lk201: remove obsolete driver

Remove the old-fashioned lk201 driver under drivers/tc/ that used to be
used by the old dz.c and zs.c drivers, which is now orphan code referred to
from nowhere and does not build anymore.  A modern replacement is available
as drivers/input/keyboard/lkkbd.c.

There are no plans to do anything about this piece of code and it does not
fit anywhere anymore, so it is not just a matter of maintenance or the lack
of.  There are still some bits that might be added to the new lkkbd.c
driver based on the old code, and the embedded hardware documentation which
is otherwise quite hard to get hold of might be useful to keep too.  Both
of these can be done separately though.  RIP.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1 files changed, 0 insertions, 125 deletions

diff --git a/drivers/tc/lk201.h b/drivers/tc/lk201.h
deleted file mode 100644
index 99f3203..0000000
--- a/drivers/tc/lk201.h
+++ /dev/null
@@ -1,125 +0,0 @@
-/*
- *	Commands to the keyboard processor
- */
-
-#define LK_PARAM		0x80	/* start/end parameter list */
-
-#define LK_CMD_RESUME		0x8b	/* resume transmission to the host */
-#define LK_CMD_INHIBIT		0x89	/* stop transmission to the host */
-#define LK_CMD_LEDS_ON		0x13	/* light LEDs */
-					/* 1st param: led bitmask */
-#define LK_CMD_LEDS_OFF		0x11	/* turn off LEDs */
-					/* 1st param: led bitmask */
-#define LK_CMD_DIS_KEYCLK	0x99	/* disable the keyclick */
-#define LK_CMD_ENB_KEYCLK	0x1b	/* enable the keyclick */
-					/* 1st param: volume */
-#define LK_CMD_DIS_CTLCLK	0xb9	/* disable the Ctrl keyclick */
-#define LK_CMD_ENB_CTLCLK	0xbb	/* enable the Ctrl keyclick */
-#define LK_CMD_SOUND_CLK	0x9f	/* emit a keyclick */
-#define LK_CMD_DIS_BELL		0xa1	/* disable the bell */
-#define LK_CMD_ENB_BELL		0x23	/* enable the bell */
-					/* 1st param: volume */
-#define LK_CMD_BELL		0xa7	/* emit a bell */
-#define LK_CMD_TMP_NORPT	0xd1	/* disable typematic */
-					/* for the currently pressed key */
-#define LK_CMD_ENB_RPT		0xe3	/* enable typematic */
-					/* for RPT_DOWN groups */
-#define LK_CMD_DIS_RPT		0xe1	/* disable typematic */
-					/* for RPT_DOWN groups */
-#define LK_CMD_RPT_TO_DOWN	0xd9	/* set RPT_DOWN groups to DOWN */
-#define LK_CMD_REQ_ID		0xab	/* request the keyboard ID */
-#define LK_CMD_POWER_UP		0xfd	/* init power-up sequence */
-#define LK_CMD_TEST_MODE	0xcb	/* enter the factory test mode */
-#define LK_CMD_TEST_EXIT	0x80	/* exit the factory test mode */
-#define LK_CMD_SET_DEFAULTS	0xd3	/* set power-up defaults */
-
-#define LK_CMD_MODE(m,div)	(LK_PARAM|(((div)&0xf)<<3)|(((m)&0x3)<<1))
-					/* select the repeat mode */
-					/* for the selected key group */
-#define LK_CMD_MODE_AR(m,div)	((((div)&0xf)<<3)|(((m)&0x3)<<1))
-					/* select the repeat mode */
-					/* and the repeat register */
-					/* for the selected key group */
-					/* 1st param: register number */
-#define LK_CMD_RPT_RATE(r)	(0x78|(((r)&0x3)<<1))
