Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg Kroah-Hartman:
 "Here's the large driver core updates for 3.8-rc1.

  The biggest thing here is the various __dev* marking removals.  This
  is going to be a pain for the merge with different subsystem trees, I
  know, but all of the patches included here have been ACKed by their
  various subsystem maintainers, as they wanted them to go through here.

  If this is too much of a pain, I can pull all of them out of this tree
  and just send you one with the other fixes/updates and then, after
  3.8-rc1 is out, do the rest of the removals to ensure we catch them
  all, it's up to you.  The merges should all be trivial, and Stephen
  has been doing them all in linux-next for a few weeks now quite
  easily.

  Other than the __dev* marking removals, there's nothing major here,
  some firmware loading updates and other minor things in the driver
  core.

  All of these have (much to Stephen's annoyance), been in linux-next
  for a while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.

* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
  modpost.c: Stop checking __dev* section mismatches
  init.h: Remove __dev* sections from the kernel
  acpi: remove use of __devinit
  PCI: Remove __dev* markings
  PCI: Always build setup-bus when PCI is enabled
  PCI: Move pci_uevent into pci-driver.c
  PCI: Remove CONFIG_HOTPLUG ifdefs
  unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
  sh/PCI: Remove CONFIG_HOTPLUG ifdefs
  powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
  mips/PCI: Remove CONFIG_HOTPLUG ifdefs
  microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
  dma: remove use of __devinit
  dma: remove use of __devexit_p
  firewire: remove use of __devinitdata
  firewire: remove use of __devinit
  leds: remove use of __devexit
  leds: remove use of __devinit
  leds: remove use of __devexit_p
  mmc: remove use of __devexit
  ...

1 files changed, 66 insertions, 66 deletions

diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 7a451ff..22ad3ee 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -37,7 +37,7 @@
  * key system devices. For devices that need to have mmio decoding always-on,
  * we need to set the dev->mmio_always_on bit.
  */
-static void __devinit quirk_mmio_always_on(struct pci_dev *dev)
+static void quirk_mmio_always_on(struct pci_dev *dev)
 {
 	dev->mmio_always_on = 1;
 }
@@ -48,7 +48,7 @@ DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_ANY_ID, PCI_ANY_ID,
  * Mark this device with a broken_parity_status, to allow
  * PCI scanning code to "skip" this now blacklisted device.
  */
-static void __devinit quirk_mellanox_tavor(struct pci_dev *dev)
+static void quirk_mellanox_tavor(struct pci_dev *dev)
 {
 	dev->broken_parity_status = 1;	/* This device gives false positives */
 }
@@ -83,7 +83,7 @@ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82441,	quirk_p
     This appears to be BIOS not version dependent. So presumably there is a 
     chipset level fix */
     
-static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev)
+static void quirk_isa_dma_hangs(struct pci_dev *dev)
 {
 	if (!isa_dma_bridge_buggy) {
 		isa_dma_bridge_buggy=1;
@@ -106,7 +106,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC,	PCI_DEVICE_ID_NEC_CBUS_3,	quirk_isa_d
  * Intel NM10 "TigerPoint" LPC PM1a_STS.BM_STS must be clear
  * for some HT machines to use C4 w/o hanging.
  */
-static void __devinit quirk_tigerpoint_bm_sts(struct pci_dev *dev)
+static void quirk_tigerpoint_bm_sts(struct pci_dev *dev)
 {
 	u32 pmbase;
 	u16 pm1a;
@@ -125,7 +125,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TGP_LPC, quirk
 /*
  *	Chipsets where PCI->PCI transfers vanish or hang
  */
-static void __devinit quirk_nopcipci(struct pci_dev *dev)
+static void quirk_nopcipci(struct pci_dev *dev)
 {
 	if ((pci_pci_problems & PCIPCI_FAIL)==0) {
 		dev_info(&dev->dev, "Disabling direct PCI/PCI transfers\n");
@@ -135,7 +135,7 @@ static void __devinit quirk_nopcipci(struct pci_dev *dev)
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI,	PCI_DEVICE_ID_SI_5597,		quirk_nopcipci);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI,	PCI_DEVICE_ID_SI_496,		quirk_nopcipci);
 
