Merge branch 'omap3-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel

107 files changed, 1099 insertions, 712 deletions

diff --git a/drivers/acpi/battery.c b/drivers/acpi/battery.c
index a0a178d..1423b0c 100644
--- a/drivers/acpi/battery.c
+++ b/drivers/acpi/battery.c
@@ -174,15 +174,6 @@ static int acpi_battery_get_property(struct power_supply *psy,
 		break;
 	case POWER_SUPPLY_PROP_CURRENT_NOW:
 		val->intval = battery->current_now * 1000;
-		/* if power units are mW, convert to mA by
-		   dividing by current voltage (mV/1000) */
-		if (!battery->power_unit) {
-			if (battery->voltage_now) {
-				val->intval /= battery->voltage_now;
-				val->intval *= 1000;
-			} else
-				val->intval = -1;
-		}
 		break;
 	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
 	case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN:
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 78fbec8..421b7c7 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -153,7 +153,7 @@ config SATA_PROMISE
 	  If unsure, say N.
 
 config SATA_SX4
-	tristate "Promise SATA SX4 support"
+	tristate "Promise SATA SX4 support (Experimental)"
 	depends on PCI && EXPERIMENTAL
 	help
 	  This option enables support for Promise Serial ATA SX4.
@@ -219,8 +219,8 @@ config PATA_ACPI
 	  otherwise unsupported hardware.
 
 config PATA_ALI
-	tristate "ALi PATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "ALi PATA support"
+	depends on PCI
 	help
 	  This option enables support for the ALi ATA interfaces
 	  found on the many ALi chipsets.
@@ -263,7 +263,7 @@ config PATA_ATIIXP
 	  If unsure, say N.
 
 config PATA_CMD640_PCI
-	tristate "CMD640 PCI PATA support (Very Experimental)"
+	tristate "CMD640 PCI PATA support (Experimental)"
 	depends on PCI && EXPERIMENTAL
 	help
 	  This option enables support for the CMD640 PCI IDE
@@ -291,8 +291,8 @@ config PATA_CS5520
 	  If unsure, say N.
 
 config PATA_CS5530
-	tristate "CS5530 PATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "CS5530 PATA support"
+	depends on PCI
 	help
 	  This option enables support for the Cyrix/NatSemi/AMD CS5530
 	  companion chip used with the MediaGX/Geode processor family.
@@ -309,8 +309,8 @@ config PATA_CS5535
 	  If unsure, say N.
 
 config PATA_CS5536
-	tristate "CS5536 PATA support (Experimental)"
-	depends on PCI && X86 && !X86_64 && EXPERIMENTAL
+	tristate "CS5536 PATA support"
+	depends on PCI && X86 && !X86_64
 	help
 	  This option enables support for the AMD CS5536
 	  companion chip used with the Geode LX processor family.
@@ -363,7 +363,7 @@ config PATA_HPT37X
 	  If unsure, say N.
 
 config PATA_HPT3X2N
-	tristate "HPT 372N/302N PATA support (Very Experimental)"
+	tristate "HPT 372N/302N PATA support (Experimental)"
 	depends on PCI && EXPERIMENTAL
 	help
 	  This option enables support for the N variant HPT PATA
@@ -389,8 +389,8 @@ config PATA_HPT3X3_DMA
 	  problems with DMA on this chipset.
 
 config PATA_ISAPNP
-	tristate "ISA Plug and Play PATA support (Experimental)"
-	depends on EXPERIMENTAL && ISAPNP
+	tristate "ISA Plug and Play PATA support"
+	depends on ISAPNP
 	help
 	  This option enables support for ISA plug & play ATA
 	  controllers such as those found on old soundcards.
@@ -498,8 +498,8 @@ config PATA_NINJA32
 	  If unsure, say N.
 
 config PATA_NS87410
-	tristate "Nat Semi NS87410 PATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "Nat Semi NS87410 PATA support"
+	depends on PCI
 	help
 	  This option enables support for the National Semiconductor
 	  NS87410 PCI-IDE controller.
@@ -507,8 +507,8 @@ config PATA_NS87410
 	  If unsure, say N.
 
 config PATA_NS87415
-	tristate "Nat Semi NS87415 PATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "Nat Semi NS87415 PATA support"
+	depends on PCI
 	help
 	  This option enables support for the National Semiconductor
 	  NS87415 PCI-IDE controller.
@@ -544,8 +544,8 @@ config PATA_PCMCIA
 	  If unsure, say N.
 
 config PATA_PDC_OLD
-	tristate "Older Promise PATA controller support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "Older Promise PATA controller support"
+	depends on PCI
 	help
 	  This option enables support for the Promise 20246, 20262, 20263,
 	  20265 and 20267 adapters.
@@ -559,7 +559,7 @@ config PATA_QDI
 	  Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
 
 config PATA_RADISYS
-	tristate "RADISYS 82600 PATA support (Very Experimental)"
+	tristate "RADISYS 82600 PATA support (Experimental)"
 	depends on PCI && EXPERIMENTAL
 	help
 	  This option enables support for the RADISYS 82600
@@ -586,8 +586,8 @@ config PATA_RZ1000
 	  If unsure, say N.
 
 config PATA_SC1200
-	tristate "SC1200 PATA support (Very Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "SC1200 PATA support"
+	depends on PCI
 	help
 	  This option enables support for the NatSemi/AMD SC1200 SoC
 	  companion chip used with the Geode processor family.
@@ -620,8 +620,8 @@ config PATA_SIL680
 	  If unsure, say N.
 
 config PATA_SIS
-	tristate "SiS PATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "SiS PATA support"
+	depends on PCI
 	help
 	  This option enables support for SiS PATA controllers
 
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index d6d97d8..c11936e 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -1072,7 +1072,14 @@ static int piix_broken_suspend(void)
 	 * matching is necessary because dmi_system_id.matches is
 	 * limited to four entries.
 	 */
-	if (!strcmp(dmi_get_system_info(DMI_SYS_VENDOR), "TOSHIBA") &&
+	if (dmi_get_system_info(DMI_SYS_VENDOR) &&
+	    dmi_get_system_info(DMI_PRODUCT_NAME) &&
+	    dmi_get_system_info(DMI_PRODUCT_VERSION) &&
+	    dmi_get_system_info(DMI_PRODUCT_SERIAL) &&
+	    dmi_get_system_info(DMI_BOARD_VENDOR) &&
+	    dmi_get_system_info(DMI_BOARD_NAME) &&
+	    dmi_get_system_info(DMI_BOARD_VERSION) &&
+	    !strcmp(dmi_get_system_info(DMI_SYS_VENDOR), "TOSHIBA") &&
 	    !strcmp(dmi_get_system_info(DMI_PRODUCT_NAME), "000000") &&
 	    !strcmp(dmi_get_system_info(DMI_PRODUCT_VERSION), "000000") &&
 	    !strcmp(dmi_get_system_info(DMI_PRODUCT_SERIAL), "000000") &&
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index f2b83ea..a098ba8 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -382,10 +382,10 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	/* PCI clocking determines the ATA timing values to use */
 	/* info_hpt366 is safe against re-entry so we can scribble on it */
 	switch((reg1 & 0x700) >> 8) {
-		case 5:
+		case 9:
 			hpriv = &hpt366_40;
 			break;
-		case 9:
+		case 5:
 			hpriv = &hpt366_25;
 			break;
 		default:
diff --git a/drivers/ata/pata_ninja32.c b/drivers/ata/pata_ninja32.c
index 4e466ea..4dd9a3b 100644
--- a/drivers/ata/pata_ninja32.c
+++ b/drivers/ata/pata_ninja32.c
@@ -44,7 +44,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_ninja32"
-#define DRV_VERSION "0.1.1"
+#define DRV_VERSION "0.1.3"
 
 
 /**
@@ -130,7 +130,8 @@ static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 		return rc;
 	pci_set_master(dev);
 
-	/* Set up the register mappings */
+	/* Set up the register mappings. We use the I/O mapping as only the
+	   older chips also have MMIO on BAR 1 */
 	base = host->iomap[0];
 	if (!base)
 		return -ENOMEM;
@@ -167,8 +168,12 @@ static int ninja32_reinit_one(struct pci_dev *pdev)
 #endif
 
 static const struct pci_device_id ninja32[] = {
+	{ 0x10FC, 0x0003, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+	{ 0x1145, 0x8008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+	{ 0x1145, 0xf008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
 	{ 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
 	{ 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+	{ 0x1145, 0xf02C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
 	{ },
 };
 
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index d342366..e4be55e 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -56,7 +56,6 @@ static const struct sis_laptop sis_laptop[] = {
 	{ 0x5513, 0x1043, 0x1107 },	/* ASUS A6K */
 	{ 0x5513, 0x1734, 0x105F },	/* FSC Amilo A1630 */
 	{ 0x5513, 0x1071, 0x8640 },     /* EasyNote K5305 */
-	{ 0x5513, 0x1039, 0x5513 },	/* Targa Visionary 1000 */
 	/* end marker */
 	{ 0, }
 };
diff --git a/drivers/atm/horizon.c b/drivers/atm/horizon.c
index 6154123..6b969f8 100644
--- a/drivers/atm/horizon.c
+++ b/drivers/atm/horizon.c
@@ -2705,7 +2705,7 @@ static int __devinit hrz_probe(struct pci_dev *pci_dev, const struct pci_device_
 
 	/* XXX DEV_LABEL is a guess */
 	if (!request_region(iobase, HRZ_IO_EXTENT, DEV_LABEL)) {
-		return -EINVAL;
+		err = -EINVAL;
 		goto out_disable;
 	}
 
diff --git a/drivers/block/pktcdvd.c b/drivers/block/pktcdvd.c
index f20bf35..dc7a8c3 100644
--- a/drivers/block/pktcdvd.c
+++ b/drivers/block/pktcdvd.c
@@ -302,7 +302,7 @@ static struct kobj_type kobj_pkt_type_wqueue = {
 static void pkt_sysfs_dev_new(struct pktcdvd_device *pd)
 {
 	if (class_pktcdvd) {
-		pd->dev = device_create(class_pktcdvd, NULL, pd->pkt_dev, NULL,
+		pd->dev = device_create(class_pktcdvd, NULL, MKDEV(0, 0), NULL,
 					"%s", pd->name);
 		if (IS_ERR(pd->dev))
 			pd->dev = NULL;
@@ -2790,7 +2790,7 @@ static int pkt_new_dev(struct pktcdvd_device *pd, dev_t dev)
 	return 0;
 
 out_mem:
-	blkdev_put(bdev, FMODE_READ|FMODE_WRITE);
+	blkdev_put(bdev, FMODE_READ | FMODE_NDELAY);
 	/* This is safe: open() is still holding a reference. */
 	module_put(THIS_MODULE);
 	return ret;
@@ -2975,7 +2975,7 @@ static int pkt_remove_dev(dev_t pkt_dev)
 	pkt_debugfs_dev_remove(pd);
 	pkt_sysfs_dev_remove(pd);
 
-	blkdev_put(pd->bdev, FMODE_READ|FMODE_WRITE);
+	blkdev_put(pd->bdev, FMODE_READ | FMODE_NDELAY);
 
 	remove_proc_entry(pd->name, pkt_proc);
 	DPRINTK(DRIVER_NAME": writer %s unmapped\n", pd->name);
diff --git a/drivers/char/serial167.c b/drivers/char/serial167.c
index 3b23270..a8f15e6 100644
--- a/drivers/char/serial167.c
+++ b/drivers/char/serial167.c
@@ -418,7 +418,7 @@ static irqreturn_t cd2401_rxerr_interrupt(int irq, void *dev_id)
 							     TTY_OVERRUN);
 					/*
 					   If the flip buffer itself is
-					   overflowing, we still loose
+					   overflowing, we still lose
 					   the next incoming character.
 					 */
 					if (tty_buffer_request_room(tty, 1) !=
diff --git a/drivers/firewire/fw-ohci.c b/drivers/firewire/fw-ohci.c
index 46610b0..ab9c01e 100644
--- a/drivers/firewire/fw-ohci.c
+++ b/drivers/firewire/fw-ohci.c
@@ -974,6 +974,7 @@ at_context_queue_packet(struct context *ctx, struct fw_packet *packet)
 			packet->ack = RCODE_SEND_ERROR;
 			return -1;
 		}
+		packet->payload_bus = payload_bus;
 
 		d[2].req_count    = cpu_to_le16(packet->payload_length);
 		d[2].data_address = cpu_to_le32(payload_bus);
@@ -1025,7 +1026,6 @@ static int handle_at_packet(struct context *context,
 	struct driver_data *driver_data;
 	struct fw_packet *packet;
 	struct fw_ohci *ohci = context->ohci;
-	dma_addr_t payload_bus;
 	int evt;
 
 	if (last->transfer_status == 0)
@@ -1038,9 +1038,8 @@ static int handle_at_packet(struct context *context,
 		/* This packet was cancelled, just continue. */
 		return 1;
 
-	payload_bus = le32_to_cpu(last->data_address);
-	if (payload_bus != 0)
-		dma_unmap_single(ohci->card.device, payload_bus,
+	if (packet->payload_bus)
+		dma_unmap_single(ohci->card.device, packet->payload_bus,
 				 packet->payload_length, DMA_TO_DEVICE);
 
 	evt = le16_to_cpu(last->transfer_status) & 0x1f;
@@ -1697,6 +1696,10 @@ static int ohci_cancel_packet(struct fw_card *card, struct fw_packet *packet)
 	if (packet->ack != 0)
 		goto out;
 
+	if (packet->payload_bus)
+		dma_unmap_single(ohci->card.device, packet->payload_bus,
+				 packet->payload_length, DMA_TO_DEVICE);
+
 	log_ar_at_event('T', packet->speed, packet->header, 0x20);
 	driver_data->packet = NULL;
 	packet->ack = RCODE_CANCELLED;
diff --git a/drivers/firewire/fw-transaction.c b/drivers/firewire/fw-transaction.c
index 022ac4f..2884f87 100644
--- a/drivers/firewire/fw-transaction.c
+++ b/drivers/firewire/fw-transaction.c
@@ -207,6 +207,7 @@ fw_fill_request(struct fw_packet *packet, int tcode, int tlabel,
 	packet->speed = speed;
 	packet->generation = generation;
 	packet->ack = 0;
+	packet->payload_bus = 0;
 }
 
 /**
@@ -581,6 +582,8 @@ fw_fill_response(struct fw_packet *response, u32 *request_header,
 		BUG();
 		return;
 	}
+
+	response->payload_bus = 0;
 }
 EXPORT_SYMBOL(fw_fill_response);
 
diff --git a/drivers/firewire/fw-transaction.h b/drivers/firewire/fw-transaction.h
index aed7dbb..839466f0 100644
--- a/drivers/firewire/fw-transaction.h
+++ b/drivers/firewire/fw-transaction.h
@@ -27,6 +27,7 @@
 #include <linux/list.h>
 #include <linux/spinlock_types.h>
 #include <linux/timer.h>
+#include <linux/types.h>
 #include <linux/workqueue.h>
 
 #define TCODE_IS_READ_REQUEST(tcode)	(((tcode) & ~1) == 4)
@@ -153,6 +154,7 @@ struct fw_packet {
 	size_t header_length;
 	void *payload;
 	size_t payload_length;
+	dma_addr_t payload_bus;
 	u32 timestamp;
 
 	/*
diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
index ba89b42..553dd4b 100644
--- a/drivers/gpu/drm/i915/i915_dma.c
+++ b/drivers/gpu/drm/i915/i915_dma.c
@@ -847,9 +847,10 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	 * and the registers being closely associated.
 	 *
 	 * According to chipset errata, on the 965GM, MSI interrupts may
-	 * be lost or delayed
+	 * be lost or delayed, but we use them anyways to avoid
+	 * stuck interrupts on some machines.
 	 */
-	if (!IS_I945G(dev) && !IS_I945GM(dev) && !IS_I965GM(dev))
+	if (!IS_I945G(dev) && !IS_I945GM(dev))
 		pci_enable_msi(dev->pdev);
 
 	intel_opregion_init(dev);
diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 0a4f39b..adc972cc 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -244,6 +244,10 @@ typedef struct drm_i915_private {
 		 * List of objects currently involved in rendering from the
 		 * ringbuffer.
 		 *
+		 * Includes buffers having the contents of their GPU caches
+		 * flushed, not necessarily primitives.  last_rendering_seqno
+		 * represents when the rendering involved will be completed.
+		 *
 		 * A reference is held on the buffer while on this list.
 		 */
 		struct list_head active_list;
@@ -253,6 +257,8 @@ typedef struct drm_i915_private {
 		 * still have a write_domain which needs to be flushed before
 		 * unbinding.
 		 *
+		 * last_rendering_seqno is 0 while an object is in this list.
+		 *
 		 * A reference is held on the buffer while on this list.
 		 */
 		struct list_head flushing_list;
@@ -261,6 +267,8 @@ typedef struct drm_i915_private {
 		 * LRU list of objects which are not in the ringbuffer and
 		 * are ready to unbind, but are still in the GTT.
 		 *
+		 * last_rendering_seqno is 0 while an object is in this list.
+		 *
 		 * A reference is not held on the buffer while on this list,
 		 * as merely being GTT-bound shouldn't prevent its being
 		 * freed, and we'll pull it off the list in the free path.
@@ -371,8 +379,8 @@ struct drm_i915_gem_object {
 	uint32_t agp_type;
 
 	/**
-	 * Flagging of which individual pages are valid in GEM_DOMAIN_CPU when
-	 * GEM_DOMAIN_CPU is not in the object's read domain.
+	 * If present, while GEM_DOMAIN_CPU is in the read domain this array
+	 * flags which individual pages are valid.
 	 */
 	uint8_t *page_cpu_valid;
 };
@@ -394,9 +402,6 @@ struct drm_i915_gem_request {
 	/** Time at which this request was emitted, in jiffies. */
 	unsigned long emitted_jiffies;
 
-	/** Cache domains that were flushed at the start of the request. */
-	uint32_t flush_domains;
-
 	struct list_head list;
 };
 
diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c
index d58ddef..ad672d8 100644
--- a/drivers/gpu/drm/i915/i915_gem.c
+++ b/drivers/gpu/drm/i915/i915_gem.c
@@ -33,21 +33,21 @@
 
 #define I915_GEM_GPU_DOMAINS	(~(I915_GEM_DOMAIN_CPU | I915_GEM_DOMAIN_GTT))
 
-static int
-i915_gem_object_set_domain(struct drm_gem_object *obj,
-			    uint32_t read_domains,
-			    uint32_t write_domain);
-static int
-i915_gem_object_set_domain_range(struct drm_gem_object *obj,
-				 uint64_t offset,
-				 uint64_t size,
-				 uint32_t read_domains,
-				 uint32_t write_domain);
-static int
-i915_gem_set_domain(struct drm_gem_object *obj,
-		    struct drm_file *file_priv,
-		    uint32_t read_domains,
-		    uint32_t write_domain);
+static void
+i915_gem_object_set_to_gpu_domain(struct drm_gem_object *obj,
+				  uint32_t read_domains,
+				  uint32_t write_domain);
+static void i915_gem_object_flush_gpu_write_domain(struct drm_gem_object *obj);
+static void i915_gem_object_flush_gtt_write_domain(struct drm_gem_object *obj);
+static void i915_gem_object_flush_cpu_write_domain(struct drm_gem_object *obj);
+static int i915_gem_object_set_to_gtt_domain(struct drm_gem_object *obj,
+					     int write);
+static int i915_gem_object_set_to_cpu_domain(struct drm_gem_object *obj,
+					     int write);
+static int i915_gem_object_set_cpu_read_domain_range(struct drm_gem_object *obj,
+						     uint64_t offset,
+						     uint64_t size);
+static void i915_gem_object_set_to_full_cpu_read_domain(struct drm_gem_object *obj);
 static int i915_gem_object_get_page_list(struct drm_gem_object *obj);
 static void i915_gem_object_free_page_list(struct drm_gem_object *obj);
 static int i915_gem_object_wait_rendering(struct drm_gem_object *obj);
@@ -162,8 +162,8 @@ i915_gem_pread_ioctl(struct drm_device *dev, void *data,
 
 	mutex_lock(&dev->struct_mutex);
 
-	ret = i915_gem_object_set_domain_range(obj, args->offset, args->size,
-					       I915_GEM_DOMAIN_CPU, 0);
+	ret = i915_gem_object_set_cpu_read_domain_range(obj, args->offset,
+							args->size);
 	if (ret != 0) {
 		drm_gem_object_unreference(obj);
 		mutex_unlock(&dev->struct_mutex);
@@ -260,8 +260,7 @@ i915_gem_gtt_pwrite(struct drm_device *dev, struct drm_gem_object *obj,
 		mutex_unlock(&dev->struct_mutex);
 		return ret;
 	}
-	ret = i915_gem_set_domain(obj, file_priv,
-				  I915_GEM_DOMAIN_GTT, I915_GEM_DOMAIN_GTT);
+	ret = i915_gem_object_set_to_gtt_domain(obj, 1);
 	if (ret)
 		goto fail;
 
@@ -320,8 +319,7 @@ i915_gem_shmem_pwrite(struct drm_device *dev, struct drm_gem_object *obj,
 
 	mutex_lock(&dev->struct_mutex);
 
-	ret = i915_gem_set_domain(obj, file_priv,
-				  I915_GEM_DOMAIN_CPU, I915_GEM_DOMAIN_CPU);
+	ret = i915_gem_object_set_to_cpu_domain(obj, 1);
 	if (ret) {
 		mutex_unlock(&dev->struct_mutex);
 		return ret;
@@ -397,7 +395,8 @@ i915_gem_pwrite_ioctl(struct drm_device *dev, void *data,
 }
 
 /**
- * Called when user space prepares to use an object
+ * Called when user space prepares to use an object with the CPU, either
+ * through the mmap ioctl's mapping or a GTT mapping.
  */
 int
 i915_gem_set_domain_ioctl(struct drm_device *dev, void *data,
@@ -405,11 +404,26 @@ i915_gem_set_domain_ioctl(struct drm_device *dev, void *data,
 {
 	struct drm_i915_gem_set_domain *args = data;
 	struct drm_gem_object *obj;
+	uint32_t read_domains = args->read_domains;
+	uint32_t write_domain = args->write_domain;
 	int ret;
 
 	if (!(dev->driver->driver_features & DRIVER_GEM))
 		return -ENODEV;
 
+	/* Only handle setting domains to types used by the CPU. */
+	if (write_domain & ~(I915_GEM_DOMAIN_CPU | I915_GEM_DOMAIN_GTT))
+		return -EINVAL;
+
+	if (read_domains & ~(I915_GEM_DOMAIN_CPU | I915_GEM_DOMAIN_GTT))
+		return -EINVAL;
+
+	/* Having something in the write domain implies it's in the read
+	 * domain, and only that read domain.  Enforce that in the request.
+	 */
+	if (write_domain != 0 && read_domains != write_domain)
+		return -EINVAL;
+
 	obj = drm_gem_object_lookup(dev, file_priv, args->handle);
 	if (obj == NULL)
 		return -EBADF;
@@ -417,10 +431,21 @@ i915_gem_set_domain_ioctl(struct drm_device *dev, void *data,
 	mutex_lock(&dev->struct_mutex);
 #if WATCH_BUF
 	DRM_INFO("set_domain_ioctl %p(%d), %08x %08x\n",
-		 obj, obj->size, args->read_domains, args->write_domain);
+		 obj, obj->size, read_domains, write_domain);
 #endif
-	ret = i915_gem_set_domain(obj, file_priv,
-				  args->read_domains, args->write_domain);
+	if (read_domains & I915_GEM_DOMAIN_GTT) {
+		ret = i915_gem_object_set_to_gtt_domain(obj, write_domain != 0);
+
+		/* Silently promote "you're not bound, there was nothing to do"
+		 * to success, since the client was just asking us to
+		 * make sure everything was done.
+		 */
+		if (ret == -EINVAL)
+			ret = 0;
+	} else {
+		ret = i915_gem_object_set_to_cpu_domain(obj, write_domain != 0);
+	}
+
 	drm_gem_object_unreference(obj);
 	mutex_unlock(&dev->struct_mutex);
 	return ret;
@@ -455,10 +480,9 @@ i915_gem_sw_finish_ioctl(struct drm_device *dev, void *data,
 	obj_priv = obj->driver_private;
 
 	/* Pinned buffers may be scanout, so flush the cache */
-	if ((obj->write_domain & I915_GEM_DOMAIN_CPU) && obj_priv->pin_count) {
-		i915_gem_clflush_object(obj);
-		drm_agp_chipset_flush(dev);
-	}
+	if (obj_priv->pin_count)
+		i915_gem_object_flush_cpu_write_domain(obj);
+
 	drm_gem_object_unreference(obj);
 	mutex_unlock(&dev->struct_mutex);
 	return ret;
@@ -532,7 +556,7 @@ i915_gem_object_free_page_list(struct drm_gem_object *obj)
 }
 
 static void
-i915_gem_object_move_to_active(struct drm_gem_object *obj)
+i915_gem_object_move_to_active(struct drm_gem_object *obj, uint32_t seqno)
 {
 	struct drm_device *dev = obj->dev;
 	drm_i915_private_t *dev_priv = dev->dev_private;
@@ -546,8 +570,20 @@ i915_gem_object_move_to_active(struct drm_gem_object *obj)
 	/* Move from whatever list we were on to the tail of execution. */
 	list_move_tail(&obj_priv->list,
 		       &dev_priv->mm.active_list);
+	obj_priv->last_rendering_seqno = seqno;
 }
 
