Merge master.kernel.org:/home/rmk/linux-2.6-arm

22 files changed, 16 insertions, 2047 deletions

diff --git a/drivers/amba/bus.c b/drivers/amba/bus.c
index 1bbdd16..889855d 100644
--- a/drivers/amba/bus.c
+++ b/drivers/amba/bus.c
@@ -15,7 +15,6 @@
 #include <linux/amba/bus.h>
 
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/sizes.h>
 
 #define to_amba_device(d)	container_of(d, struct amba_device, dev)
diff --git a/drivers/input/serio/sa1111ps2.c b/drivers/input/serio/sa1111ps2.c
index 3f0df33..ebd9976 100644
--- a/drivers/input/serio/sa1111ps2.c
+++ b/drivers/input/serio/sa1111ps2.c
@@ -20,7 +20,6 @@
 #include <linux/spinlock.h>
 
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/system.h>
 
 #include <asm/hardware/sa1111.h>
diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index b9b77cf..7abd7fe 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -473,14 +473,6 @@ config MTD_IXP2000
 	  IXDP425 and Coyote. If you have an IXP2000 based board and
 	  would like to use the flash chips on it, say 'Y'.
 
-config MTD_EPXA10DB
-	tristate "CFI Flash device mapped on Epxa10db"
-	depends on MTD_CFI && MTD_PARTITIONS && ARCH_CAMELOT
-	help
-	  This enables support for the flash devices on the Altera
-	  Excalibur XA10 Development Board. If you are building a kernel
-	  for on of these boards then you should say 'Y' otherwise say 'N'.
-
 config MTD_FORTUNET
 	tristate "CFI Flash device mapped on the FortuNet board"
 	depends on MTD_CFI && MTD_PARTITIONS && SA1100_FORTUNET
diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile
index 2f7e254..ab71f17 100644
--- a/drivers/mtd/maps/Makefile
+++ b/drivers/mtd/maps/Makefile
@@ -15,7 +15,6 @@ obj-$(CONFIG_MTD_CFI_FLAGADM)	+= cfi_flagadm.o
 obj-$(CONFIG_MTD_CSTM_MIPS_IXX)	+= cstm_mips_ixx.o
 obj-$(CONFIG_MTD_DC21285)	+= dc21285.o
 obj-$(CONFIG_MTD_DILNETPC)	+= dilnetpc.o
-obj-$(CONFIG_MTD_EPXA10DB)	+= epxa10db-flash.o
 obj-$(CONFIG_MTD_IQ80310)	+= iq80310.o
 obj-$(CONFIG_MTD_L440GX)	+= l440gx.o
 obj-$(CONFIG_MTD_AMD76XROM)	+= amd76xrom.o
diff --git a/drivers/mtd/maps/epxa10db-flash.c b/drivers/mtd/maps/epxa10db-flash.c
deleted file mode 100644
index 265b079..0000000
--- a/drivers/mtd/maps/epxa10db-flash.c
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * Flash memory access on EPXA based devices
- *
- * (C) 2000 Nicolas Pitre <nico@cam.org>
- *  Copyright (C) 2001 Altera Corporation
- *  Copyright (C) 2001 Red Hat, Inc.
- *
- * $Id: epxa10db-flash.c,v 1.15 2005/11/07 11:14:27 gleixner Exp $
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-
-#include <asm/io.h>
-#include <asm/hardware.h>
-
-#ifdef CONFIG_EPXA10DB
-#define BOARD_NAME "EPXA10DB"
-#else
-#define BOARD_NAME "EPXA1DB"
-#endif
-
-static int nr_parts = 0;
-static struct mtd_partition *parts;
-
-static struct mtd_info *mymtd;
-
-static int epxa_default_partitions(struct mtd_info *master, struct mtd_partition **pparts);
-
-
-static struct map_info epxa_map = {
-	.name =		"EPXA flash",
-	.size =		FLASH_SIZE,
-	.bankwidth =	2,
-	.phys =		FLASH_START,
-};
-
-static const char *probes[] = { "RedBoot", "afs", NULL };
-
-static int __init epxa_mtd_init(void)
-{
-	int i;
-
-	printk(KERN_NOTICE "%s flash device: 0x%x at 0x%x\n", BOARD_NAME, FLASH_SIZE, FLASH_START);
-
-	epxa_map.virt = ioremap(FLASH_START, FLASH_SIZE);
-	if (!epxa_map.virt) {
-		printk("Failed to ioremap %s flash\n",BOARD_NAME);
-		return -EIO;
-	}
-	simple_map_init(&epxa_map);
-
-	mymtd = do_map_probe("cfi_probe", &epxa_map);
-	if (!mymtd) {
-		iounmap((void *)epxa_map.virt);
-		return -ENXIO;
-	}
-
-	mymtd->owner = THIS_MODULE;
-
-	/* Unlock the flash device. */
-	if(mymtd->unlock){
-		for (i=0; i<mymtd->numeraseregions;i++){
-			int j;
-			for(j=0;j<mymtd->eraseregions[i].numblocks;j++){
-				mymtd->unlock(mymtd,mymtd->eraseregions[i].offset + j * mymtd->eraseregions[i].erasesize,mymtd->eraseregions[i].erasesize);
-			}
-		}
-	}
-
-#ifdef CONFIG_MTD_PARTITIONS
-	nr_parts = parse_mtd_partitions(mymtd, probes, &parts, 0);
-
-	if (nr_parts > 0) {
-		add_mtd_partitions(mymtd, parts, nr_parts);
-		return 0;
-	}
-#endif
-	/* No recognised partitioning schemes found - use defaults */
-	nr_parts = epxa_default_partitions(mymtd, &parts);
-	if (nr_parts > 0) {
-		add_mtd_partitions(mymtd, parts, nr_parts);
-		return 0;
-	}
-
-	/* If all else fails... */
-	add_mtd_device(mymtd);
-	return 0;
-}
-
-static void __exit epxa_mtd_cleanup(void)
-{
-	if (mymtd) {
-		if (nr_parts)
-			del_mtd_partitions(mymtd);
-		else
-			del_mtd_device(mymtd);
-		map_destroy(mymtd);
-	}
-	if (epxa_map.virt) {
-		iounmap((void *)epxa_map.virt);
-		epxa_map.virt = 0;
-	}
-}
-
-
-/*
- * This will do for now, once we decide which bootldr we're finally
- * going to use then we'll remove this function and do it properly
- *
- * Partions are currently (as offsets from base of flash):
- * 0x00000000 - 0x003FFFFF - bootloader (!)
- * 0x00400000 - 0x00FFFFFF - Flashdisk
- */
-
-static int __init epxa_default_partitions(struct mtd_info *master, struct mtd_partition **pparts)
-{
-	struct mtd_partition *parts;
-	int ret, i;
-	int npartitions = 0;
-	char *names;
-	const char *name = "jffs";
-
-	printk("Using default partitions for %s\n",BOARD_NAME);
-	npartitions=1;
-	parts = kmalloc(npartitions*sizeof(*parts)+strlen(name), GFP_KERNEL);
-	memzero(parts,npartitions*sizeof(*parts)+strlen(name));
-	if (!parts) {
-		ret = -ENOMEM;
-		goto out;
-	}
-	i=0;
-	names = (char *)&parts[npartitions];
-	parts[i].name = names;
-	names += strlen(name) + 1;
-	strcpy(parts[i].name, name);
-
-#ifdef CONFIG_EPXA10DB
-	parts[i].size = FLASH_SIZE-0x00400000;
-	parts[i].offset = 0x00400000;
-#else
-	parts[i].size = FLASH_SIZE-0x00180000;
-	parts[i].offset = 0x00180000;
-#endif
-
- out:
-	*pparts = parts;
-	return npartitions;
-}
-
-
-module_init(epxa_mtd_init);
-module_exit(epxa_mtd_cleanup);
-
-MODULE_AUTHOR("Clive Davies");
-MODULE_DESCRIPTION("Altera epxa mtd flash map");
-MODULE_LICENSE("GPL");
diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig
index 470364d..625184b 100644
--- a/drivers/net/arm/Kconfig
+++ b/drivers/net/arm/Kconfig
@@ -31,16 +31,3 @@ config ARM_ETHERH
 	help
 	  If you have an Acorn system with one of these network cards, you
 	  should say Y to this option if you wish to use it with Linux.
-
-config ARM_ETHER00
-	tristate "Altera Ether00 support"
-	depends on NET_ETHERNET && ARM && ARCH_CAMELOT
-	help
-	  This is the driver for Altera's ether00 ethernet mac IP core. Say
-	  Y here if you want to build support for this into the kernel. It
-	  is also available as a module (say M here) that can be inserted/
-	  removed from the kernel at the same time as the PLD is configured.
-	  If this driver is running on an epxa10 development board then it
-	  will generate a suitable hw address based on the board serial
-	  number (MTD support is required for this). Otherwise you will
-	  need to set a suitable hw address using ifconfig.
diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile
index b0d7068..bc263ed 100644
--- a/drivers/net/arm/Makefile
+++ b/drivers/net/arm/Makefile
@@ -4,7 +4,6 @@
 #
 
 obj-$(CONFIG_ARM_AM79C961A)	+= am79c961a.o
-obj-$(CONFIG_ARM_ETHER00)	+= ether00.o
 obj-$(CONFIG_ARM_ETHERH)	+= etherh.o
 obj-$(CONFIG_ARM_ETHER3)	+= ether3.o
 obj-$(CONFIG_ARM_ETHER1)	+= ether1.o
diff --git a/drivers/net/arm/am79c961a.c b/drivers/net/arm/am79c961a.c
index 877891a..53e3afc 100644
--- a/drivers/net/arm/am79c961a.c
+++ b/drivers/net/arm/am79c961a.c
@@ -668,9 +668,8 @@ static void __init am79c961_banner(void)
 		printk(KERN_INFO "%s", version);
 }
 
-static int __init am79c961_probe(struct device *_dev)
+static int __init am79c961_probe(struct platform_device *pdev)
 {
-	struct platform_device *pdev = to_platform_device(_dev);
 	struct resource *res;
 	struct net_device *dev;
 	struct dev_priv *priv;
@@ -758,15 +757,16 @@ out:
 	return ret;
 }
 
-static struct device_driver am79c961_driver = {
-	.name		= "am79c961",
-	.bus		= &platform_bus_type,
+static struct platform_driver am79c961_driver = {
 	.probe		= am79c961_probe,
+	.driver		= {
+		.name	= "am79c961",
+	},
 };
 
 static int __init am79c961_init(void)
 {
-	return driver_register(&am79c961_driver);
+	return platform_driver_register(&am79c961_driver);
 }
 
