spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

3 files changed, 0 insertions, 401 deletions

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 4a6fe01..83a185d 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -230,17 +230,6 @@ config SPI_XILINX
 #
 comment "SPI Protocol Masters"
 
-config SPI_AT25
-	tristate "SPI EEPROMs from most vendors"
-	depends on SYSFS
-	help
-	  Enable this driver to get read/write support to most SPI EEPROMs,
-	  after you configure the board init code to know about each eeprom
-	  on your target board.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called at25.
-
 config SPI_SPIDEV
 	tristate "User mode SPI device driver support"
 	depends on EXPERIMENTAL
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 5e9f521..5d04519 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -33,7 +33,6 @@ obj-$(CONFIG_SPI_SH_SCI)		+= spi_sh_sci.o
 # 	... add above this line ...
 
 # SPI protocol drivers (device/link on bus)
-obj-$(CONFIG_SPI_AT25)		+= at25.o
 obj-$(CONFIG_SPI_SPIDEV)	+= spidev.o
 obj-$(CONFIG_SPI_TLE62X0)	+= tle62x0.o
 # 	... add above this line ...
diff --git a/drivers/spi/at25.c b/drivers/spi/at25.c
deleted file mode 100644
index 290dbe9..0000000
--- a/drivers/spi/at25.c
+++ /dev/null
@@ -1,389 +0,0 @@
-/*
- * at25.c -- support most SPI EEPROMs, such as Atmel AT25 models
- *
- * Copyright (C) 2006 David Brownell
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <linux/sched.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/eeprom.h>
-
-
-/*
- * NOTE: this is an *EEPROM* driver.  The vagaries of product naming
- * mean that some AT25 products are EEPROMs, and others are FLASH.
- * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver,
- * not this one!
- */
-
-struct at25_data {
-	struct spi_device	*spi;
-	struct mutex		lock;
-	struct spi_eeprom	chip;
-	struct bin_attribute	bin;
-	unsigned		addrlen;
-};
-
-#define	AT25_WREN	0x06		/* latch the write enable */
-#define	AT25_WRDI	0x04		/* reset the write enable */
-#define	AT25_RDSR	0x05		/* read status register */
-#define	AT25_WRSR	0x01		/* write status register */
-#define	AT25_READ	0x03		/* read byte(s) */
-#define	AT25_WRITE	0x02		/* write byte(s)/sector */
-
-#define	AT25_SR_nRDY	0x01		/* nRDY = write-in-progress */
-#define	AT25_SR_WEN	0x02		/* write enable (latched) */
-#define	AT25_SR_BP0	0x04		/* BP for software writeprotect */
-#define	AT25_SR_BP1	0x08
-#define	AT25_SR_WPEN	0x80		/* writeprotect enable */
-
-
-#define EE_MAXADDRLEN	3		/* 24 bit addresses, up to 2 MBytes */
-
-/* Specs often allow 5 msec for a page write, sometimes 20 msec;
- * it's important to recover from write timeouts.
- */
-#define	EE_TIMEOUT	25
-
-/*-------------------------------------------------------------------------*/
-
-#define	io_limit	PAGE_SIZE	/* bytes */
-
-static ssize_t
-at25_ee_read(
-	struct at25_data	*at25,
-	char			*buf,
-	unsigned		offset,
-	size_t			count
-)
-{
-	u8			command[EE_MAXADDRLEN + 1];
-	u8			*cp;
-	ssize_t			status;
-	struct spi_transfer	t[2];
-	struct spi_message	m;
-
-	cp = command;
-	*cp++ = AT25_READ;
-
-	/* 8/16/24-bit address is written MSB first */
-	switch (at25->addrlen) {
-	default:	/* case 3 */
-		*cp++ = offset >> 16;
-	case 2:
-		*cp++ = offset >> 8;
-	case 1:
-	case 0:	/* can't happen: for better codegen */
-		*cp++ = offset >> 0;
-	}
-
-	spi_message_init(&m);
-	memset(t, 0, sizeof t);
-
-	t[0].tx_buf = command;
-	t[0].len = at25->addrlen + 1;
-	spi_message_add_tail(&t[0], &m);
-
-	t[1].rx_buf = buf;
-	t[1].len = count;
-	spi_message_add_tail(&t[1], &m);
-
-	mutex_lock(&at25->lock);
-
-	/* Read it all at once.