-static void __devinit quirk_nopciamd(struct pci_dev *dev)
+static void quirk_nopciamd(struct pci_dev *dev)
 {
 	u8 rev;
 	pci_read_config_byte(dev, 0x08, &rev);
@@ -150,7 +150,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD,	PCI_DEVICE_ID_AMD_8151_0,	quirk_nopci
 /*
  *	Triton requires workarounds to be used by the drivers
  */
-static void __devinit quirk_triton(struct pci_dev *dev)
+static void quirk_triton(struct pci_dev *dev)
 {
 	if ((pci_pci_problems&PCIPCI_TRITON)==0) {
 		dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
@@ -229,7 +229,7 @@ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA,	PCI_DEVICE_ID_VIA_8361,		quirk_viala
 /*
  *	VIA Apollo VP3 needs ETBF on BT848/878
  */
-static void __devinit quirk_viaetbf(struct pci_dev *dev)
+static void quirk_viaetbf(struct pci_dev *dev)
 {
 	if ((pci_pci_problems&PCIPCI_VIAETBF)==0) {
 		dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
@@ -238,7 +238,7 @@ static void __devinit quirk_viaetbf(struct pci_dev *dev)
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA,	PCI_DEVICE_ID_VIA_82C597_0,	quirk_viaetbf);
 
-static void __devinit quirk_vsfx(struct pci_dev *dev)
+static void quirk_vsfx(struct pci_dev *dev)
 {
 	if ((pci_pci_problems&PCIPCI_VSFX)==0) {
 		dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
@@ -253,7 +253,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA,	PCI_DEVICE_ID_VIA_82C576,	quirk_vsfx)
  *	workaround applied too
  *	[Info kindly provided by ALi]
  */	
-static void __devinit quirk_alimagik(struct pci_dev *dev)
+static void quirk_alimagik(struct pci_dev *dev)
 {
 	if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) {
 		dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
@@ -267,7 +267,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 	PCI_DEVICE_ID_AL_M1651, 	quirk_alimag
  *	Natoma has some interesting boundary conditions with Zoran stuff
  *	at least
  */
-static void __devinit quirk_natoma(struct pci_dev *dev)
+static void quirk_natoma(struct pci_dev *dev)
 {
 	if ((pci_pci_problems&PCIPCI_NATOMA)==0) {
 		dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n");
@@ -285,7 +285,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 	PCI_DEVICE_ID_INTEL_82443BX_2, 	qu
  *  This chip can cause PCI parity errors if config register 0xA0 is read
  *  while DMAs are occurring.
  */
-static void __devinit quirk_citrine(struct pci_dev *dev)
+static void quirk_citrine(struct pci_dev *dev)
 {
 	dev->cfg_size = 0xA0;
 }
@@ -295,7 +295,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM,	PCI_DEVICE_ID_IBM_CITRINE,	quirk_cit
  *  S3 868 and 968 chips report region size equal to 32M, but they decode 64M.
  *  If it's needed, re-allocate the region.
  */
-static void __devinit quirk_s3_64M(struct pci_dev *dev)
+static void quirk_s3_64M(struct pci_dev *dev)
 {
 	struct resource *r = &dev->resource[0];
 
@@ -313,7 +313,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3,	PCI_DEVICE_ID_S3_968,		quirk_s3_64M);
  * BAR0 should be 8 bytes; instead, it may be set to something like 8k
  * (which conflicts w/ BAR1's memory range).
  */
-static void __devinit quirk_cs5536_vsa(struct pci_dev *dev)
+static void quirk_cs5536_vsa(struct pci_dev *dev)
 {
 	if (pci_resource_len(dev, 0) != 8) {
 		struct resource *res = &dev->resource[0];
@@ -324,7 +324,7 @@ static void __devinit quirk_cs5536_vsa(struct pci_dev *dev)
 }
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa);
 
