Merge tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "Quite a lot of core work this time around, though not 100% successful.

  We gained support for runtime mode changes thanks to David Collins and
  improved support for write only regulators (ones where we can't read
  back the configuration) from Douglas Anderson.

  There's been quite a bit of work from Linus Walleij on converting from
  specfying GPIOs by numbers to descriptors. Sadly the testing turned
  out to be less good than we had hoped and so a lot of this had to be
  reverted.

  We also have the start of updates to use coupled regulators from
  Maciej Purski, unfortunately there are further problems there so the
  last couple of patches have been reverted.

  We also have new drivers for BD71837 and SY8106A devices, SAW
  regulators on Qualcomm SPMI and dropped support for some preproduction
  chips that never made it to market from the AB8500 driver"

* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
  regulator: gpio: Revert
  ARM: pxa, regulator: fix building ezx e680
  regulator: Revert coupled regulator support again
  regulator: wm8994: Fix shared GPIOs
  regulator: max77686: Fix shared GPIOs
  regulator: bd71837: BD71837 PMIC regulator driver
  regulator: bd71837: Devicetree bindings for BD71837 regulators
  regulator: gpio: Get enable GPIO using GPIO descriptor
  regulator: fixed: Convert to use GPIO descriptor only
  regulator: s2mps11: Fix boot on Odroid XU3
  dt-bindings: qcom_spmi: Document SAW support
  regulator: qcom_spmi: Add support for SAW
  regulator: tps65090: Pass descriptor instead of GPIO number
  regulator: s5m8767: Pass descriptor instead of GPIO number
  regulator: pfuze100: Delete reference to ena_gpio
  regulator: max8952: Pass descriptor instead of GPIO number
  regulator: lp8788-ldo: Pass descriptor instead of GPIO number
  regulator: lm363x: Pass descriptor instead of GPIO number
  regulator: max8973: Pass descriptor instead of GPIO number
  regulator: mc13xxx-core: Switch to SPDX identifier
  ...

1 files changed, 130 insertions, 3 deletions

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 63c7a0c..9817f1a 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -25,6 +25,8 @@
 #include <linux/regulator/driver.h>
 #include <linux/regmap.h>
 #include <linux/list.h>
+#include <linux/mfd/syscon.h>
+#include <linux/io.h>
 
 /* Pin control enable input pins. */
 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_NONE		0x00
@@ -181,6 +183,23 @@ enum spmi_boost_byp_registers {
 	SPMI_BOOST_BYP_REG_CURRENT_LIMIT	= 0x4b,
 };
 
