zs: move to the serial subsystem

This is a reimplementation of the zs driver for the serial subsystem.  Any
resemblance to the old driver is purely coincidential.  ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...

Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e.  ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3.  It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.

This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1 files changed, 0 insertions, 404 deletions

diff --git a/drivers/tc/zs.h b/drivers/tc/zs.h
deleted file mode 100644
index 1351220..0000000
--- a/drivers/tc/zs.h
+++ /dev/null
@@ -1,404 +0,0 @@
-/*
- * drivers/tc/zs.h: Definitions for the DECstation Z85C30 serial driver.
- *
- * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
- * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen.
- *
- * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- * Copyright (C) 2004, 2005  Maciej W. Rozycki
- */
-#ifndef _DECSERIAL_H
-#define _DECSERIAL_H
-
-#include <asm/dec/serial.h>
-
-#define NUM_ZSREGS 16
-
-struct serial_struct {
-	int	type;
-	int	line;
-	int	port;
-	int	irq;
-	int	flags;
-	int	xmit_fifo_size;
-	int	custom_divisor;
-	int	baud_base;
-	unsigned short	close_delay;
-	char	reserved_char[2];
-	int	hub6;
-	unsigned short	closing_wait; /* time to wait before closing */
-	unsigned short	closing_wait2; /* no longer used... */
-	int	reserved[4];
-};
-
-/*
- * For the close wait times, 0 means wait forever for serial port to
- * flush its output.  65535 means don't wait at all.
- */
-#define ZILOG_CLOSING_WAIT_INF	0
-#define ZILOG_CLOSING_WAIT_NONE	65535
-
-/*
- * Definitions for ZILOG_struct (and serial_struct) flags field
- */
-#define ZILOG_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
-				   on the callout port */
-#define ZILOG_FOURPORT  0x0002	/* Set OU1, OUT2 per AST Fourport settings */
-#define ZILOG_SAK	0x0004	/* Secure Attention Key (Orange book) */
-#define ZILOG_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
-
-#define ZILOG_SPD_MASK	0x0030
-#define ZILOG_SPD_HI	0x0010	/* Use 56000 instead of 38400 bps */
-
-#define ZILOG_SPD_VHI	0x0020  /* Use 115200 instead of 38400 bps */
-#define ZILOG_SPD_CUST	0x0030  /* Use user-specified divisor */
-
-#define ZILOG_SKIP_TEST	0x0040 /* Skip UART test during autoconfiguration */
-#define ZILOG_AUTO_IRQ  0x0080 /* Do automatic IRQ during autoconfiguration */
-#define ZILOG_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
-#define ZILOG_PGRP_LOCKOUT    0x0200 /* Lock out cua opens based on pgrp */
-#define ZILOG_CALLOUT_NOHUP   0x0400 /* Don't do hangups for cua device */
-
-#define ZILOG_FLAGS	0x0FFF	/* Possible legal ZILOG flags */
-#define ZILOG_USR_MASK 0x0430	/* Legal flags that non-privileged
-				 * users can set or reset */
-
-/* Internal flags used only by kernel/chr_drv/serial.c */
-#define ZILOG_INITIALIZED	0x80000000 /* Serial port was initialized */
-#define ZILOG_CALLOUT_ACTIVE	0x40000000 /* Call out device is active */
-#define ZILOG_NORMAL_ACTIVE	0x20000000 /* Normal device is active */
-#define ZILOG_BOOT_AUTOCONF	0x10000000 /* Autoconfigure port on bootup */
-#define ZILOG_CLOSING		0x08000000 /* Serial port is closing */
-#define ZILOG_CTS_FLOW		0x04000000 /* Do CTS flow control */
-#define ZILOG_CHECK_CD		0x02000000 /* i.e., CLOCAL */
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct dec_zschannel {
-	volatile unsigned char *control;
-	volatile unsigned char *data;
-
-	/* Current write register values */
-	unsigned char curregs[NUM_ZSREGS];
-};
-
-struct dec_serial {
-	struct dec_serial	*zs_next;	/* For IRQ servicing chain.  */
-	struct dec_zschannel	*zs_channel;	/* Channel registers.  */
-	struct dec_zschannel	*zs_chan_a;	/* A side registers.  */
-	unsigned char		read_reg_zero;
-
-	struct dec_serial_hook	*hook;		/* Hook on this channel.  */
-	int			tty_break;	/* Set on BREAK condition.  */
-	int			is_cons;	/* Is this our console.  */
-	int			tx_active;	/* Char is being xmitted.  */
-	int			tx_stopped;	/* Output is suspended.  */
-
-	/*
-	 * We need to know the current clock divisor
-	 * to read the bps rate the chip has currently loaded.