+static void
+i915_gem_object_move_to_flushing(struct drm_gem_object *obj)
+{
+	struct drm_device *dev = obj->dev;
+	drm_i915_private_t *dev_priv = dev->dev_private;
+	struct drm_i915_gem_object *obj_priv = obj->driver_private;
+
+	BUG_ON(!obj_priv->active);
+	list_move_tail(&obj_priv->list, &dev_priv->mm.flushing_list);
+	obj_priv->last_rendering_seqno = 0;
+}
 
 static void
 i915_gem_object_move_to_inactive(struct drm_gem_object *obj)
@@ -562,6 +598,7 @@ i915_gem_object_move_to_inactive(struct drm_gem_object *obj)
 	else
 		list_move_tail(&obj_priv->list, &dev_priv->mm.inactive_list);
 
+	obj_priv->last_rendering_seqno = 0;
 	if (obj_priv->active) {
 		obj_priv->active = 0;
 		drm_gem_object_unreference(obj);
@@ -610,10 +647,28 @@ i915_add_request(struct drm_device *dev, uint32_t flush_domains)
 
 	request->seqno = seqno;
 	request->emitted_jiffies = jiffies;
-	request->flush_domains = flush_domains;
 	was_empty = list_empty(&dev_priv->mm.request_list);
 	list_add_tail(&request->list, &dev_priv->mm.request_list);
 
+	/* Associate any objects on the flushing list matching the write
+	 * domain we're flushing with our flush.
+	 */
+	if (flush_domains != 0) {
+		struct drm_i915_gem_object *obj_priv, *next;
+
+		list_for_each_entry_safe(obj_priv, next,
+					 &dev_priv->mm.flushing_list, list) {
+			struct drm_gem_object *obj = obj_priv->obj;
+
+			if ((obj->write_domain & flush_domains) ==
+			    obj->write_domain) {
+				obj->write_domain = 0;
+				i915_gem_object_move_to_active(obj, seqno);
+			}
+		}
+
+	}
+
 	if (was_empty && !dev_priv->mm.suspended)
 		schedule_delayed_work(&dev_priv->mm.retire_work, HZ);
 	return seqno;
@@ -676,30 +731,10 @@ i915_gem_retire_request(struct drm_device *dev,
 			 __func__, request->seqno, obj);
 #endif
 
-		if (obj->write_domain != 0) {
-			list_move_tail(&obj_priv->list,
-				       &dev_priv->mm.flushing_list);
-		} else {
+		if (obj->write_domain != 0)
+			i915_gem_object_move_to_flushing(obj);
+		else
 			i915_gem_object_move_to_inactive(obj);
-		}
-	}
-
-	if (request->flush_domains != 0) {
-		struct drm_i915_gem_object *obj_priv, *next;
-
-		/* Clear the write domain and activity from any buffers
-		 * that are just waiting for a flush matching the one retired.
-		 */
-		list_for_each_entry_safe(obj_priv, next,
-					 &dev_priv->mm.flushing_list, list) {
-			struct drm_gem_object *obj = obj_priv->obj;
-
-			if (obj->write_domain & request->flush_domains) {
-				obj->write_domain = 0;
-				i915_gem_object_move_to_inactive(obj);
-			}
-		}
-
 	}
 }
 
@@ -892,25 +927,10 @@ i915_gem_object_wait_rendering(struct drm_gem_object *obj)
 	struct drm_i915_gem_object *obj_priv = obj->driver_private;
 	int ret;
 
-	/* If there are writes queued to the buffer, flush and
-	 * create a new seqno to wait for.
+	/* This function only exists to support waiting for existing rendering,
+	 * not for emitting required flushes.
 	 */
-	if (obj->write_domain & ~(I915_GEM_DOMAIN_CPU|I915_GEM_DOMAIN_GTT)) {
-		uint32_t write_domain = obj->write_domain;
-#if WATCH_BUF
-		DRM_INFO("%s: flushing object %p from write domain %08x\n",
-			  __func__, obj, write_domain);
-#endif
-		i915_gem_flush(dev, 0, write_domain);
-
-		i915_gem_object_move_to_active(obj);
-		obj_priv->last_rendering_seqno = i915_add_request(dev,
-								  write_domain);
-		BUG_ON(obj_priv->last_rendering_seqno == 0);
-#if WATCH_LRU
-		DRM_INFO("%s: flush moves to exec list %p\n", __func__, obj);
-#endif
-	}
+	BUG_ON((obj->write_domain & I915_GEM_GPU_DOMAINS) != 0);
 
 	/* If there is rendering queued on the buffer being evicted, wait for
 	 * it.
@@ -950,24 +970,16 @@ i915_gem_object_unbind(struct drm_gem_object *obj)
 		return -EINVAL;
 	}
 
-	/* Wait for any rendering to complete
-	 */
-	ret = i915_gem_object_wait_rendering(obj);
-	if (ret) {
-		DRM_ERROR("wait_rendering failed: %d\n", ret);
-		return ret;
-	}
-
 	/* Move the object to the CPU domain to ensure that
 	 * any possible CPU writes while it's not in the GTT
 	 * are flushed when we go to remap it. This will
 	 * also ensure that all pending GPU writes are finished
 	 * before we unbind.
 	 */
-	ret = i915_gem_object_set_domain(obj, I915_GEM_DOMAIN_CPU,
-					 I915_GEM_DOMAIN_CPU);
+	ret = i915_gem_object_set_to_cpu_domain(obj, 1);
 	if (ret) {
-		DRM_ERROR("set_domain failed: %d\n", ret);
+		if (ret != -ERESTARTSYS)
+			DRM_ERROR("set_domain failed: %d\n", ret);
 		return ret;
 	}
 
@@ -1083,6 +1095,21 @@ i915_gem_evict_something(struct drm_device *dev)
 }
 
 static int
+i915_gem_evict_everything(struct drm_device *dev)
+{
+	int ret;
+
+	for (;;) {
+		ret = i915_gem_evict_something(dev);
+		if (ret != 0)
+			break;
+	}
+	if (ret == -ENOMEM)
+		return 0;
+	return ret;
+}
+
+static int
 i915_gem_object_get_page_list(struct drm_gem_object *obj)
 {
 	struct drm_i915_gem_object *obj_priv = obj->driver_private;
@@ -1168,7 +1195,8 @@ i915_gem_object_bind_to_gtt(struct drm_gem_object *obj, unsigned alignment)
 
 		ret = i915_gem_evict_something(dev);
 		if (ret != 0) {
-			DRM_ERROR("Failed to evict a buffer %d\n", ret);
+			if (ret != -ERESTARTSYS)
+				DRM_ERROR("Failed to evict a buffer %d\n", ret);
 			return ret;
 		}
 		goto search_free;
@@ -1228,6 +1256,143 @@ i915_gem_clflush_object(struct drm_gem_object *obj)
 	drm_clflush_pages(obj_priv->page_list, obj->size / PAGE_SIZE);
 }
 
+/** Flushes any GPU write domain for the object if it's dirty. */
+static void
+i915_gem_object_flush_gpu_write_domain(struct drm_gem_object *obj)
+{
+	struct drm_device *dev = obj->dev;
+	uint32_t seqno;
+
+	if ((obj->write_domain & I915_GEM_GPU_DOMAINS) == 0)
+		return;
+
+	/* Queue the GPU write cache flushing we need. */
+	i915_gem_flush(dev, 0, obj->write_domain);
+	seqno = i915_add_request(dev, obj->write_domain);
+	obj->write_domain = 0;
+	i915_gem_object_move_to_active(obj, seqno);
+}
+
+/** Flushes the GTT write domain for the object if it's dirty. */
+static void
+i915_gem_object_flush_gtt_write_domain(struct drm_gem_object *obj)
+{
+	if (obj->write_domain != I915_GEM_DOMAIN_GTT)
+		return;
+
+	/* No actual flushing is required for the GTT write domain.   Writes
+	 * to it immediately go to main memory as far as we know, so there's
+	 * no chipset flush.  It also doesn't land in render cache.
+	 */
+	obj->write_domain = 0;
+}
+
+/** Flushes the CPU write domain for the object if it's dirty. */
+static void
+i915_gem_object_flush_cpu_write_domain(struct drm_gem_object *obj)
+{
+	struct drm_device *dev = obj->dev;
+
+	if (obj->write_domain != I915_GEM_DOMAIN_CPU)
+		return;
+
+	i915_gem_clflush_object(obj);
+	drm_agp_chipset_flush(dev);
+	obj->write_domain = 0;
+}
+
+/**
+ * Moves a single object to the GTT read, and possibly write domain.
+ *
+ * This function returns when the move is complete, including waiting on
+ * flushes to occur.
+ */
+static int
+i915_gem_object_set_to_gtt_domain(struct drm_gem_object *obj, int write)
+{
+	struct drm_i915_gem_object *obj_priv = obj->driver_private;
+	int ret;
+
+	/* Not valid to be called on unbound objects. */
+	if (obj_priv->gtt_space == NULL)
+		return -EINVAL;
+
+	i915_gem_object_flush_gpu_write_domain(obj);
+	/* Wait on any GPU rendering and flushing to occur. */
+	ret = i915_gem_object_wait_rendering(obj);
+	if (ret != 0)
+		return ret;
+
+	/* If we're writing through the GTT domain, then CPU and GPU caches
+	 * will need to be invalidated at next use.
+	 */
+	if (write)
+		obj->read_domains &= I915_GEM_DOMAIN_GTT;
+
+	i915_gem_object_flush_cpu_write_domain(obj);
+
+	/* It should now be out of any other write domains, and we can update
+	 * the domain values for our changes.
+	 */
+	BUG_ON((obj->write_domain & ~I915_GEM_DOMAIN_GTT) != 0);
+	obj->read_domains |= I915_GEM_DOMAIN_GTT;
+	if (write) {
+		obj->write_domain = I915_GEM_DOMAIN_GTT;
+		obj_priv->dirty = 1;
+	}
+
+	return 0;
+}
+
+/**
+ * Moves a single object to the CPU read, and possibly write domain.
+ *
+ * This function returns when the move is complete, including waiting on
+ * flushes to occur.
+ */
+static int
+i915_gem_object_set_to_cpu_domain(struct drm_gem_object *obj, int write)
+{
+	struct drm_device *dev = obj->dev;
+	int ret;
+
+	i915_gem_object_flush_gpu_write_domain(obj);
+	/* Wait on any GPU rendering and flushing to occur. */
+	ret = i915_gem_object_wait_rendering(obj);
+	if (ret != 0)
+		return ret;
+
+	i915_gem_object_flush_gtt_write_domain(obj);
+
+	/* If we have a partially-valid cache of the object in the CPU,
+	 * finish invalidating it and free the per-page flags.
+	 */
+	i915_gem_object_set_to_full_cpu_read_domain(obj);
+
+	/* Flush the CPU cache if it's still invalid. */
+	if ((obj->read_domains & I915_GEM_DOMAIN_CPU) == 0) {
+		i915_gem_clflush_object(obj);
+		drm_agp_chipset_flush(dev);
+
+		obj->read_domains |= I915_GEM_DOMAIN_CPU;
+	}
+
+	/* It should now be out of any other write domains, and we can update
+	 * the domain values for our changes.
+	 */
+	BUG_ON((obj->write_domain & ~I915_GEM_DOMAIN_CPU) != 0);
+
+	/* If we're writing through the CPU, then the GPU read domains will
+	 * need to be invalidated at next use.
+	 */
+	if (write) {
+		obj->read_domains &= I915_GEM_DOMAIN_CPU;
+		obj->write_domain = I915_GEM_DOMAIN_CPU;
+	}
+
+	return 0;
+}
+
 /*
  * Set the next domain for the specified object. This
  * may not actually perform the necessary flushing/invaliding though,
@@ -1339,16 +1504,18 @@ i915_gem_clflush_object(struct drm_gem_object *obj)
  *		MI_FLUSH
  *		drm_agp_chipset_flush
  */
-static int
-i915_gem_object_set_domain(struct drm_gem_object *obj,
-			    uint32_t read_domains,
-			    uint32_t write_domain)
+static void
+i915_gem_object_set_to_gpu_domain(struct drm_gem_object *obj,
+				  uint32_t read_domains,
+				  uint32_t write_domain)
 {
 	struct drm_device		*dev = obj->dev;
 	struct drm_i915_gem_object	*obj_priv = obj->driver_private;
 	uint32_t			invalidate_domains = 0;
 	uint32_t			flush_domains = 0;
-	int				ret;
+
+	BUG_ON(read_domains & I915_GEM_DOMAIN_CPU);
+	BUG_ON(write_domain == I915_GEM_DOMAIN_CPU);
 
 #if WATCH_BUF
 	DRM_INFO("%s: object %p read %08x -> %08x write %08x -> %08x\n",
@@ -1385,34 +1552,11 @@ i915_gem_object_set_domain(struct drm_gem_object *obj,
 		DRM_INFO("%s: CPU domain flush %08x invalidate %08x\n",
 			 __func__, flush_domains, invalidate_domains);
 #endif
-		/*
-		 * If we're invaliding the CPU cache and flushing a GPU cache,
-		 * then pause for rendering so that the GPU caches will be
-		 * flushed before the cpu cache is invalidated
-		 */
-		if ((invalidate_domains & I915_GEM_DOMAIN_CPU) &&
-		    (flush_domains & ~(I915_GEM_DOMAIN_CPU |
-				       I915_GEM_DOMAIN_GTT))) {
-			ret = i915_gem_object_wait_rendering(obj);
-			if (ret)
-				return ret;
-		}
 		i915_gem_clflush_object(obj);
 	}
 
 	if ((write_domain | flush_domains) != 0)
 		obj->write_domain = write_domain;
-
-	/* If we're invalidating the CPU domain, clear the per-page CPU
-	 * domain list as well.
-	 */
-	if (obj_priv->page_cpu_valid != NULL &&
-	    (write_domain != 0 ||
-	     read_domains & I915_GEM_DOMAIN_CPU)) {
-		drm_free(obj_priv->page_cpu_valid, obj->size / PAGE_SIZE,
-			 DRM_MEM_DRIVER);
-		obj_priv->page_cpu_valid = NULL;
-	}
 	obj->read_domains = read_domains;
 
 	dev->invalidate_domains |= invalidate_domains;
@@ -1423,47 +1567,94 @@ i915_gem_object_set_domain(struct drm_gem_object *obj,
 		 obj->read_domains, obj->write_domain,
 		 dev->invalidate_domains, dev->flush_domains);
 #endif
-	return 0;
 }
 
 /**
- * Set the read/write domain on a range of the object.
+ * Moves the object from a partially CPU read to a full one.
  *
- * Currently only implemented for CPU reads, otherwise drops to normal
- * i915_gem_object_set_domain().
+ * Note that this only resolves i915_gem_object_set_cpu_read_domain_range(),
+ * and doesn't handle transitioning from !(read_domains & I915_GEM_DOMAIN_CPU).
  */
-static int
-i915_gem_object_set_domain_range(struct drm_gem_object *obj,
-				 uint64_t offset,
-				 uint64_t size,
-				 uint32_t read_domains,
-				 uint32_t write_domain)
+static void
+i915_gem_object_set_to_full_cpu_read_domain(struct drm_gem_object *obj)
 {
+	struct drm_device *dev = obj->dev;
 	struct drm_i915_gem_object *obj_priv = obj->driver_private;
-	int ret, i;
 
-	if (obj->read_domains & I915_GEM_DOMAIN_CPU)
-		return 0;
+	if (!obj_priv->page_cpu_valid)
+		return;
 
-	if (read_domains != I915_GEM_DOMAIN_CPU ||
-	    write_domain != 0)
-		return i915_gem_object_set_domain(obj,
-						  read_domains, write_domain);
+	/* If we're partially in the CPU read domain, finish moving it in.
+	 */
+	if (obj->read_domains & I915_GEM_DOMAIN_CPU) {
+		int i;
 
-	/* Wait on any GPU rendering to the object to be flushed. */
+		for (i = 0; i <= (obj->size - 1) / PAGE_SIZE; i++) {
+			if (obj_priv->page_cpu_valid[i])
+				continue;
+			drm_clflush_pages(obj_priv->page_list + i, 1);
+		}
+		drm_agp_chipset_flush(dev);
+	}
+
+	/* Free the page_cpu_valid mappings which are now stale, whether
+	 * or not we've got I915_GEM_DOMAIN_CPU.
+	 */
+	drm_free(obj_priv->page_cpu_valid, obj->size / PAGE_SIZE,
+		 DRM_MEM_DRIVER);
+	obj_priv->page_cpu_valid = NULL;
+}
+
+/**
+ * Set the CPU read domain on a range of the object.
+ *
+ * The object ends up with I915_GEM_DOMAIN_CPU in its read flags although it's
+ * not entirely valid.  The page_cpu_valid member of the object flags which
+ * pages have been flushed, and will be respected by
+ * i915_gem_object_set_to_cpu_domain() if it's called on to get a valid mapping
+ * of the whole object.
+ *
+ * This function returns when the move is complete, including waiting on
+ * flushes to occur.
+ */
+static int
+i915_gem_object_set_cpu_read_domain_range(struct drm_gem_object *obj,
+					  uint64_t offset, uint64_t size)
+{
+	struct drm_i915_gem_object *obj_priv = obj->driver_private;
+	int i, ret;
+
+	if (offset == 0 && size == obj->size)
+		return i915_gem_object_set_to_cpu_domain(obj, 0);
+
+	i915_gem_object_flush_gpu_write_domain(obj);
+	/* Wait on any GPU rendering and flushing to occur. */
 	ret = i915_gem_object_wait_rendering(obj);
-	if (ret)
+	if (ret != 0)
 		return ret;
+	i915_gem_object_flush_gtt_write_domain(obj);
 
+	/* If we're already fully in the CPU read domain, we're done. */
+	if (obj_priv->page_cpu_valid == NULL &&
+	    (obj->read_domains & I915_GEM_DOMAIN_CPU) != 0)
+		return 0;
+
+	/* Otherwise, create/clear the per-page CPU read domain flag if we're
+	 * newly adding I915_GEM_DOMAIN_CPU
+	 */
 	if (obj_priv->page_cpu_valid == NULL) {
 		obj_priv->page_cpu_valid = drm_calloc(1, obj->size / PAGE_SIZE,
 						      DRM_MEM_DRIVER);
-	}
+		if (obj_priv->page_cpu_valid == NULL)
+			return -ENOMEM;
+	} else if ((obj->read_domains & I915_GEM_DOMAIN_CPU) == 0)
+		memset(obj_priv->page_cpu_valid, 0, obj->size / PAGE_SIZE);
 
 	/* Flush the cache on any pages that are still invalid from the CPU's
 	 * perspective.
 	 */
-	for (i = offset / PAGE_SIZE; i <= (offset + size - 1) / PAGE_SIZE; i++) {
+	for (i = offset / PAGE_SIZE; i <= (offset + size - 1) / PAGE_SIZE;
+	     i++) {
 		if (obj_priv->page_cpu_valid[i])
 			continue;
 
@@ -1472,39 +1663,14 @@ i915_gem_object_set_domain_range(struct drm_gem_object *obj,
 		obj_priv->page_cpu_valid[i] = 1;
 	}
 
-	return 0;
-}
-
-/**
- * Once all of the objects have been set in the proper domain,
- * perform the necessary flush and invalidate operations.
- *
- * Returns the write domains flushed, for use in flush tracking.
- */
-static uint32_t
-i915_gem_dev_set_domain(struct drm_device *dev)
-{
-	uint32_t flush_domains = dev->flush_domains;
-
-	/*
-	 * Now that all the buffers are synced to the proper domains,
-	 * flush and invalidate the collected domains
+	/* It should now be out of any other write domains, and we can update
+	 * the domain values for our changes.
 	 */
-	if (dev->invalidate_domains | dev->flush_domains) {
-#if WATCH_EXEC
-		DRM_INFO("%s: invalidate_domains %08x flush_domains %08x\n",
-			  __func__,
-			 dev->invalidate_domains,
-			 dev->flush_domains);
-#endif
-		i915_gem_flush(dev,
-			       dev->invalidate_domains,
-			       dev->flush_domains);
-		dev->invalidate_domains = 0;
-		dev->flush_domains = 0;
-	}
+	BUG_ON((obj->write_domain & ~I915_GEM_DOMAIN_CPU) != 0);
 
-	return flush_domains;
+	obj->read_domains |= I915_GEM_DOMAIN_CPU;
+
+	return 0;
 }
 
 /**
@@ -1585,6 +1751,18 @@ i915_gem_object_pin_and_relocate(struct drm_gem_object *obj,
 			return -EINVAL;
 		}
 
+		if (reloc.write_domain & I915_GEM_DOMAIN_CPU ||
+		    reloc.read_domains & I915_GEM_DOMAIN_CPU) {
+			DRM_ERROR("reloc with read/write CPU domains: "
+				  "obj %p target %d offset %d "
+				  "read %08x write %08x",
+				  obj, reloc.target_handle,
+				  (int) reloc.offset,
+				  reloc.read_domains,
+				  reloc.write_domain);
+			return -EINVAL;
+		}
+
 		if (reloc.write_domain && target_obj->pending_write_domain &&
 		    reloc.write_domain != target_obj->pending_write_domain) {
 			DRM_ERROR("Write domain conflict: "
@@ -1625,19 +1803,11 @@ i915_gem_object_pin_and_relocate(struct drm_gem_object *obj,
 			continue;
 		}
 
-		/* Now that we're going to actually write some data in,
-		 * make sure that any rendering using this buffer's contents
-		 * is completed.
-		 */
-		i915_gem_object_wait_rendering(obj);
-
-		/* As we're writing through the gtt, flush
-		 * any CPU writes before we write the relocations
-		 */
-		if (obj->write_domain & I915_GEM_DOMAIN_CPU) {
-			i915_gem_clflush_object(obj);
-			drm_agp_chipset_flush(dev);
-			obj->write_domain = 0;
+		ret = i915_gem_object_set_to_gtt_domain(obj, 1);
+		if (ret != 0) {
+			drm_gem_object_unreference(target_obj);
+			i915_gem_object_unpin(obj);
+			return -EINVAL;
 		}
 
 		/* Map the page containing the relocation we're going to
@@ -1779,6 +1949,7 @@ i915_gem_execbuffer(struct drm_device *dev, void *data,
 	int ret, i, pinned = 0;
 	uint64_t exec_offset;
 	uint32_t seqno, flush_domains;
+	int pin_tries;
 
 #if WATCH_EXEC
 	DRM_INFO("buffers_ptr %d buffer_count %d len %08x\n",
@@ -1827,14 +1998,7 @@ i915_gem_execbuffer(struct drm_device *dev, void *data,
 		return -EBUSY;
 	}
 
-	/* Zero the gloabl flush/invalidate flags. These
-	 * will be modified as each object is bound to the
-	 * gtt
-	 */
-	dev->invalidate_domains = 0;
-	dev->flush_domains = 0;
-
-	/* Look up object handles and perform the relocations */
+	/* Look up object handles */
 	for (i = 0; i < args->buffer_count; i++) {
 		object_list[i] = drm_gem_object_lookup(dev, file_priv,
 						       exec_list[i].handle);
@@ -1844,17 +2008,39 @@ i915_gem_execbuffer(struct drm_device *dev, void *data,
 			ret = -EBADF;
 			goto err;
 		}
+	}
 
-		object_list[i]->pending_read_domains = 0;
-		object_list[i]->pending_write_domain = 0;
-		ret = i915_gem_object_pin_and_relocate(object_list[i],
-						       file_priv,
-						       &exec_list[i]);
-		if (ret) {
-			DRM_ERROR("object bind and relocate failed %d\n", ret);
+	/* Pin and relocate */
+	for (pin_tries = 0; ; pin_tries++) {
+		ret = 0;
+		for (i = 0; i < args->buffer_count; i++) {
+			object_list[i]->pending_read_domains = 0;
+			object_list[i]->pending_write_domain = 0;
+			ret = i915_gem_object_pin_and_relocate(object_list[i],
+							       file_priv,
+							       &exec_list[i]);
+			if (ret)
+				break;
+			pinned = i + 1;
+		}
+		/* success */
+		if (ret == 0)
+			break;
+
+		/* error other than GTT full, or we've already tried again */
+		if (ret != -ENOMEM || pin_tries >= 1) {
+			DRM_ERROR("Failed to pin buffers %d\n", ret);
 			goto err;
 		}
-		pinned = i + 1;
+
+		/* unpin all of our buffers */
+		for (i = 0; i < pinned; i++)
+			i915_gem_object_unpin(object_list[i]);
+
+		/* evict everyone we can from the aperture */
+		ret = i915_gem_evict_everything(dev);
+		if (ret)
+			goto err;
 	}
 