 __initcall(am79c961_init);
diff --git a/drivers/net/arm/ether00.c b/drivers/net/arm/ether00.c
deleted file mode 100644
index 4f1f4e3..0000000
--- a/drivers/net/arm/ether00.c
+++ /dev/null
@@ -1,1017 +0,0 @@
-/*
- *  drivers/net/ether00.c
- *
- *  Copyright (C) 2001 Altera Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-/* includes */
-#include <linux/config.h>
-#include <linux/pci.h>
-#include <linux/sched.h>
-#include <linux/netdevice.h>
-#include <linux/skbuff.h>
-#include <linux/etherdevice.h>
-#include <linux/module.h>
-#include <linux/tqueue.h>
-#include <linux/mtd/mtd.h>
-#include <linux/pld/pld_hotswap.h>
-#include <asm/arch/excalibur.h>
-#include <asm/arch/hardware.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <asm/sizes.h>
-
-#include <asm/arch/ether00.h>
-#include <asm/arch/tdkphy.h>
-
-
-MODULE_AUTHOR("Clive Davies");
-MODULE_DESCRIPTION("Altera Ether00 IP core driver");
-MODULE_LICENSE("GPL");
-
-#define PKT_BUF_SZ 1540 /* Size of each rx buffer */
-#define ETH_NR 4 /* Number of MACs this driver supports */
-
-#define DEBUG(x)
-
-#define __dma_va(x) (unsigned int)((unsigned int)priv->dma_data+(((unsigned int)(x))&(EXC_SPSRAM_BLOCK0_SIZE-1)))
-#define __dma_pa(x) (unsigned int)(EXC_SPSRAM_BLOCK0_BASE+(((unsigned int)(x))-(unsigned int)priv->dma_data))
-
-#define ETHER00_BASE	0
-#define	ETHER00_TYPE
-#define ETHER00_NAME "ether00"
-#define MAC_REG_SIZE 0x400 /* size of MAC register area */
-
-
-
-/* typedefs */
-
-/* The definition of the driver control structure */
-
-#define RX_NUM_BUFF     10
-#define RX_NUM_FDESC    10
-#define TX_NUM_FDESC    10
-
-struct tx_fda_ent{
-	FDA_DESC  fd;
-	BUF_DESC  bd;
-	BUF_DESC  pad;
-};
-struct rx_fda_ent{
-	FDA_DESC  fd;
-	BUF_DESC  bd;
-	BUF_DESC  pad;
-};
-struct rx_blist_ent{
-	FDA_DESC  fd;
-	BUF_DESC  bd;
-	BUF_DESC  pad;
-};
-struct net_priv
-{
-	struct net_device_stats stats;
-	struct sk_buff* skb;
-	void* dma_data;
-	struct rx_blist_ent*  rx_blist_vp;
-	struct rx_fda_ent* rx_fda_ptr;
-	struct tx_fda_ent* tx_fdalist_vp;
-	struct tq_struct  tq_memupdate;
-	unsigned char   memupdate_scheduled;
-	unsigned char   rx_disabled;
-	unsigned char   queue_stopped;
-	spinlock_t rx_lock;
-};
-
-static const char vendor_id[2]={0x07,0xed};
-
-#ifdef ETHER00_DEBUG
-
-/* Dump (most) registers for debugging puposes */
-
-static void dump_regs(struct net_device *dev){
-	struct net_priv* priv=dev->priv;
-	unsigned int* i;
-
-	printk("\n RX free descriptor area:\n");
-
-	for(i=(unsigned int*)priv->rx_fda_ptr;
-	    i<((unsigned int*)(priv->rx_fda_ptr+RX_NUM_FDESC));){
-		printk("%#8x %#8x %#8x %#8x\n",*i,*(i+1),*(i+2),*(i+3));
-		i+=4;
-	}
-
-	printk("\n RX buffer list:\n");
-
-	for(i=(unsigned int*)priv->rx_blist_vp;
-	    i<((unsigned int*)(priv->rx_blist_vp+RX_NUM_BUFF));){
-		printk("%#8x %#8x %#8x %#8x\n",*i,*(i+1),*(i+2),*(i+3));
-		i+=4;
-	}
-
-	printk("\n TX frame descriptor list:\n");
-
-	for(i=(unsigned int*)priv->tx_fdalist_vp;
-	    i<((unsigned int*)(priv->tx_fdalist_vp+TX_NUM_FDESC));){
-		printk("%#8x %#8x %#8x %#8x\n",*i,*(i+1),*(i+2),*(i+3));
-		i+=4;
-	}
-
-	printk("\ndma ctl=%#x\n",readw(ETHER_DMA_CTL(dev->base_addr)));
-	printk("txfrmptr=%#x\n",readw(ETHER_TXFRMPTR(dev->base_addr)));
-	printk("txthrsh=%#x\n",readw(ETHER_TXTHRSH(dev->base_addr)));
-	printk("txpollctr=%#x\n",readw(ETHER_TXPOLLCTR(dev->base_addr)));
-	printk("blfrmptr=%#x\n",readw(ETHER_BLFRMPTR(dev->base_addr)));
-	printk("rxfragsize=%#x\n",readw(ETHER_RXFRAGSIZE(dev->base_addr)));
-	printk("tx_int_en=%#x\n",readw(ETHER_INT_EN(dev->base_addr)));
-	printk("fda_bas=%#x\n",readw(ETHER_FDA_BAS(dev->base_addr)));
-	printk("fda_lim=%#x\n",readw(ETHER_FDA_LIM(dev->base_addr)));
-	printk("int_src=%#x\n",readw(ETHER_INT_SRC(dev->base_addr)));
-	printk("pausecnt=%#x\n",readw(ETHER_PAUSECNT(dev->base_addr)));
-	printk("rempaucnt=%#x\n",readw(ETHER_REMPAUCNT(dev->base_addr)));
-	printk("txconfrmstat=%#x\n",readw(ETHER_TXCONFRMSTAT(dev->base_addr)));
-	printk("mac_ctl=%#x\n",readw(ETHER_MAC_CTL(dev->base_addr)));
-	printk("arc_ctl=%#x\n",readw(ETHER_ARC_CTL(dev->base_addr)));
-	printk("tx_ctl=%#x\n",readw(ETHER_TX_CTL(dev->base_addr)));
-}
-#endif /* ETHER00_DEBUG */
-
-
-static int ether00_write_phy(struct net_device *dev, short address, short value)
-{
-	volatile int count = 1024;
-	writew(value,ETHER_MD_DATA(dev->base_addr));
-	writew( ETHER_MD_CA_BUSY_MSK |
-		ETHER_MD_CA_WR_MSK |
-		(address & ETHER_MD_CA_ADDR_MSK),
-		ETHER_MD_CA(dev->base_addr));
-
-	/* Wait for the command to complete */
-	while((readw(ETHER_MD_CA(dev->base_addr)) & ETHER_MD_CA_BUSY_MSK)&&count){
-		count--;
-	}
-	if (!count){
-		printk("Write to phy failed, addr=%#x, data=%#x\n",address, value);
-		return -EIO;
-	}
-	return 0;
-}
-
-static int ether00_read_phy(struct net_device *dev, short address)
-{
-	volatile int count = 1024;
-	writew( ETHER_MD_CA_BUSY_MSK |
-		(address & ETHER_MD_CA_ADDR_MSK),
-		ETHER_MD_CA(dev->base_addr));
-
-	/* Wait for the command to complete */
-	while((readw(ETHER_MD_CA(dev->base_addr)) & ETHER_MD_CA_BUSY_MSK)&&count){
-		count--;
-	}
-	if (!count){
-		printk(KERN_WARNING "Read from phy timed out\n");
-		return -EIO;
-	}
-	return readw(ETHER_MD_DATA(dev->base_addr));
-}
-
-static void ether00_phy_int(int irq_num, void* dev_id, struct pt_regs* regs)
-{
-	struct net_device* dev=dev_id;
-	int irq_status;
-
-	irq_status=ether00_read_phy(dev, PHY_IRQ_CONTROL);
-
-	if(irq_status & PHY_IRQ_CONTROL_ANEG_COMP_INT_MSK){
-		/*
-		 * Autonegotiation complete on epxa10db. The mac doesn't
-		 * twig if we're in full duplex so we need to check the
-		 * phy status register and configure the mac accordingly
-		 */
-		if(ether00_read_phy(dev, PHY_STATUS)&(PHY_STATUS_10T_F_MSK|PHY_STATUS_100_X_F_MSK)){
-			int tmp;
-			tmp=readl(ETHER_MAC_CTL(dev->base_addr));
-			writel(tmp|ETHER_MAC_CTL_FULLDUP_MSK,ETHER_MAC_CTL(dev->base_addr));
-		}
-	}
-
-	if(irq_status&PHY_IRQ_CONTROL_LS_CHG_INT_MSK){
-
-		if(ether00_read_phy(dev, PHY_STATUS)& PHY_STATUS_LINK_MSK){
-			/* Link is up */
-			netif_carrier_on(dev);
-			//printk("Carrier on\n");
-		}else{
-			netif_carrier_off(dev);
-			//printk("Carrier off\n");
-
-		}
-	}
-
-}
-
-static void setup_blist_entry(struct sk_buff* skb,struct rx_blist_ent* blist_ent_ptr){
-	/* Make the buffer consistent with the cache as the mac is going to write
-	 * directly into it*/
-	blist_ent_ptr->fd.FDSystem=(unsigned int)skb;
-	blist_ent_ptr->bd.BuffData=(char*)__pa(skb->data);
-	consistent_sync(skb->data,PKT_BUF_SZ,PCI_DMA_FROMDEVICE);
-        /* align IP on 16 Byte (DMA_CTL set to skip 2 bytes) */
-	skb_reserve(skb,2);
-	blist_ent_ptr->bd.BuffLength=PKT_BUF_SZ-2;
-	blist_ent_ptr->fd.FDLength=1;
-	blist_ent_ptr->fd.FDCtl=FDCTL_COWNSFD_MSK;
-	blist_ent_ptr->bd.BDCtl=BDCTL_COWNSBD_MSK;
-}
-
-
-static int ether00_mem_init(struct net_device* dev)
-{
-	struct net_priv* priv=dev->priv;
-	struct tx_fda_ent *tx_fd_ptr,*tx_end_ptr;
-	struct rx_blist_ent* blist_ent_ptr;
-	int i;
-
-	/*
-	 * Grab a block of on chip SRAM to contain the control stuctures for
-	 * the ethernet MAC. This uncached becuase it needs to be accesses by both
-	 * bus masters (cpu + mac). However, it shouldn't matter too much in terms
-	 * of speed as its on chip memory
-	 */
-	priv->dma_data=ioremap_nocache(EXC_SPSRAM_BLOCK0_BASE,EXC_SPSRAM_BLOCK0_SIZE );
-	if (!priv->dma_data)
-		return -ENOMEM;
-
-	priv->rx_fda_ptr=(struct rx_fda_ent*)priv->dma_data;
-	/*
-	 * Now share it out amongst the Frame descriptors and the buffer list
-	 */
-	priv->rx_blist_vp=(struct rx_blist_ent*)((unsigned int)priv->dma_data+RX_NUM_FDESC*sizeof(struct rx_fda_ent));
-
-	/*
-	 *Initalise the FDA list
-	 */
-	/* set ownership to the controller */
-	memset(priv->rx_fda_ptr,0x80,RX_NUM_FDESC*sizeof(struct rx_fda_ent));
-
-	/*
-	 *Initialise the buffer list
-	 */
-	blist_ent_ptr=priv->rx_blist_vp;
-	i=0;
-	while(blist_ent_ptr<(priv->rx_blist_vp+RX_NUM_BUFF)){
-		struct sk_buff *skb;
-		blist_ent_ptr->fd.FDLength=1;
-		skb=dev_alloc_skb(PKT_BUF_SZ);
-		if(skb){
-			setup_blist_entry(skb,blist_ent_ptr);
-			blist_ent_ptr->fd.FDNext=(FDA_DESC*)__dma_pa(blist_ent_ptr+1);
-			blist_ent_ptr->bd.BDStat=i++;
-			blist_ent_ptr++;
-		}
-		else
-		{
-			printk("Failed to initalise buffer list\n");
-		}
-
-	}
-	blist_ent_ptr--;
-	blist_ent_ptr->fd.FDNext=(FDA_DESC*)__dma_pa(priv->rx_blist_vp);
-
-	priv->tx_fdalist_vp=(struct tx_fda_ent*)(priv->rx_blist_vp+RX_NUM_BUFF);
-
-	/* Initialise the buffers to be a circular list. The mac will then go poll
-	 * the list until it finds a frame ready to transmit */
-	tx_end_ptr=priv->tx_fdalist_vp+TX_NUM_FDESC;
-	for(tx_fd_ptr=priv->tx_fdalist_vp;tx_fd_ptr<tx_end_ptr;tx_fd_ptr++){
-		tx_fd_ptr->fd.FDNext=(FDA_DESC*)__dma_pa((tx_fd_ptr+1));
-		tx_fd_ptr->fd.FDCtl=1;
-		tx_fd_ptr->fd.FDStat=0;
-		tx_fd_ptr->fd.FDLength=1;
-
-	}
-	/* Change the last FDNext pointer to make a circular list */
-	tx_fd_ptr--;
-	tx_fd_ptr->fd.FDNext=(FDA_DESC*)__dma_pa(priv->tx_fdalist_vp);
-
-	/* Point the device at the chain of Rx and Tx Buffers */
-	writel((unsigned int)__dma_pa(priv->rx_fda_ptr),ETHER_FDA_BAS(dev->base_addr));
-	writel((RX_NUM_FDESC-1)*sizeof(struct rx_fda_ent),ETHER_FDA_LIM(dev->base_addr));
-	writel((unsigned int)__dma_pa(priv->rx_blist_vp),ETHER_BLFRMPTR(dev->base_addr));
-
-	writel((unsigned int)__dma_pa(priv->tx_fdalist_vp),ETHER_TXFRMPTR(dev->base_addr));
-
-	return 0;
-}
-
-
