[SCSI] pm8001: add SAS/SATA HBA driver

This driver supports PMC-Sierra PCIe SAS/SATA 8x6G SPC 8001 chip based
host adapters.

Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

1 files changed, 888 insertions, 0 deletions

diff --git a/drivers/scsi/pm8001/pm8001_init.c b/drivers/scsi/pm8001/pm8001_init.c
new file mode 100644
index 0000000..811b5d3
--- /dev/null
+++ b/drivers/scsi/pm8001/pm8001_init.c
@@ -0,0 +1,888 @@
+/*
+ * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver
+ *
+ * Copyright (c) 2008-2009 USI Co., Ltd.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions, and the following disclaimer,
+ *    without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ *    substantially similar to the "NO WARRANTY" disclaimer below
+ *    ("Disclaimer") and any redistribution must be conditioned upon
+ *    including a substantially similar Disclaimer requirement for further
+ *    binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ *    of any contributors may be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
+ * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGES.
+ *
+ */
+
+#include "pm8001_sas.h"
+#include "pm8001_chips.h"
+
+static struct scsi_transport_template *pm8001_stt;
+
+static const struct pm8001_chip_info pm8001_chips[] = {
+	[chip_8001] = {  8, &pm8001_8001_dispatch,},
+};
+static int pm8001_id;
+
+LIST_HEAD(hba_list);
+
+/**
+ * The main structure which LLDD must register for scsi core.
+ */
+static struct scsi_host_template pm8001_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.queuecommand		= sas_queuecommand,
+	.target_alloc		= sas_target_alloc,
+	.slave_configure	= pm8001_slave_configure,
+	.slave_destroy		= sas_slave_destroy,
+	.scan_finished		= pm8001_scan_finished,
+	.scan_start		= pm8001_scan_start,
+	.change_queue_depth	= sas_change_queue_depth,
+	.change_queue_type	= sas_change_queue_type,
+	.bios_param		= sas_bios_param,
+	.can_queue		= 1,
+	.cmd_per_lun		= 1,
+	.this_id		= -1,
+	.sg_tablesize		= SG_ALL,
+	.max_sectors		= SCSI_DEFAULT_MAX_SECTORS,
+	.use_clustering		= ENABLE_CLUSTERING,
+	.eh_device_reset_handler = sas_eh_device_reset_handler,
+	.eh_bus_reset_handler	= sas_eh_bus_reset_handler,
+	.slave_alloc		= pm8001_slave_alloc,
+	.target_destroy		= sas_target_destroy,
+	.ioctl			= sas_ioctl,
+	.shost_attrs		= pm8001_host_attrs,
+};
+
+/**
+ * Sas layer call this function to execute specific task.
+ */
+static struct sas_domain_function_template pm8001_transport_ops = {
+	.lldd_dev_found		= pm8001_dev_found,
+	.lldd_dev_gone		= pm8001_dev_gone,
+
+	.lldd_execute_task	= pm8001_queue_command,
+	.lldd_control_phy	= pm8001_phy_control,
+
+	.lldd_abort_task	= pm8001_abort_task,
+	.lldd_abort_task_set	= pm8001_abort_task_set,
+	.lldd_clear_aca		= pm8001_clear_aca,
+	.lldd_clear_task_set	= pm8001_clear_task_set,
+	.lldd_I_T_nexus_reset   = pm8001_I_T_nexus_reset,
+	.lldd_lu_reset		= pm8001_lu_reset,
+	.lldd_query_task	= pm8001_query_task,
+};
+
+/**
+ *pm8001_phy_init - initiate our adapter phys
+ *@pm8001_ha: our hba structure.
+ *@phy_id: phy id.
+ */
+static void __devinit pm8001_phy_init(struct pm8001_hba_info *pm8001_ha,
+	int phy_id)
+{
+	struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
+	struct asd_sas_phy *sas_phy = &phy->sas_phy;
+	phy->phy_state = 0;
+	phy->pm8001_ha = pm8001_ha;
+	sas_phy->enabled = (phy_id < pm8001_ha->chip->n_phy) ? 1 : 0;
+	sas_phy->class = SAS;
+	sas_phy->iproto = SAS_PROTOCOL_ALL;
+	sas_phy->tproto = 0;
+	sas_phy->type = PHY_TYPE_PHYSICAL;
+	sas_phy->role = PHY_ROLE_INITIATOR;
+	sas_phy->oob_mode = OOB_NOT_CONNECTED;
+	sas_phy->linkrate = SAS_LINK_RATE_UNKNOWN;
+	sas_phy->id = phy_id;
+	sas_phy->sas_addr = &pm8001_ha->sas_addr[0];
+	sas_phy->frame_rcvd = &phy->frame_rcvd[0];
+	sas_phy->ha = (struct sas_ha_struct *)pm8001_ha->shost->hostdata;
+	sas_phy->lldd_phy = phy;
+}
+
+/**
+ *pm8001_free - free hba
+ *@pm8001_ha:	our hba structure.
