USB: ftdi_sio: checkpatch cleanups

Minor whitespace cleanups to make checkpatch happy.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

3 files changed, 88 insertions, 82 deletions

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 00b938a..97f2d9c 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -61,7 +61,7 @@ static __u16 product;
 
 struct ftdi_private {
 	struct kref kref;
-	ftdi_chip_type_t chip_type;
+	enum ftdi_chip_type chip_type;
 				/* type of device, either SIO or FT8U232AM */
 	int baud_base;		/* baud base clock for divisor setting */
 	int custom_divisor;	/* custom_divisor kludge, this is for
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index ff9bf80..213fe3d 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -23,14 +23,16 @@
  */
 
 /* Commands */
-#define FTDI_SIO_RESET 		0 /* Reset the port */
-#define FTDI_SIO_MODEM_CTRL 	1 /* Set the modem control register */
-#define FTDI_SIO_SET_FLOW_CTRL	2 /* Set flow control register */
-#define FTDI_SIO_SET_BAUD_RATE	3 /* Set baud rate */
-#define FTDI_SIO_SET_DATA	4 /* Set the data characteristics of the port */
-#define FTDI_SIO_GET_MODEM_STATUS	5 /* Retrieve current value of modem status register */
-#define FTDI_SIO_SET_EVENT_CHAR	6 /* Set the event character */
-#define FTDI_SIO_SET_ERROR_CHAR	7 /* Set the error character */
+#define FTDI_SIO_RESET			0 /* Reset the port */
+#define FTDI_SIO_MODEM_CTRL		1 /* Set the modem control register */
+#define FTDI_SIO_SET_FLOW_CTRL		2 /* Set flow control register */
+#define FTDI_SIO_SET_BAUD_RATE		3 /* Set baud rate */
+#define FTDI_SIO_SET_DATA		4 /* Set the data characteristics of
+					     the port */
+#define FTDI_SIO_GET_MODEM_STATUS	5 /* Retrieve current value of modem
+					     status register */
+#define FTDI_SIO_SET_EVENT_CHAR		6 /* Set the event character */
+#define FTDI_SIO_SET_ERROR_CHAR		7 /* Set the error character */
 #define FTDI_SIO_SET_LATENCY_TIMER	9 /* Set the latency timer */
 #define FTDI_SIO_GET_LATENCY_TIMER	10 /* Get the latency timer */
 
@@ -52,7 +54,7 @@
  */
 
 /* Port Identifier Table */
-#define PIT_DEFAULT 		0 /* SIOA */
+#define PIT_DEFAULT		0 /* SIOA */
 #define PIT_SIOA		1 /* SIOA */
 /* The device this driver is tested with one has only one port */
 #define PIT_SIOB		2 /* SIOB */
@@ -103,20 +105,21 @@
  * wLength:        0
  * Data:           None
  * The BaudDivisor values are calculated as follows:
- * - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
- *   I knew how to detect old chips to select proper base clock!
+ * - BaseClock is either 12000000 or 48000000 depending on the device.
+ *   FIXME: I wish I knew how to detect old chips to select proper base clock!
  * - BaudDivisor is a fixed point number encoded in a funny way.
  *   (--WRONG WAY OF THINKING--)
  *   BaudDivisor is a fixed point number encoded with following bit weighs:
  *   (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
  *   end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
  *   (--THE REALITY--)
- *   The both-bits-set has quite different meaning from 0.75 - the chip designers
- *   have decided it to mean 0.125 instead of 0.75.
+ *   The both-bits-set has quite different meaning from 0.75 - the chip
+ *   designers have decided it to mean 0.125 instead of 0.75.
  *   This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
  *   and Flow Control Consideration for USB to RS232".
  * - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
- *   automagically re-encode the resulting value to take fractions into consideration.
+ *   automagically re-encode the resulting value to take fractions into
+ *   consideration.
  * As all values are integers, some bit twiddling is in order:
  *   BaudDivisor = (BaseClock / 16 / BaudRate) |
  *   (((BaseClock / 2 / BaudRate) & 4) ? 0x4000    // 0.5
@@ -146,7 +149,7 @@
  * not supported by the FT8U232AM).
  */
 
-typedef enum {
+enum ftdi_chip_type {
 	SIO = 1,
 	FT8U232AM = 2,
 	FT232BM = 3,
@@ -154,37 +157,36 @@ typedef enum {
 	FT232RL = 5,
 	FT2232H = 6,
 	FT4232H = 7
-} ftdi_chip_type_t;
-
-typedef enum {
- ftdi_sio_b300 = 0,
- ftdi_sio_b600 = 1,
- ftdi_sio_b1200 = 2,
- ftdi_sio_b2400 = 3,
- ftdi_sio_b4800 = 4,
- ftdi_sio_b9600 = 5,
- ftdi_sio_b19200 = 6,
- ftdi_sio_b38400 = 7,
- ftdi_sio_b57600 = 8,
- ftdi_sio_b115200 = 9
-} FTDI_SIO_baudrate_t;
+};
+
+enum ftdi_sio_baudrate {
+	ftdi_sio_b300 = 0,
+	ftdi_sio_b600 = 1,
+	ftdi_sio_b1200 = 2,
+	ftdi_sio_b2400 = 3,
+	ftdi_sio_b4800 = 4,
+	ftdi_sio_b9600 = 5,
+	ftdi_sio_b19200 = 6,
+	ftdi_sio_b38400 = 7,
+	ftdi_sio_b57600 = 8,
+	ftdi_sio_b115200 = 9
+};
 
