ARM: OMAP: USB: Change omap USB code to use omap_read/write instead of __REG

Change omap USB code to use omap_read/write instead of __REG for multi-omap

Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 30 insertions, 31 deletions

diff --git a/drivers/usb/gadget/omap_udc.h b/drivers/usb/gadget/omap_udc.h
index c6b9cbc..8522bbb 100644
--- a/drivers/usb/gadget/omap_udc.h
+++ b/drivers/usb/gadget/omap_udc.h
@@ -8,23 +8,22 @@
 /*
  * USB device/endpoint management registers
  */
-#define UDC_REG(offset)              __REG16(UDC_BASE + (offset))
 
-#define	UDC_REV_REG			UDC_REG(0x0)	/* Revision */
-#define	UDC_EP_NUM_REG			UDC_REG(0x4)	/* Which endpoint */
+#define	UDC_REV				(UDC_BASE + 0x0)	/* Revision */
+#define	UDC_EP_NUM			(UDC_BASE + 0x4)	/* Which endpoint */
 #	define	UDC_SETUP_SEL		(1 << 6)
 #	define	UDC_EP_SEL		(1 << 5)
 #	define	UDC_EP_DIR		(1 << 4)
 	/* low 4 bits for endpoint number */
-#define	UDC_DATA_REG			UDC_REG(0x08)	/* Endpoint FIFO */
-#define	UDC_CTRL_REG			UDC_REG(0x0C)	/* Endpoint control */
+#define	UDC_DATA			(UDC_BASE + 0x08)	/* Endpoint FIFO */
+#define	UDC_CTRL			(UDC_BASE + 0x0C)	/* Endpoint control */
 #	define	UDC_CLR_HALT		(1 << 7)
 #	define	UDC_SET_HALT		(1 << 6)
 #	define	UDC_CLRDATA_TOGGLE	(1 << 3)
 #	define	UDC_SET_FIFO_EN		(1 << 2)
 #	define	UDC_CLR_EP		(1 << 1)
 #	define	UDC_RESET_EP		(1 << 0)
-#define	UDC_STAT_FLG_REG		UDC_REG(0x10)	/* Endpoint status */
+#define	UDC_STAT_FLG			(UDC_BASE + 0x10)	/* Endpoint status */
 #	define	UDC_NO_RXPACKET		(1 << 15)
 #	define	UDC_MISS_IN		(1 << 14)
 #	define	UDC_DATA_FLUSH		(1 << 13)
@@ -38,8 +37,8 @@
 #	define	UDC_FIFO_EN		(1 << 2)
 #	define	UDC_NON_ISO_FIFO_EMPTY	(1 << 1)
 #	define	UDC_NON_ISO_FIFO_FULL	(1 << 0)
-#define	UDC_RXFSTAT_REG			UDC_REG(0x14)	/* OUT bytecount */
-#define	UDC_SYSCON1_REG			UDC_REG(0x18)	/* System config 1 */
+#define	UDC_RXFSTAT			(UDC_BASE + 0x14)	/* OUT bytecount */
+#define	UDC_SYSCON1			(UDC_BASE + 0x18)	/* System config 1 */
 #	define	UDC_CFG_LOCK		(1 << 8)
 #	define	UDC_DATA_ENDIAN		(1 << 7)
 #	define	UDC_DMA_ENDIAN		(1 << 6)
@@ -48,12 +47,12 @@
 #	define	UDC_SELF_PWR		(1 << 2)
 #	define	UDC_SOFF_DIS		(1 << 1)
 #	define	UDC_PULLUP_EN		(1 << 0)
-#define	UDC_SYSCON2_REG			UDC_REG(0x1C)	/* System config 2 */