 	/* Set the pending read domains for the batch buffer to COMMAND */
@@ -1864,21 +2050,37 @@ i915_gem_execbuffer(struct drm_device *dev, void *data,
 
 	i915_verify_inactive(dev, __FILE__, __LINE__);
 
+	/* Zero the global flush/invalidate flags. These
+	 * will be modified as new domains are computed
+	 * for each object
+	 */
+	dev->invalidate_domains = 0;
+	dev->flush_domains = 0;
+
 	for (i = 0; i < args->buffer_count; i++) {
 		struct drm_gem_object *obj = object_list[i];
 
-		/* make sure all previous memory operations have passed */
-		ret = i915_gem_object_set_domain(obj,
-						 obj->pending_read_domains,
-						 obj->pending_write_domain);
-		if (ret)
-			goto err;
+		/* Compute new gpu domains and update invalidate/flush */
+		i915_gem_object_set_to_gpu_domain(obj,
+						  obj->pending_read_domains,
+						  obj->pending_write_domain);
 	}
 
 	i915_verify_inactive(dev, __FILE__, __LINE__);
 
-	/* Flush/invalidate caches and chipset buffer */
-	flush_domains = i915_gem_dev_set_domain(dev);
+	if (dev->invalidate_domains | dev->flush_domains) {
+#if WATCH_EXEC
+		DRM_INFO("%s: invalidate_domains %08x flush_domains %08x\n",
+			  __func__,
+			 dev->invalidate_domains,
+			 dev->flush_domains);
+#endif
+		i915_gem_flush(dev,
+			       dev->invalidate_domains,
+			       dev->flush_domains);
+		if (dev->flush_domains)
+			(void)i915_add_request(dev, dev->flush_domains);
+	}
 
 	i915_verify_inactive(dev, __FILE__, __LINE__);
 
@@ -1898,8 +2100,6 @@ i915_gem_execbuffer(struct drm_device *dev, void *data,
 			      ~0);
 #endif
 
-	(void)i915_add_request(dev, flush_domains);
-
 	/* Exec the batchbuffer */
 	ret = i915_dispatch_gem_execbuffer(dev, args, exec_offset);
 	if (ret) {
@@ -1927,10 +2127,8 @@ i915_gem_execbuffer(struct drm_device *dev, void *data,
 	i915_file_priv->mm.last_gem_seqno = seqno;
 	for (i = 0; i < args->buffer_count; i++) {
 		struct drm_gem_object *obj = object_list[i];
-		struct drm_i915_gem_object *obj_priv = obj->driver_private;
 
-		i915_gem_object_move_to_active(obj);
-		obj_priv->last_rendering_seqno = seqno;
+		i915_gem_object_move_to_active(obj, seqno);
 #if WATCH_LRU
 		DRM_INFO("%s: move to exec list %p\n", __func__, obj);
 #endif
@@ -2061,11 +2259,7 @@ i915_gem_pin_ioctl(struct drm_device *dev, void *data,
 	/* XXX - flush the CPU caches for pinned objects
 	 * as the X server doesn't manage domains yet
 	 */
-	if (obj->write_domain & I915_GEM_DOMAIN_CPU) {
-		i915_gem_clflush_object(obj);
-		drm_agp_chipset_flush(dev);
-		obj->write_domain = 0;
-	}
+	i915_gem_object_flush_cpu_write_domain(obj);
 	args->offset = obj_priv->gtt_offset;
 	drm_gem_object_unreference(obj);
 	mutex_unlock(&dev->struct_mutex);
@@ -2167,29 +2361,6 @@ void i915_gem_free_object(struct drm_gem_object *obj)
 	drm_free(obj->driver_private, 1, DRM_MEM_DRIVER);
 }
 
-static int
-i915_gem_set_domain(struct drm_gem_object *obj,
-		    struct drm_file *file_priv,
-		    uint32_t read_domains,
-		    uint32_t write_domain)
-{
-	struct drm_device *dev = obj->dev;
-	int ret;
-	uint32_t flush_domains;
-
-	BUG_ON(!mutex_is_locked(&dev->struct_mutex));
-
-	ret = i915_gem_object_set_domain(obj, read_domains, write_domain);
-	if (ret)
-		return ret;
-	flush_domains = i915_gem_dev_set_domain(obj->dev);
-
-	if (flush_domains & ~(I915_GEM_DOMAIN_CPU|I915_GEM_DOMAIN_GTT))
-		(void) i915_add_request(dev, flush_domains);
-
-	return 0;
-}
-
 /** Unbinds all objects that are on the given buffer list. */
 static int
 i915_gem_evict_from_list(struct drm_device *dev, struct list_head *head)
diff --git a/drivers/gpu/drm/i915/i915_gem_proc.c b/drivers/gpu/drm/i915/i915_gem_proc.c
index 93de15b..e8d5abe 100644
--- a/drivers/gpu/drm/i915/i915_gem_proc.c
+++ b/drivers/gpu/drm/i915/i915_gem_proc.c
@@ -166,10 +166,9 @@ static int i915_gem_request_info(char *buf, char **start, off_t offset,
 	list_for_each_entry(gem_request, &dev_priv->mm.request_list,
 			    list)
 	{
-		DRM_PROC_PRINT("    %d @ %d %08x\n",
+		DRM_PROC_PRINT("    %d @ %d\n",
 			       gem_request->seqno,
-			       (int) (jiffies - gem_request->emitted_jiffies),
-			       gem_request->flush_domains);
+			       (int) (jiffies - gem_request->emitted_jiffies));
 	}
 	if (len > request + offset)
 		return request;
diff --git a/drivers/gpu/drm/i915/i915_gem_tiling.c b/drivers/gpu/drm/i915/i915_gem_tiling.c
index e8b85ac..a8cb694 100644
--- a/drivers/gpu/drm/i915/i915_gem_tiling.c
+++ b/drivers/gpu/drm/i915/i915_gem_tiling.c
@@ -119,9 +119,10 @@ i915_gem_detect_bit_6_swizzle(struct drm_device *dev)
 			    dcc & DCC_CHANNEL_XOR_DISABLE) {
 				swizzle_x = I915_BIT_6_SWIZZLE_9_10;
 				swizzle_y = I915_BIT_6_SWIZZLE_9;
-			} else if (IS_I965GM(dev) || IS_GM45(dev)) {
-				/* GM965 only does bit 11-based channel
-				 * randomization
+			} else if ((IS_I965GM(dev) || IS_GM45(dev)) &&
+				   (dcc & DCC_CHANNEL_XOR_BIT_17) == 0) {
+				/* GM965/GM45 does either bit 11 or bit 17
+				 * swizzling.
 				 */
 				swizzle_x = I915_BIT_6_SWIZZLE_9_10_11;
 				swizzle_y = I915_BIT_6_SWIZZLE_9_11;
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 0e476eb..9d24aae 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -522,6 +522,7 @@
 #define DCC_ADDRESSING_MODE_DUAL_CHANNEL_INTERLEAVED	(2 << 0)
 #define DCC_ADDRESSING_MODE_MASK			(3 << 0)
 #define DCC_CHANNEL_XOR_DISABLE				(1 << 10)
+#define DCC_CHANNEL_XOR_BIT_17				(1 << 9)
 
 /** 965 MCH register controlling DRAM channel configuration */
 #define C0DRB3			0x10206
diff --git a/drivers/gpu/drm/radeon/radeon_drv.h b/drivers/gpu/drm/radeon/radeon_drv.h
index 7a18378..3bbb871 100644
--- a/drivers/gpu/drm/radeon/radeon_drv.h
+++ b/drivers/gpu/drm/radeon/radeon_drv.h
@@ -299,7 +299,6 @@ typedef struct drm_radeon_private {
 	atomic_t swi_emitted;
 	int vblank_crtc;
 	uint32_t irq_enable_reg;
-	int irq_enabled;
 	uint32_t r500_disp_irq_reg;
 
 	struct radeon_surface surfaces[RADEON_MAX_SURFACES];
diff --git a/drivers/gpu/drm/radeon/radeon_irq.c b/drivers/gpu/drm/radeon/radeon_irq.c
index 97c0599..99be114 100644
--- a/drivers/gpu/drm/radeon/radeon_irq.c
+++ b/drivers/gpu/drm/radeon/radeon_irq.c
@@ -44,7 +44,8 @@ void radeon_irq_set_state(struct drm_device *dev, u32 mask, int state)
 	else
 		dev_priv->irq_enable_reg &= ~mask;
 
-	RADEON_WRITE(RADEON_GEN_INT_CNTL, dev_priv->irq_enable_reg);
+	if (!dev->irq_enabled)
+		RADEON_WRITE(RADEON_GEN_INT_CNTL, dev_priv->irq_enable_reg);
 }
 
 static void r500_vbl_irq_set_state(struct drm_device *dev, u32 mask, int state)
@@ -56,7 +57,8 @@ static void r500_vbl_irq_set_state(struct drm_device *dev, u32 mask, int state)
 	else
 		dev_priv->r500_disp_irq_reg &= ~mask;
 
-	RADEON_WRITE(R500_DxMODE_INT_MASK, dev_priv->r500_disp_irq_reg);
+	if (!dev->irq_enabled)
+		RADEON_WRITE(R500_DxMODE_INT_MASK, dev_priv->r500_disp_irq_reg);
 }
 
 int radeon_enable_vblank(struct drm_device *dev, int crtc)
@@ -355,8 +357,6 @@ void radeon_driver_irq_uninstall(struct drm_device * dev)
 	if (!dev_priv)
 		return;
 
-	dev_priv->irq_enabled = 0;
-
 	if ((dev_priv->flags & RADEON_FAMILY_MASK) >= CHIP_RS690)
 		RADEON_WRITE(R500_DxMODE_INT_MASK, 0);
 	/* Disable *all* interrupts */
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 5763040..1a00bb7 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -669,10 +669,12 @@ config BLK_DEV_CELLEB
 
 endif
 
+# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
 config BLK_DEV_IDE_PMAC
 	tristate "PowerMac on-board IDE support"
 	depends on PPC_PMAC && IDE=y
 	select IDE_TIMINGS
+	select BLK_DEV_IDEDMA_PCI
 	help
 	  This driver provides support for the on-board IDE controller on
 	  most of the recent Apple Power Macintoshes and PowerBooks.
@@ -689,16 +691,6 @@ config BLK_DEV_IDE_PMAC_ATA100FIRST
 	  CD-ROM on hda. This option changes this to more natural hda for
 	  hard disk and hdc for CD-ROM.
 
-config BLK_DEV_IDEDMA_PMAC
-	bool "PowerMac IDE DMA support"
-	depends on BLK_DEV_IDE_PMAC
-	select BLK_DEV_IDEDMA_PCI
-	help
-	  This option allows the driver for the on-board IDE controller on
-	  Power Macintoshes and PowerBooks to use DMA (direct memory access)
-	  to transfer data to and from memory.  Saying Y is safe and improves
-	  performance.
-
 config BLK_DEV_IDE_AU1XXX
        bool "IDE for AMD Alchemy Au1200"
        depends on SOC_AU1200
@@ -912,7 +904,7 @@ config BLK_DEV_UMC8672
 endif
 
 config BLK_DEV_IDEDMA
-	def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_PMAC || \
+	def_bool BLK_DEV_IDEDMA_SFF || \
 		 BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 
 endif # IDE
diff --git a/drivers/ide/alim15x3.c b/drivers/ide/alim15x3.c
index e56c7b7..45d2356 100644
--- a/drivers/ide/alim15x3.c
+++ b/drivers/ide/alim15x3.c
@@ -591,7 +591,7 @@ static int __init ali15x3_ide_init(void)
 
 static void __exit ali15x3_ide_exit(void)
 {
-	return pci_unregister_driver(&alim15x3_pci_driver);
+	pci_unregister_driver(&alim15x3_pci_driver);
 }
 
 module_init(ali15x3_ide_init);
diff --git a/drivers/ide/amd74xx.c b/drivers/ide/amd74xx.c
index 81ec731..c6bcd30 100644
--- a/drivers/ide/amd74xx.c
+++ b/drivers/ide/amd74xx.c
@@ -3,7 +3,7 @@
  * IDE driver for Linux.
  *
  * Copyright (c) 2000-2002 Vojtech Pavlik
- * Copyright (c) 2007 Bartlomiej Zolnierkiewicz
+ * Copyright (c) 2007-2008 Bartlomiej Zolnierkiewicz
  *
  * Based on the work of:
  *      Andre Hedrick
@@ -263,6 +263,15 @@ static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_
 			d.udma_mask = ATA_UDMA5;
 	}
 
+	/*
+	 * It seems that on some nVidia controllers using AltStatus
+	 * register can be unreliable so default to Status register
+	 * if the device is in Compatibility Mode.
+	 */
+	if (dev->vendor == PCI_VENDOR_ID_NVIDIA &&
+	    ide_pci_is_in_compatibility_mode(dev))
+		d.host_flags |= IDE_HFLAG_BROKEN_ALTSTATUS;
+
 	printk(KERN_INFO "%s %s: UDMA%s controller\n",
 		d.name, pci_name(dev), amd_dma[fls(d.udma_mask) - 1]);
 
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 7162d67..cc35d6d 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -132,10 +132,14 @@ int ide_end_request (ide_drive_t *drive, int uptodate, int nr_sectors)
 }
 EXPORT_SYMBOL(ide_end_request);
 
-static void ide_complete_power_step(ide_drive_t *drive, struct request *rq, u8 stat, u8 error)
+static void ide_complete_power_step(ide_drive_t *drive, struct request *rq)
 {
 	struct request_pm_state *pm = rq->data;
 
+#ifdef DEBUG_PM
+	printk(KERN_INFO "%s: complete_power_step(step: %d)\n",
+		drive->name, pm->pm_step);
+#endif
 	if (drive->media != ide_disk)
 		return;
 
@@ -172,7 +176,7 @@ static ide_startstop_t ide_start_power_step(ide_drive_t *drive, struct request *
 		/* Not supported? Switch to next step now. */
 		if (ata_id_flush_enabled(drive->id) == 0 ||
 		    (drive->dev_flags & IDE_DFLAG_WCACHE) == 0) {
-			ide_complete_power_step(drive, rq, 0, 0);
+			ide_complete_power_step(drive, rq);
 			return ide_stopped;
 		}
 		if (ata_id_flush_ext_enabled(drive->id))
@@ -191,7 +195,7 @@ static ide_startstop_t ide_start_power_step(ide_drive_t *drive, struct request *
 		if (drive->media != ide_disk)
 			pm->pm_step = IDE_PM_RESTORE_DMA;
 		else
-			ide_complete_power_step(drive, rq, 0, 0);
+			ide_complete_power_step(drive, rq);
 		return ide_stopped;
 	case IDE_PM_IDLE:		/* Resume step 2 (idle) */
 		args->tf.command = ATA_CMD_IDLEIMMEDIATE;
@@ -322,11 +326,8 @@ void ide_end_drive_cmd (ide_drive_t *drive, u8 stat, u8 err)
 		}
 	} else if (blk_pm_request(rq)) {
 		struct request_pm_state *pm = rq->data;
-#ifdef DEBUG_PM
-		printk("%s: complete_power_step(step: %d, stat: %x, err: %x)\n",
-			drive->name, rq->pm->pm_step, stat, err);
-#endif
-		ide_complete_power_step(drive, rq, stat, err);
+
+		ide_complete_power_step(drive, rq);
 		if (pm->pm_step == IDE_PM_COMPLETED)
 			ide_complete_pm_request(drive, rq);
 		return;
@@ -804,7 +805,7 @@ static ide_startstop_t start_request (ide_drive_t *drive, struct request *rq)
 			struct request_pm_state *pm = rq->data;
 #ifdef DEBUG_PM
 			printk("%s: start_power_step(step: %d)\n",
-				drive->name, rq->pm->pm_step);
+				drive->name, pm->pm_step);
 #endif
 			startstop = ide_start_power_step(drive, rq);
 			if (startstop == ide_stopped &&
@@ -967,14 +968,13 @@ static void ide_do_request (ide_hwgroup_t *hwgroup, int masked_irq)
 	ide_startstop_t	startstop;
 	int             loops = 0;
 
-	/* for atari only: POSSIBLY BROKEN HERE(?) */
-	ide_get_lock(ide_intr, hwgroup);
-
 	/* caller must own ide_lock */
 	BUG_ON(!irqs_disabled());
 
 	while (!hwgroup->busy) {
 		hwgroup->busy = 1;
+		/* for atari only */
+		ide_get_lock(ide_intr, hwgroup);
 		drive = choose_drive(hwgroup);
 		if (drive == NULL) {
 			int sleeping = 0;
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 5d6ba14..c41c3b9 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -457,18 +457,14 @@ int drive_is_ready (ide_drive_t *drive)
 	if (drive->waiting_for_dma)
 		return hwif->dma_ops->dma_test_irq(drive);
 
-#if 0
-	/* need to guarantee 400ns since last command was issued */
-	udelay(1);
-#endif
-
 	/*
 	 * We do a passive status test under shared PCI interrupts on
 	 * cards that truly share the ATA side interrupt, but may also share
 	 * an interrupt with another pci card/device.  We make no assumptions
 	 * about possible isa-pnp and pci-pnp issues yet.
 	 */
-	if (hwif->io_ports.ctl_addr)
+	if (hwif->io_ports.ctl_addr &&
+	    (hwif->host_flags & IDE_HFLAG_BROKEN_ALTSTATUS) == 0)
 		stat = hwif->tp_ops->read_altstatus(hwif);
 	else
 		/* Note: this may clear a pending IRQ!! */
@@ -610,6 +606,7 @@ static const struct drive_list_entry ivb_list[] = {
 	{ "TSSTcorp CDDVDW SH-S202N"	, "SB01"	},
 	{ "TSSTcorp CDDVDW SH-S202H"	, "SB00"	},
 	{ "TSSTcorp CDDVDW SH-S202H"	, "SB01"	},
+	{ "SAMSUNG SP0822N"		, "WA100-10"	},
 	{ NULL				, NULL		}
 };
 
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index 1649ea5..c55bdbd 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -266,7 +266,8 @@ static int actual_try_to_identify (ide_drive_t *drive, u8 cmd)
 	/* take a deep breath */
 	msleep(50);
 
-	if (io_ports->ctl_addr) {
+	if (io_ports->ctl_addr &&
+	    (hwif->host_flags & IDE_HFLAG_BROKEN_ALTSTATUS) == 0) {
 		a = tp_ops->read_altstatus(hwif);
 		s = tp_ops->read_status(hwif);
 		if ((a ^ s) & ~ATA_IDX)
diff --git a/drivers/ide/pmac.c b/drivers/ide/pmac.c
index 2e19d62..7c481bb 100644
--- a/drivers/ide/pmac.c
+++ b/drivers/ide/pmac.c
@@ -66,7 +66,6 @@ typedef struct pmac_ide_hwif {
 	struct macio_dev		*mdev;
 	u32				timings[4];
 	volatile u32 __iomem *		*kauai_fcr;
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
 	/* Those fields are duplicating what is in hwif. We currently
 	 * can't use the hwif ones because of some assumptions that are
 	 * beeing done by the generic code about the kind of dma controller
@@ -74,8 +73,6 @@ typedef struct pmac_ide_hwif {
 	 */
 	volatile struct dbdma_regs __iomem *	dma_regs;
 	struct dbdma_cmd*		dma_table_cpu;
-#endif
-	
 } pmac_ide_hwif_t;
 
 enum {
@@ -222,8 +219,6 @@ static const char* model_name[] = {
 #define KAUAI_FCR_UATA_RESET_N		0x00000002
 #define KAUAI_FCR_UATA_ENABLE		0x00000001
 
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
-
 /* Rounded Multiword DMA timings
  * 
  * I gave up finding a generic formula for all controller
@@ -413,8 +408,6 @@ static int pmac_ide_build_dmatable(ide_drive_t *drive, struct request *rq);
 static void pmac_ide_selectproc(ide_drive_t *drive);
 static void pmac_ide_kauai_selectproc(ide_drive_t *drive);
 
-#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
-
 #define PMAC_IDE_REG(x) \
 	((void __iomem *)((drive)->hwif->io_ports.data_addr + (x)))
 
@@ -584,8 +577,6 @@ pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
 	pmac_ide_do_update_timings(drive);
 }
 
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
-
 /*
  * Calculate KeyLargo ATA/66 UDMA timings
  */
@@ -786,7 +777,6 @@ set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
 		drive->name, speed & 0xf,  *timings);
 #endif	
 }
-#endif /* #ifdef CONFIG_BLK_DEV_IDEDMA_PMAC */
 
 static void pmac_ide_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
@@ -804,7 +794,6 @@ static void pmac_ide_set_dma_mode(ide_drive_t *drive, const u8 speed)
 	tl[0] = *timings;
 	tl[1] = *timings2;
 
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
 	if (speed >= XFER_UDMA_0) {
 		if (pmif->kind == controller_kl_ata4)
 			ret = set_timings_udma_ata4(&tl[0], speed);
@@ -817,7 +806,7 @@ static void pmac_ide_set_dma_mode(ide_drive_t *drive, const u8 speed)
 			ret = -1;
 	} else
 		set_timings_mdma(drive, pmif->kind, &tl[0], &tl[1], speed);
-#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
+
 	if (ret)
 		return;
 
@@ -1008,9 +997,7 @@ static const struct ide_port_info pmac_port_info = {
 	.chipset		= ide_pmac,
 	.tp_ops			= &pmac_tp_ops,
 	.port_ops		= &pmac_ide_port_ops,
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
 	.dma_ops		= &pmac_dma_ops,
-#endif
 	.host_flags		= IDE_HFLAG_SET_PIO_MODE_KEEP_DMA |
 				  IDE_HFLAG_POST_SET_MODE |
 				  IDE_HFLAG_MMIO |
@@ -1182,7 +1169,7 @@ pmac_ide_macio_attach(struct macio_dev *mdev, const struct of_device_id *match)
 	pmif->regbase = regbase;
 	pmif->irq = irq;
 	pmif->kauai_fcr = NULL;
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
+
 	if (macio_resource_count(mdev) >= 2) {
 		if (macio_request_resource(mdev, 1, "ide-pmac (dma)"))
 			printk(KERN_WARNING "ide-pmac: can't request DMA "
@@ -1192,7 +1179,7 @@ pmac_ide_macio_attach(struct macio_dev *mdev, const struct of_device_id *match)
 			pmif->dma_regs = ioremap(macio_resource_start(mdev, 1), 0x1000);
 	} else
 		pmif->dma_regs = NULL;
-#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
+
 	dev_set_drvdata(&mdev->ofdev.dev, pmif);
 
 	memset(&hw, 0, sizeof(hw));
@@ -1300,9 +1287,7 @@ pmac_ide_pci_attach(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	base = ioremap(rbase, rlen);
 	pmif->regbase = (unsigned long) base + 0x2000;
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
 	pmif->dma_regs = base + 0x1000;
-#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
 	pmif->kauai_fcr = base;
 	pmif->irq = pdev->irq;
 
@@ -1434,8 +1419,6 @@ out:
 	return error;
 }
 
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
-
 /*
  * pmac_ide_build_dmatable builds the DBDMA command list
  * for a transfer and sets the DBDMA channel to point to it.
@@ -1723,13 +1706,6 @@ static int __devinit pmac_ide_init_dma(ide_hwif_t *hwif,
 
 	return 0;
 }
-#else
-static int __devinit pmac_ide_init_dma(ide_hwif_t *hwif,
-				       const struct ide_port_info *d)
-{
-	return -EOPNOTSUPP;
-}
-#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
 
 module_init(pmac_ide_probe);
 
diff --git a/drivers/ide/sgiioc4.c b/drivers/ide/sgiioc4.c
index 7defa0a..a687a7d 100644
--- a/drivers/ide/sgiioc4.c
+++ b/drivers/ide/sgiioc4.c
@@ -550,7 +550,7 @@ static const struct ide_dma_ops sgiioc4_dma_ops = {
 	.dma_timeout		= ide_dma_timeout,
 };
 
-static const struct ide_port_info sgiioc4_port_info __devinitdata = {
+static const struct ide_port_info sgiioc4_port_info __devinitconst = {
 	.name			= DRV_NAME,
 	.chipset		= ide_pci,
 	.init_dma		= ide_dma_sgiioc4,
@@ -633,7 +633,7 @@ out:
 	return ret;
 }
 
-int
+int __devinit
 ioc4_ide_attach_one(struct ioc4_driver_data *idd)
 {
 	/* PCI-RT does not bring out IDE connection.
@@ -645,7 +645,7 @@ ioc4_ide_attach_one(struct ioc4_driver_data *idd)
 	return pci_init_sgiioc4(idd->idd_pdev);
 }
 