 /*
- * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
- * are calculated internally.
+ * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor
+ * values are calculated internally.
  */
-
-#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
-#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
-#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8)
-#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11)
-#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11)
-#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11)
-#define FTDI_SIO_SET_BREAK (0x1 << 14)
+#define FTDI_SIO_SET_DATA_REQUEST	FTDI_SIO_SET_DATA
+#define FTDI_SIO_SET_DATA_REQUEST_TYPE	0x40
+#define FTDI_SIO_SET_DATA_PARITY_NONE	(0x0 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_ODD	(0x1 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_EVEN	(0x2 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_MARK	(0x3 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_SPACE	(0x4 << 8)
+#define FTDI_SIO_SET_DATA_STOP_BITS_1	(0x0 << 11)
+#define FTDI_SIO_SET_DATA_STOP_BITS_15	(0x1 << 11)
+#define FTDI_SIO_SET_DATA_STOP_BITS_2	(0x2 << 11)
+#define FTDI_SIO_SET_BREAK		(0x1 << 14)
 /* FTDI_SIO_SET_DATA */
 
 /*
@@ -287,8 +289,8 @@ typedef enum {
  *
  * A value of zero in the hIndex field disables handshaking
  *
- * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character
- * and the lValue field contains the XON character.
+ * If Xon/Xoff handshaking is specified, the hValue field should contain the
+ * XOFF character and the lValue field contains the XON character.
  */
 
 /*
@@ -373,7 +375,10 @@ typedef enum {
 
 /* FTDI_SIO_SET_ERROR_CHAR */
 
-/* Set the parity error replacement character for the specified communications port */
+/*
+ * Set the parity error replacement character for the specified communications
+ * port
+ */
 
 /*
  *  BmRequestType:  0100 0000b
@@ -496,9 +501,10 @@ typedef enum {
  *
  * IN Endpoint
  *
- * The device reserves the first two bytes of data on this endpoint to contain the current
- * values of the modem and line status registers. In the absence of data, the device 
- * generates a message consisting of these two status bytes every 40 ms
+ * The device reserves the first two bytes of data on this endpoint to contain
+ * the current values of the modem and line status registers. In the absence of
+ * data, the device generates a message consisting of these two status bytes
+ * every 40 ms
  *
  * Byte 0: Modem Status
  *
@@ -530,21 +536,21 @@ typedef enum {
 #define FTDI_RS0_RI	(1 << 6)
 #define FTDI_RS0_RLSD	(1 << 7)
 
-#define FTDI_RS_DR  1
-#define FTDI_RS_OE (1<<1)
-#define FTDI_RS_PE (1<<2)
-#define FTDI_RS_FE (1<<3)
-#define FTDI_RS_BI (1<<4)
-#define FTDI_RS_THRE (1<<5)
-#define FTDI_RS_TEMT (1<<6)
-#define FTDI_RS_FIFO  (1<<7)
+#define FTDI_RS_DR	1
+#define FTDI_RS_OE	(1<<1)
+#define FTDI_RS_PE	(1<<2)
+#define FTDI_RS_FE	(1<<3)
+#define FTDI_RS_BI	(1<<4)
+#define FTDI_RS_THRE	(1<<5)
+#define FTDI_RS_TEMT	(1<<6)
+#define FTDI_RS_FIFO	(1<<7)
 
 /*
  * OUT Endpoint
  *
- * This device reserves the first bytes of data on this endpoint contain the length
- * and port identifier of the message. For the FTDI USB Serial converter the port 
- * identifier is always 1.
+ * This device reserves the first bytes of data on this endpoint contain the
+ * length and port identifier of the message. For the FTDI USB Serial converter
+ * the port identifier is always 1.
  *
  * Byte 0: Line Status
  *
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 75482cb..94d86c3 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -275,8 +275,8 @@
 /*
  * Hameg HO820 and HO870 interface (using VID 0x0403)
  */
-#define        HAMEG_HO820_PID         0xed74
-#define        HAMEG_HO870_PID         0xed71
+#define HAMEG_HO820_PID			0xed74
+#define HAMEG_HO870_PID			0xed71
 