-	 */
-	int			clk_divisor;	/* May be 1, 16, 32, or 64.  */
-	int			zs_baud;
-
-	char			change_needed;
-
-	int			magic;
-	int			baud_base;
-	int			port;
-	int			irq;
-	int			flags; 		/* Defined in tty.h.  */
-	int			type; 		/* UART type.  */
-	struct tty_struct 	*tty;
-	int			read_status_mask;
-	int			ignore_status_mask;
-	int			timeout;
-	int			xmit_fifo_size;
-	int			custom_divisor;
-	int			x_char;		/* XON/XOFF character.  */
-	int			close_delay;
-	unsigned short		closing_wait;
-	unsigned short		closing_wait2;
-	unsigned long		event;
-	unsigned long		last_active;
-	int			line;
-	int			count;		/* # of fds on device.  */
-	int			blocked_open;	/* # of blocked opens.  */
-	unsigned char 		*xmit_buf;
-	int			xmit_head;
-	int			xmit_tail;
-	int			xmit_cnt;
-	struct tasklet_struct	tlet;
-	wait_queue_head_t	open_wait;
-	wait_queue_head_t	close_wait;
-};
-
-
-#define SERIAL_MAGIC 0x5301
-
-/*
- * The size of the serial xmit buffer is 1 page, or 4096 bytes
- */
-#define SERIAL_XMIT_SIZE 4096
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP	0
-
-#endif /* __KERNEL__ */
-
-/* Conversion routines to/from brg time constants from/to bits
- * per second.
- */
-#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
-#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
-
-/* The Zilog register set */
-
-#define	FLAG	0x7e
-
-/* Write Register 0 */
-#define	R0	0		/* Register selects */
-#define	R1	1
-#define	R2	2
-#define	R3	3
-#define	R4	4
-#define	R5	5
-#define	R6	6
-#define	R7	7
-#define	R8	8
-#define	R9	9
-#define	R10	10
-#define	R11	11
-#define	R12	12
-#define	R13	13
-#define	R14	14
-#define	R15	15
-
-#define	NULLCODE	0	/* Null Code */
-#define	POINT_HIGH	0x8	/* Select upper half of registers */
-#define	RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */
-#define	SEND_ABORT	0x18	/* HDLC Abort */
-#define	RES_RxINT_FC	0x20	/* Reset RxINT on First Character */
-#define	RES_Tx_P	0x28	/* Reset TxINT Pending */
-#define	ERR_RES		0x30	/* Error Reset */
-#define	RES_H_IUS	0x38	/* Reset highest IUS */
-
-#define	RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */
-#define	RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */
-#define	RES_EOM_L	0xC0	/* Reset EOM latch */
-
-/* Write Register 1 */
-
-#define	EXT_INT_ENAB	0x1	/* Ext Int Enable */
-#define	TxINT_ENAB	0x2	/* Tx Int Enable */
-#define	PAR_SPEC	0x4	/* Parity is special condition */
-
-#define	RxINT_DISAB	0	/* Rx Int Disable */
-#define	RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */
-#define	RxINT_ALL	0x10	/* Int on all Rx Characters or error */
-#define	RxINT_ERR	0x18	/* Int on error only */
-#define	RxINT_MASK	0x18
-
-#define	WT_RDY_RT	0x20	/* Wait/Ready on R/T */
-#define	WT_FN_RDYFN	0x40	/* Wait/FN/Ready FN */
-#define	WT_RDY_ENAB	0x80	/* Wait/Ready Enable */
-
-/* Write Register #2 (Interrupt Vector) */
-
-/* Write Register 3 */
-
-#define	RxENABLE	0x1	/* Rx Enable */
-#define	SYNC_L_INH	0x2	/* Sync Character Load Inhibit */
-#define	ADD_SM		0x4	/* Address Search Mode (SDLC) */
-#define	RxCRC_ENAB	0x8	/* Rx CRC Enable */
-#define	ENT_HM		0x10	/* Enter Hunt Mode */
-#define	AUTO_ENAB	0x20	/* Auto Enables */
-#define	Rx5		0x0	/* Rx 5 Bits/Character */
