Merge commit 'origin'

Manual fixup of conflicts on:

	arch/powerpc/include/asm/dcr-regs.h
	drivers/net/ibm_newemac/core.h

4 files changed, 111 insertions, 39 deletions

diff --git a/drivers/spi/orion_spi.c b/drivers/spi/orion_spi.c
index c4eaacd..b872bfa 100644
--- a/drivers/spi/orion_spi.c
+++ b/drivers/spi/orion_spi.c
@@ -427,7 +427,7 @@ static int orion_spi_transfer(struct spi_device *spi, struct spi_message *m)
 			goto msg_rejected;
 		}
 
-		if (t->speed_hz < orion_spi->min_speed) {
+		if (t->speed_hz && t->speed_hz < orion_spi->min_speed) {
 			dev_err(&spi->dev,
 				"message rejected : "
 				"device min speed (%d Hz) exceeds "
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 34c7c98..d47d363 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -47,9 +47,10 @@ MODULE_ALIAS("platform:pxa2xx-spi");
 
 #define MAX_BUSES 3
 
-#define DMA_INT_MASK (DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
-#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
-#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0)
+#define DMA_INT_MASK		(DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
+#define RESET_DMA_CHANNEL	(DCSR_NODESC | DMA_INT_MASK)
+#define IS_DMA_ALIGNED(x)	((((u32)(x)) & 0x07) == 0)
+#define MAX_DMA_LEN		8191
 
 /*
  * for testing SSCR1 changes that require SSP restart, basically
@@ -144,7 +145,6 @@ struct driver_data {
 	size_t tx_map_len;
 	u8 n_bytes;
 	u32 dma_width;
-	int cs_change;
 	int (*write)(struct driver_data *drv_data);
 	int (*read)(struct driver_data *drv_data);
 	irqreturn_t (*transfer_handler)(struct driver_data *drv_data);
@@ -406,8 +406,45 @@ static void giveback(struct driver_data *drv_data)
 					struct spi_transfer,
 					transfer_list);
 
+	/* Delay if requested before any change in chip select */
+	if (last_transfer->delay_usecs)
+		udelay(last_transfer->delay_usecs);
+
+	/* Drop chip select UNLESS cs_change is true or we are returning
+	 * a message with an error, or next message is for another chip
+	 */
 	if (!last_transfer->cs_change)
 		drv_data->cs_control(PXA2XX_CS_DEASSERT);
+	else {
+		struct spi_message *next_msg;
+
+		/* Holding of cs was hinted, but we need to make sure
+		 * the next message is for the same chip.  Don't waste
+		 * time with the following tests unless this was hinted.
+		 *
+		 * We cannot postpone this until pump_messages, because
+		 * after calling msg->complete (below) the driver that
+		 * sent the current message could be unloaded, which
+		 * could invalidate the cs_control() callback...
+		 */
+
+		/* get a pointer to the next message, if any */
+		spin_lock_irqsave(&drv_data->lock, flags);
+		if (list_empty(&drv_data->queue))
+			next_msg = NULL;
+		else
+			next_msg = list_entry(drv_data->queue.next,
+					struct spi_message, queue);
+		spin_unlock_irqrestore(&drv_data->lock, flags);
+
+		/* see if the next and current messages point
+		 * to the same chip
+		 */
+		if (next_msg && next_msg->spi != msg->spi)
+			next_msg = NULL;
+		if (!next_msg || msg->state == ERROR_STATE)
+			drv_data->cs_control(PXA2XX_CS_DEASSERT);
+	}
 
 	msg->state = NULL;
 	if (msg->complete)
@@ -490,10 +527,9 @@ static void dma_transfer_complete(struct driver_data *drv_data)
 	msg->actual_length += drv_data->len -
 				(drv_data->rx_end - drv_data->rx);
 
-	/* Release chip select if requested, transfer delays are
-	 * handled in pump_transfers */
-	if (drv_data->cs_change)
-		drv_data->cs_control(PXA2XX_CS_DEASSERT);
+	/* Transfer delays and chip select release are
+	 * handled in pump_transfers or giveback
+	 */
 
