iwlwifi: move some configuration parameters into DVM

There are a number of parameters that aren't really hardware
specific but rather define how the DVM firmware is used.
Move these into the DVM configuration.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

1 files changed, 1 insertions, 42 deletions

diff --git a/drivers/net/wireless/iwlwifi/iwl-config.h b/drivers/net/wireless/iwlwifi/iwl-config.h
index c3c9268..a193832 100644
--- a/drivers/net/wireless/iwlwifi/iwl-config.h
+++ b/drivers/net/wireless/iwlwifi/iwl-config.h
@@ -136,17 +136,9 @@ enum iwl_led_mode {
  * @led_compensation: compensate on the led on/off time per HW according
  *	to the deviation to achieve the desired led frequency.
  *	The detail algorithm is described in iwl-led.c
- * @chain_noise_num_beacons: number of beacons used to compute chain noise
- * @adv_thermal_throttle: support advance thermal throttle
- * @support_ct_kill_exit: support ct kill exit condition
- * @plcp_delta_threshold: plcp error rate threshold used to trigger
- *	radio tuning when there is a high receiving plcp error rate
- * @chain_noise_scale: default chain noise scale used for gain computation
  * @wd_timeout: TX queues watchdog timeout
  * @max_event_log_size: size of event log buffer size for ucode event logging
  * @shadow_reg_enable: HW shadow register support
- * @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up
- * @no_idle_support: do not support idle mode
  */
 struct iwl_base_params {
 	int eeprom_size;
@@ -157,31 +149,9 @@ struct iwl_base_params {
 	const u16 max_ll_items;
 	const bool shadow_ram_support;
 	u16 led_compensation;
-	bool adv_thermal_throttle;
-	bool support_ct_kill_exit;
-	u8 plcp_delta_threshold;
-	s32 chain_noise_scale;
 	unsigned int wd_timeout;
 	u32 max_event_log_size;
 	const bool shadow_reg_enable;
-	const bool hd_v2;
-	const bool no_idle_support;
-};
-
-/*
- * @advanced_bt_coexist: support advanced bt coexist
- * @bt_init_traffic_load: specify initial bt traffic load
- * @bt_prio_boost: default bt priority boost value
- * @agg_time_limit: maximum number of uSec in aggregation
- * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode
- */
-struct iwl_bt_params {
-	bool advanced_bt_coexist;
-	u8 bt_init_traffic_load;
-	u32 bt_prio_boost;
-	u16 agg_time_limit;
-	bool bt_sco_disable;
-	bool bt_session_2;
 };
 
 /*
@@ -231,16 +201,10 @@ struct iwl_eeprom_params {
  * @nvm_calib_ver: NVM calibration version
  * @lib: pointer to the lib ops
  * @base_params: pointer to basic parameters
- * @ht_params: point to ht patameters
- * @bt_params: pointer to bt parameters
- * @need_temp_offset_calib: need to perform temperature offset calibration
- * @no_xtal_calib: some devices do not need crystal calibration data,
- *	don't send it to those
+ * @ht_params: point to ht parameters
  * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off)
- * @adv_pm: advance power management
  * @rx_with_siso_diversity: 1x1 device with rx antenna diversity
  * @internal_wimax_coex: internal wifi/wimax combo device
- * @temp_offset_v2: support v2 of temperature offset calibration
  *
  * We enable the driver to be backward compatible wrt. hardware features.
  * API differences in uCode shouldn't be handled here but through TLVs
@@ -264,15 +228,10 @@ struct iwl_cfg {
 	const struct iwl_base_params *base_params;
 	/* params likely to change within a device family */
 	const struct iwl_ht_params *ht_params;
-	const struct iwl_bt_params *bt_params;
 	const struct iwl_eeprom_params *eeprom_params;
-	const bool need_temp_offset_calib; /* if used set to true */
-	const bool no_xtal_calib;
 	enum iwl_led_mode led_mode;
-	const bool adv_pm;
 	const bool rx_with_siso_diversity;
 	const bool internal_wimax_coex;
-	const bool temp_offset_v2;
 };
 
 /*