Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

11 files changed, 68 insertions, 62 deletions

diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index d863075..905e214 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -258,7 +258,8 @@ static int e1000_set_settings(struct net_device *netdev,
 	 * When SoL/IDER sessions are active, autoneg/speed/duplex
 	 * cannot be changed
 	 */
-	if (hw->phy.ops.check_reset_block(hw)) {
+	if (hw->phy.ops.check_reset_block &&
+	    hw->phy.ops.check_reset_block(hw)) {
 		e_err("Cannot change link characteristics when SoL/IDER is active.\n");
 		return -EINVAL;
 	}
@@ -1615,7 +1616,8 @@ static int e1000_loopback_test(struct e1000_adapter *adapter, u64 *data)
 	 * PHY loopback cannot be performed if SoL/IDER
 	 * sessions are active
 	 */
-	if (hw->phy.ops.check_reset_block(hw)) {
+	if (hw->phy.ops.check_reset_block &&
+	    hw->phy.ops.check_reset_block(hw)) {
 		e_err("Cannot do PHY loopback test when SoL/IDER is active.\n");
 		*data = 0;
 		goto out;
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 026e8b3..a134399 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -709,7 +709,7 @@ s32 e1000e_setup_link_generic(struct e1000_hw *hw)
 	 * In the case of the phy reset being blocked, we already have a link.
 	 * We do not need to set it up again.
 	 */
-	if (hw->phy.ops.check_reset_block(hw))
+	if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw))
 		return 0;
 
 	/*
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index a4b0435..31d37a2 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -6237,7 +6237,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 		adapter->hw.phy.ms_type = e1000_ms_hw_default;
 	}
 
-	if (hw->phy.ops.check_reset_block(hw))
+	if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw))
 		e_info("PHY reset is blocked due to SOL/IDER session.\n");
 
 	/* Set initial default active device features */
@@ -6404,7 +6404,7 @@ err_register:
 	if (!(adapter->flags & FLAG_HAS_AMT))
 		e1000e_release_hw_control(adapter);
 err_eeprom:
-	if (!hw->phy.ops.check_reset_block(hw))
+	if (hw->phy.ops.check_reset_block && !hw->phy.ops.check_reset_block(hw))
 		e1000_phy_hw_reset(&adapter->hw);
 err_hw_init:
 	kfree(adapter->tx_ring);
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 0334d01..b860d4f 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -2155,9 +2155,11 @@ s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
 	s32 ret_val;
 	u32 ctrl;
 
-	ret_val = phy->ops.check_reset_block(hw);
-	if (ret_val)
-		return 0;
+	if (phy->ops.check_reset_block) {
+		ret_val = phy->ops.check_reset_block(hw);
+		if (ret_val)
+			return 0;
+	}
 
 	ret_val = phy->ops.acquire(hw);
 	if (ret_val)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index bf20457..17ad6a3 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -1390,6 +1390,8 @@ static void ixgbe_process_skb_fields(struct ixgbe_ring *rx_ring,
 				     union ixgbe_adv_rx_desc *rx_desc,
 				     struct sk_buff *skb)
 {
+	struct net_device *dev = rx_ring->netdev;
+
 	ixgbe_update_rsc_stats(rx_ring, skb);
 
 	ixgbe_rx_hash(rx_ring, rx_desc, skb);
@@ -1401,14 +1403,15 @@ static void ixgbe_process_skb_fields(struct ixgbe_ring *rx_ring,
 		ixgbe_ptp_rx_hwtstamp(rx_ring->q_vector, skb);
 #endif
 
-	if (ixgbe_test_staterr(rx_desc, IXGBE_RXD_STAT_VP)) {
+	if ((dev->features & NETIF_F_HW_VLAN_RX) &&
+	    ixgbe_test_staterr(rx_desc, IXGBE_RXD_STAT_VP)) {
 		u16 vid = le16_to_cpu(rx_desc->wb.upper.vlan);
 		__vlan_hwaccel_put_tag(skb, vid);
 	}
 
 	skb_record_rx_queue(skb, rx_ring->queue_index);
 
-	skb->protocol = eth_type_trans(skb, rx_ring->netdev);
+	skb->protocol = eth_type_trans(skb, dev);
 }
 
 static void ixgbe_rx_skb(struct ixgbe_q_vector *q_vector,
@@ -3607,10 +3610,6 @@ static void ixgbe_configure_dcb(struct ixgbe_adapter *adapter)
 	if (hw->mac.type == ixgbe_mac_82598EB)
 		netif_set_gso_max_size(adapter->netdev, 32768);
 