+ *
+ */
+static void pm8001_free(struct pm8001_hba_info *pm8001_ha)
+{
+	int i;
+	struct pm8001_wq *wq;
+
+	if (!pm8001_ha)
+		return;
+
+	for (i = 0; i < USI_MAX_MEMCNT; i++) {
+		if (pm8001_ha->memoryMap.region[i].virt_ptr != NULL) {
+			pci_free_consistent(pm8001_ha->pdev,
+				pm8001_ha->memoryMap.region[i].element_size,
+				pm8001_ha->memoryMap.region[i].virt_ptr,
+				pm8001_ha->memoryMap.region[i].phys_addr);
+			}
+	}
+	PM8001_CHIP_DISP->chip_iounmap(pm8001_ha);
+	if (pm8001_ha->shost)
+		scsi_host_put(pm8001_ha->shost);
+	list_for_each_entry(wq, &pm8001_ha->wq_list, entry)
+		cancel_delayed_work(&wq->work_q);
+	kfree(pm8001_ha->tags);
+	kfree(pm8001_ha);
+}
+
+#ifdef PM8001_USE_TASKLET
+static void pm8001_tasklet(unsigned long opaque)
+{
+	struct pm8001_hba_info *pm8001_ha;
+	pm8001_ha = (struct pm8001_hba_info *)opaque;;
+	if (unlikely(!pm8001_ha))
+		BUG_ON(1);
+	PM8001_CHIP_DISP->isr(pm8001_ha);
+}
+#endif
+
+
+ /**
+  * pm8001_interrupt - when HBA originate a interrupt,we should invoke this
+  * dispatcher to handle each case.
+  * @irq: irq number.
+  * @opaque: the passed general host adapter struct
+  */
+static irqreturn_t pm8001_interrupt(int irq, void *opaque)
+{
+	struct pm8001_hba_info *pm8001_ha;
+	irqreturn_t ret = IRQ_HANDLED;
+	struct sas_ha_struct *sha = opaque;
+	pm8001_ha = sha->lldd_ha;
+	if (unlikely(!pm8001_ha))
+		return IRQ_NONE;
+	if (!PM8001_CHIP_DISP->is_our_interupt(pm8001_ha))
+		return IRQ_NONE;
+#ifdef PM8001_USE_TASKLET
+	tasklet_schedule(&pm8001_ha->tasklet);
+#else
+	ret = PM8001_CHIP_DISP->isr(pm8001_ha);
+#endif
+	return ret;
+}
+
+/**
+ * pm8001_alloc - initiate our hba structure and 6 DMAs area.
+ * @pm8001_ha:our hba structure.
+ *
+ */
+static int __devinit pm8001_alloc(struct pm8001_hba_info *pm8001_ha)
+{
+	int i;
+	spin_lock_init(&pm8001_ha->lock);
+	for (i = 0; i < pm8001_ha->chip->n_phy; i++)
+		pm8001_phy_init(pm8001_ha, i);
+
+	pm8001_ha->tags = kmalloc(sizeof(*pm8001_ha->tags)*PM8001_MAX_DEVICES,
+		GFP_KERNEL);
+
+	/* MPI Memory region 1 for AAP Event Log for fw */
+	pm8001_ha->memoryMap.region[AAP1].num_elements = 1;
+	pm8001_ha->memoryMap.region[AAP1].element_size = PM8001_EVENT_LOG_SIZE;
+	pm8001_ha->memoryMap.region[AAP1].total_len = PM8001_EVENT_LOG_SIZE;
+	pm8001_ha->memoryMap.region[AAP1].alignment = 32;
+
+	/* MPI Memory region 2 for IOP Event Log for fw */
+	pm8001_ha->memoryMap.region[IOP].num_elements = 1;
+	pm8001_ha->memoryMap.region[IOP].element_size = PM8001_EVENT_LOG_SIZE;
+	pm8001_ha->memoryMap.region[IOP].total_len = PM8001_EVENT_LOG_SIZE;
+	pm8001_ha->memoryMap.region[IOP].alignment = 32;
+
+	/* MPI Memory region 3 for consumer Index of inbound queues */
+	pm8001_ha->memoryMap.region[CI].num_elements = 1;
+	pm8001_ha->memoryMap.region[CI].element_size = 4;
+	pm8001_ha->memoryMap.region[CI].total_len = 4;
+	pm8001_ha->memoryMap.region[CI].alignment = 4;
+
