 2ms" before checking status
 	 * after reset.  We wait 150ms, because that was the magic
@@ -256,14 +257,14 @@ enum {
 	 *
 	 * Old drivers/ide uses the 2mS rule and then waits for ready.
 	 */
-	ATA_WAIT_AFTER_RESET_MSECS = 150,
+	ATA_WAIT_AFTER_RESET	=  150,
 
 	/* If PMP is supported, we have to do follow-up SRST.  As some
 	 * PMPs don't send D2H Reg FIS after hardreset, LLDs are
 	 * advised to wait only for the following duration before
 	 * doing SRST.
 	 */
-	ATA_TMOUT_PMP_SRST_WAIT	= 1 * HZ,
+	ATA_TMOUT_PMP_SRST_WAIT	= 1000,
 
 	/* ATA bus states */
 	BUS_UNKNOWN		= 0,
@@ -895,8 +896,7 @@ extern void ata_host_resume(struct ata_host *host);
 #endif
 extern int ata_ratelimit(void);
 extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
-			     unsigned long interval_msec,
-			     unsigned long timeout_msec);
+			     unsigned long interval, unsigned long timeout);
 extern int atapi_cmd_type(u8 opcode);
 extern void ata_tf_to_fis(const struct ata_taskfile *tf,
 			  u8 pmp, int is_cmd, u8 *fis);
@@ -1389,6 +1389,12 @@ static inline int ata_check_ready(u8 status)
 	return 0;
 }
 
+static inline unsigned long ata_deadline(unsigned long from_jiffies,
+					 unsigned long timeout_msecs)
+{
+	return from_jiffies + msecs_to_jiffies(timeout_msecs);
+}
+
 
 /**************************************************************************
  * PMP - drivers/ata/libata-pmp.c