-static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region,
+static void quirk_io_region(struct pci_dev *dev, unsigned region,
 	unsigned size, int nr, const char *name)
 {
 	region &= ~(size-1);
@@ -352,7 +352,7 @@ static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region,
  *	ATI Northbridge setups MCE the processor if you even
  *	read somewhere between 0x3b0->0x3bb or read 0x3d3
  */
-static void __devinit quirk_ati_exploding_mce(struct pci_dev *dev)
+static void quirk_ati_exploding_mce(struct pci_dev *dev)
 {
 	dev_info(&dev->dev, "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb\n");
 	/* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */
@@ -372,7 +372,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI,	PCI_DEVICE_ID_ATI_RS100,   quirk_ati_
  *	0xE0 (64 bytes of ACPI registers)
  *	0xE2 (32 bytes of SMB registers)
  */
-static void __devinit quirk_ali7101_acpi(struct pci_dev *dev)
+static void quirk_ali7101_acpi(struct pci_dev *dev)
 {
 	u16 region;
 
@@ -440,7 +440,7 @@ static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int
  *	0x90 (16 bytes of SMB registers)
  * and a few strange programmable PIIX4 device resources.
  */
-static void __devinit quirk_piix4_acpi(struct pci_dev *dev)
+static void quirk_piix4_acpi(struct pci_dev *dev)
 {
 	u32 region, res_a;
 
@@ -489,7 +489,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82443MX_3,	qui
  *	0x40 (128 bytes of ACPI, GPIO & TCO registers)
  *	0x58 (64 bytes of GPIO I/O space)
  */
-static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev)
+static void quirk_ich4_lpc_acpi(struct pci_dev *dev)
 {
 	u32 region;
 	u8 enable;
@@ -531,7 +531,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_82801DB_12,
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_82801EB_0,		quirk_ich4_lpc_acpi);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_ESB_1,		quirk_ich4_lpc_acpi);
 
-static void __devinit ich6_lpc_acpi_gpio(struct pci_dev *dev)
+static void ich6_lpc_acpi_gpio(struct pci_dev *dev)
 {
 	u32 region;
 	u8 enable;
@@ -555,7 +555,7 @@ static void __devinit ich6_lpc_acpi_gpio(struct pci_dev *dev)
 	}
 }
 
-static void __devinit ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name, int dynsize)
+static void ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name, int dynsize)
 {
 	u32 val;
 	u32 size, base;
@@ -583,7 +583,7 @@ static void __devinit ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg,
 	dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base+size-1);
 }
 
-static void __devinit quirk_ich6_lpc(struct pci_dev *dev)
+static void quirk_ich6_lpc(struct pci_dev *dev)
 {
 	/* Shared ACPI/GPIO decode with all ICH6+ */
 	ich6_lpc_acpi_gpio(dev);
@@ -595,7 +595,7 @@ static void __devinit quirk_ich6_lpc(struct pci_dev *dev)
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc);
 
-static void __devinit ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name)
+static void ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name)
 {
 	u32 val;
 	u32 mask, base;
@@ -619,7 +619,7 @@ static void __devinit ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg,
 }
 
 /* ICH7-10 has the same common LPC generic IO decode registers */
-static void __devinit quirk_ich7_lpc(struct pci_dev *dev)
+static void quirk_ich7_lpc(struct pci_dev *dev)
 {
 	/* We share the common ACPI/GPIO decode with ICH6 */
 	ich6_lpc_acpi_gpio(dev);
@@ -648,7 +648,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,   PCI_DEVICE_ID_INTEL_ICH10_1, qui
  * VIA ACPI: One IO region pointed to by longword at
  *	0x48 or 0x20 (256 bytes of ACPI registers)
  */
-static void __devinit quirk_vt82c586_acpi(struct pci_dev *dev)
+static void quirk_vt82c586_acpi(struct pci_dev *dev)
 {
 	u32 region;
 