+	/* MPI Memory region 4 for producer Index of outbound queues */
+	pm8001_ha->memoryMap.region[PI].num_elements = 1;
+	pm8001_ha->memoryMap.region[PI].element_size = 4;
+	pm8001_ha->memoryMap.region[PI].total_len = 4;
+	pm8001_ha->memoryMap.region[PI].alignment = 4;
+
+	/* MPI Memory region 5 inbound queues */
+	pm8001_ha->memoryMap.region[IB].num_elements = 256;
+	pm8001_ha->memoryMap.region[IB].element_size = 64;
+	pm8001_ha->memoryMap.region[IB].total_len = 256 * 64;
+	pm8001_ha->memoryMap.region[IB].alignment = 64;
+
+	/* MPI Memory region 6 inbound queues */
+	pm8001_ha->memoryMap.region[OB].num_elements = 256;
+	pm8001_ha->memoryMap.region[OB].element_size = 64;
+	pm8001_ha->memoryMap.region[OB].total_len = 256 * 64;
+	pm8001_ha->memoryMap.region[OB].alignment = 64;
+
+	/* Memory region write DMA*/
+	pm8001_ha->memoryMap.region[NVMD].num_elements = 1;
+	pm8001_ha->memoryMap.region[NVMD].element_size = 4096;
+	pm8001_ha->memoryMap.region[NVMD].total_len = 4096;
+	/* Memory region for devices*/
+	pm8001_ha->memoryMap.region[DEV_MEM].num_elements = 1;
+	pm8001_ha->memoryMap.region[DEV_MEM].element_size = PM8001_MAX_DEVICES *
+		sizeof(struct pm8001_device);
+	pm8001_ha->memoryMap.region[DEV_MEM].total_len = PM8001_MAX_DEVICES *
+		sizeof(struct pm8001_device);
+
+	/* Memory region for ccb_info*/
+	pm8001_ha->memoryMap.region[CCB_MEM].num_elements = 1;
+	pm8001_ha->memoryMap.region[CCB_MEM].element_size = PM8001_MAX_CCB *
+		sizeof(struct pm8001_ccb_info);
+	pm8001_ha->memoryMap.region[CCB_MEM].total_len = PM8001_MAX_CCB *
+		sizeof(struct pm8001_ccb_info);
+
+	for (i = 0; i < USI_MAX_MEMCNT; i++) {
+		if (pm8001_mem_alloc(pm8001_ha->pdev,
+			&pm8001_ha->memoryMap.region[i].virt_ptr,
+			&pm8001_ha->memoryMap.region[i].phys_addr,
+			&pm8001_ha->memoryMap.region[i].phys_addr_hi,
+			&pm8001_ha->memoryMap.region[i].phys_addr_lo,
+			pm8001_ha->memoryMap.region[i].total_len,
+			pm8001_ha->memoryMap.region[i].alignment) != 0) {
+				PM8001_FAIL_DBG(pm8001_ha,
+					pm8001_printk("Mem%d alloc failed\n",
+					i));
+				goto err_out;
+		}
+	}
+
+	pm8001_ha->devices = pm8001_ha->memoryMap.region[DEV_MEM].virt_ptr;
+	for (i = 0; i < PM8001_MAX_DEVICES; i++) {
+		pm8001_ha->devices[i].dev_type = NO_DEVICE;
+		pm8001_ha->devices[i].id = i;
+		pm8001_ha->devices[i].device_id = PM8001_MAX_DEVICES;
+		pm8001_ha->devices[i].running_req = 0;
+	}
+	pm8001_ha->ccb_info = pm8001_ha->memoryMap.region[CCB_MEM].virt_ptr;
+	for (i = 0; i < PM8001_MAX_CCB; i++) {
+		pm8001_ha->ccb_info[i].ccb_dma_handle =
+			pm8001_ha->memoryMap.region[CCB_MEM].phys_addr +
+			i * sizeof(struct pm8001_ccb_info);
+		++pm8001_ha->tags_num;
+	}
+	pm8001_ha->flags = PM8001F_INIT_TIME;
+	/* Initialize tags */
+	pm8001_tag_init(pm8001_ha);
+	return 0;
+err_out:
+	return 1;
+}
+
+/**
+ * pm8001_ioremap - remap the pci high physical address to kernal virtual
+ * address so that we can access them.