-static struct ioc4_submodule ioc4_ide_submodule = {
+static struct ioc4_submodule __devinitdata ioc4_ide_submodule = {
 	.is_name = "IOC4_ide",
 	.is_owner = THIS_MODULE,
 	.is_probe = ioc4_ide_attach_one,
diff --git a/drivers/ieee1394/nodemgr.c b/drivers/ieee1394/nodemgr.c
index 9e39f73..d333ae2 100644
--- a/drivers/ieee1394/nodemgr.c
+++ b/drivers/ieee1394/nodemgr.c
@@ -1685,6 +1685,7 @@ static int nodemgr_host_thread(void *data)
 		g = get_hpsb_generation(host);
 		for (i = 0; i < 4 ; i++) {
 			msleep_interruptible(63);
+			try_to_freeze();
 			if (kthread_should_stop())
 				goto exit;
 
@@ -1725,6 +1726,7 @@ static int nodemgr_host_thread(void *data)
 		/* Sleep 3 seconds */
 		for (i = 3000/200; i; i--) {
 			msleep_interruptible(200);
+			try_to_freeze();
 			if (kthread_should_stop())
 				goto exit;
 
diff --git a/drivers/input/keyboard/omap-keypad.c b/drivers/input/keyboard/omap-keypad.c
index 69e674e..db22fd9 100644
--- a/drivers/input/keyboard/omap-keypad.c
+++ b/drivers/input/keyboard/omap-keypad.c
@@ -101,7 +101,7 @@ static irqreturn_t omap_kp_interrupt(int irq, void *dev_id)
 	if (cpu_is_omap24xx()) {
 		int i;
 		for (i = 0; i < omap_kp->rows; i++)
-			disable_irq(OMAP_GPIO_IRQ(row_gpios[i]));
+			disable_irq(gpio_to_irq(row_gpios[i]));
 	} else
 		/* disable keyboard interrupt and schedule for handling */
 		omap_writew(1, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
@@ -224,7 +224,7 @@ static void omap_kp_tasklet(unsigned long data)
 		if (cpu_is_omap24xx()) {
 			int i;
 			for (i = 0; i < omap_kp_data->rows; i++)
-				enable_irq(OMAP_GPIO_IRQ(row_gpios[i]));
+				enable_irq(gpio_to_irq(row_gpios[i]));
 		} else {
 			omap_writew(0, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
 			kp_cur_group = -1;
@@ -397,7 +397,7 @@ static int __init omap_kp_probe(struct platform_device *pdev)
 		omap_writew(0, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
 	} else {
 		for (irq_idx = 0; irq_idx < omap_kp->rows; irq_idx++) {
-			if (request_irq(OMAP_GPIO_IRQ(row_gpios[irq_idx]),
+			if (request_irq(gpio_to_irq(row_gpios[irq_idx]),
 					omap_kp_interrupt,
 					IRQF_TRIGGER_FALLING,
 					"omap-keypad", omap_kp) < 0)
@@ -438,7 +438,7 @@ static int omap_kp_remove(struct platform_device *pdev)
 			gpio_free(col_gpios[i]);
 		for (i = 0; i < omap_kp->rows; i++) {
 			gpio_free(row_gpios[i]);
-			free_irq(OMAP_GPIO_IRQ(row_gpios[i]), 0);
+			free_irq(gpio_to_irq(row_gpios[i]), 0);
 		}
 	} else {
 		omap_writew(1, OMAP_MPUIO_BASE + OMAP_MPUIO_KBD_MASKIT);
diff --git a/drivers/isdn/hardware/avm/b1isa.c b/drivers/isdn/hardware/avm/b1isa.c
index 1e288ee..6461a32 100644
--- a/drivers/isdn/hardware/avm/b1isa.c
+++ b/drivers/isdn/hardware/avm/b1isa.c
@@ -233,10 +233,8 @@ static void __exit b1isa_exit(void)
 	int i;
 
 	for (i = 0; i < MAX_CARDS; i++) {
-		if (!io[i])
-			break;
-
-		b1isa_remove(&isa_dev[i]);
+		if (isa_dev[i].resource[0].start)
+			b1isa_remove(&isa_dev[i]);
 	}
 	unregister_capi_driver(&capi_driver_b1isa);
 }
diff --git a/drivers/isdn/hysdn/hysdn_net.c b/drivers/isdn/hysdn/hysdn_net.c
index cfa8fa5..3f2a0a2 100644
--- a/drivers/isdn/hysdn/hysdn_net.c
+++ b/drivers/isdn/hysdn/hysdn_net.c
@@ -83,12 +83,12 @@ net_open(struct net_device *dev)
 
 	/* Fill in the MAC-level header (if not already set) */
 	if (!card->mac_addr[0]) {
-		for (i = 0; i < ETH_ALEN - sizeof(unsigned long); i++)
+		for (i = 0; i < ETH_ALEN; i++)
 			dev->dev_addr[i] = 0xfc;
 		if ((in_dev = dev->ip_ptr) != NULL) {
 			struct in_ifaddr *ifa = in_dev->ifa_list;
 			if (ifa != NULL)
-				memcpy(dev->dev_addr + (ETH_ALEN - sizeof(unsigned long)), &ifa->ifa_local, sizeof(unsigned long));
+				memcpy(dev->dev_addr + (ETH_ALEN - sizeof(ifa->ifa_local)), &ifa->ifa_local, sizeof(ifa->ifa_local));
 		}
 	} else
 		memcpy(dev->dev_addr, card->mac_addr, ETH_ALEN);
diff --git a/drivers/md/dm-table.c b/drivers/md/dm-table.c
index a63161a..04e5fd7 100644
--- a/drivers/md/dm-table.c
+++ b/drivers/md/dm-table.c
@@ -668,7 +668,7 @@ static void check_for_valid_limits(struct io_restrictions *rs)
 	if (!rs->max_segment_size)
 		rs->max_segment_size = MAX_SEGMENT_SIZE;
 	if (!rs->seg_boundary_mask)
-		rs->seg_boundary_mask = -1;
+		rs->seg_boundary_mask = BLK_SEG_BOUNDARY_MASK;
 	if (!rs->bounce_pfn)
 		rs->bounce_pfn = -1;
 }
diff --git a/drivers/message/i2o/i2o_block.c b/drivers/message/i2o/i2o_block.c
index 84bdc2e..a443e13 100644
--- a/drivers/message/i2o/i2o_block.c
+++ b/drivers/message/i2o/i2o_block.c
@@ -354,7 +354,7 @@ static inline void i2o_block_sglist_free(struct i2o_block_request *ireq)
  *	@req: the request to prepare
  *
  *	Allocate the necessary i2o_block_request struct and connect it to
- *	the request. This is needed that we not loose the SG list later on.
+ *	the request. This is needed that we not lose the SG list later on.
  *
  *	Returns BLKPREP_OK on success or BLKPREP_DEFER on failure.
  */
diff --git a/drivers/message/i2o/iop.c b/drivers/message/i2o/iop.c
index be2b592..6e53a30 100644
--- a/drivers/message/i2o/iop.c
+++ b/drivers/message/i2o/iop.c
@@ -49,7 +49,6 @@ static int i2o_hrt_get(struct i2o_controller *c);
 /**
  *	i2o_msg_get_wait - obtain an I2O message from the IOP
  *	@c: I2O controller
- *	@msg: pointer to a I2O message pointer
  *	@wait: how long to wait until timeout
  *
  *	This function waits up to wait seconds for a message slot to be
diff --git a/drivers/misc/sgi-gru/grufault.c b/drivers/misc/sgi-gru/grufault.c
index 8c389d60..3ee698a 100644
--- a/drivers/misc/sgi-gru/grufault.c
+++ b/drivers/misc/sgi-gru/grufault.c
@@ -254,7 +254,11 @@ static int atomic_pte_lookup(struct vm_area_struct *vma, unsigned long vaddr,
 		return 1;
 
 	*paddr = pte_pfn(pte) << PAGE_SHIFT;
+#ifdef CONFIG_HUGETLB_PAGE
 	*pageshift = is_vm_hugetlb_page(vma) ? HPAGE_SHIFT : PAGE_SHIFT;
+#else
+	*pageshift = PAGE_SHIFT;
+#endif
 	return 0;
 
 err:
diff --git a/drivers/misc/sgi-gru/grufile.c b/drivers/misc/sgi-gru/grufile.c
index 5c027b6..6509838 100644
--- a/drivers/misc/sgi-gru/grufile.c
+++ b/drivers/misc/sgi-gru/grufile.c
@@ -481,7 +481,7 @@ struct vm_operations_struct gru_vm_ops = {
 	.fault		= gru_fault,
 };
 
-module_init(gru_init);
+fs_initcall(gru_init);
 module_exit(gru_exit);
 
 module_param(gru_options, ulong, 0644);
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index 76a7675..6659b22 100644
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -37,9 +37,9 @@
 #define	OPCODE_NORM_READ	0x03	/* Read data bytes (low frequency) */
 #define	OPCODE_FAST_READ	0x0b	/* Read data bytes (high frequency) */
 #define	OPCODE_PP		0x02	/* Page program (up to 256 bytes) */
-#define	OPCODE_BE_4K 		0x20	/* Erase 4KiB block */
+#define	OPCODE_BE_4K		0x20	/* Erase 4KiB block */
 #define	OPCODE_BE_32K		0x52	/* Erase 32KiB block */
-#define	OPCODE_BE		0xc7	/* Erase whole flash block */
+#define	OPCODE_CHIP_ERASE	0xc7	/* Erase whole flash chip */
 #define	OPCODE_SE		0xd8	/* Sector erase (usually 64KiB) */
 #define	OPCODE_RDID		0x9f	/* Read JEDEC ID */
 
@@ -167,7 +167,7 @@ static int wait_till_ready(struct m25p *flash)
  *
  * Returns 0 if successful, non-zero otherwise.
  */
-static int erase_block(struct m25p *flash)
+static int erase_chip(struct m25p *flash)
 {
 	DEBUG(MTD_DEBUG_LEVEL3, "%s: %s %dKiB\n",
 			flash->spi->dev.bus_id, __func__,
@@ -181,7 +181,7 @@ static int erase_block(struct m25p *flash)
 	write_enable(flash);
 
 	/* Set up command buffer. */
-	flash->command[0] = OPCODE_BE;
+	flash->command[0] = OPCODE_CHIP_ERASE;
 
 	spi_write(flash->spi, flash->command, 1);
 
@@ -250,15 +250,18 @@ static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr)
 
 	mutex_lock(&flash->lock);
 
-	/* REVISIT in some cases we could speed up erasing large regions
-	 * by using OPCODE_SE instead of OPCODE_BE_4K
-	 */
-
-	/* now erase those sectors */
-	if (len == flash->mtd.size && erase_block(flash)) {
+	/* whole-chip erase? */
+	if (len == flash->mtd.size && erase_chip(flash)) {
 		instr->state = MTD_ERASE_FAILED;
 		mutex_unlock(&flash->lock);
 		return -EIO;
+
+	/* REVISIT in some cases we could speed up erasing large regions
+	 * by using OPCODE_SE instead of OPCODE_BE_4K.  We may have set up
+	 * to use "small sector erase", but that's not always optimal.
+	 */
+
+	/* "sector"-at-a-time erase */
 	} else {
 		while (len) {
 			if (erase_sector(flash, addr)) {
@@ -574,10 +577,11 @@ static struct flash_info *__devinit jedec_probe(struct spi_device *spi)
 	for (tmp = 0, info = m25p_data;
 			tmp < ARRAY_SIZE(m25p_data);
 			tmp++, info++) {
-		if (info->jedec_id == jedec)
-			if (ext_jedec != 0 && info->ext_id != ext_jedec)
+		if (info->jedec_id == jedec) {
+			if (info->ext_id != 0 && info->ext_id != ext_jedec)
 				continue;
 			return info;
+		}
 	}
 	dev_err(&spi->dev, "unrecognized JEDEC id %06x\n", jedec);
 	return NULL;
diff --git a/drivers/mtd/maps/physmap.c b/drivers/mtd/maps/physmap.c
index 42d844f..dfbf3f2 100644
--- a/drivers/mtd/maps/physmap.c
+++ b/drivers/mtd/maps/physmap.c
@@ -19,7 +19,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/concat.h>
-#include <asm/io.h>
+#include <linux/io.h>
 
 #define MAX_RESOURCES		4
 
@@ -27,7 +27,6 @@ struct physmap_flash_info {
 	struct mtd_info		*mtd[MAX_RESOURCES];
 	struct mtd_info		*cmtd;
 	struct map_info		map[MAX_RESOURCES];
-	struct resource		*res;
 #ifdef CONFIG_MTD_PARTITIONS
 	int			nr_parts;
 	struct mtd_partition	*parts;
@@ -70,16 +69,7 @@ static int physmap_flash_remove(struct platform_device *dev)
 #endif
 			map_destroy(info->mtd[i]);
 		}
-
-		if (info->map[i].virt != NULL)
-			iounmap(info->map[i].virt);
-	}
-
-	if (info->res != NULL) {
-		release_resource(info->res);
-		kfree(info->res);
 	}
-
 	return 0;
 }
 
@@ -101,7 +91,8 @@ static int physmap_flash_probe(struct platform_device *dev)
 	if (physmap_data == NULL)
 		return -ENODEV;
 
-	info = kzalloc(sizeof(struct physmap_flash_info), GFP_KERNEL);
+	info = devm_kzalloc(&dev->dev, sizeof(struct physmap_flash_info),
+			    GFP_KERNEL);
 	if (info == NULL) {
 		err = -ENOMEM;
 		goto err_out;
@@ -114,10 +105,10 @@ static int physmap_flash_probe(struct platform_device *dev)
 		       (unsigned long long)(dev->resource[i].end - dev->resource[i].start + 1),
 		       (unsigned long long)dev->resource[i].start);
 
-		info->res = request_mem_region(dev->resource[i].start,
-					       dev->resource[i].end - dev->resource[i].start + 1,
-					       dev->dev.bus_id);
-		if (info->res == NULL) {
+		if (!devm_request_mem_region(&dev->dev,
+			dev->resource[i].start,
+			dev->resource[i].end - dev->resource[i].start + 1,
+			dev->dev.bus_id)) {
 			dev_err(&dev->dev, "Could not reserve memory region\n");
 			err = -ENOMEM;
 			goto err_out;
@@ -129,7 +120,8 @@ static int physmap_flash_probe(struct platform_device *dev)
 		info->map[i].bankwidth = physmap_data->width;
 		info->map[i].set_vpp = physmap_data->set_vpp;
 
-		info->map[i].virt = ioremap(info->map[i].phys, info->map[i].size);
+		info->map[i].virt = devm_ioremap(&dev->dev, info->map[i].phys,
+						 info->map[i].size);
 		if (info->map[i].virt == NULL) {
 			dev_err(&dev->dev, "Failed to ioremap flash region\n");
 			err = EIO;
diff --git a/drivers/mtd/nand/fsl_upm.c b/drivers/mtd/nand/fsl_upm.c
index 024e3ff..a83192f 100644
--- a/drivers/mtd/nand/fsl_upm.c
+++ b/drivers/mtd/nand/fsl_upm.c
@@ -163,9 +163,11 @@ static int __devinit fun_chip_init(struct fsl_upm_nand *fun,
 	ret = parse_mtd_partitions(&fun->mtd, part_types, &fun->parts, 0);
 
 #ifdef CONFIG_MTD_OF_PARTS
-	if (ret == 0)
-		ret = of_mtd_parse_partitions(fun->dev, &fun->mtd,
-					      flash_np, &fun->parts);
+	if (ret == 0) {
+		ret = of_mtd_parse_partitions(fun->dev, flash_np, &fun->parts);
+		if (ret < 0)
+			goto err;
+	}
 #endif
 	if (ret > 0)
 		ret = add_mtd_partitions(&fun->mtd, fun->parts, ret);
diff --git a/drivers/mtd/nand/pasemi_nand.c b/drivers/mtd/nand/pasemi_nand.c
index 75c8990..9bd6c9a 100644
--- a/drivers/mtd/nand/pasemi_nand.c
+++ b/drivers/mtd/nand/pasemi_nand.c
@@ -141,6 +141,7 @@ static int __devinit pasemi_nand_probe(struct of_device *ofdev,
 	}
 
 	lpcctl = pci_resource_start(pdev, 0);
+	pci_dev_put(pdev);
 
 	if (!request_region(lpcctl, 4, driver_name)) {
 		err = -EBUSY;
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index ce5752a..fc41444 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -269,6 +269,7 @@ static struct pxa3xx_nand_timing stm2GbX16_timing = {
 
 static struct pxa3xx_nand_flash stm2GbX16 = {
 	.timing = &stm2GbX16_timing,
+	.cmdset	= &largepage_cmdset,
 	.page_per_block = 64,
 	.page_size = 2048,
 	.flash_width = 16,
diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index e39b21d..d1e0b8e 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -32,19 +32,18 @@
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
 
-#include <asm/io.h>
 #include <asm/mach/flash.h>
-#include <asm/arch/gpmc.h>
-#include <asm/arch/onenand.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/pm.h>
+#include <mach/gpmc.h>
+#include <mach/onenand.h>
+#include <mach/gpio.h>
+#include <mach/pm.h>
 
-#include <linux/dma-mapping.h>
-#include <asm/dma-mapping.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
 
-#include <asm/arch/board.h>
+#include <mach/board.h>
 
 #define DRIVER_NAME "omap2-onenand"
 
@@ -150,7 +149,7 @@ static int omap2_onenand_wait(struct mtd_info *mtd, int state)
 
 		INIT_COMPLETION(c->irq_done);
 		if (c->gpio_irq) {
-			result = omap_get_gpio_datain(c->gpio_irq);
+			result = gpio_get_value(c->gpio_irq);
 			if (result == -1) {
 				ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
 				intr = read_reg(c, ONENAND_REG_INTERRUPT);
@@ -635,9 +634,9 @@ static int __devinit omap2_onenand_probe(struct platform_device *pdev)
 				"OneNAND\n", c->gpio_irq);
 			goto err_iounmap;
 	}
-	omap_set_gpio_direction(c->gpio_irq, 1);
+	gpio_direction_input(c->gpio_irq);
 
-	if ((r = request_irq(OMAP_GPIO_IRQ(c->gpio_irq),
+	if ((r = request_irq(gpio_to_irq(c->gpio_irq),
 			     omap2_onenand_interrupt, IRQF_TRIGGER_RISING,
 			     pdev->dev.driver->name, c)) < 0)
 		goto err_release_gpio;
@@ -724,7 +723,7 @@ err_release_dma:
 	if (c->dma_channel != -1)
 		omap_free_dma(c->dma_channel);
 	if (c->gpio_irq)
-		free_irq(OMAP_GPIO_IRQ(c->gpio_irq), c);
+		free_irq(gpio_to_irq(c->gpio_irq), c);
 err_release_gpio:
 	if (c->gpio_irq)
 		omap_free_gpio(c->gpio_irq);
@@ -761,7 +760,7 @@ static int __devexit omap2_onenand_remove(struct platform_device *pdev)
 	omap2_onenand_shutdown(pdev);
 	platform_set_drvdata(pdev, NULL);
 	if (c->gpio_irq) {
-		free_irq(OMAP_GPIO_IRQ(c->gpio_irq), c);
+		free_irq(gpio_to_irq(c->gpio_irq), c);
 		omap_free_gpio(c->gpio_irq);
 	}
 	iounmap(c->onenand.base);
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index f19acf8..017383a 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -114,7 +114,7 @@ obj-$(CONFIG_EL2) += 3c503.o 8390p.o
 obj-$(CONFIG_NE2000) += ne.o 8390p.o
 obj-$(CONFIG_NE2_MCA) += ne2.o 8390p.o
 obj-$(CONFIG_HPLAN) += hp.o 8390p.o
-obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390.o
+obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390p.o
 obj-$(CONFIG_ULTRA) += smc-ultra.o 8390.o
 obj-$(CONFIG_ULTRAMCA) += smc-mca.o 8390.o
 obj-$(CONFIG_ULTRA32) += smc-ultra32.o 8390.o
diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c
index d07e3f1..a1a3d0e 100644
--- a/drivers/net/bnx2.c
+++ b/drivers/net/bnx2.c
@@ -3144,6 +3144,28 @@ bnx2_has_work(struct bnx2_napi *bnapi)
 	return 0;
 }
 
+static void
+bnx2_chk_missed_msi(struct bnx2 *bp)
+{
+	struct bnx2_napi *bnapi = &bp->bnx2_napi[0];
+	u32 msi_ctrl;
+
+	if (bnx2_has_work(bnapi)) {
+		msi_ctrl = REG_RD(bp, BNX2_PCICFG_MSI_CONTROL);
+		if (!(msi_ctrl & BNX2_PCICFG_MSI_CONTROL_ENABLE))
+			return;
+
+		if (bnapi->last_status_idx == bp->idle_chk_status_idx) {
+			REG_WR(bp, BNX2_PCICFG_MSI_CONTROL, msi_ctrl &
+			       ~BNX2_PCICFG_MSI_CONTROL_ENABLE);
+			REG_WR(bp, BNX2_PCICFG_MSI_CONTROL, msi_ctrl);
+			bnx2_msi(bp->irq_tbl[0].vector, bnapi);
+		}
+	}
+
+	bp->idle_chk_status_idx = bnapi->last_status_idx;
+}
+
 static void bnx2_poll_link(struct bnx2 *bp, struct bnx2_napi *bnapi)
 {
 	struct status_block *sblk = bnapi->status_blk.msi;
@@ -3218,14 +3240,15 @@ static int bnx2_poll(struct napi_struct *napi, int budget)
 
 		work_done = bnx2_poll_work(bp, bnapi, work_done, budget);
 
-		if (unlikely(work_done >= budget))
-			break;
-
 		/* bnapi->last_status_idx is used below to tell the hw how
 		 * much work has been processed, so we must read it before
 		 * checking for more work.
 		 */
 		bnapi->last_status_idx = sblk->status_idx;
+
+		if (unlikely(work_done >= budget))
+			break;
+
 		rmb();
 		if (likely(!bnx2_has_work(bnapi))) {
 			netif_rx_complete(bp->dev, napi);
@@ -4570,6 +4593,8 @@ bnx2_init_chip(struct bnx2 *bp)
 	for (i = 0; i < BNX2_MAX_MSIX_VEC; i++)
 		bp->bnx2_napi[i].last_status_idx = 0;
 
+	bp->idle_chk_status_idx = 0xffff;
+
 	bp->rx_mode = BNX2_EMAC_RX_MODE_SORT_MODE;
 
 	/* Set up how to generate a link change interrupt. */
@@ -5718,6 +5743,10 @@ bnx2_timer(unsigned long data)
 	if (atomic_read(&bp->intr_sem) != 0)
 		goto bnx2_restart_timer;
 
+	if ((bp->flags & (BNX2_FLAG_USING_MSI | BNX2_FLAG_ONE_SHOT_MSI)) ==
+	     BNX2_FLAG_USING_MSI)
+		bnx2_chk_missed_msi(bp);
+
 	bnx2_send_heart_beat(bp);
 
 	bp->stats_blk->stat_FwRxDrop =
diff --git a/drivers/net/bnx2.h b/drivers/net/bnx2.h
index 617d953..0b032c3 100644
--- a/drivers/net/bnx2.h
+++ b/drivers/net/bnx2.h
@@ -378,6 +378,9 @@ struct l2_fhdr {
  *  pci_config_l definition
  *  offset: 0000
  */
+#define BNX2_PCICFG_MSI_CONTROL				0x00000058
+#define BNX2_PCICFG_MSI_CONTROL_ENABLE			 (1L<<16)
+
 #define BNX2_PCICFG_MISC_CONFIG				0x00000068
 #define BNX2_PCICFG_MISC_CONFIG_TARGET_BYTE_SWAP	 (1L<<2)
 #define BNX2_PCICFG_MISC_CONFIG_TARGET_MB_WORD_SWAP	 (1L<<3)
@@ -6863,6 +6866,9 @@ struct bnx2 {
 
 	u8			num_tx_rings;
 	u8			num_rx_rings;
+
+	u32			idle_chk_status_idx;
+
 };
 
 #define REG_RD(bp, offset)					\
diff --git a/drivers/net/chelsio/sge.c b/drivers/net/chelsio/sge.c
index d6c7d2a..7092df5 100644
--- a/drivers/net/chelsio/sge.c
+++ b/drivers/net/chelsio/sge.c
@@ -1035,10 +1035,6 @@ MODULE_PARM_DESC(copybreak, "Receive copy threshold");
  *	@pdev: the PCI device that received the packet
  *	@fl: the SGE free list holding the packet
  *	@len: the actual packet length, excluding any SGE padding
- *	@dma_pad: padding at beginning of buffer left by SGE DMA
- *	@skb_pad: padding to be used if the packet is copied
- *	@copy_thres: length threshold under which a packet should be copied
- *	@drop_thres: # of remaining buffers before we start dropping packets
  *
  *	Get the next packet from a free list and complete setup of the
  *	sk_buff.  If the packet is small we make a copy and recycle the
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 91795f7..122539a 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -345,7 +345,6 @@ no_buffers:
 /**
  * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
  * @adapter: address of board private structure
- * @rx_ring: pointer to receive ring structure
  * @cleaned_count: number of buffers to allocate this pass
  **/
 
diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60.c
index e1b441e..c414554 100644
--- a/drivers/net/enc28j60.c
+++ b/drivers/net/enc28j60.c
@@ -568,6 +568,17 @@ static u16 erxrdpt_workaround(u16 next_packet_ptr, u16 start, u16 end)
 	return erxrdpt;
 }
 