+enum spmi_saw3_registers {
+	SAW3_SECURE				= 0x00,
+	SAW3_ID					= 0x04,
+	SAW3_SPM_STS				= 0x0C,
+	SAW3_AVS_STS				= 0x10,
+	SAW3_PMIC_STS				= 0x14,
+	SAW3_RST				= 0x18,
+	SAW3_VCTL				= 0x1C,
+	SAW3_AVS_CTL				= 0x20,
+	SAW3_AVS_LIMIT				= 0x24,
+	SAW3_AVS_DLY				= 0x28,
+	SAW3_AVS_HYSTERESIS			= 0x2C,
+	SAW3_SPM_STS2				= 0x38,
+	SAW3_SPM_PMIC_DATA_3			= 0x4C,
+	SAW3_VERSION				= 0xFD0,
+};
+
 /* Used for indexing into ctrl_reg.  These are offets from 0x40 */
 enum spmi_common_control_register_index {
 	SPMI_COMMON_IDX_VOLTAGE_RANGE		= 0,
@@ -1035,6 +1054,89 @@ static irqreturn_t spmi_regulator_vs_ocp_isr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+#define SAW3_VCTL_DATA_MASK	0xFF
+#define SAW3_VCTL_CLEAR_MASK	0x700FF
+#define SAW3_AVS_CTL_EN_MASK	0x1
+#define SAW3_AVS_CTL_TGGL_MASK	0x8000000
+#define SAW3_AVS_CTL_CLEAR_MASK	0x7efc00
+
+static struct regmap *saw_regmap = NULL;
+
+static void spmi_saw_set_vdd(void *data)
+{
+	u32 vctl, data3, avs_ctl, pmic_sts;
+	bool avs_enabled = false;
+	unsigned long timeout;
+	u8 voltage_sel = *(u8 *)data;
+
+	regmap_read(saw_regmap, SAW3_AVS_CTL, &avs_ctl);
+	regmap_read(saw_regmap, SAW3_VCTL, &vctl);
+	regmap_read(saw_regmap, SAW3_SPM_PMIC_DATA_3, &data3);
+
+	/* select the band */
+	vctl &= ~SAW3_VCTL_CLEAR_MASK;
+	vctl |= (u32)voltage_sel;
+
+	data3 &= ~SAW3_VCTL_CLEAR_MASK;
+	data3 |= (u32)voltage_sel;
+
+	/* If AVS is enabled, switch it off during the voltage change */
+	avs_enabled = SAW3_AVS_CTL_EN_MASK & avs_ctl;
+	if (avs_enabled) {
+		avs_ctl &= ~SAW3_AVS_CTL_TGGL_MASK;
+		regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
+	}
+
+	regmap_write(saw_regmap, SAW3_RST, 1);
+	regmap_write(saw_regmap, SAW3_VCTL, vctl);
+	regmap_write(saw_regmap, SAW3_SPM_PMIC_DATA_3, data3);
+
+	timeout = jiffies + usecs_to_jiffies(100);
+	do {
+		regmap_read(saw_regmap, SAW3_PMIC_STS, &pmic_sts);
+		pmic_sts &= SAW3_VCTL_DATA_MASK;
+		if (pmic_sts == (u32)voltage_sel)
+			break;
+
+		cpu_relax();
+
+	} while (time_before(jiffies, timeout));
+
+	/* After successful voltage change, switch the AVS back on */
+	if (avs_enabled) {
+		pmic_sts &= 0x3f;
+		avs_ctl &= ~SAW3_AVS_CTL_CLEAR_MASK;
+		avs_ctl |= ((pmic_sts - 4) << 10);
+		avs_ctl |= (pmic_sts << 17);
+		avs_ctl |= SAW3_AVS_CTL_TGGL_MASK;
+		regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
+	}
+}
+
+static int
+spmi_regulator_saw_set_voltage(struct regulator_dev *rdev, unsigned selector)
+{
+	struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+	int ret;
+	u8 range_sel, voltage_sel;
+
+	ret = spmi_sw_selector_to_hw(vreg, selector, &range_sel, &voltage_sel);
+	if (ret)
+		return ret;
+
+	if (0 != range_sel) {
+		dev_dbg(&rdev->dev, "range_sel = %02X voltage_sel = %02X", \
+			range_sel, voltage_sel);
+		return -EINVAL;
+	}
+
+	/* Always do the SAW register writes on the first CPU */
+	return smp_call_function_single(0, spmi_saw_set_vdd, \
+					&voltage_sel, true);
+}
+
+static struct regulator_ops spmi_saw_ops = {};
+
 static struct regulator_ops spmi_smps_ops = {
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
@@ -1250,6 +1352,7 @@ static int spmi_regulator_match(struct spmi_regulator *vreg, u16 force_type)
 	}
 	dig_major_rev	= version[SPMI_COMMON_REG_DIG_MAJOR_REV
 					- SPMI_COMMON_REG_DIG_MAJOR_REV];
+
 	if (!force_type) {
 		type		= version[SPMI_COMMON_REG_TYPE -
 					  SPMI_COMMON_REG_DIG_MAJOR_REV];
@@ -1648,7 +1751,9 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 	struct regmap *regmap;
 	const char *name;
 	struct device *dev = &pdev->dev;
-	int ret;
+	struct device_node *node = pdev->dev.of_node;
+	struct device_node *syscon;
+	int ret, lenp;
 	struct list_head *vreg_list;
 
 	vreg_list = devm_kzalloc(dev, sizeof(*vreg_list), GFP_KERNEL);
@@ -1665,7 +1770,22 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 	if (!match)
 		return -ENODEV;
 
+	if (of_find_property(node, "qcom,saw-reg", &lenp)) {
+		syscon = of_parse_phandle(node, "qcom,saw-reg", 0);
+		saw_regmap = syscon_node_to_regmap(syscon);
+		of_node_put(syscon);
+		if (IS_ERR(regmap))
+			dev_err(dev, "ERROR reading SAW regmap\n");
+	}
+
 	for (reg = match->data; reg->name; reg++) {
+
+		if (saw_regmap && \
+		    of_find_property(of_find_node_by_name(node, reg->name), \
+				     "qcom,saw-slave", &lenp)) {
+			continue;
+		}
+
 		vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL);
 		if (!vreg)
 			return -ENOMEM;
@@ -1673,7 +1793,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 		vreg->dev = dev;
 		vreg->base = reg->base;
 		vreg->regmap = regmap;
-
 		if (reg->ocp) {
 			vreg->ocp_irq = platform_get_irq_byname(pdev, reg->ocp);
 			if (vreg->ocp_irq < 0) {
@@ -1681,7 +1800,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 				goto err;
 			}
 		}
-
 		vreg->desc.id = -1;
 		vreg->desc.owner = THIS_MODULE;
 		vreg->desc.type = REGULATOR_VOLTAGE;
@@ -1698,6 +1816,15 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
 		if (ret)
 			continue;
 
+		if (saw_regmap && \
+		    of_find_property(of_find_node_by_name(node, reg->name), \
+				     "qcom,saw-leader", &lenp)) {
+			spmi_saw_ops = *(vreg->desc.ops);
+			spmi_saw_ops.set_voltage_sel = \
+				spmi_regulator_saw_set_voltage;
+			vreg->desc.ops = &spmi_saw_ops;
+		}
+
 		config.dev = dev;
 		config.driver_data = vreg;
 		config.regmap = regmap;