-#define	Rx7		0x40	/* Rx 7 Bits/Character */
-#define	Rx6		0x80	/* Rx 6 Bits/Character */
-#define	Rx8		0xc0	/* Rx 8 Bits/Character */
-#define RxNBITS_MASK	0xc0
-
-/* Write Register 4 */
-
-#define	PAR_ENA		0x1	/* Parity Enable */
-#define	PAR_EVEN	0x2	/* Parity Even/Odd* */
-
-#define	SYNC_ENAB	0	/* Sync Modes Enable */
-#define	SB1		0x4	/* 1 stop bit/char */
-#define	SB15		0x8	/* 1.5 stop bits/char */
-#define	SB2		0xc	/* 2 stop bits/char */
-#define SB_MASK		0xc
-
-#define	MONSYNC		0	/* 8 Bit Sync character */
-#define	BISYNC		0x10	/* 16 bit sync character */
-#define	SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */
-#define	EXTSYNC		0x30	/* External Sync Mode */
-
-#define	X1CLK		0x0	/* x1 clock mode */
-#define	X16CLK		0x40	/* x16 clock mode */
-#define	X32CLK		0x80	/* x32 clock mode */
-#define	X64CLK		0xC0	/* x64 clock mode */
-#define XCLK_MASK	0xC0
-
-/* Write Register 5 */
-
-#define	TxCRC_ENAB	0x1	/* Tx CRC Enable */
-#define	RTS		0x2	/* RTS */
-#define	SDLC_CRC	0x4	/* SDLC/CRC-16 */
-#define	TxENAB		0x8	/* Tx Enable */
-#define	SND_BRK		0x10	/* Send Break */
-#define	Tx5		0x0	/* Tx 5 bits (or less)/character */
-#define	Tx7		0x20	/* Tx 7 bits/character */
-#define	Tx6		0x40	/* Tx 6 bits/character */
-#define	Tx8		0x60	/* Tx 8 bits/character */
-#define TxNBITS_MASK	0x60
-#define	DTR		0x80	/* DTR */
-
-/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
-
-/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
-
-/* Write Register 8 (transmit buffer) */
-
-/* Write Register 9 (Master interrupt control) */
-#define	VIS	1	/* Vector Includes Status */
-#define	NV	2	/* No Vector */
-#define	DLC	4	/* Disable Lower Chain */
-#define	MIE	8	/* Master Interrupt Enable */
-#define	STATHI	0x10	/* Status high */
-#define	SOFTACK	0x20	/* Software Interrupt Acknowledge */
-#define	NORESET	0	/* No reset on write to R9 */
-#define	CHRB	0x40	/* Reset channel B */
-#define	CHRA	0x80	/* Reset channel A */
-#define	FHWRES	0xc0	/* Force hardware reset */
-
-/* Write Register 10 (misc control bits) */
-#define	BIT6	1	/* 6 bit/8bit sync */
-#define	LOOPMODE 2	/* SDLC Loop mode */
-#define	ABUNDER	4	/* Abort/flag on SDLC xmit underrun */
-#define	MARKIDLE 8	/* Mark/flag on idle */
-#define	GAOP	0x10	/* Go active on poll */
-#define	NRZ	0	/* NRZ mode */
-#define	NRZI	0x20	/* NRZI mode */
-#define	FM1	0x40	/* FM1 (transition = 1) */
-#define	FM0	0x60	/* FM0 (transition = 0) */
-#define	CRCPS	0x80	/* CRC Preset I/O */
-
-/* Write Register 11 (Clock Mode control) */
-#define	TRxCXT	0	/* TRxC = Xtal output */
-#define	TRxCTC	1	/* TRxC = Transmit clock */
-#define	TRxCBR	2	/* TRxC = BR Generator Output */
-#define	TRxCDP	3	/* TRxC = DPLL output */
-#define	TRxCOI	4	/* TRxC O/I */
-#define	TCRTxCP	0	/* Transmit clock = RTxC pin */
-#define	TCTRxCP	8	/* Transmit clock = TRxC pin */
-#define	TCBR	0x10	/* Transmit clock = BR Generator output */
-#define	TCDPLL	0x18	/* Transmit clock = DPLL output */
-#define	RCRTxCP	0	/* Receive clock = RTxC pin */
-#define	RCTRxCP	0x20	/* Receive clock = TRxC pin */
-#define	RCBR	0x40	/* Receive clock = BR Generator output */
-#define	RCDPLL	0x60	/* Receive clock = DPLL output */