+/*
+ * Calculate wrap around when reading beyond the end of the RX buffer
+ */
+static u16 rx_packet_start(u16 ptr)
+{
+	if (ptr + RSV_SIZE > RXEND_INIT)
+		return (ptr + RSV_SIZE) - (RXEND_INIT - RXSTART_INIT + 1);
+	else
+		return ptr + RSV_SIZE;
+}
+
 static void nolock_rxfifo_init(struct enc28j60_net *priv, u16 start, u16 end)
 {
 	u16 erxrdpt;
@@ -938,8 +949,9 @@ static void enc28j60_hw_rx(struct net_device *ndev)
 			skb->dev = ndev;
 			skb_reserve(skb, NET_IP_ALIGN);
 			/* copy the packet from the receive buffer */
-			enc28j60_mem_read(priv, priv->next_pk_ptr + sizeof(rsv),
-					len, skb_put(skb, len));
+			enc28j60_mem_read(priv,
+				rx_packet_start(priv->next_pk_ptr),
+				len, skb_put(skb, len));
 			if (netif_msg_pktdata(priv))
 				dump_packet(__func__, skb->len, skb->data);
 			skb->protocol = eth_type_trans(skb, ndev);
diff --git a/drivers/net/hp-plus.c b/drivers/net/hp-plus.c
index fbbd3e6..c01e290 100644
--- a/drivers/net/hp-plus.c
+++ b/drivers/net/hp-plus.c
@@ -230,7 +230,7 @@ static int __init hpp_probe1(struct net_device *dev, int ioaddr)
 	dev->open = &hpp_open;
 	dev->stop = &hpp_close;
 #ifdef CONFIG_NET_POLL_CONTROLLER
-	dev->poll_controller = ei_poll;
+	dev->poll_controller = eip_poll;
 #endif
 
 	ei_status.name = name;
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index 1cbae85..20d27e6 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -1980,7 +1980,6 @@ static void igb_configure_rx(struct igb_adapter *adapter)
 
 /**
  * igb_free_tx_resources - Free Tx Resources per Queue
- * @adapter: board private structure
  * @tx_ring: Tx descriptor ring for a specific queue
  *
  * Free all transmit software resources
@@ -2033,7 +2032,6 @@ static void igb_unmap_and_free_tx_resource(struct igb_adapter *adapter,
 
 /**
  * igb_clean_tx_ring - Free Tx Buffers
- * @adapter: board private structure
  * @tx_ring: ring to be cleaned
  **/
 static void igb_clean_tx_ring(struct igb_ring *tx_ring)
@@ -2080,7 +2078,6 @@ static void igb_clean_all_tx_rings(struct igb_adapter *adapter)
 
 /**
  * igb_free_rx_resources - Free Rx Resources
- * @adapter: board private structure
  * @rx_ring: ring to clean the resources from
  *
  * Free all receive software resources
@@ -2120,7 +2117,6 @@ static void igb_free_all_rx_resources(struct igb_adapter *adapter)
 
 /**
  * igb_clean_rx_ring - Free Rx Buffers per Queue
- * @adapter: board private structure
  * @rx_ring: ring to free buffers from
  **/
 static void igb_clean_rx_ring(struct igb_ring *rx_ring)
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 8ed823a..5236f63 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -1320,7 +1320,6 @@ static inline void ixgbe_irq_enable(struct ixgbe_adapter *adapter)
  * ixgbe_intr - legacy mode Interrupt Handler
  * @irq: interrupt number
  * @data: pointer to a network interface device structure
- * @pt_regs: CPU registers structure
  **/
 static irqreturn_t ixgbe_intr(int irq, void *data)
 {
diff --git a/drivers/net/macvlan.c b/drivers/net/macvlan.c
index 4239450..590039c 100644
--- a/drivers/net/macvlan.c
+++ b/drivers/net/macvlan.c
@@ -70,6 +70,9 @@ static void macvlan_broadcast(struct sk_buff *skb,
 	struct sk_buff *nskb;
 	unsigned int i;
 
+	if (skb->protocol == htons(ETH_P_PAUSE))
+		return;
+
 	for (i = 0; i < MACVLAN_HASH_SIZE; i++) {
 		hlist_for_each_entry_rcu(vlan, n, &port->vlan_hash[i], hlist) {
 			dev = vlan->dev;
diff --git a/drivers/net/netx-eth.c b/drivers/net/netx-eth.c
index b9bed82..b289a0a 100644
--- a/drivers/net/netx-eth.c
+++ b/drivers/net/netx-eth.c
@@ -401,6 +401,8 @@ static int netx_eth_drv_probe(struct platform_device *pdev)
 	priv->xmac_base = priv->xc->xmac_base;
 	priv->sram_base = priv->xc->sram_base;
 
+	spin_lock_init(&priv->lock);
+
 	ret = pfifo_request(PFIFO_MASK(priv->id));
 	if (ret) {
 		printk("unable to request PFIFO\n");
diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c
index b37a498..0418045 100644
--- a/drivers/net/pcmcia/axnet_cs.c
+++ b/drivers/net/pcmcia/axnet_cs.c
@@ -779,6 +779,7 @@ static struct pcmcia_device_id axnet_ids[] = {
 	PCMCIA_DEVICE_PROD_ID12("IO DATA", "ETXPCM", 0x547e66dc, 0x233adac2),
 	PCMCIA_DEVICE_PROD_ID12("Linksys", "EtherFast 10/100 PC Card (PCMPC100 V3)", 0x0733cc81, 0x232019a8),
 	PCMCIA_DEVICE_PROD_ID12("MELCO", "LPC3-TX", 0x481e0094, 0xf91af609),
+	PCMCIA_DEVICE_PROD_ID12("NETGEAR", "FA411", 0x9aa79dc3, 0x40fad875),
 	PCMCIA_DEVICE_PROD_ID12("PCMCIA", "100BASE", 0x281f1c5d, 0x7c2add04),
 	PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FastEtherCard", 0x281f1c5d, 0x7ef26116),
 	PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FEP501", 0x281f1c5d, 0x2e272058),
@@ -1174,7 +1175,6 @@ static int ei_start_xmit(struct sk_buff *skb, struct net_device *dev)
  * ax_interrupt - handle the interrupts from an 8390
  * @irq: interrupt number
  * @dev_id: a pointer to the net_device
- * @regs: unused
  *
  * Handle the ether interface interrupts. We pull packets from
  * the 8390 via the card specific functions and fire them at the networking
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index e40d630..ce486f0 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -1693,7 +1693,6 @@ static struct pcmcia_device_id pcnet_ids[] = {
 	PCMCIA_DEVICE_PROD_ID12("National Semiconductor", "InfoMover NE4100", 0x36e1191f, 0xa6617ec8),
 	PCMCIA_DEVICE_PROD_ID12("NEC", "PC-9801N-J12", 0x18df0ba0, 0xbc912d76),
 	PCMCIA_DEVICE_PROD_ID12("NETGEAR", "FA410TX", 0x9aa79dc3, 0x60e5bc0e),
-	PCMCIA_DEVICE_PROD_ID12("NETGEAR", "FA411", 0x9aa79dc3, 0x40fad875),
 	PCMCIA_DEVICE_PROD_ID12("Network Everywhere", "Fast Ethernet 10/100 PC Card", 0x820a67b6, 0x31ed1a5f),
 	PCMCIA_DEVICE_PROD_ID12("NextCom K.K.", "Next Hawk", 0xaedaec74, 0xad050ef1),
 	PCMCIA_DEVICE_PROD_ID12("PCMCIA", "10/100Mbps Ethernet Card", 0x281f1c5d, 0x6e41773b),
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 55bc24b2..25acbbd 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -227,8 +227,17 @@ struct phy_device * get_phy_device(struct mii_bus *bus, int addr)
 	if (r)
 		return ERR_PTR(r);
 
-	/* If the phy_id is all Fs or all 0s, there is no device there */
-	if ((0xffff == phy_id) || (0x00 == phy_id))
+	/* If the phy_id is mostly Fs, there is no device there */
+	if ((phy_id & 0x1fffffff) == 0x1fffffff)
+		return NULL;
+
+	/*
+	 * Broken hardware is sometimes missing the pull down resistor on the
+	 * MDIO line, which results in reads to non-existent devices returning
+	 * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
+	 * device as well.
+	 */
+	if (phy_id == 0)
 		return NULL;
 
 	dev = phy_device_create(bus, addr, phy_id);
diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c
index 8874497..dd3b244 100644
--- a/drivers/net/phy/vitesse.c
+++ b/drivers/net/phy/vitesse.c
@@ -34,6 +34,8 @@
 #define MII_VSC8244_IMASK_DUPLEX	0x1000
 #define MII_VSC8244_IMASK_MASK		0xf000
 
+#define MII_VSC8221_IMASK_MASK		0xa000
+
 /* Vitesse Interrupt Status Register */
 #define MII_VSC8244_ISTAT		0x1a
 #define MII_VSC8244_ISTAT_STATUS	0x8000
@@ -49,6 +51,12 @@
 #define MII_VSC8244_AUXCONSTAT_GBIT    	0x0010
 #define MII_VSC8244_AUXCONSTAT_100     	0x0008
 
+#define MII_VSC8221_AUXCONSTAT_INIT	0x0004 /* need to set this bit? */
+#define MII_VSC8221_AUXCONSTAT_RESERVED	0x0004
+
+#define PHY_ID_VSC8244			0x000fc6c0
+#define PHY_ID_VSC8221			0x000fc550
+
 MODULE_DESCRIPTION("Vitesse PHY driver");
 MODULE_AUTHOR("Kriston Carson");
 MODULE_LICENSE("GPL");
@@ -95,13 +103,15 @@ static int vsc824x_ack_interrupt(struct phy_device *phydev)
 	return (err < 0) ? err : 0;
 }
 
-static int vsc824x_config_intr(struct phy_device *phydev)
+static int vsc82xx_config_intr(struct phy_device *phydev)
 {
 	int err;
 
 	if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
 		err = phy_write(phydev, MII_VSC8244_IMASK,
-				MII_VSC8244_IMASK_MASK);
+			phydev->drv->phy_id == PHY_ID_VSC8244 ?
+				MII_VSC8244_IMASK_MASK :
+				MII_VSC8221_IMASK_MASK);
 	else {
 		/*
 		 * The Vitesse PHY cannot clear the interrupt
@@ -120,7 +130,7 @@ static int vsc824x_config_intr(struct phy_device *phydev)
 
 /* Vitesse 824x */
 static struct phy_driver vsc8244_driver = {
-	.phy_id		= 0x000fc6c0,
+	.phy_id		= PHY_ID_VSC8244,
 	.name		= "Vitesse VSC8244",
 	.phy_id_mask	= 0x000fffc0,
 	.features	= PHY_GBIT_FEATURES,
@@ -129,19 +139,55 @@ static struct phy_driver vsc8244_driver = {
 	.config_aneg	= &genphy_config_aneg,
 	.read_status	= &genphy_read_status,
 	.ack_interrupt	= &vsc824x_ack_interrupt,
-	.config_intr	= &vsc824x_config_intr,
+	.config_intr	= &vsc82xx_config_intr,
 	.driver 	= { .owner = THIS_MODULE,},
 };
 
-static int __init vsc8244_init(void)
+static int vsc8221_config_init(struct phy_device *phydev)
 {
-	return phy_driver_register(&vsc8244_driver);
+	int err;
+
+	err = phy_write(phydev, MII_VSC8244_AUX_CONSTAT,
+			MII_VSC8221_AUXCONSTAT_INIT);
+	return err;
+
+	/* Perhaps we should set EXT_CON1 based on the interface?
+	   Options are 802.3Z SerDes or SGMII */
+}
+
+/* Vitesse 8221 */
+static struct phy_driver vsc8221_driver = {
+	.phy_id		= PHY_ID_VSC8221,
+	.phy_id_mask	= 0x000ffff0,
+	.name		= "Vitesse VSC8221",
+	.features	= PHY_GBIT_FEATURES,
+	.flags		= PHY_HAS_INTERRUPT,
+	.config_init	= &vsc8221_config_init,
+	.config_aneg	= &genphy_config_aneg,
+	.read_status	= &genphy_read_status,
+	.ack_interrupt	= &vsc824x_ack_interrupt,
+	.config_intr	= &vsc82xx_config_intr,
+	.driver 	= { .owner = THIS_MODULE,},
+};
+
+static int __init vsc82xx_init(void)
+{
+	int err;
+
+	err = phy_driver_register(&vsc8244_driver);
+	if (err < 0)
+		return err;
+	err = phy_driver_register(&vsc8221_driver);
+	if (err < 0)
+		phy_driver_unregister(&vsc8244_driver);
+	return err;
 }
 
-static void __exit vsc8244_exit(void)
+static void __exit vsc82xx_exit(void)
 {
 	phy_driver_unregister(&vsc8244_driver);
+	phy_driver_unregister(&vsc8221_driver);
 }
 
-module_init(vsc8244_init);
-module_exit(vsc8244_exit);
+module_init(vsc82xx_init);
+module_exit(vsc82xx_exit);
diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c
index 185b1df..e98d977 100644
--- a/drivers/net/pppol2tp.c
+++ b/drivers/net/pppol2tp.c
@@ -1353,6 +1353,7 @@ static int pppol2tp_release(struct socket *sock)
 			kfree_skb(skb);
 			sock_put(sk);
 		}
+		sock_put(sk);
 	}
 
 	release_sock(sk);
diff --git a/drivers/net/sis900.c b/drivers/net/sis900.c
index fa3a460..8e8337e 100644
--- a/drivers/net/sis900.c
+++ b/drivers/net/sis900.c
@@ -1630,7 +1630,6 @@ sis900_start_xmit(struct sk_buff *skb, struct net_device *net_dev)
  *	sis900_interrupt - sis900 interrupt handler
  *	@irq: the irq number
  *	@dev_instance: the client data object
- *	@regs: snapshot of processor context
  *
  *	The interrupt handler does all of the Rx thread work,
  *	and cleans up after the Tx thread
diff --git a/drivers/net/spider_net.c b/drivers/net/spider_net.c
index b6435d0..07599b4 100644
--- a/drivers/net/spider_net.c
+++ b/drivers/net/spider_net.c
@@ -672,7 +672,6 @@ write_hash:
 /**
  * spider_net_prepare_tx_descr - fill tx descriptor with skb data
  * @card: card structure
- * @descr: descriptor structure to fill out
  * @skb: packet to use
  *
  * returns 0 on success, <0 on failure.
@@ -867,7 +866,6 @@ spider_net_release_tx_chain(struct spider_net_card *card, int brutal)
 /**
  * spider_net_kick_tx_dma - enables TX DMA processing
  * @card: card structure
- * @descr: descriptor address to enable TX processing at
  *
  * This routine will start the transmit DMA running if
  * it is not already running. This routine ned only be
@@ -1637,7 +1635,6 @@ spider_net_handle_error_irq(struct spider_net_card *card, u32 status_reg,
  * spider_net_interrupt - interrupt handler for spider_net
  * @irq: interrupt number
  * @ptr: pointer to net_device
- * @regs: PU registers
  *
  * returns IRQ_HANDLED, if interrupt was for driver, or IRQ_NONE, if no
  * interrupt found raised by card.
@@ -2419,7 +2416,6 @@ spider_net_undo_pci_setup(struct spider_net_card *card)
 
 /**
  * spider_net_setup_pci_dev - sets up the device in terms of PCI operations
- * @card: card structure
  * @pdev: PCI device
  *
  * Returns the card structure or NULL if any errors occur
diff --git a/drivers/net/sungem.c b/drivers/net/sungem.c
index 4291458..1349e41 100644
--- a/drivers/net/sungem.c
+++ b/drivers/net/sungem.c
@@ -1714,7 +1714,7 @@ static void gem_init_phy(struct gem *gp)
 		/* Reset PCS unit. */
 		val = readl(gp->regs + PCS_MIICTRL);
 		val |= PCS_MIICTRL_RST;
-		writeb(val, gp->regs + PCS_MIICTRL);
+		writel(val, gp->regs + PCS_MIICTRL);
 
 		limit = 32;
 		while (readl(gp->regs + PCS_MIICTRL) & PCS_MIICTRL_RST) {
diff --git a/drivers/net/wireless/ath5k/base.c b/drivers/net/wireless/ath5k/base.c
index cfd4d05..2d14255 100644
--- a/drivers/net/wireless/ath5k/base.c
+++ b/drivers/net/wireless/ath5k/base.c
@@ -240,6 +240,10 @@ static u64 ath5k_get_tsf(struct ieee80211_hw *hw);
 static void ath5k_reset_tsf(struct ieee80211_hw *hw);
 static int ath5k_beacon_update(struct ieee80211_hw *hw,
 		struct sk_buff *skb);
+static void ath5k_bss_info_changed(struct ieee80211_hw *hw,
+		struct ieee80211_vif *vif,
+		struct ieee80211_bss_conf *bss_conf,
+		u32 changes);
 
 static struct ieee80211_ops ath5k_hw_ops = {
 	.tx 		= ath5k_tx,
@@ -256,6 +260,7 @@ static struct ieee80211_ops ath5k_hw_ops = {
 	.get_tx_stats 	= ath5k_get_tx_stats,
 	.get_tsf 	= ath5k_get_tsf,
 	.reset_tsf 	= ath5k_reset_tsf,
+	.bss_info_changed = ath5k_bss_info_changed,
 };
 
 /*
@@ -2942,7 +2947,7 @@ static void ath5k_configure_filter(struct ieee80211_hw *hw,
 		sc->opmode != NL80211_IFTYPE_MESH_POINT &&
 		test_bit(ATH_STAT_PROMISC, sc->status))
 		rfilt |= AR5K_RX_FILTER_PROM;
-	if (sc->opmode == NL80211_IFTYPE_STATION ||
+	if ((sc->opmode == NL80211_IFTYPE_STATION && sc->assoc) ||
 		sc->opmode == NL80211_IFTYPE_ADHOC) {
 		rfilt |= AR5K_RX_FILTER_BEACON;
 	}
@@ -3083,4 +3088,32 @@ ath5k_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb)
 end:
 	return ret;
 }
+static void
+set_beacon_filter(struct ieee80211_hw *hw, bool enable)
+{
+	struct ath5k_softc *sc = hw->priv;
+	struct ath5k_hw *ah = sc->ah;
+	u32 rfilt;
+	rfilt = ath5k_hw_get_rx_filter(ah);
+	if (enable)
+		rfilt |= AR5K_RX_FILTER_BEACON;
+	else
+		rfilt &= ~AR5K_RX_FILTER_BEACON;
+	ath5k_hw_set_rx_filter(ah, rfilt);
+	sc->filter_flags = rfilt;
+}
 
+static void ath5k_bss_info_changed(struct ieee80211_hw *hw,
+				    struct ieee80211_vif *vif,
+				    struct ieee80211_bss_conf *bss_conf,
+				    u32 changes)
+{
+	struct ath5k_softc *sc = hw->priv;
+	if (changes & BSS_CHANGED_ASSOC) {
+		mutex_lock(&sc->lock);
+		sc->assoc = bss_conf->assoc;
+		if (sc->opmode == NL80211_IFTYPE_STATION)
+			set_beacon_filter(hw, sc->assoc);
+		mutex_unlock(&sc->lock);
+	}
+}
diff --git a/drivers/net/wireless/ath5k/base.h b/drivers/net/wireless/ath5k/base.h
index 06d1054..facc60d 100644
--- a/drivers/net/wireless/ath5k/base.h
+++ b/drivers/net/wireless/ath5k/base.h
@@ -179,6 +179,7 @@ struct ath5k_softc {
 
 	struct timer_list	calib_tim;	/* calibration timer */
 	int 			power_level;	/* Requested tx power in dbm */
+	bool			assoc;		/* assocate state */
 };
 
 #define ath5k_hw_hasbssidmask(_ah) \
diff --git a/drivers/net/wireless/ath5k/debug.c b/drivers/net/wireless/ath5k/debug.c
index 19980cb..ccaeb5c 100644
--- a/drivers/net/wireless/ath5k/debug.c
+++ b/drivers/net/wireless/ath5k/debug.c
@@ -417,19 +417,19 @@ ath5k_debug_init_device(struct ath5k_softc *sc)
 	sc->debug.debugfs_phydir = debugfs_create_dir(wiphy_name(sc->hw->wiphy),
 				ath5k_global_debugfs);
 
-	sc->debug.debugfs_debug = debugfs_create_file("debug", 0666,
+	sc->debug.debugfs_debug = debugfs_create_file("debug", S_IWUSR | S_IRUGO,
 				sc->debug.debugfs_phydir, sc, &fops_debug);
 
-	sc->debug.debugfs_registers = debugfs_create_file("registers", 0444,
+	sc->debug.debugfs_registers = debugfs_create_file("registers", S_IRUGO,
 				sc->debug.debugfs_phydir, sc, &fops_registers);
 
-	sc->debug.debugfs_tsf = debugfs_create_file("tsf", 0666,
+	sc->debug.debugfs_tsf = debugfs_create_file("tsf", S_IWUSR | S_IRUGO,
 				sc->debug.debugfs_phydir, sc, &fops_tsf);
 
-	sc->debug.debugfs_beacon = debugfs_create_file("beacon", 0666,
+	sc->debug.debugfs_beacon = debugfs_create_file("beacon", S_IWUSR | S_IRUGO,
 				sc->debug.debugfs_phydir, sc, &fops_beacon);
 
-	sc->debug.debugfs_reset = debugfs_create_file("reset", 0222,
+	sc->debug.debugfs_reset = debugfs_create_file("reset", S_IWUSR,
 				sc->debug.debugfs_phydir, sc, &fops_reset);
 }
 
diff --git a/drivers/net/wireless/ath9k/beacon.c b/drivers/net/wireless/ath9k/beacon.c
index 9e15c30..4dd1c1b 100644
--- a/drivers/net/wireless/ath9k/beacon.c
+++ b/drivers/net/wireless/ath9k/beacon.c
@@ -170,7 +170,7 @@ static struct ath_buf *ath_beacon_generate(struct ath_softc *sc, int if_id)
 	skb = (struct sk_buff *)bf->bf_mpdu;
 	if (skb) {
 		pci_unmap_single(sc->pdev, bf->bf_dmacontext,
-				 skb_end_pointer(skb) - skb->head,
+				 skb->len,
 				 PCI_DMA_TODEVICE);
 	}
 
@@ -193,7 +193,7 @@ static struct ath_buf *ath_beacon_generate(struct ath_softc *sc, int if_id)
 
 	bf->bf_buf_addr = bf->bf_dmacontext =
 		pci_map_single(sc->pdev, skb->data,
-			       skb_end_pointer(skb) - skb->head,
+			       skb->len,
 			       PCI_DMA_TODEVICE);
 
 	skb = ieee80211_get_buffered_bc(sc->hw, avp->av_if_data);
@@ -352,7 +352,7 @@ int ath_beacon_alloc(struct ath_softc *sc, int if_id)
 	if (bf->bf_mpdu != NULL) {
 		skb = (struct sk_buff *)bf->bf_mpdu;
 		pci_unmap_single(sc->pdev, bf->bf_dmacontext,
-				 skb_end_pointer(skb) - skb->head,
+				 skb->len,
 				 PCI_DMA_TODEVICE);
 		dev_kfree_skb_any(skb);
 		bf->bf_mpdu = NULL;
@@ -412,7 +412,7 @@ int ath_beacon_alloc(struct ath_softc *sc, int if_id)
 
 	bf->bf_buf_addr = bf->bf_dmacontext =
 		pci_map_single(sc->pdev, skb->data,
-			       skb_end_pointer(skb) - skb->head,
+			       skb->len,
 			       PCI_DMA_TODEVICE);
 	bf->bf_mpdu = skb;
 
@@ -439,7 +439,7 @@ void ath_beacon_return(struct ath_softc *sc, struct ath_vap *avp)
 		if (bf->bf_mpdu != NULL) {
 			struct sk_buff *skb = (struct sk_buff *)bf->bf_mpdu;
 			pci_unmap_single(sc->pdev, bf->bf_dmacontext,
-					 skb_end_pointer(skb) - skb->head,
+					 skb->len,
 					 PCI_DMA_TODEVICE);
 			dev_kfree_skb_any(skb);
 			bf->bf_mpdu = NULL;
diff --git a/drivers/net/wireless/ath9k/recv.c b/drivers/net/wireless/ath9k/recv.c
index 4983402..504a044 100644
--- a/drivers/net/wireless/ath9k/recv.c
+++ b/drivers/net/wireless/ath9k/recv.c
@@ -49,10 +49,12 @@ static void ath_rx_buf_link(struct ath_softc *sc, struct ath_buf *bf)
 	ASSERT(skb != NULL);
 	ds->ds_vdata = skb->data;
 