-void ether00_mem_update(void* dev_id)
-{
-	struct net_device* dev=dev_id;
-	struct net_priv* priv=dev->priv;
-	struct sk_buff* skb;
-	struct tx_fda_ent *fda_ptr=priv->tx_fdalist_vp;
-	struct rx_blist_ent* blist_ent_ptr;
-	unsigned long flags;
-
-	priv->tq_memupdate.sync=0;
-	//priv->tq_memupdate.list=
-	priv->memupdate_scheduled=0;
-
-	/* Transmit interrupt */
-	while(fda_ptr<(priv->tx_fdalist_vp+TX_NUM_FDESC)){
-		if(!(FDCTL_COWNSFD_MSK&fda_ptr->fd.FDCtl) && (ETHER_TX_STAT_COMP_MSK&fda_ptr->fd.FDStat)){
-			priv->stats.tx_packets++;
-			priv->stats.tx_bytes+=fda_ptr->bd.BuffLength;
-			skb=(struct sk_buff*)fda_ptr->fd.FDSystem;
-			//printk("%d:txcln:fda=%#x skb=%#x\n",jiffies,fda_ptr,skb);
-			dev_kfree_skb(skb);
-			fda_ptr->fd.FDSystem=0;
-			fda_ptr->fd.FDStat=0;
-			fda_ptr->fd.FDCtl=0;
-		}
-		fda_ptr++;
-	}
-	/* Fill in any missing buffers from the received queue */
-	spin_lock_irqsave(&priv->rx_lock,flags);
-	blist_ent_ptr=priv->rx_blist_vp;
-	while(blist_ent_ptr<(priv->rx_blist_vp+RX_NUM_BUFF)){
-		/* fd.FDSystem of 0 indicates we failed to allocate the buffer in the ISR */
-		if(!blist_ent_ptr->fd.FDSystem){
-			struct sk_buff *skb;
-			skb=dev_alloc_skb(PKT_BUF_SZ);
-			blist_ent_ptr->fd.FDSystem=(unsigned int)skb;
-			if(skb){
-				setup_blist_entry(skb,blist_ent_ptr);
-			}
-			else
-			{
-				break;
-			}
-		}
-		blist_ent_ptr++;
-	}
-	spin_unlock_irqrestore(&priv->rx_lock,flags);
-	if(priv->queue_stopped){
-		//printk("%d:cln:start q\n",jiffies);
-		netif_start_queue(dev);
-	}
-	if(priv->rx_disabled){
-		//printk("%d:enable_irq\n",jiffies);
-		priv->rx_disabled=0;
-		writel(ETHER_RX_CTL_RXEN_MSK,ETHER_RX_CTL(dev->base_addr));
-
-	}
-}
-
-
-static void ether00_int( int irq_num, void* dev_id, struct pt_regs* regs)
-{
-	struct net_device* dev=dev_id;
-	struct net_priv* priv=dev->priv;
-
-	unsigned int   interruptValue;
-
-	interruptValue=readl(ETHER_INT_SRC(dev->base_addr));
-
-	//printk("INT_SRC=%x\n",interruptValue);
-
-	if(!(readl(ETHER_INT_SRC(dev->base_addr)) & ETHER_INT_SRC_IRQ_MSK))
-	{
-		return;		/* Interrupt wasn't caused by us!! */
-	}
-
-	if(readl(ETHER_INT_SRC(dev->base_addr))&
-	   (ETHER_INT_SRC_INTMACRX_MSK |
-	    ETHER_INT_SRC_FDAEX_MSK |
-	    ETHER_INT_SRC_BLEX_MSK)) {
-		struct rx_blist_ent* blist_ent_ptr;
-		struct rx_fda_ent* fda_ent_ptr;
-		struct sk_buff* skb;
-
-		fda_ent_ptr=priv->rx_fda_ptr;
-		spin_lock(&priv->rx_lock);
-		while(fda_ent_ptr<(priv->rx_fda_ptr+RX_NUM_FDESC)){
-			int result;
-
-			if(!(fda_ent_ptr->fd.FDCtl&FDCTL_COWNSFD_MSK))
-			{
-				/* This frame is ready for processing */
-				/*find the corresponding buffer in the bufferlist */
-				blist_ent_ptr=priv->rx_blist_vp+fda_ent_ptr->bd.BDStat;
-				skb=(struct sk_buff*)blist_ent_ptr->fd.FDSystem;
-
-				/* Pass this skb up the stack */
-				skb->dev=dev;
-				skb_put(skb,fda_ent_ptr->fd.FDLength);
-				skb->protocol=eth_type_trans(skb,dev);
-				skb->ip_summed=CHECKSUM_UNNECESSARY;
-				result=netif_rx(skb);
-				/* Update statistics */
-				priv->stats.rx_packets++;
-				priv->stats.rx_bytes+=fda_ent_ptr->fd.FDLength;
-
-				/* Free the FDA entry */
-				fda_ent_ptr->bd.BDStat=0xff;
-				fda_ent_ptr->fd.FDCtl=FDCTL_COWNSFD_MSK;
-
-				/* Allocate a new skb and point the bd entry to it */
-				blist_ent_ptr->fd.FDSystem=0;
-				skb=dev_alloc_skb(PKT_BUF_SZ);
-				//printk("allocskb=%#x\n",skb);
-				if(skb){
-					setup_blist_entry(skb,blist_ent_ptr);
-
-				}
-				else if(!priv->memupdate_scheduled){
-					int tmp;
-					/* There are no buffers at the moment, so schedule */
-					/* the background task to sort this out */
-					schedule_task(&priv->tq_memupdate);
-					priv->memupdate_scheduled=1;
-					printk(KERN_DEBUG "%s:No buffers",dev->name);
-					/* If this interrupt was due to a lack of buffers then
-					 * we'd better stop the receiver too */
-					if(interruptValue&ETHER_INT_SRC_BLEX_MSK){
-						priv->rx_disabled=1;
-						tmp=readl(ETHER_INT_SRC(dev->base_addr));
-						writel(tmp&~ETHER_RX_CTL_RXEN_MSK,ETHER_RX_CTL(dev->base_addr));
-						printk(KERN_DEBUG "%s:Halting rx",dev->name);
-					}
-
-				}
-
-			}
-			fda_ent_ptr++;
-		}
-		spin_unlock(&priv->rx_lock);
-
-		/* Clear the  interrupts */
-		writel(ETHER_INT_SRC_INTMACRX_MSK | ETHER_INT_SRC_FDAEX_MSK
-		       | ETHER_INT_SRC_BLEX_MSK,ETHER_INT_SRC(dev->base_addr));
-
-	}
-
-	if(readl(ETHER_INT_SRC(dev->base_addr))&ETHER_INT_SRC_INTMACTX_MSK){
-
-		if(!priv->memupdate_scheduled){
-			schedule_task(&priv->tq_memupdate);
-			priv->memupdate_scheduled=1;
-		}
-		/* Clear the interrupt */
-		writel(ETHER_INT_SRC_INTMACTX_MSK,ETHER_INT_SRC(dev->base_addr));
-	}
-
-	if (readl(ETHER_INT_SRC(dev->base_addr)) & (ETHER_INT_SRC_SWINT_MSK|
-						    ETHER_INT_SRC_INTEARNOT_MSK|
-						    ETHER_INT_SRC_INTLINK_MSK|
-						    ETHER_INT_SRC_INTEXBD_MSK|
-						    ETHER_INT_SRC_INTTXCTLCMP_MSK))
-	{
-		/*
-		 *	Not using any of these so they shouldn't happen
-		 *
-		 *	In the cased of INTEXBD - if you allocate more
-		 *      than 28 decsriptors you may need to think about this
-		 */
-		printk("Not using this interrupt\n");
-	}
-
-	if (readl(ETHER_INT_SRC(dev->base_addr)) &
-	    (ETHER_INT_SRC_INTSBUS_MSK |
-	     ETHER_INT_SRC_INTNRABT_MSK
-	     |ETHER_INT_SRC_DMPARERR_MSK))
-	{
-		/*
-		 * Hardware errors, we can either ignore them and hope they go away
-		 *or reset the device, I'll try the first for now to see if they happen
-		 */
-		printk("Hardware error\n");
-	}
-}
-
-static void ether00_setup_ethernet_address(struct net_device* dev)
-{
-	int tmp;
-
-	dev->addr_len=6;
-	writew(0,ETHER_ARC_ADR(dev->base_addr));
-	writel((dev->dev_addr[0]<<24) |
-		(dev->dev_addr[1]<<16) |
-		(dev->dev_addr[2]<<8) |
-		dev->dev_addr[3],
-		ETHER_ARC_DATA(dev->base_addr));
-
-	writew(4,ETHER_ARC_ADR(dev->base_addr));
-	tmp=readl(ETHER_ARC_DATA(dev->base_addr));
-	tmp&=0xffff;
-	tmp|=(dev->dev_addr[4]<<24) | (dev->dev_addr[5]<<16);
-	writel(tmp, ETHER_ARC_DATA(dev->base_addr));
-	/* Enable this entry in the ARC */
-
-	writel(1,ETHER_ARC_ENA(dev->base_addr));
-
-	return;
-}
-
-
-static void ether00_reset(struct net_device *dev)
-{
-	/* reset the controller */
-	writew(ETHER_MAC_CTL_RESET_MSK,ETHER_MAC_CTL(dev->base_addr));
-
-	/*
-	 * Make sure we're not going to send anything
-	 */
-
-	writew(ETHER_TX_CTL_TXHALT_MSK,ETHER_TX_CTL(dev->base_addr));
-
-	/*
-	 * Make sure we're not going to receive anything
-	 */
-	writew(ETHER_RX_CTL_RXHALT_MSK,ETHER_RX_CTL(dev->base_addr));
-
-	/*
-	 * Disable Interrupts for now, and set the burst size to 8 bytes
-	 */
-
-	writel(ETHER_DMA_CTL_INTMASK_MSK |
-	       ((8 << ETHER_DMA_CTL_DMBURST_OFST) & ETHER_DMA_CTL_DMBURST_MSK)
-	       |(2<<ETHER_DMA_CTL_RXALIGN_OFST),
-	       ETHER_DMA_CTL(dev->base_addr));
-
-
-	/*
-	 * Set TxThrsh - start transmitting a packet after 1514
-	 * bytes or when a packet is complete, whichever comes first
-	 */
-	 writew(1514,ETHER_TXTHRSH(dev->base_addr));
-
-	/*
-	 * Set TxPollCtr.  Each cycle is
-	 * 61.44 microseconds with a 33 MHz bus
-	 */
-	 writew(1,ETHER_TXPOLLCTR(dev->base_addr));
-
-	/*
-	 * Set Rx_Ctl - Turn off reception and let RxData turn it
-	 * on later
-	 */
-	 writew(ETHER_RX_CTL_RXHALT_MSK,ETHER_RX_CTL(dev->base_addr));
-
-}
-
-
-static void ether00_set_multicast(struct net_device* dev)
-{
-	int count=dev->mc_count;
-
-	/* Set promiscuous mode if it's asked for. */
-
-	if (dev->flags&IFF_PROMISC){
-
-		writew( ETHER_ARC_CTL_COMPEN_MSK |
-			ETHER_ARC_CTL_BROADACC_MSK |
-			ETHER_ARC_CTL_GROUPACC_MSK |
-			ETHER_ARC_CTL_STATIONACC_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-		return;
-	}
-
-	/*
-	 * Get all multicast packets if required, or if there are too
-	 * many addresses to fit in hardware
-	 */
-	if (dev->flags & IFF_ALLMULTI){
-		writew( ETHER_ARC_CTL_COMPEN_MSK |
-			ETHER_ARC_CTL_GROUPACC_MSK |
-			ETHER_ARC_CTL_BROADACC_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-		return;
-	}
-	if (dev->mc_count > (ETHER_ARC_SIZE - 1)){
-
-		printk(KERN_WARNING "Too many multicast addresses for hardware to filter - receiving all multicast packets\n");
-		writew( ETHER_ARC_CTL_COMPEN_MSK |
-			ETHER_ARC_CTL_GROUPACC_MSK |
-			ETHER_ARC_CTL_BROADACC_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-		return;
-	}
-
-	if(dev->mc_count){
-		struct dev_mc_list *mc_list_ent=dev->mc_list;
-		unsigned int temp,i;
-		DEBUG(printk("mc_count=%d mc_list=%#x\n",dev-> mc_count, dev->mc_list));
-		DEBUG(printk("mc addr=%02#x%02x%02x%02x%02x%02x\n",
-			     mc_list_ent->dmi_addr[5],
-			     mc_list_ent->dmi_addr[4],
-			     mc_list_ent->dmi_addr[3],
-			     mc_list_ent->dmi_addr[2],
-			     mc_list_ent->dmi_addr[1],
-			     mc_list_ent->dmi_addr[0]);)
-
-		/*
-		 * The first 6 bytes are the MAC address, so
-		 * don't change them!
-		 */
-		writew(4,ETHER_ARC_ADR(dev->base_addr));
-		temp=readl(ETHER_ARC_DATA(dev->base_addr));
-		temp&=0xffff0000;
-
-		/* Disable the current multicast stuff */
-		writel(1,ETHER_ARC_ENA(dev->base_addr));
-
-		for(;;){
-			temp|=mc_list_ent->dmi_addr[1] |
-				mc_list_ent->dmi_addr[0]<<8;
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			i=readl(ETHER_ARC_ADR(dev->base_addr));
-			writew(i+4,ETHER_ARC_ADR(dev->base_addr));
-
-			temp=mc_list_ent->dmi_addr[5]|
-				mc_list_ent->dmi_addr[4]<<8 |
-				mc_list_ent->dmi_addr[3]<<16 |
-				mc_list_ent->dmi_addr[2]<<24;
