summaryrefslogtreecommitdiffstats
path: root/drivers/tty
diff options
context:
space:
mode:
authorSiftar, Gabe <Gabe.Siftar@getingeusa.com>2012-03-29 15:40:05 +0200
committerGreg Kroah-Hartman <gregkh@linuxfoundation.org>2012-04-09 10:30:39 -0700
commit57c3686842114de3b0c00633591e9605c46fb769 (patch)
treec90d5dda0cf538951e3598cc4b9cbe160d0f440e /drivers/tty
parentacede70d6561f2d042d9dbb153d9a3469479c0ed (diff)
downloadop-kernel-dev-57c3686842114de3b0c00633591e9605c46fb769.zip
op-kernel-dev-57c3686842114de3b0c00633591e9605c46fb769.tar.gz
tty/serial: atmel_serial: fix RS485 half-duplex problem
On our custom board, we are using RS485 in half-duplex mode on an AT91SAM9G45. SER_RS485_RX_DURING_TX is not set as we do not want to receive the data we transmit (our transceiver will receive transmitted data). Although the current driver attempts to disable and enable the receiver at the appropriate points, incoming data is still loaded into the receive register causing our code to receive the very last byte that was sent once the receiver is enabled. I ran this by Atmel support and they wrote: "The issue comes from the fact that you disable the PDC/DMA Reception and not the USART Reception channel. In your case, the[n] you will still receive data into the USART_RHR register, and maybe you [h]ave the overrun flag set. So please disable the USART reception channel." The following patch should force the driver to enable/disable the receiver via RXEN/RXDIS fields of the USART control register. It fixed the issue I was having. Signed-off-by: Gabe Siftar <gabe.siftar@getingeusa.com> [nicolas.ferre@atmel.com: slightly modify commit message] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diffstat (limited to 'drivers/tty')
-rw-r--r--drivers/tty/serial/atmel_serial.c4
1 files changed, 4 insertions, 0 deletions
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index f9a6be7..3d7e1ee 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -389,6 +389,8 @@ static void atmel_start_rx(struct uart_port *port)
{
UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */
+ UART_PUT_CR(port, ATMEL_US_RXEN);
+
if (atmel_use_dma_rx(port)) {
/* enable PDC controller */
UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
@@ -404,6 +406,8 @@ static void atmel_start_rx(struct uart_port *port)
*/
static void atmel_stop_rx(struct uart_port *port)
{
+ UART_PUT_CR(port, ATMEL_US_RXDIS);
+
if (atmel_use_dma_rx(port)) {
/* disable PDC receive */
UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS);
OpenPOWER on IntegriCloud