dgrs: remove from build, config, and maintainer list

Stop building and configuring driver for Digi RightSwitch, which was
never actually sold to anyone, and remove it from MAINTAINERS.

In response to an investigation into the firmware of the "Digi Rightswitch"
driver, Andres Salomon discovered:
>
> Dear Andres:
>
> After further research, we found that this product was killed in place
> and never reached the market.  We would like to request that this not be
> included.

Since the product never reached market, clearly nobody is using this orphaned
driver.

Signed-off-by: Nathanael Nerode <neroden@gcc.gnu.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 0 insertions, 473 deletions

diff --git a/drivers/net/dgrs_i82596.h b/drivers/net/dgrs_i82596.h
deleted file mode 100644
index ac9217a..0000000
--- a/drivers/net/dgrs_i82596.h
+++ /dev/null
@@ -1,473 +0,0 @@
-/*
- *	i82596 ethernet controller bits and structures (little endian)
- *
- *	$Id: i82596.h,v 1.8 1996/09/03 11:19:03 rick Exp $
- */
-
-/************************************************************************/
-/*									*/
-/*	PORT commands (p. 4-20).  The least significant nibble is one	*/
-/*	of these commands, the rest of the command is a memory address	*/
-/*	aligned on a 16 byte boundary.  Note that port commands must	*/
-/*	be written to the PORT address and the PORT address+2 with two	*/
-/*	halfword writes.  Write the LSH first to PORT, then the MSH to	*/
-/*	PORT+2.  Blame Intel.						*/
-/*									*/
-/************************************************************************/
-#define	I596_PORT_RESET		0x0	/* Reset. Wait 5 SysClks & 10 TxClks */
-#define	I596_PORT_SELFTEST	0x1	/* Do a selftest */
-#define	I596_PORT_SCP_ADDR	0x2	/* Set new SCP address */
-#define	I596_PORT_DUMP		0x3	/* Dump internal data structures */
-
-/*
- *	I596_ST:	Selftest results (p. 4-21)
- */
-typedef volatile struct
-{
-	ulong	signature;	/* ROM checksum */
-	ulong	result;		/* Selftest results: non-zero is a failure */
-} I596_ST;
-
-#define	I596_ST_SELFTEST_FAIL	0x1000	/* Selftest Failed */
-#define	I596_ST_DIAGNOSE_FAIL	0x0020	/* Diagnose Failed */
-#define	I596_ST_BUSTIMER_FAIL	0x0010	/* Bus Timer Failed */
-#define	I596_ST_REGISTER_FAIL	0x0008	/* Register Failed */
-#define	I596_ST_ROM_FAIL	0x0004	/* ROM Failed */
-
-/*
- *	I596_DUMP:	Dump results
- */
-typedef volatile struct
-{
-	ulong	dump[77];
-} I596_DUMP;
-
-/************************************************************************/
-/*									*/
-/*	I596_TBD:	Transmit Buffer Descriptor (p. 4-59)		*/
-/*									*/
-/************************************************************************/
-typedef volatile struct _I596_TBD
-{
-	ulong			count;
-	vol struct _I596_TBD	*next;
-	uchar			*buf;
-	ushort			unused1;
-	ushort			unused2;
-} I596_TBD;
-
-#define	I596_TBD_NOLINK		((I596_TBD *) 0xffffffff)
-#define	I596_TBD_EOF		0x8000
-#define I596_TBD_COUNT_MASK	0x3fff
-
-/************************************************************************/
-/*									*/
-/*	I596_TFD:	Transmit Frame Descriptor (p. 4-56)		*/
-/*			a.k.a. I596_CB_XMIT				*/
-/*									*/
-/************************************************************************/
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-	I596_TBD		*tbdp;