+ * @pm8001_ha:our hba structure.
+ */
+static int pm8001_ioremap(struct pm8001_hba_info *pm8001_ha)
+{
+	u32 bar;
+	u32 logicalBar = 0;
+	struct pci_dev *pdev;
+
+	pdev = pm8001_ha->pdev;
+	/* map pci mem (PMC pci base 0-3)*/
+	for (bar = 0; bar < 6; bar++) {
+		/*
+		** logical BARs for SPC:
+		** bar 0 and 1 - logical BAR0
+		** bar 2 and 3 - logical BAR1
+		** bar4 - logical BAR2
+		** bar5 - logical BAR3
+		** Skip the appropriate assignments:
+		*/
+		if ((bar == 1) || (bar == 3))
+			continue;
+		if (pci_resource_flags(pdev, bar) & IORESOURCE_MEM) {
+			pm8001_ha->io_mem[logicalBar].membase =
+				pci_resource_start(pdev, bar);
+			pm8001_ha->io_mem[logicalBar].membase &=
+				(u32)PCI_BASE_ADDRESS_MEM_MASK;
+			pm8001_ha->io_mem[logicalBar].memsize =
+				pci_resource_len(pdev, bar);
+			pm8001_ha->io_mem[logicalBar].memvirtaddr =
+				ioremap(pm8001_ha->io_mem[logicalBar].membase,
+				pm8001_ha->io_mem[logicalBar].memsize);
+			PM8001_INIT_DBG(pm8001_ha,
+				pm8001_printk("PCI: bar %d, logicalBar %d "
+				"virt_addr=%lx,len=%d\n", bar, logicalBar,
+				(unsigned long)
+				pm8001_ha->io_mem[logicalBar].memvirtaddr,
+				pm8001_ha->io_mem[logicalBar].memsize));
+		} else {
+			pm8001_ha->io_mem[logicalBar].membase	= 0;
+			pm8001_ha->io_mem[logicalBar].memsize	= 0;
+			pm8001_ha->io_mem[logicalBar].memvirtaddr = 0;
+		}
+		logicalBar++;
+	}
+	return 0;
+}
+
+/**
+ * pm8001_pci_alloc - initialize our ha card structure
+ * @pdev: pci device.
+ * @ent: ent
+ * @shost: scsi host struct which has been initialized before.
+ */
+static struct pm8001_hba_info *__devinit
+pm8001_pci_alloc(struct pci_dev *pdev, u32 chip_id, struct Scsi_Host *shost)
+{
+	struct pm8001_hba_info *pm8001_ha;
+	struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
+
+
+	pm8001_ha = sha->lldd_ha;
+	if (!pm8001_ha)
+		return NULL;
+
+	pm8001_ha->pdev = pdev;
+	pm8001_ha->dev = &pdev->dev;
+	pm8001_ha->chip_id = chip_id;
+	pm8001_ha->chip = &pm8001_chips[pm8001_ha->chip_id];
+	pm8001_ha->irq = pdev->irq;
+	pm8001_ha->sas = sha;
+	pm8001_ha->shost = shost;
+	pm8001_ha->id = pm8001_id++;
+	INIT_LIST_HEAD(&pm8001_ha->wq_list);
+	pm8001_ha->logging_level = 0x01;
+	sprintf(pm8001_ha->name, "%s%d", DRV_NAME, pm8001_ha->id);
+#ifdef PM8001_USE_TASKLET
+	tasklet_init(&pm8001_ha->tasklet, pm8001_tasklet,
+		(unsigned long)pm8001_ha);
+#endif
+	pm8001_ioremap(pm8001_ha);
+	if (!pm8001_alloc(pm8001_ha))
+		return pm8001_ha;
+	pm8001_free(pm8001_ha);
+	return NULL;
+}
+
+/**
+ * pci_go_44 - pm8001 specified, its DMA is 44 bit rather than 64 bit
+ * @pdev: pci device.
+ */
+static int pci_go_44(struct pci_dev *pdev)
+{
+	int rc;
+
+	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(44))) {
+		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(44));
+		if (rc) {
+			rc = pci_set_consistent_dma_mask(pdev,
+				DMA_BIT_MASK(32));
+			if (rc) {
+				dev_printk(KERN_ERR, &pdev->dev,
+					"44-bit DMA enable failed\n");
+				return rc;
+			}
+		}
+	} else {
+		rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+		if (rc) {
+			dev_printk(KERN_ERR, &pdev->dev,
+				"32-bit DMA enable failed\n");
+			return rc;
+		}
+		rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+		if (rc) {
+			dev_printk(KERN_ERR, &pdev->dev,
+				"32-bit consistent DMA enable failed\n");
+			return rc;
+		}
+	}
+	return rc;
+}
+
+/**
+ * pm8001_prep_sas_ha_init - allocate memory in general hba struct && init them.
