brcmfmac: add out of band interrupt support

Some sdio host controllers do not support real in band interrupt.
Software polling mode as a replacement is not fast enough for
high throughput and new features. Also some in band interrupts
do not support host wake up on embedded platform even when they
are real physical interrupts. Therefore out of band (oob)
interrupt mechanism is implemented for these scenarios.

To provide oob irq number and flags used for irq registration in
brcmfmac, a platform device contains irq resource must be
registered in board specific code.

Here is an example of platform device structure:
struct resource brcmf_sdio_res[] = {
	{
		.start	= GPIO_BRCMF_SDIO_OOB_NUM,
		.end	= GPIO_BRCMF_SDIO_OOB_NUM,
		.flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
	}
};
struct platform_device brcmf_sdio_device = {
	.name		= "brcmf_sdio_pd",
	.id		= -1,
	.num_resources	= ARRAY_SIZE(brcmf_sdio_res),
	.resource	= brcmf_sdio_res,
};

Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 17 insertions, 5 deletions

diff --git a/drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h b/drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h
index 0281d20..7010eaf 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h
+++ b/drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h
@@ -43,6 +43,13 @@
 /* as of sdiod rev 0, supports 3 functions */
 #define SBSDIO_NUM_FUNCTION		3
 
+/* function 0 vendor specific CCCR registers */
+#define SDIO_CCCR_BRCM_SEPINT		0xf2
+
+#define  SDIO_SEPINT_MASK		0x01
+#define  SDIO_SEPINT_OE			0x02
+#define  SDIO_SEPINT_ACT_HI		0x04
+
 /* function 1 miscellaneous registers */
 
 /* sprom command and status */
@@ -144,13 +151,18 @@ struct brcmf_sdio_dev {
 	wait_queue_head_t request_buffer_wait;
 	struct device *dev;
 	struct brcmf_bus *bus_if;
+#ifdef CONFIG_BRCMFMAC_SDIO_OOB
+	unsigned int irq;		/* oob interrupt number */
+	unsigned long irq_flags;	/* board specific oob flags */
+	bool irq_en;			/* irq enable flags */
+	spinlock_t irq_en_lock;
+	bool irq_wake;			/* irq wake enable flags */
+#endif		/* CONFIG_BRCMFMAC_SDIO_OOB */
 };
 
-/* Register/deregister device interrupt handler. */
-extern int
-brcmf_sdcard_intr_reg(struct brcmf_sdio_dev *sdiodev);
-
-extern int brcmf_sdcard_intr_dereg(struct brcmf_sdio_dev *sdiodev);
+/* Register/deregister interrupt handler. */
+extern int brcmf_sdio_intr_register(struct brcmf_sdio_dev *sdiodev);
+extern int brcmf_sdio_intr_unregister(struct brcmf_sdio_dev *sdiodev);
 
 /* Access SDIO address space (e.g. CCCR) using CMD52 (single-byte interface).
  *   fn:   function number