-					/* set the delay and repeat rate */
-					/* for the selected repeat register */
-					/* 1st param: initial delay */
-					/* 2nd param: repeat rate */
-
-/* there are 4 leds, represent them in the low 4 bits of a byte */
-#define LK_PARAM_LED_MASK(ledbmap)	(LK_PARAM|((ledbmap)&0xf))
-#define LK_LED_WAIT		0x1	/* Wait LED */
-#define LK_LED_COMP		0x2	/* Compose LED */
-#define LK_LED_LOCK		0x4	/* Lock LED */
-#define LK_LED_HOLD		0x8	/* Hold Screen LED */
-
-/* max volume is 0, lowest is 0x7 */
-#define LK_PARAM_VOLUME(v)		(LK_PARAM|((v)&0x7))
-
-/* mode set command details, div is a key group number */
-#define LK_MODE_DOWN		0x0	/* make only */
-#define LK_MODE_RPT_DOWN	0x1	/* make and typematic */
-#define LK_MODE_DOWN_UP		0x3	/* make and release */
-
-/* there are 4 repeat registers */
-#define LK_PARAM_AR(r)		(LK_PARAM|((v)&0x3))
-
-/*
- * Mappings between key groups and keycodes are as follows:
- *
- *  1: 0xbf - 0xff -- alphanumeric,
- *  2: 0x91 - 0xa5 -- numeric keypad,
- *  3: 0xbc        -- Backspace,
- *  4: 0xbd - 0xbe -- Tab, Return,
- *  5: 0xb0 - 0xb2 -- Lock, Compose Character,
- *  6: 0xad - 0xaf -- Ctrl, Shift,
- *  7: 0xa6 - 0xa8 -- Left Arrow, Right Arrow,
- *  8: 0xa9 - 0xac -- Up Arrow, Down Arrow, Right Shift,
- *  9: 0x88 - 0x90 -- editor keypad,
- * 10: 0x56 - 0x62 -- F1 - F5,
- * 11: 0x63 - 0x6e -- F6 - F10,
- * 12: 0x6f - 0x7a -- F11 - F14,
- * 13: 0x7b - 0x7d -- Help, Do,
- * 14: 0x7e - 0x87 -- F17 - F20.
- *
- * Notes:
- * 1. Codes in the 0x00 - 0x40 range are reserved.
- * 2. The assignment of the 0x41 - 0x55 range is undiscovered, probably 10.
- */
-
-/* delay is 5 - 630 ms; 0x00 and 0x7f are reserved */
-#define LK_PARAM_DELAY(t)	((t)&0x7f)
-
-/* rate is 12 - 127 Hz; 0x00 - 0x0b and 0x7d (power-up!) are reserved */
-#define LK_PARAM_RATE(r)	(LK_PARAM|((r)&0x7f))
-
-#define LK_SHIFT 1<<0
-#define LK_CTRL 1<<1
-#define LK_LOCK 1<<2
-#define LK_COMP 1<<3
-
-#define LK_KEY_SHIFT		0xae
-#define LK_KEY_CTRL		0xaf
-#define LK_KEY_LOCK		0xb0
-#define LK_KEY_COMP		0xb1
-
-#define LK_KEY_RELEASE		0xb3	/* all keys released */
-#define LK_KEY_REPEAT		0xb4	/* repeat the last key */
-
-/* status responses */
-#define LK_STAT_RESUME_ERR	0xb5	/* keystrokes lost while inhibited */
-#define LK_STAT_ERROR		0xb6	/* an invalid command received */
-#define LK_STAT_INHIBIT_ACK	0xb7	/* transmission inhibited */
-#define LK_STAT_TEST_ACK	0xb8	/* the factory test mode entered */
-#define LK_STAT_MODE_KEYDOWN	0xb9	/* a key is down on a change */
-					/* to the DOWN_UP mode; */
-					/* the keycode follows */
-#define LK_STAT_MODE_ACK	0xba	/* the mode command succeeded */
-
-#define LK_STAT_PWRUP_ID	0x01	/* the power-up response start mark */
-#define LK_STAT_PWRUP_OK	0x00	/* the power-up self test OK */
-#define LK_STAT_PWRUP_KDOWN	0x3d	/* a key was down during the test */
-#define LK_STAT_PWRUP_ERROR	0x3e	/* keyboard self test failure */
-
-extern unsigned char scancodeRemap[256];