summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/xhci-pci.c
diff options
context:
space:
mode:
authorSarah Sharp <sarah.a.sharp@linux.intel.com>2011-05-11 16:14:58 -0700
committerSarah Sharp <sarah.a.sharp@linux.intel.com>2011-05-27 12:08:14 -0700
commit2cf95c18d5069e13c02a8667d91e064df8e17e09 (patch)
tree05ae0e90ceab6790ccd1e624b695b984c6081f87 /drivers/usb/host/xhci-pci.c
parentad808333d8201d53075a11bc8dd83b81f3d68f0b (diff)
downloadop-kernel-dev-2cf95c18d5069e13c02a8667d91e064df8e17e09.zip
op-kernel-dev-2cf95c18d5069e13c02a8667d91e064df8e17e09.tar.gz
Intel xhci: Limit number of active endpoints to 64.
The Panther Point chipset has an xHCI host controller that has a limit to the number of active endpoints it can handle. Ideally, it would signal that it can't handle anymore endpoints by returning a Resource Error for the Configure Endpoint command, but they don't. Instead it needs software to keep track of the number of active endpoints, across configure endpoint commands, reset device commands, disable slot commands, and address device commands. Add a new endpoint context counter, xhci_hcd->num_active_eps, and use it to track the number of endpoints the xHC has active. This gets a little tricky, because commands to change the number of active endpoints can fail. This patch adds a new xHCI quirk for these Intel hosts, and the new code should not have any effect on other xHCI host controllers. Fail a new device allocation if we don't have room for the new default control endpoint. Use the endpoint ring pointers to determine what endpoints were active before a Reset Device command or a Disable Slot command, and drop those once the command completes. Fail a configure endpoint command if it would add too many new endpoints. We have to be a bit over zealous here, and only count the number of new endpoints to be added, without subtracting the number of dropped endpoints. That's because a second configure endpoint command for a different device could sneak in before we know if the first command is completed. If the first command dropped resources, the host controller fails the command for some reason, and we're nearing the limit of endpoints, we could end up oversubscribing the host. To fix this race condition, when evaluating whether a configure endpoint command will fix in our bandwidth budget, only add the new endpoints to xhci->num_active_eps, and don't subtract the dropped endpoints. Ignore changed endpoints (ones that are dropped and then re-added), as that shouldn't effect the host's endpoint resources. When the configure endpoint command completes, subtract off the dropped endpoints. This may mean some configuration changes may temporarily fail, but it's always better to under-subscribe than over-subscribe resources. (Originally my plan had been to push the resource allocation down into the ring allocation functions. However, that would cause us to allocate unnecessary resources when endpoints were changed, because the xHCI driver allocates a new ring for the changed endpoint, and only deletes the old ring once the Configure Endpoint command succeeds. A further complication would have been dealing with the per-device endpoint ring cache.) Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Diffstat (limited to 'drivers/usb/host/xhci-pci.c')
-rw-r--r--drivers/usb/host/xhci-pci.c2
1 files changed, 2 insertions, 0 deletions
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index eafd17f..c408e9f 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -121,6 +121,8 @@ static int xhci_pci_setup(struct usb_hcd *hcd)
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) {
xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
+ xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
+ xhci->limit_active_eps = 64;
}
/* Make sure the HC is halted. */
OpenPOWER on IntegriCloud