@@ -666,7 +666,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA,	PCI_DEVICE_ID_VIA_82C586_3,	quirk_vt
  *	0x70 (128 bytes of hardware monitoring register)
  *	0x90 (16 bytes of SMB registers)
  */
-static void __devinit quirk_vt82c686_acpi(struct pci_dev *dev)
+static void quirk_vt82c686_acpi(struct pci_dev *dev)
 {
 	u16 hm;
 	u32 smb;
@@ -688,7 +688,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA,	PCI_DEVICE_ID_VIA_82C686_4,	quirk_vt
  *	0x88 (128 bytes of power management registers)
  *	0xd0 (16 bytes of SMB registers)
  */
-static void __devinit quirk_vt8235_acpi(struct pci_dev *dev)
+static void quirk_vt8235_acpi(struct pci_dev *dev)
 {
 	u16 pm, smb;
 
@@ -706,7 +706,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA,	PCI_DEVICE_ID_VIA_8235,	quirk_vt8235
  * TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast back-to-back:
  *	Disable fast back-to-back on the secondary bus segment
  */
-static void __devinit quirk_xio2000a(struct pci_dev *dev)
+static void quirk_xio2000a(struct pci_dev *dev)
 {
 	struct pci_dev *pdev;
 	u16 command;
@@ -780,7 +780,7 @@ DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA,	PCI_DEVICE_ID_VIA_8237,		quirk
  * noapic specified. For the moment we assume it's the erratum. We may be wrong
  * of course. However the advice is demonstrably good even if so..
  */
-static void __devinit quirk_amd_ioapic(struct pci_dev *dev)
+static void quirk_amd_ioapic(struct pci_dev *dev)
 {
 	if (dev->revision >= 0x02) {
 		dev_warn(&dev->dev, "I/O APIC: AMD Erratum #22 may be present. In the event of instability try\n");
@@ -789,7 +789,7 @@ static void __devinit quirk_amd_ioapic(struct pci_dev *dev)
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD,	PCI_DEVICE_ID_AMD_VIPER_7410,	quirk_amd_ioapic);
 
-static void __devinit quirk_ioapic_rmw(struct pci_dev *dev)
+static void quirk_ioapic_rmw(struct pci_dev *dev)
 {
 	if (dev->devfn == 0 && dev->bus->number == 0)
 		sis_apic_bug = 1;
@@ -801,7 +801,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI,	PCI_ANY_ID,			quirk_ioapic_rmw);
  * Some settings of MMRBC can lead to data corruption so block changes.
  * See AMD 8131 HyperTransport PCI-X Tunnel Revision Guide
  */
-static void __devinit quirk_amd_8131_mmrbc(struct pci_dev *dev)
+static void quirk_amd_8131_mmrbc(struct pci_dev *dev)
 {
 	if (dev->subordinate && dev->revision <= 0x12) {
 		dev_info(&dev->dev, "AMD8131 rev %x detected; "
@@ -819,7 +819,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_
  * value of the ACPI SCI interrupt is only done for convenience.
  *	-jgarzik
  */
-static void __devinit quirk_via_acpi(struct pci_dev *d)
+static void quirk_via_acpi(struct pci_dev *d)
 {
 	/*
 	 * VIA ACPI device: SCI IRQ line in PCI config byte 0x42
@@ -926,7 +926,7 @@ DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_vlink);
  * We need to switch it off to be able to recognize the real
  * type of the chip.
  */
-static void __devinit quirk_vt82c598_id(struct pci_dev *dev)
+static void quirk_vt82c598_id(struct pci_dev *dev)
 {
 	pci_write_config_byte(dev, 0xfc, 0);
 	pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device);
@@ -978,7 +978,7 @@ DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD,	PCI_DEVICE_ID_AMD_FE_GATE_700C
  *	assigned to it. We force a larger allocation to ensure that
  *	nothing gets put too close to it.
  */
-static void __devinit quirk_dunord ( struct pci_dev * dev )
+static void quirk_dunord(struct pci_dev *dev)
 {
 	struct resource *r = &dev->resource [1];
 	r->start = 0;
@@ -992,7 +992,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD,	PCI_DEVICE_ID_DUNORD_I3000,	quirk
  * in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80
  * instead of 0x01.
  */
-static void __devinit quirk_transparent_bridge(struct pci_dev *dev)
+static void quirk_transparent_bridge(struct pci_dev *dev)
 {
 	dev->transparent = 1;
 }
@@ -1066,7 +1066,7 @@ DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA
 /*
  *	Serverworks CSB5 IDE does not fully support native mode
  */
-static void __devinit quirk_svwks_csb5ide(struct pci_dev *pdev)
+static void quirk_svwks_csb5ide(struct pci_dev *pdev)
 {
 	u8 prog;
 	pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
@@ -1082,7 +1082,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB
 /*
  *	Intel 82801CAM ICH3-M datasheet says IDE modes must be the same
  */
-static void __devinit quirk_ide_samemode(struct pci_dev *pdev)
+static void quirk_ide_samemode(struct pci_dev *pdev)
 {
 	u8 prog;
 