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			count--;
-			if(!mc_list_ent->next || !count){
-				break;
-			}
-			DEBUG(printk("mc_list_next=%#x\n",mc_list_ent->next);)
-			mc_list_ent=mc_list_ent->next;
-
-
-			i=readl(ETHER_ARC_ADR(dev->base_addr));
-			writel(i+4,ETHER_ARC_ADR(dev->base_addr));
-
-			temp=mc_list_ent->dmi_addr[3]|
-				mc_list_ent->dmi_addr[2]<<8 |
-				mc_list_ent->dmi_addr[1]<<16 |
-				mc_list_ent->dmi_addr[0]<<24;
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			i=readl(ETHER_ARC_ADR(dev->base_addr));
-			writel(i+4,ETHER_ARC_ADR(dev->base_addr));
-
-			temp=mc_list_ent->dmi_addr[4]<<16 |
-				mc_list_ent->dmi_addr[5]<<24;
-
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			count--;
-			if(!mc_list_ent->next || !count){
-				break;
-			}
-			mc_list_ent=mc_list_ent->next;
-		}
-
-
-		if(count)
-			printk(KERN_WARNING "Multicast list size error\n");
-
-
-		writew( ETHER_ARC_CTL_BROADACC_MSK|
-			ETHER_ARC_CTL_COMPEN_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-
-	}
-
-	/* enable the active ARC enties */
-	writew((1<<(count+2))-1,ETHER_ARC_ENA(dev->base_addr));
-}
-
-
-static int ether00_open(struct net_device* dev)
-{
-	int result,tmp;
-	struct net_priv* priv;
-
-	if (!is_valid_ether_addr(dev->dev_addr))
-		return -EINVAL;
-
-	/* Install interrupt handlers */
-	result=request_irq(dev->irq,ether00_int,0,"ether00",dev);
-	if(result)
-		goto open_err1;
-
-	result=request_irq(2,ether00_phy_int,0,"ether00_phy",dev);
-	if(result)
-		goto open_err2;
-
-	ether00_reset(dev);
-	result=ether00_mem_init(dev);
-	if(result)
-		goto open_err3;
-
-
-	ether00_setup_ethernet_address(dev);
-
-	ether00_set_multicast(dev);
-
-	result=ether00_write_phy(dev,PHY_CONTROL, PHY_CONTROL_ANEGEN_MSK | PHY_CONTROL_RANEG_MSK);
-	if(result)
-		goto open_err4;
-	result=ether00_write_phy(dev,PHY_IRQ_CONTROL, PHY_IRQ_CONTROL_LS_CHG_IE_MSK |
-				 PHY_IRQ_CONTROL_ANEG_COMP_IE_MSK);
-	if(result)
-		goto open_err4;
-
-	/* Start the device enable interrupts */
-	writew(ETHER_RX_CTL_RXEN_MSK
-//	       | ETHER_RX_CTL_STRIPCRC_MSK
-	       | ETHER_RX_CTL_ENGOOD_MSK
-	       | ETHER_RX_CTL_ENRXPAR_MSK| ETHER_RX_CTL_ENLONGERR_MSK
-	       | ETHER_RX_CTL_ENOVER_MSK| ETHER_RX_CTL_ENCRCERR_MSK,
-	       ETHER_RX_CTL(dev->base_addr));
-
-	writew(ETHER_TX_CTL_TXEN_MSK|
-	       ETHER_TX_CTL_ENEXDEFER_MSK|
-	       ETHER_TX_CTL_ENLCARR_MSK|
-	       ETHER_TX_CTL_ENEXCOLL_MSK|
-	       ETHER_TX_CTL_ENLATECOLL_MSK|
-	       ETHER_TX_CTL_ENTXPAR_MSK|
-	       ETHER_TX_CTL_ENCOMP_MSK,
-	       ETHER_TX_CTL(dev->base_addr));
-
-	tmp=readl(ETHER_DMA_CTL(dev->base_addr));
-	writel(tmp&~ETHER_DMA_CTL_INTMASK_MSK,ETHER_DMA_CTL(dev->base_addr));
-
-	return 0;
-
- open_err4:
-	ether00_reset(dev);
- open_err3:
-	free_irq(2,dev);
- open_err2:
-	free_irq(dev->irq,dev);
- open_err1:
-	return result;
-
-}
-
-
-static int ether00_tx(struct sk_buff* skb, struct net_device* dev)
-{
-	struct net_priv *priv=dev->priv;
-	struct tx_fda_ent *fda_ptr;
-	int i;
-
-
-	/*
-	 *	Find an empty slot in which to stick the frame
-	 */
-	fda_ptr=(struct tx_fda_ent*)__dma_va(readl(ETHER_TXFRMPTR(dev->base_addr)));
-	i=0;
-	while(i<TX_NUM_FDESC){
-		if (fda_ptr->fd.FDStat||(fda_ptr->fd.FDCtl & FDCTL_COWNSFD_MSK)){
-			fda_ptr =(struct tx_fda_ent*) __dma_va((struct tx_fda_ent*)fda_ptr->fd.FDNext);
-		}
-		else {
-			break;
-		}
-		i++;
-	}
-
-	/* Write the skb data from the cache*/
-	consistent_sync(skb->data,skb->len,PCI_DMA_TODEVICE);
-	fda_ptr->bd.BuffData=(char*)__pa(skb->data);
-	fda_ptr->bd.BuffLength=(unsigned short)skb->len;
-	/* Save the pointer to the skb for freeing later */
-	fda_ptr->fd.FDSystem=(unsigned int)skb;
-	fda_ptr->fd.FDStat=0;
-	/* Pass ownership of the buffers to the controller */
-	fda_ptr->fd.FDCtl=1;
-	fda_ptr->fd.FDCtl|=FDCTL_COWNSFD_MSK;
-
-	/* If the next buffer in the list is full, stop the queue */
-	fda_ptr=(struct tx_fda_ent*)__dma_va(fda_ptr->fd.FDNext);
-	if ((fda_ptr->fd.FDStat)||(fda_ptr->fd.FDCtl & FDCTL_COWNSFD_MSK)){
-		netif_stop_queue(dev);
-		priv->queue_stopped=1;
-	}
-
-	return 0;
-}
-
-static struct net_device_stats *ether00_stats(struct net_device* dev)
-{
-	struct net_priv *priv=dev->priv;
-	return &priv->stats;
-}
-
-
-static int ether00_stop(struct net_device* dev)
-{
-	struct net_priv *priv=dev->priv;
-	int tmp;
-
-	/* Stop/disable the device. */
-	tmp=readw(ETHER_RX_CTL(dev->base_addr));
-	tmp&=~(ETHER_RX_CTL_RXEN_MSK | ETHER_RX_CTL_ENGOOD_MSK);
-	tmp|=ETHER_RX_CTL_RXHALT_MSK;
-	writew(tmp,ETHER_RX_CTL(dev->base_addr));
-
-	tmp=readl(ETHER_TX_CTL(dev->base_addr));
-	tmp&=~ETHER_TX_CTL_TXEN_MSK;
-	tmp|=ETHER_TX_CTL_TXHALT_MSK;
-	writel(tmp,ETHER_TX_CTL(dev->base_addr));
-
-	/* Free up system resources */
-	free_irq(dev->irq,dev);
-	free_irq(2,dev);
-	iounmap(priv->dma_data);
-
-	return 0;
-}
-
-
-static void ether00_get_ethernet_address(struct net_device* dev)
-{
-	struct mtd_info *mymtd=NULL;
-	int i;
-	size_t retlen;
-
-	/*
-	 * For the Epxa10 dev board (camelot), the ethernet MAC
-	 * address is of the form  00:aa:aa:00:xx:xx where
-	 * 00:aa:aa is the Altera vendor ID and xx:xx is the
-	 * last 2 bytes of the board serial number, as programmed
-	 * into the OTP area of the flash device on EBI1. If this
-	 * isn't an expa10 dev board, or there's no mtd support to
-	 * read the serial number from flash then we'll force the
-	 * use to set their own mac address using ifconfig.
-	 */
-
-#ifdef CONFIG_ARCH_CAMELOT
-#ifdef CONFIG_MTD
-	/* get the mtd_info structure for the first mtd device*/
-	for(i=0;i<MAX_MTD_DEVICES;i++){
-		mymtd=get_mtd_device(NULL,i);
-		if(!mymtd||!strcmp(mymtd->name,"EPXA10DB flash"))
-			break;
-	}
-
-	if(!mymtd || !mymtd->read_user_prot_reg){
-		printk(KERN_WARNING "%s: Failed to read MAC address from flash\n",dev->name);
-	}else{
-		mymtd->read_user_prot_reg(mymtd,2,1,&retlen,&dev->dev_addr[5]);
-		mymtd->read_user_prot_reg(mymtd,3,1,&retlen,&dev->dev_addr[4]);
-		dev->dev_addr[3]=0;
-		dev->dev_addr[2]=vendor_id[1];
-		dev->dev_addr[1]=vendor_id[0];
-		dev->dev_addr[0]=0;
-	}
-#else
-	printk(KERN_WARNING "%s: MTD support required to read MAC address from EPXA10 dev board\n", dev->name);
-#endif
-#endif
-
-	if (!is_valid_ether_addr(dev->dev_addr))
-		printk("%s: Invalid ethernet MAC address.  Please set using "
-			"ifconfig\n", dev->name);
-
-}
-
-/*
- * Keep a mapping of dev_info addresses -> port lines to use when
- * removing ports dev==NULL indicates unused entry
- */
-
-
-static struct net_device* dev_list[ETH_NR];
-
-static int ether00_add_device(struct pldhs_dev_info* dev_info,void* dev_ps_data)
-{
-	struct net_device *dev;
-	struct net_priv *priv;
-	void *map_addr;
-	int result;
-	int i;
-
-	i=0;
-	while(dev_list[i] && i < ETH_NR)
-		i++;
-
-	if(i==ETH_NR){
-		printk(KERN_WARNING "ether00: Maximum number of ports reached\n");
-		return 0;
-	}
-
-
-	if (!request_mem_region(dev_info->base_addr, MAC_REG_SIZE, "ether00"))
-		return -EBUSY;
-
-	dev = alloc_etherdev(sizeof(struct net_priv));
-	if(!dev) {
-		result = -ENOMEM;
-		goto out_release;
-	}
-	priv = dev->priv;
-
-	priv->tq_memupdate.routine=ether00_mem_update;
-	priv->tq_memupdate.data=(void*) dev;
-
-	spin_lock_init(&priv->rx_lock);
-
-	map_addr=ioremap_nocache(dev_info->base_addr,SZ_4K);
-	if(!map_addr){
-		result = -ENOMEM;
-		out_kfree;
-	}
-
-	dev->open=ether00_open;
-	dev->stop=ether00_stop;
-	dev->set_multicast_list=ether00_set_multicast;
-	dev->hard_start_xmit=ether00_tx;
-	dev->get_stats=ether00_stats;
-
-	ether00_get_ethernet_address(dev);
-
-	SET_MODULE_OWNER(dev);
-
-	dev->base_addr=(unsigned int)map_addr;
-	dev->irq=dev_info->irq;
-	dev->features=NETIF_F_DYNALLOC | NETIF_F_HW_CSUM;
-
-	result=register_netdev(dev);
-	if(result){
-		printk("Ether00: Error %i registering driver\n",result);
-		goto out_unmap;
-	}
-	printk("registered ether00 device at %#x\n",dev_info->base_addr);
-
-	dev_list[i]=dev;
-
-	return result;
-
- out_unmap:
-	iounmap(map_addr);
- out_kfree:
-	free_netdev(dev);
- out_release:
-	release_mem_region(dev_info->base_addr, MAC_REG_SIZE);
-	return result;
-}
-
-
-static int ether00_remove_devices(void)
-{
-	int i;
-
-	for(i=0;i<ETH_NR;i++){
-		if(dev_list[i]){
-			netif_device_detach(dev_list[i]);
-			unregister_netdev(dev_list[i]);
-			iounmap((void*)dev_list[i]->base_addr);
-			release_mem_region(dev_list[i]->base_addr, MAC_REG_SIZE);
-			free_netdev(dev_list[i]);
-			dev_list[i]=0;
-		}
-	}
-	return 0;
-}
-
-static struct pld_hotswap_ops ether00_pldhs_ops={
-	.name = ETHER00_NAME,
-	.add_device = ether00_add_device,
-	.remove_devices = ether00_remove_devices,
-};
-
-
-static void __exit ether00_cleanup_module(void)
-{
-	int result;
-	result=ether00_remove_devices();
-	if(result)
-		printk(KERN_WARNING "ether00: failed to remove all devices\n");
-
-	pldhs_unregister_driver(ETHER00_NAME);
-}
-module_exit(ether00_cleanup_module);
-
-
-static int __init ether00_mod_init(void)
-{
-	printk("mod init\n");
-	return pldhs_register_driver(&ether00_pldhs_ops);
-
-}
-
-module_init(ether00_mod_init);
-
diff --git a/drivers/net/arm/ether3.c b/drivers/net/arm/ether3.c
index 1cc53ab..f1d5b10 100644
--- a/drivers/net/arm/ether3.c
+++ b/drivers/net/arm/ether3.c
@@ -69,7 +69,6 @@
 #include <asm/system.h>
 #include <asm/ecard.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 
 static char version[] __initdata = "ether3 ethernet driver (c) 1995-2000 R.M.King v1.17\n";
 