-	 *
-	 * REVISIT that's potentially a problem with large chips, if
-	 * other devices on the bus need to be accessed regularly or
-	 * this chip is clocked very slowly
-	 */
-	status = spi_sync(at25->spi, &m);
-	dev_dbg(&at25->spi->dev,
-		"read %Zd bytes at %d --> %d\n",
-		count, offset, (int) status);
-
-	mutex_unlock(&at25->lock);
-	return status ? status : count;
-}
-
-static ssize_t
-at25_bin_read(struct kobject *kobj, struct bin_attribute *bin_attr,
-	      char *buf, loff_t off, size_t count)
-{
-	struct device		*dev;
-	struct at25_data	*at25;
-
-	dev = container_of(kobj, struct device, kobj);
-	at25 = dev_get_drvdata(dev);
-
-	if (unlikely(off >= at25->bin.size))
-		return 0;
-	if ((off + count) > at25->bin.size)
-		count = at25->bin.size - off;
-	if (unlikely(!count))
-		return count;
-
-	return at25_ee_read(at25, buf, off, count);
-}
-
-
-static ssize_t
-at25_ee_write(struct at25_data *at25, char *buf, loff_t off, size_t count)
-{
-	ssize_t			status = 0;
-	unsigned		written = 0;
-	unsigned		buf_size;
-	u8			*bounce;
-
-	/* Temp buffer starts with command and address */
-	buf_size = at25->chip.page_size;
-	if (buf_size > io_limit)
-		buf_size = io_limit;
-	bounce = kmalloc(buf_size + at25->addrlen + 1, GFP_KERNEL);
-	if (!bounce)
-		return -ENOMEM;
-
-	/* For write, rollover is within the page ... so we write at
-	 * most one page, then manually roll over to the next page.
-	 */
-	bounce[0] = AT25_WRITE;
-	mutex_lock(&at25->lock);
-	do {
-		unsigned long	timeout, retries;
-		unsigned	segment;
-		unsigned	offset = (unsigned) off;
-		u8		*cp = bounce + 1;
-
-		*cp = AT25_WREN;
-		status = spi_write(at25->spi, cp, 1);
-		if (status < 0) {
-			dev_dbg(&at25->spi->dev, "WREN --> %d\n",
-					(int) status);
-			break;
-		}
-
-		/* 8/16/24-bit address is written MSB first */
-		switch (at25->addrlen) {
-		default:	/* case 3 */
-			*cp++ = offset >> 16;
-		case 2:
-			*cp++ = offset >> 8;
-		case 1:
-		case 0:	/* can't happen: for better codegen */
-			*cp++ = offset >> 0;
-		}
-
-		/* Write as much of a page as we can */
-		segment = buf_size - (offset % buf_size);
-		if (segment > count)
-			segment = count;
-		memcpy(cp, buf, segment);
-		status = spi_write(at25->spi, bounce,
-				segment + at25->addrlen + 1);
-		dev_dbg(&at25->spi->dev,
-				"write %u bytes at %u --> %d\n",
-				segment, offset, (int) status);
-		if (status < 0)
-			break;
-
-		/* REVISIT this should detect (or prevent) failed writes
-		 * to readonly sections of the EEPROM...
-		 */
-
-		/* Wait for non-busy status */
-		timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT);
-		retries = 0;
-		do {
-			int	sr;
-
-			sr = spi_w8r8(at25->spi, AT25_RDSR);
-			if (sr < 0 || (sr & AT25_SR_nRDY)) {
-				dev_dbg(&at25->spi->dev,
-					"rdsr --> %d (%02x)\n", sr, sr);
-				/* at HZ=100, this is sloooow */
-				msleep(1);
-				continue;
-			}
-			if (!(sr & AT25_SR_nRDY))
-				break;
-		} while (retries++ < 3 || time_before_eq(jiffies, timeout));
-
-		if (time_after(jiffies, timeout)) {
-			dev_err(&at25->spi->dev,
-				"write %d bytes offset %d, "
-				"timeout after %u msecs\n",
-				segment, offset,
-				jiffies_to_msecs(jiffies -
-					(timeout - EE_TIMEOUT)));
-			status = -ETIMEDOUT;
-			break;
-		}
-
-		off += segment;
-		buf += segment;
-		count -= segment;
-		written += segment;
-
-	} while (count > 0);
-
-	mutex_unlock(&at25->lock);
-
-	kfree(bounce);
-	return written ? written : status;
-}
-
-static ssize_t
-at25_bin_write(struct kobject *kobj, struct bin_attribute *bin_attr,