@@ -1101,7 +1101,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, qui
  * Some ATA devices break if put into D3
  */
 
-static void __devinit quirk_no_ata_d3(struct pci_dev *pdev)
+static void quirk_no_ata_d3(struct pci_dev *pdev)
 {
 	pdev->dev_flags |= PCI_DEV_FLAGS_NO_D3;
 }
@@ -1121,7 +1121,7 @@ DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID,
 /* This was originally an Alpha specific thing, but it really fits here.
  * The i82375 PCI/EISA bridge appears as non-classified. Fix that.
  */
-static void __devinit quirk_eisa_bridge(struct pci_dev *dev)
+static void quirk_eisa_bridge(struct pci_dev *dev)
 {
 	dev->class = PCI_CLASS_BRIDGE_EISA << 8;
 }
@@ -1155,7 +1155,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82375,	quirk_e
  */
 static int asus_hides_smbus;
 
-static void __devinit asus_hides_smbus_hostbridge(struct pci_dev *dev)
+static void asus_hides_smbus_hostbridge(struct pci_dev *dev)
 {
 	if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) {
 		if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB)
@@ -1538,7 +1538,7 @@ DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB3
 #endif
 
 #ifdef CONFIG_X86_IO_APIC
-static void __devinit quirk_alder_ioapic(struct pci_dev *pdev)
+static void quirk_alder_ioapic(struct pci_dev *pdev)
 {
 	int i;
 
@@ -1561,7 +1561,7 @@ static void __devinit quirk_alder_ioapic(struct pci_dev *pdev)
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_EESSC,	quirk_alder_ioapic);
 #endif
 
-static void __devinit quirk_pcie_mch(struct pci_dev *pdev)
+static void quirk_pcie_mch(struct pci_dev *pdev)
 {
 	pci_msi_off(pdev);
 	pdev->no_msi = 1;
@@ -1575,7 +1575,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_E7525_MCH,	quir
  * It's possible for the MSI to get corrupted if shpc and acpi
  * are used together on certain PXH-based systems.
  */
-static void __devinit quirk_pcie_pxh(struct pci_dev *dev)
+static void quirk_pcie_pxh(struct pci_dev *dev)
 {
 	pci_msi_off(dev);
 	dev->no_msi = 1;
@@ -1777,7 +1777,7 @@ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD,   PCI_DEVICE_ID_AMD_8111_SMBUS, 	qui
  * but the PIO transfers won't work if BAR0 falls at the odd 8 bytes.
  * Re-allocate the region if needed...
  */
-static void __devinit quirk_tc86c001_ide(struct pci_dev *dev)
+static void quirk_tc86c001_ide(struct pci_dev *dev)
 {
 	struct resource *r = &dev->resource[0];
 
@@ -1790,7 +1790,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2,
 			 PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE,
 			 quirk_tc86c001_ide);
 
-static void __devinit quirk_netmos(struct pci_dev *dev)
+static void quirk_netmos(struct pci_dev *dev)
 {
 	unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4;
 	unsigned int num_serial = dev->subsystem_device & 0xf;
@@ -1828,7 +1828,7 @@ static void __devinit quirk_netmos(struct pci_dev *dev)
 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID,
 			 PCI_CLASS_COMMUNICATION_SERIAL, 8, quirk_netmos);
 