diff --git a/drivers/net/arm/etherh.c b/drivers/net/arm/etherh.c
index 942a281..6a93b66 100644
--- a/drivers/net/arm/etherh.c
+++ b/drivers/net/arm/etherh.c
@@ -50,7 +50,6 @@
 #include <asm/system.h>
 #include <asm/ecard.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 
 #include "../8390.h"
 
diff --git a/drivers/scsi/arm/acornscsi.c b/drivers/scsi/arm/acornscsi.c
index 09ed057..dda5a5f 100644
--- a/drivers/scsi/arm/acornscsi.c
+++ b/drivers/scsi/arm/acornscsi.c
@@ -146,7 +146,6 @@
 
 #include <asm/system.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/ecard.h>
 
 #include "../scsi.h"
diff --git a/drivers/scsi/arm/arxescsi.c b/drivers/scsi/arm/arxescsi.c
index 804125e..a289401 100644
--- a/drivers/scsi/arm/arxescsi.c
+++ b/drivers/scsi/arm/arxescsi.c
@@ -33,7 +33,6 @@
 
 #include <asm/dma.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/ecard.h>
 
 #include "../scsi.h"
diff --git a/drivers/scsi/arm/cumana_1.c b/drivers/scsi/arm/cumana_1.c
index 81e266b..e6c9491 100644
--- a/drivers/scsi/arm/cumana_1.c
+++ b/drivers/scsi/arm/cumana_1.c
@@ -13,7 +13,6 @@
 
 #include <asm/ecard.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/system.h>
 
 #include "../scsi.h"
diff --git a/drivers/scsi/arm/cumana_2.c b/drivers/scsi/arm/cumana_2.c
index 3a7a46b..583d2d8 100644
--- a/drivers/scsi/arm/cumana_2.c
+++ b/drivers/scsi/arm/cumana_2.c
@@ -31,7 +31,6 @@
 #include <asm/dma.h>
 #include <asm/ecard.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/pgtable.h>
 
 #include "../scsi.h"
diff --git a/drivers/scsi/arm/eesox.c b/drivers/scsi/arm/eesox.c
index 4d1e8f5..3ffec7e 100644
--- a/drivers/scsi/arm/eesox.c
+++ b/drivers/scsi/arm/eesox.c
@@ -35,7 +35,6 @@
 #include <linux/dma-mapping.h>
 
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/dma.h>
 #include <asm/ecard.h>
 #include <asm/pgtable.h>
diff --git a/drivers/scsi/arm/powertec.c b/drivers/scsi/arm/powertec.c
index 3333d7b..3113bdc 100644
--- a/drivers/scsi/arm/powertec.c
+++ b/drivers/scsi/arm/powertec.c
@@ -22,7 +22,6 @@
 #include <asm/dma.h>
 #include <asm/ecard.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/pgtable.h>
 