 	/* Move to next transfer */
 	msg->state = next_transfer(drv_data);
@@ -602,10 +638,9 @@ static void int_transfer_complete(struct driver_data *drv_data)
 	drv_data->cur_msg->actual_length += drv_data->len -
 				(drv_data->rx_end - drv_data->rx);
 
-	/* Release chip select if requested, transfer delays are
-	 * handled in pump_transfers */
-	if (drv_data->cs_change)
-		drv_data->cs_control(PXA2XX_CS_DEASSERT);
+	/* Transfer delays and chip select release are
+	 * handled in pump_transfers or giveback
+	 */
 
 	/* Move to next transfer */
 	drv_data->cur_msg->state = next_transfer(drv_data);
@@ -840,23 +875,40 @@ static void pump_transfers(unsigned long data)
 		return;
 	}
 
-	/* Delay if requested at end of transfer*/
+	/* Delay if requested at end of transfer before CS change */
 	if (message->state == RUNNING_STATE) {
 		previous = list_entry(transfer->transfer_list.prev,
 					struct spi_transfer,
 					transfer_list);
 		if (previous->delay_usecs)
 			udelay(previous->delay_usecs);
+
+		/* Drop chip select only if cs_change is requested */
+		if (previous->cs_change)
+			drv_data->cs_control(PXA2XX_CS_DEASSERT);
 	}
 
-	/* Check transfer length */
-	if (transfer->len > 8191)
-	{
-		dev_warn(&drv_data->pdev->dev, "pump_transfers: transfer "
-				"length greater than 8191\n");
-		message->status = -EINVAL;
-		giveback(drv_data);
-		return;
+	/* Check for transfers that need multiple DMA segments */
+	if (transfer->len > MAX_DMA_LEN && chip->enable_dma) {
+
+		/* reject already-mapped transfers; PIO won't always work */
+		if (message->is_dma_mapped
+				|| transfer->rx_dma || transfer->tx_dma) {
+			dev_err(&drv_data->pdev->dev,
+				"pump_transfers: mapped transfer length "
+				"of %u is greater than %d\n",
+				transfer->len, MAX_DMA_LEN);
+			message->status = -EINVAL;
+			giveback(drv_data);
+			return;
+		}
+
+		/* warn ... we force this to PIO mode */
+		if (printk_ratelimit())
+			dev_warn(&message->spi->dev, "pump_transfers: "
+				"DMA disabled for transfer length %ld "
+				"greater than %d\n",
+				(long)drv_data->len, MAX_DMA_LEN);
 	}
 
 	/* Setup the transfer state based on the type of transfer */
@@ -878,7 +930,6 @@ static void pump_transfers(unsigned long data)
 	drv_data->len = transfer->len & DCMD_LENGTH;
 	drv_data->write = drv_data->tx ? chip->write : null_writer;
 	drv_data->read = drv_data->rx ? chip->read : null_reader;
-	drv_data->cs_change = transfer->cs_change;
 
 	/* Change speed and bit per word on a per transfer */
 	cr0 = chip->cr0;
@@ -925,7 +976,7 @@ static void pump_transfers(unsigned long data)
 							&dma_thresh))
 				if (printk_ratelimit())
 					dev_warn(&message->spi->dev,
-						"pump_transfer: "
+						"pump_transfers: "
 						"DMA burst size reduced to "
 						"match bits_per_word\n");
 		}
@@ -939,8 +990,23 @@ static void pump_transfers(unsigned long data)
 
 	message->state = RUNNING_STATE;
 