+#define	UDC_SYSCON2			(UDC_BASE + 0x1C)	/* System config 2 */
 #	define	UDC_RMT_WKP		(1 << 6)
 #	define	UDC_STALL_CMD		(1 << 5)
 #	define	UDC_DEV_CFG		(1 << 3)
 #	define	UDC_CLR_CFG		(1 << 2)
-#define	UDC_DEVSTAT_REG			UDC_REG(0x20)	/* Device status */
+#define	UDC_DEVSTAT			(UDC_BASE + 0x20)	/* Device status */
 #	define	UDC_B_HNP_ENABLE	(1 << 9)
 #	define	UDC_A_HNP_SUPPORT	(1 << 8)
 #	define	UDC_A_ALT_HNP_SUPPORT	(1 << 7)
@@ -64,26 +63,26 @@
 #	define	UDC_ADD			(1 << 2)
 #	define	UDC_DEF			(1 << 1)
 #	define	UDC_ATT			(1 << 0)
-#define	UDC_SOF_REG			UDC_REG(0x24)	/* Start of frame */
+#define	UDC_SOF				(UDC_BASE + 0x24)	/* Start of frame */
 #	define	UDC_FT_LOCK		(1 << 12)
 #	define	UDC_TS_OK		(1 << 11)
 #	define	UDC_TS			0x03ff
-#define	UDC_IRQ_EN_REG			UDC_REG(0x28)	/* Interrupt enable */
+#define	UDC_IRQ_EN			(UDC_BASE + 0x28)	/* Interrupt enable */
 #	define	UDC_SOF_IE		(1 << 7)
 #	define	UDC_EPN_RX_IE		(1 << 5)
 #	define	UDC_EPN_TX_IE		(1 << 4)
 #	define	UDC_DS_CHG_IE		(1 << 3)
 #	define	UDC_EP0_IE		(1 << 0)
-#define	UDC_DMA_IRQ_EN_REG		UDC_REG(0x2C)	/* DMA irq enable */
+#define	UDC_DMA_IRQ_EN			(UDC_BASE + 0x2C)	/* DMA irq enable */
 	/* rx/tx dma channels numbered 1-3 not 0-2 */
 #	define	UDC_TX_DONE_IE(n)	(1 << (4 * (n) - 2))
 #	define	UDC_RX_CNT_IE(n)	(1 << (4 * (n) - 3))
 #	define	UDC_RX_EOT_IE(n)	(1 << (4 * (n) - 4))
-#define	UDC_IRQ_SRC_REG			UDC_REG(0x30)	/* Interrupt source */
+#define	UDC_IRQ_SRC			(UDC_BASE + 0x30)	/* Interrupt source */
 #	define	UDC_TXN_DONE		(1 << 10)
 #	define	UDC_RXN_CNT		(1 << 9)
 #	define	UDC_RXN_EOT		(1 << 8)
-#	define	UDC_SOF			(1 << 7)
+#	define	UDC_IRQ_SOF		(1 << 7)
 #	define	UDC_EPN_RX		(1 << 5)
 #	define	UDC_EPN_TX		(1 << 4)
 #	define	UDC_DS_CHG		(1 << 3)
@@ -91,41 +90,41 @@
 #	define	UDC_EP0_RX		(1 << 1)
 #	define	UDC_EP0_TX		(1 << 0)
 #	define	UDC_IRQ_SRC_MASK	0x7bf
-#define	UDC_EPN_STAT_REG		UDC_REG(0x34)	/* EP irq status */
-#define	UDC_DMAN_STAT_REG		UDC_REG(0x38)	/* DMA irq status */
+#define	UDC_EPN_STAT			(UDC_BASE + 0x34)	/* EP irq status */
+#define	UDC_DMAN_STAT			(UDC_BASE + 0x38)	/* DMA irq status */
 #	define	UDC_DMA_RX_SB		(1 << 12)
 #	define	UDC_DMA_RX_SRC(x)	(((x)>>8) & 0xf)
 #	define	UDC_DMA_TX_SRC(x)	(((x)>>0) & 0xf)
 