-	ulong			count;	/* for speed */
-
-	/* Application defined data follows structure... */
-
-#if 0	/* We don't use these intel defined ones */
-		uchar			addr[6];
-		ushort			len;
-		uchar			data[1];
-#else
-		ulong		dstchan;/* Used by multi-NIC mode */
-#endif
-} I596_TFD;
-
-#define	I596_TFD_NOCRC	0x0010	/* cmd: No CRC insertion */
-#define	I596_TFD_FLEX	0x0008	/* cmd: Flexible mode */
-
-/************************************************************************/
-/*									*/
-/*	I596_RBD:	Receive Buffer Descriptor (p. 4-84)		*/
-/*									*/
-/************************************************************************/
-typedef volatile struct _I596_RBD
-{
-#ifdef INTEL_RETENTIVE
-	ushort			count;	/* Length of data in buf */
-	ushort			offset;
-#else
-	ulong			count;	/* Length of data in buf */
-#endif
-	vol struct _I596_RBD	*next;	/* Next buffer descriptor in list */
-	uchar			*buf;	/* Data buffer */
-#ifdef INTEL_RETENTIVE
-	ushort			size;	/* Size of buf (constant) */
-	ushort			zero;
-#else
-	ulong			size;	/* Size of buf (constant) */
-#endif
-
-	/* Application defined data follows structure... */
-
-	uchar			chan;
-	uchar			refcnt;
-	ushort			len;
-} I596_RBD;
-
-#define	I596_RBD_NOLINK		((I596_RBD *) 0xffffffff)
-#define	I596_RBD_EOF		0x8000	/* This is last buffer in a frame */
-#define	I596_RBD_F		0x4000	/* The actual count is valid */
-
-#define	I596_RBD_EL		0x8000	/* Last buffer in list */
-
-/************************************************************************/
-/*									*/
-/*	I596_RFD:	Receive Frame Descriptor (p. 4-79)		*/
-/*									*/
-/************************************************************************/
-typedef volatile struct _I596_RFD
-{
-	ushort			status;
-	ushort			cmd;
-	vol struct _I596_RFD	*next;
-	vol struct _I596_RBD	*rbdp;
-	ushort			count;	/* Len of data in RFD: always 0 */
-	ushort			size;	/* Size of RFD buffer: always 0 */
-
-	/* Application defined data follows structure... */
-
-#	if 0	/* We don't use these intel defined ones */
-		uchar		addr[6];
-		ushort		len;
-		uchar		data[1];
-#	else
-		ulong		dstchan;/* Used by multi-nic mode */
-#	endif
-} I596_RFD;
-
-#define	I596_RFD_C		0x8000	/* status: frame complete */
-#define	I596_RFD_B		0x4000	/* status: frame busy or waiting */
-#define	I596_RFD_OK		0x2000	/* status: frame OK */
-#define	I596_RFD_ERR_LENGTH	0x1000	/* status: length error */
-#define	I596_RFD_ERR_CRC	0x0800	/* status: CRC error */
-#define	I596_RFD_ERR_ALIGN	0x0400	/* status: alignment error */
-#define	I596_RFD_ERR_NOBUFS	0x0200	/* status: resource error */
-#define	I596_RFD_ERR_DMA	0x0100	/* status: DMA error */
-#define	I596_RFD_ERR_SHORT	0x0080	/* status: too short error */
-#define	I596_RFD_NOMATCH	0x0002	/* status: IA was not matched */
-#define	I596_RFD_COLLISION	0x0001	/* status: collision during receive */
-
-#define	I596_RFD_EL		0x8000	/* cmd: end of RFD list */
-#define	I596_RFD_FLEX		0x0008	/* cmd: Flexible mode */
-#define	I596_RFD_EOF		0x8000	/* count: last buffer in the frame */
-#define	I596_RFD_F		0x4000	/* count: The actual count is valid */
-
-/************************************************************************/
-/*									*/
-/*	Commands							*/
-/*									*/