-	/* setup rx descriptors */
+	/* setup rx descriptors. The sc_rxbufsize here tells the harware
+	 * how much data it can DMA to us and that we are prepared
+	 * to process */
 	ath9k_hw_setuprxdesc(ah,
 			     ds,
-			     skb_tailroom(skb),   /* buffer size */
+			     sc->sc_rxbufsize,
 			     0);
 
 	if (sc->sc_rxlink == NULL)
@@ -398,6 +400,13 @@ static struct sk_buff *ath_rxbuf_alloc(struct ath_softc *sc,
 	 * in rx'd frames.
 	 */
 
+	/* Note: the kernel can allocate a value greater than
+	 * what we ask it to give us. We really only need 4 KB as that
+	 * is this hardware supports and in fact we need at least 3849
+	 * as that is the MAX AMSDU size this hardware supports.
+	 * Unfortunately this means we may get 8 KB here from the
+	 * kernel... and that is actually what is observed on some
+	 * systems :( */
 	skb = dev_alloc_skb(len + sc->sc_cachelsz - 1);
 	if (skb != NULL) {
 		off = ((unsigned long) skb->data) % sc->sc_cachelsz;
@@ -456,7 +465,7 @@ static int ath_rx_indicate(struct ath_softc *sc,
 	if (nskb != NULL) {
 		bf->bf_mpdu = nskb;
 		bf->bf_buf_addr = pci_map_single(sc->pdev, nskb->data,
-					 skb_end_pointer(nskb) - nskb->head,
+					 sc->sc_rxbufsize,
 					 PCI_DMA_FROMDEVICE);
 		bf->bf_dmacontext = bf->bf_buf_addr;
 		ATH_RX_CONTEXT(nskb)->ctx_rxbuf = bf;
@@ -542,7 +551,7 @@ int ath_rx_init(struct ath_softc *sc, int nbufs)
 
 			bf->bf_mpdu = skb;
 			bf->bf_buf_addr = pci_map_single(sc->pdev, skb->data,
-					 skb_end_pointer(skb) - skb->head,
+					 sc->sc_rxbufsize,
 					 PCI_DMA_FROMDEVICE);
 			bf->bf_dmacontext = bf->bf_buf_addr;
 			ATH_RX_CONTEXT(skb)->ctx_rxbuf = bf;
@@ -1007,7 +1016,7 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush)
 
 		pci_dma_sync_single_for_cpu(sc->pdev,
 					    bf->bf_buf_addr,
-					    skb_tailroom(skb),
+					    sc->sc_rxbufsize,
 					    PCI_DMA_FROMDEVICE);
 		pci_unmap_single(sc->pdev,
 				 bf->bf_buf_addr,
diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c
index dcce3542..7a9f901 100644
--- a/drivers/net/wireless/ipw2200.c
+++ b/drivers/net/wireless/ipw2200.c
@@ -3897,6 +3897,7 @@ static int ipw_disassociate(void *data)
 	if (!(priv->status & (STATUS_ASSOCIATED | STATUS_ASSOCIATING)))
 		return 0;
 	ipw_send_disassociate(data, 0);
+	netif_carrier_off(priv->net_dev);
 	return 1;
 }
 
@@ -10190,6 +10191,9 @@ static int ipw_tx_skb(struct ipw_priv *priv, struct ieee80211_txb *txb,
 	u16 remaining_bytes;
 	int fc;
 
+	if (!(priv->status & STATUS_ASSOCIATED))
+		goto drop;
+
 	hdr_len = ieee80211_get_hdrlen(le16_to_cpu(hdr->frame_ctl));
 	switch (priv->ieee->iw_mode) {
 	case IW_MODE_ADHOC:
diff --git a/drivers/net/wireless/iwlwifi/iwl-agn.c b/drivers/net/wireless/iwlwifi/iwl-agn.c
index 444c5cc..c4c0371 100644
--- a/drivers/net/wireless/iwlwifi/iwl-agn.c
+++ b/drivers/net/wireless/iwlwifi/iwl-agn.c
@@ -1384,9 +1384,11 @@ void iwl_rx_handle(struct iwl_priv *priv)
 
 		rxq->queue[i] = NULL;
 
-		pci_dma_sync_single_for_cpu(priv->pci_dev, rxb->aligned_dma_addr,
-					    priv->hw_params.rx_buf_size,
-					    PCI_DMA_FROMDEVICE);
+		dma_sync_single_range_for_cpu(
+				&priv->pci_dev->dev, rxb->real_dma_addr,
+				rxb->aligned_dma_addr - rxb->real_dma_addr,
+				priv->hw_params.rx_buf_size,
+				PCI_DMA_FROMDEVICE);
 		pkt = (struct iwl_rx_packet *)rxb->skb->data;
 
 		/* Reclaim a command buffer only if this packet is a response
diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c
index 4c312c55..01a8458 100644
--- a/drivers/net/wireless/iwlwifi/iwl-core.c
+++ b/drivers/net/wireless/iwlwifi/iwl-core.c
@@ -290,6 +290,9 @@ void iwl_clear_stations_table(struct iwl_priv *priv)
 	priv->num_stations = 0;
 	memset(priv->stations, 0, sizeof(priv->stations));
 
+	/* clean ucode key table bit map */
+	priv->ucode_key_table = 0;
+
 	spin_unlock_irqrestore(&priv->sta_lock, flags);
 }
 EXPORT_SYMBOL(iwl_clear_stations_table);
diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c
index 61797f3..26f7084 100644
--- a/drivers/net/wireless/iwlwifi/iwl-sta.c
+++ b/drivers/net/wireless/iwlwifi/iwl-sta.c
@@ -475,7 +475,7 @@ static int iwl_get_free_ucode_key_index(struct iwl_priv *priv)
 		if (!test_and_set_bit(i, &priv->ucode_key_table))
 			return i;
 
-	return -1;
+	return WEP_INVALID_OFFSET;
 }
 
 int iwl_send_static_wepkey_cmd(struct iwl_priv *priv, u8 send_if_empty)
@@ -620,6 +620,9 @@ static int iwl_set_wep_dynamic_key_info(struct iwl_priv *priv,
 	/* else, we are overriding an existing key => no need to allocated room
 	 * in uCode. */
 
+	WARN(priv->stations[sta_id].sta.key.key_offset == WEP_INVALID_OFFSET,
+		"no space for new kew");
+
 	priv->stations[sta_id].sta.key.key_flags = key_flags;
 	priv->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK;
 	priv->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK;
@@ -637,6 +640,7 @@ static int iwl_set_ccmp_dynamic_key_info(struct iwl_priv *priv,
 {
 	unsigned long flags;
 	__le16 key_flags = 0;
+	int ret;
 
 	key_flags |= (STA_KEY_FLG_CCMP | STA_KEY_FLG_MAP_KEY_MSK);
 	key_flags |= cpu_to_le16(keyconf->keyidx << STA_KEY_FLG_KEYID_POS);
@@ -664,14 +668,18 @@ static int iwl_set_ccmp_dynamic_key_info(struct iwl_priv *priv,
 	/* else, we are overriding an existing key => no need to allocated room
 	 * in uCode. */
 
+	WARN(priv->stations[sta_id].sta.key.key_offset == WEP_INVALID_OFFSET,
+		"no space for new kew");
+
 	priv->stations[sta_id].sta.key.key_flags = key_flags;
 	priv->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK;
 	priv->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK;
 
+	ret = iwl_send_add_sta(priv, &priv->stations[sta_id].sta, CMD_ASYNC);
+
 	spin_unlock_irqrestore(&priv->sta_lock, flags);
 
-	IWL_DEBUG_INFO("hwcrypto: modify ucode station key info\n");
-	return iwl_send_add_sta(priv, &priv->stations[sta_id].sta, CMD_ASYNC);
+	return ret;
 }
 
 static int iwl_set_tkip_dynamic_key_info(struct iwl_priv *priv,
@@ -696,6 +704,9 @@ static int iwl_set_tkip_dynamic_key_info(struct iwl_priv *priv,
 	/* else, we are overriding an existing key => no need to allocated room
 	 * in uCode. */
 
+	WARN(priv->stations[sta_id].sta.key.key_offset == WEP_INVALID_OFFSET,
+		"no space for new kew");
+
 	/* This copy is acutally not needed: we get the key with each TX */
 	memcpy(priv->stations[sta_id].keyinfo.key, keyconf->key, 16);
 
@@ -734,6 +745,13 @@ int iwl_remove_dynamic_key(struct iwl_priv *priv,
 		return 0;
 	}
 
+	if (priv->stations[sta_id].sta.key.key_offset == WEP_INVALID_OFFSET) {
+		IWL_WARNING("Removing wrong key %d 0x%x\n",
+			    keyconf->keyidx, key_flags);
+		spin_unlock_irqrestore(&priv->sta_lock, flags);
+		return 0;
+	}
+
 	if (!test_and_clear_bit(priv->stations[sta_id].sta.key.key_offset,
 		&priv->ucode_key_table))
 		IWL_ERROR("index %d not used in uCode key table.\n",
diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c
index fe1867b..cac732f 100644
--- a/drivers/net/wireless/zd1211rw/zd_mac.c
+++ b/drivers/net/wireless/zd1211rw/zd_mac.c
@@ -615,7 +615,7 @@ static int filter_ack(struct ieee80211_hw *hw, struct ieee80211_hdr *rx_hdr,
 		struct ieee80211_hdr *tx_hdr;
 
 		tx_hdr = (struct ieee80211_hdr *)skb->data;
-		if (likely(!compare_ether_addr(tx_hdr->addr2, rx_hdr->addr1)))
+		if (likely(!memcmp(tx_hdr->addr2, rx_hdr->addr1, ETH_ALEN)))
 		{
 			__skb_unlink(skb, q);
 			tx_status(hw, skb, IEEE80211_TX_STAT_ACK, stats->signal, 1);
diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c
index 8f63f4c..9aad608 100644
--- a/drivers/pci/pcie/aspm.c
+++ b/drivers/pci/pcie/aspm.c
@@ -16,6 +16,7 @@
 #include <linux/pm.h>
 #include <linux/init.h>
 #include <linux/slab.h>
+#include <linux/jiffies.h>
 #include <linux/pci-aspm.h>
 #include "../pci.h"
 
@@ -161,11 +162,12 @@ static void pcie_check_clock_pm(struct pci_dev *pdev)
  */
 static void pcie_aspm_configure_common_clock(struct pci_dev *pdev)
 {
-	int pos, child_pos;
+	int pos, child_pos, i = 0;
 	u16 reg16 = 0;
 	struct pci_dev *child_dev;
 	int same_clock = 1;
-
+	unsigned long start_jiffies;
+	u16 child_regs[8], parent_reg;
 	/*
 	 * all functions of a slot should have the same Slot Clock
 	 * Configuration, so just check one function
@@ -191,16 +193,19 @@ static void pcie_aspm_configure_common_clock(struct pci_dev *pdev)
 		child_pos = pci_find_capability(child_dev, PCI_CAP_ID_EXP);
 		pci_read_config_word(child_dev, child_pos + PCI_EXP_LNKCTL,
 			&reg16);
+		child_regs[i] = reg16;
 		if (same_clock)
 			reg16 |= PCI_EXP_LNKCTL_CCC;
 		else
 			reg16 &= ~PCI_EXP_LNKCTL_CCC;
 		pci_write_config_word(child_dev, child_pos + PCI_EXP_LNKCTL,
 			reg16);
+		i++;
 	}
 
 	/* Configure upstream component */
 	pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, &reg16);
+	parent_reg = reg16;
 	if (same_clock)
 		reg16 |= PCI_EXP_LNKCTL_CCC;
 	else
@@ -212,12 +217,30 @@ static void pcie_aspm_configure_common_clock(struct pci_dev *pdev)
 	pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, reg16);
 
 	/* Wait for link training end */
-	while (1) {
+	/* break out after waiting for 1 second */
+	start_jiffies = jiffies;
+	while ((jiffies - start_jiffies) < HZ) {
 		pci_read_config_word(pdev, pos + PCI_EXP_LNKSTA, &reg16);
 		if (!(reg16 & PCI_EXP_LNKSTA_LT))
 			break;
 		cpu_relax();
 	}
+	/* training failed -> recover */
+	if ((jiffies - start_jiffies) >= HZ) {
+		dev_printk (KERN_ERR, &pdev->dev, "ASPM: Could not configure"
+			    " common clock\n");
+		i = 0;
+		list_for_each_entry(child_dev, &pdev->subordinate->devices,
+				    bus_list) {
+			child_pos = pci_find_capability(child_dev,
+							PCI_CAP_ID_EXP);
+			pci_write_config_word(child_dev,
+					      child_pos + PCI_EXP_LNKCTL,
+					      child_regs[i]);
+			i++;
+		}
+		pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, parent_reg);
+	}
 }
 
 /*
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 5049a47..5f4f85f 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -22,6 +22,7 @@
 #include <linux/delay.h>
 #include <linux/acpi.h>
 #include <linux/kallsyms.h>
+#include <linux/dmi.h>
 #include "pci.h"
 
 int isa_dma_bridge_buggy;
@@ -1828,6 +1829,22 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS,
 			 PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB,
 			 ht_enable_msi_mapping);
 
+/* The P5N32-SLI Premium motherboard from Asus has a problem with msi
+ * for the MCP55 NIC. It is not yet determined whether the msi problem
+ * also affects other devices. As for now, turn off msi for this device.
+ */
+static void __devinit nvenet_msi_disable(struct pci_dev *dev)
+{
+	if (dmi_name_in_vendors("P5N32-SLI PREMIUM")) {
+		dev_info(&dev->dev,
+			 "Disabling msi for MCP55 NIC on P5N32-SLI Premium\n");
+		dev->no_msi = 1;
+	}
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
+			PCI_DEVICE_ID_NVIDIA_NVENET_15,
+			nvenet_msi_disable);
+
 static void __devinit nv_msi_ht_cap_quirk(struct pci_dev *dev)
 {
 	struct pci_dev *host_bridge;
diff --git a/drivers/pci/slot.c b/drivers/pci/slot.c
index 4dd1c3e..5a8ccb4 100644
--- a/drivers/pci/slot.c
+++ b/drivers/pci/slot.c
@@ -253,6 +253,7 @@ placeholder:
 		 __func__, pci_domain_nr(parent), parent->number, slot_nr);
 
 out:
+	kfree(slot_name);
 	up_write(&pci_bus_sem);
 	return slot;
 err:
diff --git a/drivers/rtc/rtc-ds1672.c b/drivers/rtc/rtc-ds1672.c
index 341d7a5..4e91419 100644
--- a/drivers/rtc/rtc-ds1672.c
+++ b/drivers/rtc/rtc-ds1672.c
@@ -209,12 +209,18 @@ static int ds1672_probe(struct i2c_client *client,
 	return err;
 }
 
+static struct i2c_device_id ds1672_id[] = {
+	{ "ds1672", 0 },
+	{ }
+};
+
 static struct i2c_driver ds1672_driver = {
 	.driver = {
 		   .name = "rtc-ds1672",
 		   },
 	.probe = &ds1672_probe,
 	.remove = &ds1672_remove,
+	.id_table = ds1672_id,
 };
 
 static int __init ds1672_init(void)
diff --git a/drivers/rtc/rtc-max6900.c b/drivers/rtc/rtc-max6900.c
index 8078279..a4f6665 100644
--- a/drivers/rtc/rtc-max6900.c
+++ b/drivers/rtc/rtc-max6900.c
@@ -247,12 +247,18 @@ max6900_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	return 0;
 }
 
+static struct i2c_device_id max6900_id[] = {
+	{ "max6900", 0 },
+	{ }
+};
+
 static struct i2c_driver max6900_driver = {
 	.driver = {
 		   .name = "rtc-max6900",
 		   },
 	.probe = max6900_probe,
 	.remove = max6900_remove,
+	.id_table = max6900_id,
 };
 
 static int __init max6900_init(void)
diff --git a/drivers/rtc/rtc-starfire.c b/drivers/rtc/rtc-starfire.c
index 7ccb0dd..5be98bf 100644
--- a/drivers/rtc/rtc-starfire.c
+++ b/drivers/rtc/rtc-starfire.c
@@ -6,7 +6,6 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
-#include <linux/time.h>
 #include <linux/rtc.h>
 #include <linux/platform_device.h>
 
@@ -16,11 +15,6 @@ MODULE_AUTHOR("David S. Miller <davem@davemloft.net>");
 MODULE_DESCRIPTION("Starfire RTC driver");
 MODULE_LICENSE("GPL");
 
-struct starfire_rtc {
-	struct rtc_device	*rtc;
-	spinlock_t		lock;
-};
-
 static u32 starfire_get_time(void)
 {
 	static char obp_gettod[32];
@@ -35,64 +29,31 @@ static u32 starfire_get_time(void)
 
 static int starfire_read_time(struct device *dev, struct rtc_time *tm)
 {
-	struct starfire_rtc *p = dev_get_drvdata(dev);
-	unsigned long flags, secs;
-
-	spin_lock_irqsave(&p->lock, flags);
-	secs = starfire_get_time();
-	spin_unlock_irqrestore(&p->lock, flags);
-
-	rtc_time_to_tm(secs, tm);
-
-	return 0;
-}
-
-static int starfire_set_time(struct device *dev, struct rtc_time *tm)
-{
-	unsigned long secs;
-	int err;
-
-	err = rtc_tm_to_time(tm, &secs);
-	if (err)
-		return err;
-
-	/* Do nothing, time is set using the service processor
-	 * console on this platform.
-	 */
-	return 0;
+	rtc_time_to_tm(starfire_get_time(), tm);
+	return rtc_valid_tm(tm);
 }
 
 static const struct rtc_class_ops starfire_rtc_ops = {
 	.read_time	= starfire_read_time,
-	.set_time	= starfire_set_time,
 };
 
-static int __devinit starfire_rtc_probe(struct platform_device *pdev)
+static int __init starfire_rtc_probe(struct platform_device *pdev)
 {
-	struct starfire_rtc *p = kzalloc(sizeof(*p), GFP_KERNEL);
-
-	if (!p)
-		return -ENOMEM;
+	struct rtc_device *rtc = rtc_device_register("starfire", &pdev->dev,
+				     &starfire_rtc_ops, THIS_MODULE);
+	if (IS_ERR(rtc))
+		return PTR_ERR(rtc);
 
-	spin_lock_init(&p->lock);
+	platform_set_drvdata(pdev, rtc);
 
-	p->rtc = rtc_device_register("starfire", &pdev->dev,
-				     &starfire_rtc_ops, THIS_MODULE);
-	if (IS_ERR(p->rtc)) {
-		int err = PTR_ERR(p->rtc);
-		kfree(p);
-		return err;
-	}
-	platform_set_drvdata(pdev, p);
 	return 0;
 }
 
-static int __devexit starfire_rtc_remove(struct platform_device *pdev)
+static int __exit starfire_rtc_remove(struct platform_device *pdev)
 {
-	struct starfire_rtc *p = platform_get_drvdata(pdev);
+	struct rtc_device *rtc = platform_get_drvdata(pdev);
 
-	rtc_device_unregister(p->rtc);
-	kfree(p);
+	rtc_device_unregister(rtc);
 
 	return 0;
 }
@@ -102,13 +63,12 @@ static struct platform_driver starfire_rtc_driver = {
 		.name	= "rtc-starfire",
 		.owner	= THIS_MODULE,
 	},
-	.probe		= starfire_rtc_probe,
-	.remove		= __devexit_p(starfire_rtc_remove),
+	.remove		= __exit_p(starfire_rtc_remove),
 };
 
 static int __init starfire_rtc_init(void)
 {
-	return platform_driver_register(&starfire_rtc_driver);
+	return platform_driver_probe(&starfire_rtc_driver, starfire_rtc_probe);
 }
 
 static void __exit starfire_rtc_exit(void)
diff --git a/drivers/rtc/rtc-twl4030.c b/drivers/rtc/rtc-twl4030.c
index abe87a4..01d8da9 100644
--- a/drivers/rtc/rtc-twl4030.c
+++ b/drivers/rtc/rtc-twl4030.c
@@ -337,7 +337,7 @@ static int twl4030_rtc_ioctl(struct device *dev, unsigned int cmd,
 }
 
 #else
-#define	omap_rtc_ioctl	NULL
+#define	twl4030_rtc_ioctl	NULL
 #endif
 
 static irqreturn_t twl4030_rtc_interrupt(int irq, void *rtc)
diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c
index 35364f6..c557ba34e1 100644
--- a/drivers/s390/scsi/zfcp_erp.c
+++ b/drivers/s390/scsi/zfcp_erp.c
@@ -720,7 +720,6 @@ static int zfcp_erp_adapter_strategy_generic(struct zfcp_erp_action *act,
 		goto failed_openfcp;
 
 	atomic_set_mask(ZFCP_STATUS_COMMON_OPEN, &act->adapter->status);
-	schedule_work(&act->adapter->scan_work);
 
 	return ZFCP_ERP_SUCCEEDED;
 
@@ -1186,7 +1185,9 @@ static void zfcp_erp_scsi_scan(struct work_struct *work)
 		container_of(work, struct zfcp_erp_add_work, work);
 	struct zfcp_unit *unit = p->unit;
 	struct fc_rport *rport = unit->port->rport;
-	scsi_scan_target(&rport->dev, 0, rport->scsi_target_id,
+
+	if (rport && rport->port_state == FC_PORTSTATE_ONLINE)
+		scsi_scan_target(&rport->dev, 0, rport->scsi_target_id,
 			 scsilun_to_int((struct scsi_lun *)&unit->fcp_lun), 0);
 	atomic_clear_mask(ZFCP_STATUS_UNIT_SCSI_WORK_PENDING, &unit->status);
 	zfcp_unit_put(unit);
@@ -1282,6 +1283,8 @@ static void zfcp_erp_action_cleanup(struct zfcp_erp_action *act, int result)
 	case ZFCP_ERP_ACTION_REOPEN_ADAPTER:
 		if (result != ZFCP_ERP_SUCCEEDED)
 			zfcp_erp_rports_del(adapter);
+		else
+			schedule_work(&adapter->scan_work);
 		zfcp_adapter_put(adapter);
 		break;
 	}
diff --git a/drivers/s390/scsi/zfcp_fc.c b/drivers/s390/scsi/zfcp_fc.c
index 1a7c80a..8aab309 100644
--- a/drivers/s390/scsi/zfcp_fc.c
+++ b/drivers/s390/scsi/zfcp_fc.c
@@ -50,7 +50,8 @@ static int zfcp_wka_port_get(struct zfcp_wka_port *wka_port)
 	if (mutex_lock_interruptible(&wka_port->mutex))
 		return -ERESTARTSYS;
 
-	if (wka_port->status != ZFCP_WKA_PORT_ONLINE) {
+	if (wka_port->status == ZFCP_WKA_PORT_OFFLINE ||
+	    wka_port->status == ZFCP_WKA_PORT_CLOSING) {
 		wka_port->status = ZFCP_WKA_PORT_OPENING;
 		if (zfcp_fsf_open_wka_port(wka_port))
 			wka_port->status = ZFCP_WKA_PORT_OFFLINE;
@@ -125,8 +126,7 @@ static void _zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req, u32 range,
 
 	read_lock_irqsave(&zfcp_data.config_lock, flags);
 	list_for_each_entry(port, &fsf_req->adapter->port_list_head, list) {
-		/* FIXME: ZFCP_STATUS_PORT_DID_DID check is racy */
-		if (!(atomic_read(&port->status) & ZFCP_STATUS_PORT_DID_DID))
+		if (!(atomic_read(&port->status) & ZFCP_STATUS_PORT_PHYS_OPEN))
 			/* Try to connect to unused ports anyway. */
 			zfcp_erp_port_reopen(port,
 					     ZFCP_STATUS_COMMON_ERP_FAILED,
@@ -610,7 +610,6 @@ int zfcp_scan_ports(struct zfcp_adapter *adapter)
 	int ret, i;
 	struct zfcp_gpn_ft *gpn_ft;
 
-	zfcp_erp_wait(adapter); /* wait until adapter is finished with ERP */
 	if (fc_host_port_type(adapter->scsi_host) != FC_PORTTYPE_NPORT)
 		return 0;
 
diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index d024442..dc03676 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -930,8 +930,10 @@ struct zfcp_fsf_req *zfcp_fsf_abort_fcp_command(unsigned long old_req_id,
 		goto out;
 	req = zfcp_fsf_req_create(adapter, FSF_QTCB_ABORT_FCP_CMND,
 				  req_flags, adapter->pool.fsf_req_abort);
-	if (IS_ERR(req))
+	if (IS_ERR(req)) {
+		req = NULL;
 		goto out;
+	}
 
 	if (unlikely(!(atomic_read(&unit->status) &
 		       ZFCP_STATUS_COMMON_UNBLOCKED)))
@@ -1584,6 +1586,7 @@ static void zfcp_fsf_open_wka_port_handler(struct zfcp_fsf_req *req)
 		wka_port->status = ZFCP_WKA_PORT_OFFLINE;
 		break;
 	case FSF_PORT_ALREADY_OPEN:
+		break;
 	case FSF_GOOD:
 		wka_port->handle = header->port_handle;
 		wka_port->status = ZFCP_WKA_PORT_ONLINE;
@@ -2113,18 +2116,21 @@ static inline void zfcp_fsf_trace_latency(struct zfcp_fsf_req *fsf_req)
 
 static void zfcp_fsf_send_fcp_command_task_handler(struct zfcp_fsf_req *req)
 {
-	struct scsi_cmnd *scpnt = req->data;
+	struct scsi_cmnd *scpnt;
 	struct fcp_rsp_iu *fcp_rsp_iu = (struct fcp_rsp_iu *)
 	    &(req->qtcb->bottom.io.fcp_rsp);
 	u32 sns_len;
 	char *fcp_rsp_info = (unsigned char *) &fcp_rsp_iu[1];
 	unsigned long flags;
 