-#define	RTxCX	0x80	/* RTxC Xtal/No Xtal */
-
-/* Write Register 12 (lower byte of baud rate generator time constant) */
-
-/* Write Register 13 (upper byte of baud rate generator time constant) */
-
-/* Write Register 14 (Misc control bits) */
-#define	BRENABL	1	/* Baud rate generator enable */
-#define	BRSRC	2	/* Baud rate generator source */
-#define	DTRREQ	4	/* DTR/Request function */
-#define	AUTOECHO 8	/* Auto Echo */
-#define	LOOPBAK	0x10	/* Local loopback */
-#define	SEARCH	0x20	/* Enter search mode */
-#define	RMC	0x40	/* Reset missing clock */
-#define	DISDPLL	0x60	/* Disable DPLL */
-#define	SSBR	0x80	/* Set DPLL source = BR generator */
-#define	SSRTxC	0xa0	/* Set DPLL source = RTxC */
-#define	SFMM	0xc0	/* Set FM mode */
-#define	SNRZI	0xe0	/* Set NRZI mode */
-
-/* Write Register 15 (external/status interrupt control) */
-#define	ZCIE	2	/* Zero count IE */
-#define	DCDIE	8	/* DCD IE */
-#define	SYNCIE	0x10	/* Sync/hunt IE */
-#define	CTSIE	0x20	/* CTS IE */
-#define	TxUIE	0x40	/* Tx Underrun/EOM IE */
-#define	BRKIE	0x80	/* Break/Abort IE */
-
-
-/* Read Register 0 */
-#define	Rx_CH_AV	0x1	/* Rx Character Available */
-#define	ZCOUNT		0x2	/* Zero count */
-#define	Tx_BUF_EMP	0x4	/* Tx Buffer empty */
-#define	DCD		0x8	/* DCD */
-#define	SYNC_HUNT	0x10	/* Sync/hunt */
-#define	CTS		0x20	/* CTS */
-#define	TxEOM		0x40	/* Tx underrun */
-#define	BRK_ABRT	0x80	/* Break/Abort */
-
-/* Read Register 1 */
-#define	ALL_SNT		0x1	/* All sent */
-/* Residue Data for 8 Rx bits/char programmed */
-#define	RES3		0x8	/* 0/3 */
-#define	RES4		0x4	/* 0/4 */
-#define	RES5		0xc	/* 0/5 */
-#define	RES6		0x2	/* 0/6 */
-#define	RES7		0xa	/* 0/7 */
-#define	RES8		0x6	/* 0/8 */
-#define	RES18		0xe	/* 1/8 */
-#define	RES28		0x0	/* 2/8 */
-/* Special Rx Condition Interrupts */
-#define	PAR_ERR		0x10	/* Parity error */
-#define	Rx_OVR		0x20	/* Rx Overrun Error */
-#define	FRM_ERR		0x40	/* CRC/Framing Error */
-#define	END_FR		0x80	/* End of Frame (SDLC) */
-
-/* Read Register 2 (channel b only) - Interrupt vector */
-
-/* Read Register 3 (interrupt pending register) ch a only */
-#define	CHBEXT	0x1		/* Channel B Ext/Stat IP */
-#define	CHBTxIP	0x2		/* Channel B Tx IP */
-#define	CHBRxIP	0x4		/* Channel B Rx IP */
-#define	CHAEXT	0x8		/* Channel A Ext/Stat IP */
-#define	CHATxIP	0x10		/* Channel A Tx IP */
-#define	CHARxIP	0x20		/* Channel A Rx IP */
-
-/* Read Register 8 (receive data register) */
-
-/* Read Register 10  (misc status bits) */
-#define	ONLOOP	2		/* On loop */
-#define	LOOPSEND 0x10		/* Loop sending */
-#define	CLK2MIS	0x40		/* Two clocks missing */
-#define	CLK1MIS	0x80		/* One clock missing */
-
-/* Read Register 12 (lower byte of baud rate generator constant) */
-
-/* Read Register 13 (upper byte of baud rate generator constant) */
-
-/* Read Register 15 (value of WR 15) */
-
-/* Misc macros */
-#define ZS_CLEARERR(channel)	(write_zsreg(channel, 0, ERR_RES))
-#define ZS_CLEARFIFO(channel)	do { volatile unsigned char garbage; \
-				     garbage = read_zsdata(channel); \
-				     garbage = read_zsdata(channel); \
-				     garbage = read_zsdata(channel); \
-				} while(0)
-
-#endif /* !(_DECSERIAL_H) */