+ * @shost: scsi host which has been allocated outside.
+ * @chip_info: our ha struct.
+ */
+static int __devinit pm8001_prep_sas_ha_init(struct Scsi_Host * shost,
+	const struct pm8001_chip_info *chip_info)
+{
+	int phy_nr, port_nr;
+	struct asd_sas_phy **arr_phy;
+	struct asd_sas_port **arr_port;
+	struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
+
+	phy_nr = chip_info->n_phy;
+	port_nr = phy_nr;
+	memset(sha, 0x00, sizeof(*sha));
+	arr_phy = kcalloc(phy_nr, sizeof(void *), GFP_KERNEL);
+	if (!arr_phy)
+		goto exit;
+	arr_port = kcalloc(port_nr, sizeof(void *), GFP_KERNEL);
+	if (!arr_port)
+		goto exit_free2;
+
+	sha->sas_phy = arr_phy;
+	sha->sas_port = arr_port;
+	sha->lldd_ha = kzalloc(sizeof(struct pm8001_hba_info), GFP_KERNEL);
+	if (!sha->lldd_ha)
+		goto exit_free1;
+
+	shost->transportt = pm8001_stt;
+	shost->max_id = PM8001_MAX_DEVICES;
+	shost->max_lun = 8;
+	shost->max_channel = 0;
+	shost->unique_id = pm8001_id;
+	shost->max_cmd_len = 16;
+	shost->can_queue = PM8001_CAN_QUEUE;
+	shost->cmd_per_lun = 32;
+	return 0;
+exit_free1:
+	kfree(arr_port);
+exit_free2:
+	kfree(arr_phy);
+exit:
+	return -1;
+}
+
+/**
+ * pm8001_post_sas_ha_init - initialize general hba struct defined in libsas
+ * @shost: scsi host which has been allocated outside
+ * @chip_info: our ha struct.
+ */
+static void  __devinit pm8001_post_sas_ha_init(struct Scsi_Host *shost,
+	const struct pm8001_chip_info *chip_info)
+{
+	int i = 0;
+	struct pm8001_hba_info *pm8001_ha;
+	struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
+
+	pm8001_ha = sha->lldd_ha;
+	for (i = 0; i < chip_info->n_phy; i++) {
+		sha->sas_phy[i] = &pm8001_ha->phy[i].sas_phy;
+		sha->sas_port[i] = &pm8001_ha->port[i].sas_port;
+	}
+	sha->sas_ha_name = DRV_NAME;
+	sha->dev = pm8001_ha->dev;
+
+	sha->lldd_module = THIS_MODULE;
+	sha->sas_addr = &pm8001_ha->sas_addr[0];
+	sha->num_phys = chip_info->n_phy;
+	sha->lldd_max_execute_num = 1;
+	sha->lldd_queue_size = PM8001_CAN_QUEUE;
+	sha->core.shost = shost;
+}
+
+/**
+ * pm8001_init_sas_add - initialize sas address
+ * @chip_info: our ha struct.
+ *
+ * Currently we just set the fixed SAS address to our HBA,for manufacture,
+ * it should read from the EEPROM
+ */
+static void pm8001_init_sas_add(struct pm8001_hba_info *pm8001_ha)
+{
+	u8 i;
+#ifdef PM8001_READ_VPD
+	DECLARE_COMPLETION_ONSTACK(completion);
+	pm8001_ha->nvmd_completion = &completion;
+	PM8001_CHIP_DISP->get_nvmd_req(pm8001_ha, 0, 0);
+	wait_for_completion(&completion);
+	for (i = 0; i < pm8001_ha->chip->n_phy; i++) {
+		memcpy(&pm8001_ha->phy[i].dev_sas_addr, pm8001_ha->sas_addr,
+			SAS_ADDR_SIZE);
+		PM8001_INIT_DBG(pm8001_ha,
+			pm8001_printk("phy %d sas_addr = %x \n", i,
+			(u64)pm8001_ha->phy[i].dev_sas_addr));
+	}
+#else
+	for (i = 0; i < pm8001_ha->chip->n_phy; i++) {
+		pm8001_ha->phy[i].dev_sas_addr = 0x500e004010000004ULL;
+		pm8001_ha->phy[i].dev_sas_addr =
+			cpu_to_be64((u64)
+				(*(u64 *)&pm8001_ha->phy[i].dev_sas_addr));
+	}
+	memcpy(pm8001_ha->sas_addr, &pm8001_ha->phy[0].dev_sas_addr,
+		SAS_ADDR_SIZE);
+#endif
+}
+
+#ifdef PM8001_USE_MSIX
+/**
+ * pm8001_setup_msix - enable MSI-X interrupt
+ * @chip_info: our ha struct.
