summaryrefslogtreecommitdiffstats
path: root/drivers
diff options
context:
space:
mode:
authorMyungJoo Ham <myungjoo.ham@samsung.com>2010-08-20 14:43:56 +0900
committerLiam Girdwood <lrg@slimlogic.co.uk>2010-10-28 22:40:31 +0100
commit202f4f53e503ae09b431459131b5b3a99fa6d839 (patch)
tree71f4597427f8bc9011aca93f873bd01154f2d25d /drivers
parent2d3b07c07b39c4b7d9b6641052a02d996cd5d87c (diff)
downloadop-kernel-dev-202f4f53e503ae09b431459131b5b3a99fa6d839.zip
op-kernel-dev-202f4f53e503ae09b431459131b5b3a99fa6d839.tar.gz
MAX8952 PMIC Driver Initial Release
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV with DVS support. In this initial release, users can set voltages for four DVS modes, RAMP delay values, and SYNC frequency. Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID is not supported in this release. If GPIO of EN is not valid in platform data, the driver assumes that it is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down VID0 and VID1 to fix DVS mode as 0 and disables DVS support. We assume that V_OUT is capable to provide every voltage from 770mV to 1.40V in 10mV steps although the data sheet has some ambiguity on it. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> -- v2: - Style correction - Can accept platform_data with invalid GPIOs - Removed unnecessary features - Improved error handling Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Diffstat (limited to 'drivers')
-rw-r--r--drivers/regulator/Kconfig8
-rw-r--r--drivers/regulator/Makefile1
-rw-r--r--drivers/regulator/max8952.c360
3 files changed, 369 insertions, 0 deletions
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 172951b..4889caa 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -100,6 +100,14 @@ config REGULATOR_MAX8925
help
Say y here to support the voltage regulaltor of Maxim MAX8925 PMIC.
+config REGULATOR_MAX8952
+ tristate "Maxim MAX8952 Power Management IC"
+ depends on I2C
+ help
+ This driver controls a Maxim 8952 voltage output regulator
+ via I2C bus. Maxim 8952 has one voltage output and supports 4 DVS
+ modes ranging from 0.77V to 1.40V by 0.01V steps.
+
config REGULATOR_MAX8998
tristate "Maxim 8998 voltage regulator"
depends on MFD_MAX8998
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 8285fd8..beff6da 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o
obj-$(CONFIG_REGULATOR_MAX8649) += max8649.o
obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
obj-$(CONFIG_REGULATOR_MAX8925) += max8925-regulator.o
+obj-$(CONFIG_REGULATOR_MAX8952) += max8952.o
obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o
diff --git a/drivers/regulator/max8952.c b/drivers/regulator/max8952.c
new file mode 100644
index 0000000..f2af0b1
--- /dev/null
+++ b/drivers/regulator/max8952.c
@@ -0,0 +1,360 @@
+/*
+ * max8952.c - Voltage and current regulation for the Maxim 8952
+ *
+ * Copyright (C) 2010 Samsung Electronics
+ * MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/max8952.h>
+#include <linux/mutex.h>
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+
+/* Registers */
+enum {
+ MAX8952_REG_MODE0,
+ MAX8952_REG_MODE1,
+ MAX8952_REG_MODE2,
+ MAX8952_REG_MODE3,
+ MAX8952_REG_CONTROL,
+ MAX8952_REG_SYNC,
+ MAX8952_REG_RAMP,
+ MAX8952_REG_CHIP_ID1,
+ MAX8952_REG_CHIP_ID2,
+};
+
+struct max8952_data {
+ struct i2c_client *client;
+ struct device *dev;
+ struct mutex mutex;
+ struct max8952_platform_data *pdata;
+ struct regulator_dev *rdev;
+
+ bool vid0;
+ bool vid1;
+ bool en;
+};
+
+static int max8952_read_reg(struct max8952_data *max8952, u8 reg)
+{
+ int ret = i2c_smbus_read_byte_data(max8952->client, reg);
+ if (ret > 0)
+ ret &= 0xff;
+
+ return ret;
+}
+
+static int max8952_write_reg(struct max8952_data *max8952,