-	if (unlikely(!scpnt))
-		return;
-
 	read_lock_irqsave(&req->adapter->abort_lock, flags);
 
+	scpnt = req->data;
+	if (unlikely(!scpnt)) {
+		read_unlock_irqrestore(&req->adapter->abort_lock, flags);
+		return;
+	}
+
 	if (unlikely(req->status & ZFCP_STATUS_FSFREQ_ABORTED)) {
 		set_host_byte(scpnt, DID_SOFT_ERROR);
 		set_driver_byte(scpnt, SUGGEST_RETRY);
@@ -2442,8 +2448,10 @@ struct zfcp_fsf_req *zfcp_fsf_send_fcp_ctm(struct zfcp_adapter *adapter,
 		goto out;
 	req = zfcp_fsf_req_create(adapter, FSF_QTCB_FCP_CMND, req_flags,
 				  adapter->pool.fsf_req_scsi);
-	if (IS_ERR(req))
+	if (IS_ERR(req)) {
+		req = NULL;
 		goto out;
+	}
 
 	req->status |= ZFCP_STATUS_FSFREQ_TASK_MANAGEMENT;
 	req->data = unit;
diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c
index e46fd3e..468c880 100644
--- a/drivers/s390/scsi/zfcp_scsi.c
+++ b/drivers/s390/scsi/zfcp_scsi.c
@@ -88,7 +88,7 @@ static int zfcp_scsi_queuecommand(struct scsi_cmnd *scpnt,
 	ret = zfcp_fsf_send_fcp_command_task(adapter, unit, scpnt, 0,
 					     ZFCP_REQ_AUTO_CLEANUP);
 	if (unlikely(ret == -EBUSY))
-		zfcp_scsi_command_fail(scpnt, DID_NO_CONNECT);
+		return SCSI_MLQUEUE_DEVICE_BUSY;
 	else if (unlikely(ret < 0))
 		return SCSI_MLQUEUE_HOST_BUSY;
 
diff --git a/drivers/scsi/aacraid/linit.c b/drivers/scsi/aacraid/linit.c
index 9aa301c..162cd92 100644
--- a/drivers/scsi/aacraid/linit.c
+++ b/drivers/scsi/aacraid/linit.c
@@ -427,8 +427,8 @@ static int aac_slave_configure(struct scsi_device *sdev)
 		 * Firmware has an individual device recovery time typically
 		 * of 35 seconds, give us a margin.
 		 */
-		if (sdev->timeout < (45 * HZ))
-			sdev->timeout = 45 * HZ;
+		if (sdev->request_queue->rq_timeout < (45 * HZ))
+			blk_queue_rq_timeout(sdev->request_queue, 45*HZ);
 		for (cid = 0; cid < aac->maximum_num_containers; ++cid)
 			if (aac->fsa_dev[cid].valid)
 				++num_lsu;
diff --git a/drivers/scsi/ibmvscsi/ibmvscsi.c b/drivers/scsi/ibmvscsi/ibmvscsi.c
index 87e09f3..6cad175 100644
--- a/drivers/scsi/ibmvscsi/ibmvscsi.c
+++ b/drivers/scsi/ibmvscsi/ibmvscsi.c
@@ -1442,7 +1442,7 @@ static int ibmvscsi_slave_configure(struct scsi_device *sdev)
 	spin_lock_irqsave(shost->host_lock, lock_flags);
 	if (sdev->type == TYPE_DISK) {
 		sdev->allow_restart = 1;
-		sdev->timeout = 60 * HZ;
+		blk_queue_rq_timeout(sdev->request_queue, 60 * HZ);
 	}
 	scsi_adjust_queue_depth(sdev, 0, shost->cmd_per_lun);
 	spin_unlock_irqrestore(shost->host_lock, lock_flags);
diff --git a/drivers/scsi/megaraid/megaraid_sas.c b/drivers/scsi/megaraid/megaraid_sas.c
index a454f94..17ce7ab 100644
--- a/drivers/scsi/megaraid/megaraid_sas.c
+++ b/drivers/scsi/megaraid/megaraid_sas.c
@@ -1016,7 +1016,8 @@ static int megasas_slave_configure(struct scsi_device *sdev)
 	 * The RAID firmware may require extended timeouts.
 	 */
 	if (sdev->channel >= MEGASAS_MAX_PD_CHANNELS)
-		sdev->timeout = MEGASAS_DEFAULT_CMD_TIMEOUT * HZ;
+		blk_queue_rq_timeout(sdev->request_queue,
+				     MEGASAS_DEFAULT_CMD_TIMEOUT * HZ);
 	return 0;
 }
 
diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
index 3863617..edfaf24 100644
--- a/drivers/scsi/scsi_error.c
+++ b/drivers/scsi/scsi_error.c
@@ -932,8 +932,7 @@ static int scsi_eh_try_stu(struct scsi_cmnd *scmd)
 		int i, rtn = NEEDS_RETRY;
 
 		for (i = 0; rtn == NEEDS_RETRY && i < 2; i++)
-			rtn = scsi_send_eh_cmnd(scmd, stu_command, 6,
-						scmd->device->timeout, 0);
+			rtn = scsi_send_eh_cmnd(scmd, stu_command, 6, scmd->device->request_queue->rq_timeout, 0);
 
 		if (rtn == SUCCESS)
 			return 0;
diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index f5d3b96..fa45a1a 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -567,15 +567,18 @@ static inline int scsi_host_is_busy(struct Scsi_Host *shost)
  */
 static void scsi_run_queue(struct request_queue *q)
 {
-	struct scsi_device *starved_head = NULL, *sdev = q->queuedata;
+	struct scsi_device *sdev = q->queuedata;
 	struct Scsi_Host *shost = sdev->host;
+	LIST_HEAD(starved_list);
 	unsigned long flags;
 
 	if (scsi_target(sdev)->single_lun)
 		scsi_single_lun_run(sdev);
 
 	spin_lock_irqsave(shost->host_lock, flags);
-	while (!list_empty(&shost->starved_list) && !scsi_host_is_busy(shost)) {
+	list_splice_init(&shost->starved_list, &starved_list);
+
+	while (!list_empty(&starved_list)) {
 		int flagset;
 
 		/*
@@ -588,24 +591,18 @@ static void scsi_run_queue(struct request_queue *q)
 		 * scsi_request_fn must get the host_lock before checking
 		 * or modifying starved_list or starved_entry.
 		 */
-		sdev = list_entry(shost->starved_list.next,
-					  struct scsi_device, starved_entry);
-		/*
-		 * The *queue_ready functions can add a device back onto the
-		 * starved list's tail, so we must check for a infinite loop.
-		 */
-		if (sdev == starved_head)
+		if (scsi_host_is_busy(shost))
 			break;
-		if (!starved_head)
-			starved_head = sdev;
 
+		sdev = list_entry(starved_list.next,
+				  struct scsi_device, starved_entry);
+		list_del_init(&sdev->starved_entry);
 		if (scsi_target_is_busy(scsi_target(sdev))) {
 			list_move_tail(&sdev->starved_entry,
 				       &shost->starved_list);
 			continue;
 		}
 
-		list_del_init(&sdev->starved_entry);
 		spin_unlock(shost->host_lock);
 
 		spin_lock(sdev->request_queue->queue_lock);
@@ -621,6 +618,8 @@ static void scsi_run_queue(struct request_queue *q)
 
 		spin_lock(shost->host_lock);
 	}
+	/* put any unprocessed entries back */
+	list_splice(&starved_list, &shost->starved_list);
 	spin_unlock_irqrestore(shost->host_lock, flags);
 
 	blk_run_queue(q);
diff --git a/drivers/scsi/sd.c b/drivers/scsi/sd.c
index c9e1242..5081b39 100644
--- a/drivers/scsi/sd.c
+++ b/drivers/scsi/sd.c
@@ -757,7 +757,7 @@ static int sd_ioctl(struct block_device *bdev, fmode_t mode,
 	 * access to the device is prohibited.
 	 */
 	error = scsi_nonblockable_ioctl(sdp, cmd, p,
-					(mode & FMODE_NDELAY_NOW) != 0);
+					(mode & FMODE_NDELAY) != 0);
 	if (!scsi_block_when_processing_errors(sdp) || !error)
 		return error;
 
diff --git a/drivers/scsi/sr.c b/drivers/scsi/sr.c
index 62b6633..45b66b9 100644
--- a/drivers/scsi/sr.c
+++ b/drivers/scsi/sr.c
@@ -521,7 +521,7 @@ static int sr_block_ioctl(struct block_device *bdev, fmode_t mode, unsigned cmd,
 	 * if it doesn't recognise the ioctl
 	 */
 	ret = scsi_nonblockable_ioctl(sdev, cmd, argp,
-					(mode & FMODE_NDELAY_NOW) != 0);
+					(mode & FMODE_NDELAY) != 0);
 	if (ret != -ENODEV)
 		return ret;
 	return scsi_ioctl(sdev, cmd, argp);
diff --git a/drivers/scsi/stex.c b/drivers/scsi/stex.c
index 3790906..2fa830c 100644
--- a/drivers/scsi/stex.c
+++ b/drivers/scsi/stex.c
@@ -477,7 +477,7 @@ stex_slave_config(struct scsi_device *sdev)
 {
 	sdev->use_10_for_rw = 1;
 	sdev->use_10_for_ms = 1;
-	sdev->timeout = 60 * HZ;
+	blk_queue_rq_timeout(sdev->request_queue, 60 * HZ);
 	sdev->tagged_supported = 1;
 
 	return 0;
diff --git a/drivers/serial/ioc3_serial.c b/drivers/serial/ioc3_serial.c
index 6dd98f9..ae3699d 100644
--- a/drivers/serial/ioc3_serial.c
+++ b/drivers/serial/ioc3_serial.c
@@ -2149,7 +2149,7 @@ out4:
 	return ret;
 }
 
-static struct ioc3_submodule ioc3uart_submodule = {
+static struct ioc3_submodule ioc3uart_ops = {
 	.name = "IOC3uart",
 	.probe = ioc3uart_probe,
 	.remove = ioc3uart_remove,
@@ -2173,7 +2173,7 @@ static int __devinit ioc3uart_init(void)
 		       __func__);
 		return ret;
 	}
-	ret = ioc3_register_submodule(&ioc3uart_submodule);
+	ret = ioc3_register_submodule(&ioc3uart_ops);
 	if (ret)
 		uart_unregister_driver(&ioc3_uart);
 	return ret;
@@ -2181,7 +2181,7 @@ static int __devinit ioc3uart_init(void)
 
 static void __devexit ioc3uart_exit(void)
 {
-	ioc3_unregister_submodule(&ioc3uart_submodule);
+	ioc3_unregister_submodule(&ioc3uart_ops);
 	uart_unregister_driver(&ioc3_uart);
 }
 
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 6117d3d..28c00c3 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -591,8 +591,8 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 	/* Update the per-port timeout */
 	uart_update_timeout(port, new->c_cflag, baud);
 
-	/* Do our best to flush TX & RX, so we don't loose anything */
-	/* But we don't wait indefinitly ! */
+	/* Do our best to flush TX & RX, so we don't lose anything */
+	/* But we don't wait indefinitely ! */
 	j = 5000000;	/* Maximum wait */
 	/* FIXME Can't receive chars since set_termios might be called at early
 	 * boot for the console, all stuff is not yet ready to receive at that
diff --git a/drivers/serial/s3c2440.c b/drivers/serial/s3c2440.c
index 317d239..29cbb0a 100644
--- a/drivers/serial/s3c2440.c
+++ b/drivers/serial/s3c2440.c
@@ -177,5 +177,5 @@ module_exit(s3c2440_serial_exit);
 
 MODULE_DESCRIPTION("Samsung S3C2440,S3C2442 SoC Serial port driver");
 MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_LICENSE("GPLi v2");
+MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("platform:s3c2440-uart");
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index 91697bd..4bbddb7 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -18,6 +18,7 @@
 #include <linux/jiffies.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
+#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 #include <asm/io.h>
@@ -25,7 +26,6 @@
 
 #include <mach/mux.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
 #include <mach/fpga.h>
 #include <mach/usb.h>
 
@@ -254,8 +254,8 @@ static int ohci_omap_init(struct usb_hcd *hcd)
 
 			/* gpio9 for overcurrent detction */
 			omap_cfg_reg(W8_1610_GPIO9);
-			omap_request_gpio(9);
-			omap_set_gpio_direction(9, 1 /* IN */);
+			gpio_request(9, "OHCI overcurrent");
+			gpio_direction_input(9);
 
 			/* for paranoia's sake:  disable USB.PUEN */
 			omap_cfg_reg(W4_USB_HIGHZ);
@@ -407,7 +407,7 @@ usb_hcd_omap_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 		put_device(ohci->transceiver->dev);
 	}
 	if (machine_is_omap_osk())
-		omap_free_gpio(9);
+		gpio_free(9);
 	iounmap(hcd->regs);
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 	usb_put_hcd(hcd);
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 51d7bde..aad1359 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -1498,7 +1498,7 @@ static int ftdi_open(struct tty_struct *tty,
 			priv->interface, buf, 0, WDR_TIMEOUT);
 
 	/* Termios defaults are set by usb_serial_init. We don't change
-	   port->tty->termios - this would loose speed settings, etc.
+	   port->tty->termios - this would lose speed settings, etc.
 	   This is same behaviour as serial.c/rs_open() - Kuba */
 
 	/* ftdi_set_termios  will send usb control messages */
diff --git a/drivers/video/aty/radeon_accel.c b/drivers/video/aty/radeon_accel.c
index a547e5d..8da5e5a 100644
--- a/drivers/video/aty/radeon_accel.c
+++ b/drivers/video/aty/radeon_accel.c
@@ -256,7 +256,8 @@ void radeonfb_imageblit(struct fb_info *info, const struct fb_image *image)
 		return;
 
 	/* We only do 1 bpp color expansion for now */
-	if (info->flags & FBINFO_HWACCEL_DISABLED || image->depth != 1)
+	if (!accel_cexp ||
+	    (info->flags & FBINFO_HWACCEL_DISABLED) || image->depth != 1)
 		goto fallback;
 
 	/* Fallback if running out of the screen. We may do clipping
diff --git a/drivers/video/aty/radeon_base.c b/drivers/video/aty/radeon_base.c
index b3ffe82..d5b27f9 100644
--- a/drivers/video/aty/radeon_base.c
+++ b/drivers/video/aty/radeon_base.c
@@ -282,6 +282,8 @@ static int backlight = 1;
 static int backlight = 0;
 #endif
 
+int accel_cexp = 0;
+
 /*
  * prototypes
  */
@@ -2520,6 +2522,8 @@ static int __init radeonfb_setup (char *options)
 		} else if (!strncmp(this_opt, "ignore_devlist", 14)) {
 			ignore_devlist = 1;
 #endif
+		} else if (!strncmp(this_opt, "accel_cexp", 12)) {
+			accel_cexp = 1;
 		} else
 			mode_option = this_opt;
 	}
@@ -2567,6 +2571,8 @@ module_param(monitor_layout, charp, 0);
 MODULE_PARM_DESC(monitor_layout, "Specify monitor mapping (like XFree86)");
 module_param(force_measure_pll, bool, 0);
 MODULE_PARM_DESC(force_measure_pll, "Force measurement of PLL (debug)");
+module_param(accel_cexp, bool, 0);
+MODULE_PARM_DESC(accel_cexp, "Use acceleration engine for color expansion");
 #ifdef CONFIG_MTRR
 module_param(nomtrr, bool, 0);
 MODULE_PARM_DESC(nomtrr, "bool: disable use of MTRR registers");
diff --git a/drivers/video/aty/radeonfb.h b/drivers/video/aty/radeonfb.h
index ea0b5b4..974ca6d 100644
--- a/drivers/video/aty/radeonfb.h
+++ b/drivers/video/aty/radeonfb.h
@@ -638,4 +638,6 @@ static inline void radeonfb_bl_init(struct radeonfb_info *rinfo) {}
 static inline void radeonfb_bl_exit(struct radeonfb_info *rinfo) {}
 #endif
 
+extern int accel_cexp;
+
 #endif /* __RADEONFB_H__ */
diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c
index 67ff370..0b2adef 100644
--- a/drivers/video/console/fbcon.c
+++ b/drivers/video/console/fbcon.c
@@ -3531,12 +3531,18 @@ static void fbcon_exit(void)
 	softback_buf = 0UL;
 
 	for (i = 0; i < FB_MAX; i++) {
+		int pending;
+
 		mapped = 0;
 		info = registered_fb[i];
 
 		if (info == NULL)
 			continue;
 
+		pending = cancel_work_sync(&info->queue);
+		DPRINTK("fbcon: %s pending work\n", (pending ? "canceled" :
+			"no"));
+
 		for (j = first_fb_vc; j <= last_fb_vc; j++) {
 			if (con2fb_map[j] == i)
 				mapped = 1;
diff --git a/drivers/video/macfb.c b/drivers/video/macfb.c
index b790ddf..ee380d5 100644
--- a/drivers/video/macfb.c
+++ b/drivers/video/macfb.c
@@ -164,7 +164,6 @@ static struct fb_var_screeninfo macfb_defined = {
 };
 
 static struct fb_fix_screeninfo macfb_fix = {
-	.id	= "Macintosh ",
 	.type	= FB_TYPE_PACKED_PIXELS,
 	.accel	= FB_ACCEL_NONE,
 };
@@ -760,22 +759,22 @@ static int __init macfb_init(void)
 
 		switch(ndev->dr_hw) {
 		case NUBUS_DRHW_APPLE_MDC:
-			strcat( macfb_fix.id, "Display Card" );
+			strcpy(macfb_fix.id, "Mac Disp. Card");
 			macfb_setpalette = mdc_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
 			break;
 		case NUBUS_DRHW_APPLE_TFB:
-			strcat( macfb_fix.id, "Toby" );
+			strcpy(macfb_fix.id, "Toby");
 			macfb_setpalette = toby_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
 			break;
 		case NUBUS_DRHW_APPLE_JET:
-			strcat( macfb_fix.id, "Jet");
+			strcpy(macfb_fix.id, "Jet");
 			macfb_setpalette = jet_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
 			break;			
 		default:
-			strcat( macfb_fix.id, "Generic NuBus" );
+			strcpy(macfb_fix.id, "Generic NuBus");
 			break;
 		}
 	}
@@ -786,21 +785,11 @@ static int __init macfb_init(void)
 	if (!video_is_nubus)
 		switch( mac_bi_data.id )
 		{
-			/* These don't have onboard video.  Eventually, we may
-			   be able to write separate framebuffer drivers for
-			   them (tobyfb.c, hiresfb.c, etc, etc) */
-		case MAC_MODEL_II:
-		case MAC_MODEL_IIX:
-		case MAC_MODEL_IICX:
-		case MAC_MODEL_IIFX:
-			strcat( macfb_fix.id, "Generic NuBus" );
-			break;
-
 			/* Valkyrie Quadras */
 		case MAC_MODEL_Q630:
 			/* I'm not sure about this one */
 		case MAC_MODEL_P588:
-			strcat( macfb_fix.id, "Valkyrie built-in" );
+			strcpy(macfb_fix.id, "Valkyrie");
 			macfb_setpalette = valkyrie_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
 			valkyrie_cmap_regs = ioremap(DAC_BASE, 0x1000);
@@ -823,7 +812,7 @@ static int __init macfb_init(void)
 		case MAC_MODEL_Q700:
 		case MAC_MODEL_Q900:
 		case MAC_MODEL_Q950:
-			strcat( macfb_fix.id, "DAFB built-in" );
+			strcpy(macfb_fix.id, "DAFB");
 			macfb_setpalette = dafb_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
 			dafb_cmap_regs = ioremap(DAFB_BASE, 0x1000);
@@ -831,7 +820,7 @@ static int __init macfb_init(void)
 
 			/* LC II uses the V8 framebuffer */
 		case MAC_MODEL_LCII:
-			strcat( macfb_fix.id, "V8 built-in" );
+			strcpy(macfb_fix.id, "V8");
 			macfb_setpalette = v8_brazil_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
 			v8_brazil_cmap_regs = ioremap(DAC_BASE, 0x1000);
@@ -843,7 +832,7 @@ static int __init macfb_init(void)
 		case MAC_MODEL_IIVI:
 		case MAC_MODEL_IIVX:
 		case MAC_MODEL_P600:
-			strcat( macfb_fix.id, "Brazil built-in" );
+			strcpy(macfb_fix.id, "Brazil");
 			macfb_setpalette = v8_brazil_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
 			v8_brazil_cmap_regs = ioremap(DAC_BASE, 0x1000);
@@ -860,7 +849,7 @@ static int __init macfb_init(void)
 		case MAC_MODEL_P460:
 			macfb_setpalette = v8_brazil_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
-			strcat( macfb_fix.id, "Sonora built-in" );
+			strcpy(macfb_fix.id, "Sonora");
 			v8_brazil_cmap_regs = ioremap(DAC_BASE, 0x1000);
 			break;
 
@@ -871,7 +860,7 @@ static int __init macfb_init(void)
 		case MAC_MODEL_IISI:
 			macfb_setpalette = rbv_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
-			strcat( macfb_fix.id, "RBV built-in" );
+			strcpy(macfb_fix.id, "RBV");
 			rbv_cmap_regs = ioremap(DAC_BASE, 0x1000);
 			break;
 
@@ -880,7 +869,7 @@ static int __init macfb_init(void)
 		case MAC_MODEL_C660:
 			macfb_setpalette = civic_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
-			strcat( macfb_fix.id, "Civic built-in" );
+			strcpy(macfb_fix.id, "Civic");
 			civic_cmap_regs = ioremap(CIVIC_BASE, 0x1000);
 			break;
 
@@ -901,7 +890,7 @@ static int __init macfb_init(void)
 				v8_brazil_cmap_regs =
 					ioremap(DAC_BASE, 0x1000);
 			}
-			strcat( macfb_fix.id, "LC built-in" );
+			strcpy(macfb_fix.id, "LC");
 			break;
 			/* We think this may be like the LC II */
 		case MAC_MODEL_CCL:
@@ -911,18 +900,18 @@ static int __init macfb_init(void)
 				v8_brazil_cmap_regs =
 					ioremap(DAC_BASE, 0x1000);
 			}
-			strcat( macfb_fix.id, "Color Classic built-in" );
+			strcpy(macfb_fix.id, "Color Classic");
 			break;
 
 			/* And we *do* mean "weirdos" */
 		case MAC_MODEL_TV:
-			strcat( macfb_fix.id, "Mac TV built-in" );
+			strcpy(macfb_fix.id, "Mac TV");
 			break;
 
 			/* These don't have colour, so no need to worry */
 		case MAC_MODEL_SE30:
 		case MAC_MODEL_CLII:
-			strcat( macfb_fix.id, "Monochrome built-in" );
+			strcpy(macfb_fix.id, "Monochrome");
 			break;
 
 			/* Powerbooks are particularly difficult.  Many of
@@ -935,7 +924,7 @@ static int __init macfb_init(void)
 		case MAC_MODEL_PB140:
 		case MAC_MODEL_PB145:
 		case MAC_MODEL_PB170:
-			strcat( macfb_fix.id, "DDC built-in" );
+			strcpy(macfb_fix.id, "DDC");
 			break;
 
 			/* Internal is GSC, External (if present) is ViSC */
@@ -945,13 +934,13 @@ static int __init macfb_init(void)
 		case MAC_MODEL_PB180:
 		case MAC_MODEL_PB210:
 		case MAC_MODEL_PB230:
-			strcat( macfb_fix.id, "GSC built-in" );
+			strcpy(macfb_fix.id, "GSC");
 			break;
 
 			/* Internal is TIM, External is ViSC */
 		case MAC_MODEL_PB165C:
 		case MAC_MODEL_PB180C:
-			strcat( macfb_fix.id, "TIM built-in" );
+			strcpy(macfb_fix.id, "TIM");
 			break;
 
 			/* Internal is CSC, External is Keystone+Ariel. */
@@ -963,12 +952,12 @@ static int __init macfb_init(void)
 		case MAC_MODEL_PB280C:
 			macfb_setpalette = csc_setpalette;
 			macfb_defined.activate = FB_ACTIVATE_NOW;
-			strcat( macfb_fix.id, "CSC built-in" );
+			strcpy(macfb_fix.id, "CSC");
 			csc_cmap_regs = ioremap(CSC_BASE, 0x1000);
 			break;
 		
 		default:
-			strcat( macfb_fix.id, "Unknown/Unsupported built-in" );
+			strcpy(macfb_fix.id, "Unknown");
 			break;
 		}
 