-	/* Try to map dma buffer and do a dma transfer if successful */
-	if ((drv_data->dma_mapped = map_dma_buffers(drv_data))) {
+	/* Try to map dma buffer and do a dma transfer if successful, but
+	 * only if the length is non-zero and less than MAX_DMA_LEN.
+	 *
+	 * Zero-length non-descriptor DMA is illegal on PXA2xx; force use
+	 * of PIO instead.  Care is needed above because the transfer may
+	 * have have been passed with buffers that are already dma mapped.
+	 * A zero-length transfer in PIO mode will not try to write/read
+	 * to/from the buffers
+	 *
+	 * REVISIT large transfers are exactly where we most want to be
+	 * using DMA.  If this happens much, split those transfers into
+	 * multiple DMA segments rather than forcing PIO.
+	 */
+	drv_data->dma_mapped = 0;
+	if (drv_data->len > 0 && drv_data->len <= MAX_DMA_LEN)
+		drv_data->dma_mapped = map_dma_buffers(drv_data);
+	if (drv_data->dma_mapped) {
 
 		/* Ensure we have the correct interrupt handler */
 		drv_data->transfer_handler = dma_transfer;
diff --git a/drivers/spi/spi_mpc83xx.c b/drivers/spi/spi_mpc83xx.c
index 070c621..ac0e3e4 100644
--- a/drivers/spi/spi_mpc83xx.c
+++ b/drivers/spi/spi_mpc83xx.c
@@ -267,16 +267,13 @@ int mpc83xx_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 	cs->hw_mode |= SPMODE_LEN(bits_per_word);
 
 	if ((mpc83xx_spi->spibrg / hz) > 64) {
+		cs->hw_mode |= SPMODE_DIV16;
 		pm = mpc83xx_spi->spibrg / (hz * 64);
 		if (pm > 16) {
-			cs->hw_mode |= SPMODE_DIV16;
-			pm /= 16;
-			if (pm > 16) {
-				dev_err(&spi->dev, "Requested speed is too "
-					"low: %d Hz. Will use %d Hz instead.\n",
-					hz, mpc83xx_spi->spibrg / 1024);
-				pm = 16;
-			}
+			dev_err(&spi->dev, "Requested speed is too "
+				"low: %d Hz. Will use %d Hz instead.\n",
+				hz, mpc83xx_spi->spibrg / 1024);
+			pm = 16;
 		}
 	} else
 		pm = mpc83xx_spi->spibrg / (hz * 4);
@@ -315,11 +312,20 @@ static int mpc83xx_spi_bufs(struct spi_device *spi, struct spi_transfer *t)
 	if (t->bits_per_word)
 		bits_per_word = t->bits_per_word;
 	len = t->len;
-	if (bits_per_word > 8)
+	if (bits_per_word > 8) {
+		/* invalid length? */
+		if (len & 1)
+			return -EINVAL;
 		len /= 2;
-	if (bits_per_word > 16)
+	}
+	if (bits_per_word > 16) {
+		/* invalid length? */
+		if (len & 1)
+			return -EINVAL;
 		len /= 2;
+	}
 	mpc83xx_spi->count = len;
+
 	INIT_COMPLETION(mpc83xx_spi->done);
 
 	/* enable rx ints */
diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c
index 98abc73..3eb414b 100644
--- a/drivers/spi/spi_s3c24xx.c
+++ b/drivers/spi/spi_s3c24xx.c
@@ -430,7 +430,7 @@ static int s3c24xx_spi_resume(struct platform_device *pdev)
 #endif
 
 MODULE_ALIAS("platform:s3c2410-spi");
-static struct platform_driver s3c24xx_spidrv = {
+static struct platform_driver s3c24xx_spi_driver = {
 	.remove		= __exit_p(s3c24xx_spi_remove),
 	.suspend	= s3c24xx_spi_suspend,
 	.resume		= s3c24xx_spi_resume,
@@ -442,12 +442,12 @@ static struct platform_driver s3c24xx_spidrv = {
 
 static int __init s3c24xx_spi_init(void)
 {
-        return platform_driver_probe(&s3c24xx_spidrv, s3c24xx_spi_probe);
+        return platform_driver_probe(&s3c24xx_spi_driver, s3c24xx_spi_probe);
 }
 
 static void __exit s3c24xx_spi_exit(void)
 {
-        platform_driver_unregister(&s3c24xx_spidrv);
+        platform_driver_unregister(&s3c24xx_spi_driver);
 }
 
 module_init(s3c24xx_spi_init);