+ * @irq_handler: irq_handler
+ */
+static u32 pm8001_setup_msix(struct pm8001_hba_info *pm8001_ha,
+	irq_handler_t irq_handler)
+{
+	u32 i = 0, j = 0;
+	u32 number_of_intr = 1;
+	int flag = 0;
+	u32 max_entry;
+	int rc;
+	max_entry = sizeof(pm8001_ha->msix_entries) /
+		sizeof(pm8001_ha->msix_entries[0]);
+	flag |= IRQF_DISABLED;
+	for (i = 0; i < max_entry ; i++)
+		pm8001_ha->msix_entries[i].entry = i;
+	rc = pci_enable_msix(pm8001_ha->pdev, pm8001_ha->msix_entries,
+		number_of_intr);
+	pm8001_ha->number_of_intr = number_of_intr;
+	if (!rc) {
+		for (i = 0; i < number_of_intr; i++) {
+			if (request_irq(pm8001_ha->msix_entries[i].vector,
+				irq_handler, flag, DRV_NAME,
+				SHOST_TO_SAS_HA(pm8001_ha->shost))) {
+				for (j = 0; j < i; j++)
+					free_irq(
+					pm8001_ha->msix_entries[j].vector,
+					SHOST_TO_SAS_HA(pm8001_ha->shost));
+				pci_disable_msix(pm8001_ha->pdev);
+				break;
+			}
+		}
+	}
+	return rc;
+}
+#endif
+
+/**
+ * pm8001_request_irq - register interrupt
+ * @chip_info: our ha struct.
+ */
+static u32 pm8001_request_irq(struct pm8001_hba_info *pm8001_ha)
+{
+	struct pci_dev *pdev;
+	irq_handler_t irq_handler = pm8001_interrupt;
+	u32 rc;
+
+	pdev = pm8001_ha->pdev;
+
+#ifdef PM8001_USE_MSIX
+	if (pci_find_capability(pdev, PCI_CAP_ID_MSIX))
+		return pm8001_setup_msix(pm8001_ha, irq_handler);
+	else
+		goto intx;
+#endif
+
+intx:
+	/* intialize the INT-X interrupt */
+	rc = request_irq(pdev->irq, irq_handler, IRQF_SHARED, DRV_NAME,
+		SHOST_TO_SAS_HA(pm8001_ha->shost));
+	return rc;
+}
+
+/**
+ * pm8001_pci_probe - probe supported device
+ * @pdev: pci device which kernel has been prepared for.
+ * @ent: pci device id
+ *
+ * This function is the main initialization function, when register a new
+ * pci driver it is invoked, all struct an hardware initilization should be done
+ * here, also, register interrupt
+ */
+static int __devinit pm8001_pci_probe(struct pci_dev *pdev,
+	const struct pci_device_id *ent)
+{
+	unsigned int rc;
+	u32	pci_reg;
+	struct pm8001_hba_info *pm8001_ha;
+	struct Scsi_Host *shost = NULL;
+	const struct pm8001_chip_info *chip;
+
+	dev_printk(KERN_INFO, &pdev->dev,
+		"pm8001: driver version %s\n", DRV_VERSION);
+	rc = pci_enable_device(pdev);
+	if (rc)
+		goto err_out_enable;
+	pci_set_master(pdev);
+	/*
+	 * Enable pci slot busmaster by setting pci command register.
+	 * This is required by FW for Cyclone card.