-
-	/* Enable VLAN tag insert/strip */
-	adapter->netdev->features |= NETIF_F_HW_VLAN_RX;
-
 	hw->mac.ops.set_vfta(&adapter->hw, 0, 0, true);
 
 #ifdef IXGBE_FCOE
@@ -6701,11 +6700,6 @@ static netdev_features_t ixgbe_fix_features(struct net_device *netdev,
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 
-#ifdef CONFIG_DCB
-	if (adapter->flags & IXGBE_FLAG_DCB_ENABLED)
-		features &= ~NETIF_F_HW_VLAN_RX;
-#endif
-
 	/* return error if RXHASH is being enabled when RSS is not supported */
 	if (!(adapter->flags & IXGBE_FLAG_RSS_ENABLED))
 		features &= ~NETIF_F_RXHASH;
@@ -6718,7 +6712,6 @@ static netdev_features_t ixgbe_fix_features(struct net_device *netdev,
 	if (!(adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE))
 		features &= ~NETIF_F_LRO;
 
-
 	return features;
 }
 
@@ -6766,6 +6759,11 @@ static int ixgbe_set_features(struct net_device *netdev,
 		need_reset = true;
 	}
 
+	if (features & NETIF_F_HW_VLAN_RX)
+		ixgbe_vlan_strip_enable(adapter);
+	else
+		ixgbe_vlan_strip_disable(adapter);
+
 	if (changed & NETIF_F_RXALL)
 		need_reset = true;
 
diff --git a/drivers/net/ethernet/marvell/mv643xx_eth.c b/drivers/net/ethernet/marvell/mv643xx_eth.c
index ec85bf1..770ee55 100644
--- a/drivers/net/ethernet/marvell/mv643xx_eth.c
+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
@@ -436,7 +436,9 @@ struct mv643xx_eth_private {
 	/*
 	 * Hardware-specific parameters.
 	 */
+#if defined(CONFIG_HAVE_CLK)
 	struct clk *clk;
+#endif
 	unsigned int t_clk;
 };
 
@@ -2895,17 +2897,17 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
 	mp->dev = dev;
 
 	/*
-	 * Get the clk rate, if there is one, otherwise use the default.
+	 * Start with a default rate, and if there is a clock, allow
+	 * it to override the default.
 	 */
+	mp->t_clk = 133000000;
+#if defined(CONFIG_HAVE_CLK)
 	mp->clk = clk_get(&pdev->dev, (pdev->id ? "1" : "0"));
 	if (!IS_ERR(mp->clk)) {
 		clk_prepare_enable(mp->clk);
 		mp->t_clk = clk_get_rate(mp->clk);
-	} else {
-		mp->t_clk = 133000000;
-		printk(KERN_WARNING "Unable to get clock");
 	}
-
+#endif
 	set_params(mp, pd);
 	netif_set_real_num_tx_queues(dev, mp->txq_count);
 	netif_set_real_num_rx_queues(dev, mp->rxq_count);
@@ -2995,10 +2997,13 @@ static int mv643xx_eth_remove(struct platform_device *pdev)
 		phy_detach(mp->phy);
 	cancel_work_sync(&mp->tx_timeout_task);
 
+#if defined(CONFIG_HAVE_CLK)
 	if (!IS_ERR(mp->clk)) {
 		clk_disable_unprepare(mp->clk);
 		clk_put(mp->clk);
 	}
+#endif
+
 	free_netdev(mp->dev);
 
 	platform_set_drvdata(pdev, NULL);
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 0364283..0076f77 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -13,9 +13,8 @@ config STMMAC_ETH
 if STMMAC_ETH
 
 config STMMAC_PLATFORM
-	tristate "STMMAC platform bus support"
+	bool "STMMAC Platform bus support"
 	depends on STMMAC_ETH
-	default y
 	---help---
 	  This selects the platform specific bus support for
 	  the stmmac device driver. This is the driver used
@@ -26,7 +25,7 @@ config STMMAC_PLATFORM
 	  If unsure, say N.
 