-static void __devinit quirk_e100_interrupt(struct pci_dev *dev)
+static void quirk_e100_interrupt(struct pci_dev *dev)
 {
 	u16 command, pmcsr;
 	u8 __iomem *csr;
@@ -1901,7 +1901,7 @@ DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
  * The 82575 and 82598 may experience data corruption issues when transitioning
  * out of L0S.  To prevent this we need to disable L0S on the pci-e link
  */
-static void __devinit quirk_disable_aspm_l0s(struct pci_dev *dev)
+static void quirk_disable_aspm_l0s(struct pci_dev *dev)
 {
 	dev_info(&dev->dev, "Disabling L0s\n");
 	pci_disable_link_state(dev, PCIE_LINK_STATE_L0S);
@@ -1921,7 +1921,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s);
 
-static void __devinit fixup_rev1_53c810(struct pci_dev* dev)
+static void fixup_rev1_53c810(struct pci_dev *dev)
 {
 	/* rev 1 ncr53c810 chips don't set the class at all which means
 	 * they don't get their resources remapped. Fix that here.
@@ -1935,7 +1935,7 @@ static void __devinit fixup_rev1_53c810(struct pci_dev* dev)
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
 
 /* Enable 1k I/O space granularity on the Intel P64H2 */
-static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
+static void quirk_p64h2_1k_io(struct pci_dev *dev)
 {
 	u16 en1k;
 
@@ -1968,7 +1968,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA,  PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA,  PCI_DEVICE_ID_NVIDIA_CK804_PCIE,
 			quirk_nvidia_ck804_pcie_aer_ext_cap);
 
-static void __devinit quirk_via_cx700_pci_parking_caching(struct pci_dev *dev)
+static void quirk_via_cx700_pci_parking_caching(struct pci_dev *dev)
 {
 	/*
 	 * Disable PCI Bus Parking and PCI Master read caching on CX700
@@ -2031,7 +2031,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_c
  * We believe that it is legal to read beyond the end tag and
  * therefore the solution is to limit the read/write length.
  */
-static void __devinit quirk_brcm_570x_limit_vpd(struct pci_dev *dev)
+static void quirk_brcm_570x_limit_vpd(struct pci_dev *dev)
 {
 	/*
 	 * Only disable the VPD capability for 5706, 5706S, 5708,
@@ -2091,7 +2091,7 @@ DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_BROADCOM,
  * the DRBs - this is where we expose device 6.
  * http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm
  */
-static void __devinit quirk_unhide_mch_dev6(struct pci_dev *dev)
+static void quirk_unhide_mch_dev6(struct pci_dev *dev)
 {
 	u8 reg;
 
@@ -2115,7 +2115,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB,
  * supports link speed auto negotiation, but falsely sets
  * the link speed to 5GT/s.
  */
-static void __devinit quirk_tile_plx_gen1(struct pci_dev *dev)
+static void quirk_tile_plx_gen1(struct pci_dev *dev)
 {
 	if (tile_plx_gen1) {
 		pci_write_config_dword(dev, 0x98, 0x1);
@@ -2132,7 +2132,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8624, quirk_tile_plx_gen1);
  * aware of it.  Instead of setting the flag on all busses in the
  * machine, simply disable MSI globally.
  */
-static void __devinit quirk_disable_all_msi(struct pci_dev *dev)
+static void quirk_disable_all_msi(struct pci_dev *dev)
 {
 	pci_no_msi();
 	dev_warn(&dev->dev, "MSI quirk detected; MSI disabled\n");
@@ -2146,7 +2146,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disab
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8380_0, quirk_disable_all_msi);
 