-/************************************************************************/
-
-	/* values for cmd halfword in all the structs below */
-#define I596_CB_CMD		0x07	/* CB COMMANDS */
-#define I596_CB_CMD_NOP		0
-#define I596_CB_CMD_IA		1
-#define I596_CB_CMD_CONF	2
-#define I596_CB_CMD_MCAST	3
-#define I596_CB_CMD_XMIT	4
-#define I596_CB_CMD_TDR		5
-#define I596_CB_CMD_DUMP	6
-#define I596_CB_CMD_DIAG	7
-
-#define	I596_CB_CMD_EL		0x8000	/* CB is last in linked list */
-#define	I596_CB_CMD_S		0x4000	/* Suspend after execution */
-#define	I596_CB_CMD_I		0x2000	/* cause interrupt */
-
-	/* values for the status halfword in all the struct below */
-#define	I596_CB_STATUS		0xF000	/* All four status bits */
-#define	I596_CB_STATUS_C	0x8000	/* Command complete */
-#define	I596_CB_STATUS_B	0x4000	/* Command busy executing */
-#define	I596_CB_STATUS_C_OR_B	0xC000	/* Command complete or busy */
-#define	I596_CB_STATUS_OK	0x2000	/* Command complete, no errors */
-#define	I596_CB_STATUS_A	0x1000	/* Command busy executing */
-
-#define	I596_CB_NOLINK		((I596_CB *) 0xffffffff)
-
-/*
- *	I596_CB_NOP:	NOP Command (p. 4-34)
- */
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-} I596_CB_NOP;
-
-/*
- *	Same as above, but command and status in one ulong for speed
- */
-typedef volatile struct
-{
-	ulong			csr;
-	union _I596_CB		*next;
-} I596_CB_FAST;
-#define	FASTs(X)	(X)
-#define	FASTc(X)	((X)<<16)
-
-/*
- *	I596_CB_IA:	Individual (MAC) Address Command (p. 4-35)
- */
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-	uchar			addr[6];
-} I596_CB_IA;
-
-/*
- *	I596_CB_CONF:	Configure Command (p. 4-37)
- */
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-	uchar			conf[14];
-} I596_CB_CONF;
-
-#define	I596_CONF0_P		0x80	/* Enable RBD Prefetch Bit */
-#define	I596_CONF0_COUNT	14	/* Count of configuration bytes */
-
-#define	I596_CONF1_MON_OFF	0xC0	/* Monitor mode: Monitor off */
-#define	I596_CONF1_MON_ON	0x80	/* Monitor mode: Monitor on */
-#define	I596_CONF1_TxFIFO(W)	(W)	/* TxFIFO trigger, in words */
-
-#define	I596_CONF2_SAVEBF	0x80	/* Save bad frames */
-
-#define	I596_CONF3_ADDRLEN(B)	(B)	/* Address length */
-#define	I596_CONF3_NOSRCINSERT	0x08	/* Do not insert source address */
-#define	I596_CONF3_PREAMBLE8	0x20	/* 8 byte preamble */
-#define	I596_CONF3_LOOPOFF	0x00	/* Loopback: Off */
-#define	I596_CONF3_LOOPINT	0x40	/* Loopback: internal */
-#define	I596_CONF3_LOOPEXT	0xC0	/* Loopback: external */
-
-#define	I596_CONF4_LINPRI(ST)	(ST)	/* Linear priority: slot times */
-#define	I596_CONF4_EXPPRI(ST)	(ST)	/* Exponential priority: slot times */
-#define	I596_CONF4_IEEE_BOM	0	/* IEEE 802.3 backoff method */
-
-#define	I596_CONF5_IFS(X)	(X)	/* Interframe spacing in clocks */
-
-#define	I596_CONF6_ST_LOW(X)	(X&255)	/* Slot time, low byte */
-
-#define	I596_CONF7_ST_HI(X)	(X>>8)	/* Slot time, high bits */
-#define	I596_CONF7_RETRY(X)	(X<<4)	/* Max retry number */
-
-#define	I596_CONF8_PROMISC	0x01	/* Rcv all frames */
-#define	I596_CONF8_NOBROAD	0x02
-#define	I596_CONF8_MANCHESTER	0x04
-#define	I596_CONF8_TxNOCRS	0x08
-#define	I596_CONF8_NOCRC	0x10
-#define	I596_CONF8_CRC_CCITT	0x20
-#define	I596_CONF8_BITSTUFFING	0x40
-#define	I596_CONF8_PADDING	0x80
-
-#define	I596_CONF9_CSFILTER(X)	(X)
-#define	I596_CONF9_CSINT(X)	0x08