 config STMMAC_PCI
-	tristate "STMMAC support on PCI bus (EXPERIMENTAL)"
+	bool "STMMAC PCI bus support (EXPERIMENTAL)"
 	depends on STMMAC_ETH && PCI && EXPERIMENTAL
 	---help---
 	  This is to select the Synopsys DWMAC available on PCI devices,
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 6b5d060..6d07ba2 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -95,7 +95,8 @@ extern int stmmac_mdio_register(struct net_device *ndev);
 extern void stmmac_set_ethtool_ops(struct net_device *netdev);
 extern const struct stmmac_desc_ops enh_desc_ops;
 extern const struct stmmac_desc_ops ndesc_ops;
-
+extern struct pci_driver stmmac_pci_driver;
+extern struct platform_driver stmmac_pltfr_driver;
 int stmmac_freeze(struct net_device *ndev);
 int stmmac_restore(struct net_device *ndev);
 int stmmac_resume(struct net_device *ndev);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 0caae72..8899e10 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -42,6 +42,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/slab.h>
 #include <linux/prefetch.h>
+#include <linux/pci.h>
 #ifdef CONFIG_STMMAC_DEBUG_FS
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
@@ -833,8 +834,9 @@ static u32 stmmac_get_synopsys_id(struct stmmac_priv *priv)
 
 /**
  * stmmac_selec_desc_mode
- * @dev : device pointer
- * Description: select the Enhanced/Alternate or Normal descriptors */
+ * @priv : private structure
+ * Description: select the Enhanced/Alternate or Normal descriptors
+ */
 static void stmmac_selec_desc_mode(struct stmmac_priv *priv)
 {
 	if (priv->plat->enh_desc) {
@@ -1860,6 +1862,8 @@ static int stmmac_hw_init(struct stmmac_priv *priv)
 /**
  * stmmac_dvr_probe
  * @device: device pointer
+ * @plat_dat: platform data pointer
+ * @addr: iobase memory address
  * Description: this is the main probe function used to
  * call the alloc_etherdev, allocate the priv structure.
  */
@@ -2089,6 +2093,30 @@ int stmmac_restore(struct net_device *ndev)
 }
 #endif /* CONFIG_PM */
 
+static int __init stmmac_init(void)
+{
+	int err = 0;
+
+	err = platform_driver_register(&stmmac_pltfr_driver);
+
+	if (!err) {
+		err = pci_register_driver(&stmmac_pci_driver);
+		if (err)
+			platform_driver_unregister(&stmmac_pltfr_driver);
+	}
+
+	return err;
+}
+
+static void __exit stmmac_exit(void)
+{
+	pci_unregister_driver(&stmmac_pci_driver);
+	platform_driver_unregister(&stmmac_pltfr_driver);
+}
+
+module_init(stmmac_init);
+module_exit(stmmac_exit);
+
 #ifndef MODULE
 static int __init stmmac_cmdline_opt(char *str)
 {
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
index 58fab53..cf826e6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
@@ -179,7 +179,7 @@ static DEFINE_PCI_DEVICE_TABLE(stmmac_id_table) = {
 
 MODULE_DEVICE_TABLE(pci, stmmac_id_table);
 
-static struct pci_driver stmmac_driver = {
+struct pci_driver stmmac_pci_driver = {
 	.name = STMMAC_RESOURCE_NAME,
 	.id_table = stmmac_id_table,
 	.probe = stmmac_pci_probe,
@@ -190,33 +190,6 @@ static struct pci_driver stmmac_driver = {
 #endif
 };
 
-/**
- * stmmac_init_module - Entry point for the driver
- * Description: This function is the entry point for the driver.
- */
-static int __init stmmac_init_module(void)
-{
-	int ret;
-
-	ret = pci_register_driver(&stmmac_driver);
-	if (ret < 0)
-		pr_err("%s: ERROR: driver registration failed\n", __func__);
-
-	return ret;
-}
-
-/**
- * stmmac_cleanup_module - Cleanup routine for the driver
- * Description: This function is the cleanup routine for the driver.
- */
-static void __exit stmmac_cleanup_module(void)
-{
-	pci_unregister_driver(&stmmac_driver);
-}
-
-module_init(stmmac_init_module);
-module_exit(stmmac_cleanup_module);
-
 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet PCI driver");
 MODULE_AUTHOR("Rayagond Kokatanur <rayagond.kokatanur@vayavyalabs.com>");
 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index df4774d..20eb502 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -255,7 +255,7 @@ static const struct of_device_id stmmac_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, stmmac_dt_ids);
 
-static struct platform_driver stmmac_driver = {
+struct platform_driver stmmac_pltfr_driver = {
 	.probe = stmmac_pltfr_probe,
 	.remove = stmmac_pltfr_remove,
 	.driver = {
@@ -266,8 +266,6 @@ static struct platform_driver stmmac_driver = {
 		   },
 };
 
-module_platform_driver(stmmac_driver);
-
 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet PLATFORM driver");
 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
 MODULE_LICENSE("GPL");