diff options
| author | Alan Cox <alan@lxorguk.ukuu.org.uk> | 2006-07-12 15:05:41 +0100 |
|---|---|---|
| committer | Linus Torvalds <torvalds@g5.osdl.org> | 2006-07-12 12:59:35 -0700 |
| commit | 15e0c694367332d7e7114c7c73044bc5fed9ee48 (patch) | |
| tree | de18bd97c7438f44fac3b28ea5447f4aa9fcf98e /drivers/pci | |
| parent | f6dc8c5b8e04ce28720155383e971561a23899d5 (diff) | |
| download | op-kernel-dev-15e0c694367332d7e7114c7c73044bc5fed9ee48.zip op-kernel-dev-15e0c694367332d7e7114c7c73044bc5fed9ee48.tar.gz | |
[PATCH] ide: fix Jmicron support
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Diffstat (limited to 'drivers/pci')
| -rw-r--r-- | drivers/pci/quirks.c | 49 |
1 files changed, 49 insertions, 0 deletions
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index e9a57af..de3bbc8 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -1175,6 +1175,55 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus ); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus ); +#if defined(CONFIG_SCSI_SATA) || defined(CONFIG_SCSI_SATA_MODULE) + +/* + * If we are using libata we can drive this chip properly but must + * do this early on to make the additional device appear during + * the PCI scanning. + */ + +static void __devinit quirk_jmicron_dualfn(struct pci_dev *pdev) +{ + u32 conf; + u8 hdr; + + /* Only poke fn 0 */ + if (PCI_FUNC(pdev->devfn)) + return; + + switch(pdev->device) { + case PCI_DEVICE_ID_JMICRON_JMB365: + case PCI_DEVICE_ID_JMICRON_JMB366: + /* Redirect IDE second PATA port to the right spot */ + pci_read_config_dword(pdev, 0x80, &conf); + conf |= (1 << 24); + /* Fall through */ + pci_write_config_dword(pdev, 0x80, conf); + case PCI_DEVICE_ID_JMICRON_JMB361: + case PCI_DEVICE_ID_JMICRON_JMB363: + pci_read_config_dword(pdev, 0x40, &conf); + /* Enable dual function mode, AHCI on fn 0, IDE fn1 */ + /* Set the class codes correctly and then direct IDE 0 */ + conf &= ~0x000F0200; /* Clear bit 9 and 16-19 */ + conf |= 0x00C20002; /* Set bit 1, 17, 22, 23 */ + pci_write_config_dword(pdev, 0x40, conf); + + /* Reconfigure so that the PCI scanner discovers the + device is now multifunction */ + + pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr); + pdev->hdr_type = hdr & 0x7f; + pdev->multifunction = !!(hdr & 0x80); + + break; + } +} + +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, quirk_jmicron_dualfn); + +#endif + #ifdef CONFIG_X86_IO_APIC static void __init quirk_alder_ioapic(struct pci_dev *pdev) { |