 
 /* DMA configuration registers:  up to three channels in each direction.  */
-#define	UDC_RXDMA_CFG_REG		UDC_REG(0x40)	/* 3 eps for RX DMA */
+#define	UDC_RXDMA_CFG			(UDC_BASE + 0x40)	/* 3 eps for RX DMA */
 #	define	UDC_DMA_REQ		(1 << 12)
-#define	UDC_TXDMA_CFG_REG		UDC_REG(0x44)	/* 3 eps for TX DMA */
-#define	UDC_DATA_DMA_REG		UDC_REG(0x48)	/* rx/tx fifo addr */
+#define	UDC_TXDMA_CFG			(UDC_BASE + 0x44)	/* 3 eps for TX DMA */
+#define	UDC_DATA_DMA			(UDC_BASE + 0x48)	/* rx/tx fifo addr */
 
 /* rx/tx dma control, numbering channels 1-3 not 0-2 */
-#define	UDC_TXDMA_REG(chan)		UDC_REG(0x50 - 4 + 4 * (chan))
+#define	UDC_TXDMA(chan)			(UDC_BASE + 0x50 - 4 + 4 * (chan))
 #	define UDC_TXN_EOT		(1 << 15)	/* bytes vs packets */
 #	define UDC_TXN_START		(1 << 14)	/* start transfer */
 #	define UDC_TXN_TSC		0x03ff		/* units in xfer */
-#define	UDC_RXDMA_REG(chan)		UDC_REG(0x60 - 4 + 4 * (chan))
+#define	UDC_RXDMA(chan)			(UDC_BASE + 0x60 - 4 + 4 * (chan))
 #	define UDC_RXN_STOP		(1 << 15)	/* enable EOT irq */
 #	define UDC_RXN_TC		0x00ff		/* packets in xfer */
 
 
 /*
  * Endpoint configuration registers (used before CFG_LOCK is set)
- * UDC_EP_TX_REG(0) is unused
+ * UDC_EP_TX(0) is unused
  */
-#define	UDC_EP_RX_REG(endpoint)		UDC_REG(0x80 + (endpoint)*4)
+#define	UDC_EP_RX(endpoint)		(UDC_BASE + 0x80 + (endpoint)*4)
 #	define	UDC_EPN_RX_VALID	(1 << 15)
 #	define	UDC_EPN_RX_DB		(1 << 14)
 	/* buffer size in bits 13, 12 */
 #	define	UDC_EPN_RX_ISO		(1 << 11)
 	/* buffer pointer in low 11 bits */
-#define	UDC_EP_TX_REG(endpoint)		UDC_REG(0xc0 + (endpoint)*4)
-	/* same bitfields as in RX_REG */
+#define	UDC_EP_TX(endpoint)		(UDC_BASE + 0xc0 + (endpoint)*4)
+	/* same bitfields as in RX */
 
 /*-------------------------------------------------------------------------*/
 
@@ -195,14 +194,14 @@ struct omap_udc {
 
 /*-------------------------------------------------------------------------*/
 
-#define	MOD_CONF_CTRL_0_REG	__REG32(MOD_CONF_CTRL_0)
-#define	VBUS_W2FC_1510		(1 << 17)	/* 0 gpio0, 1 dvdd2 pin */
+/* MOD_CONF_CTRL_0 */
+#define VBUS_W2FC_1510		(1 << 17)	/* 0 gpio0, 1 dvdd2 pin */
 
-#define	FUNC_MUX_CTRL_0_REG	__REG32(FUNC_MUX_CTRL_0)
+/* FUNC_MUX_CTRL_0 */
 #define	VBUS_CTRL_1510		(1 << 19)	/* 1 connected (software) */
 #define	VBUS_MODE_1510		(1 << 18)	/* 0 hardware, 1 software */
 
-#define	HMC_1510	((MOD_CONF_CTRL_0_REG >> 1) & 0x3f)
-#define	HMC_1610	(OTG_SYSCON_2_REG & 0x3f)
+#define	HMC_1510	((omap_readl(MOD_CONF_CTRL_0) >> 1) & 0x3f)
+#define	HMC_1610	(omap_readl(OTG_SYSCON_2) & 0x3f)
 #define	HMC		(cpu_is_omap15xx() ? HMC_1510 : HMC_1610)