+	 */
+
+	pci_read_config_dword(pdev, PCI_COMMAND, &pci_reg);
+	pci_reg |= 0x157;
+	pci_write_config_dword(pdev, PCI_COMMAND, pci_reg);
+	rc = pci_request_regions(pdev, DRV_NAME);
+	if (rc)
+		goto err_out_disable;
+	rc = pci_go_44(pdev);
+	if (rc)
+		goto err_out_regions;
+
+	shost = scsi_host_alloc(&pm8001_sht, sizeof(void *));
+	if (!shost) {
+		rc = -ENOMEM;
+		goto err_out_regions;
+	}
+	chip = &pm8001_chips[ent->driver_data];
+	SHOST_TO_SAS_HA(shost) =
+		kcalloc(1, sizeof(struct sas_ha_struct), GFP_KERNEL);
+	if (!SHOST_TO_SAS_HA(shost)) {
+		rc = -ENOMEM;
+		goto err_out_free_host;
+	}
+
+	rc = pm8001_prep_sas_ha_init(shost, chip);
+	if (rc) {
+		rc = -ENOMEM;
+		goto err_out_free;
+	}
+	pci_set_drvdata(pdev, SHOST_TO_SAS_HA(shost));
+	pm8001_ha = pm8001_pci_alloc(pdev, chip_8001, shost);
+	if (!pm8001_ha) {
+		rc = -ENOMEM;
+		goto err_out_free;
+	}
+	list_add_tail(&pm8001_ha->list, &hba_list);
+	PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd);
+	rc = PM8001_CHIP_DISP->chip_init(pm8001_ha);
+	if (rc)
+		goto err_out_ha_free;
+
+	rc = scsi_add_host(shost, &pdev->dev);
+	if (rc)
+		goto err_out_ha_free;
+	rc = pm8001_request_irq(pm8001_ha);
+	if (rc)
+		goto err_out_shost;
+
+	PM8001_CHIP_DISP->interrupt_enable(pm8001_ha);
+	pm8001_init_sas_add(pm8001_ha);
+	pm8001_post_sas_ha_init(shost, chip);
+	rc = sas_register_ha(SHOST_TO_SAS_HA(shost));
+	if (rc)
+		goto err_out_shost;
+	scsi_scan_host(pm8001_ha->shost);
+	return 0;
+
+err_out_shost:
+	scsi_remove_host(pm8001_ha->shost);
+err_out_ha_free:
+	pm8001_free(pm8001_ha);
+err_out_free:
+	kfree(SHOST_TO_SAS_HA(shost));
+err_out_free_host:
+	kfree(shost);
+err_out_regions:
+	pci_release_regions(pdev);
+err_out_disable:
+	pci_disable_device(pdev);
+err_out_enable:
+	return rc;
+}
+
+static void __devexit pm8001_pci_remove(struct pci_dev *pdev)
+{
+	struct sas_ha_struct *sha = pci_get_drvdata(pdev);
+	struct pm8001_hba_info *pm8001_ha;
+	int i;
+	pm8001_ha = sha->lldd_ha;
+	pci_set_drvdata(pdev, NULL);
+	sas_unregister_ha(sha);
+	sas_remove_host(pm8001_ha->shost);
+	list_del(&pm8001_ha->list);
+	scsi_remove_host(pm8001_ha->shost);
+	PM8001_CHIP_DISP->interrupt_disable(pm8001_ha);
+	PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd);
+
+#ifdef PM8001_USE_MSIX
+	for (i = 0; i < pm8001_ha->number_of_intr; i++)
+		synchronize_irq(pm8001_ha->msix_entries[i].vector);
+	for (i = 0; i < pm8001_ha->number_of_intr; i++)
+		free_irq(pm8001_ha->msix_entries[i].vector, sha);
+	pci_disable_msix(pdev);
+#else
+	free_irq(pm8001_ha->irq, sha);
+#endif
+#ifdef PM8001_USE_TASKLET
+	tasklet_kill(&pm8001_ha->tasklet);
+#endif
+	pm8001_free(pm8001_ha);
+	kfree(sha->sas_phy);
+	kfree(sha->sas_port);
+	kfree(sha);
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
+}
+
+/**
+ * pm8001_pci_suspend - power management suspend main entry point
+ * @pdev: PCI device struct
+ * @state: PM state change to (usually PCI_D3)
+ *
+ * Returns 0 success, anything else error.