 #include "../scsi.h"
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 3fd5b99..1bae26a 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -369,29 +369,6 @@ config SERIAL_21285_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
-config SERIAL_UART00
-	bool "Excalibur serial port (uart00) support"
-	depends on ARM && ARCH_CAMELOT
-	select SERIAL_CORE
-	help
-	  Say Y here if you want to use the hard logic uart on Excalibur. This
-	  driver also supports soft logic implementations of this uart core.
-
-config SERIAL_UART00_CONSOLE
-	bool "Support for console on Excalibur serial port"
-	depends on SERIAL_UART00
-	select SERIAL_CORE_CONSOLE
-	help
-	  Say Y here if you want to support a serial console on an Excalibur
-	  hard logic uart or uart00 IP core.
-
-	  Even if you say Y here, the currently visible virtual console
-	  (/dev/tty0) will still be used as the system console by default, but
-	  you can alter that using a kernel command line option such as
-	  "console=ttyS1". (Try "man bootparam" or see the documentation of
-	  your boot loader (lilo or loadlin) about how to pass options to the
-	  kernel at boot time.)
-
 config SERIAL_MPSC
 	bool "Marvell MPSC serial port support"
 	depends on PPC32 && MV64X60
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index d7c7c71..137148b 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -29,7 +29,6 @@ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
 obj-$(CONFIG_SERIAL_PXA) += pxa.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
 obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
-obj-$(CONFIG_SERIAL_UART00) += uart00.o
 obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
 obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o
 obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o
diff --git a/drivers/serial/uart00.c b/drivers/serial/uart00.c
deleted file mode 100644
index 47b504f..0000000
--- a/drivers/serial/uart00.c
+++ /dev/null
@@ -1,782 +0,0 @@
-/*
- *  linux/drivers/serial/uart00.c
- *
- *  Driver for UART00 serial ports
- *
- *  Based on drivers/char/serial_amba.c, by ARM Limited & 
- *                                          Deep Blue Solutions Ltd.
- *  Copyright 2001 Altera Corporation
- *
- *  Update for 2.6.4 by Dirk Behme <dirk.behme@de.bosch.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- *  $Id: uart00.c,v 1.35 2002/07/28 10:03:28 rmk Exp $
- *
- */
-#include <linux/config.h>
-
-#if defined(CONFIG_SERIAL_UART00_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/sysrq.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/sizes.h>
-
-#include <asm/arch/excalibur.h>
-#define UART00_TYPE (volatile unsigned int*)
-#include <asm/arch/uart00.h>
-#include <asm/arch/int_ctrl00.h>
-
-#define UART_NR		2
-
-#define SERIAL_UART00_NAME	"ttyUA"
-#define SERIAL_UART00_MAJOR	204
-#define SERIAL_UART00_MINOR	16      /* Temporary - will change in future */
-#define SERIAL_UART00_NR	UART_NR
-#define UART_PORT_SIZE 0x50
-
-#define UART00_ISR_PASS_LIMIT	256
-
-/*
- * Access macros for the UART00 UARTs
- */
-#define UART_GET_INT_STATUS(p)	inl(UART_ISR((p)->membase))
-#define UART_PUT_IES(p, c)      outl(c,UART_IES((p)->membase))
-#define UART_GET_IES(p)         inl(UART_IES((p)->membase))
-#define UART_PUT_IEC(p, c)      outl(c,UART_IEC((p)->membase))
-#define UART_GET_IEC(p)         inl(UART_IEC((p)->membase))
-#define UART_PUT_CHAR(p, c)     outl(c,UART_TD((p)->membase))
-#define UART_GET_CHAR(p)        inl(UART_RD((p)->membase))
-#define UART_GET_RSR(p)         inl(UART_RSR((p)->membase))
-#define UART_GET_RDS(p)         inl(UART_RDS((p)->membase))
-#define UART_GET_MSR(p)         inl(UART_MSR((p)->membase))
-#define UART_GET_MCR(p)         inl(UART_MCR((p)->membase))
-#define UART_PUT_MCR(p, c)      outl(c,UART_MCR((p)->membase))
-#define UART_GET_MC(p)          inl(UART_MC((p)->membase))
-#define UART_PUT_MC(p, c)       outl(c,UART_MC((p)->membase))
-#define UART_GET_TSR(p)         inl(UART_TSR((p)->membase))
-#define UART_GET_DIV_HI(p)	inl(UART_DIV_HI((p)->membase))
-#define UART_PUT_DIV_HI(p,c)	outl(c,UART_DIV_HI((p)->membase))
-#define UART_GET_DIV_LO(p)	inl(UART_DIV_LO((p)->membase))
-#define UART_PUT_DIV_LO(p,c)	outl(c,UART_DIV_LO((p)->membase))
-#define UART_RX_DATA(s)		((s) & UART_RSR_RX_LEVEL_MSK)
-#define UART_TX_READY(s)	(((s) & UART_TSR_TX_LEVEL_MSK) < 15)
-//#define UART_TX_EMPTY(p)	((UART_GET_FR(p) & UART00_UARTFR_TMSK) == 0)
-
-static void uart00_stop_tx(struct uart_port *port)
-{
-	UART_PUT_IEC(port, UART_IEC_TIE_MSK);
-}
-
-static void uart00_stop_rx(struct uart_port *port)
-{
-	UART_PUT_IEC(port, UART_IEC_RE_MSK);
-}
-
-static void uart00_enable_ms(struct uart_port *port)
-{
-	UART_PUT_IES(port, UART_IES_ME_MSK);
-}
-
-static void
-uart00_rx_chars(struct uart_port *port, struct pt_regs *regs)
-{
-	struct tty_struct *tty = port->info->tty;
-	unsigned int status, ch, rds, flg, ignored = 0;
-
-	status = UART_GET_RSR(port);
-	while (UART_RX_DATA(status)) {
-		/* 
-		 * We need to read rds before reading the 
-		 * character from the fifo
-		 */
-		rds = UART_GET_RDS(port);
-		ch = UART_GET_CHAR(port);
-		port->icount.rx++;
-
-		if (tty->flip.count >= TTY_FLIPBUF_SIZE)
-			goto ignore_char;
-
-		flg = TTY_NORMAL;
-
-		/*
-		 * Note that the error handling code is
-		 * out of the main execution path
-		 */
-		if (rds & (UART_RDS_BI_MSK |UART_RDS_FE_MSK|
-			   UART_RDS_PE_MSK |UART_RDS_PE_MSK))
-			goto handle_error;
-		if (uart_handle_sysrq_char(port, ch, regs))
-			goto ignore_char;
-
-	error_return:
-		tty_insert_flip_char(tty, ch, flg);
-
-	ignore_char:
-		status = UART_GET_RSR(port);
-	}
- out:
-	tty_flip_buffer_push(tty);
-	return;
-
- handle_error:
-	if (rds & UART_RDS_BI_MSK) {
-		status &= ~(UART_RDS_FE_MSK | UART_RDS_PE_MSK);
-		port->icount.brk++;
-		if (uart_handle_break(port))
-			goto ignore_char;
-	} else if (rds & UART_RDS_PE_MSK)
-		port->icount.parity++;
-	else if (rds & UART_RDS_FE_MSK)
-		port->icount.frame++;
-	if (rds & UART_RDS_OE_MSK)
-		port->icount.overrun++;
-
-	if (rds & port->ignore_status_mask) {
-		if (++ignored > 100)
-			goto out;
-		goto ignore_char;
-	}
-	rds &= port->read_status_mask;
-
-	if (rds & UART_RDS_BI_MSK)
-		flg = TTY_BREAK;
-	else if (rds & UART_RDS_PE_MSK)
-		flg = TTY_PARITY;
-	else if (rds & UART_RDS_FE_MSK)
-		flg = TTY_FRAME;
-
-	if (rds & UART_RDS_OE_MSK) {
-		/*
-		 * CHECK: does overrun affect the current character?
-		 * ASSUMPTION: it does not.
-		 */
-		tty_insert_flip_char(tty, ch, flg);
-		ch = 0;
-		flg = TTY_OVERRUN;
-	}
-#ifdef SUPPORT_SYSRQ
-	port->sysrq = 0;
-#endif
-	goto error_return;
-}
-
-static void uart00_tx_chars(struct uart_port *port)
-{
-	struct circ_buf *xmit = &port->info->xmit;
-	int count;
-
-	if (port->x_char) {
-		while ((UART_GET_TSR(port) & UART_TSR_TX_LEVEL_MSK) == 15)
-			barrier();
-		UART_PUT_CHAR(port, port->x_char);
-		port->icount.tx++;
-		port->x_char = 0;
-		return;
-	}
-	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
-		uart00_stop_tx(port);
-		return;
-	}
-
-	count = port->fifosize >> 1;
-	do {
-		while ((UART_GET_TSR(port) & UART_TSR_TX_LEVEL_MSK) == 15)
-			barrier();
-		UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		port->icount.tx++;
-		if (uart_circ_empty(xmit))
-			break;
-	} while (--count > 0);
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(port);
-
-	if (uart_circ_empty(xmit))
-		uart00_stop_tx(port);
-}
-
-static void uart00_start_tx(struct uart_port *port)
-{
-	UART_PUT_IES(port, UART_IES_TIE_MSK);
-	uart00_tx_chars(port);
-}
-
-static void uart00_modem_status(struct uart_port *port)
-{
-	unsigned int status;
-
-	status = UART_GET_MSR(port);
-
-	if (!(status & (UART_MSR_DCTS_MSK | UART_MSR_DDSR_MSK | 
-			UART_MSR_TERI_MSK | UART_MSR_DDCD_MSK)))
-		return;
-
-	if (status & UART_MSR_DDCD_MSK)
-		uart_handle_dcd_change(port, status & UART_MSR_DCD_MSK);
-
-	if (status & UART_MSR_DDSR_MSK)
-		port->icount.dsr++;
-
-	if (status & UART_MSR_DCTS_MSK)
-		uart_handle_cts_change(port, status & UART_MSR_CTS_MSK);
-
-	wake_up_interruptible(&port->info->delta_msr_wait);
-}
-
-static irqreturn_t uart00_int(int irq, void *dev_id, struct pt_regs *regs)
-{
-	struct uart_port *port = dev_id;
-	unsigned int status, pass_counter = 0;
-
-	status = UART_GET_INT_STATUS(port);
-	do {
-		if (status & UART_ISR_RI_MSK)
-			uart00_rx_chars(port, regs);
-		if (status & UART_ISR_MI_MSK)
-			uart00_modem_status(port);
-		if (status & (UART_ISR_TI_MSK | UART_ISR_TII_MSK))
-			uart00_tx_chars(port);
-		if (pass_counter++ > UART00_ISR_PASS_LIMIT)
-			break;
-
-		status = UART_GET_INT_STATUS(port);
-	} while (status);
-
-	return IRQ_HANDLED;
-}
-
-static unsigned int uart00_tx_empty(struct uart_port *port)
-{
-	return UART_GET_TSR(port) & UART_TSR_TX_LEVEL_MSK? 0 : TIOCSER_TEMT;
-}
-
-static unsigned int uart00_get_mctrl(struct uart_port *port)
-{
-	unsigned int result = 0;
-	unsigned int status;
-
-	status = UART_GET_MSR(port);
-	if (status & UART_MSR_DCD_MSK)
-		result |= TIOCM_CAR;
-	if (status & UART_MSR_DSR_MSK)
-		result |= TIOCM_DSR;
-	if (status & UART_MSR_CTS_MSK)
-		result |= TIOCM_CTS;
-	if (status & UART_MSR_RI_MSK)
-		result |= TIOCM_RI;
-
-	return result;
-}
-
-static void uart00_set_mctrl_null(struct uart_port *port, unsigned int mctrl)
-{
-}
-
-static void uart00_break_ctl(struct uart_port *port, int break_state)
-{
-	unsigned long flags;
-	unsigned int mcr;
-
-	spin_lock_irqsave(&port->lock, flags);
-	mcr = UART_GET_MCR(port);
-	if (break_state == -1)
-		mcr |= UART_MCR_BR_MSK;
-	else
-		mcr &= ~UART_MCR_BR_MSK;
-	UART_PUT_MCR(port, mcr);
-	spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static void
-uart00_set_termios(struct uart_port *port, struct termios *termios,
-		   struct termios *old)
-{
-	unsigned int uart_mc, old_ies, baud, quot;
-	unsigned long flags;
-
-	/*
-	 * We don't support CREAD (yet)
-	 */
-	termios->c_cflag |= CREAD;
-
-	/*
-	 * Ask the core to calculate the divisor for us.
-	 */
-	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
-	quot = uart_get_divisor(port, baud);
-
-	/* byte size and parity */
-	switch (termios->c_cflag & CSIZE) {
-	case CS5:
-		uart_mc = UART_MC_CLS_CHARLEN_5;
-		break;
-	case CS6:
-		uart_mc = UART_MC_CLS_CHARLEN_6;
-		break;
-	case CS7:
-		uart_mc = UART_MC_CLS_CHARLEN_7;
-		break;
-	default: // CS8