-#define	I596_CONF9_CDFILTER(X)	(X<<4)
-#define	I596_CONF9_CDINT(X)	0x80
-
-#define	I596_CONF10_MINLEN(X)	(X)	/* Minimum frame length */
-
-#define	I596_CONF11_PRECRS_	0x01	/* Preamble before carrier sense */
-#define	I596_CONF11_LNGFLD_	0x02	/* Padding in End of Carrier */
-#define	I596_CONF11_CRCINM_	0x04	/* CRC in memory */
-#define	I596_CONF11_AUTOTX	0x08	/* Auto retransmit */
-#define	I596_CONF11_CSBSAC_	0x10	/* Collision detect by src addr cmp. */
-#define	I596_CONF11_MCALL_	0x20	/* Multicast all */
-
-#define I596_CONF13_RESERVED	0x3f	/* Reserved: must be ones */
-#define I596_CONF13_MULTIA	0x40	/* Enable multiple addr. reception */
-#define I596_CONF13_DISBOF	0x80	/* Disable backoff algorithm */
-/*
- *	I596_CB_MCAST:	Multicast-Setup Command (p. 4-54)
- */
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-	ushort			count;		/* Number of 6-byte addrs that follow */
-	uchar			addr[6][1];
-} I596_CB_MCAST;
-
-/*
- *	I596_CB_XMIT:	Transmit Command (p. 4-56)
- */
-typedef	I596_TFD	I596_CB_XMIT;
-
-#define	I596_CB_XMIT_NOCRC	0x0010	/* cmd: No CRC insertion */
-#define	I596_CB_XMIT_FLEX	0x0008	/* cmd: Flexible memory mode */
-
-#define	I596_CB_XMIT_ERR_LATE	0x0800	/* status: error: late collision */
-#define	I596_CB_XMIT_ERR_NOCRS	0x0400	/* status: error: no carriers sense */
-#define	I596_CB_XMIT_ERR_NOCTS	0x0200	/* status: error: loss of CTS */
-#define	I596_CB_XMIT_ERR_UNDER	0x0100	/* status: error: DMA underrun */
-#define	I596_CB_XMIT_ERR_MAXCOL	0x0020	/* status: error: maximum collisions */
-#define	I596_CB_XMIT_COLLISIONS	0x000f	/* status: number of collisions */
-
-/*
- *	I596_CB_TDR:	Time Domain Reflectometry Command (p. 4-63)
- */
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-	ushort			time;
-} I596_CB_TDR;
-
-/*
- *	I596_CB_DUMP:	Dump Command (p. 4-65)
- */
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-	uchar			*buf;
-} I596_CB_DUMP;
-
-/*
- *	I596_CB_DIAG:	Diagnose Command (p. 4-77)
- */
-typedef volatile struct
-{
-	ushort			status;
-	ushort			cmd;
-	union _I596_CB		*next;
-} I596_CB_DIAG;
-
-/*
- *	I596_CB:	Command Block
- */
-typedef union _I596_CB
-{
-	I596_CB_NOP		nop;
-	I596_CB_IA		ia;
-	I596_CB_CONF		conf;
-	I596_CB_MCAST		mcast;
-	I596_CB_XMIT		xmit;
-	I596_CB_TDR		tdr;
-	I596_CB_DUMP		dump;
-	I596_CB_DIAG		diag;
-
-	/* command and status in one ulong for speed... */
-	I596_CB_FAST		fast;
-} I596_CB;
-
-/************************************************************************/
-/*									*/
-/*	I596_SCB:	System Configuration Block (p. 4-26)		*/
-/*									*/
-/************************************************************************/
-typedef volatile struct
-{
-	volatile ushort		status;		/* Status word */
-	volatile ushort		cmd;		/* Command word */
-	I596_CB		*cbp;
-	I596_RFD	*rfdp;
-	ulong		crc_errs;
-	ulong		align_errs;
-	ulong		resource_errs;
-	ulong		overrun_errs;
-	ulong		rcvcdt_errs;
-	ulong		short_errs;
-	ushort		toff;
-	ushort		ton;
-} I596_SCB;
-
-	/* cmd halfword values */
-#define	I596_SCB_ACK		0xF000	/* ACKNOWLEDGMENTS */
-#define	I596_SCB_ACK_CX		0x8000	/* Ack command completion */
-#define	I596_SCB_ACK_FR		0x4000	/* Ack received frame */
-#define	I596_SCB_ACK_CNA	0x2000	/* Ack command unit not active */