@@ -978,16 +967,23 @@ static int __init macfb_init(void)
 	fb_info.pseudo_palette	= pseudo_palette;
 	fb_info.flags		= FBINFO_DEFAULT;
 
-	fb_alloc_cmap(&fb_info.cmap, video_cmap_len, 0);
+	err = fb_alloc_cmap(&fb_info.cmap, video_cmap_len, 0);
+	if (err)
+		goto fail_unmap;
 	
 	err = register_framebuffer(&fb_info);
-	if (!err)
-		printk("fb%d: %s frame buffer device\n",
-		       fb_info.node, fb_info.fix.id);
-	else {
-		iounmap(fb_info.screen_base);
-		iounmap_macfb();
-	}
+	if (err)
+		goto fail_dealloc;
+
+	printk("fb%d: %s frame buffer device\n",
+	       fb_info.node, fb_info.fix.id);
+	return 0;
+
+fail_dealloc:
+	fb_dealloc_cmap(&fb_info.cmap);
+fail_unmap:
+	iounmap(fb_info.screen_base);
+	iounmap_macfb();
 	return err;
 }
 
diff --git a/drivers/video/mb862xx/mb862xxfb.c b/drivers/video/mb862xx/mb862xxfb.c
index 38718d9..fb64234 100644
--- a/drivers/video/mb862xx/mb862xxfb.c
+++ b/drivers/video/mb862xx/mb862xxfb.c
@@ -927,9 +927,9 @@ static int __devinit mb862xx_pci_probe(struct pci_dev *pdev,
 	}
 
 	dev_dbg(dev, "fb phys 0x%llx 0x%lx\n",
-		(u64)par->fb_base_phys, (ulong)par->mapped_vram);
+		(unsigned long long)par->fb_base_phys, (ulong)par->mapped_vram);
 	dev_dbg(dev, "mmio phys 0x%llx 0x%lx\n",
-		(u64)par->mmio_base_phys, (ulong)par->mmio_len);
+		(unsigned long long)par->mmio_base_phys, (ulong)par->mmio_len);
 
 	if (mb862xx_pci_gdc_init(par))
 		goto io_unmap;
diff --git a/drivers/video/omap/omapfb_main.c b/drivers/video/omap/omapfb_main.c
index 5a5e407..1a49519 100644
--- a/drivers/video/omap/omapfb_main.c
+++ b/drivers/video/omap/omapfb_main.c
@@ -392,7 +392,7 @@ static void set_fb_fix(struct fb_info *fbi)
 	int bpp;
 
 	rg = &plane->fbdev->mem_desc.region[plane->idx];
-	fbi->screen_base	= (char __iomem *)rg->vaddr;
+	fbi->screen_base	= rg->vaddr;
 	fix->smem_start		= rg->paddr;
 	fix->smem_len		= rg->size;
 
diff --git a/drivers/watchdog/hpwdt.c b/drivers/watchdog/hpwdt.c
index a3765e0b..763c1ea 100644
--- a/drivers/watchdog/hpwdt.c
+++ b/drivers/watchdog/hpwdt.c
@@ -40,6 +40,7 @@
 #include <linux/bootmem.h>
 #include <linux/slab.h>
 #include <asm/desc.h>
+#include <asm/cacheflush.h>
 
 #define PCI_BIOS32_SD_VALUE		0x5F32335F	/* "_32_" */
 #define CRU_BIOS_SIGNATURE_VALUE	0x55524324
@@ -394,6 +395,8 @@ static void __devinit dmi_find_cru(const struct dmi_header *dm)
 				smbios_cru64_ptr->double_offset;
 			cru_rom_addr = ioremap(cru_physical_address,
 				smbios_cru64_ptr->double_length);
+			set_memory_x((unsigned long)cru_rom_addr & PAGE_MASK,
+				smbios_cru64_ptr->double_length >> PAGE_SHIFT);
 		}
 	}
 }
@@ -482,7 +485,7 @@ static int hpwdt_pretimeout(struct notifier_block *nb, unsigned long ulReason,
 			"Management Log for details.\n");
 	}
 
-	return NOTIFY_STOP;
+	return NOTIFY_OK;
 }
 
 /*
diff --git a/drivers/watchdog/iTCO_vendor_support.c b/drivers/watchdog/iTCO_vendor_support.c
index ca344a85..2474ebc 100644
--- a/drivers/watchdog/iTCO_vendor_support.c
+++ b/drivers/watchdog/iTCO_vendor_support.c
@@ -1,7 +1,7 @@
 /*
  *	intel TCO vendor specific watchdog driver support
  *
- *	(c) Copyright 2006 Wim Van Sebroeck <wim@iguana.be>.
+ *	(c) Copyright 2006-2008 Wim Van Sebroeck <wim@iguana.be>.
  *
  *	This program is free software; you can redistribute it and/or
  *	modify it under the terms of the GNU General Public License
@@ -19,8 +19,7 @@
 
 /* Module and version information */
 #define DRV_NAME	"iTCO_vendor_support"
-#define DRV_VERSION	"1.01"
-#define DRV_RELDATE	"11-Nov-2006"
+#define DRV_VERSION	"1.02"
 #define PFX		DRV_NAME ": "
 
 /* Includes */
@@ -78,24 +77,6 @@ MODULE_PARM_DESC(vendorsupport, "iTCO vendor specific support mode, default=0 (n
  *	    20.6 seconds.
  */
 
-static void supermicro_old_pre_start(unsigned long acpibase)
-{
-	unsigned long val32;
-
-	val32 = inl(SMI_EN);
-	val32 &= 0xffffdfff;	/* Turn off SMI clearing watchdog */
-	outl(val32, SMI_EN);	/* Needed to activate watchdog */
-}
-
-static void supermicro_old_pre_stop(unsigned long acpibase)
-{
-	unsigned long val32;
-
-	val32 = inl(SMI_EN);
-	val32 &= 0x00002000;	/* Turn on SMI clearing watchdog */
-	outl(val32, SMI_EN);	/* Needed to deactivate watchdog */
-}
-
 static void supermicro_old_pre_keepalive(unsigned long acpibase)
 {
 	/* Reload TCO Timer (done in iTCO_wdt_keepalive) + */
@@ -247,18 +228,14 @@ static void supermicro_new_pre_set_heartbeat(unsigned int heartbeat)
 void iTCO_vendor_pre_start(unsigned long acpibase,
 			   unsigned int heartbeat)
 {
-	if (vendorsupport == SUPERMICRO_OLD_BOARD)
-		supermicro_old_pre_start(acpibase);
-	else if (vendorsupport == SUPERMICRO_NEW_BOARD)
+	if (vendorsupport == SUPERMICRO_NEW_BOARD)
 		supermicro_new_pre_start(heartbeat);
 }
 EXPORT_SYMBOL(iTCO_vendor_pre_start);
 
 void iTCO_vendor_pre_stop(unsigned long acpibase)
 {
-	if (vendorsupport == SUPERMICRO_OLD_BOARD)
-		supermicro_old_pre_stop(acpibase);
-	else if (vendorsupport == SUPERMICRO_NEW_BOARD)
+	if (vendorsupport == SUPERMICRO_NEW_BOARD)
 		supermicro_new_pre_stop();
 }
 EXPORT_SYMBOL(iTCO_vendor_pre_stop);
diff --git a/drivers/watchdog/iTCO_wdt.c b/drivers/watchdog/iTCO_wdt.c
index bfb93bc..5b395a4 100644
--- a/drivers/watchdog/iTCO_wdt.c
+++ b/drivers/watchdog/iTCO_wdt.c
@@ -1,7 +1,7 @@
 /*
  *	intel TCO Watchdog Driver (Used in i82801 and i6300ESB chipsets)
  *
- *	(c) Copyright 2006-2007 Wim Van Sebroeck <wim@iguana.be>.
+ *	(c) Copyright 2006-2008 Wim Van Sebroeck <wim@iguana.be>.
  *
  *	This program is free software; you can redistribute it and/or
  *	modify it under the terms of the GNU General Public License
@@ -20,34 +20,41 @@
  *	82801BAM (ICH2-M)    : document number 290687-002, 298242-027,
  *	82801CA  (ICH3-S)    : document number 290733-003, 290739-013,
  *	82801CAM (ICH3-M)    : document number 290716-001, 290718-007,
- *	82801DB  (ICH4)      : document number 290744-001, 290745-020,
- *	82801DBM (ICH4-M)    : document number 252337-001, 252663-005,
+ *	82801DB  (ICH4)      : document number 290744-001, 290745-025,
+ *	82801DBM (ICH4-M)    : document number 252337-001, 252663-008,
  *	82801E   (C-ICH)     : document number 273599-001, 273645-002,
- *	82801EB  (ICH5)      : document number 252516-001, 252517-003,
- *	82801ER  (ICH5R)     : document number 252516-001, 252517-003,
- *	82801FB  (ICH6)      : document number 301473-002, 301474-007,
- *	82801FR  (ICH6R)     : document number 301473-002, 301474-007,
- *	82801FBM (ICH6-M)    : document number 301473-002, 301474-007,
- *	82801FW  (ICH6W)     : document number 301473-001, 301474-007,
- *	82801FRW (ICH6RW)    : document number 301473-001, 301474-007,
- *	82801GB  (ICH7)      : document number 307013-002, 307014-009,
- *	82801GR  (ICH7R)     : document number 307013-002, 307014-009,
- *	82801GDH (ICH7DH)    : document number 307013-002, 307014-009,
- *	82801GBM (ICH7-M)    : document number 307013-002, 307014-009,
- *	82801GHM (ICH7-M DH) : document number 307013-002, 307014-009,
- *	82801HB  (ICH8)      : document number 313056-003, 313057-009,
- *	82801HR  (ICH8R)     : document number 313056-003, 313057-009,
- *	82801HBM (ICH8M)     : document number 313056-003, 313057-009,
- *	82801HH  (ICH8DH)    : document number 313056-003, 313057-009,
- *	82801HO  (ICH8DO)    : document number 313056-003, 313057-009,
- *	82801HEM (ICH8M-E)   : document number 313056-003, 313057-009,
- *	82801IB  (ICH9)      : document number 316972-001, 316973-006,
- *	82801IR  (ICH9R)     : document number 316972-001, 316973-006,
- *	82801IH  (ICH9DH)    : document number 316972-001, 316973-006,
- *	82801IO  (ICH9DO)    : document number 316972-001, 316973-006,
- *	6300ESB  (6300ESB)   : document number 300641-003, 300884-010,
- *	631xESB  (631xESB)   : document number 313082-001, 313075-005,
- *	632xESB  (632xESB)   : document number 313082-001, 313075-005
+ *	82801EB  (ICH5)      : document number 252516-001, 252517-028,
+ *	82801ER  (ICH5R)     : document number 252516-001, 252517-028,
+ *	6300ESB  (6300ESB)   : document number 300641-004, 300884-013,
+ *	82801FB  (ICH6)      : document number 301473-002, 301474-026,
+ *	82801FR  (ICH6R)     : document number 301473-002, 301474-026,
+ *	82801FBM (ICH6-M)    : document number 301473-002, 301474-026,
+ *	82801FW  (ICH6W)     : document number 301473-001, 301474-026,
+ *	82801FRW (ICH6RW)    : document number 301473-001, 301474-026,
+ *	631xESB  (631xESB)   : document number 313082-001, 313075-006,
+ *	632xESB  (632xESB)   : document number 313082-001, 313075-006,
+ *	82801GB  (ICH7)      : document number 307013-003, 307014-024,
+ *	82801GR  (ICH7R)     : document number 307013-003, 307014-024,
+ *	82801GDH (ICH7DH)    : document number 307013-003, 307014-024,
+ *	82801GBM (ICH7-M)    : document number 307013-003, 307014-024,
+ *	82801GHM (ICH7-M DH) : document number 307013-003, 307014-024,
+ *	82801GU  (ICH7-U)    : document number 307013-003, 307014-024,
+ *	82801HB  (ICH8)      : document number 313056-003, 313057-017,
+ *	82801HR  (ICH8R)     : document number 313056-003, 313057-017,
+ *	82801HBM (ICH8M)     : document number 313056-003, 313057-017,
+ *	82801HH  (ICH8DH)    : document number 313056-003, 313057-017,
+ *	82801HO  (ICH8DO)    : document number 313056-003, 313057-017,
+ *	82801HEM (ICH8M-E)   : document number 313056-003, 313057-017,
+ *	82801IB  (ICH9)      : document number 316972-004, 316973-012,
+ *	82801IR  (ICH9R)     : document number 316972-004, 316973-012,
+ *	82801IH  (ICH9DH)    : document number 316972-004, 316973-012,
+ *	82801IO  (ICH9DO)    : document number 316972-004, 316973-012,
+ *	82801IBM (ICH9M)     : document number 316972-004, 316973-012,
+ *	82801IEM (ICH9M-E)   : document number 316972-004, 316973-012,
+ *	82801JIB (ICH10)     : document number 319973-002, 319974-002,
+ *	82801JIR (ICH10R)    : document number 319973-002, 319974-002,
+ *	82801JD  (ICH10D)    : document number 319973-002, 319974-002,
+ *	82801JDO (ICH10DO)   : document number 319973-002, 319974-002
  */
 
 /*
@@ -56,8 +63,7 @@
 
 /* Module and version information */
 #define DRV_NAME	"iTCO_wdt"
-#define DRV_VERSION	"1.03"
-#define DRV_RELDATE	"30-Apr-2008"
+#define DRV_VERSION	"1.04"
 #define PFX		DRV_NAME ": "
 
 /* Includes */
@@ -96,19 +102,26 @@ enum iTCO_chipsets {
 	TCO_ICH6,	/* ICH6 & ICH6R */
 	TCO_ICH6M,	/* ICH6-M */
 	TCO_ICH6W,	/* ICH6W & ICH6RW */
+	TCO_631XESB,	/* 631xESB/632xESB */
 	TCO_ICH7,	/* ICH7 & ICH7R */
-	TCO_ICH7M,	/* ICH7-M */
+	TCO_ICH7DH,	/* ICH7DH */
+	TCO_ICH7M,	/* ICH7-M & ICH7-U */
 	TCO_ICH7MDH,	/* ICH7-M DH */
 	TCO_ICH8,	/* ICH8 & ICH8R */
-	TCO_ICH8ME,	/* ICH8M-E */
 	TCO_ICH8DH,	/* ICH8DH */
 	TCO_ICH8DO,	/* ICH8DO */
 	TCO_ICH8M,	/* ICH8M */
+	TCO_ICH8ME,	/* ICH8M-E */
 	TCO_ICH9,	/* ICH9 */
 	TCO_ICH9R,	/* ICH9R */
 	TCO_ICH9DH,	/* ICH9DH */
 	TCO_ICH9DO,	/* ICH9DO */
-	TCO_631XESB,	/* 631xESB/632xESB */
+	TCO_ICH9M,	/* ICH9M */
+	TCO_ICH9ME,	/* ICH9M-E */
+	TCO_ICH10,	/* ICH10 */
+	TCO_ICH10R,	/* ICH10R */
+	TCO_ICH10D,	/* ICH10D */
+	TCO_ICH10DO,	/* ICH10DO */
 };
 
 static struct {
@@ -129,19 +142,26 @@ static struct {
 	{"ICH6 or ICH6R", 2},
 	{"ICH6-M", 2},
 	{"ICH6W or ICH6RW", 2},
+	{"631xESB/632xESB", 2},
 	{"ICH7 or ICH7R", 2},
-	{"ICH7-M", 2},
+	{"ICH7DH", 2},
+	{"ICH7-M or ICH7-U", 2},
 	{"ICH7-M DH", 2},
 	{"ICH8 or ICH8R", 2},
-	{"ICH8M-E", 2},
 	{"ICH8DH", 2},
 	{"ICH8DO", 2},
 	{"ICH8M", 2},
+	{"ICH8M-E", 2},
 	{"ICH9", 2},
 	{"ICH9R", 2},
 	{"ICH9DH", 2},
 	{"ICH9DO", 2},
-	{"631xESB/632xESB", 2},
+	{"ICH9M", 2},
+	{"ICH9M-E", 2},
+	{"ICH10", 2},
+	{"ICH10R", 2},
+	{"ICH10D", 2},
+	{"ICH10DO", 2},
 	{NULL, 0}
 };
 
@@ -175,18 +195,6 @@ static struct pci_device_id iTCO_wdt_pci_tbl[] = {
 	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_0,		TCO_ICH6)},
 	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_1,		TCO_ICH6M)},
 	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_2,		TCO_ICH6W)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_0,		TCO_ICH7)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_1,		TCO_ICH7M)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_31,		TCO_ICH7MDH)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_0,		TCO_ICH8)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_1,		TCO_ICH8ME)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_2,		TCO_ICH8DH)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_3,		TCO_ICH8DO)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_4,		TCO_ICH8M)},
-	{ ITCO_PCI_DEVICE(0x2918,				TCO_ICH9)},
-	{ ITCO_PCI_DEVICE(0x2916,				TCO_ICH9R)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_2,		TCO_ICH9DH)},
-	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_4,		TCO_ICH9DO)},
 	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ESB2_0,		TCO_631XESB)},
 	{ ITCO_PCI_DEVICE(0x2671,				TCO_631XESB)},
 	{ ITCO_PCI_DEVICE(0x2672,				TCO_631XESB)},
@@ -203,6 +211,25 @@ static struct pci_device_id iTCO_wdt_pci_tbl[] = {
 	{ ITCO_PCI_DEVICE(0x267d,				TCO_631XESB)},
 	{ ITCO_PCI_DEVICE(0x267e,				TCO_631XESB)},
 	{ ITCO_PCI_DEVICE(0x267f,				TCO_631XESB)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_0,		TCO_ICH7)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_30,		TCO_ICH7DH)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_1,		TCO_ICH7M)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_31,		TCO_ICH7MDH)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_0,		TCO_ICH8)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_2,		TCO_ICH8DH)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_3,		TCO_ICH8DO)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_4,		TCO_ICH8M)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_1,		TCO_ICH8ME)},
+	{ ITCO_PCI_DEVICE(0x2918,				TCO_ICH9)},
+	{ ITCO_PCI_DEVICE(0x2916,				TCO_ICH9R)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_2,		TCO_ICH9DH)},
+	{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_4,		TCO_ICH9DO)},
+	{ ITCO_PCI_DEVICE(0x2919,				TCO_ICH9M)},
+	{ ITCO_PCI_DEVICE(0x2917,				TCO_ICH9ME)},
+	{ ITCO_PCI_DEVICE(0x3a18,				TCO_ICH10)},
+	{ ITCO_PCI_DEVICE(0x3a16,				TCO_ICH10R)},
+	{ ITCO_PCI_DEVICE(0x3a1a,				TCO_ICH10D)},
+	{ ITCO_PCI_DEVICE(0x3a14,				TCO_ICH10DO)},
 	{ 0, },			/* End of list */
 };
 MODULE_DEVICE_TABLE(pci, iTCO_wdt_pci_tbl);
@@ -311,6 +338,7 @@ static int iTCO_wdt_unset_NO_REBOOT_bit(void)
 static int iTCO_wdt_start(void)
 {
 	unsigned int val;
+	unsigned long val32;
 
 	spin_lock(&iTCO_wdt_private.io_lock);
 
@@ -323,6 +351,18 @@ static int iTCO_wdt_start(void)
 		return -EIO;
 	}
 
+	/* Bit 13: TCO_EN -> 0 = Disables TCO logic generating an SMI# */
+	val32 = inl(SMI_EN);
+	val32 &= 0xffffdfff;	/* Turn off SMI clearing watchdog */
+	outl(val32, SMI_EN);
+
+	/* Force the timer to its reload value by writing to the TCO_RLD
+	   register */
+	if (iTCO_wdt_private.iTCO_version == 2)
+		outw(0x01, TCO_RLD);
+	else if (iTCO_wdt_private.iTCO_version == 1)
+		outb(0x01, TCO_RLD);
+
 	/* Bit 11: TCO Timer Halt -> 0 = The TCO timer is enabled to count */
 	val = inw(TCO1_CNT);
 	val &= 0xf7ff;
@@ -338,6 +378,7 @@ static int iTCO_wdt_start(void)
 static int iTCO_wdt_stop(void)
 {
 	unsigned int val;
+	unsigned long val32;
 
 	spin_lock(&iTCO_wdt_private.io_lock);
 
@@ -349,6 +390,11 @@ static int iTCO_wdt_stop(void)
 	outw(val, TCO1_CNT);
 	val = inw(TCO1_CNT);
 
+	/* Bit 13: TCO_EN -> 1 = Enables the TCO logic to generate SMI# */
+	val32 = inl(SMI_EN);
+	val32 |= 0x00002000;
+	outl(val32, SMI_EN);
+
 	/* Set the NO_REBOOT bit to prevent later reboots, just for sure */
 	iTCO_wdt_set_NO_REBOOT_bit();
 
@@ -459,7 +505,6 @@ static int iTCO_wdt_open(struct inode *inode, struct file *file)
 	/*
 	 *      Reload and activate timer
 	 */
-	iTCO_wdt_keepalive();
 	iTCO_wdt_start();
 	return nonseekable_open(inode, file);
 }
@@ -604,7 +649,6 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 	int ret;
 	u32 base_address;
 	unsigned long RCBA;
-	unsigned long val32;
 
 	/*
 	 *      Find the ACPI/PM base I/O address which is the base
@@ -644,17 +688,13 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 	/* Set the NO_REBOOT bit to prevent later reboots, just for sure */
 	iTCO_wdt_set_NO_REBOOT_bit();
 
-	/* Set the TCO_EN bit in SMI_EN register */
+	/* The TCO logic uses the TCO_EN bit in the SMI_EN register */
 	if (!request_region(SMI_EN, 4, "iTCO_wdt")) {
 		printk(KERN_ERR PFX
 			"I/O address 0x%04lx already in use\n", SMI_EN);
 		ret = -EIO;
 		goto out;
 	}
-	val32 = inl(SMI_EN);
-	val32 &= 0xffffdfff;	/* Turn off SMI clearing watchdog */
-	outl(val32, SMI_EN);
-	release_region(SMI_EN, 4);
 
 	/* The TCO I/O registers reside in a 32-byte range pointed to
 	   by the TCOBASE value */
@@ -662,7 +702,7 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 		printk(KERN_ERR PFX "I/O address 0x%04lx already in use\n",
 			TCOBASE);
 		ret = -EIO;
-		goto out;
+		goto unreg_smi_en;
 	}
 
 	printk(KERN_INFO PFX
@@ -672,8 +712,9 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 			TCOBASE);
 
 	/* Clear out the (probably old) status */
-	outb(0, TCO1_STS);
-	outb(3, TCO2_STS);
+	outb(8, TCO1_STS);	/* Clear the Time Out Status bit */
+	outb(2, TCO2_STS);	/* Clear SECOND_TO_STS bit */
+	outb(4, TCO2_STS);	/* Clear BOOT_STS bit */
 
 	/* Make sure the watchdog is not running */
 	iTCO_wdt_stop();
@@ -701,6 +742,8 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 
 unreg_region:
 	release_region(TCOBASE, 0x20);
+unreg_smi_en:
+	release_region(SMI_EN, 4);
 out:
 	if (iTCO_wdt_private.iTCO_version == 2)
 		iounmap(iTCO_wdt_private.gcs);
@@ -718,6 +761,7 @@ static void __devexit iTCO_wdt_cleanup(void)
 	/* Deregister */
 	misc_deregister(&iTCO_wdt_miscdev);
 	release_region(TCOBASE, 0x20);
+	release_region(SMI_EN, 4);
 	if (iTCO_wdt_private.iTCO_version == 2)
 		iounmap(iTCO_wdt_private.gcs);
 	pci_dev_put(iTCO_wdt_private.pdev);
@@ -782,8 +826,8 @@ static int __init iTCO_wdt_init_module(void)
 {
 	int err;
 
-	printk(KERN_INFO PFX "Intel TCO WatchDog Timer Driver v%s (%s)\n",
-		DRV_VERSION, DRV_RELDATE);
+	printk(KERN_INFO PFX "Intel TCO WatchDog Timer Driver v%s\n",
+		DRV_VERSION);
 
 	err = platform_driver_register(&iTCO_wdt_driver);
 	if (err)
diff --git a/drivers/watchdog/mtx-1_wdt.c b/drivers/watchdog/mtx-1_wdt.c
index b4b7b0a..3acce62 100644
--- a/drivers/watchdog/mtx-1_wdt.c
+++ b/drivers/watchdog/mtx-1_wdt.c
@@ -98,6 +98,8 @@ static void mtx1_wdt_reset(void)
 
 static void mtx1_wdt_start(void)
 {
+	unsigned long flags;
+
 	spin_lock_irqsave(&mtx1_wdt_device.lock, flags);
 	if (!mtx1_wdt_device.queue) {
 		mtx1_wdt_device.queue = 1;
@@ -110,6 +112,8 @@ static void mtx1_wdt_start(void)
 
 static int mtx1_wdt_stop(void)
 {
+	unsigned long flags;
+
 	spin_lock_irqsave(&mtx1_wdt_device.lock, flags);
 	if (mtx1_wdt_device.queue) {
 		mtx1_wdt_device.queue = 0;