-		uart_mc = UART_MC_CLS_CHARLEN_8;
-		break;
-	}
-	if (termios->c_cflag & CSTOPB)
-		uart_mc|= UART_MC_ST_TWO;
-	if (termios->c_cflag & PARENB) {
-		uart_mc |= UART_MC_PE_MSK;
-		if (!(termios->c_cflag & PARODD))
-			uart_mc |= UART_MC_EP_MSK;
-	}
-
-	spin_lock_irqsave(&port->lock, flags);
-
-	/*
-	 * Update the per-port timeout.
-	 */
-	uart_update_timeout(port, termios->c_cflag, baud);
-
-	port->read_status_mask = UART_RDS_OE_MSK;
-	if (termios->c_iflag & INPCK)
-		port->read_status_mask |= UART_RDS_FE_MSK | UART_RDS_PE_MSK;
-	if (termios->c_iflag & (BRKINT | PARMRK))
-		port->read_status_mask |= UART_RDS_BI_MSK;
-
-	/*
-	 * Characters to ignore
-	 */
-	port->ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		port->ignore_status_mask |= UART_RDS_FE_MSK | UART_RDS_PE_MSK;
-	if (termios->c_iflag & IGNBRK) {
-		port->ignore_status_mask |= UART_RDS_BI_MSK;
-		/*
-		 * If we're ignoring parity and break indicators,
-		 * ignore overruns to (for real raw support).
-		 */
-		if (termios->c_iflag & IGNPAR)
-			port->ignore_status_mask |= UART_RDS_OE_MSK;
-	}
-
-	/* first, disable everything */
-	old_ies = UART_GET_IES(port); 
-
-	if (UART_ENABLE_MS(port, termios->c_cflag))
-		old_ies |= UART_IES_ME_MSK;
-
-	/* Set baud rate */
-	UART_PUT_DIV_LO(port, (quot & 0xff));
-	UART_PUT_DIV_HI(port, ((quot & 0xf00) >> 8));
-
-	UART_PUT_MC(port, uart_mc);
-	UART_PUT_IES(port, old_ies);
-
-	spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static int uart00_startup(struct uart_port *port)
-{
-	int result;
-
-	/*
-	 * Allocate the IRQ
-	 */
-	result = request_irq(port->irq, uart00_int, 0, "uart00", port);
-	if (result) {
-		printk(KERN_ERR "Request of irq %d failed\n", port->irq);
-		return result;
-	}
-
-	/*
-	 * Finally, enable interrupts. Use the TII interrupt to minimise 
-	 * the number of interrupts generated. If higher performance is 
-	 * needed, consider using the TI interrupt with a suitable FIFO
-	 * threshold
-	 */
-	UART_PUT_IES(port, UART_IES_RE_MSK | UART_IES_TIE_MSK);
-
-	return 0;
-}
-
-static void uart00_shutdown(struct uart_port *port)
-{
-	/*
-	 * disable all interrupts, disable the port
-	 */
-	UART_PUT_IEC(port, 0xff);
-
-	/* disable break condition and fifos */
-	UART_PUT_MCR(port, UART_GET_MCR(port) &~UART_MCR_BR_MSK);
-
-        /*
-	 * Free the interrupt
-	 */
-	free_irq(port->irq, port);
-}
-
-static const char *uart00_type(struct uart_port *port)
-{
-	return port->type == PORT_UART00 ? "Altera UART00" : NULL;
-}
-
-/*
- * Release the memory region(s) being used by 'port'
- */
-static void uart00_release_port(struct uart_port *port)
-{
-	release_mem_region(port->mapbase, UART_PORT_SIZE);
-
-#ifdef CONFIG_ARCH_CAMELOT
-	if (port->membase != (void*)IO_ADDRESS(EXC_UART00_BASE)) {
-		iounmap(port->membase);
-	}
-#endif
-}
-
-/*
- * Request the memory region(s) being used by 'port'
- */
-static int uart00_request_port(struct uart_port *port)
-{
-	return request_mem_region(port->mapbase, UART_PORT_SIZE, "serial_uart00")
-			!= NULL ? 0 : -EBUSY;
-}
-
-/*
- * Configure/autoconfigure the port.
- */
-static void uart00_config_port(struct uart_port *port, int flags)
-{
-
-	/*
-	 * Map the io memory if this is a soft uart
-	 */
-	if (!port->membase)
-		port->membase = ioremap_nocache(port->mapbase,SZ_4K);
-
-	if (!port->membase)
-		printk(KERN_ERR "serial00: cannot map io memory\n");
-	else
-		port->type = PORT_UART00;
-
-}
-
-/*
- * verify the new serial_struct (for TIOCSSERIAL).
- */
-static int uart00_verify_port(struct uart_port *port, struct serial_struct *ser)
-{
-	int ret = 0;
-	if (ser->type != PORT_UNKNOWN && ser->type != PORT_UART00)
-		ret = -EINVAL;
-	if (ser->irq < 0 || ser->irq >= NR_IRQS)
-		ret = -EINVAL;
-	if (ser->baud_base < 9600)
-		ret = -EINVAL;
-	return ret;
-}
-
-static struct uart_ops uart00_pops = {
-	.tx_empty	= uart00_tx_empty,
-	.set_mctrl	= uart00_set_mctrl_null,
-	.get_mctrl	= uart00_get_mctrl,
-	.stop_tx	= uart00_stop_tx,
-	.start_tx	= uart00_start_tx,
-	.stop_rx	= uart00_stop_rx,
-	.enable_ms	= uart00_enable_ms,
-	.break_ctl	= uart00_break_ctl,
-	.startup	= uart00_startup,
-	.shutdown	= uart00_shutdown,
-	.set_termios	= uart00_set_termios,
-	.type		= uart00_type,
-	.release_port	= uart00_release_port,
-	.request_port	= uart00_request_port,
-	.config_port	= uart00_config_port,
-	.verify_port	= uart00_verify_port,
-};
-
-
-#ifdef CONFIG_ARCH_CAMELOT
-static struct uart_port epxa10db_port = {
-	.membase	= (void*)IO_ADDRESS(EXC_UART00_BASE),
-	.mapbase	= EXC_UART00_BASE,
-	.iotype		= SERIAL_IO_MEM,
-	.irq		= IRQ_UART,
-	.uartclk	= EXC_AHB2_CLK_FREQUENCY,
-	.fifosize	= 16,
-	.ops		= &uart00_pops,
-	.flags		= ASYNC_BOOT_AUTOCONF,
-};
-#endif
-
-
-#ifdef CONFIG_SERIAL_UART00_CONSOLE
-static void uart00_console_write(struct console *co, const char *s, unsigned count)
-{
-#ifdef CONFIG_ARCH_CAMELOT
-	struct uart_port *port = &epxa10db_port;
-	unsigned int status, old_ies;
-	int i;
-
-	/*
-	 *	First save the CR then disable the interrupts
-	 */
-	old_ies = UART_GET_IES(port);
-	UART_PUT_IEC(port,0xff);
-
-	/*
-	 *	Now, do each character
-	 */
-	for (i = 0; i < count; i++) {
-		do {
-			status = UART_GET_TSR(port);
-		} while (!UART_TX_READY(status));
-		UART_PUT_CHAR(port, s[i]);
-		if (s[i] == '\n') {
-			do {
-				status = UART_GET_TSR(port);
-			} while (!UART_TX_READY(status));
-			UART_PUT_CHAR(port, '\r');
-		}
-	}
-
-	/*
-	 *	Finally, wait for transmitter to become empty
-	 *	and restore the IES
-	 */
-	do {
-		status = UART_GET_TSR(port);
-	} while (status & UART_TSR_TX_LEVEL_MSK);
-	UART_PUT_IES(port, old_ies);
-#endif
-}
-
-static void __init
-uart00_console_get_options(struct uart_port *port, int *baud,
-			   int *parity, int *bits)
-{
-	unsigned int uart_mc, quot;
-
-	uart_mc = UART_GET_MC(port);
-
-	*parity = 'n';
-	if (uart_mc & UART_MC_PE_MSK) {
-		if (uart_mc & UART_MC_EP_MSK)
-			*parity = 'e';
-		else
-			*parity = 'o';
-	}
-
-	switch (uart_mc & UART_MC_CLS_MSK) {
-	case UART_MC_CLS_CHARLEN_5:
-		*bits = 5;
-		break;
-	case UART_MC_CLS_CHARLEN_6:
-		*bits = 6;
-		break;
-	case UART_MC_CLS_CHARLEN_7:
-		*bits = 7;
-		break;
-	case UART_MC_CLS_CHARLEN_8:
-		*bits = 8;
-		break;
-	}
-	quot = UART_GET_DIV_LO(port) | (UART_GET_DIV_HI(port) << 8);
-	*baud = port->uartclk / (16 *quot );
-}
-
-static int __init uart00_console_setup(struct console *co, char *options)
-{
-	struct uart_port *port;
-	int baud = 115200;
-	int bits = 8;
-	int parity = 'n';
-	int flow = 'n';
-
-#ifdef CONFIG_ARCH_CAMELOT
-	port = &epxa10db_port;             ;
-#else
-	return -ENODEV;
-#endif
-	if (options)
-		uart_parse_options(options, &baud, &parity, &bits, &flow);
-	else
-		uart00_console_get_options(port, &baud, &parity, &bits);
-
-	return uart_set_options(port, co, baud, parity, bits, flow);
-}
-
-extern struct uart_driver uart00_reg;
-static struct console uart00_console = {
-	.name		= SERIAL_UART00_NAME,
-	.write		= uart00_console_write,
-	.device		= uart_console_device,
-	.setup		= uart00_console_setup,
-	.flags		= CON_PRINTBUFFER,
-	.index		= 0,
-	.data		= &uart00_reg,
-};
-
-static int __init uart00_console_init(void)
-{
-	register_console(&uart00_console);
-	return 0;
-}
-console_initcall(uart00_console_init);
-
-#define UART00_CONSOLE	&uart00_console
-#else
-#define UART00_CONSOLE	NULL
-#endif
-
-static struct uart_driver uart00_reg = {
-	.owner			= NULL,
-	.driver_name		= SERIAL_UART00_NAME,
-	.dev_name		= SERIAL_UART00_NAME,
-	.major			= SERIAL_UART00_MAJOR,
-	.minor			= SERIAL_UART00_MINOR,
-	.nr			= UART_NR,
-	.cons			= UART00_CONSOLE,
-};
-
-struct dev_port_entry{
-	unsigned int base_addr;
-	struct uart_port *port;
-};
-
-#ifdef CONFIG_PLD_HOTSWAP
-
-static struct dev_port_entry dev_port_map[UART_NR];
-
-/*
- * Keep a mapping of dev_info addresses -> port lines to use when
- * removing ports dev==NULL indicates unused entry
- */
-
-struct uart00_ps_data{
-	unsigned int clk;
-	unsigned int fifosize;
-};
-
-int uart00_add_device(struct pldhs_dev_info* dev_info, void* dev_ps_data)
-{
-	struct uart00_ps_data* dev_ps=dev_ps_data;
-	struct uart_port * port;
-	int i,result;
-
-	i=0;
-	while(dev_port_map[i].port)
-		i++;
-
-	if(i==UART_NR){
-		printk(KERN_WARNING "uart00: Maximum number of ports reached\n");
-		return 0;
-	}
-
-	port=kmalloc(sizeof(struct uart_port),GFP_KERNEL);
-	if(!port)
-		return -ENOMEM;
-
-	printk("clk=%d fifo=%d\n",dev_ps->clk,dev_ps->fifosize);
-	port->membase=0;
-	port->mapbase=dev_info->base_addr;
-	port->iotype=SERIAL_IO_MEM;
-	port->irq=dev_info->irq;
-	port->uartclk=dev_ps->clk;
-	port->fifosize=dev_ps->fifosize;
-	port->ops=&uart00_pops;
-	port->line=i;
-	port->flags=ASYNC_BOOT_AUTOCONF;
-
-	result=uart_add_one_port(&uart00_reg, port);
-	if(result){
-		printk("uart_add_one_port returned %d\n",result);
-		return result;
-	}
-	dev_port_map[i].base_addr=dev_info->base_addr;
-	dev_port_map[i].port=port;
-	printk("uart00: added device at %x as ttyUA%d\n",dev_port_map[i].base_addr,i);
-	return 0;
-
-}
-
-int uart00_remove_devices(void)
-{
-	int i,result;
-
-
-	result=0;
-	for(i=1;i<UART_NR;i++){
-		if(dev_port_map[i].base_addr){
-			result=uart_remove_one_port(&uart00_reg, dev_port_map[i].port);
-			if(result)
-				return result;
-
-			/* port removed sucessfully, so now tidy up */
-			kfree(dev_port_map[i].port);
-			dev_port_map[i].base_addr=0;
-			dev_port_map[i].port=NULL;
-		}
-	}
-	return 0;
-
-}
-
-struct pld_hotswap_ops uart00_pldhs_ops={
-	.name		= "uart00",
-	.add_device	= uart00_add_device,
-	.remove_devices	= uart00_remove_devices,
-};
-
-#endif
-
-static int __init uart00_init(void)
-{
-	int result;
-
-	printk(KERN_INFO "Serial: UART00 driver $Revision: 1.35 $\n");
-
-	printk(KERN_WARNING "serial_uart00:Using temporary major/minor pairs"
-		" - these WILL change in the future\n");
-
-	result = uart_register_driver(&uart00_reg);
-	if (result)
-		return result;
-#ifdef CONFIG_ARCH_CAMELOT
-	result = uart_add_one_port(&uart00_reg,&epxa10db_port);
-#endif
-	if (result)
-		uart_unregister_driver(&uart00_reg);
-
-#ifdef  CONFIG_PLD_HOTSWAP
-	pldhs_register_driver(&uart00_pldhs_ops);
-#endif
-	return result;
-}
-
-__initcall(uart00_init);
diff --git a/drivers/video/cyber2000fb.c b/drivers/video/cyber2000fb.c
index a9300f9..55a3514 100644
--- a/drivers/video/cyber2000fb.c
+++ b/drivers/video/cyber2000fb.c
@@ -50,7 +50,6 @@
 #include <linux/init.h>
 
