Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
  mac80211: fix reorder buffer release
  iwmc3200wifi: Enable wimax core through module parameter
  iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
  iwmc3200wifi: Coex table command does not expect a response
  iwmc3200wifi: Update wiwi priority table
  iwlwifi: driver version track kernel version
  iwlwifi: indicate uCode type when fail dump error/event log
  iwl3945: remove duplicated event logging code
  b43: fix two warnings
  ipw2100: fix rebooting hang with driver loaded
  cfg80211: indent regulatory messages with spaces
  iwmc3200wifi: fix NULL pointer dereference in pmkid update
  mac80211: Fix TX status reporting for injected data frames
  ath9k: enable 2GHz band only if the device supports it
  airo: Fix integer overflow warning
  rt2x00: Fix padding bug on L2PAD devices.
  WE: Fix set events not propagated
  b43legacy: avoid PPC fault during resume
  b43: avoid PPC fault during resume
  tcp: fix a timewait refcnt race
  ...

Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
	kernel/sysctl_check.c
	net/ipv4/sysctl_net_ipv4.c
	net/ipv6/addrconf.c
	net/sctp/sysctl.c

1 files changed, 11 insertions, 22 deletions

diff --git a/drivers/net/wireless/ath/ath5k/reset.c b/drivers/net/wireless/ath/ath5k/reset.c
index 34e13c7..62954fc 100644
--- a/drivers/net/wireless/ath/ath5k/reset.c
+++ b/drivers/net/wireless/ath/ath5k/reset.c
@@ -25,6 +25,8 @@
   Reset functions and helpers
 \*****************************/
 
+#include <asm/unaligned.h>
+
 #include <linux/pci.h> 		/* To determine if a card is pci-e */
 #include <linux/log2.h>
 #include "ath5k.h"
@@ -870,6 +872,7 @@ static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah,
 int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
 	struct ieee80211_channel *channel, bool change_channel)
 {
+	struct ath_common *common = ath5k_hw_common(ah);
 	u32 s_seq[10], s_ant, s_led[3], staid1_flags, tsf_up, tsf_lo;
 	u32 phy_tst1;
 	u8 mode, freq, ee_mode, ant[2];
@@ -1171,10 +1174,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
 	ath5k_hw_reg_write(ah, s_led[2], AR5K_GPIODO);
 
 	/* Restore sta_id flags and preserve our mac address*/
-	ath5k_hw_reg_write(ah, AR5K_LOW_ID(ah->ah_sta_id),
-						AR5K_STA_ID0);
-	ath5k_hw_reg_write(ah, staid1_flags | AR5K_HIGH_ID(ah->ah_sta_id),
-						AR5K_STA_ID1);
+	ath5k_hw_reg_write(ah,
+			   get_unaligned_le32(common->macaddr),
+			   AR5K_STA_ID0);
+	ath5k_hw_reg_write(ah,
+			   staid1_flags | get_unaligned_le16(common->macaddr + 4),
+			   AR5K_STA_ID1);
 
 
 	/*
@@ -1182,8 +1187,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
 	 */
 
 	/* Restore bssid and bssid mask */
-	/* XXX: add ah->aid once mac80211 gives this to us */
-	ath5k_hw_set_associd(ah, ah->ah_bssid, 0);
+	ath5k_hw_set_associd(ah);
 
 	/* Set PCU config */
 	ath5k_hw_set_opmode(ah);
@@ -1289,7 +1293,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
 	 * out and/or noise floor calibration might timeout.
 	 */
 	AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
-				AR5K_PHY_AGCCTL_CAL);
+				AR5K_PHY_AGCCTL_CAL | AR5K_PHY_AGCCTL_NF);
 
 	/* At the same time start I/Q calibration for QAM constellation
 	 * -no need for CCK- */
@@ -1310,21 +1314,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
 			channel->center_freq);
 	}
 
-	/*
-	 * If we run NF calibration before AGC, it always times out.
-	 * Binary HAL starts NF and AGC calibration at the same time
-	 * and only waits for AGC to finish. Also if AGC or NF cal.
-	 * times out, reset doesn't fail on binary HAL. I believe
-	 * that's wrong because since rx path is routed to a detector,
-	 * if cal. doesn't finish we won't have RX. Sam's HAL for AR5210/5211
-	 * enables noise floor calibration after offset calibration and if noise
-	 * floor calibration fails, reset fails. I believe that's
-	 * a better approach, we just need to find a polling interval
-	 * that suits best, even if reset continues we need to make
-	 * sure that rx path is ready.
-	 */
-	ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
-
 	/* Restore antenna mode */
 	ath5k_hw_set_antenna_mode(ah, ah->ah_ant_mode);