-	       char *buf, loff_t off, size_t count)
-{
-	struct device		*dev;
-	struct at25_data	*at25;
-
-	dev = container_of(kobj, struct device, kobj);
-	at25 = dev_get_drvdata(dev);
-
-	if (unlikely(off >= at25->bin.size))
-		return -EFBIG;
-	if ((off + count) > at25->bin.size)
-		count = at25->bin.size - off;
-	if (unlikely(!count))
-		return count;
-
-	return at25_ee_write(at25, buf, off, count);
-}
-
-/*-------------------------------------------------------------------------*/
-
-static int at25_probe(struct spi_device *spi)
-{
-	struct at25_data	*at25 = NULL;
-	const struct spi_eeprom *chip;
-	int			err;
-	int			sr;
-	int			addrlen;
-
-	/* Chip description */
-	chip = spi->dev.platform_data;
-	if (!chip) {
-		dev_dbg(&spi->dev, "no chip description\n");
-		err = -ENODEV;
-		goto fail;
-	}
-
-	/* For now we only support 8/16/24 bit addressing */
-	if (chip->flags & EE_ADDR1)
-		addrlen = 1;
-	else if (chip->flags & EE_ADDR2)
-		addrlen = 2;
-	else if (chip->flags & EE_ADDR3)
-		addrlen = 3;
-	else {
-		dev_dbg(&spi->dev, "unsupported address type\n");
-		err = -EINVAL;
-		goto fail;
-	}
-
-	/* Ping the chip ... the status register is pretty portable,
-	 * unlike probing manufacturer IDs.  We do expect that system
-	 * firmware didn't write it in the past few milliseconds!
-	 */
-	sr = spi_w8r8(spi, AT25_RDSR);
-	if (sr < 0 || sr & AT25_SR_nRDY) {
-		dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr);
-		err = -ENXIO;
-		goto fail;
-	}
-
-	if (!(at25 = kzalloc(sizeof *at25, GFP_KERNEL))) {
-		err = -ENOMEM;
-		goto fail;
-	}
-
-	mutex_init(&at25->lock);
-	at25->chip = *chip;
-	at25->spi = spi_dev_get(spi);
-	dev_set_drvdata(&spi->dev, at25);
-	at25->addrlen = addrlen;
-
-	/* Export the EEPROM bytes through sysfs, since that's convenient.
-	 * Default to root-only access to the data; EEPROMs often hold data
-	 * that's sensitive for read and/or write, like ethernet addresses,
-	 * security codes, board-specific manufacturing calibrations, etc.
-	 */
-	at25->bin.attr.name = "eeprom";
-	at25->bin.attr.mode = S_IRUSR;
-	at25->bin.read = at25_bin_read;
-
-	at25->bin.size = at25->chip.byte_len;
-	if (!(chip->flags & EE_READONLY)) {
-		at25->bin.write = at25_bin_write;
-		at25->bin.attr.mode |= S_IWUSR;
-	}
-
-	err = sysfs_create_bin_file(&spi->dev.kobj, &at25->bin);
-	if (err)
-		goto fail;
-
-	dev_info(&spi->dev, "%Zd %s %s eeprom%s, pagesize %u\n",
-		(at25->bin.size < 1024)
-			? at25->bin.size
-			: (at25->bin.size / 1024),
-		(at25->bin.size < 1024) ? "Byte" : "KByte",
-		at25->chip.name,
-		(chip->flags & EE_READONLY) ? " (readonly)" : "",
-		at25->chip.page_size);
-	return 0;
-fail:
-	dev_dbg(&spi->dev, "probe err %d\n", err);
-	kfree(at25);
-	return err;
-}
-
-static int __devexit at25_remove(struct spi_device *spi)
-{
-	struct at25_data	*at25;
-
-	at25 = dev_get_drvdata(&spi->dev);
-	sysfs_remove_bin_file(&spi->dev.kobj, &at25->bin);
-	kfree(at25);
-	return 0;
-}
-
-/*-------------------------------------------------------------------------*/
-
-static struct spi_driver at25_driver = {
-	.driver = {
-		.name		= "at25",
-		.owner		= THIS_MODULE,
-	},
-	.probe		= at25_probe,
-	.remove		= __devexit_p(at25_remove),
-};
-
-static int __init at25_init(void)
-{
-	return spi_register_driver(&at25_driver);
-}
-module_init(at25_init);
-
-static void __exit at25_exit(void)
-{
-	spi_unregister_driver(&at25_driver);
-}
-module_exit(at25_exit);
-
-MODULE_DESCRIPTION("Driver for most SPI EEPROMs");
-MODULE_AUTHOR("David Brownell");
-MODULE_LICENSE("GPL");
-