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/pgtable.h>
 #include <asm/system.h>
 #include <asm/uaccess.h>
diff --git a/drivers/video/sa1100fb.c b/drivers/video/sa1100fb.c
index 2ea1354..087e586 100644
--- a/drivers/video/sa1100fb.c
+++ b/drivers/video/sa1100fb.c
@@ -178,7 +178,6 @@
 
 #include <asm/hardware.h>
 #include <asm/io.h>
-#include <asm/irq.h>
 #include <asm/mach-types.h>
 #include <asm/uaccess.h>
 #include <asm/arch/assabet.h>
@@ -1455,7 +1454,11 @@ static struct sa1100fb_info * __init sa1100fb_init_fbinfo(struct device *dev)
 static int __init sa1100fb_probe(struct platform_device *pdev)
 {
 	struct sa1100fb_info *fbi;
-	int ret;
+	int ret, irq;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0)
+		return -EINVAL;
 
 	if (!request_mem_region(0xb0100000, 0x10000, "LCD"))
 		return -EBUSY;
@@ -1470,7 +1473,7 @@ static int __init sa1100fb_probe(struct platform_device *pdev)
 	if (ret)
 		goto failed;
 
-	ret = request_irq(IRQ_LCD, sa1100fb_handle_irq, SA_INTERRUPT,
+	ret = request_irq(irq, sa1100fb_handle_irq, SA_INTERRUPT,
 			  "LCD", fbi);
 	if (ret) {
 		printk(KERN_ERR "sa1100fb: request_irq failed: %d\n", ret);
@@ -1492,7 +1495,7 @@ static int __init sa1100fb_probe(struct platform_device *pdev)
 
 	ret = register_framebuffer(&fbi->fb);
 	if (ret < 0)
-		goto failed;
+		goto err_free_irq;
 
 #ifdef CONFIG_CPU_FREQ
 	fbi->freq_transition.notifier_call = sa1100fb_freq_transition;
@@ -1504,7 +1507,9 @@ static int __init sa1100fb_probe(struct platform_device *pdev)
 	/* This driver cannot be unloaded at the moment */
 	return 0;
 
-failed:
+ err_free_irq:
+	free_irq(irq, fbi);
+ failed:
 	platform_set_drvdata(pdev, NULL);
 	kfree(fbi);
 	release_mem_region(0xb0100000, 0x10000);