+ */
+static int pm8001_pci_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct sas_ha_struct *sha = pci_get_drvdata(pdev);
+	struct pm8001_hba_info *pm8001_ha;
+	int i , pos;
+	u32 device_state;
+	pm8001_ha = sha->lldd_ha;
+	flush_scheduled_work();
+	scsi_block_requests(pm8001_ha->shost);
+	pos = pci_find_capability(pdev, PCI_CAP_ID_PM);
+	if (pos == 0) {
+		printk(KERN_ERR " PCI PM not supported\n");
+		return -ENODEV;
+	}
+	PM8001_CHIP_DISP->interrupt_disable(pm8001_ha);
+	PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd);
+#ifdef PM8001_USE_MSIX
+	for (i = 0; i < pm8001_ha->number_of_intr; i++)
+		synchronize_irq(pm8001_ha->msix_entries[i].vector);
+	for (i = 0; i < pm8001_ha->number_of_intr; i++)
+		free_irq(pm8001_ha->msix_entries[i].vector, sha);
+	pci_disable_msix(pdev);
+#else
+	free_irq(pm8001_ha->irq, sha);
+#endif
+#ifdef PM8001_USE_TASKLET
+	tasklet_kill(&pm8001_ha->tasklet);
+#endif
+	device_state = pci_choose_state(pdev, state);
+	pm8001_printk("pdev=0x%p, slot=%s, entering "
+		      "operating state [D%d]\n", pdev,
+		      pm8001_ha->name, device_state);
+	pci_save_state(pdev);
+	pci_disable_device(pdev);
+	pci_set_power_state(pdev, device_state);
+	return 0;
+}
+
+/**
+ * pm8001_pci_resume - power management resume main entry point
+ * @pdev: PCI device struct
+ *
+ * Returns 0 success, anything else error.
+ */
+static int pm8001_pci_resume(struct pci_dev *pdev)
+{
+	struct sas_ha_struct *sha = pci_get_drvdata(pdev);
+	struct pm8001_hba_info *pm8001_ha;
+	int rc;
+	u32 device_state;
+	pm8001_ha = sha->lldd_ha;
+	device_state = pdev->current_state;
+
+	pm8001_printk("pdev=0x%p, slot=%s, resuming from previous "
+		"operating state [D%d]\n", pdev, pm8001_ha->name, device_state);
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_enable_wake(pdev, PCI_D0, 0);
+	pci_restore_state(pdev);
+	rc = pci_enable_device(pdev);
+	if (rc) {
+		pm8001_printk("slot=%s Enable device failed during resume\n",
+			      pm8001_ha->name);
+		goto err_out_enable;
+	}
+
+	pci_set_master(pdev);
+	rc = pci_go_44(pdev);
+	if (rc)
+		goto err_out_disable;
+
+	PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd);
+	rc = PM8001_CHIP_DISP->chip_init(pm8001_ha);
+	if (rc)
+		goto err_out_disable;
+	PM8001_CHIP_DISP->interrupt_disable(pm8001_ha);
+	rc = pm8001_request_irq(pm8001_ha);
+	if (rc)
+		goto err_out_disable;
+	#ifdef PM8001_USE_TASKLET
+	tasklet_init(&pm8001_ha->tasklet, pm8001_tasklet,
+		    (unsigned long)pm8001_ha);
+	#endif
+	PM8001_CHIP_DISP->interrupt_enable(pm8001_ha);
+	scsi_unblock_requests(pm8001_ha->shost);
+	return 0;
+
+err_out_disable:
+	scsi_remove_host(pm8001_ha->shost);
+	pci_disable_device(pdev);
+err_out_enable:
+	return rc;
+}
+
+static struct pci_device_id __devinitdata pm8001_pci_table[] = {
+	{
+		PCI_VDEVICE(PMC_Sierra, 0x8001), chip_8001
+	},
+	{
+		PCI_DEVICE(0x117c, 0x0042),
+		.driver_data = chip_8001
+	},
+	{} /* terminate list */
+};
+
+static struct pci_driver pm8001_pci_driver = {
+	.name		= DRV_NAME,
+	.id_table	= pm8001_pci_table,
+	.probe		= pm8001_pci_probe,
+	.remove		= __devexit_p(pm8001_pci_remove),
+	.suspend	= pm8001_pci_suspend,
+	.resume		= pm8001_pci_resume,
+};
+
+/**
+ *	pm8001_init - initialize scsi transport template
+ */
+static int __init pm8001_init(void)
+{
+	int rc;
+	pm8001_id = 0;
+	pm8001_stt = sas_domain_attach_transport(&pm8001_transport_ops);
+	if (!pm8001_stt)
+		return -ENOMEM;
+	rc = pci_register_driver(&pm8001_pci_driver);
+	if (rc)
+		goto err_out;
+	return 0;
+err_out:
+	sas_release_transport(pm8001_stt);
+	return rc;
+}
+
+static void __exit pm8001_exit(void)
+{
+	pci_unregister_driver(&pm8001_pci_driver);
+	sas_release_transport(pm8001_stt);
+}
+
+module_init(pm8001_init);
+module_exit(pm8001_exit);
+
+MODULE_AUTHOR("Jack Wang <jack_wang@usish.com>");
+MODULE_DESCRIPTION("PMC-Sierra PM8001 SAS/SATA controller driver");
+MODULE_VERSION(DRV_VERSION);
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, pm8001_pci_table);
+