+ u8 reg, u8 value)
+{
+ return i2c_smbus_write_byte_data(max8952->client, reg, value);
+}
+
+static int max8952_voltage(struct max8952_data *max8952, u8 mode)
+{
+ return (max8952->pdata->dvs_mode[mode] * 10 + 770) * 1000;
+}
+
+static int max8952_list_voltage(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+
+ if (rdev_get_id(rdev) != 0)
+ return -EINVAL;
+
+ return max8952_voltage(max8952, selector);
+}
+
+static int max8952_is_enabled(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+ return max8952->en;
+}
+
+static int max8952_enable(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+
+ /* If not valid, assume "ALWAYS_HIGH" */
+ if (gpio_is_valid(max8952->pdata->gpio_en))
+ gpio_set_value(max8952->pdata->gpio_en, 1);
+
+ max8952->en = true;
+ return 0;
+}
+
+static int max8952_disable(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+
+ /* If not valid, assume "ALWAYS_HIGH" -> not permitted */
+ if (gpio_is_valid(max8952->pdata->gpio_en))
+ gpio_set_value(max8952->pdata->gpio_en, 0);
+ else
+ return -EPERM;
+
+ max8952->en = false;
+ return 0;
+}
+
+static int max8952_get_voltage(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+ u8 vid = 0;
+
+ if (max8952->vid0)
+ vid += 1;
+ if (max8952->vid1)
+ vid += 2;
+
+ return max8952_voltage(max8952, vid);
+}
+
+static int max8952_set_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+ u8 vid = -1, i;
+
+ if (!gpio_is_valid(max8952->pdata->gpio_vid0) ||
+ !gpio_is_valid(max8952->pdata->gpio_vid0)) {
+ /* DVS not supported */
+ return -EPERM;
+ }
+
+ for (i = 0; i < MAX8952_NUM_DVS_MODE; i++) {
+ int volt = max8952_voltage(max8952, i);
+
+ /* Set the voltage as low as possible within the range */
+ if (volt <= max_uV && volt >= min_uV)
+ if (vid == -1 || max8952_voltage(max8952, vid) > volt)
+ vid = i;
+ }
+
+ if (vid >= 0 && vid < MAX8952_NUM_DVS_MODE) {
+ max8952->vid0 = (vid % 2 == 1);
+ max8952->vid1 = (((vid >> 1) % 2) == 1);
+ gpio_set_value(max8952->pdata->gpio_vid0, max8952->vid0);
+ gpio_set_value(max8952->pdata->gpio_vid1, max8952->vid1);
+ } else
+ return -EINVAL;
+
+ return 0;
+}
+
+static struct regulator_ops max8952_ops = {
+ .list_voltage = max8952_list_voltage,
+ .is_enabled = max8952_is_enabled,
+ .enable = max8952_enable,
+ .disable = max8952_disable,
+ .get_voltage = max8952_get_voltage,
+ .set_voltage = max8952_set_voltage,
+ .set_suspend_disable = max8952_disable,
+};
+
+static struct regulator_desc regulator = {
+ .name = "MAX8952_VOUT",
+ .id = 0,
+ .n_voltages = MAX8952_NUM_DVS_MODE,
+ .ops = &max8952_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+};
+
+static int __devinit max8952_pmic_probe(struct i2c_client *client,
+ const struct i2c_device_id *i2c_id)
+{
+ struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+ struct max8952_platform_data *pdata = client->dev.platform_data;
+ struct max8952_data *max8952;
+
+ int ret = 0, err = 0;
+
+ if (!pdata) {
+ dev_err(&client->dev, "Require the platform data\n");
+ return -EINVAL;
+ }
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
+ return -EIO;
+
+ max8952 = kzalloc(sizeof(struct max8952_data), GFP_KERNEL);
+ if (!max8952)
+ return -ENOMEM;
+
+ max8952->client = client;
+ max8952->dev = &client->dev;
+ max8952->pdata = pdata;
+ mutex_init(&max8952->mutex);
+
+ max8952->rdev = regulator_register(&regulator, max8952->dev,
+ &pdata->reg_data, max8952);
+
+ ret = IS_ERR(max8952->rdev);
+ if (ret)
+ dev_err(max8952->dev, "regulator init failed (%d)\n", ret);
+
+ max8952->en = !!(pdata->reg_data.constraints.boot_on);
+ max8952->vid0 = (pdata->default_mode % 2) == 1;
+ max8952->vid1 = ((pdata->default_mode >> 1) % 2) == 1;
+