-#define	I596_SCB_ACK_RNR	0x1000	/* Ack rcv unit not ready */
-#define	I596_SCB_ACK_ALL	0xF000	/* Ack everything */
-
-#define	I596_SCB_CUC		0x0700	/* COMMAND UNIT COMMANDS */
-#define	I596_SCB_CUC_NOP	0x0000	/* No operation */
-#define	I596_SCB_CUC_START	0x0100	/* Start execution of first CB */
-#define	I596_SCB_CUC_RESUME	0x0200	/* Resume execution */
-#define	I596_SCB_CUC_SUSPEND	0x0300	/* Suspend after current CB */
-#define	I596_SCB_CUC_ABORT	0x0400	/* Abort current CB immediately */
-#define	I596_SCB_CUC_LOAD	0x0500	/* Load Bus throttle timers */
-#define	I596_SCB_CUC_LOADIMM	0x0600	/* Load Bus throttle timers, now */
-
-#define	I596_SCB_RUC		0x0070	/* RECEIVE UNIT COMMANDS */
-#define	I596_SCB_RUC_NOP	0x0000	/* No operation */
-#define	I596_SCB_RUC_START	0x0010	/* Start reception */
-#define	I596_SCB_RUC_RESUME	0x0020	/* Resume reception */
-#define	I596_SCB_RUC_SUSPEND	0x0030	/* Suspend reception */
-#define	I596_SCB_RUC_ABORT	0x0040	/* Abort reception */
-
-#define	I596_SCB_RESET		0x0080	/* Hard reset chip */
-
-	/* status halfword values */
-#define	I596_SCB_STAT		0xF000	/* STATUS */
-#define	I596_SCB_CX		0x8000	/* command completion */
-#define	I596_SCB_FR		0x4000	/* received frame */
-#define	I596_SCB_CNA		0x2000	/* command unit not active */
-#define	I596_SCB_RNR		0x1000	/* rcv unit not ready */
-
-#define	I596_SCB_CUS		0x0700	/* COMMAND UNIT STATUS */
-#define	I596_SCB_CUS_IDLE	0x0000	/* Idle */
-#define	I596_SCB_CUS_SUSPENDED	0x0100	/* Suspended */
-#define	I596_SCB_CUS_ACTIVE	0x0200	/* Active */
-
-#define	I596_SCB_RUS		0x00F0	/* RECEIVE UNIT STATUS */
-#define	I596_SCB_RUS_IDLE	0x0000	/* Idle */
-#define	I596_SCB_RUS_SUSPENDED	0x0010	/* Suspended */
-#define	I596_SCB_RUS_NORES	0x0020	/* No Resources */
-#define	I596_SCB_RUS_READY	0x0040	/* Ready */
-#define	I596_SCB_RUS_NORBDS	0x0080	/* No more RBDs modifier */
-
-#define	I596_SCB_LOADED		0x0008	/* Bus timers loaded */
-
-/************************************************************************/
-/*									*/
-/*	I596_ISCP:	Intermediate System Configuration Ptr (p 4-26)	*/
-/*									*/
-/************************************************************************/
-typedef volatile struct
-{
-	ulong		busy;	/* Set to 1; I596 clears it when scbp is read */
-	I596_SCB	*scbp;
-} I596_ISCP;
-
-/************************************************************************/
-/*									*/
-/*	I596_SCP:	System Configuration Pointer (p. 4-23)		*/
-/*									*/
-/************************************************************************/
-typedef volatile struct
-{
-	ulong		sysbus;
-	ulong		dummy;
-	I596_ISCP	*iscpp;
-} I596_SCP;
-
-	/* .sysbus values */
-#define I596_SCP_RESERVED	0x400000	/* Reserved bits must be set */
-#define I596_SCP_INTLOW		0x200000	/* Intr. Polarity active low */
-#define I596_SCP_INTHIGH	0		/* Intr. Polarity active high */
-#define I596_SCP_LOCKDIS	0x100000	/* Lock Function disabled */
-#define I596_SCP_LOCKEN		0		/* Lock Function enabled */
-#define I596_SCP_ETHROTTLE	0x080000	/* External Bus Throttle */
-#define I596_SCP_ITHROTTLE	0		/* Internal Bus Throttle */
-#define I596_SCP_LINEAR		0x040000	/* Linear Mode */
-#define I596_SCP_SEGMENTED	0x020000	/* Segmented Mode */
-#define I596_SCP_82586		0x000000	/* 82586 Mode */