 /*
  *  MaxStream devices	www.maxstream.net
@@ -289,14 +289,14 @@
  * and Mike Studer (K6EEP) <k6eep@hamsoftware.org>.
  * Ian Abbott <abbotti@mev.co.uk> added a few more from the driver INF file.
  */
-#define FTDI_MHAM_KW_PID 0xEEE8		/* USB-KW interface */
-#define FTDI_MHAM_YS_PID 0xEEE9		/* USB-YS interface */
-#define FTDI_MHAM_Y6_PID 0xEEEA		/* USB-Y6 interface */
-#define FTDI_MHAM_Y8_PID 0xEEEB		/* USB-Y8 interface */
-#define FTDI_MHAM_IC_PID 0xEEEC		/* USB-IC interface */
-#define FTDI_MHAM_DB9_PID 0xEEED	/* USB-DB9 interface */
-#define FTDI_MHAM_RS232_PID 0xEEEE	/* USB-RS232 interface */
-#define FTDI_MHAM_Y9_PID 0xEEEF		/* USB-Y9 interface */
+#define FTDI_MHAM_KW_PID	0xEEE8	/* USB-KW interface */
+#define FTDI_MHAM_YS_PID	0xEEE9	/* USB-YS interface */
+#define FTDI_MHAM_Y6_PID	0xEEEA	/* USB-Y6 interface */
+#define FTDI_MHAM_Y8_PID	0xEEEB	/* USB-Y8 interface */
+#define FTDI_MHAM_IC_PID	0xEEEC	/* USB-IC interface */
+#define FTDI_MHAM_DB9_PID	0xEEED	/* USB-DB9 interface */
+#define FTDI_MHAM_RS232_PID	0xEEEE	/* USB-RS232 interface */
+#define FTDI_MHAM_Y9_PID	0xEEEF	/* USB-Y9 interface */
 
 /* Domintell products  http://www.domintell.com */
 #define FTDI_DOMINTELL_DGQG_PID	0xEF50	/* Master */
@@ -483,9 +483,9 @@
  * Blackfin gnICE JTAG
  * http://docs.blackfin.uclinux.org/doku.php?id=hw:jtag:gnice
  */
-#define ADI_VID 		0x0456
-#define ADI_GNICE_PID 		0xF000
-#define ADI_GNICEPLUS_PID 	0xF001
+#define ADI_VID			0x0456
+#define ADI_GNICE_PID		0xF000
+#define ADI_GNICEPLUS_PID	0xF001
 
 /*
  * RATOC REX-USB60F
@@ -611,13 +611,13 @@
 #define SEALEVEL_2802_7_PID	0X2872	/* SeaLINK+8/485 (2802) Port 7 */
 #define SEALEVEL_2802_8_PID	0X2882	/* SeaLINK+8/485 (2802) Port 8 */
 #define SEALEVEL_2803_1_PID	0X2813	/* SeaLINK+8 (2803) Port 1 */
-#define SEALEVEL_2803_2_PID	0X2823 	/* SeaLINK+8 (2803) Port 2 */
-#define SEALEVEL_2803_3_PID	0X2833 	/* SeaLINK+8 (2803) Port 3 */
-#define SEALEVEL_2803_4_PID	0X2843 	/* SeaLINK+8 (2803) Port 4 */
-#define SEALEVEL_2803_5_PID	0X2853 	/* SeaLINK+8 (2803) Port 5 */
-#define SEALEVEL_2803_6_PID	0X2863 	/* SeaLINK+8 (2803) Port 6 */
-#define SEALEVEL_2803_7_PID	0X2873 	/* SeaLINK+8 (2803) Port 7 */
-#define SEALEVEL_2803_8_PID	0X2883 	/* SeaLINK+8 (2803) Port 8 */
+#define SEALEVEL_2803_2_PID	0X2823	/* SeaLINK+8 (2803) Port 2 */
+#define SEALEVEL_2803_3_PID	0X2833	/* SeaLINK+8 (2803) Port 3 */
+#define SEALEVEL_2803_4_PID	0X2843	/* SeaLINK+8 (2803) Port 4 */
+#define SEALEVEL_2803_5_PID	0X2853	/* SeaLINK+8 (2803) Port 5 */
+#define SEALEVEL_2803_6_PID	0X2863	/* SeaLINK+8 (2803) Port 6 */
+#define SEALEVEL_2803_7_PID	0X2873	/* SeaLINK+8 (2803) Port 7 */
+#define SEALEVEL_2803_8_PID	0X2883	/* SeaLINK+8 (2803) Port 8 */
 
 /*
  * JETI SPECTROMETER SPECBOS 1201
@@ -1013,7 +1013,7 @@
  */
 #define EVOLUTION_VID		0xDEEE	/* Vendor ID */
 #define EVOLUTION_ER1_PID	0x0300	/* ER1 Control Module */
-#define EVO_8U232AM_PID	0x02FF	/* Evolution robotics RCM2 (FT232AM)*/
+#define EVO_8U232AM_PID		0x02FF	/* Evolution robotics RCM2 (FT232AM)*/
 #define EVO_HYBRID_PID		0x0302	/* Evolution robotics RCM4 PID (FT232BM)*/
 #define EVO_RCM4_PID		0x0303	/* Evolution robotics RCM4 PID */