 /* Disable MSI on chipsets that are known to not support it */
-static void __devinit quirk_disable_msi(struct pci_dev *dev)
+static void quirk_disable_msi(struct pci_dev *dev)
 {
 	if (dev->subordinate) {
 		dev_warn(&dev->dev, "MSI quirk detected; "
@@ -2164,7 +2164,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x5a3f, quirk_disable_msi);
  * we use the possible vendor/device IDs of the host bridge for the
  * declared quirk, and search for the APC bridge by slot number.
  */
-static void __devinit quirk_amd_780_apc_msi(struct pci_dev *host_bridge)
+static void quirk_amd_780_apc_msi(struct pci_dev *host_bridge)
 {
 	struct pci_dev *apc_bridge;
 
@@ -2272,7 +2272,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE,
  * for the MCP55 NIC. It is not yet determined whether the msi problem
  * also affects other devices. As for now, turn off msi for this device.
  */
-static void __devinit nvenet_msi_disable(struct pci_dev *dev)
+static void nvenet_msi_disable(struct pci_dev *dev)
 {
 	const char *board_name = dmi_get_system_info(DMI_BOARD_NAME);
 
@@ -2298,7 +2298,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
  * we have it set correctly.
  * Note this is an undocumented register.
  */
-static void __devinit nvbridge_check_legacy_irq_routing(struct pci_dev *dev)
+static void nvbridge_check_legacy_irq_routing(struct pci_dev *dev)
 {
 	u32 cfg;
 
@@ -2534,11 +2534,11 @@ DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_q
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
 
-static void __devinit quirk_msi_intx_disable_bug(struct pci_dev *dev)
+static void quirk_msi_intx_disable_bug(struct pci_dev *dev)
 {
 	dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG;
 }
-static void __devinit quirk_msi_intx_disable_ati_bug(struct pci_dev *dev)
+static void quirk_msi_intx_disable_ati_bug(struct pci_dev *dev)
 {
 	struct pci_dev *p;
 
@@ -2612,7 +2612,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1083,
  * kernel fails to allocate resources when hotplug device is 
  * inserted and PCI bus is rescanned.
  */
-static void __devinit quirk_hotplug_bridge(struct pci_dev *dev)
+static void quirk_hotplug_bridge(struct pci_dev *dev)
 {
 	dev->is_hotplug_bridge = 1;
 }
@@ -2752,7 +2752,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors);
 #endif
 
-static void __devinit fixup_ti816x_class(struct pci_dev* dev)
+static void fixup_ti816x_class(struct pci_dev *dev)
 {
 	/* TI 816x devices do not have class code set when in PCIe boot mode */
 	dev_info(&dev->dev, "Setting PCI class for 816x PCIe device\n");
@@ -2764,7 +2764,7 @@ DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_TI, 0xb800,
 /* Some PCIe devices do not work reliably with the claimed maximum
  * payload size supported.
  */
-static void __devinit fixup_mpss_256(struct pci_dev *dev)
+static void fixup_mpss_256(struct pci_dev *dev)
 {
 	dev->pcie_mpss = 1; /* 256 bytes */
 }
@@ -2782,7 +2782,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE,
  * coalescing must be disabled.  Unfortunately, it cannot be re-enabled because
  * it is possible to hotplug a device with MPS of 256B.
  */
-static void __devinit quirk_intel_mc_errata(struct pci_dev *dev)
+static void quirk_intel_mc_errata(struct pci_dev *dev)
 {
 	int err;
 	u16 rcc;
@@ -2888,7 +2888,7 @@ static void fixup_debug_report(struct pci_dev *dev, ktime_t calltime,
  * This resolves crashes often seen on monitor unplug.
  */
 #define I915_DEIER_REG 0x4400c
-static void __devinit disable_igfx_irq(struct pci_dev *dev)
+static void disable_igfx_irq(struct pci_dev *dev)
 {
 	void __iomem *regs = pci_iomap(dev, 0, 0);
 	if (regs == NULL) {
@@ -2914,7 +2914,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x010a, disable_igfx_irq);
  * PCI_COMMAND_INTX_DISABLE works though they actually do not properly
  * support this feature.
  */
-static void __devinit quirk_broken_intx_masking(struct pci_dev *dev)
+static void quirk_broken_intx_masking(struct pci_dev *dev)
 {
 	dev->broken_intx_masking = 1;
 }