Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup

This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)

To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).

Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.

* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
  ARM: ixp4xx: fix timer latch calculation
  ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
  ARM: rpc: stop using <mach/timex.h>
  ARM: ixp4xx: stop using <mach/timex.h>
  input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
  ARM: at91: don't use <mach/timex.h>
  ARM: ep93xx: stop using mach/timex.h
  ARM: mmp: stop using mach/timex.h
  ARM: netx: stop using mach/timex.h
  ARM: sa1100: stop using mach/timex.h
  clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
  rtc: pxa: drop unused #define TIMER_FREQ
  rtc: at91sam9: include <mach/hardware.h> explicitly
  ARM/serial: at91: switch atmel serial to use gpiolib

Signed-off-by: Olof Johansson <olof@lixom.net>

1 files changed, 31 insertions, 18 deletions

diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index a49f10d..91c0d88 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -35,21 +35,18 @@
 #include <linux/platform_device.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/dma-mapping.h>
 #include <linux/atmel_pdc.h>
 #include <linux/atmel_serial.h>
 #include <linux/uaccess.h>
 #include <linux/platform_data/atmel.h>
 #include <linux/timer.h>
+#include <linux/gpio.h>
 
 #include <asm/io.h>
 #include <asm/ioctls.h>
 
-#ifdef CONFIG_ARM
-#include <mach/cpu.h>
-#include <asm/gpio.h>
-#endif
-
 #define PDC_BUFFER_SIZE		512
 /* Revisit: We should calculate this based on the actual port settings */
 #define PDC_RX_TIMEOUT		(3 * 10)		/* 3 bytes */
@@ -168,6 +165,7 @@ struct atmel_uart_port {
 	struct circ_buf		rx_ring;
 
 	struct serial_rs485	rs485;		/* rs485 settings */
+	int			rts_gpio;	/* optional RTS GPIO */
 	unsigned int		tx_done_mask;
 	bool			is_usart;	/* usart or uart */
 	struct timer_list	uart_timer;	/* uart timer */
@@ -301,20 +299,16 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
 	unsigned int mode;
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
 
-#ifdef CONFIG_ARCH_AT91RM9200
-	if (cpu_is_at91rm9200()) {
-		/*
-		 * AT91RM9200 Errata #39: RTS0 is not internally connected
-		 * to PA21. We need to drive the pin manually.
-		 */
-		if (port->mapbase == AT91RM9200_BASE_US0) {
-			if (mctrl & TIOCM_RTS)
-				at91_set_gpio_value(AT91_PIN_PA21, 0);
-			else
-				at91_set_gpio_value(AT91_PIN_PA21, 1);
-		}
+	/*
+	 * AT91RM9200 Errata #39: RTS0 is not internally connected
+	 * to PA21. We need to drive the pin as a GPIO.
+	 */
+	if (gpio_is_valid(atmel_port->rts_gpio)) {
+		if (mctrl & TIOCM_RTS)
+			gpio_set_value(atmel_port->rts_gpio, 0);
+		else
+			gpio_set_value(atmel_port->rts_gpio, 1);
 	}
-#endif
 
 	if (mctrl & TIOCM_RTS)
 		control |= ATMEL_US_RTSEN;
@@ -2389,6 +2383,25 @@ static int atmel_serial_probe(struct platform_device *pdev)
 	port = &atmel_ports[ret];
 	port->backup_imr = 0;
 	port->uart.line = ret;
+	port->rts_gpio = -EINVAL; /* Invalid, zero could be valid */
+	if (pdata)
+		port->rts_gpio = pdata->rts_gpio;
+	else if (np)
+		port->rts_gpio = of_get_named_gpio(np, "rts-gpios", 0);
+
+	if (gpio_is_valid(port->rts_gpio)) {
+		ret = devm_gpio_request(&pdev->dev, port->rts_gpio, "RTS");
+		if (ret) {
+			dev_err(&pdev->dev, "error requesting RTS GPIO\n");
+			goto err;
+		}
+		/* Default to 1 as RTS is active low */
+		ret = gpio_direction_output(port->rts_gpio, 1);
+		if (ret) {
+			dev_err(&pdev->dev, "error setting up RTS GPIO\n");
+			goto err;
+		}
+	}
 
 	ret = atmel_init_port(port, pdev);
 	if (ret)