+ if (gpio_is_valid(pdata->gpio_en)) {
+ if (!gpio_request(pdata->gpio_en, "MAX8952 EN"))
+ gpio_direction_output(pdata->gpio_en, max8952->en);
+ else
+ err = 1;
+ } else
+ err = 2;
+
+ if (err) {
+ dev_info(max8952->dev, "EN gpio invalid: assume that EN"
+ "is always High\n");
+ max8952->en = 1;
+ pdata->gpio_en = -1; /* Mark invalid */
+ }
+
+ err = 0;
+
+ if (gpio_is_valid(pdata->gpio_vid0) &&
+ gpio_is_valid(pdata->gpio_vid1)) {
+ if (!gpio_request(pdata->gpio_vid0, "MAX8952 VID0"))
+ gpio_direction_output(pdata->gpio_vid0,
+ (pdata->default_mode) % 2);
+ else
+ err = 1;
+
+ if (!gpio_request(pdata->gpio_vid1, "MAX8952 VID1"))
+ gpio_direction_output(pdata->gpio_vid1,
+ (pdata->default_mode >> 1) % 2);
+ else {
+ if (!err)
+ gpio_free(pdata->gpio_vid0);
+ err = 2;
+ }
+
+ } else
+ err = 3;
+
+ if (err) {
+ dev_warn(max8952->dev, "VID0/1 gpio invalid: "
+ "DVS not avilable.\n");
+ max8952->vid0 = 0;
+ max8952->vid1 = 0;
+ /* Mark invalid */
+ pdata->gpio_vid0 = -1;
+ pdata->gpio_vid1 = -1;
+
+ /* Disable Pulldown of EN only */
+ max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x60);
+
+ dev_err(max8952->dev, "DVS modes disabled because VID0 and VID1"
+ " do not have proper controls.\n");
+ } else {
+ /*
+ * Disable Pulldown on EN, VID0, VID1 to reduce
+ * leakage current of MAX8952 assuming that MAX8952
+ * is turned on (EN==1). Note that without having VID0/1
+ * properly connected, turning pulldown off can be
+ * problematic. Thus, turn this off only when they are
+ * controllable by GPIO.
+ */
+ max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x0);
+ }
+
+ max8952_write_reg(max8952, MAX8952_REG_MODE0,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE0) & 0xC0) |
+ (pdata->dvs_mode[0] & 0x3F));
+ max8952_write_reg(max8952, MAX8952_REG_MODE1,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE1) & 0xC0) |
+ (pdata->dvs_mode[1] & 0x3F));
+ max8952_write_reg(max8952, MAX8952_REG_MODE2,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE2) & 0xC0) |
+ (pdata->dvs_mode[2] & 0x3F));
+ max8952_write_reg(max8952, MAX8952_REG_MODE3,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE3) & 0xC0) |
+ (pdata->dvs_mode[3] & 0x3F));
+
+ max8952_write_reg(max8952, MAX8952_REG_SYNC,
+ (max8952_read_reg(max8952, MAX8952_REG_SYNC) & 0x3F) |
+ ((pdata->sync_freq & 0x3) << 6));
+ max8952_write_reg(max8952, MAX8952_REG_RAMP,
+ (max8952_read_reg(max8952, MAX8952_REG_RAMP) & 0x1F) |
+ ((pdata->ramp_speed & 0x7) << 5));
+
+ i2c_set_clientdata(client, max8952);
+
+ return ret;
+}
+
+static int __devexit max8952_pmic_remove(struct i2c_client *client)
+{
+ struct max8952_data *max8952 = i2c_get_clientdata(client);
+ struct max8952_platform_data *pdata = max8952->pdata;
+ struct regulator_dev *rdev = max8952->rdev;
+
+ regulator_unregister(rdev);
+
+ gpio_free(pdata->gpio_vid0);
+ gpio_free(pdata->gpio_vid1);
+ gpio_free(pdata->gpio_en);
+
+ kfree(max8952);
+ return 0;
+}
+
+static const struct i2c_device_id max8952_ids[] = {
+ { "max8952", 0 },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, max8952_ids);
+
+static struct i2c_driver max8952_pmic_driver = {
+ .probe = max8952_pmic_probe,
+ .remove = __devexit_p(max8952_pmic_remove),
+ .driver = {
+ .name = "max8952",
+ },
+ .id_table = max8952_ids,
+};
+
+static int __init max8952_pmic_init(void)
+{
+ return i2c_add_driver(&max8952_pmic_driver);
+}
+subsys_initcall(max8952_pmic_init);
+
+static void __exit max8952_pmic_exit(void)
+{
+ i2c_del_driver(&max8952_pmic_driver);
+}
+module_exit(max8952_pmic_exit);
+
+MODULE_DESCRIPTION("MAXIM 8952 voltage regulator driver");
+MODULE_AUTHOR("MyungJoo Ham <myungjoo.ham@samsung.com>");
+MODULE_LICENSE("GPL");
OpenPOWER on IntegriCloud